Firefly开源社区

标题: ROC-RK3328-CC 烧写ubuntu16.04后,外接HDMI显示屏,上电启动无反应 [打印本页]

作者: CyanZee    时间: 2019-11-14 17:34
标题: ROC-RK3328-CC 烧写ubuntu16.04后,外接HDMI显示屏,上电启动无反应
Firefly--ROC-RK3328-CC开源主板烧写过程
前言:
本文讲述如何将主机上的原始固件烧写到SD卡,并以SD卡启动开发板。本文以ROC-RK3328-CC开发板为例。
官方教程:http://wiki.t-firefly.com/zh_CN/ROC-RK3328-CC/started.html
准备工作:
·主机、读卡器、SD卡、Firefly ROC-RK3328-CC 开发板、Micro USB电源线、电源适配器
·图形界面烧写工具SDCard Installer(可根据所使用的存储设备、所需的固件以及主机系统自行选择合适的烧写工具)
·原始固件ROC-RK3328-CC_Ubuntu 16.04_Arch64_20180514.img.xz
(以下是支持的系统列表:
Android7.1.2
Android8.1.0
Ubuntu18.04
Ubuntu16.04
Debian9
LibreELEC
可根据所需自行选择固件下载,ROC-RK3328-CC的固件下载页面http://www.t-firefly.com/doc/download/page/id/34.html
步骤:
Windows
1、将SD卡插入读卡器,并插到主机上。
2、以管理员身份运行安装好的烧写工具SDCard Installer。
3、点击“Choose an OS”按钮,在“Please select your device”框中选择“ROC-RK3328-CC”,再点击“Browse image file from local drive”选择本地已经下载好的固件ROC-RK3328-CC_Ubuntu 16.04_Arch64_20180514.img.xz,
4、烧写工具会自动识别SD卡,如果插有多张SD卡,可以点击“Change”按钮进行选择切换。
5、点击“Flash!”开始烧写,进度100%烧录完成。
6、将烧录好系统的SD卡插入开发板卡槽。
7、使用micro USB 线连接电源适配器和主板。
8、外接HDMI 显示屏,USB鼠标,USB键盘。
9、电源适配器上电。
问题描述:
1、上电启动后,红灯常亮,绿灯持续亮灯约5s后熄灭,外接显示屏无反应。(无串口调试,确定不了系统到底启没启动。)
2、尝试换官方上提供的其他原始固件重新烧录,结果还是一样。
重新烧录过的系统有:
ROC-RK3328-CC-ubuntu18.04-LXDE_20180920.img.xz
ROC-RK3328-CC_Ubuntu18.04_LXDE_20180717.img.xz
ROC-RK3328-CC-ubuntu18.04-LXDE_20181130.img
3、尝试换张SD卡重新烧录,得到的结果还是一样。
4、尝试长按3s Recovery键,无反应。

请问一下,没有串口调式的情况下,我接下来应该怎么定位问题?
作者: Lazyfan    时间: 2019-11-15 09:42
你好,今天又验证了一次,能够成功启动的。
每次操作前,先将您的SD卡格式化一下吧。
感觉你的操作流程都是正常的呀,应该不会有问题才对的
想要准确的确定问题的话,还是要看打印信息,不然没有办法准确的定位。

作者: CyanZee    时间: 2019-11-20 17:42
系统能够正常启动,但是外接显示屏依然无反应,我应该查看哪里?
作者: Lazyfan    时间: 2019-11-21 10:02
你的外接HDMI屏本身是可以使用的吗?
我自己验证是没有问题,HDMI显示可以,也能够启动。
还是建议你用几根杜邦线和串口去看看内核打印信息把,这样才能准确的知道问题在哪儿。
作者: CyanZee    时间: 2019-11-21 10:45
嗯嗯,已经连串口看日志了,但是不懂要看哪里

         Stopping Session c3 of user firefly.
[  OK  ] Stopped target Sound Card.
         Stopping Authenticate and Authorize Users to Run Privileged Tasks...
         Stopping Bluetooth service...
[  OK  ] Stopped target Timers.
         Stopping Save/Restore Sound Card State...
         Stopping Disk Manager...
         Stopping RealtimeKit Scheduling Policy Service...
[  OK  ] Stopped Daily apt upgrade and clean activities.
[  OK  ] Stopped target Graphical Interface.
         Stopping Accounts Service...
         Stopping Session c2 of user firefly.
[  OK  ] Stopped Daily Cleanup of Temporary Directories.
[  OK  ] Stopped target Multi-User System.
         Stopping Modem Manager...
         Stopping System Logging Service...
         Stopping LSB: Set the CPU Frequency Scaling governor to "ondemand"...
         Stopping Regular background program processing daemon...
[  OK  ] Stopped target Login Prompts.
         Stopping Serial Getty on ttyFIQ0...
         Stopping Getty on tty1...
         Stopping OpenBSD Secure Shell server...
         Stopping Make remote CUPS printers available locally...
         Stopping Run anacron jobs...
         Stopping Snappy daemon...
         Stopping Session c1 of user root.
[  OK  ] Stopped Timer to automatically refresh installed snaps.
         Stopping Daemon for power management...
[  OK  ] Closed Load/Save RF Kill Switch Status /dev/rfkill Watch.
         Stopping User Manager for UID 0...
         Stopping Light Display Manager...
         Stopping User Manager for UID 1000...
         Stopping LSB: automatic crash report generation...
[  OK  ] Stopped Daily apt download activities.
[  OK  ] Stopped Regular background program processing daemon.
[  OK  ] Stopped Accounts Service.
[  OK  ] Stopped System Logging Service.
[  OK  ] Stopped Snappy daemon.
[  OK  ] Stopped Run anacron jobs.
[  OK  ] Stopped Authenticate and Authorize Users to Run Privileged Tasks.
[  OK  ] Stopped Serial Getty on ttyFIQ0.
[  OK  ] Stopped Modem Manager.
[  OK  ] Stopped Getty on tty1.
[  OK  ] Stopped OpenBSD Secure Shell server.
[  OK  ] Stopped Daemon for power management.
[  OK  ] Stopped RealtimeKit Scheduling Policy Service.
[  OK  ] Stopped Bluetooth service.
[  OK  ] Stopped Disk Manager.
[  OK  ] Stopped Save/Restore Sound Card State.
[  OK  ] Stopped Session c1 of user root.
[  OK  ] Stopped User Manager for UID 0.
[  OK  ] Stopped User Manager for UID 1000.
[  OK  ] Stopped Light Display Manager.
[  OK  ] Stopped Make remote CUPS printers available locally.
[  OK  ] Stopped LSB: Set the CPU Frequency Scaling governor to "ondemand".
[  OK  ] Stopped LSB: automatic crash report generation.
         Stopping CUPS Scheduler...
         Stopping Avahi mDNS/DNS-SD Stack...
[  OK  ] Removed slice User Slice of root.
[  OK  ] Removed slice system-getty.slice.
[  OK  ] Stopped /etc/rc.local Compatibility.
[  OK  ] Stopped target Network is Online.
[  OK  ] Stopped target Network.
         Stopping Network Manager...
[  OK  ] Removed slice system-serial\x2dgetty.slice.
[  OK  ] Stopped target System Time Synchronized.
[  OK  ] Stopped Avahi mDNS/DNS-SD Stack.
[  OK  ] Stopped CUPS Scheduler.
[  OK  ] Stopped Network Manager.
         Stopping D-Bus System Message Bus...
[  OK  ] Stopped D-Bus System Message Bus.
[  OK  ] Stopped User Manager for UID 0.
[  OK  ] Removed slice user-0.slice.
[  OK  ] Unmounted /run/user/0.
[  OK  ] Stopped Session c3 of user firefly.
[  OK  ] Stopped Session c2 of user firefly.
[  OK  ] Removed slice User Slice of firefly.
         Stopping Permit User Sessions...
         Stopping Login Service...
[  OK  ] Stopped Login Service.
[  OK  ] Stopped Permit User Sessions.
[  OK  ] Stopped target Remote File Systems.
[  OK  ] Stopped target Remote File Systems (Pre).
[  OK  ] Stopped target Basic System.
[  OK  ] Stopped target Paths.
[  OK  ] Stopped Forward Password Requests to Wall Directory Watch.
[  OK  ] Stopped CUPS Scheduler.
[  OK  ] Stopped Dispatch Password Requests to Console Directory Watch.
[  OK  ] Stopped target Sockets.
[  OK  ] Closed Socket activation for snappy daemon.
[  OK  ] Closed Syslog Socket.
[  OK  ] Closed Avahi mDNS/DNS-SD Stack Activation Socket.
[  OK  ] Closed CUPS Scheduler.
[  OK  ] Closed D-Bus System Message Bus Socket.
[  OK  ] Stopped target System Initialization.
[  OK  ] Stopped Apply Kernel Variables.
         Stopping Network Time Synchronization...
[  OK  ] Stopped target Encrypted Volumes.
         Stopping Load/Save Random Seed...
[  OK  ] Stopped target Swap.
         Stopping Update UTMP about System Boot/Shutdown...
[  OK  ] Stopped target Slices.
[  OK  ] Removed slice User and Session Slice.
[  OK  ] Stopped target User and Group Name Lookups.
[  OK  ] Stopped Network Time Synchronization.
[  OK  ] Stopped Load/Save Random Seed.
[  OK  ] Stopped Update UTMP about System Boot/Shutdown.
[  OK  ] Stopped Create Volatile Files and Directories.
[  OK  ] Stopped target Local File Systems.
         Unmounting /run/user/1000...
[  OK  ] Unmounted /run/user/1000.
[  OK  ] Reached target Unmount All Filesystems.
[  OK  ] Stopped target Local File Systems (Pre).
[  OK  ] Stopped Remount Root and Kernel File Systems.
[  OK  ] Stopped Create Static Device Nodes in /dev.
[  OK  ] Reached target Shutdown.
[  108.352720] reboot: Restarting system with command 'now'
INFO:    PSCI Power Domain Map:
INFO:      Domain Node : Level 2, parent_node -1, State ON (0x0)
INFO:      Domain Node : Level 1, parent_node 0, State ON (0x0)
INFO:      Domain Node : Level 0, parent_node 0, State ON (0x0)
INFO:      Domain Node : Level 0, parent_node 0, State ON (0x0)
INFO:      CPU Node : MPID 0x0, parent_node 1, State ON (0x0)
INFO:      CPU Node : MPID 0x1, parent_node 1, State ON (0x0)
INFO:      CPU Node : MPID 0x2, parent_node 1, State ON (0x0)
INFO:      CPU Node : MPID 0x3, parent_node 1, State ON (0x0)
DDR version 1.06 20170424
In
SRX
DDR4
786MHz
Bus Width=32 Col=10 Bank=4 Bank Group=2 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
ddrconfig:14
OUT
Boot1 Release Time: 2017-05-18, version: 2.43
ChipType = 0x11, 266
emmc reinit
emmc reinit
SdmmcInit=2 400
SdmmcInit=0 0
BootCapSize=0
UserCapSize=60906MB
FwPartOffset=2000 , 0
StorageInit ok = 53573
Raw SecureMode = 0
SecureInit read PBA: 0x4
SecureInit read PBA: 0x404
SecureInit read PBA: 0x804
SecureInit read PBA: 0xc04
SecureInit read PBA: 0x1004
SecureInit ret = 0, SecureMode = 0
LoadTrustBL
No find bl30.bin
No find bl32.bin
Load uboot, ReadLba = 2000
Load OK, addr=0x200000, size=0xa53dc
RunBL31 0x10000
NOTICE:  BL31: v1.3(debug):f947c7e
NOTICE:  BL31: Built : 09:28:45, May 31 2017
NOTICE:  BL31:Rockchip release version: v1.3
INFO:    ARM GICv2 driver initialized
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 1
INFO:    plat_rockchip_pmu_init: pd status 0xe
INFO:    BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


U-Boot 2017.09-gde7626a-dirty (May 10 2018 - 15:47:25 +0800)

Model: Firefly ROC-RK3328-CC
DRAM:  1022 MiB
MMC:   rksdmmc@ff520000: 0, rksdmmc@ff500000: 1
*** Warning - bad CRC, using default environment

In:    serial@ff130000
Out:   serial@ff130000
Err:   serial@ff130000
Model: Firefly ROC-RK3328-CC
misc_init_r
cpuid=55524b54323430313700000000160926
serial=5fab23680da6ddb
normal boot
roc-rk3328-cc late init ...
Net:   No ethernet found.
Hit any key to stop autoboot:  0
Card did not respond to voltage select!
mmc_init: -95, time 2009
switch to partitions #0, OK
mmc1 is current device
aaaaaa Scanning mmc 1:4...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
reading /extlinux/extlinux.conf
180 bytes read in 3 ms (58.6 KiB/s)
1:      kernel-4.4
Retrieving file: /Image
reading /Image
16705544 bytes read in 741 ms (21.5 MiB/s)
append: earlycon=uart8250,mmio32,0xff130000 rw root=PARTUUID=b921b045-1d rootwait rootfstype=ext4 init=/sbin/init
Retrieving file: /rk3328-roc-cc.dtb
reading /rk3328-roc-cc.dtb
58485 bytes read in 5 ms (11.2 MiB/s)
## Flattened Device Tree blob at 01f00000
   Booting using the fdt blob at 0x1f00000
   Loading Device Tree to 000000003deef000, end 000000003df00474 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.114-00003-g78cbf59-dirty (zouxf@tchipser14) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9) ) #29 SMP Mon May 14 17:20:40 HKT 2018
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] earlycon: Early serial console at MMIO32 0xff130000 (options '')
[    0.000000] bootconsole [uart0] enabled
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc03ff4a000 s45800 r8192 d32024 u86016
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 257544
[    0.000000] Kernel command line: rockchip_jtag earlyprintk=uart8250-32bit,0xff130000 earlycon=uart8250,mmio32,0xff130000 rw root=PARTUUID=b921b045-1d rootwait rootfstype=ext4 init=/sbin/init
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[    0.000000] software IO TLB [mem 0x39eef000-0x3deef000] (64MB) mapped at [ffffffc039eef000-ffffffc03deeefff]
[    0.000000] Memory: 944804K/1046528K available (9982K kernel code, 1402K rwdata, 3764K rodata, 1088K init, 693K bss, 101724K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000   (   246 GB)
[    0.000000]       .init : 0xffffff8008e00000 - 0xffffff8008f10000   (  1088 KB)
[    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008a40000   (  9984 KB)
[    0.000000]     .rodata : 0xffffff8008a40000 - 0xffffff8008e00000   (  3840 KB)
[    0.000000]       .data : 0xffffff8008f10000 - 0xffffff800906e808   (  1403 KB)
[    0.000000]     vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
[    0.000000]               0xffffffbdc0008000 - 0xffffffbdc1000000   (    15 MB actual)
[    0.000000]     fixed   : 0xffffffbffe7fb000 - 0xffffffbffec00000   (  4116 KB)
[    0.000000]     PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000   (    16 MB)
[    0.000000]     memory  : 0xffffffc000200000 - 0xffffffc040000000   (  1022 MB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 64.
[    0.000000]  RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000009] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.001865] Console: colour dummy device 80x25
[    0.002286] console [tty0] enabled
[    0.002615] bootconsole [uart0] disabled
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.114-00003-g78cbf59-dirty (zouxf@tchipser14) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9) ) #29 SMP Mon May 14 17:20:40 HKT 2018
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] earlycon: Early serial console at MMIO32 0xff130000 (options '')
[    0.000000] bootconsole [uart0] enabled
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc03ff4a000 s45800 r8192 d32024 u86016
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 257544
[    0.000000] Kernel command line: rockchip_jtag earlyprintk=uart8250-32bit,0xff130000 earlycon=uart8250,mmio32,0xff130000 rw root=PARTUUID=b921b045-1d rootwait rootfstype=ext4 init=/sbin/init
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[    0.000000] software IO TLB [mem 0x39eef000-0x3deef000] (64MB) mapped at [ffffffc039eef000-ffffffc03deeefff]
[    0.000000] Memory: 944804K/1046528K available (9982K kernel code, 1402K rwdata, 3764K rodata, 1088K init, 693K bss, 101724K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000   (   246 GB)
[    0.000000]       .init : 0xffffff8008e00000 - 0xffffff8008f10000   (  1088 KB)
[    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008a40000   (  9984 KB)
[    0.000000]     .rodata : 0xffffff8008a40000 - 0xffffff8008e00000   (  3840 KB)
[    0.000000]       .data : 0xffffff8008f10000 - 0xffffff800906e808   (  1403 KB)
[    0.000000]     vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
[    0.000000]               0xffffffbdc0008000 - 0xffffffbdc1000000   (    15 MB actual)
[    0.000000]     fixed   : 0xffffffbffe7fb000 - 0xffffffbffec00000   (  4116 KB)
[    0.000000]     PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000   (    16 MB)
[    0.000000]     memory  : 0xffffffc000200000 - 0xffffffc040000000   (  1022 MB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 64.
[    0.000000]  RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000009] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.001865] Console: colour dummy device 80x25
[    0.002286] console [tty0] enabled
[    0.002615] bootconsole [uart0] disabled
[    0.003021] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=24000)
[    0.003058] pid_max: default: 32768 minimum: 301
[    0.003278] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[    0.003312] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[    0.004319] Initializing cgroup subsys devices
[    0.004363] Initializing cgroup subsys freezer
[    0.004409] ftrace: allocating 37112 entries in 145 pages
[    0.118485] sched-energy: CPU device node has no sched-energy-costs
[    0.118531] Invalid sched_group_energy for CPU0
[    0.118548] CPU0: update cpu_capacity 1024
[    0.118641] ASID allocator initialised with 32768 entries
[    0.124893] Detected VIPT I-cache on CPU1
[    0.124974] Invalid sched_group_energy for CPU1
[    0.124980] CPU1: update cpu_capacity 1024
[    0.124987] CPU1: Booted secondary processor [410fd034]
[    0.125804] Detected VIPT I-cache on CPU2
[    0.125861] Invalid sched_group_energy for CPU2
[    0.125868] CPU2: update cpu_capacity 1024
[    0.125873] CPU2: Booted secondary processor [410fd034]
[    0.126671] Detected VIPT I-cache on CPU3
[    0.126724] Invalid sched_group_energy for CPU3
[    0.126730] CPU3: update cpu_capacity 1024
[    0.126735] CPU3: Booted secondary processor [410fd034]
[    0.126865] Brought up 4 CPUs
[    0.127073] SMP: Total of 4 processors activated.
[    0.127112] CPU: All CPU(s) started at EL2
[    0.127178] alternatives: patching kernel code
[    0.127522] Invalid sched_group_energy for CPU3
[    0.127564] Invalid sched_group_energy for Cluster3
[    0.127598] Invalid sched_group_energy for CPU2
[    0.127626] Invalid sched_group_energy for Cluster2
[    0.127659] Invalid sched_group_energy for CPU1
[    0.127687] Invalid sched_group_energy for Cluster1
[    0.127720] Invalid sched_group_energy for CPU0
[    0.127747] Invalid sched_group_energy for Cluster0
[    0.128715] devtmpfs: initialized
[    0.152336] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[    0.152436] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.153168] xor: measuring software checksum speed
[    0.162953]    8regs     :  1080.000 MB/sec
[    0.173037]    8regs_prefetch:   968.000 MB/sec
[    0.183134]    32regs    :  1352.000 MB/sec
[    0.193220]    32regs_prefetch:  1116.000 MB/sec
[    0.193251] xor: using function: 32regs (1352.000 MB/sec)
[    0.193315] pinctrl core: initialized pinctrl subsystem
[    0.194860] NET: Registered protocol family 16
[    0.200378] cpuidle: using governor ladder
[    0.204403] cpuidle: using governor menu
[    0.204458] Registered FIQ tty driver
[    0.204896] vdso: 2 pages (1 code @ ffffff8008a46000, 1 data @ ffffff8008f14000)
[    0.204977] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.205201] DMA: preallocated 256 KiB pool for atomic allocations
[    0.234628] genirq: Setting trigger mode 8 for irq 175 failed (gic_set_type+0x0/0x68)
[    0.289797] console [ttyFIQ0] enabled
[    0.290556] Registered fiq debugger ttyFIQ0
[    0.326570] raid6: int64x1  gen()   187 MB/s
[    0.343704] raid6: int64x1  xor()   181 MB/s
[    0.360924] raid6: int64x2  gen()   292 MB/s
[    0.378123] raid6: int64x2  xor()   273 MB/s
[    0.395254] raid6: int64x4  gen()   457 MB/s
[    0.412397] raid6: int64x4  xor()   328 MB/s
[    0.429724] raid6: int64x8  gen()   332 MB/s
[    0.446809] raid6: int64x8  xor()   267 MB/s
[    0.463951] raid6: neonx1   gen()   359 MB/s
[    0.481159] raid6: neonx1   xor()   359 MB/s
[    0.498307] raid6: neonx2   gen()   562 MB/s
[    0.515474] raid6: neonx2   xor()   488 MB/s
[    0.532710] raid6: neonx4   gen()   757 MB/s
[    0.549854] raid6: neonx4   xor()   574 MB/s
[    0.567081] raid6: neonx8   gen()   773 MB/s
[    0.584245] raid6: neonx8   xor()   576 MB/s
[    0.584656] raid6: using algorithm neonx8 gen() 773 MB/s
[    0.585150] raid6: .... xor() 576 MB/s, rmw enabled
[    0.585622] raid6: using intx1 recovery algorithm
[    0.586673] mpp venc_srv: mpp_probe enter
[    0.587111] mpp venc_srv: init success
[    0.589725] vcc_sd: regulator get failed, ret=-517
[    0.591877] vcc_host_5v: regulator get failed, ret=-517
[    0.593133] vcc_host_5v: supplied by vcc_sys
[    0.595403] iommu: Adding device ff350000.vpu_service to group 0
[    0.596097] iommu: Adding device ff351000.avsd to group 1
[    0.596682] iommu: Adding device ff360000.rkvdec to group 2
[    0.597312] iommu: Adding device ff330000.h265e to group 3
[    0.597911] iommu: Adding device ff340000.vepu to group 4
[    0.598521] iommu: Adding device ff370000.vop to group 5
[    0.600303] rk_iommu ff360480.iommu: can't get aclk
[    0.600830] rk_iommu ff360480.iommu: can't get hclk
[    0.601521] rk_iommu ff330200.iommu: can't get aclk
[    0.602019] rk_iommu ff330200.iommu: can't get hclk
[    0.602922] rk_iommu ff373f00.iommu: can't get aclk
[    0.603409] rk_iommu ff373f00.iommu: can't get hclk
[    0.604665] SCSI subsystem initialized
[    0.605391] usbcore: registered new interface driver usbfs
[    0.606012] usbcore: registered new interface driver hub
[    0.606661] usbcore: registered new device driver usb
[    0.607269] media: Linux media interface: v0.10
[    0.607770] Linux video capture interface: v2.00
[    0.608303] pps_core: LinuxPPS API ver. 1 registered
[    0.608779] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.609705] PTP clock support registered
[    0.612259] Advanced Linux Sound Architecture Driver Initialized.
[    0.613770] Bluetooth: Core ver 2.21
[    0.614200] NET: Registered protocol family 31
[    0.614625] Bluetooth: HCI device and connection manager initialized
[    0.615240] Bluetooth: HCI socket layer initialized
[    0.615713] Bluetooth: L2CAP socket layer initialized
[    0.616244] Bluetooth: SCO socket layer initialized
[    0.618127] rockchip-cpuinfo cpuinfo: Serial         : 5fab23680da6ddb8
[    0.619659] clocksource: Switched to clocksource arch_sys_counter
[    0.734219] NET: Registered protocol family 2
[    0.735597] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.736443] TCP bind hash table entries: 8192 (order: 6, 262144 bytes)
[    0.737568] TCP: Hash tables configured (established 8192 bind 8192)
[    0.738321] UDP hash table entries: 512 (order: 3, 49152 bytes)
[    0.739005] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes)
[    0.740077] NET: Registered protocol family 1
[    0.741182] RPC: Registered named UNIX socket transport module.
[    0.741790] RPC: Registered udp transport module.
[    0.742235] RPC: Registered tcp transport module.
[    0.742702] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.744489] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[    0.750385] Initialise system trusted keyring
[    0.768064] NFS: Registering the id_resolver key type
[    0.768603] Key type id_resolver registered
[    0.769030] Key type id_legacy registered
[    0.769535] fuse init (API version 7.23)
[    0.770735] SGI XFS with security attributes, no debug enabled
[    0.778861] NET: Registered protocol family 38
[    0.779341] Key type asymmetric registered
[    0.779773] Asymmetric key parser 'x509' registered
[    0.780595] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.781328] io scheduler noop registered
[    0.781736] io scheduler deadline registered
[    0.782397] io scheduler cfq registered (default)
[    0.786318] rockchip-usb2phy ff450000.syscon:usb2-phy@100: vbus_drv is not assigned
[    0.788214] rockchip-u3phy ff470000.usb3-phy: vbus_drv is not assigned
[    0.791725] rockchip-u3phy ff470000.usb3-phy: Rockchip u3phy initialized successfully
[    0.796440] rk-vcodec vpu_combo: no regulator for vcodec
[    0.797323] rk-vcodec vpu_combo: failed on clk_get clk_cabac
[    0.797899] rk-vcodec vpu_combo: failed on clk_get clk_core
[    0.798519] platform ff350000.vpu_service: probe device
[    0.799103] platform ff350000.vpu_service: vpu mmu dec ffffffc03e5dac10
[    0.800104] platform ff350000.vpu_service: allocator is drm
[    0.800749] platform ff350000.vpu_service: checking hw id 0
[    0.802362] platform ff351000.avsd: probe device
[    0.803015] platform ff351000.avsd: vpu mmu dec ffffffc03e5dac10
[    0.804107] platform ff351000.avsd: allocator is drm
[    0.804684] platform ff351000.avsd: checking hw id 6731
[    0.807496] rk-vcodec vpu_combo: could not find power_model node
[    0.808107] rk-vcodec vpu_combo: init success
[    0.808997] rk-vcodec ff360000.rkvdec: no regulator for vcodec
[    0.809588] rk-vcodec ff360000.rkvdec: parent devfreq retry
[    0.811171] probe device ff330000.h265e
[    0.812016] mpp_dev ff330000.h265e: try to get iommu dev ffffffc03e5fc810
[    0.813226] mpp_dev ff330000.h265e: resource ready, register device
[    0.814480] probe device ff340000.vepu
[    0.815328] mpp_dev ff340000.vepu: try to get iommu dev ffffffc03e5fd010
[    0.816451] mpp_dev ff340000.vepu: resource ready, register device
[    0.820829] dma-pl330 ff1f0000.dmac: Loaded driver for PL330 DMAC-241330
[    0.821477] dma-pl330 ff1f0000.dmac:         DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[    0.823613] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled
[    0.827881] [drm] Initialized drm 1.1.0 20060810
[    0.832254] rockchip-drm display-subsystem: devfreq is not set
[    0.833332] rockchip-vop ff370000.vop: failed to get vop register byname
[    0.834050] rockchip-vop ff370000.vop: invalid resource
[    0.834545] rockchip-vop ff370000.vop: failed to get vop lut registers
[    0.835167] rockchip-vop ff370000.vop: invalid resource
[    0.835677] rockchip-vop ff370000.vop: failed to get vop cabc lut registers
[    0.836640] rockchip-drm display-subsystem: bound ff370000.vop (ops 0xffffff8008aeeb38)
[    0.837925] i2c i2c-4: of_i2c: modalias failure on /hdmi@ff3c0000/ports
[    0.838551] dwhdmi-rockchip ff3c0000.hdmi: registered DesignWare HDMI I2C bus driver
[    0.839429] dwhdmi-rockchip ff3c0000.hdmi: Detected HDMI TX controller v2.11a with HDCP (inno_dw_hdmi_phy2)
[    0.841872] rockchip-drm display-subsystem: bound ff3c0000.hdmi (ops 0xffffff8008ae69c8)
[    0.842679] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    0.843289] [drm] No driver support for vblank timestamp query.
[    0.843964] rockchip-drm display-subsystem: failed to parse display resources
[    0.844699] rockchip-drm display-subsystem: No connectors reported connected with modes
[    0.845502] [drm] Cannot find any crtc or sizes - going 1024x768
[    0.871786] Console: switching to colour frame buffer device 128x48
[    0.891926] rockchip-drm display-subsystem: fb0:  frame buffer device
[    0.903005] Unable to detect cache hierarchy for CPU 0
[    0.905220] brd: module loaded
[    0.916348] loop: module loaded
[    0.918005] zram: Added device: zram0
[    0.919012] lkdtm: No crash points registered, enable through debugfs
[    0.923407] rk_gmac-dwmac ff540000.ethernet: clock input or output? (input).
[    0.924385] rk_gmac-dwmac ff540000.ethernet: TX delay(0x25).
[    0.925138] rk_gmac-dwmac ff540000.ethernet: RX delay(0x11).
[    0.925898] rk_gmac-dwmac ff540000.ethernet: integrated PHY? (no).
[    0.926948] rk_gmac-dwmac ff540000.ethernet: cannot get clock clk_mac_speed
[    0.927859] rk_gmac-dwmac ff540000.ethernet: clock input from PHY
[    0.933677] rk_gmac-dwmac ff540000.ethernet: init for RGMII
[    0.934566] stmmac - user ID: 0x10, Synopsys ID: 0x35
[    0.935233]  Ring mode enabled
[    0.935659]  DMA HW capability register supported
[    0.936243]  Normal descriptors
[    0.936718]  RX Checksum Offload Engine supported (type 2)
[    0.937420]  TX Checksum insertion supported
[    0.937992]  Wake-Up On Lan supported
[    0.938542]  Enable RX Mitigation via HW Watchdog Timer
[    1.004047] libphy: stmmac: probed
[    1.004535] eth%d: PHY ID 001cc915 at 0 IRQ POLL (stmmac-0:00) active
[    1.013181] eth%d: PHY ID 001cc915 at 1 IRQ POLL (stmmac-0:01)
[    1.023112] Rockchip WiFi SYS interface (V1.00) ...
[    1.033875] phy phy-ff470000.usb3-phy.2: u3phy u2 power on
[    1.042290] phy phy-ff470000.usb3-phy.3: u3phy u3 power on
[    1.051855] ff580000.usb supply vusb_d not found, using dummy regulator
[    1.060474] ff580000.usb supply vusb_a not found, using dummy regulator
[    1.081519] dwc2 ff580000.usb: DWC OTG Controller
[    1.089754] dwc2 ff580000.usb: new USB bus registered, assigned bus number 1
[    1.098216] dwc2 ff580000.usb: irq 39, io mem 0xff580000
[    1.106711] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.115004] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.123212] usb usb1: Product: DWC OTG Controller
[    1.131087] usb usb1: Manufacturer: Linux 4.4.114-00003-g78cbf59-dirty dwc2_hsotg
[    1.139259] usb usb1: SerialNumber: ff580000.usb
[    1.148165] hub 1-0:1.0: USB hub found
[    1.155916] hub 1-0:1.0: 1 port detected
[    1.165054] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.172935] ehci-pci: EHCI PCI platform driver
[    1.180514] ehci-platform: EHCI generic platform driver
[    1.190861] ehci-platform ff5c0000.usb: EHCI Host Controller
[    1.198819] ehci-platform ff5c0000.usb: new USB bus registered, assigned bus number 2
[    1.206827] ehci-platform ff5c0000.usb: irq 40, io mem 0xff5c0000
[    1.219706] ehci-platform ff5c0000.usb: USB 2.0 started, EHCI 1.00
[    1.227430] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.234909] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.242377] usb usb2: Product: EHCI Host Controller
[    1.249558] usb usb2: Manufacturer: Linux 4.4.114-00003-g78cbf59-dirty ehci_hcd
[    1.257112] usb usb2: SerialNumber: ff5c0000.usb
[    1.265427] hub 2-0:1.0: USB hub found
[    1.272817] hub 2-0:1.0: 1 port detected
[    1.280875] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.288369] ohci-platform: OHCI generic platform driver
[    1.296348] ohci-platform ff5d0000.usb: Generic Platform OHCI controller
[    1.304455] ohci-platform ff5d0000.usb: new USB bus registered, assigned bus number 3
[    1.312541] ohci-platform ff5d0000.usb: irq 41, io mem 0xff5d0000
[    1.375016] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    1.382930] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.390911] usb usb3: Product: Generic Platform OHCI controller
[    1.398761] usb usb3: Manufacturer: Linux 4.4.114-00003-g78cbf59-dirty ohci_hcd
[    1.406840] usb usb3: SerialNumber: ff5d0000.usb
[    1.415726] hub 3-0:1.0: USB hub found
[    1.423564] hub 3-0:1.0: 1 port detected
[    1.432843] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    1.441251] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 4
[    1.449816] xhci-hcd xhci-hcd.9.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x00210010
[    1.458248] xhci-hcd xhci-hcd.9.auto: irq 179, io mem 0xff600000
[    1.466610] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[    1.474801] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.483136] usb usb4: Product: xHCI Host Controller
[    1.491205] usb usb4: Manufacturer: Linux 4.4.114-00003-g78cbf59-dirty xhci-hcd
[    1.499608] usb usb4: SerialNumber: xhci-hcd.9.auto
[    1.508946] hub 4-0:1.0: USB hub found
[    1.517138] hub 4-0:1.0: 1 port detected
[    1.525924] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    1.534709] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 5
[    1.543504] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
[    1.552432] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003
[    1.560989] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.569591] usb usb5: Product: xHCI Host Controller
[    1.577904] usb usb5: Manufacturer: Linux 4.4.114-00003-g78cbf59-dirty xhci-hcd
[    1.586502] usb usb5: SerialNumber: xhci-hcd.9.auto
[    1.595958] hub 5-0:1.0: USB hub found
[    1.604287] hub 5-0:1.0: 1 port detected
[    1.613438] usbcore: registered new interface driver usb-storage
[    1.622584] mousedev: PS/2 mouse device common for all mice
[    1.632845] usbcore: registered new interface driver usbtouchscreen
[    1.641974] .. rk pwm remotectl v1.1 init
[    1.651018] input: ff1b0030.pwm as /devices/platform/ff1b0030.pwm/input/input0
[    1.661489] i2c /dev entries driver
[    1.673328] rk808 1-0018: Pmic Chip id: 0x8050
[    1.683122] rk808 1-0018: source: on=0x40, off=0x00
[    1.705304] vcc_sd: supplied by vcc_io
[    1.723907] rk808 1-0018: register rk8050 regulators
[    1.732971] rk8xx-gpio rk8xx-gpio: register rk8050 gpio successful
[    1.752016] rk808-rtc rk808-rtc: rtc core: registered rk808-rtc as rtc0
[    1.761690] rk3x-i2c ff160000.i2c: Initialized RK3xxx I2C bus at ffffff80091b4000
[    1.772562] IR NEC protocol handler initialized
[    1.781896] usbcore: registered new interface driver uvcvideo
[    1.790684] USB Video Class driver (1.1.1)
[    1.804756] rockchip-thermal ff250000.tsadc: Missing tshut mode property, using default (cru)
[    1.814080] rockchip-thermal ff250000.tsadc: Missing tshut-polarity property, using default (low)
[    1.824694] Bluetooth: Virtual HCI driver ver 1.5
[    1.833971] Bluetooth: HCI UART driver ver 2.3
[    1.842746] Bluetooth: HCI UART protocol H4 registered
[    1.851463] Bluetooth: HCI UART protocol LL registered
[    1.860028] Bluetooth: HCI UART protocol ATH3K registered
[    1.868739] usbcore: registered new interface driver bfusb
[    1.877335] usbcore: registered new interface driver btusb
[    1.886380] cpu cpu0: cpu_leakage=7
[    1.894722] cpu cpu0: cpu_leakage=7
[    1.902793] cpu cpu0: cpu_leakage-volt-sel=0
[    1.914831] sdhci: Secure Digital Host Controller Interface driver
[    1.919190] sdhci: Copyright(c) Pierre Ossman
[    1.923237] Synopsys Designware Multimedia Card Interface Driver
[    1.928331] dwmmc_rockchip ff500000.dwmmc: IDMAC supports 32-bit address mode.
[    1.932832] dwmmc_rockchip ff500000.dwmmc: Using internal DMA controller.
[    1.937131] dwmmc_rockchip ff500000.dwmmc: Version ID is 270a
[    1.941295] dwmmc_rockchip ff500000.dwmmc: DW MMC controller at irq 36,32 bit host data width,256 deep fifo
[    1.945857] dwmmc_rockchip ff500000.dwmmc: 'clock-freq-min-max' property was deprecated.
[    1.950858] rockchip-iodomain ff100000.syscon:io-domains: Setting to 3300000 done
[    1.955396] gpio-regulator: set GRF_SOC_CON10 bit 1 to 0
[    1.959625] enter gpio_regulator_set_voltage line 107 ,gpio=1025 state=0
[    1.964025] rockchip-iodomain ff100000.syscon:io-domains: Setting to 3300000 done
[    1.978716] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    1.993738] dwmmc_rockchip ff500000.dwmmc: 1 slots initialized
[    1.998804] dwmmc_rockchip ff520000.dwmmc: IDMAC supports 32-bit address mode.
[    2.003455] dwmmc_rockchip ff520000.dwmmc: Using internal DMA controller.
[    2.007888] dwmmc_rockchip ff520000.dwmmc: Version ID is 270a
[    2.012220] dwmmc_rockchip ff520000.dwmmc: DW MMC controller at irq 37,32 bit host data width,256 deep fifo
[    2.016987] dwmmc_rockchip ff520000.dwmmc: 'clock-freq-min-max' property was deprecated.
[    2.021687] dwmmc_rockchip ff520000.dwmmc: No vmmc regulator found
[    2.026092] dwmmc_rockchip ff520000.dwmmc: No vqmmc regulator found
[    2.041681] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    2.056803] dwmmc_rockchip ff520000.dwmmc: 1 slots initialized
[    2.061438] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.067735] hidraw: raw HID events driver (C) Jiri Kosina
[    2.072587] usbcore: registered new interface driver usbhid
[    2.077019] usbhid: USB HID core driver
[    2.082205] rockchip-dmc dmc: unable to get devfreq-event device : dfi
[    2.088396] usbcore: registered new interface driver snd-usb-audio
[    2.093865] rk3328-codec ff410000.codec: spk_depop_time use default value.
[    2.101324] Initializing XFRM netlink socket
[    2.106447] NET: Registered protocol family 10
[    2.111958] NET: Registered protocol family 17
[    2.116299] NET: Registered protocol family 15
[    2.120570] Bluetooth: RFCOMM socket layer initialized
[    2.124816] Bluetooth: RFCOMM ver 1.11
[    2.128792] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    2.132989] Bluetooth: HIDP socket layer initialized
[    2.137048] [WLAN_RFKILL]: Enter rfkill_wlan_init
[    2.141339] [BT_RFKILL]: Enter rfkill_rk_init
[    2.145556] Key type dns_resolver registered
[    2.150225] Registered cp15_barrier emulation handler
[    2.154467] Registered setend emulation handler
[    2.159243] Loading compiled-in X.509 certificates
[    2.165393] Btrfs loaded
[    2.170085] rk-vcodec ff360000.rkvdec: no regulator for vcodec
[    2.174525] rk-vcodec ff360000.rkvdec: parent devfreq retry
[    2.179701] rockchip-dmc dmc: current ATF version 0x101!
[    2.184053] rockchip-dmc dmc: read tf version 0x101!
[    2.189646] rockchip-dmc dmc: ddr_leakage=7
[    2.193719] rockchip-dmc dmc: ddr_leakage-volt-sel=0
[    2.198184] rockchip-dmc dmc: failed to get vop bandwidth to dmc rate
[    2.223917] asoc-simple-card sound: rk3328-hifi <-> ff010000.i2s mapping ok
[    2.229220] asoc-simple-card hdmi-sound: i2s-hifi <-> ff000000.i2s mapping ok
[    2.233919] rk-vcodec ff360000.rkvdec: no regulator for vcodec
[    2.237820] rk-vcodec ff360000.rkvdec: parent devfreq is ok
[    2.241876] rk-vcodec ff360000.rkvdec: probe device
[    2.245536] rk-vcodec ff360000.rkvdec: vpu mmu dec ffffffc03e5fc010
[    2.249524] rk-vcodec ff360000.rkvdec: allocator is drm
[    2.253162] rk-vcodec ff360000.rkvdec: checking hw id 3410
[    2.257071] rk-vcodec ff360000.rkvdec: init success
[    2.262425] rk808-rtc rk808-rtc: setting system clock to 2019-11-21 02:36:29 UTC (1574303789)
[    2.275596] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 415; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '-release_v1.02-3-g78cbf59', rk_ko_ver is '5', built at '17:17:58', on 'May 14 2018'.
[    2.284172] mali-utgard ff300000.gpu: mali_platform_device->num_resources = 9
[    2.288118] mali-utgard ff300000.gpu: resource[0].start = 0x0x00000000ff300000
[    2.292035] mali-utgard ff300000.gpu: resource[1].start = 0x0x00000000ff300000
[    2.295899] mali-utgard ff300000.gpu: resource[2].start = 0x0x0000000000000010
[    2.299744] mali-utgard ff300000.gpu: resource[3].start = 0x0x0000000000000011
[    2.303482] mali-utgard ff300000.gpu: resource[4].start = 0x0x0000000000000012
[    2.307082] mali-utgard ff300000.gpu: resource[5].start = 0x0x0000000000000013
[    2.310647] mali-utgard ff300000.gpu: resource[6].start = 0x0x0000000000000014
[    2.314156] mali-utgard ff300000.gpu: resource[7].start = 0x0x0000000000000015
[    2.317581] mali-utgard ff300000.gpu: resource[8].start = 0x0x0000000000000016
[    2.320980] D : [File] : drivers/gpu/arm/mali400/mali/platform/rk/rk.c; [Line] : 617; [Func] : mali_platform_device_init(); to add platform_specific_data to platform_device_of_mali.
[    2.328157] mali-utgard ff300000.gpu: gpu_leakage=7
[    2.331424] mali-utgard ff300000.gpu: gpu_leakage-volt-sel=0
[    2.336334] Mali: Mali device driver loaded
[    2.340406] ALSA device list:
[    2.343515]   #0: rockchip,rk3328
[    2.346639]   #1: rockchip,hdmi
[    2.349870] Waiting for root device PARTUUID=b921b045-1d...
[    2.434684] devfreq ff300000.gpu: Couldn't update frequency transition information.
[    2.572641] dwmmc_rockchip ff520000.dwmmc: Busy; trying anyway
[    2.576128] mmc_host mmc1: Timeout sending command (cmd 0x202000 arg 0x0 status 0x0)
[    2.603674] rockchip-iodomain ff100000.syscon:io-domains: Setting to 3300000 done
[    2.607435] gpio-regulator: set GRF_SOC_CON10 bit 1 to 1
[    2.610995] enter gpio_regulator_set_voltage line 107 ,gpio=1025 state=1
[    2.614720] rockchip-iodomain ff100000.syscon:io-domains: Setting to 1800000 done
[    2.641762] mmc_host mmc0: Bus speed (slot 0) = 150000000Hz (slot req 150000000Hz, actual 150000000HZ div = 0)
[    3.276266] dwmmc_rockchip ff500000.dwmmc: Successfully tuned phase to 320
[    3.280220] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[    3.284507] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[    3.296019]  mmcblk0: p1 p2 p3 p4 p5
[    3.381065] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null)
[    3.385291] VFS: Mounted root (ext4 filesystem) on device 179:5.
[    3.391944] devtmpfs: mounted
[    3.396054] Freeing unused kernel memory: 1088K
[    3.530968] systemd[1]: Failed to insert module 'autofs4': No such file or directory
[    3.547001] random: systemd: uninitialized urandom read (16 bytes read, 22 bits of entropy available)
[    3.552828] random: systemd: uninitialized urandom read (16 bytes read, 22 bits of entropy available)
[    3.558097] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
[    3.567620] systemd[1]: Detected architecture arm64.

Welcome to Ubuntu 16.04.2 LTS!

[    3.579966] systemd[1]: Set hostname to <firefly>.
[    3.606863] random: systemd: uninitialized urandom read (16 bytes read, 23 bits of entropy available)
[    3.619836] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 23 bits of entropy available)
[    3.625075] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 24 bits of entropy available)
[    3.627494] random: systemd-cryptse: uninitialized urandom read (16 bytes read, 24 bits of entropy available)
[    3.632825] random: systemd-sysv-ge: uninitialized urandom read (16 bytes read, 24 bits of entropy available)
[    3.634989] random: systemd-sysv-ge: uninitialized urandom read (16 bytes read, 24 bits of entropy available)
[    3.644220] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 25 bits of entropy available)
[    3.648910] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 25 bits of entropy available)
[    3.861872] systemd[1]: Configuration file /etc/systemd/system/NetworkManager.service.d/carrier-detect.conf is marked executable. Please remove executable permission bits. Proceeding anyway.
[    3.885043] systemd[1]: Listening on udev Kernel Socket.
[  OK  ] Listening on udev Kernel Socket.
[    3.896339] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[  OK  ] Listening on /dev/initctl Compatibility Named Pipe.
[    3.901195] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[  OK  ] Started Forward Password Requests to Wall Directory Watch.
[    3.906324] systemd[1]: Reached target User and Group Name Lookups.
[  OK  ] Reached target User and Group Name Lookups.
[    3.911531] systemd[1]: Listening on udev Control Socket.
[  OK  ] Listening on udev Control Socket.
[    3.916802] systemd[1]: Created slice System Slice.
[  OK  ] Created slice System Slice.
[    3.921389] systemd[1]: Reached target Encrypted Volumes.
[  OK  ] Reached target Encrypted Volumes.
[    3.926046] systemd[1]: Reached target Swap.
[  OK  ] Reached target Swap.
[    3.930798] systemd[1]: Listening on Journal Socket.
[  OK  ] Listening on Journal Socket.
[    3.939769] systemd[1]: Starting Load Kernel Modules...
         Starting Load Kernel Modules...
[    3.944755] systemd[1]: Listening on Syslog Socket.
[  OK  ] Listening on Syslog Socket.
[    3.949419] systemd[1]: Listening on Journal Socket (/dev/log).
[  OK  ] Listening on Journal Socket (/dev/log).
[    3.954524] systemd[1]: Created slice User and Session Slice.
[  OK  ] Created slice User and Session Slice.
[    3.959092] systemd[1]: Reached target Slices.
[  OK  ] Reached target Slices.
[    3.964044] systemd[1]: Created slice system-serial\x2dgetty.slice.
[  OK  ] Created slice system-serial\x2dgetty.slice.
[    3.970034] systemd[1]: Starting Create list of required static device nodes for the current kernel...
         Starting Create list of required st... nodes for the current kernel...
[    3.976624] systemd[1]: Starting Remount Root and Kernel File Systems...
         Starting Remount Root and Kernel File Systems...
[    3.982862] systemd[1]: Starting Set console keymap...
         Starting Set console keymap...
[    3.988836] systemd[1]: Starting Journal Service...
         Starting Journal Service...
[    3.999745] systemd[1]: Mounting Debug File System...
         Mounting Debug File System...
[    4.004107] systemd[1]: Reached target Remote File Systems (Pre).
[  OK  ] Reached target Remote File Systems (Pre).
[    4.008694] systemd[1]: Reached target Remote File Systems.
[  OK  ] Reached target Remote File Systems.
[    4.015420] systemd[1]: systemd-modules-load.service: Main process exited, code=exited, status=1/FAILURE
[    4.020430] systemd[1]: Failed to start Load Kernel Modules.
[FAILED] Failed to start Load Kernel Modules.
See 'systemctl status systemd-modules-load.service' for details.
[    4.025079] systemd[1]: systemd-modules-load.service: Unit entered failed state.
[    4.032499] systemd[1]: systemd-modules-load.service: Failed with result 'exit-code'.
[    4.037478] systemd[1]: Started Create list of required static device nodes for the current kernel.
[  OK  ] Started Create list of required sta...ce nodes for the current kernel.
[    4.042917] systemd[1]: Started Remount Root and Kernel File Systems.
[  OK  ] Started Remount Root and Kernel File Systems.
[    4.095011] systemd[1]: Mounted Debug File System.
[  OK  ] Mounted Debug File System.
[    4.154750] systemd[1]: Started Set console keymap.
[  OK  ] Started Set console keymap.
[    4.171761] systemd[1]: Starting udev Coldplug all Devices...
         Starting udev Coldplug all Devices...
[    4.177779] systemd[1]: Starting Load/Save Random Seed...
         Starting Load/Save Random Seed...
[    4.184290] systemd[1]: Starting Create Static Device Nodes in /dev...
         Starting Create Static Device Nodes in /dev...
[    4.190737] systemd[1]: Mounting Configuration File System...
         Mounting Configuration File System...
[    4.197377] systemd[1]: Starting Apply Kernel Variables...
         Starting Apply Kernel Variables...
[    4.203681] systemd[1]: Mounting FUSE Control File System...
         Mounting FUSE Control File System...
[  OK  ] Mounted Configuration File System.
[  OK  ] Mounted FUSE Control File System.
[  OK  ] Started Journal Service.
[  OK  ] Started Load/Save Random Seed.
[  OK  ] Started Create Static Device Nodes in /dev.
[  OK  ] Started Apply Kernel Variables.
[  OK  ] Reached target Local File Systems (Pre).
[  OK  ] Reached target Local File Systems.
         Starting LSB: AppArmor initialization...
         Starting Set console font and keymap...
         Starting Tell Plymouth To Write Out Runtime Data...
         Starting udev Kernel Device Manager...
         Starting Flush Journal to Persistent Storage...
[  OK  ] Started Tell Plymouth To Write Out Runtime Data.
[  OK  ] Started udev Coldplug all Devices.
[  OK  ] Started Flush Journal to Persistent Storage.
         Starting Create Volatile Files and Directories...
[  OK  ] Started LSB: AppArmor initialization.
[  OK  ] Started Create Volatile Files and Directories.
         Starting Network Time Synchronization...
         Starting Update UTMP about System Boot/Shutdown...
[  OK  ] Started Network Time Synchronization.
[  OK  ] Started Update UTMP about System Boot/Shutdown.
[  OK  ] Reached target System Time Synchronized.
[  OK  ] Started udev Kernel Device Manager.
[  OK  ] Started Dispatch Password Requests to Console Directory Watch.
[  OK  ] Reached target System Initialization.
         Starting Socket activation for snappy daemon.
[  OK  ] Started Timer to automatically refresh installed snaps.
[  OK  ] Listening on D-Bus System Message Bus Socket.
[  OK  ] Started Daily Cleanup of Temporary Directories.
[  OK  ] Listening on CUPS Scheduler.
[  OK  ] Started CUPS Scheduler.
[  OK  ] Reached target Paths.
[  OK  ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
[  OK  ] Listening on Socket activation for snappy daemon.
[  OK  ] Reached target Sockets.
[  OK  ] Reached target Basic System.
         Starting Avahi mDNS/DNS-SD Stack...
[  OK  ] Started CUPS Scheduler.
         Starting Restore /etc/resolv.conf i...re the ppp link was shut down...
         Starting Login Service...
         Starting Modem Manager...
[  OK  ] Started D-Bus System Message Bus.
[  OK  ] Started Avahi mDNS/DNS-SD Stack.
         Starting Network Manager...
         Starting LSB: automatic crash report generation...
         Starting System Logging Service...
         Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"...
         Starting Permit User Sessions...
[  OK  ] Started Run anacron jobs.
         Starting Save/Restore Sound Card State...
         Starting Accounts Service...
[  OK  ] Started Make remote CUPS printers available locally.
[  OK  ] Started Regular background program processing daemon.
         Starting Snappy daemon...
[  OK  ] Started Set console font and keymap.
[  OK  ] Started Restore /etc/resolv.conf if...fore the ppp link was shut down.
[  OK  ] Started Save/Restore Sound Card State.
[  OK  ] Found device /dev/ttyFIQ0.
[  OK  ] Started System Logging Service.
[  OK  ] Started Permit User Sessions.
[  OK  ] Started Login Service.
         Starting Authenticate and Authorize Users to Run Privileged Tasks...
[  OK  ] Started ifup for eth0.
[  OK  ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
         Starting Light Display Manager...
[  OK  ] Reached target Sound Card.
[  OK  ] Created slice system-getty.slice.
[  OK  ] Started LSB: automatic crash report generation.
[  OK  ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand".
[  OK  ] Started Snappy daemon.
[  OK  ] Started Authenticate and Authorize Users to Run Privileged Tasks.
[  OK  ] Started Accounts Service.
         Starting Network Manager Script Dispatcher Service...
[  OK  ] Started Network Manager Script Dispatcher Service.
[  OK  ] Started Modem Manager.
         Starting Hostname Service...
[  OK  ] Started Hostname Service.
[  OK  ] Started Light Display Manager.
[  OK  ] Started Network Manager.
[  OK  ] Reached target Network.
[  OK  ] Reached target Network is Online.
         Starting /etc/rc.local Compatibility...
[  OK  ] Started Daily apt download activities.
[  OK  ] Started Daily apt upgrade and clean activities.
[  OK  ] Reached target Timers.
         Starting OpenBSD Secure Shell server...
[  OK  ] Started /etc/rc.local Compatibility.
         Starting Hold until boot process finishes up...
[  OK  ] Started Hold until boot process finishes up.
[  OK  ] Started Serial Getty on ttyFIQ0.
[  OK  ] Started Getty on tty1.
[  OK  ] Reached target Login Prompts.
         Starting Set console scheme...
[  OK  ] Started Set console scheme.
[  OK  ] Started OpenBSD Secure Shell server.
[  OK  ] Reached target Multi-User System.
[  OK  ] Reached target Graphical Interface.
         Starting Update UTMP about System Runlevel Changes...
[  OK  ] Started Update UTMP about System Runlevel Changes.

Ubuntu 16.04.2 LTS firefly ttyFIQ0

firefly login: root (automatic login)

Last login: Thu Nov 21 10:34:31 CST 2019 on ttyFIQ0
Welcome to Ubuntu 16.04.2 LTS (GNU/Linux 4.4.114-00003-g78cbf59-dirty aarch64)

* Documentation:  https://help.ubuntu.com
* Management:     https://landscape.canonical.com
* Support:        https://ubuntu.com/advantage

作者: Lazyfan    时间: 2019-11-25 09:27
你发的Log表明,系统已经跑起来了,应该可以显示呀
这样,你试着烧写一下Android7.1的固件,看看HDMI会不会有显示:Android7.1固件下载地址
作者: CyanZee    时间: 2019-11-26 09:58
嗯嗯,烧写了Android7.1.2原始固件,RK固件也试过了,还试了Android8的,还是HDMI无显示,系统可以跑起来。

作者: darrendong    时间: 2019-12-20 11:24
CyanZee 发表于 2019-11-26 09:58
嗯嗯,烧写了Android7.1.2原始固件,RK固件也试过了,还试了Android8的,还是HDMI无显示,系统可以跑起来。 ...

我新买的PX30板子,烧写的官方的内核,屏幕HDMI同样没反应,请问一下你的问题解决没有?
作者: 熏肉    时间: 2020-1-4 00:13
同样的问题,3328的板子,换了卡 换了固件 hdmi都没有显示
作者: Lazyfan    时间: 2020-1-4 17:03
darrendong 发表于 2019-12-20 11:24
我新买的PX30板子,烧写的官方的内核,屏幕HDMI同样没反应,请问一下你的问题解决没有?

你好,PX30本身就不支持HDMI显示器,在对应的WIKI就有说明,可以仔细阅读一下。
作者: Lazyfan    时间: 2020-1-4 17:05
熏肉 发表于 2020-1-4 00:13
同样的问题,3328的板子,换了卡 换了固件 hdmi都没有显示

烧录的是哪个固件?系统跑起来了?如果系统跑起来了,一般正常的HDMI屏的话,是会显示。如果有出错信息的话,还是建议接个串口看看信息吧。
作者: zzxdcs    时间: 2020-4-21 21:27
我的都能正常显示
作者: 木自为柏    时间: 2020-5-27 09:12
请问楼主问题解决了没有
作者: 木自为柏    时间: 2020-5-27 11:59
我刚刚也是这个问题,换直流电源供电就可以了

作者: zhou66    时间: 2020-11-5 07:51
你们的显示器是不是也是DVI接口?是不是通过“hdmi转dvi线”连接到板上?
作者: 游泳贱将    时间: 2020-11-6 10:18
问题解决了吗?我也出现了类似的问题,SD卡烧Ubuntu固件可以运行界面,SD卡烧Android原始固件HDMI显示器没有显示,试了几个版本都不行




欢迎光临 Firefly开源社区 (https://dev.t-firefly.com/) Powered by Discuz! X3.1