Firefly开源社区

标题: 板子没有接任何显示设备,就老是提示这个 [打印本页]

作者: jjlin77    时间: 2015-12-6 17:52
标题: 板子没有接任何显示设备,就老是提示这个
指示灯时按时灭,打印信息打印这个,断断续续,请问这个是什么意思啊?


[   61.758344] Suspended for 0.000 seconds
[   61.759462] Enabling non-boot CPUs ...
[   61.760083] CPU1: Booted secondary processor
[   61.761317] CPU1 is up
[   61.761718] CPU2: Booted secondary processor
[   61.762360] CPU2 is up
[   61.762764] CPU3: Booted secondary processor
[   61.763391] CPU3 is up
[   61.766096] PM: noirq resume of devices complete after 2.713 msecs
[   61.766809] PM: early resume of devices complete after 0.460 msecs
[   61.767265] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 52000000Hz, actual 50000000HZ div = 1)
[   61.767279] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out normal clock [mmc0]
[   61.767649] 1390..dw_mci_set_ios:  no card. [mmc1]
[   61.767715] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[   61.767726] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out normal clock [mmc2]
[   61.767894] dwc_otg_hcd_resume, usb device mode
[   61.768116] ff540000.usb resume, HPRT0:0x1485
[   61.773066] phy_power_on: enable = 1
[   61.807814] [WLAN_RFKILL]: Enter rfkill_wlan_resume
[   61.810782] rk_spdif:spdif:Entered spdif_resume
[   62.182106] usb 3-1.4: reset low-speed USB device number 3 using usb20_host
[   62.471822] PM: resume of devices complete after 716.452 msecs
[   62.472172] cpufreq: cpufreq_resume: Failed to start governor for policy: ee392f00
[   62.472184] cpufreq: cpufreq_resume: Failed to start governor for policy: ee392f00
[   62.472193] cpufreq: cpufreq_resume: Failed to start governor for policy: ee392f00
[   62.473184] [BT_RFKILL]: ** disable irq
[   62.738527] Restarting tasks ... done.
[   62.745418] PM: suspend exit 2011-01-01 12:01:21.951298250 UTC
[   64.563561] PM: suspend entry 2011-01-01 12:01:23.798884751 UTC
[   64.569587] PM: Syncing filesystems ... done.
[   64.613212] Freezing user space processes ... (elapsed 0.006 seconds) done.
[   64.626214] Freezing remaining freezable tasks ... (elapsed 0.004 seconds) done.
[   64.638144] Suspending console(s) (use no_console_suspend to debug)
01-armoff-logdp-osc_offddrc_off2345d




作者: 暴走的阿Sai    时间: 2015-12-7 10:30
如果是RK3288的板子,先确认电源是电压5V,电流2.5A以上
作者: jjlin77    时间: 2015-12-7 10:42
本帖最后由 jjlin77 于 2015-12-7 10:54 编辑
暴走的阿Sai 发表于 2015-12-7 10:30
如果是RK3288的板子,先确认电源是电压5V,电流2.5A以上

我确认是5V-2.5A 只要我接上HDMI的显示器,就不会提示这个,它提示这个不是重启,是断断续续,程序感觉是在跑的,进入了suspended状态吧
作者: tangyu1121    时间: 2015-12-7 15:54
jjlin77 发表于 2015-12-7 10:42
我确认是5V-2.5A 只要我接上HDMI的显示器,就不会提示这个,它提示这个不是重启,是断断续续,程序感觉是 ...

恩   是休眠状态!
有中端唤醒机器了
作者: jjlin77    时间: 2015-12-7 16:06
tangyu1121 发表于 2015-12-7 15:54
恩   是休眠状态!
有中端唤醒机器了

那这位大哥,你知道怎么调,不接HDMI,也不让他进入休眠状态吗?我现在没有屏幕,电视机和电脑不能随便搬动,所以,很多情况都是直接adb debug,不接屏幕,所以需要不接屏幕也不进入休眠啊
作者: tangyu1121    时间: 2015-12-9 13:58
jjlin77 发表于 2015-12-7 16:06
那这位大哥,你知道怎么调,不接HDMI,也不让他进入休眠状态吗?我现在没有屏幕,电视机和电脑不能随便搬 ...

1、可以把设置里面  安全-》屏幕锁定-》   这个设置项设置为无;
2、然后把机器的休眠时间:设置为永不休眠 ---  这个在论坛上有解决方法的  你搜索一下
这样机器开起来之后就不会进去休眠模式了
作者: sheqw    时间: 2018-6-11 16:16
楼主解决了吗?我也遇到了




欢迎光临 Firefly开源社区 (https://dev.t-firefly.com/) Powered by Discuz! X3.1