Firefly开源社区

12
发表新贴

制作ubuntu根文件系统时遇到的难题

164

积分

0

威望

0

贡献

技术小白

积分
164
发表于 2016-8-10 14:44:20     
按照维基的教程:http://wiki.t-firefly.com/index. ... 88/Build_Ubuntu_rfs
用miniroot启动正常,固化系统后,烧写入0x0002e000(linuxroot),
启动后发现错误log:
mount: mounting /dev on /root/dev failed: No such file or directory
done.
mount: mounting /sys on /root/sys failed: No such file or directory
mount: mounting /proc on /root/proc failed: No such file or directory
Target filesystem doesn't have requested /sbin/init.
No init found. Try passing init= bootarg.
FATAL: Could not load /lib/modules/3.10.0/modules.dep: No such file or directory
FATAL: Could not load /lib/modules/3.10.0/modules.dep: No such file or directory
/bin/sh: can't access tty; job control turned off
(initramfs) [    7.840458] usb 3-1.1: new high-speed USB device number 3 using usb20_host
[    7.944387] usb 3-1.1: New USB device found, idVendor=0930, idProduct=6545
[    7.951356] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    7.958627] usb 3-1.1: Product: DT 101 G2
[    7.962600] usb 3-1.1: Manufacturer: Kingston
[    7.966911] usb 3-1.1: SerialNumber: 6C626D7C27E6ECC080000107
[    7.973797] usb-storage 3-1.1:1.0: USB Mass Storage device detected
[    7.981116] scsi0 : usb-storage 3-1.1:1.0
[    9.044728] scsi 0:0:0:0: Direct-Access     Kingston DT 101 G2        PMAP PQ: 0 ANSI: 4
[    9.056972] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   10.449480] sd 0:0:0:0: [sda] 30489408 512-byte logical blocks: (15.6 GB/14.5 GiB)
[   10.458617] sd 0:0:0:0: [sda] Write Protect is off
[   10.464207] sd 0:0:0:0: [sda] No Caching mode page found
[   10.469574] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   10.480844] sd 0:0:0:0: [sda] No Caching mode page found
[   10.486122] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   10.512422]  sda: sda4
[   10.518536] sd 0:0:0:0: [sda] No Caching mode page found
[   10.523820] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   10.530047] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   13.400173] es8323_create file error
[   20.484873] *****************vbus detect*******************
(initramfs)
(initramfs)        

查阅了很多资料,还是无法解决,请大家指点。
回复

使用道具 举报

164

积分

0

威望

0

贡献

技术小白

积分
164
发表于 2016-8-10 14:45:42     
我觉得主要问题是:
mount: mounting /dev on /root/dev failed: No such file or directory
done.
mount: mounting /sys on /root/sys failed: No such file or directory
mount: mounting /proc on /root/proc failed: No such file or directory
Target filesystem doesn't have requested /sbin/init.
为什么会mount失败呢?
回复

使用道具 举报

600

积分

21

威望

25

贡献

技术大神

Rank: 3Rank: 3

积分
600

活跃会员

发表于 2016-8-10 16:00:18     
楼主是用单系统还是双系统?parameter里的分区要和你烧进去的分区位置一致哦
回复

使用道具 举报

164

积分

0

威望

0

贡献

技术小白

积分
164
发表于 2016-8-11 08:58:38     
linjc 发表于 2016-8-10 16:00
楼主是用单系统还是双系统?parameter里的分区要和你烧进去的分区位置一致哦

感谢你的回答,这个问题解决了。
现在遇到一个新的问题:
编译的boot文件启动根文件系统,发现lubuntu可以正常工作,但是串口卡死,log如下:
Starting kernel ...

<hit enter to activate fiq debugger>
[    0.000000] Booting Linux on physical CPU 0x500
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.10.0 (malt@socsi-dev) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #2 SMP PREEMPT Wed Aug 10 17:44:41 CST 2016
[    0.000000] CPU: ARMv7 Processor [410fc0d1] revision 1 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: Rockchip RK3288 (Flattened Device Tree), model: rockchip,rk3288
[    0.000000] hdmi init vic is -1
[    0.000000] rockchip_ion_reserve
[    0.000000] cma: CMA: reserved 16 MiB at 2e800000
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] PERCPU: Embedded 9 pages/cpu @c2ec8000 s14016 r8192 d14656 u36864
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 1042960
[    0.000000] Kernel command line: console=tty0 console=ttyS2 earlyprintk root=/dev/block/mtd/by-name/linuxroot rw rootfstype=ext4 init=/sbin/init  mtdparts=rk29xxnand:0x00008000@0x00002000(resource),0x00008000@0x0000A000(boot),0x00002000@0x00012000(misc),0x0001a000@0x00014000(backup),-@0x0002e000(linuxroot) storagemedia=emmc loader.timestamp=2015-01-21_17:07:53 hdmi.vic=-1
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 4080MB = 4080MB total
[    0.000000] Memory: 4110028k/4110028k available, 67892k reserved, 3399680K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0a9bb1c   (10831 kB)
[    0.000000]       .init : 0xc0a9c000 - 0xc0cec6c0   (2370 kB)
[    0.000000]       .data : 0xc0cee000 - 0xc0d8d888   ( 639 kB)
[    0.000000]        .bss : 0xc0d8d888 - 0xc0eaa844   (1140 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] rk_clk_tree_init start! cru base = 0xfed00000
[    0.000000] rk_get_uboot_display_flag: uboot_logo_on = 0
[    0.000000] rkclk_init_clks: cnt_parent = 7
[    0.000000] rkclk_init_clks: cnt_rate = 32
[    0.000000] Architected local timer running at 24.00MHz (phys).
[    0.000000] Switching to timer-based delay loop
[    0.000000] sched_clock: ARM arch timer >56 bits at 24000kHz, resolution 41ns
[    0.000000] process version: 2
[    0.000000] channel:0, lkg:10
[    0.000000] target-temp:95
[    0.000000] channel:2, lkg:0
[    0.000000] target-temp:95
[    0.000000] channel:0, lkg:10
[    0.000000] target-temp:95
[    0.000000] channel:1, lkg:11
[    0.000000] target-temp:95
[    0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [tty0] enabled
[    1.035613] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    1.035721] pid_max: default: 32768 minimum: 301
[    1.036086] Security Framework initialized
[    1.036154] SELinux:  Initializing.
[    1.036416] Mount-cache hash table entries: 512
[    1.038494] Initializing cgroup subsys debug
[    1.038572] Initializing cgroup subsys freezer
[    1.038690] CPU: Testing write buffer coherency: ok
[    1.039482] /cpus/cpu@0 missing clock-frequency property
[    1.039561] /cpus/cpu@1 missing clock-frequency property
[    1.039625] /cpus/cpu@2 missing clock-frequency property
[    1.039688] /cpus/cpu@3 missing clock-frequency property
[    1.039842] CPU0: thread -1, cpu 0, socket 5, mpidr 80000500
[    1.039985] Setting up static identity map for 0xc07a6fc8 - 0xc07a7020
[    1.044246] last_log: 0x2e100000 map to 0xf0004000 and copy to 0xf0086000, size 0x80000 early 0x1401 (version 3.0)
[    1.121330] CPU1: Booted secondary processor
[    1.121420] CPU1: thread -1, cpu 1, socket 5, mpidr 80000501
[    1.141071] CPU2: Booted secondary processor
[    1.141154] CPU2: thread -1, cpu 2, socket 5, mpidr 80000502
[    1.160856] CPU3: Booted secondary processor
[    1.160938] CPU3: thread -1, cpu 3, socket 5, mpidr 80000503
[    1.161312] Brought up 4 CPUs
[    1.161599] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[    1.161662] CPU: All CPU(s) started in SVC mode.
[    1.163923] devtmpfs: initialized
[    1.181426] pinctrl core: initialized pinctrl subsystem
[    1.182209] regulator-dummy: no parameters
[    1.183866] NET: Registered protocol family 16
[    1.188977] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    1.190062] ion_snapshot: 0x2e1b0000 map to 0xf0107000 and copy to 0xc0e85e94 (version 0.1)
[    1.190612] Registered FIQ tty driver
[    1.194081] console [ttyFIQ0] enabled
[    1.194665] Registered fiq debugger ttyFIQ0
[    1.196409] rockchip_get_bank_data:name=base start=0xff750000,end=0xff7500ff
[    1.196538] rockchip_get_bank_data:name=mux_bank0 start=0xff730084,end=0xff73008f
[    1.196675] rockchip_get_bank_data:name=pull_bank0 start=0xff730064,end=0xff73006f
[    1.196797] rockchip_get_bank_data:name=drv_bank0 start=0xff730070,end=0xff73007b
[    1.197106] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio1@ff780000 start=0xff780000,end=0xff7800ff
[    1.197398] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio2@ff790000 start=0xff790000,end=0xff7900ff
[    1.197683] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio3@ff7a0000 start=0xff7a0000,end=0xff7a00ff
[    1.197967] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio4@ff7b0000 start=0xff7b0000,end=0xff7b00ff
[    1.198252] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio5@ff7c0000 start=0xff7c0000,end=0xff7c00ff
[    1.198538] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio6@ff7d0000 start=0xff7d0000,end=0xff7d00ff
[    1.198822] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio7@ff7e0000 start=0xff7e0000,end=0xff7e00ff
[    1.199106] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio8@ff7f0000 start=0xff7f0000,end=0xff7f00ff
[    1.199468] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio15@ff7f2000 start=0xff7f2000,end=0xff7f20ff
[    1.199775] rockchip_pinctrl_probe:name=RK3288-GPIO,type=3
[    1.199867] rockchip_pinctrl_probe:name=base start=0xff770000,end=0xff77013f
[    1.199958] rockchip_pinctrl_probe:name=pull start=0xff770140,end=0xff7701bf
[    1.200046] rockchip_pinctrl_probe:name=drv start=0xff7701c0,end=0xff77023f
[    1.201839] rockchip_interrupts_register:bank_num=7
[    1.208732] of_get_gpio_init_config:gpio[0] = 256, value = 0
[    1.208856] of_get_gpio_init_config:gpio[1] = 233, value = 0
[    1.208970] of_get_gpio_init_config:gpio[2] = 136, value = 0
[    1.209211] rockchip_pinctrl_probe:init ok
[    1.229258] rk_iommu ff900800.iep_mmu: (iep) Enter
[    1.229655] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[    1.229746] rk_iommu ff900800.iep_mmu: (iep) Initialized
[    1.230354] rk_iommu ff950800.vip_mmu: (vip) Enter
[    1.230711] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[    1.230798] rk_iommu ff950800.vip_mmu: (vip) Initialized
[    1.231375] rk_iommu ff930300.vopb_mmu: (vopb) Enter
[    1.231727] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[    1.231816] rk_iommu ff930300.vopb_mmu: (vopb) Initialized
[    1.232412] rk_iommu ff940300.vopl_mmu: (vopl) Enter
[    1.232766] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[    1.232855] rk_iommu ff940300.vopl_mmu: (vopl) Initialized
[    1.233454] rk_iommu ff9c0440.hevc_mmu: (hevc) Enter
[    1.233870] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[    1.233958] rk_iommu ff9c0440.hevc_mmu: (hevc) Initialized
[    1.234550] rk_iommu ff9a0800.vpu_mmu: (vpu) Enter
[    1.234920] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[    1.235009] rk_iommu ff9a0800.vpu_mmu: (vpu) Initialized
[    1.235661] rk_iommu ff914000.isp_mmu: (isp_mmu) Enter
[    1.236072] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[    1.236157] rk_iommu ff914000.isp_mmu: (isp_mmu) Initialized
[    1.241860] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    1.241971] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    1.242637] DDR DEBUG: version 1.00 20140603
[    1.242752] DDR DEBUG: Channel a:
[    1.242813] DDR DEBUG: DDR3 Device
[    1.242885] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=15 CS=2 Total Capability=2048MB
[    1.242974] DDR DEBUG: Channel b:
[    1.243028] DDR DEBUG: DDR3 Device
[    1.243096] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=15 CS=2 Total Capability=2048MB
[    1.243186] DDR DEBUG: addr=0xd93000
[    1.243248] DDR DEBUG: stride=13, size=256, halfcap=80000000
[    1.243319] DDR DEBUG: socAddr[0]=0xd93000, socAddr[1]=0xd93100
[    1.243392] DDR DEBUG: chAddr[0]=0xd93000, chAddr[1]=0xd93000
[    1.243468] DDR DEBUG: dtar[0]=0x301b2000, dtar[1]=0x301b2000
[    1.243660] DDR DEBUG: init success!!! freq=200MHz
[    1.243724] DDR DEBUG: Channel a:
[    1.243796] DDR DEBUG: DTONE=0x3, DTERR=0x0, DTIERR=0x0, DTPASS=4,4, DGSL=1,1 extra clock, DGPS=180,180
[    1.243908] DDR DEBUG: DTONE=0x3, DTERR=0x0, DTIERR=0x0, DTPASS=4,4, DGSL=1,1 extra clock, DGPS=180,180
[    1.244020] DDR DEBUG: DTONE=0x3, DTERR=0x0, DTIERR=0x0, DTPASS=4,4, DGSL=1,1 extra clock, DGPS=180,180
[    1.244130] DDR DEBUG: DTONE=0x3, DTERR=0x0, DTIERR=0x0, DTPASS=4,4, DGSL=1,1 extra clock, DGPS=180,180
[    1.244236] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0
[    1.244314] DDR DEBUG: DRV Pull-Up=0x19, DRV Pull-Dwn=0x19
[    1.244383] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2
[    1.244446] DDR DEBUG: Channel b:
[    1.244514] DDR DEBUG: DTONE=0x3, DTERR=0x0, DTIERR=0x0, DTPASS=4,4, DGSL=1,1 extra clock, DGPS=180,180
[    1.244624] DDR DEBUG: DTONE=0x3, DTERR=0x0, DTIERR=0x0, DTPASS=4,4, DGSL=1,1 extra clock, DGPS=180,180
[    1.244733] DDR DEBUG: DTONE=0x3, DTERR=0x0, DTIERR=0x0, DTPASS=4,4, DGSL=1,1 extra clock, DGPS=180,180
[    1.244843] DDR DEBUG: DTONE=0x3, DTERR=0x0, DTIERR=0x0, DTPASS=4,4, DGSL=1,1 extra clock, DGPS=180,180
[    1.244946] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0
[    1.245025] DDR DEBUG: DRV Pull-Up=0x19, DRV Pull-Dwn=0x19
[    1.245093] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2
[    1.322212] bio: create slab <bio-0> at 0
[    1.324100] Enter firefly_noatx8_init
[    1.324611] firefly_noatx8_probe 51
[    1.325367] SCSI subsystem initialized
[    1.325896] usbcore: registered new interface driver usbfs
[    1.326086] usbcore: registered new interface driver hub
[    1.326403] usbcore: registered new device driver usb
[    1.330897] rockchip_i2c ff650000.i2c: i2c-0: Rockchip I2C adapter
[    1.335359] rockchip_i2c ff140000.i2c: i2c-1: Rockchip I2C adapter
[    1.336872] rockchip_i2c ff660000.i2c: i2c-2: Rockchip I2C adapter
[    1.338466] rockchip_i2c ff150000.i2c: i2c-3: Rockchip I2C adapter
[    1.339340] rockchip_i2c ff160000.i2c: i2c-4: Rockchip I2C adapter
[    1.342263] media: Linux media interface: v0.10
[    1.342456] Linux video capture interface: v2.00
[    1.342648] pps_core: LinuxPPS API ver. 1 registered
[    1.342722] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.342859] PTP clock support registered
[    1.343310] rockchip_temp_probe,line=362
[    1.344130] tsadc ff280000.tsadc: initialized
[    1.345396] rockchip_ion_parse_dt: num_heaps = 1
[    1.345489] 0:  0  3  vmalloc  0x  (null)
[    1.346324] Rockchip ion module is successfully loaded (v1.0)
[    1.346892] Advanced Linux Sound Architecture Driver Initialized.
[    1.348265] Bluetooth: Core ver 2.16
[    1.348424] NET: Registered protocol family 31
[    1.348497] Bluetooth: HCI device and connection manager initialized
[    1.348593] Bluetooth: HCI socket layer initialized
[    1.348675] Bluetooth: L2CAP socket layer initialized
[    1.348799] Bluetooth: SCO socket layer initialized
[    1.349497] cfg80211: Calling CRDA to update world regulatory domain
[    1.351818] act8846_i2c_probe,line=898
[    1.353254] act8846_parse_dt,line=746
[    1.354814] act8846_i2c_probe: act8846_pmic_hold=1
[    1.354919] act8846_i2c_probe: act8846_pmic_sleep=1
[    1.355009] act8846_i2c_probe: act8846_pmic_cpu_det_gpio=1
[    1.355101] act8846_i2c_probe: act8846_pmic_usb_hub_reset_gpio=1
[    1.357634] act_dcdc1: 1200 mV
[    1.361416] vccio: 3300 mV
[    1.364073] vdd_logic: 700 <--> 1500 mV at 1100 mV
[    1.367885] act_dcdc4: 2000 mV
[    1.369764] vccio_sd: 1800 <--> 3300 mV at 3300 mV
[    1.372749] act_ldo2: 1050 mV
[    1.375666] act_ldo3: 2800 mV
[    1.378609] act_ldo4: 3300 mV
[    1.381522] act_ldo5: 3300 mV
[    1.384432] act_ldo6: 1100 mV
[    1.387380] vcc_18: 1800 mV
[    1.390363] act_ldo8: 1850 mV
[    1.396968] vdd_arm: 712 <--> 1500 mV at 1000 mV
[    1.403417] vdd_gpu: 712 <--> 1500 mV at 1000 mV
[    1.404399] rk808_i2c_probe,line=1368
[    1.406081] The device is not rk808 -11
[    1.406375] rk808: probe of 0-001b failed with error -11
[    1.408966] i2s: maxburst: 1
[    1.410888] Switching to clocksource arch_sys_counter
[    1.476831] rk-fb rockchip-fb: rk fb ion client create success!
[    1.476947] rk-fb rockchip-fb: rockchip framebuffer driver probe
[    1.478094] rk-screen rk_screen.9: rockchip screen probe success
[    1.478904] rk32-lvds rk32-lvds: rk32 lvds driver probe success
[    1.479700] rk32-edp ff970000.edp: screen is not edp!
[    1.479807] rk32-edp: probe of ff970000.edp failed with error -22
[    1.481047] rk3288-lcdc lcdc0: can't find power_ctr node for lcdc0
[    1.481789] graphics fb0: rockchip framebuffer registerd:fb0
[    1.482850] graphics fb1: rockchip framebuffer registerd:fb1
[    1.483438] graphics fb2: rockchip framebuffer registerd:fb2
[    1.484034] graphics fb3: rockchip framebuffer registerd:fb3
[    1.484620] graphics fb4: rockchip framebuffer registerd:fb4
[    1.486319] rk_iommu ff930300.vopb_mmu: (vopb) Enabled
[    1.486787] rk3288-lcdc lcdc0: lcdc0: dclk:148500000>>fps:60
[    1.486894] rk3288-lcdc lcdc0: wakeup from standby!
[    1.620814] alloc_buffer:ion_phy_addr=0x10000000
[    1.664182] fb0:phy:10000000>>vir:f0191000>>len:0x1800000
[    1.787773] rk3288-lcdc lcdc0: lcdc0 probe ok, iommu enabled
[    1.788976] rockchip_set_mux:warning ignore bank num 15
[    1.789459] rockchip_set_mux:warning ignore bank num 15
[    1.789888] rockchip_set_mux:warning ignore bank num 15
[    1.790323] rockchip_set_mux:warning ignore bank num 15
[    1.790753] rockchip_set_mux:warning ignore bank num 15
[    1.791168] rockchip_set_mux:warning ignore bank num 15
[    1.792111] rockchip_set_mux:warning ignore bank num 15
[    1.792695] rockchip_set_mux:warning ignore bank num 15
[    1.793572] rockchip_set_mux:warning ignore bank num 15
[    1.794102] rockchip_set_mux:warning ignore bank num 15
[    1.794975] rockchip_set_mux:warning ignore bank num 15
[    1.795503] rockchip_set_mux:warning ignore bank num 15
[    1.796383] rockchip_set_mux:warning ignore bank num 15
[    1.796915] rockchip_set_mux:warning ignore bank num 15
[    1.820392] NET: Registered protocol family 2
[    1.821917] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    1.822448] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    1.822980] TCP: Hash tables configured (established 8192 bind 8192)
[    1.823169] TCP: reno registered
[    1.823245] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    1.823408] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    1.824083] NET: Registered protocol family 1
[    1.824839] Unpacking initramfs...
[    2.333091] Freeing initrd memory: 2520K (c4bf0000 - c4e66000)
[    2.334794] hw perfevents: enabled with ARMv7 Cortex-A12 PMU driver, 7 counters available
[    2.336360] probe device ff9a0000.vpu_service
[    2.336832] vpu_service: power on
[    2.338015] checking hw id 4831
[    2.339143] vpu_service set to auto frequency mode
[    2.339345] vcodec vpu_service: vcodec ion client create success!
[    2.340470] vpu_service: power off...
[    2.340583] done
[    2.340647] init success
[    2.340828] probe device ff9c0000.hevc_service
[    2.341451] hevc_service: power on
[    2.342618] checking hw id 6867
[    2.343482] vcodec hevc_service: vcodec ion client create success!
[    2.344406] hevc_service: power off...
[    2.344518] done
[    2.344580] init success
[    2.344943] rknandbase v1.0 2014-03-31
[    2.345588] rknand_probe clk rate = 148500000
[    2.346073] rknand_driver:ret = 0
[    2.347235] audit: initializing netlink socket (disabled)
[    2.347386] type=2000 audit(1.330:1): initialized
[    2.350152] bounce pool size: 64 pages
[    2.365834] fuse init (API version 7.22)
[    2.367146] msgmni has been set to 1424
[    2.373222] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[    2.373338] io scheduler noop registered
[    2.373404] io scheduler deadline registered
[    2.373780] io scheduler cfq registered (default)
[    2.375213] Console: switching to colour frame buffer device 240x67
[    2.425645] rga ff920000.rga: rga ion client create success!
[    2.426320] rga: Driver loaded succesfully
[    2.427949] IEP Power ON
[    2.428188] iep ion client create success!
[    2.429349] rk_iommu ff900800.iep_mmu: (iep) Enabled
[    2.429652] IEP Power OFF
[    2.429814] rk_iommu ff900800.iep_mmu: (iep) Disabled
[    2.430072] rk_iommu ff900800.iep_mmu: rockchip_iommu_detach_device: Detached IOMMU with pgtable 0x2e26a000
[    2.430511] IEP Driver loaded succesfully
[    2.430968] Module initialized.
[    2.433617] dma-pl330 ffb20000.pdma: Loaded driver for PL330 DMAC-2364208
[    2.433971] dma-pl330 ffb20000.pdma:         DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10
[    2.438686] dma-pl330 ff250000.pdma: Loaded driver for PL330 DMAC-2364208
[    2.439040] dma-pl330 ff250000.pdma:         DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[    2.440142] pwm-voltage-regulator pwm_regulator.23: unable to request PWM, trying legacy API
[    2.440546] pwm-voltage-regulator pwm_regulator.23: unable to request legacy PWM
[    2.440877] pwm_regulator_probe:error
[    2.441102] platform pwm_regulator.23: Driver pwm-voltage-regulator requests probe deferral
[    2.442496] rk_serial.c v1.8 2014-03-04
[    2.443300] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 87) is a rk29_serial.0
[    2.444332] serial ff180000.serial: membase f0172000
[    2.454232] loop: module loaded
[    2.456213] SCSI Media Changer driver v0.25
[    2.457430] tun: Universal TUN/TAP device driver, 1.6
[    2.457693] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    2.459643] stmmac_probe_config_dt: Can not read property: pmu_regulator.
[    2.459982] stmmac_probe_config_dt: Can not read property: pmu_enable_level.
[    2.460307] stmmac_probe_config_dt: clock input or output? (input).
[    2.460598] stmmac_probe_config_dt: TX delay(0x30).
[    2.460833] stmmac_probe_config_dt: RX delay(0x20).
[    2.461151] stmmac_probe_config_dt: is rockchip,rk3288-gmac
[    2.461411] stmmc_pltfr_init:
[    2.461589] stmmc_pltfr_init: ERROR: Get power-gpio failed.
[    2.461885] stmmc_pltfr_init: ERROR: Request gmac phy reset pin failed.
[    2.462182] stmmc_pltfr_init: init for RGMII
[    2.462393] tx delay=0x30
[    2.462393] rx delay=0x20
[    2.474087] stmmac - user ID: 0x10, Synopsys ID: 0x35
[    2.484333]  Normal descriptors
[    2.494507]  Ring mode enabled
[    2.504672]  DMA HW capability register supported
[    2.504905]  RX Checksum Offload Engine supported (type 2)
[    2.525086]  TX Checksum insertion supported
[    2.535193]  Wake-Up On Lan supported
[    2.545446]  Enable RX Mitigation via HW Watchdog Timer
[    2.556940] PPP generic driver version 2.4.2
[    2.567732] PPP BSD Compression module registered
[    2.578065] PPP Deflate Compression module registered
[    2.588465] PPP MPPE Compression module registered
[    2.598765] NET: Registered protocol family 24
[    2.609056] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[    2.619697] CSLIP: code copyright 1989 Regents of the University of California.
[    2.630487] Rockchip WiFi SYS interface (V1.00) ...
[    2.641511] usbcore: registered new interface driver catc
[    2.652520] usbcore: registered new interface driver kaweth
[    2.663374] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[    2.674456] usbcore: registered new interface driver pegasus
[    2.685543] usbcore: registered new interface driver rtl8150
[    2.696547] usbcore: registered new interface driver r8152
[    2.707371] hso: drivers/net/usb/hso.c: Option Wireless
[    2.718433] usbcore: registered new interface driver hso
[    2.729376] usbcore: registered new interface driver asix
[    2.740085] usbcore: registered new interface driver ax88179_178a
[    2.750763] usbcore: registered new interface driver cdc_ether
[    2.761488] usbcore: registered new interface driver cdc_eem
[    2.772077] usbcore: registered new interface driver dm9601
[    2.782544] usbcore: registered new interface driver dm9620
[    2.792866] usbcore: registered new interface driver smsc75xx
[    2.803126] usbcore: registered new interface driver smsc95xx
[    2.813245] usbcore: registered new interface driver gl620a
[    2.823290] usbcore: registered new interface driver net1080
[    2.833246] usbcore: registered new interface driver plusb
[    2.843114] usbcore: registered new interface driver rndis_host
[    2.852908] usbcore: registered new interface driver cdc_subset
[    2.862521] usbcore: registered new interface driver zaurus
[    2.871887] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[    2.881368] usbcore: registered new interface driver int51x1
[    2.890649] usbcore: registered new interface driver kalmia
[    2.899798] usbcore: registered new interface driver ipheth
[    2.908820] usbcore: registered new interface driver sierra_net
[    2.917727] usbcore: registered new interface driver cx82310_eth
[    2.926459] usbcore: registered new interface driver cdc_ncm
[    2.935079] usbcore: registered new interface driver qmi_wwan
[    2.943573] usbcore: registered new interface driver cdc_mbim
[    2.951765] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.963266] EHCI: ehci_rk_probe f1a00000 f1a00010
[    2.971470] rockchip_ehci_host ff500000.usb: EHCI Host Controller
[    2.979697] rockchip_ehci_host ff500000.usb: new USB bus registered, assigned bus number 1
[    2.988978] rockchip_ehci_host ff500000.usb: irq 56, io mem 0xff500000
[    3.015072] rockchip_ehci_host ff500000.usb: USB 2.0 started, EHCI 1.00
[    3.023334] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    3.031514] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.039640] usb usb1: Product: EHCI Host Controller
[    3.047792] usb usb1: Manufacturer: Linux 3.10.0 ehci_hcd
[    3.055969] usb usb1: SerialNumber: ff500000.usb
[    3.065422] hub 1-0:1.0: USB hub found
[    3.073748] hub 1-0:1.0: 1 port detected
[    3.082591] EHCI: ehci_rk_probe ok
[    3.091196] usbcore: registered new interface driver cdc_acm
[    3.099494] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    3.108145] usbcore: registered new interface driver usblp
[    3.116784] usbcore: registered new interface driver cdc_wdm
[    3.125436] usbcore: registered new interface driver usb-storage
[    3.134043] usbcore: registered new interface driver ums-alauda
[    3.142506] usbcore: registered new interface driver ums-cypress
[    3.150920] usbcore: registered new interface driver ums-datafab
[    3.159343] usbcore: registered new interface driver ums_eneub6250
[    3.167668] usbcore: registered new interface driver ums-freecom
[    3.176041] usbcore: registered new interface driver ums-isd200
[    3.184220] usbcore: registered new interface driver ums-jumpshot
[    3.192324] usbcore: registered new interface driver ums-karma
[    3.200275] usbcore: registered new interface driver ums-onetouch
[    3.208172] usbcore: registered new interface driver ums-sddr09
[    3.215987] usbcore: registered new interface driver ums-sddr55
[    3.223696] usbcore: registered new interface driver ums-usbat
[    3.231434] usbcore: registered new interface driver usbserial
[    3.238989] usbcore: registered new interface driver usbserial_generic
[    3.246297] usbserial: USB Serial support registered for generic
[    3.253506] usbcore: registered new interface driver option
[    3.260566] usbserial: USB Serial support registered for GSM modem (1-port)
[    3.267958] usbcore: registered new interface driver trancevibrator
[    3.275207] usb20_otg: version 3.10a 21-DEC-2012
[    3.283459] f1a80040
[    3.290473] Core Release: 3.10a
[    3.297577] Setting default values for core params
[    3.305179] Using Buffer DMA mode
[    3.312392] Periodic Transfer Interrupt Enhancement - disabled
[    3.319575] Multiprocessor Interrupt Enhancement - disabled
[    3.326891] OTG VER PARAM: 0, OTG VER FLAG: 0
[    3.334262] ^^^^^^^^^^^^^^^^^Device Mode
[    3.341684] Dedicated Tx FIFOs mode
[    3.349138] pcd_init otg_dev = ed971800
[    3.357152] usb20_otg ff580000.usb: DWC OTG Controller
[    3.364935] usb20_otg ff580000.usb: new USB bus registered, assigned bus number 2
[    3.372906] usb20_otg ff580000.usb: irq 55, io mem 0x00000000
[    3.381014] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    3.389191] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.397431] usb usb2: Product: DWC OTG Controller
[    3.405743] usb usb2: Manufacturer: Linux 3.10.0 dwc_otg_hcd
[    3.414182] usb usb2: SerialNumber: ff580000.usb
[    3.423925] hub 2-0:1.0: USB hub found
[    3.432492] hub 2-0:1.0: 1 port detected
[    3.441966] usb20_host: version 3.10a 21-DEC-2012
[    3.454165] f1b00040
[    3.462809] Core Release: 3.10a
[    3.471511] Setting default values for core params
[    3.480659] Using Buffer DMA mode
[    3.489430] Periodic Transfer Interrupt Enhancement - disabled
[    3.498388] Multiprocessor Interrupt Enhancement - disabled
[    3.507482] OTG VER PARAM: 0, OTG VER FLAG: 0
[    3.516588] ^^^^^^^^^^^^^^^^^^Host Mode
[    3.525694] usb20_host ff540000.usb: DWC OTG Controller
[    3.534832] usb20_host ff540000.usb: new USB bus registered, assigned bus number 3
[    3.544178] usb20_host ff540000.usb: irq 57, io mem 0x00000000
[    3.553443] Init: Power Port (0)
[    3.562628] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    3.571939] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.581151] usb usb3: Product: DWC OTG Controller
[    3.590308] usb usb3: Manufacturer: Linux 3.10.0 dwc_otg_hcd
[    3.599448] usb usb3: SerialNumber: ff540000.usb
[    3.609819] hub 3-0:1.0: USB hub found
[    3.618972] hub 3-0:1.0: 1 port detected
[    3.630020] .. rk pwm remotectl v1.0 init
[    3.639461] remotectl probe j=0x0
[    3.649006] input: ff680000.pwm as /devices/ff680000.pwm/input/input0
[    3.658791] pwm enable val=0x646205
[    3.668661] usbcore: registered new interface driver xpad
[    3.677826] usbcore: registered new interface driver usb_acecad
[    3.687002] usbcore: registered new interface driver aiptek
[    3.696157] usbcore: registered new interface driver gtco
[    3.705294] usbcore: registered new interface driver hanwang
[    3.714458] usbcore: registered new interface driver kbtab
[    3.723762] usbcore: registered new interface driver wacom
[    3.733851] sensor_register_slave:mma8452,id=17
[    3.742893] sensor_register_slave:cm3217,id=44
[    3.751999] sensor_register_slave:cm3218,id=45
[    3.752035] tchip_rm_init is here!
[    3.753584] input: tchip_remote_key as /devices/virtual/input/input1
[    3.753960] tchiprm_register_device is here!
[    3.754367] input: tchip_remote_touch as /devices/virtual/input/input2
[    3.754720] tchip_remote_abs_register_device is here!
[    3.755099] input: tchip_remote_gsensor as /devices/virtual/input/input3
[    3.755440] tchip_remote_gsensor_register_device is here!
[    3.758878] rtc_hym8563 0-0051: clock/calendar information is no longer guaranteed
[    3.763062] rtc_hym8563 0-0051: rtc core: registered hym8563 as rtc0
[    3.763219] i2c /dev entries driver
[    3.765486] IR NEC protocol handler initialized
[    3.765509] IR RC5(x) protocol handler initialized
[    3.765527] IR RC6 protocol handler initialized
[    3.765544] IR JVC protocol handler initialized
[    3.765561] IR Sony protocol handler initialized
[    3.765578] IR RC5 (streamzap) protocol handler initialized
[    3.765595] IR SANYO protocol handler initialized
[    3.765612] IR MCE Keyboard/mouse protocol handler initialized
[    3.765847] usbcore: registered new interface driver uvcvideo
[    3.765867] USB Video Class driver (1.1.1)
[    3.765896] CamSys driver version: v0.19.0,  CamSys head file version: v0.8.0
[    3.769140] D1:camsys_platform_probe(1061): 1-gpios-cifpower: gpio=236
[    3.769190] D1:camsys_platform_probe(1064): gpios-cifpower: gpio_request
[    3.769232] D1:camsys_platform_probe(1066): 1-gpios-cifpower: gpio_request=0
[    3.769272] D1:camsys_platform_probe(1075): gpios-cifpower: 236 high
[    3.769470] D1:camsys_mipiphy_probe_cb(163): ff910000.isp mipi phy0 probe success(reg_phy: 0x0  reg_vir: 0x0  size: 0x0)
[    3.769909] D1:camsys_mipiphy_probe_cb(160): ff910000.isp mipi phy1 probe success(reg_phy: 0xff968000  reg_vir: 0xf19b0000  size: 0x4000)
[    3.771993] D1:camsys_platform_probe(1208): ff910000.isp memory:
[    3.772030] D1:camsys_platform_probe(1218):     Register memory (phy: 0xff910000 vir: 0xf19e0000 size: 0x10000)
[    3.772061] D1:camsys_platform_probe(1213):     I2c memory (phy: 0x2da1d000 vir: 0xeda1d000 size: 0x1000)
[    3.772086] D1:camsys_platform_probe(1233): Probe ff910000.isp device success
[    3.775055] device-mapper: uevent: version 1.0.3
[    3.775771] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[    3.776668] Bluetooth: HCI UART driver ver 2.2
[    3.776696] Bluetooth: HCI H4 protocol initialized
[    3.776717] Bluetooth: HCILL protocol initialized
[    3.782526] cpufreq version 1.0, suspend freq 1200 MHz
[    3.783091] cpuidle: using governor ladder
[    3.783114] cpuidle: using governor menu
[    3.783230] Synopsys Designware Multimedia Card Interface Driver
[    3.783967] dwmmc_rockchip ff0f0000.rksdmmc: Version ID is 270a
[    3.798934] dwmmc_rockchip ff0f0000.rksdmmc: Using internal DMA controller.
[    3.799406] 3291..dw_mci_init_slot: fmin=400000, fmax=100000000 [mmc0]
[    3.799431] mmc0 : Rockchip specific MHSC: Ver 1.13 2014-09-05
[    3.799777] 1381..dw_mci_set_ios:  no card. [mmc0]
[    3.812049] 1381..dw_mci_set_ios:  no card. [mmc0]
[    3.831806] dwmmc_rockchip ff0f0000.rksdmmc: DW MMC controller at irq 67, 32 bit host data width, 256 deep fifo
[    3.831819] dwmmc_rockchip ff0f0000.rksdmmc: 1 slots initialized
[    3.831863] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out 800000Hz for init[mmc0]
[    3.832163] dwmmc_rockchip ff0c0000.rksdmmc: Version ID is 270a
[    3.838084] dwmmc_rockchip ff0c0000.rksdmmc: Using internal DMA controller.
[    3.838266] 3285..dw_mci_init_slot: fmin=300000, fmax=50000000 [mmc1]
[    3.838273] mmc1 : Rockchip specific MHSC: Ver 1.13 2014-09-05
[    3.838720] 1381..dw_mci_set_ios:  no card. [mmc1]
[    3.851449] 1381..dw_mci_set_ios:  no card. [mmc1]
[    3.863889] mmc0: BKOPS_EN bit is not set
[    3.865771] rk_sdmmc: BOOT Bus speed=0Hz,Bus width=8bits.[mmc0]
[    3.868057] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0)
[    3.868075] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out normal clock [mmc0]
[    3.871178] dwmmc_rockchip ff0c0000.rksdmmc: DW MMC controller at irq 64, 32 bit host data width, 256 deep fifo
[    3.871186] dwmmc_rockchip ff0c0000.rksdmmc: 1 slots initialized
[    3.871432] dwmmc_rockchip ff0d0000.rksdmmc: Version ID is 270a
[    3.875082] dwmmc_rockchip ff0d0000.rksdmmc: Using internal DMA controller.
[    3.875211] 3291..dw_mci_init_slot: fmin=200000, fmax=50000000 [mmc2]
[    3.875215] mmc2 : Rockchip specific MHSC: Ver 1.13 2014-09-05
[    3.875287] 1381..dw_mci_set_ios:  no card. [mmc2]
[    3.882973] rk_sdmmc: BOOT
[    3.882973]  execute tuning: candidates_degree = SDMMC_SHIFT_DEGREE_0        SDMMC_SHIFT_DEGREE_90   SDMMC_SHIFT_DEGREE_180  SDMMC_SHIFT_DEGREE_INVALID[mmc0]
[    3.883020] mmc0: new HS200 MMC card at address 0001
[    3.883267] mmcblk0: mmc0:0001 BWBC3R 29.1 GiB
[    3.883559] mtd: partition size too small (7)
[    3.883569]   resource: 0x000400000 -- 0x001400000 (16 MB)
[    3.883575]       boot: 0x001400000 -- 0x002400000 (16 MB)
[    3.883581]       misc: 0x002400000 -- 0x002800000 (4 MB)
[    3.883586]     backup: 0x002800000 -- 0x005c00000 (52 MB)
[    3.883592]  linuxroot: 0x005c00000 -- 0x747800000 (29724 MB)
[    3.884184]  mmcblk0: p1 p2 p3 p4 p51381..dw_mci_set_ios:  no card. [mmc1]
[    3.890756] 1381..dw_mci_set_ios:  no card. [mmc2]
[    3.910428] 1381..dw_mci_set_ios:  no card. [mmc2]
[    3.910616] dwmmc_rockchip ff0d0000.rksdmmc: DW MMC controller at irq 65, 32 bit host data width, 256 deep fifo
[    3.910622] dwmmc_rockchip ff0d0000.rksdmmc: 1 slots initialized
[    3.910857] leds-gpio leds.31: pins are not configured from the driver
[    3.911066] hidraw: raw HID events driver (C) Jiri Kosina
[    3.912363] usbcore: registered new interface driver usbhid
[    3.912368] usbhid: USB HID core driver
[    3.912680] ashmem: initialized
[    3.912781] logger: created 256K log 'log_main'
[    3.912867] logger: created 256K log 'log_events'
[    3.912951] logger: created 256K log 'log_radio'
[    3.913045] logger: created 256K log 'log_system'
[    3.914016] input: rk29-keypad as /devices/ff100000.adc/key.34/input/input4
[    3.914616] rockchip-pinctrl ff770000.pinctrl: pin gpio6-8 already requested by ; cannot claim for 2-0010
[    3.914624] rockchip-pinctrl ff770000.pinctrl: pin-200 (2-0010) status -22
[    3.914632] rockchip-pinctrl ff770000.pinctrl: could not request pin 200 on device rockchip-pinctrl
[    3.914639] ES8323 2-0010: Error applying setting, reverse things back
[    3.914914] es8323 probe i2c recv ok
[    3.915132] i2c-core: driver [ES8323] using legacy suspend method
[    3.915136] i2c-core: driver [ES8323] using legacy resume method
[    3.915430] rockchip-hdmi-spdif rockchip-hdmi-spdif.27: ASoC: CPU DAI (null) not registered
[    3.915456] rockchip_hdmi_spdif_audio_probe() register card failed:-517
[    3.915470] platform rockchip-hdmi-spdif.27: Driver rockchip-hdmi-spdif requests probe deferral
[    3.915676] es8323_probe
[    3.915755] es8323_probe:register ISR (irq=194)
[    4.550393] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> NULL --> Left Line Mux
[    4.552590] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> NULL -> Left Line Mux
[    4.554791] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> NULL --> Left Line Mux
[    4.556970] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> NULL -> Left Line Mux
[    4.559137] ES8323 2-0010: ASoC: no dapm match for Left PGA Mux --> NULL --> Left Line Mux
[    4.561329] ES8323 2-0010: ASoC: Failed to add route Left PGA Mux -> NULL -> Left Line Mux
[    4.563504] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> NULL --> Right Line Mux
[    4.565662] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> NULL -> Right Line Mux
[    4.567838] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> NULL --> Right Line Mux
[    4.570008] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> NULL -> Right Line Mux
[    4.572160] ES8323 2-0010: ASoC: no dapm match for Right PGA Mux --> NULL --> Right Line Mux
[    4.574311] ES8323 2-0010: ASoC: Failed to add route Right PGA Mux -> NULL -> Right Line Mux
[    4.576443] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> LAMP --> Left PGA Mux
[    4.578560] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> LAMP -> Left PGA Mux
[    4.580678] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> LAMP --> Left PGA Mux
[    4.582753] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> LAMP -> Left PGA Mux
[    4.584825] ES8323 2-0010: ASoC: no dapm match for Differential Mux --> LAMP --> Left PGA Mux
[    4.586875] ES8323 2-0010: ASoC: Failed to add route Differential Mux -> LAMP -> Left PGA Mux
[    4.588970] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> RAMP --> Right PGA Mux
[    4.591050] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> RAMP -> Right PGA Mux
[    4.593124] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> RAMP --> Right PGA Mux
[    4.595168] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> RAMP -> Right PGA Mux
[    4.597170] ES8323 2-0010: ASoC: no dapm match for Differential Mux --> RAMP --> Right PGA Mux
[    4.599155] ES8323 2-0010: ASoC: Failed to add route Differential Mux -> RAMP -> Right PGA Mux
[    4.601130] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> LAMP --> Differential Mux
[    4.603123] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> LAMP -> Differential Mux
[    4.605122] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> RAMP --> Differential Mux
[    4.607116] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> RAMP -> Differential Mux
[    4.609086] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> LAMP --> Differential Mux
[    4.611022] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> LAMP -> Differential Mux
[    4.612972] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> RAMP --> Differential Mux
[    4.614865] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> RAMP -> Differential Mux
[    4.616705] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> LAMP --> Left Line Mux
[    4.618511] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> LAMP -> Left Line Mux
[    4.620322] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> LAMP --> Left Line Mux
[    4.622123] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> LAMP -> Left Line Mux
[    4.623932] ES8323 2-0010: ASoC: no dapm match for Left PGA Mux --> LAMP --> Left Line Mux
[    4.625768] ES8323 2-0010: ASoC: Failed to add route Left PGA Mux -> LAMP -> Left Line Mux
[    4.627610] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> RAMP --> Right Line Mux
[    4.629469] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> RAMP -> Right Line Mux
[    4.631320] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> RAMP --> Right Line Mux
[    4.633139] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> RAMP -> Right Line Mux
[    4.634992] ES8323 2-0010: ASoC: no dapm match for Right PGA Mux --> RAMP --> Right Line Mux
[    4.636847] ES8323 2-0010: ASoC: Failed to add route Right PGA Mux -> RAMP -> Right Line Mux
[    4.638806] ES8323 2-0010: ASoC: mux Right Line Mux has no paths
[    4.640657] ES8323 2-0010: ASoC: mux Left Line Mux has no paths
[    4.642453] ES8323 2-0010: ASoC: mux Right PGA Mux has no paths
[    4.644219] ES8323 2-0010: ASoC: mux Left PGA Mux has no paths
[    4.645986] ES8323 2-0010: ASoC: mux Differential Mux has no paths
[    4.650589] Enter::rk29_es8323_init----135
[    4.655577] rockchip-es8323 rockchip-es8323.29:  ES8323 HiFi <-> rockchip-i2s.0 mapping ok
[    4.657911] u32 classifier
[    4.659766]     Actions configured
[    4.661593] Netfilter messages via NETLINK v0.30.
[    4.663442] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[    4.665527] ctnetlink v0.93: registering with nfnetlink.
[    4.667404] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[    4.669249] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[    4.671244] xt_time: kernel timezone is -0000
[    4.673186] ip_tables: (C) 2000-2006 Netfilter Core Team
[    4.675095] arp_tables: (C) 2002 David S. Miller
[    4.676922] TCP: cubic registered
[    4.678711] Initializing XFRM netlink socket
[    4.680646] NET: Registered protocol family 10
[    4.682784] mip6: Mobile IPv6
[    4.684498] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    4.686300] sit: IPv6 over IPv4 tunneling driver
[    4.688314] NET: Registered protocol family 17
[    4.690026] NET: Registered protocol family 15
[    4.691747] Bridge firewalling registered
[    4.693440] Ebtables v2.0 registered
[    4.695274] Bluetooth: RFCOMM TTY layer initialized
[    4.696984] Bluetooth: RFCOMM socket layer initialized
[    4.698681] Bluetooth: RFCOMM ver 1.11
[    4.700355] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    4.702055] Bluetooth: BNEP filters: protocol multicast
[    4.703774] Bluetooth: BNEP socket layer initialized
[    4.705464] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    4.707153] Bluetooth: HIDP socket layer initialized
[    4.708841] l2tp_core: L2TP core driver, V2.0
[    4.710504] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[    4.712170] [WLAN_RFKILL]: Enter rfkill_wlan_init
[    4.714060] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[    4.715728] wlan_platdata_parse_dt: wifi_chip_type = bcmwifi
[    4.717412] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[    4.719083] [WLAN_RFKILL]: wlan_platdata_parse_dt: disable wifi io reference voltage control.
[    4.720760] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[    4.722468] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,poweren_gpio = 156, flags = 0.
[    4.724204] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 158, flags = 0.
[    4.725898] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[    4.727635] [WLAN_RFKILL]: rockchip_wifi_voltage_select: wifi & sdio reference voltage: 1.8V
[    4.729419] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[    4.731184] [BT_RFKILL]: Enter rfkill_rk_init
[    4.733032] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 147.
[    4.734812] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,power_gpio = 155.
[    4.736609] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 157.
[    4.738411] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 154.
[    4.740200] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 159.
[    4.742024] [BT_RFKILL]: Request irq for bt wakeup host
[    4.743873] [BT_RFKILL]: ** disable irq
[    4.745693] [BT_RFKILL]: ap6335 device registered.
[    4.748044] rk3288-hdmi ff980000.hdmi: rk3288 hdmi probe sucess.
[    4.750148] VFP support v0.3: implementor 41 architecture 3 part 30 variant d rev 0
[    4.751952] rk3288_init_suspend
[    4.753729] rk3288_suspend_init enter
[    4.755593] rk3288_suspend_init: pm_ctrbits =40017
[    4.757391] gpio_get_dts_info suspend:8
[    4.759164] gpio_get_dts_info resume:8
[    4.760902] rockchip,pmic-suspend_gpios:1007c30 1007c40 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
[    4.762756] rockchip,pmic-resume_gpios:2007c32 2007c42 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
[    4.764716] clks_gating_suspend_init:clkgt info ok
[    4.766562] Registering SWP/SWPB emulation handler
[    4.768651] ddrfreq: verion 1.2 20140526
[    4.770616] ddrfreq: normal 456MHz video_1080p 0MHz video_4k 456MHz dualview 0MHz idle 0MHz suspend 200MHz reboot 456MHz
[    4.772083] ddrfreq: auto-freq=0
[    4.773525] ddrfreq: auto-freq-table[0] 240MHz
[    4.774953] ddrfreq: auto-freq-table[1] 324MHz
[    4.776363] ddrfreq: auto-freq-table[2] 456MHz
[    4.777737] ddrfreq: auto-freq-table[3] 528MHz
[    4.779542] act_ldo3: operation not allowed
[    4.781147] vga_edid_probe: turn on ldo3 done.
[    4.782534] act_ldo4: operation not allowed
[    4.784121] vga_edid_probe: turn on ldo done.
[    4.785484] act_ldo2: operation not allowed
[    4.787070] vga_edid_probe: turn on ldo2 done.
[    4.788427] act_ldo8: operation not allowed
[    4.789985] vga_edid_probe: turn on ldo done.
[    4.816386] vga-ddc: read and parse vga edid success.
[    4.817714] vga-ddc: max mode 1920x1080@60[pixclock-148500 KHZ]
[    4.819054] vga-ddc: best mode 1920x1080@60[pixclock-6 KHZ]
[    4.820388] vga_edid_probe: success. 10
[    4.821848] firefly_vga_get_enable 180, 0
[    4.823176] firefly_vga_get_status 186
[    4.824496] firefly_vga_set_enable 159 enable:1
[    4.825827] firefly_vga_enable 130 start
[    4.825843] regulator-dummy: disabling
[    4.826115] rockchip-hdmi-spdif rockchip-hdmi-spdif.27: ASoC: CPU DAI (null) not registered
[    4.826132] rockchip_hdmi_spdif_audio_probe() register card failed:-517
[    4.826142] platform rockchip-hdmi-spdif.27: Driver rockchip-hdmi-spdif requests probe deferral
[    4.826215] pcd_pullup, is_on 0
[    4.826245] file system registered
[    4.826734] android_usb gadget: Mass Storage Function, version: 2009/09/11
[    4.826738] android_usb gadget: Number of LUNs=2
[    4.826743]  lun0: LUN: removable file: (no medium)
[    4.826746]  lun1: LUN: removable file: (no medium)
[    4.826882] android_usb gadget: android_usb ready
[    4.826954] sensor_init: Probe name sensors
[    4.826966] sensor-dev.c v1.4 add angle calculation support between two gsensors 2013-09-01
[    4.845068] rtc_hym8563 0-0051: setting system clock to 2011-01-01 12:00:01 UTC (1293883201)
[    4.845072] firefly_switch_fb 55
[    4.845077]
[    4.845077] rk_fb_switch_screen lcdc_id 0 type 1 enable 1
[    4.845083] fb0 win id 1 state 1
[    4.845095] rk3288-lcdc lcdc0: lcdc0: dclk:148500000>>fps:60
[    4.845113] fb1 win id 0 state 0
[    4.845117] fb2 win id 2 state 0
[    4.845119] fb3 win id 3 state 0
[    4.845122] fb4 win id 4 state 0
[    4.845125]
[    4.845125] rk_fb_switch_screen lcdc_id 0 type 1 enable 1 done
[    4.845125]
[    4.845145] VGA ENABLE
[    4.870000] usbcore: registered new interface driver snd-usb-audio
[    4.871429] ALSA device list:
[    4.872837]   #0: RK_ES8323
[    4.873927] rockchip-hdmi-spdif rockchip-hdmi-spdif.27:  rk-hdmi-spdif-hifi <-> rockchip-spdif mapping ok
[    4.875916]   #1: RK-HDMI-SPDIF
[    4.878315] Freeing unused kernel memory: 2368K (c0a9c000 - c0cec000)
[    4.901115] udevd[147]: starting version 175
[    5.051872] EHCI: rk_ehci_hcd_enable, disable host controller
[    5.079340] EXT4-fs (mmcblk0p5): recovery complete
[    5.081436] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null)
[    5.262888] init: plymouth-upstart-bridge main process (309) terminated with status 1
[    5.264762] init: plymouth-upstart-bridge main process ended, respawning
[    5.281837] init: plymouth-upstart-bridge main process (319) terminated with status 1
[    5.283699] init: plymouth-upstart-bridge main process ended, respawning
[    5.286563] init: ureadahead main process (312) terminated with status 5
[    5.302352] init: plymouth-upstart-bridge main process (323) terminated with status 1
[    5.304147] init: plymouth-upstart-bridge main process ended, respawning
[    5.397683] init: mounted-proc main process (336) terminated with status 1
[    5.453025] vga-ddc: read and parse vga edid success.
[    5.455252] vga-ddc: max mode 1920x1080@60[pixclock-148500 KHZ]
[    5.457497] vga-ddc: best mode 1920x1080@60[pixclock-6 KHZ]
[    5.459586] VGA Devie connected 10
[    5.461690] firefly_vga_set_mode 203
[    5.463899] firefly_vga_set_mode 219 1920 1080 60 148500000
[    5.466604] firefly_vga_enable 130 start
[    5.468694] firefly_switch_fb 55
[    5.470364]
[    5.470364] rk_fb_switch_screen lcdc_id 0 type 1 enable 1
[    5.473808] fb0 win id 1 state 1
[    5.476907] rk3288-lcdc lcdc0: lcdc0: dclk:148500000>>fps:60
[    5.479165] fb1 win id 0 state 0
[    5.481261] fb2 win id 2 state 0
[    5.483324] fb3 win id 3 state 0
[    5.489161] fb4 win id 4 state 0
[    5.491344]
[    5.491344] rk_fb_switch_screen lcdc_id 0 type 1 enable 1 done
[    5.491344]
* Starting Mount filesystems on boot[ OK ]
* Starting Signal sysvinit that the rootfs is mounted[ OK ]
* Starting Populate /dev filesystem[ OK ]
* Starting Populate and link to /run filesystem[ OK ]
* Stopping Populate /dev filesystem[ OK ]
* Stopping Populate and link to /run filesystem[ OK ]
* Stopping Track if upstart is running in a container[ OK ]
* Starting Clean /tmp directory[ OK ]
* Starting Initialize or finalize resolvconf[ OK ]
* Stopping Clean /tmp directory[ OK ]
* Starting Signal sysvinit that virtual filesystems are mounted[ OK ]
* Starting Signal sysvinit that virtual filesystems are mounted[ OK ]
* Starting Bridge udev events into upstart[ OK ]
* Starting Signal sysvinit that remote filesystems are mounted[ OK ]
* Starting device node and kernel event manager[ OK ]
* Starting Signal sysvinit that local filesystems are mounted[ OK ]
* Starting restore software rfkill state[ OK ]
* Stopping Mount filesystems on boot[ OK ]
* Stopping restore software rfkill state[ OK ]
* Starting flush early job output to logs[ OK ]
* Starting load modules from /etc/modules[ OK ]
* Starting cold plug devices[ OK ]
* Starting log initial device creation[ OK ]
* Stopping load modules from /etc/modules[ OK ]
* Stopping flush early job output to logs[ OK ]
* Starting D-Bus system message bus[ OK ]
* Starting set console font[ OK ]
* Starting SystemD login management service[ OK ]
* Stopping set console font[ OK ]
* Starting userspace bootsplash[ OK ]
* Starting system logging daemon[ OK ]
* Starting Send an event to indicate plymouth is up[ OK ]
* Stopping Send an event to indicate plymouth is up[ OK ]
* Starting configure network device security[ OK ]
* Starting configure network device[ OK ]
* Starting bluetooth initialization[ OK ]
* Starting bluetooth initialization[fail]
* Stopping userspace bootsplash[ OK ]
* Starting bluetooth daemon[ OK ]
* Starting configure network device security[ OK ]
* Starting configure network device security[ OK ]
* Starting configure network device[ OK ]
* Starting Mount network filesystems[ OK ]
* Starting Failsafe Boot Delay[ OK ]
* Stopping Mount network filesystems[ OK ]
* Starting Turn on/off the ap6335 bluetooth[ OK ]
* Starting configure network device[ OK ]
* Stopping Failsafe Boot Delay[ OK ]
* Starting System V initialisation compatibility[ OK ]
* Starting configure network device security[ OK ]
[ OK ]ting up X socket directories...        
* Starting Bridge file events into upstart[ OK ]
* Stopping System V initialisation compatibility[ OK ]
* Starting System V runlevel compatibility[ OK ]
* Starting Restore Sound Card State[ OK ]
* Starting save kernel messages[ OK ]
* Starting configure network device security[ OK ]
* Starting OpenSSH server[ OK ]
* Starting anac(h)ronistic cron[ OK ]
* Starting regular background program processing daemon[ OK ]
* Stopping save kernel messages[ OK ]
* Stopping Restore Sound Card State[ OK ]
* Starting Bridge socket events into upstart[ OK ]
* Starting configure virtual network devices[ OK ]
[    6.900374] turn on mali power
* Stopping System V runlevel compatibility[ OK ]
* Stopping Restore Sound Card State[ OK ]

在有时候卡在Stopping System V runlevel compatibility[ OK ],有时候卡在* Stopping Restore Sound Card State[ OK ],就一直卡住不动了,不知道是出了什么问题?
回复

使用道具 举报

164

积分

0

威望

0

贡献

技术小白

积分
164
发表于 2016-8-11 09:52:21     
mlt911213 发表于 2016-8-10 14:45
我觉得主要问题是:
mount: mounting /dev on /root/dev failed: No such file or directory
done.

哦,已经解决了,是ttyFIQ的问题。
能解释下ttyFIQ是什么东西吗?为什么要开启?怎么用ttyFIQ?
回复

使用道具 举报

600

积分

21

威望

25

贡献

技术大神

Rank: 3Rank: 3

积分
600

活跃会员

发表于 2016-8-16 09:25:52     
mlt911213 发表于 2016-8-11 09:52
哦,已经解决了,是ttyFIQ的问题。
能解释下ttyFIQ是什么东西吗?为什么要开启?怎么用ttyFIQ?

FIQ即:Fast Interrupt Request,如果板子打开了FIQ,那调试串口的节点就是/ttyFIQ0,打开了FIQ之后板子接串口可以进入FIQ,我的电脑是ubuntu下用ckermit,进入FIQ:Ctrl+]+B
回复

使用道具 举报

164

积分

0

威望

0

贡献

技术小白

积分
164
发表于 2016-9-8 16:48:08     
linjc 发表于 2016-8-16 09:25
FIQ即:Fast Interrupt Request,如果板子打开了FIQ,那调试串口的节点就是/ttyFIQ0,打开了FIQ之后板子接 ...

制作的根文件系统在跑不起来,log如下:
miniroot# boot /mnt:/ubuntu
/bin/sh: pkill: not found
umount: can't umount /mnt: Device or resource busy
SELinux:  Could not open policy file <= /etc/selinux/targeted/policy/policy.29:  No such file or directory
[ 1098.572648] init: plymouth-upstart-bridge main process (313) terminated with status 1
[ 1098.577994] init: plymouth-upstart-bridge main process ended, respawning
[ 1098.621660] init: plymouth-upstart-bridge main process (323) terminated with status 1
[ 1098.621823] init: plymouth-upstart-bridge main process ended, respawning
[ 1098.627153] init: ureadahead main process (316) terminated with status 5
[ 1098.654425] init: plymouth-upstart-bridge main process (328) terminated with status 1
[ 1098.654590] init: plymouth-upstart-bridge main process ended, respawning
[ 1098.839776] init: mounted-proc main process (341) terminated with status 1
* Starting Mount filesystems on boot[ OK ]
* Starting Signal sysvinit that the rootfs is mounted[ OK ]
* Starting Clean /tmp directory[ OK ]
* Starting Populate and link to /run filesystem[ OK ]
* Stopping Clean /tmp directory[ OK ]
* Stopping Populate and link to /run filesystem[ OK ]
* Stopping Track if upstart is running in a container[ OK ]
* Starting Initialize or finalize resolvconf[ OK ]
* Starting set console keymap[ OK ]
* Starting Signal sysvinit that virtual filesystems are mounted[ OK ]
* Starting Signal sysvinit that virtual filesystems are mounted[ OK ]
* Stopping set console keymap[ OK ]
* Starting Bridge udev events into upstart[ OK ]
* Starting Signal sysvinit that local filesystems are mounted[ OK ]
* Starting device node and kernel event manager[ OK ]
* Starting Signal sysvinit that remote filesystems are mounted[ OK ]
* Starting load modules from /etc/modules[ OK ]
* Starting cold plug devices[ OK ]
* Starting log initial device creation[ OK ]
* Stopping Mount filesystems on boot[ OK ]
* Stopping load modules from /etc/modules[ OK ]
* Starting flush early job output to logs[ OK ]
* Stopping flush early job output to logs[ OK ]
* Starting system logging daemon[ OK ]
* Starting configure network device security[ OK ]
* Stopping cold plug devices[ OK ]
* Stopping log initial device creation[ OK ]
* Starting configure network device[ OK ]
* Starting configure network device security[ OK ]
* Starting set console font[ OK ]
* Stopping set console font[ OK ]
* Starting userspace bootsplash[ OK ]
* Starting Send an event to indicate plymouth is up[ OK ]
* Stopping Send an event to indicate plymouth is up[ OK ]
* Stopping userspace bootsplash[ OK ]
* Starting System V initialisation compatibility[ OK ]
* Starting configure virtual network devices[ OK ]
* Stopping System V initialisation compatibility[ OK ]
* Starting System V runlevel compatibility[ OK ]
* Starting save kernel messages[ OK ]
* Starting regular background program processing daemon[ OK ]
* Stopping System V runlevel compatibility[ OK ]
* Stopping save kernel messages[ OK ]

帮忙分析一下是什么原因?
这块是3128的板子,之前3288制作的根文件系统没问题。
回复

使用道具 举报

600

积分

21

威望

25

贡献

技术大神

Rank: 3Rank: 3

积分
600

活跃会员

发表于 2016-9-8 17:34:07     
mlt911213 发表于 2016-9-8 16:48
制作的根文件系统在跑不起来,log如下:
miniroot# boot /mnt:/ubuntu
/bin/sh: pkill: not found

看log文件系统跑起来了,只是哪里出错了导致没有完全起来吧,这时候能显示吗?串口能输入吗?
回复

使用道具 举报

164

积分

0

威望

0

贡献

技术小白

积分
164
发表于 2016-9-9 15:10:03     
linjc 发表于 2016-9-8 17:34
看log文件系统跑起来了,只是哪里出错了导致没有完全起来吧,这时候能显示吗?串口能输入吗?

原来是串口配置的问题,现在解决了
回复

使用道具 举报

10

积分

0

威望

0

贡献

游客

积分
10
发表于 2016-10-11 16:27:02     
ubuntu文件系统启动停在这儿是怎么回事? A start job is running for dev-ttyFIQ0.device (31s / 1min 30s)
回复

使用道具 举报

返回列表
12
*滑块验证:
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

友情链接 : 爱板网 电子发烧友论坛 云汉电子社区 粤ICP备14022046号-2
快速回复 返回顶部 返回列表