RK3399启动到这里不动了，是什么原因，哪位大神帮忙看看
DDR Version 1.12 20180518In
Channel 0: LPDDR3, 800MHz
CS = 0
MR0=0x58
MR1=0x58
MR2=0x58
MR3=0x58
MR4=0x2
MR5=0x1
MR6=0x5
MR7=0x0
MR8=0x1F
MR9=0x1F
MR10=0x1F
MR11=0x1F
MR12=0x1F
MR13=0x1F
MR14=0x1F
MR15=0x1F
MR16=0x1F
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=32 Size=1024MB
Channel 1: LPDDR3, 800MHz
CS = 0
MR0=0x58
MR1=0x58
MR2=0x58
MR3=0x58
MR4=0x2
MR5=0x1
MR6=0x5
MR7=0x0
MR8=0x1F
MR9=0x1F
MR10=0x1F
MR11=0x1F
MR12=0x1F
MR13=0x1F
MR14=0x1F
MR15=0x1F
MR16=0x1F
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=32 Size=1024MB
256B stride
ch 0 ddrconfig = 0x101, ddrsize = 0x20
ch 1 ddrconfig = 0x101, ddrsize = 0x20
pmugrf_os_reg = 0x3280D280, stride = 0x9
OUT
Boot1: 2018-04-08, version: 1.12
CPUId = 0x0
ChipType = 0x10, 217
SdmmcInit=2 0
BootCapSize=100000
UserCapSize=7456MB
FwPartOffset=2000 , 100000
mmc0:cmd8,32
mmc0:cmd5,32
mmc0:cmd55,32
mmc0:cmd1,32
mmc0:cmd8,32
mmc0:cmd5,32
mmc0:cmd55,32
mmc0:cmd1,32
mmc0:cmd8,32
mmc0:cmd5,32
mmc0:cmd55,32
mmc0:cmd1,32
SdmmcInit=0 1
StorageInit ok = 67805
LoadTrustBL
No find bl30.bin
Load uboot, ReadLba = 2000
Load OK, addr=0x200000, size=0xa7790
RunBL31 0x10000
NOTICE:BL31: v1.3(debug):d98d16e
NOTICE:BL31: Built : 15:03:07, May 10 2018
NOTICE:BL31: Rockchip release version: v1.1
INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
INFO: Using opteed sec cpu_context!
INFO: boot cpu mask: 0
INFO: plat_rockchip_pmu_init(1151): pd status 3e
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
INF TEE-CORE:init_primary_helper:337: Initializing (1.1.0-170-gc4654a6 #16 Wed May 30 08:54:30 UTC 2018 aarch64)
INF TEE-CORE:init_primary_helper:338: Release version: 1.2
INF TEE-CORE:init_teecore:83: teecore inits done
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9
U-Boot 2017.09-01617-g9c62995 (Jul 03 2018 - 08:51:18 +0800)
Model: Firefly-RK3399 Board
DRAM:2 GiB
Relocation Offset is: 7fd18000
rk8xx_read: read reg 0x17 failed, ret=-121
MMC: dwmmc@fe320000: 1, sdhci@fe330000: 0
*** Warning - bad CRC, using default environment
In: serial@ff1a0000
Out: serial@ff1a0000
Err: serial@ff1a0000
Model: Firefly-RK3399 Board
Card did not respond to voltage select!
mmc_init: -95, time 9
switch to partitions #0, OK
mmc0(part 0) is current device
enter Recovery mode!
Net: eth0: ethernet@fe300000
Hit any key to stop autoboot:0
ANDROID: reboot reason: "recovery"
FDT load addr 0x10f00000 size 260 KiB
Booting kernel at 0x207f800 with fdt at 36c5800...
## Booting Android Image at 0x0207f800 ...
Kernel load addr 0x02080000 size 18845 KiB
RAM disk load addr 0x11000000 size 3958 KiB
## Flattened Device Tree blob at 036c5800
Booting using the fdt blob at 0x36c5800
XIP Kernel Image ... OK
Loading Ramdisk to 07e22000, end 081ff565 ... OK
Loading Device Tree to 0000000007e0c000, end 0000000007e210f6 ... OK
Adding bank: start=0x00200000, size=0x08200000
Adding bank: start=0x0a200000, size=0x75e00000
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.132 (wxt@SYS3) (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05) ) #4 SMP Mon Jul 2 19:58:20 CST 2018
[ 0.000000] Boot CPU: AArch64 Processor
[ 0.000000] earlycon: Early serial console at MMIO32 0xff1a0000 (options '')
[ 0.000000] bootconsole enabled
[ 0.000000] Reserved memory: failed to reserve memory for node 'drm-logo@00000000': base 0x0000000000000000, size 0 MiB
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc07fefa000 s45800 r8192 d32024 u86016
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.Total pages: 507912
[ 0.000000] Kernel command line: storagemedia=emmc androidboot.mode=emmc androidboot.slot_suffix= androidboot.serialno=29d4e64533db6ee9rw rootwait earlycon=uart8250,mmio32,0xff1a0000 swiotlb=1 console=ttyFIQ0 root=PARTUUID=614e0000-0000 rootfstype=ext4
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] software IO TLB (0MB) mapped at
[ 0.000000] Memory: 2003500K/2064384K available (11582K kernel code, 1692K rwdata, 4400K rodata, 1088K init, 756K bss, 60884K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000 ( 246 GB)
[ 0.000000] .init : 0xffffff8009030000 - 0xffffff8009140000 (1088 KB)
[ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008bd0000 ( 11584 KB)
[ 0.000000] .rodata : 0xffffff8008bd0000 - 0xffffff8009030000 (4480 KB)
[ 0.000000] .data : 0xffffff8009140000 - 0xffffff80092e7008 (1693 KB)
[ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum)
[ 0.000000] 0xffffffbdc0008000 - 0xffffffbdc2000000 ( 31 MB actual)
[ 0.000000] fixed : 0xffffffbffe7fb000 - 0xffffffbffec00000 (4116 KB)
[ 0.000000] PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000 ( 16 MB)
[ 0.000000] memory: 0xffffffc000200000 - 0xffffffc080000000 (2046 MB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000]Build-time adjustment of leaf fanout to 64.
[ 0.000000]RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] ITS: /interrupt-controller@fee00000/interrupt-controller@fee20000
[ 0.000000] ITS: allocated 65536 Devices @a300000 (psz 64K, shr 0)
[ 0.000000] ITS: using cache flushing for cmd queue
[ 0.000000] GIC: using LPI property table @0x000000000a290000
[ 0.000000] ITS: Allocated 1792 chunks for LPIs
[ 0.000000] CPU0: found redistributor 0 region 0:0x00000000fef00000
[ 0.000000] CPU0: using LPI pending table @0x000000000a2a0000
[ 0.000000] GIC: using cache flushing for LPI property table
[ 0.000000] GIC: PPI partition interrupt-partition-0 { /cpus/cpu@0 /cpus/cpu@1 /cpus/cpu@2 /cpus/cpu@3 }
[ 0.000000] GIC: PPI partition interrupt-partition-1 { /cpus/cpu@100 /cpus/cpu@101 }
[ 0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop0_frac as parent of dclk_vop0, rate changes may not work
[ 0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop1_frac as parent of dclk_vop1, rate changes may not work
[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.002001] Console: colour dummy device 80x25
[ 0.002434] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=24000)
[ 0.003398] pid_max: default: 32768 minimum: 301
[ 0.003971] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.004606] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.005980] Initializing cgroup subsys devices
[ 0.006407] Initializing cgroup subsys freezer
[ 0.006852] ftrace: allocating 41878 entries in 164 pages
[ 0.110911] sched-energy: Sched-energy-costs installed from DT
[ 0.111464] CPU0: update cpu_capacity 401
[ 0.111903] ASID allocator initialised with 32768 entries
[ 0.115552] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[ 0.116826] Platform MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[ 0.118961] Detected VIPT I-cache on CPU1
[ 0.118995] CPU1: found redistributor 1 region 0:0x00000000fef20000
[ 0.119025] CPU1: using LPI pending table @0x0000000000320000
[ 0.119070] CPU1: update cpu_capacity 401
[ 0.119074] CPU1: Booted secondary processor
[ 0.119599] Detected VIPT I-cache on CPU2
[ 0.119620] CPU2: found redistributor 2 region 0:0x00000000fef40000
[ 0.119648] CPU2: using LPI pending table @0x0000000000340000
[ 0.119676] CPU2: update cpu_capacity 401
[ 0.119679] CPU2: Booted secondary processor
[ 0.120202] Detected VIPT I-cache on CPU3
[ 0.120223] CPU3: found redistributor 3 region 0:0x00000000fef60000
[ 0.120250] CPU3: using LPI pending table @0x0000000000390000
[ 0.120278] CPU3: update cpu_capacity 401
[ 0.120282] CPU3: Booted secondary processor
[ 0.120800] Detected PIPT I-cache on CPU4
[ 0.120826] CPU4: found redistributor 100 region 0:0x00000000fef80000
[ 0.120866] CPU4: using LPI pending table @0x00000000003d0000
[ 0.120904] CPU4: update cpu_capacity 1024
[ 0.120908] CPU4: Booted secondary processor
[ 0.121439] Detected PIPT I-cache on CPU5
[ 0.121459] CPU5: found redistributor 101 region 0:0x00000000fefa0000
[ 0.121498] CPU5: using LPI pending table @0x000000007d000000
[ 0.121525] CPU5: update cpu_capacity 1024
[ 0.121528] CPU5: Booted secondary processor
[ 0.121615] Brought up 6 CPUs
[ 0.133677] SMP: Total of 6 processors activated.
[ 0.134118] CPU features: detected feature: GIC system register CPU interface
[ 0.134793] CPU: All CPU(s) started at EL2
[ 0.135214] alternatives: patching kernel code
[ 0.137029] devtmpfs: initialized
[ 0.151268] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.152244] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 0.153313] pinctrl core: initialized pinctrl subsystem
[ 0.154572] NET: Registered protocol family 16
[ 0.160297] cpuidle: using governor ladder
[ 0.164305] cpuidle: using governor menu
[ 0.164704] Registered FIQ tty driver
[ 0.165365] vdso: 2 pages (1 code @ ffffff8008bd6000, 1 data @ ffffff8009144000)
[ 0.166109] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.166932] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.190229] console enabled
[ 0.190229] console enabled
[ 0.190910] bootconsole disabled
[ 0.190910] bootconsole disabled
[ 0.191829] Registered fiq debugger ttyFIQ0
[ 0.221086] iommu: Adding device ff650000.vpu_service to group 0
[ 0.221690] iommu: Adding device ff660000.rkvdec to group 1
[ 0.222277] iommu: Adding device ff8f0000.vop to group 2
[ 0.222822] iommu: Adding device ff900000.vop to group 3
[ 0.224608] SCSI subsystem initialized
[ 0.225113] usbcore: registered new interface driver usbfs
[ 0.225649] usbcore: registered new interface driver hub
[ 0.226195] usbcore: registered new device driver usb
[ 0.226726] media: Linux media interface: v0.10
[ 0.227164] Linux video capture interface: v2.00
[ 0.227608] pps_core: LinuxPPS API ver. 1 registered
[ 0.228057] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.228867] PTP clock support registered
[ 0.230236] Advanced Linux Sound Architecture Driver Initialized.
[ 0.231244] Bluetooth: Core ver 2.21
[ 0.231587] NET: Registered protocol family 31
[ 0.231981] Bluetooth: HCI device and connection manager initialized
[ 0.232553] Bluetooth: HCI socket layer initialized
[ 0.232986] Bluetooth: L2CAP socket layer initialized
[ 0.233467] Bluetooth: SCO socket layer initialized
[ 0.234996] clocksource: Switched to clocksource arch_sys_counter
[ 0.283267] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[ 0.284179] NET: Registered protocol family 2
[ 0.285019] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.285749] TCP bind hash table entries: 16384 (order: 7, 524288 bytes)
[ 0.286781] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.287452] UDP hash table entries: 1024 (order: 4, 98304 bytes)
[ 0.288080] UDP-Lite hash table entries: 1024 (order: 4, 98304 bytes)
[ 0.288923] NET: Registered protocol family 1
[ 0.289619] RPC: Registered named UNIX socket transport module.
[ 0.290160] RPC: Registered udp transport module.
[ 0.290577] RPC: Registered tcp transport module.
[ 0.291002] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.292195] Trying to unpack rootfs image as initramfs...
[ 0.493420] Freeing initrd memory: 3956K
[ 0.494271] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[ 0.495083] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
[ 0.499108] Initialise system trusted keyring
[ 0.507406] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.508702] NFS: Registering the id_resolver key type
[ 0.509188] Key type id_resolver registered
[ 0.509559] Key type id_legacy registered
[ 0.509996] fuse init (API version 7.23)
[ 0.510716] SGI XFS with security attributes, no debug enabled
[ 0.515897] NET: Registered protocol family 38
[ 0.516319] Key type asymmetric registered
[ 0.516694] Asymmetric key parser 'x509' registered
[ 0.517296] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 0.517957] io scheduler noop registered
[ 0.518327] io scheduler deadline registered
[ 0.518835] io scheduler cfq registered (default)
[ 0.520643] phy phy-ff770000.syscon:usb2-phy@e460.0: Failed to get VBUS supply regulator
[ 0.526150] rockchip-pcie f8000000.pcie: no vpcie3v3 regulator found
[ 0.526731] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found
[ 0.527329] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found
[ 1.069042] rockchip-pcie f8000000.pcie: PCIe link training gen1 timeout!
[ 1.069762] rockchip-pcie: probe of f8000000.pcie failed with error -110
[ 1.071491] rk-vcodec ff650000.vpu_service: no regulator for vcodec
[ 1.072398] rk-vcodec ff650000.vpu_service: probe device
[ 1.072916] rk-vcodec ff650000.vpu_service: vpu mmu dec ffffffc07d22a410
[ 1.073769] rk-vcodec ff650000.vpu_service: allocator is drm
[ 1.074350] rk-vcodec ff650000.vpu_service: checking hw id 0
[ 1.075523] rk-vcodec ff650000.vpu_service: could not find power_model node
[ 1.076161] rk-vcodec ff650000.vpu_service: init success
[ 1.077047] rk-vcodec ff660000.rkvdec: no regulator for vcodec
[ 1.078060] rk-vcodec ff660000.rkvdec: probe device
[ 1.078530] rk-vcodec ff660000.rkvdec: vpu mmu dec ffffffc07d22ac10
[ 1.079276] rk-vcodec ff660000.rkvdec: allocator is drm
[ 1.079794] rk-vcodec ff660000.rkvdec: checking hw id 6876
[ 1.080635] rk-vcodec ff660000.rkvdec: could not find power_model node
[ 1.081236] rk-vcodec ff660000.rkvdec: init success
[ 1.083137] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 1.083808] dma-pl330 ff6d0000.dma-controller: DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
[ 1.086071] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 1.086741] dma-pl330 ff6e0000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
LZ 是哪块板，做了什么操作造成启动不了？
页:
[1]