安装附加的软件，进行 SD 卡格式化
请问使用什么软件，没有看到有附件，我使用傲梅分区助手进行全写0完成低级格式化 链接: https://pan.baidu.com/s/1bygrvd__Gm64EVwKga92Tw?pwd=1234 提取码: 1234
--来自百度网盘超级会员v9的分享 Oliver_Li 发表于 2025-3-27 13:46
链接: https://pan.baidu.com/s/1bygrvd__Gm64EVwKga92Tw?pwd=1234 提取码: 1234
--来自百度网盘超级会员 ...
与傲梅分区助手格式化后结果相同。
再次提醒，我格式化的卡使用自己编的包能正常烧录，贵司百度云提供的包无法烧录
请确认贵司提供的包是否正常或确认是否需要执行切换dts type等指令
给我看看，插卡上电的时候，系统打印的第一段日志 Oliver_Li 发表于 2025-3-27 14:44
给我看看，插卡上电的时候，系统打印的第一段日志
请看错误日志
sophon#
sophon# B.R.SCS/0/0.WD.URPL.SDI/25000000/6000000.BS/SD.PS.SD/0x0/0x1000/0x1000/0.PE.BS.SD/0x1000/0x16800/0x16800/0.BE.J.
FSBL Jb2869:g8d5c732-dirty:2024-07-17T09:52:18+08:00
SRAM Log: ========================================
I:PCIE: mode 0
I:next_xlat 1, MAX_XLAT_TABLES 6
I:next_xlat 2, MAX_XLAT_TABLES 6
I:next_xlat 3, MAX_XLAT_TABLES 6
I:next_xlat 4, MAX_XLAT_TABLES 6
I:V/4ccb2a2f/vueTPvX:g1b2c9ab2/0/29400000.
SCS/0/0. I:ep_swinfo.
I:sw_info=0x0
I:EP:0x33050224/0x0.
I:EP:0x3305022c/0x0.
I:EP:0x33050234/0x294106bd.
I:EP:0x3305023c/0x294106b9.
I:EP:0x33050244/0x294106b5.
I:EP:0x3305024c/0x294106b1.
I:EP:0x33050254/0x294106ad.
I:EP:0x3305025c/0x294106a9.
I:EP:0x33050264/0x294106a5.
I:EP:0x3305026c/0x29406205.
I:EP:0x33050274/0x2940a8c9.
I:ep_dev.
I:EP:0x33050224/0x0.
I:EP:0x3305022c/0x0.
I:EP:0x33050234/0x294106bd.
I:EP:0x3305023c/0x294106b9.
I:EP:0x33050244/0x294106b5.
I:EP:0x3305024c/0x294106b1.
I:EP:0x33050254/0x294106ad.
I:EP:0x3305025c/0x294106a9.
I:EP:0x33050264/0x294106a5.
I:EP:0x3305026c/0x29406205.
I:EP:0x33050274/0x2940a8c9.
WD.URPL. I:bm_sd_phy_init
I:ep_dev.
I:EP:0x33050224/0x0.
I:EP:0x3305022c/0x0.
I:EP:0x33050234/0x294106bd.
I:EP:0x3305023c/0x294106b9.
I:EP:0x33050244/0x294106b5.
I:EP:0x3305024c/0x294106b1.
I:EP:0x33050254/0x294106ad.
I:EP:0x3305025c/0x294106a9.
I:EP:0x33050264/0x294106a5.
I:EP:0x3305026c/0x29406205.
I:EP:0x33050274/0x2940a8c9.
SDI/25000000/6000000. I:Set SDCLK by driver. (Source, Target, div, Actual) = (25000000, 200000, 63, 198412)
I:SD init done
I:cid manufacturer_id:0x3 card_bga:0x3 name:?G23KSDS
I:sd_rca:43690
I:csd spec_vers:0x0 erase_grp_size:0x1f
I:Set SDCLK by driver. (Source, Target, div, Actual) = (25000000, 6000000, 3, 4166666)
I:sd_open_fip
I:BS/cea0.
BS/SD.PS. I:LIS/0xcea0/0x25039000/0x0/4096/0.
SD/0x0/0x1000/0x1000/0. I:LIE/0/0x25039000/0x0/4096.
PE. I:CS/0x5200200/0x0/0x20f00008.
I:No BLCP.
BS. I:LIS/0xcea0/0x25000000/0x1000/92160/0.
SD/0x1000/0x16800/0x16800/0. I:LIE/0/0x25000000/0x1000/92160.
BE. I:bl2_entry=0x25000020
J.
SRAM Log end: ====================================
st_on_reason=2d0000
st_off_reason=0
P2S/0x1000/0x25018800.
SD/0x17800/0x1000/0x1000/0.P2E.
D-2024-04-28
Auto: board info: single rank, dual sys, lpddr4, 4266.
GPIO117 status =========== 0x0
============adc3 val: 819, vol: 299 mV=================
DDR subsys0 init.
Dram Datarate: 4266Mbps.
SSC_OFF.
ZQ CAL.
DDR BIST PASS
DDR subsys1 init.
Dram Datarate: 4266Mbps.
SSC_OFF.
ZQ CAL.
DDR BIST PASS
Total Dram Size: 4096MBytes
PLLS.
PLLE.
EMI/375000000/12000000.Load OEM info end.
C2S/0x0/0x0/0x0.
No C906L image.
MS/0x1a800/0x100000000/0x8200.
SD/0x1a800/0x8200/0x8200/0.ME.
BL32/0x22a00/0x100050000/0x5200.
SD/0x22a00/0x5200/0x5200/0.ME.
BL32/0x27c00/0x5200000/0x5000.
SD/0x27c00/0x5000/0x5000/0.ME.
L2/0x2cc00.
SD/0x2cc00/0x200/0x200/0.L2/0x414d3342/0xcafe4bcc/0x1000a0000/0x44e00/0x44e00
COMP/1.
SD/0x2cc00/0x44e00/0x44e00/0.DCP/0x1000a0020/0x1000000/0x101100020/0x44e00/1.
DCP/0x1da018/0.
Loader_2nd loaded.
U/100000000/N/1000a0020/
B100050000-3c000.start BL32
image_type :1
U-Boot 2021.10-g35fa8dccda (Oct 09 2024 - 17:18:50 +0800) cvitek_sophgo
DRAM:4 GiB
Relocation Offset is: fb687000
Relocating to 1fb727000, new gd at 1fa9ffd90, sp at 1fa9f60e0
WDT: Started with servicing (30s timeout)
MMC: cvi_sdhci_probe-470: mmc0 probe
cvi_sdhci_probe-470: mmc0 probe
cvi_sdhci_probe-470: mmc0 probe
cv-emmc@29300000: 0, cv-sd@29310000: 1, wifi-sd@29330000: 2
Loading Environment from MMC... *** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
switch to partitions #2, OK
mmc0(part 2) is current device
MMC read: dev # 0, block # 0, count 96 ... 96 blocks read: OK in 2 ms (23.4 MiB/s)
switch to partitions #2, OK
mmc0(part 2) is current device
MMC read: dev # 0, block # 0, count 96 ... 96 blocks read: OK in 2 ms (23.4 MiB/s)
FORCE INFO: DTS_TYPE
hdmi disconnected
Net:
Warning: ethernet@290e0000 (eth0) using random MAC address - 72:4f:26:37:a3:73
eth0: ethernet@290e0000
Warning: ethernet@290f0000 (eth1) using random MAC address - 0a:dd:b3:96:48:9b
, eth1: ethernet@290f0000
Hit any key to stop autoboot:0
## Resetting to default environment
fs reading: //boot.scr
** Unable to read file //boot.scr **
Failed to load '//boot.scr'
## Executing script at 120000000
Wrong image format for "source" command
load from no partition sd
** fs_devread read error - block
Failed to mount ext2 filesystem...
Can't set block device
## Executing script at 120000000
Wrong image format for "source" command
fs reading: boot.scr.emmc
548 bytes read in 3 ms (177.7 KiB/s)
## Executing script at 120000000
Athena2 boot script
fs reading: boot.itb
18878170 bytes read in 834 ms (21.6 MiB/s)
## Loading kernel from FIT Image at 104000000 ...
Could not find configuration node
ERROR: can't get kernel image!
sophon#
页:
1
[2]