自己编译android烧写后系统反复重启
大家好，我是11月初就买了firefly-RK3288的板,从你们站上下载了android源代码编译后下载进去，系统反复重启。开始以为是没有更新最新代码（因为我git pull bitbucket master:master重来没有完成过，速度很慢都是中途就断开了），
昨天又下载了最新的代码 （git clone -b firefly/master git://git.us.linux-rockchip.org/rk3288_r-box_android4.4.2_sdk.git）
但是今天把最新代码编译出来的img烧进去，还是系统反复重新启动，请高手指点，启动串口信息如下：
In
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Memory OK
Memory OK
OUT
U-Boot 2014.10-RK3288-02 (Oct 30 2014 - 09:27:41)
CPU: rk3288
CPU's clock information:
arm pll = 600000000HZ
periph pll = 300000000HZ
ddr pll = 200000000HZ
codec pll = 594000000HZ
Board: Rockchip platform Board
DRAM:Found dram banks:1
Adding bank:0000000000000000(0000000080000000)
128 MiB
storage init OK!
Using default environment
GetParam
check parameter success
Unknow param: MACHINE_MODEL:rk30sdk!
Unknow param: MACHINE_ID:007!
Unknow param: MANUFACTURER:RK30SDK!
Unknow param: PWR_HLD: 0,0,A,0,1!
failed to prepare fdt from boot!
power key: bank-0 pin-5
can't find dts node for ricoh619
pmic:act8846
Can't find dts node for fuel guage cw201x
SecureBootEn = 0, SecureBootLock = 0
#Boot ver: 2014-10-30#2.17
sn:1006110001000029
no fuel gauge found
no fuel gauge found
read logo_on switch from dts
checkKey
vbus = 0
no fuel gauge found
Hit any key to stop autoboot:0
failed to load fdt from boot!
kernel @ 0x02000000 (0x005f3cf0)
ramdisk@ 0x059fc000 (0x00120f04)
Secure Boot state: 0
bootrk: do_bootm_linux...
Loading Device Tree to 0561c000, end 05636f1c ... OK
Add bank:0000000000000000, 0000000080000000
Starting kernel ...
<hit enter to activate fiq debugger>
[ 0.000000] Booting Linux on physical CPU 0x500
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.10.0 (leo@ubuntu) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #1 SMP PREEMPT Thu Nov 20 17:24:20 CST 2014
[ 0.000000] CPU: ARMv7 Processor revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Rockchip RK3288 (Flattened Device Tree), model: rockchip,rk3288
[ 0.000000] rockchip_ion_reserve
[ 0.000000] cma: CMA: reserved 16 MiB at 2e800000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] PERCPU: Embedded 9 pages/cpu @c1eac000 s14016 r8192 d14656 u36864
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.Total pages: 522768
[ 0.000000] Kernel command line: console=ttyFIQ0 androidboot.hardware=rk30board androidboot.console=ttyFIQ0 board.ap_has_alsa=0 init=/initmtdparts=rk29xxnand:0x00002000@0x00002000(uboot),0x00002000@0x00004000(misc),0x00008000@0x00006000(resource),0x00008000@0x0000e000(kernel),0x00010000@0x00016000(boot),0x00010000@0x00026000(recovery),0x0001a000@0x00036000(backup),0x00040000@0x00050000(cache),0x00002000@0x00090000(kpanic),0x00180000@0x00092000(system),0x00002000@0x00212000(metadata),0x00200000@0x00214000(userdata),0x00020000@0x00414000(radical_update),-@0x00434000(user) storagemedia=emmc loader.timestamp=2014-10-30_09:27:41 androidboot.serialno=1006110001000029
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 2048MB = 2048MB total
[ 0.000000] Memory: 2047124k/2047124k available, 50028k reserved, 1318912K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector: 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap: 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem: 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 (14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0a6ea3c (10651 kB)
[ 0.000000] .init : 0xc0a6f000 - 0xc0cbd6c0 (2362 kB)
[ 0.000000] .data : 0xc0cbe000 - 0xc0d5ab48 ( 627 kB)
[ 0.000000] .bss : 0xc0d5ab48 - 0xc0e74d84 (1129 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000]RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] rk_clk_tree_init start! cru base = 0xfed00000
[ 0.000000] rk_get_uboot_display_flag: uboot_logo_on = 0
[ 0.000000] rkclk_init_clks: cnt_parent = 7
[ 0.000000] rkclk_init_clks: cnt_rate = 32
[ 0.000000] Architected local timer running at 24.00MHz (phys).
[ 0.000000] Switching to timer-based delay loop
[ 0.000000] sched_clock: ARM arch timer >56 bits at 24000kHz, resolution 41ns
[ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
[ 0.446564] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.446580] pid_max: default: 32768 minimum: 301
[ 0.446686] Security Framework initialized
[ 0.446701] SELinux:Initializing.
[ 0.446777] Mount-cache hash table entries: 512
[ 0.447408] Initializing cgroup subsys debug
[ 0.447423] Initializing cgroup subsys freezer
[ 0.447450] CPU: Testing write buffer coherency: ok
[ 0.447763] /cpus/cpu@0 missing clock-frequency property
[ 0.447775] /cpus/cpu@1 missing clock-frequency property
[ 0.447784] /cpus/cpu@2 missing clock-frequency property
[ 0.447794] /cpus/cpu@3 missing clock-frequency property
[ 0.447840] CPU0: thread -1, cpu 0, socket 5, mpidr 80000500
[ 0.447891] Setting up static identity map for 0xc0785160 - 0xc07851b8
[ 0.450158] last_log: 0x2e100000 map to 0xf0004000 and copy to 0xf0086000, size 0x80000 early 0x1368 (version 3.0)
[ 0.525257] CPU1: Booted secondary processor
[ 0.525290] CPU1: thread -1, cpu 1, socket 5, mpidr 80000501
[ 0.544950] CPU2: Booted secondary processor
[ 0.544974] CPU2: thread -1, cpu 2, socket 5, mpidr 80000502
[ 0.564652] CPU3: Booted secondary processor
[ 0.564675] CPU3: thread -1, cpu 3, socket 5, mpidr 80000503
[ 0.564777] Brought up 4 CPUs
[ 0.564805] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[ 0.564815] CPU: All CPU(s) started in SVC mode.
[ 0.565549] devtmpfs: initialized
[ 0.570712] pinctrl core: initialized pinctrl subsystem
[ 0.570954] regulator-dummy: no parameters
[ 0.571457] NET: Registered protocol family 16
[ 0.573016] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.573273] ion_snapshot: 0x2e1b0000 map to 0xf0107000 and copy to 0xc0e503d4 (version 0.1)
[ 0.573575] Registered FIQ tty driver
[ 0.574718] console enabled
[ 0.574929] Registered fiq debugger ttyFIQ0
[ 0.575437] rockchip_get_bank_data:name=base start=0xff750000,end=0xff7500ff
[ 0.575461] rockchip_get_bank_data:name=mux_bank0 start=0xff730084,end=0xff73008f
[ 0.575481] rockchip_get_bank_data:name=pull_bank0 start=0xff730064,end=0xff73006f
[ 0.575508] rockchip_get_bank_data:name=drv_bank0 start=0xff730070,end=0xff73007b
[ 0.575605] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio1@ff780000 start=0xff780000,end=0xff7800ff
[ 0.575670] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio2@ff790000 start=0xff790000,end=0xff7900ff
[ 0.575733] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio3@ff7a0000 start=0xff7a0000,end=0xff7a00ff
[ 0.575797] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio4@ff7b0000 start=0xff7b0000,end=0xff7b00ff
[ 0.575858] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio5@ff7c0000 start=0xff7c0000,end=0xff7c00ff
[ 0.575920] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio6@ff7d0000 start=0xff7d0000,end=0xff7d00ff
[ 0.575982] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio7@ff7e0000 start=0xff7e0000,end=0xff7e00ff
[ 0.576045] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio8@ff7f0000 start=0xff7f0000,end=0xff7f00ff
[ 0.576114] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio15@ff7f2000 start=0xff7f2000,end=0xff7f20ff
[ 0.576179] rockchip_pinctrl_probe:name=RK3288-GPIO,type=3
[ 0.576195] rockchip_pinctrl_probe:name=base start=0xff770000,end=0xff77013f
[ 0.576209] rockchip_pinctrl_probe:name=pull start=0xff770140,end=0xff7701bf
[ 0.576224] rockchip_pinctrl_probe:name=drv start=0xff7701c0,end=0xff77023f
[ 0.576723] rockchip_interrupts_register:bank_num=7
[ 0.578617] of_get_gpio_init_config:gpio = 256, value = 0
[ 0.578640] of_get_gpio_init_config:gpio = 233, value = 0
[ 0.578663] of_get_gpio_init_config:gpio = 136, value = 0
[ 0.578736] rockchip_pinctrl_probe:init ok
[ 0.584368] rk_iommu ff900800.iep_mmu: (iep) Enter
[ 0.584487] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.584503] rk_iommu ff900800.iep_mmu: (iep) Initialized
[ 0.584668] rk_iommu ff950800.vip_mmu: (vip) Enter
[ 0.584774] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.584789] rk_iommu ff950800.vip_mmu: (vip) Initialized
[ 0.584947] rk_iommu ff930300.vopb_mmu: (vopb) Enter
[ 0.585052] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.585067] rk_iommu ff930300.vopb_mmu: (vopb) Initialized
[ 0.585224] rk_iommu ff940300.vopl_mmu: (vopl) Enter
[ 0.585336] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.585352] rk_iommu ff940300.vopl_mmu: (vopl) Initialized
[ 0.585513] rk_iommu ff9c0440.hevc_mmu: (hevc) Enter
[ 0.585639] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.585654] rk_iommu ff9c0440.hevc_mmu: (hevc) Initialized
[ 0.585808] rk_iommu ff9a0800.vpu_mmu: (vpu) Enter
[ 0.585914] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.585930] rk_iommu ff9a0800.vpu_mmu: (vpu) Initialized
[ 0.586097] rk_iommu ff914000.isp_mmu: (isp_mmu) Enter
[ 0.586220] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.586235] rk_iommu ff914000.isp_mmu: (isp_mmu) Initialized
[ 0.587833] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.587849] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.588053] DDR DEBUG: version 1.00 20140603
[ 0.588087] DDR DEBUG: Channel a:
[ 0.588098] DDR DEBUG: DDR3 Device
[ 0.588113] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Total Capability=1024MB
[ 0.588125] DDR DEBUG: Channel b:
[ 0.588134] DDR DEBUG: DDR3 Device
[ 0.588147] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Total Capability=1024MB
[ 0.588160] DDR DEBUG: addr=0xd60000
[ 0.588171] DDR DEBUG: stride=9, size=256, halfcap=40000000
[ 0.588183] DDR DEBUG: socAddr=0xd60000, socAddr=0xd60100
[ 0.588194] DDR DEBUG: chAddr=0xd60000, chAddr=0xd60000
[ 0.588207] DDR DEBUG: dtar=0x1ac000, dtar=0x1ac000
[ 0.588263] DDR DEBUG: init success!!! freq=200MHz
[ 0.588272] DDR DEBUG: Channel a:
[ 0.588286] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.588303] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.588319] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.588335] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.588350] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0
[ 0.588363] DDR DEBUG: DRV Pull-Up=0x19, DRV Pull-Dwn=0x19
[ 0.588375] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2
[ 0.588384] DDR DEBUG: Channel b:
[ 0.588397] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.588413] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.588429] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.588445] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.588460] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0
[ 0.588472] DDR DEBUG: DRV Pull-Up=0x19, DRV Pull-Dwn=0x19
[ 0.588483] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2
[ 0.609301] bio: create slab <bio-0> at 0
[ 0.609941] Enter firefly_noatx8_init
[ 0.610100] firefly_noatx8_probe 51
[ 0.610327] SCSI subsystem initialized
[ 0.610478] usbcore: registered new interface driver usbfs
[ 0.610522] usbcore: registered new interface driver hub
[ 0.610617] usbcore: registered new device driver usb
[ 0.611594] rockchip_i2c ff650000.i2c: i2c-0: Rockchip I2C adapter
[ 0.613024] rockchip_i2c ff140000.i2c: i2c-1: Rockchip I2C adapter
[ 0.613473] rockchip_i2c ff660000.i2c: i2c-2: Rockchip I2C adapter
[ 0.613944] rockchip_i2c ff150000.i2c: i2c-3: Rockchip I2C adapter
[ 0.614192] rockchip_i2c ff160000.i2c: i2c-4: Rockchip I2C adapter
[ 0.615066] media: Linux media interface: v0.10
[ 0.615110] Linux video capture interface: v2.00
[ 0.615158] pps_core: LinuxPPS API ver. 1 registered
[ 0.615171] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.615195] PTP clock support registered
[ 0.615427] rockchip_ion_parse_dt: num_heaps = 1
[ 0.615445] 0:03vmalloc0x(null)
[ 0.615712] Rockchip ion module is successfully loaded (v1.0)
[ 0.615878] Advanced Linux Sound Architecture Driver Initialized.
[ 0.616270] Bluetooth: Core ver 2.16
[ 0.616311] NET: Registered protocol family 31
[ 0.616322] Bluetooth: HCI device and connection manager initialized
[ 0.616342] Bluetooth: HCI socket layer initialized
[ 0.616357] Bluetooth: L2CAP socket layer initialized
[ 0.616386] Bluetooth: SCO socket layer initialized
[ 0.616615] cfg80211: Calling CRDA to update world regulatory domain
[ 0.617203] act8846_i2c_probe,line=898
[ 0.618182] act8846_parse_dt,line=746
[ 0.618619] act8846_i2c_probe: act8846_pmic_hold=1
[ 0.618643] act8846_i2c_probe: act8846_pmic_sleep=1
[ 0.618661] act8846_i2c_probe: act8846_pmic_cpu_det_gpio=1
[ 0.618678] act8846_i2c_probe: act8846_pmic_usb_hub_reset_gpio=1
[ 0.620494] act_dcdc1: 1200 mV
[ 0.623189] vccio: 3300 mV
[ 0.625046] vdd_logic: 700 <--> 1500 mV at 1100 mV
[ 0.627728] act_dcdc4: 2000 mV
[ 0.628970] vccio_sd: 1800 <--> 3300 mV at 3300 mV
[ 0.631023] act_ldo2: 1050 mV
[ 0.633083] act_ldo3: 1800 mV
[ 0.635142] act_ldo4: 3300 mV
[ 0.637190] act_ldo5: 3300 mV
[ 0.639245] act_ldo6: 1100 mV
[ 0.641313] vcc_18: 1800 mV
[ 0.643379] act_ldo8: 1850 mV
[ 0.648089] vdd_arm: 712 <--> 1500 mV at 1000 mV
[ 0.652737] vdd_gpu: 712 <--> 1500 mV at 1000 mV
[ 0.653174] rk808_i2c_probe,line=1368
[ 0.654497] The device is not rk808 -11
[ 0.654585] rk808: probe of 0-001b failed with error -11
[ 0.655946] Switching to clocksource arch_sys_counter
[ 0.677367] rk-fb rockchip-fb: rk fb ion client create success!
[ 0.677396] rk-fb rockchip-fb: rockchip framebuffer driver probe
[ 0.677881] rk-screen rk_screen.9: rockchip screen probe success
[ 0.678162] rk32-lvds rk32-lvds: rk32 lvds driver probe success
[ 0.678379] rk32-edp ff970000.edp: screen is not edp!
[ 0.678402] rk32-edp: probe of ff970000.edp failed with error -22
[ 0.678760] rk3288-lcdc lcdc0: can't find power_ctr node for lcdc0
[ 0.679077] graphics fb0: rockchip framebuffer registerd:fb0
[ 0.679473] graphics fb1: rockchip framebuffer registerd:fb1
[ 0.679654] graphics fb2: rockchip framebuffer registerd:fb2
[ 0.679808] graphics fb3: rockchip framebuffer registerd:fb3
[ 0.679960] graphics fb4: rockchip framebuffer registerd:fb4
[ 0.680621] rk_iommu ff930300.vopb_mmu: (vopb) Enabled
[ 0.680775] rk3288-lcdc lcdc0: lcdc0: dclk:148500000>>fps:60
[ 0.680802] rk3288-lcdc lcdc0: wakeup from standby!
[ 0.726434] alloc_buffer:ion_phy_addr=0x10000000
[ 0.739138] fb0:phy:10000000>>vir:f0191000>>len:0x1800000
[ 0.768886] rk3288-lcdc lcdc0: lcdc0 probe ok, iommu enabled
[ 0.769392] rockchip_set_mux:warning ignore bank num 15
[ 0.769533] rockchip_set_mux:warning ignore bank num 15
[ 0.769645] rockchip_set_mux:warning ignore bank num 15
[ 0.769765] rockchip_set_mux:warning ignore bank num 15
[ 0.769873] rockchip_set_mux:warning ignore bank num 15
[ 0.769986] rockchip_set_mux:warning ignore bank num 15
[ 0.770601] rockchip_set_mux:warning ignore bank num 15
[ 0.770775] rockchip_set_mux:warning ignore bank num 15
[ 0.771341] rockchip_set_mux:warning ignore bank num 15
[ 0.771487] rockchip_set_mux:warning ignore bank num 15
[ 0.772031] rockchip_set_mux:warning ignore bank num 15
[ 0.772173] rockchip_set_mux:warning ignore bank num 15
[ 0.772738] rockchip_set_mux:warning ignore bank num 15
[ 0.772893] rockchip_set_mux:warning ignore bank num 15
[ 0.774396] NET: Registered protocol family 2
[ 0.774893] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.775033] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.775170] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.775230] TCP: reno registered
[ 0.775248] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.775285] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.775496] NET: Registered protocol family 1
[ 0.775692] Unpacking initramfs...
[ 0.838504] Freeing initrd memory: 1152K (c59fc000 - c5b1c000)
[ 0.839125] hw perfevents: enabled with ARMv7 Cortex-A12 PMU driver, 7 counters available
[ 0.839624] probe device ff9a0000.vpu_service
[ 0.839849] vpu_service: power on
[ 0.840920] checking hw id 4831
[ 0.841373] vpu_service set to auto frequency mode
[ 0.841436] vcodec vpu_service: vcodec ion client create success!
[ 0.841899] rk_iommu ff9a0800.vpu_mmu: (vpu) Enabled
[ 0.841932] rk_iommu ff9a0800.vpu_mmu: (vpu) Disabled
[ 0.841947] rk_iommu ff9a0800.vpu_mmu: rockchip_iommu_detach_device: Detached IOMMU with pgtable 0x2e26e000
[ 0.841962] vpu_service: power off...
[ 0.842002] done
[ 0.842012] init success
[ 0.842076] probe device ff9c0000.hevc_service
[ 0.842266] hevc_service: power on
[ 0.843330] checking hw id 6867
[ 0.843617] vcodec hevc_service: vcodec ion client create success!
[ 0.843902] rk_iommu ff9c0440.hevc_mmu: (hevc) Enabled
[ 0.843932] rk_iommu ff9c0440.hevc_mmu: (hevc) Disabled
[ 0.843947] rk_iommu ff9c0440.hevc_mmu: rockchip_iommu_detach_device: Detached IOMMU with pgtable 0x2e26c000
[ 0.843960] hevc_service: power off...
[ 0.843998] done
[ 0.844007] init success
[ 0.844125] rknandbase v1.0 2014-03-31
[ 0.844340] rknand_probe clk rate = 148500000
[ 0.844451] rknand_driver:ret = 0
[ 0.844837] audit: initializing netlink socket (disabled)
[ 0.844884] type=2000 audit(0.400:1): initialized
[ 0.845705] bounce pool size: 64 pages
[ 0.850163] fuse init (API version 7.22)
[ 0.850558] msgmni has been set to 1456
[ 0.852544] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 0.852564] io scheduler noop registered
[ 0.852576] io scheduler deadline registered
[ 0.852669] io scheduler cfq registered (default)
[ 0.853530] rga ff920000.rga: rga ion client create success!
[ 0.853674] rga: Driver loaded succesfully
[ 0.854118] IEP Power ON
[ 0.854157] iep ion client create success!
[ 0.854525] rk_iommu ff900800.iep_mmu: (iep) Enabled
[ 0.854551] IEP Power OFF
[ 0.854565] rk_iommu ff900800.iep_mmu: (iep) Disabled
[ 0.854580] rk_iommu ff900800.iep_mmu: rockchip_iommu_detach_device: Detached IOMMU with pgtable 0x2e261000
[ 0.854598] IEP Driver loaded succesfully
[ 0.854702] Module initialized.
[ 0.855452] dma-pl330 ffb20000.pdma: Loaded driver for PL330 DMAC-2364208
[ 0.855472] dma-pl330 ffb20000.pdma:DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10
[ 0.856700] dma-pl330 ff250000.pdma: Loaded driver for PL330 DMAC-2364208
[ 0.856720] dma-pl330 ff250000.pdma:DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[ 0.856991] pwm-voltage-regulator pwm_regulator.23: unable to request PWM, trying legacy API
[ 0.857011] pwm-voltage-regulator pwm_regulator.23: unable to request legacy PWM
[ 0.857023] pwm_regulator_probe:error
[ 0.857047] platform pwm_regulator.23: Driver pwm-voltage-regulator requests probe deferral
[ 0.857390] rk_serial.c v1.8 2014-03-04
[ 0.857605] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 87) is a rk29_serial.0
[ 0.857798] serial ff180000.serial: membase 0xf015e000
[ 0.860564] loop: module loaded
[ 0.861170] SCSI Media Changer driver v0.25
[ 0.861462] tun: Universal TUN/TAP device driver, 1.6
[ 0.861476] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.862029] stmmac_probe_config_dt: Can not read property: pmu_regulator.
[ 0.862048] stmmac_probe_config_dt: Can not read property: pmu_enable_level.
[ 0.862062] stmmac_probe_config_dt: clock input or output? (input).
[ 0.862075] stmmac_probe_config_dt: TX delay(0x30).
[ 0.862086] stmmac_probe_config_dt: RX delay(0x10).
[ 0.862125] stmmac_probe_config_dt: is rockchip,rk3288-gmac
[ 0.862136] stmmc_pltfr_init:
[ 0.862146] stmmc_pltfr_init: ERROR: Get power-gpio failed.
[ 0.862169] stmmc_pltfr_init: ERROR: Request gmac phy reset pin failed.
[ 0.862180] stmmc_pltfr_init: init for RGMII
[ 0.862192] tx delay=0x30
[ 0.862192] rx delay=0x10
[ 0.862628] stmmac - user ID: 0x10, Synopsys ID: 0x35
[ 0.862678]Normal descriptors
[ 0.862689]Ring mode enabled
[ 0.862699]DMA HW capability register supported
[ 0.862711]RX Checksum Offload Engine supported (type 2)
[ 0.862722]TX Checksum insertion supported
[ 0.862731]Wake-Up On Lan supported
[ 0.862775]Enable RX Mitigation via HW Watchdog Timer
[ 0.863190] PPP generic driver version 2.4.2
[ 0.863352] PPP BSD Compression module registered
[ 0.863365] PPP Deflate Compression module registered
[ 0.863388] PPP MPPE Compression module registered
[ 0.863401] NET: Registered protocol family 24
[ 0.863441] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[ 0.863455] CSLIP: code copyright 1989 Regents of the University of California.
[ 0.863469] Rockchip WiFi SYS interface (V1.00) ...
[ 0.863557] usbcore: registered new interface driver catc
[ 0.863596] usbcore: registered new interface driver kaweth
[ 0.863610] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[ 0.863646] usbcore: registered new interface driver pegasus
[ 0.863681] usbcore: registered new interface driver rtl8150
[ 0.863716] usbcore: registered new interface driver r8152
[ 0.863727] hso: drivers/net/usb/hso.c: Option Wireless
[ 0.863798] usbcore: registered new interface driver hso
[ 0.863841] usbcore: registered new interface driver asix
[ 0.863879] usbcore: registered new interface driver ax88179_178a
[ 0.863916] usbcore: registered new interface driver cdc_ether
[ 0.863952] usbcore: registered new interface driver cdc_eem
[ 0.863986] usbcore: registered new interface driver dm9601
[ 0.864021] usbcore: registered new interface driver dm9620
[ 0.864078] usbcore: registered new interface driver smsc75xx
[ 0.864124] usbcore: registered new interface driver smsc95xx
[ 0.864160] usbcore: registered new interface driver gl620a
[ 0.864196] usbcore: registered new interface driver net1080
[ 0.864231] usbcore: registered new interface driver plusb
[ 0.864268] usbcore: registered new interface driver rndis_host
[ 0.864308] usbcore: registered new interface driver cdc_subset
[ 0.864345] usbcore: registered new interface driver zaurus
[ 0.864383] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[ 0.864442] usbcore: registered new interface driver int51x1
[ 0.864478] usbcore: registered new interface driver kalmia
[ 0.864514] usbcore: registered new interface driver ipheth
[ 0.864556] usbcore: registered new interface driver sierra_net
[ 0.864599] usbcore: registered new interface driver cx82310_eth
[ 0.864646] usbcore: registered new interface driver cdc_ncm
[ 0.864683] usbcore: registered new interface driver qmi_wwan
[ 0.864719] usbcore: registered new interface driver cdc_mbim
[ 0.864732] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.867123] ehci_rk_probe f1a00000 f1a00010
[ 0.867142] rockchip_ehci_host ff500000.usb: Rockchip On-Chip EHCI Host Controller
[ 0.867174] rockchip_ehci_host ff500000.usb: new USB bus registered, assigned bus number 1
[ 0.867516] rockchip_ehci_host ff500000.usb: irq 56, io mem 0xff500000
[ 0.882352] rockchip_ehci_host ff500000.usb: USB 0.0 started, EHCI 1.00
[ 0.882453] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.882471] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.882487] usb usb1: Product: Rockchip On-Chip EHCI Host Controller
[ 0.882501] usb usb1: Manufacturer: Linux 3.10.0 ehci_hcd
[ 0.882515] usb usb1: SerialNumber: ff500000.usb
[ 0.882935] hub 1-0:1.0: USB hub found
[ 0.882962] hub 1-0:1.0: 1 port detected
[ 0.911861] ehci_rk_probe ok
[ 0.912012] usbcore: registered new interface driver cdc_acm
[ 0.912026] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 0.912079] usbcore: registered new interface driver usblp
[ 0.912121] usbcore: registered new interface driver cdc_wdm
[ 0.912188] usbcore: registered new interface driver usb-storage
[ 0.912227] usbcore: registered new interface driver ums-alauda
[ 0.912264] usbcore: registered new interface driver ums-cypress
[ 0.912300] usbcore: registered new interface driver ums-datafab
[ 0.912336] usbcore: registered new interface driver ums_eneub6250
[ 0.912371] usbcore: registered new interface driver ums-freecom
[ 0.912408] usbcore: registered new interface driver ums-isd200
[ 0.912443] usbcore: registered new interface driver ums-jumpshot
[ 0.912484] usbcore: registered new interface driver ums-karma
[ 0.912525] usbcore: registered new interface driver ums-onetouch
[ 0.912563] usbcore: registered new interface driver ums-sddr09
[ 0.912600] usbcore: registered new interface driver ums-sddr55
[ 0.912636] usbcore: registered new interface driver ums-usbat
[ 0.912723] usbcore: registered new interface driver usbserial
[ 0.912763] usbcore: registered new interface driver usbserial_generic
[ 0.912796] usbserial: USB Serial support registered for generic
[ 0.912835] usbcore: registered new interface driver option
[ 0.912871] usbserial: USB Serial support registered for GSM modem (1-port)
[ 0.912943] usbcore: registered new interface driver trancevibrator
[ 0.912956] usb20_otg: version 3.10a 21-DEC-2012
[ 0.913367] f1a80040
[ 0.913381] Core Release: 3.10a
[ 0.913393] Setting default values for core params
[ 0.913553] Using Buffer DMA mode
[ 0.913565] Periodic Transfer Interrupt Enhancement - disabled
[ 0.913577] Multiprocessor Interrupt Enhancement - disabled
[ 0.913589] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 0.913600] ^^^^^^^^^^^^^^^^^Device Mode
[ 0.913616] Dedicated Tx FIFOs mode
[ 0.913636] pcd_init otg_dev = ed9a2580
[ 0.913796] usb20_otg ff580000.usb: DWC OTG Controller
[ 0.913825] usb20_otg ff580000.usb: new USB bus registered, assigned bus number 2
[ 0.913859] usb20_otg ff580000.usb: irq 55, io mem 0x00000000
[ 0.913923] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.913940] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.913955] usb usb2: Product: DWC OTG Controller
[ 0.913968] usb usb2: Manufacturer: Linux 3.10.0 dwc_otg_hcd
[ 0.913981] usb usb2: SerialNumber: ff580000.usb
[ 0.914385] hub 2-0:1.0: USB hub found
[ 0.914409] hub 2-0:1.0: 1 port detected
[ 0.914689] usb20_host: version 3.10a 21-DEC-2012
[ 0.917130] f1b00040
[ 0.917143] Core Release: 3.10a
[ 0.917153] Setting default values for core params
[ 0.917275] Using Buffer DMA mode
[ 0.917286] Periodic Transfer Interrupt Enhancement - disabled
[ 0.917297] Multiprocessor Interrupt Enhancement - disabled
[ 0.917309] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 0.917320] ^^^^^^^^^^^^^^^^^^Host Mode
[ 0.917346] usb20_host ff540000.usb: DWC OTG Controller
[ 0.917372] usb20_host ff540000.usb: new USB bus registered, assigned bus number 3
[ 0.917407] usb20_host ff540000.usb: irq 57, io mem 0x00000000
[ 0.917500] Init: Power Port (0)
[ 0.917559] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.917576] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.917590] usb usb3: Product: DWC OTG Controller
[ 0.917603] usb usb3: Manufacturer: Linux 3.10.0 dwc_otg_hcd
[ 0.917616] usb usb3: SerialNumber: ff540000.usb
[ 0.917988] hub 3-0:1.0: USB hub found
[ 0.918010] hub 3-0:1.0: 1 port detected
[ 0.918544] .. rk pwm remotectl v1.0 init
[ 0.918640] remotectl probe j=0x0
[ 0.918796] input: ff680000.pwm as /devices/ff680000.pwm/input/input0
[ 0.918993] pwm enable val=0x646205
[ 0.919271] usbcore: registered new interface driver xpad
[ 0.919322] usbcore: registered new interface driver usb_acecad
[ 0.919364] usbcore: registered new interface driver aiptek
[ 0.919406] usbcore: registered new interface driver gtco
[ 0.919454] usbcore: registered new interface driver hanwang
[ 0.919497] usbcore: registered new interface driver kbtab
[ 0.919545] usbcore: registered new interface driver wacom
[ 0.919902] sensor_register_slave:mma8452,id=17
[ 0.919917] sensor_register_slave:cm3217,id=44
[ 0.919929] sensor_register_slave:cm3218,id=45
[ 0.924710] rtc_hym8563 0-0051: rtc core: registered hym8563 as rtc0
[ 0.924762] i2c /dev entries driver
[ 0.925453] IR NEC protocol handler initialized
[ 0.925467] IR RC5(x) protocol handler initialized
[ 0.925478] IR RC6 protocol handler initialized
[ 0.925488] IR JVC protocol handler initialized
[ 0.925498] IR Sony protocol handler initialized
[ 0.925509] IR RC5 (streamzap) protocol handler initialized
[ 0.925519] IR SANYO protocol handler initialized
[ 0.925529] IR MCE Keyboard/mouse protocol handler initialized
[ 0.925622] usbcore: registered new interface driver uvcvideo
[ 0.925635] USB Video Class driver (1.1.1)
[ 0.926376] rockchip_temp_probe,line=362
[ 0.926717] tsadc ff280000.tsadc: initialized
[ 0.927105] device-mapper: uevent: version 1.0.3
[ 0.927358] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[ 0.927654] Bluetooth: HCI UART driver ver 2.2
[ 0.927670] Bluetooth: HCI H4 protocol initialized
[ 0.927682] Bluetooth: HCILL protocol initialized
[ 0.930745] cpufreq version 1.0, suspend freq 816 MHz
[ 0.930936] cpuidle: using governor ladder
[ 0.930951] cpuidle: using governor menu
[ 0.930988] Synopsys Designware Multimedia Card Interface Driver
[ 0.931236] dwmmc_rockchip ff0f0000.rksdmmc: Version ID is 270a
[ 0.931565] dwmmc_rockchip ff0f0000.rksdmmc: Using internal DMA controller.
[ 0.931728] 3230..dw_mci_init_slot: fmin=400000, fmax=100000000
[ 0.931745] Line3235..dw_mci_init_slot: The rk_sdmmc Ver 1.12 2014-07-08
[ 0.931873] 1357..dw_mci_set_ios:no card.
[ 0.951211] 1357..dw_mci_set_ios:no card.
[ 0.970921] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out 800000Hz for init
[ 0.970942] dwmmc_rockchip ff0f0000.rksdmmc: DW MMC controller at irq 67, 32 bit host data width, 256 deep fifo
[ 0.970955] dwmmc_rockchip ff0f0000.rksdmmc: 1 slots initialized
[ 0.971164] dwmmc_rockchip ff0c0000.rksdmmc: Version ID is 270a
[ 0.972031] dwmmc_rockchip ff0c0000.rksdmmc: Using internal DMA controller.
[ 0.972149] 3224..dw_mci_init_slot: fmin=300000, fmax=50000000
[ 0.972566] 1357..dw_mci_set_ios:no card.
[ 0.990575] 1357..dw_mci_set_ios:no card.
[ 1.003034] mmc0: BKOPS_EN bit is not set
[ 1.004920] rk_sdmmc: BOOT Bus speed=0Hz,Bus width=8bits.
[ 1.007211] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0)
[ 1.007234] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out normal clock
[ 1.010394] dwmmc_rockchip ff0c0000.rksdmmc: DW MMC controller at irq 64, 32 bit host data width, 256 deep fifo
[ 1.010407] dwmmc_rockchip ff0c0000.rksdmmc: 1 slots initialized
[ 1.010670] dwmmc_rockchip ff0d0000.rksdmmc: Version ID is 270a
[ 1.010842] dwmmc_rockchip ff0d0000.rksdmmc: Using internal DMA controller.
[ 1.010964] 3230..dw_mci_init_slot: fmin=200000, fmax=50000000
[ 1.011046] 1357..dw_mci_set_ios:no card.
[ 1.022242] rk_sdmmc: BOOT
[ 1.022242]execute tuning: candidates_degree = SDMMC_SHIFT_DEGREE_0SDMMC_SHIFT_DEGREE_90SDMMC_SHIFT_DEGREE_180SDMMC_SHIFT_DEGREE_INVALID
[ 1.022344] mmc0: new HS200 MMC card at address 0001
[ 1.022603] mmcblk0: mmc0:0001 AWMB3R 14.5 GiB
[ 1.022929] uboot: 0x000400000 -- 0x000800000 (4 MB)
[ 1.022941] misc: 0x000800000 -- 0x000c00000 (4 MB)
[ 1.022950] resource: 0x000c00000 -- 0x001c00000 (16 MB)
[ 1.022959] kernel: 0x001c00000 -- 0x002c00000 (16 MB)
[ 1.022968] boot: 0x002c00000 -- 0x004c00000 (32 MB)
[ 1.022977] recovery: 0x004c00000 -- 0x006c00000 (32 MB)
[ 1.022985] backup: 0x006c00000 -- 0x00a000000 (52 MB)
[ 1.022994] cache: 0x00a000000 -- 0x012000000 (128 MB)
[ 1.023003] kpanic: 0x012000000 -- 0x012400000 (4 MB)
[ 1.023012] system: 0x012400000 -- 0x042400000 (768 MB)
[ 1.023020] metadata: 0x042400000 -- 0x042800000 (4 MB)
[ 1.023029] userdata: 0x042800000 -- 0x082800000 (1024 MB)
[ 1.023037] radical_update: 0x082800000 -- 0x086800000 (64 MB)
[ 1.023046] user: 0x086800000 -- 0x3a3a00000 (12754 MB)
[ 1.023077]mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p141357..dw_mci_set_ios:no card.
[ 1.029947] 1357..dw_mci_set_ios:no card.
[ 1.049625] 1357..dw_mci_set_ios:no card.
[ 1.049809] dwmmc_rockchip ff0d0000.rksdmmc: DW MMC controller at irq 65, 32 bit host data width, 256 deep fifo
[ 1.049823] dwmmc_rockchip ff0d0000.rksdmmc: 1 slots initialized
[ 1.050074] leds-gpio leds.31: pins are not configured from the driver
[ 1.050310] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.051591] usbcore: registered new interface driver usbhid
[ 1.051601] usbhid: USB HID core driver
[ 1.051904] ashmem: initialized
[ 1.052009] logger: created 256K log 'log_main'
[ 1.052108] logger: created 256K log 'log_events'
[ 1.052201] logger: created 256K log 'log_radio'
[ 1.052293] logger: created 256K log 'log_system'
[ 1.053286] input: rk29-keypad as /devices/ff100000.adc/key.34/input/input1
[ 1.053866] rockchip-pinctrl ff770000.pinctrl: pin gpio6-8 already requested by ; cannot claim for 2-0010
[ 1.053882] rockchip-pinctrl ff770000.pinctrl: pin-200 (2-0010) status -22
[ 1.053894] rockchip-pinctrl ff770000.pinctrl: could not request pin 200 on device rockchip-pinctrl
[ 1.053905] ES8323 2-0010: Error applying setting, reverse things back
[ 1.054199] es8323 probe i2c recv ok
[ 1.054407] i2c-core: driver using legacy suspend method
[ 1.054416] i2c-core: driver using legacy resume method
[ 1.054719] rockchip-hdmi-spdif rockchip-hdmi-spdif.27: ASoC: CPU DAI (null) not registered
[ 1.054749] rockchip_hdmi_spdif_audio_probe() register card failed:-517
[ 1.054768] platform rockchip-hdmi-spdif.27: Driver rockchip-hdmi-spdif requests probe deferral
[ 1.054998] es8323_probe
[ 1.055091] es8323_probe:register ISR (irq=194)
[ 1.689581] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> NULL --> Left Line Mux
[ 1.689594] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> NULL -> Left Line Mux
[ 1.689604] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> NULL --> Left Line Mux
[ 1.689613] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> NULL -> Left Line Mux
[ 1.689623] ES8323 2-0010: ASoC: no dapm match for Left PGA Mux --> NULL --> Left Line Mux
[ 1.689631] ES8323 2-0010: ASoC: Failed to add route Left PGA Mux -> NULL -> Left Line Mux
[ 1.689641] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> NULL --> Right Line Mux
[ 1.689649] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> NULL -> Right Line Mux
[ 1.689659] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> NULL --> Right Line Mux
[ 1.689667] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> NULL -> Right Line Mux
[ 1.689677] ES8323 2-0010: ASoC: no dapm match for Right PGA Mux --> NULL --> Right Line Mux
[ 1.689685] ES8323 2-0010: ASoC: Failed to add route Right PGA Mux -> NULL -> Right Line Mux
[ 1.689696] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> LAMP --> Left PGA Mux
[ 1.689704] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> LAMP -> Left PGA Mux
[ 1.689714] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> LAMP --> Left PGA Mux
[ 1.689723] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> LAMP -> Left PGA Mux
[ 1.689732] ES8323 2-0010: ASoC: no dapm match for Differential Mux --> LAMP --> Left PGA Mux
[ 1.689742] ES8323 2-0010: ASoC: Failed to add route Differential Mux -> LAMP -> Left PGA Mux
[ 1.689751] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> RAMP --> Right PGA Mux
[ 1.689759] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> RAMP -> Right PGA Mux
[ 1.689768] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> RAMP --> Right PGA Mux
[ 1.689776] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> RAMP -> Right PGA Mux
[ 1.689785] ES8323 2-0010: ASoC: no dapm match for Differentish Mu@rk->88AM $ -> Right PGA Mux
[ 1.689793] ES8323 2-0010: ASoC: Failed to add route Differential Mux -> RAMP -> Right PGA Mux
[ 1.689804] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> LAMP --> Differential Mux
[ 1.689812] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> LAMP -> Differential Mux
[ 1.689821] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> RAMP --> Differential Mux
[ 1.689829] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> RAMP -> Differential Mux
[ 1.689839] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> LAMP --> Differential Mux
[ 1.689847] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> LAMP -> Differential Mux
[ 1.689856] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> RAMP --> Differential Mux
[ 1.689864] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> RAMP -> Differential Mux
[ 1.689885] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> LAMP --> Left Line Mux
[ 1.689894] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> LAMP -> Left Line Mux
[ 1.689903] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> LAMP --> Left Line Mux
[ 1.689911] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> LAMP -> Left Line Mux
[ 1.689920] ES8323 2-0010: ASoC: no dapm match for Left PGA Mux --> LAMP --> Left Line Mux
[ 1.689928] ES8323 2-0010: ASoC: Failed to add route Left PGA Mux -> LAMP -> Left Line Mux
[ 1.689937] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> RAMP --> Right Line Mux
[ 1.689946] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> RAMP -> Right Line Mux
[ 1.689955] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> RAMP --> Right Line Mux
[ 1.689963] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> RAMP -> Right Line Mux
[ 1.689972] ES8323 2-0010: ASoC: no dapm match for Right PGA Mux --> RAMP --> Right Line Mux
[ 1.689980] ES8323 2-0010: ASoC: Failed to add route Right PGA Mux -> RAMP -> Right Line Mux
[ 1.690110] ES8323 2-0010: ASoC: mux Right Line Mux has no paths
[ 1.690122] ES8323 2-0010: ASoC: mux Left Line Mux has no paths
[ 1.690133] ES8323 2-0010: ASoC: mux Right PGA Mux has no paths
[ 1.690143] ES8323 2-0010: ASoC: mux Left PGA Mux has no paths
[ 1.690163] ES8323 2-0010: ASoC: mux Differential Mux has no paths
[ 1.692713] Enter::rk29_es8323_init----123
[ 1.696086] rockchip-es8323 rockchip-es8323.29:ES8323 HiFi <-> rockchip-i2s.0 mapping ok
[ 1.698188] u32 classifier
[ 1.698196] Actions configured
[ 1.698207] Netfilter messages via NETLINK v0.30.
[ 1.698262] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 1.698529] ctnetlink v0.93: registering with nfnetlink.
[ 1.698588] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 1.698595] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 1.698812] xt_time: kernel timezone is -0000
[ 1.698980] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.699113] arp_tables: (C) 2002 David S. Miller
[ 1.699145] TCP: cubic registered
[ 1.699152] Initializing XFRM netlink socket
[ 1.699338] NET: Registered protocol family 10
[ 1.699770] mip6: Mobile IPv6
[ 1.699793] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 1.699897] sit: IPv6 over IPv4 tunneling driver
[ 1.700192] NET: Registered protocol family 17
[ 1.700219] NET: Registered protocol family 15
[ 1.700266] Bridge firewalling registered
[ 1.700277] Ebtables v2.0 registered
[ 1.700427] Bluetooth: RFCOMM TTY layer initialized
[ 1.700461] Bluetooth: RFCOMM socket layer initialized
[ 1.700469] Bluetooth: RFCOMM ver 1.11
[ 1.700475] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 1.700481] Bluetooth: BNEP filters: protocol multicast
[ 1.700491] Bluetooth: BNEP socket layer initialized
[ 1.700498] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 1.700507] Bluetooth: HIDP socket layer initialized
[ 1.700532] l2tp_core: L2TP core driver, V2.0
[ 1.700544] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 1.700551] : Enter rfkill_wlan_init
[ 1.700739] : Enter rfkill_wlan_probe
[ 1.700749] wlan_platdata_parse_dt: wifi_chip_type = bcmwifi
[ 1.700756] : wlan_platdata_parse_dt: enable wifi power control.
[ 1.700765] : wlan_platdata_parse_dt: disable wifi io reference voltage control.
[ 1.700773] : wlan_platdata_parse_dt: wifi power controled by gpio.
[ 1.700793] : wlan_platdata_parse_dt: get property: WIFI,poweren_gpio = 156, flags = 0.
[ 1.700812] : wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 158, flags = 0.
[ 1.700820] : rfkill_wlan_probe: init gpio
[ 1.700844] : rockchip_wifi_voltage_select: wifi & sdio reference voltage: 1.8V
[ 1.700882] : Exit rfkill_wlan_probe
[ 1.700928] : Enter rfkill_rk_init
[ 1.701038] : bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 147.
[ 1.701053] : bluetooth_platdata_parse_dt: get property: BT,power_gpio = 155.
[ 1.701065] : bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 157.
[ 1.701078] : bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 154.
[ 1.701091] : bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 159.
[ 1.701134] : Request irq for bt wakeup host
[ 1.701228] : ** disable irq
[ 1.701296] : ap6335 device registered.
[ 1.701896] rk3288-hdmi ff980000.hdmi: rk3288 hdmi probe sucess.
[ 1.702222] VFP support v0.3: implementor 41 architecture 3 part 30 variant d rev 0
[ 1.702242] rk3288_init_suspend
[ 1.702249] rk3288_suspend_init enter
[ 1.702373] rk3288_suspend_init: pm_ctrbits =40017
[ 1.702406] gpio_get_dts_info suspend:8
[ 1.702414] gpio_get_dts_info resume:8
[ 1.702419] rockchip,pmic-suspend_gpios:1007c30 1007c40 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
[ 1.702445] rockchip,pmic-resume_gpios:2007c32 2007c42 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
[ 1.702568] clks_gating_suspend_init:clkgt info ok
[ 1.702642] Registering SWP/SWPB emulation handler
[ 1.702942] ddrfreq: verion 1.2 20140526
[ 1.702953] ddrfreq: normal 456MHz video_1080p 0MHz video_4k 456MHz dualview 0MHz idle 0MHz suspend 200MHz reboot 456MHz
[ 1.702961] ddrfreq: auto-freq=0
[ 1.702967] ddrfreq: auto-freq-table 240MHz
[ 1.702972] ddrfreq: auto-freq-table 324MHz
[ 1.702977] ddrfreq: auto-freq-table 456MHz
[ 1.702983] ddrfreq: auto-freq-table 528MHz
[ 1.704600] act_ldo3: operation not allowed
[ 1.704840] vga_edid_probe: turn on ldo3 done.
[ 1.704865] act_ldo4: operation not allowed
[ 1.705097] vga_edid_probe: turn on ldo done.
[ 1.705119] act_ldo2: operation not allowed
[ 1.705348] vga_edid_probe: turn on ldo2 done.
[ 1.705368] act_ldo8: operation not allowed
[ 1.705597] vga_edid_probe: turn on ldo done.
[ 1.708168] unable to read EDID block.
[ 1.708177] vga-ddc: read and parse edid failed errno:-5.
[ 1.708183] vga_edid_probe: success. 10
[ 1.708287] firefly_vga_get_enable 180, 0
[ 1.708294] firefly_vga_get_status 186
[ 1.708308] firefly_vga_set_enable 159 enable:1
[ 1.708323] firefly_vga_enable 130 start
[ 1.708329] firefly_switch_fb 55
[ 1.708335]
[ 1.708335] rk_fb_switch_screen lcdc_id 0 type 1 enable 1
[ 1.708346] fb0 win id 1 state 1
[ 1.708357] regulator-dummy: disabling
[ 1.708362] rk3288-lcdc lcdc0: lcdc0: dclk:148500000>>fps:60
[ 1.708379] fb1 win id 0 state 0
[ 1.708385] fb2 win id 2 state 0
[ 1.708390] fb3 win id 3 state 0
[ 1.708395] fb4 win id 4 state 0
[ 1.708400]
[ 1.708400] rk_fb_switch_screen lcdc_id 0 type 1 enable 1 done
[ 1.708400]
[ 1.708424] VGA ENABLE
[ 1.708617] rockchip-hdmi-spdif rockchip-hdmi-spdif.27: ASoC: CPU DAI (null) not registered
[ 1.708640] rockchip_hdmi_spdif_audio_probe() register card failed:-517
[ 1.708655] platform rockchip-hdmi-spdif.27: Driver rockchip-hdmi-spdif requests probe deferral
[ 1.708731] pcd_pullup, is_on 0
[ 1.708765] file system registered
[ 1.709332] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 1.709341] android_usb gadget: Number of LUNs=2
[ 1.709348]lun0: LUN: removable file: (no medium)
[ 1.709354]lun1: LUN: removable file: (no medium)
[ 1.709469] android_usb gadget: android_usb ready
[ 1.709543] sensor_init: Probe name sensors
[ 1.709557] sensor-dev.c v1.4 add angle calculation support between two gsensors 2013-09-01
[ 1.710084] rtc_hym8563 0-0051: setting system clock to 2011-01-01 12:01:23 UTC (1293883283)
[ 1.715424] usbcore: registered new interface driver snd-usb-audio
[ 1.715445] ALSA device list:
[ 1.715451] #0: RK_ES8323
[ 1.716702] Freeing unused kernel memory: 2360K (c0a6f000 - c0cbd000)
[ 1.717077] rockchip-hdmi-spdif rockchip-hdmi-spdif.27:rk-hdmi-spdif-hifi <-> rockchip-spdif mapping ok
[ 1.721249] SELinux:Permission attach_queue in class tun_socket not defined in policy.
[ 1.721261] SELinux: the above unknown classes and permissions will be denied
[ 1.977549] type=1403 audit(1293883283.760:2): policy loaded auid=4294967295 ses=4294967295
[ 1.977649] SELinux: Loaded policy from /sepolicy
[ 1.979073] type=1404 audit(1293883283.760:3): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
[ 2.889707] dwc_otg_hcd_enable, enable host controller
[ 2.919239] init: init.rk30board.bootmode.emmc.rc: 8: invalid command '/devices/ff0f0000.rksdmmc/mmc_host/mmc'
[ 2.919256] init: init.rk30board.bootmode.emmc.rc: 9: invalid command '/devices/ff0c0000.rksdmmc/mmc_host/mmc'
[ 2.919268] init: init.rk30board.bootmode.emmc.rc: 10: invalid command '/devices/ff580000.usb'
[ 2.919279] init: init.rk30board.bootmode.emmc.rc: 11: invalid command '/devices/ff580000.usb'
[ 2.919289] init: init.rk30board.bootmode.emmc.rc: 12: invalid command '/devices/ff500000.usb'
[ 2.919299] init: init.rk30board.bootmode.emmc.rc: 13: invalid command '/devices/ff500000.usb'
[ 2.919309] init: init.rk30board.bootmode.emmc.rc: 14: invalid command '/devices/ff540000.usb'
[ 2.919318] init: init.rk30board.bootmode.emmc.rc: 15: invalid command '/devices/ff540000.usb'
[ 2.919604] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
[ 2.970014] init: /dev/hw_random not found
[ 2.970071] keychord: using input dev ff680000.pwm for fevent
[ 2.970080] keychord: using input dev rk29-keypad for fevent
[ 2.974829] fs_mgr: parse_link_device : path = NULL
[ 2.974851] fs_mgr: parse_link_device : path = NULL
[ 2.974880] fs_mgr: parse_link_device : path = NULL
[ 2.974897] fs_mgr: parse_link_device : path = NULL
[ 2.974914] fs_mgr: parse_link_device : path = NULL
[ 2.974930] fs_mgr: parse_link_device : path = NULL
[ 2.974945] fs_mgr: parse_link_device : path = NULL
[ 2.974960] fs_mgr: parse_link_device : path = NULL
[ 2.975036] fs_mgr: ---------------resize_fs blk_dev /dev/block/platform/ff0f0000.rksdmmc/by-name/system, type ext4fs_mgr: Running /sbin/resize2fs on /dev/block/platform/ff0f0000.rksdmmc/by-name/system
[ 2.975793] resize2fs: resize2fs 1.41.14 (22-Dec-2010)resize2fs: The filesystem is already 196608 blocks long.Nothing to do!resize2fs:
[ 2.982575] EXT4-fs (mmcblk0p10): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
[ 2.993186] EXT4-fs (mmcblk0p8): recovery complete
[ 2.993667] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard
[ 2.995531] EXT4-fs (mmcblk0p11): recovery complete
[ 2.995542] EXT4-fs (mmcblk0p11): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard
[ 3.004252] Using Buffer DMA mode
[ 3.004261] Periodic Transfer Interrupt Enhancement - disabled
[ 3.004267] Multiprocessor Interrupt Enhancement - disabled
[ 3.004273] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 3.004279] ^^^^^^^^^^^^^^^^^^Host Mode
[ 3.007039] EXT4-fs (mmcblk0p12): recovery complete
[ 3.007533] EXT4-fs (mmcblk0p12): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard
[ 3.012815] drmboot: version magic '3.0.36+ SMP preempt mod_unload ARMv7 ' should be '3.10.0 SMP preempt mod_unload ARMv7 p2v8 '
[ 3.017966] mali pd enabled
[ 3.017978] clk enabled
[ 3.017988] MALI_DVFS_STEP=4,div_dvfs=10
[ 3.017995] mali_dvfs_infotbl.clock=198000,min_threshold=0,max_threshold=70
[ 3.018002] mali_dvfs_infotbl.clock=297000,min_threshold=70,max_threshold=80
[ 3.018009] mali_dvfs_infotbl.clock=313000,min_threshold=86,max_threshold=90
[ 3.018016] mali_dvfs_infotbl.clock=480000,min_threshold=88,max_threshold=100
[ 3.018115] turn on mali power
[ 3.018137] mali ffa30000.gpu: GPU identified as 0x0750 r0p0 status 1
[ 3.018512] mali ffa30000.gpu: Probed as mali0
[ 3.020793] rk29_ipp: version magic '3.0.8+ SMP preempt mod_unload ARMv7 ' should be '3.10.0 SMP preempt mod_unload ARMv7 p2v8 '
[ 3.029003] init: /dev/hw_random not found
[ 3.034672] binder: 136:136 transaction failed 29189, size 0-0
[ 3.035219] init: cannot find '/system/vendor/bin/pvrsrvctl', disabling 'pvrsrvctl'
[ 3.037641] init: cannot find '/system/bin/rild3', disabling 'ril-daemon3'
[ 3.039202] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
[ 3.040154] init: cannot find '/system/bin/bindvbplayservice', disabling 'dvbdataserv'
[ 3.040538] init: cannot find '/system/bin/chrome.sh', disabling 'chrome'
[ 3.040849] init: cannot find '/system/bin/bplus_helper', disabling 'bplus_helper'
[ 3.047219] Init: Power Port (0)
[ 3.078924] init: property 'ro.serialno' doesn't exist while expanding '${ro.serialno}'
[ 3.078943] init: cannot expand '${ro.serialno}' while writing to '/sys/class/android_usb/android0/iSerial'
[ 3.079096] init: using deprecated syntax for specifying property 'ro.product.usbfactory', use ${name} instead
[ 3.101251] =======================================================
[ 3.101262] ==== Launching Wi-Fi driver! (Powered by Rockchip) ====
[ 3.101268] =======================================================
[ 3.101274]WiFi driver (Powered by Rockchip,Ver 4.80.WFD.OOB) init.
[ 3.101298] ======== PULL WL_REG_ON HIGH! ========
[ 3.101304] : rockchip_wifi_power: 1
[ 3.101310] : rockchip_wifi_ref_voltage: 1
[ 3.101316] : rockchip_wifi_ref_voltage: wifi io reference voltage control is disabled.
[ 3.177383] rk3288-lcdc lcdc0: lcdc0: dclk:148500000>>fps:60
[ 3.179147] fs_mgr: parse_link_device : path = NULL
[ 3.179173] fs_mgr: parse_link_device : path = NULL
[ 3.179191] fs_mgr: parse_link_device : path = NULL
[ 3.179208] fs_mgr: parse_link_device : path = NULL
[ 3.179224] fs_mgr: parse_link_device : path = NULL
[ 3.179241] fs_mgr: parse_link_device : path = NULL
[ 3.179269] fs_mgr: parse_link_device : path = NULL
[ 3.179288] fs_mgr: parse_link_device : path = NULL
[ 3.204583] : wifi turn on power. 156
[ 3.204596] mmc2:mmc host rescan start!
[ 3.204607] =========== WLAN placed in POWER ON ========
[ 3.204626] bcmsdh_register: Linux Kernel SDIO/MMC Driver
[ 3.204707]
[ 3.204707] Dongle Host Driver, version 1.88.45.3 (r420671)
[ 3.204707] Compiled in drivers/net/wireless/bcmdhd on Nov 20 2014 at 17:23:41
[ 3.275416] firefly_vga_get_enable 180, 1
[ 3.275506] firefly_vga_get_status 186
[ 3.304691] init: property 'sys.powerctl' doesn't exist while expanding '${sys.powerctl}'
[ 3.304720] init: powerctl: cannot expand '${sys.powerctl}'
[ 3.3047
DDR Version 1.00 20141007
In
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Memory OK
Memory OK
OUT
U-Boot 2014.10-RK3288-02 (Oct 30 2014 - 09:27:41)
CPU: rk3288
CPU's clock information:
arm pll = 600000000HZ
periph pll = 300000000HZ
ddr pll = 200000000HZ
codec pll = 594000000HZ
Board: Rockchip platform Board
DRAM:Found dram banks:1
Adding bank:0000000000000000(0000000080000000)
128 MiB
storage init OK!
Using default environment
GetParam
check parameter success
Unknow param: MACHINE_MODEL:rk30sdk!
Unknow param: MACHINE_ID:007!
Unknow param: MANUFACTURER:RK30SDK!
Unknow param: PWR_HLD: 0,0,A,0,1!
failed to prepare fdt from boot!
power key: bank-0 pin-5
can't find dts node for ricoh619
pmic:act8846
Can't find dts node for fuel guage cw201x
SecureBootEn = 0, SecureBootLock = 0
#Boot ver: 2014-10-30#2.17
sn:1006110001000029
no fuel gauge found
no fuel gauge found
read logo_on switch from dts
checkKey
vbus = 0
no fuel gauge found
Hit any key to stop autoboot:0
failed to load fdt from boot!
kernel @ 0x02000000 (0x005f3cf0)
ramdisk@ 0x059fc000 (0x00120f04)
Secure Boot state: 0
bootrk: do_bootm_linux...
Loading Device Tree to 0561c000, end 05636f1c ... OK
Add bank:0000000000000000, 0000000080000000
Starting kernel ...
<hit enter to activate fiq debugger>
[ 0.000000] Booting Linux on physical CPU 0x500
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.10.0 (leo@ubuntu) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #1 SMP PREEMPT Thu Nov 20 17:24:20 CST 2014
[ 0.000000] CPU: ARMv7 Processor revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Rockchip RK3288 (Flattened Device Tree), model: rockchip,rk3288
[ 0.000000] rockchip_ion_reserve
[ 0.000000] cma: CMA: reserved 16 MiB at 2e800000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] PERCPU: Embedded 9 pages/cpu @c1eac000 s14016 r8192 d14656 u36864
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.Total pages: 522768
[ 0.000000] Kernel command line: console=ttyFIQ0 androidboot.hardware=rk30board androidboot.console=ttyFIQ0 board.ap_has_alsa=0 init=/initmtdparts=rk29xxnand:0x00002000@0x00002000(uboot),0x00002000@0x00004000(misc),0x00008000@0x00006000(resource),0x00008000@0x0000e000(kernel),0x00010000@0x00016000(boot),0x00010000@0x00026000(recovery),0x0001a000@0x00036000(backup),0x00040000@0x00050000(cache),0x00002000@0x00090000(kpanic),0x00180000@0x00092000(system),0x00002000@0x00212000(metadata),0x00200000@0x00214000(userdata),0x00020000@0x00414000(radical_update),-@0x00434000(user) storagemedia=emmc loader.timestamp=2014-10-30_09:27:41 androidboot.serialno=1006110001000029
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 2048MB = 2048MB total
[ 0.000000] Memory: 2047124k/2047124k available, 50028k reserved, 1318912K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector: 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap: 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem: 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 (14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0a6ea3c (10651 kB)
[ 0.000000] .init : 0xc0a6f000 - 0xc0cbd6c0 (2362 kB)
[ 0.000000] .data : 0xc0cbe000 - 0xc0d5ab48 ( 627 kB)
[ 0.000000] .bss : 0xc0d5ab48 - 0xc0e74d84 (1129 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000]RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] rk_clk_tree_init start! cru base = 0xfed00000
[ 0.000000] rk_get_uboot_display_flag: uboot_logo_on = 0
[ 0.000000] rkclk_init_clks: cnt_parent = 7
[ 0.000000] rkclk_init_clks: cnt_rate = 32
[ 0.000000] Architected local timer running at 24.00MHz (phys).
[ 0.000000] Switching to timer-based delay loop
[ 0.000000] sched_clock: ARM arch timer >56 bits at 24000kHz, resolution 41ns
[ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
[ 0.443972] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.443988] pid_max: default: 32768 minimum: 301
[ 0.444093] Security Framework initialized
[ 0.444110] SELinux:Initializing.
[ 0.444185] Mount-cache hash table entries: 512
[ 0.444823] Initializing cgroup subsys debug
[ 0.444838] Initializing cgroup subsys freezer
[ 0.444866] CPU: Testing write buffer coherency: ok
[ 0.445169] /cpus/cpu@0 missing clock-frequency property
[ 0.445181] /cpus/cpu@1 missing clock-frequency property
[ 0.445190] /cpus/cpu@2 missing clock-frequency property
[ 0.445199] /cpus/cpu@3 missing clock-frequency property
[ 0.445247] CPU0: thread -1, cpu 0, socket 5, mpidr 80000500
[ 0.445297] Setting up static identity map for 0xc0785160 - 0xc07851b8
[ 0.447597] last_log: 0x2e100000 map to 0xf0004000 and copy to 0xf0086000, size 0x80000 early 0x1368 (version 3.0)
[ 0.522678] CPU1: Booted secondary processor
[ 0.522711] CPU1: thread -1, cpu 1, socket 5, mpidr 80000501
[ 0.542368] CPU2: Booted secondary processor
[ 0.542393] CPU2: thread -1, cpu 2, socket 5, mpidr 80000502
[ 0.562066] CPU3: Booted secondary processor
[ 0.562090] CPU3: thread -1, cpu 3, socket 5, mpidr 80000503
[ 0.562192] Brought up 4 CPUs
[ 0.562220] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[ 0.562229] CPU: All CPU(s) started in SVC mode.
[ 0.562965] devtmpfs: initialized
[ 0.568162] pinctrl core: initialized pinctrl subsystem
[ 0.568406] regulator-dummy: no parameters
[ 0.568909] NET: Registered protocol family 16
[ 0.570455] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.570711] ion_snapshot: 0x2e1b0000 map to 0xf0107000 and copy to 0xc0e503d4 (version 0.1)
[ 0.571012] Registered FIQ tty driver
[ 0.572186] console enabled
[ 0.572394] Registered fiq debugger ttyFIQ0
[ 0.572901] rockchip_get_bank_data:name=base start=0xff750000,end=0xff7500ff
[ 0.572926] rockchip_get_bank_data:name=mux_bank0 start=0xff730084,end=0xff73008f
[ 0.572946] rockchip_get_bank_data:name=pull_bank0 start=0xff730064,end=0xff73006f
[ 0.572974] rockchip_get_bank_data:name=drv_bank0 start=0xff730070,end=0xff73007b
[ 0.573070] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio1@ff780000 start=0xff780000,end=0xff7800ff
[ 0.573137] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio2@ff790000 start=0xff790000,end=0xff7900ff
[ 0.573200] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio3@ff7a0000 start=0xff7a0000,end=0xff7a00ff
[ 0.573261] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio4@ff7b0000 start=0xff7b0000,end=0xff7b00ff
[ 0.573323] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio5@ff7c0000 start=0xff7c0000,end=0xff7c00ff
[ 0.573384] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio6@ff7d0000 start=0xff7d0000,end=0xff7d00ff
[ 0.573446] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio7@ff7e0000 start=0xff7e0000,end=0xff7e00ff
[ 0.573508] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio8@ff7f0000 start=0xff7f0000,end=0xff7f00ff
[ 0.573578] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio15@ff7f2000 start=0xff7f2000,end=0xff7f20ff
[ 0.573643] rockchip_pinctrl_probe:name=RK3288-GPIO,type=3
[ 0.573659] rockchip_pinctrl_probe:name=base start=0xff770000,end=0xff77013f
[ 0.573674] rockchip_pinctrl_probe:name=pull start=0xff770140,end=0xff7701bf
[ 0.573688] rockchip_pinctrl_probe:name=drv start=0xff7701c0,end=0xff77023f
[ 0.574184] rockchip_interrupts_register:bank_num=7
[ 0.576084] of_get_gpio_init_config:gpio = 256, value = 0
[ 0.576108] of_get_gpio_init_config:gpio = 233, value = 0
[ 0.576131] of_get_gpio_init_config:gpio = 136, value = 0
[ 0.576205] rockchip_pinctrl_probe:init ok
[ 0.581836] rk_iommu ff900800.iep_mmu: (iep) Enter
[ 0.581958] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.581974] rk_iommu ff900800.iep_mmu: (iep) Initialized
[ 0.582138] rk_iommu ff950800.vip_mmu: (vip) Enter
[ 0.582246] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.582262] rk_iommu ff950800.vip_mmu: (vip) Initialized
[ 0.582420] rk_iommu ff930300.vopb_mmu: (vopb) Enter
[ 0.582526] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.582541] rk_iommu ff930300.vopb_mmu: (vopb) Initialized
[ 0.582697] rk_iommu ff940300.vopl_mmu: (vopl) Enter
[ 0.582806] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.582822] rk_iommu ff940300.vopl_mmu: (vopl) Initialized
[ 0.582982] rk_iommu ff9c0440.hevc_mmu: (hevc) Enter
[ 0.583107] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.583122] rk_iommu ff9c0440.hevc_mmu: (hevc) Initialized
[ 0.583279] rk_iommu ff9a0800.vpu_mmu: (vpu) Enter
[ 0.583384] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.583400] rk_iommu ff9a0800.vpu_mmu: (vpu) Initialized
[ 0.583568] rk_iommu ff914000.isp_mmu: (isp_mmu) Enter
[ 0.583692] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.583707] rk_iommu ff914000.isp_mmu: (isp_mmu) Initialized
[ 0.585314] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.585331] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.585536] DDR DEBUG: version 1.00 20140603
[ 0.585568] DDR DEBUG: Channel a:
[ 0.585578] DDR DEBUG: DDR3 Device
[ 0.585594] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Total Capability=1024MB
[ 0.585606] DDR DEBUG: Channel b:
[ 0.585615] DDR DEBUG: DDR3 Device
[ 0.585628] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Total Capability=1024MB
[ 0.585641] DDR DEBUG: addr=0xd60000
[ 0.585652] DDR DEBUG: stride=9, size=256, halfcap=40000000
[ 0.585663] DDR DEBUG: socAddr=0xd60000, socAddr=0xd60100
[ 0.585675] DDR DEBUG: chAddr=0xd60000, chAddr=0xd60000
[ 0.585688] DDR DEBUG: dtar=0x1ac000, dtar=0x1ac000
[ 0.585744] DDR DEBUG: init success!!! freq=200MHz
[ 0.585753] DDR DEBUG: Channel a:
[ 0.585767] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.585784] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.585801] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.585817] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.585833] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0
[ 0.585845] DDR DEBUG: DRV Pull-Up=0x19, DRV Pull-Dwn=0x19
[ 0.585857] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2
[ 0.585866] DDR DEBUG: Channel b:
[ 0.585879] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.585895] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.585911] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.585927] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.585942] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0
[ 0.585954] DDR DEBUG: DRV Pull-Up=0x19, DRV Pull-Dwn=0x19
[ 0.585965] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2
[ 0.606797] bio: create slab <bio-0> at 0
[ 0.607433] Enter firefly_noatx8_init
[ 0.607593] firefly_noatx8_probe 51
[ 0.607817] SCSI subsystem initialized
[ 0.607970] usbcore: registered new interface driver usbfs
[ 0.608015] usbcore: registered new interface driver hub
[ 0.608109] usbcore: registered new device driver usb
[ 0.609087] rockchip_i2c ff650000.i2c: i2c-0: Rockchip I2C adapter
[ 0.610518] rockchip_i2c ff140000.i2c: i2c-1: Rockchip I2C adapter
[ 0.610964] rockchip_i2c ff660000.i2c: i2c-2: Rockchip I2C adapter
[ 0.611445] rockchip_i2c ff150000.i2c: i2c-3: Rockchip I2C adapter
[ 0.611690] rockchip_i2c ff160000.i2c: i2c-4: Rockchip I2C adapter
[ 0.612556] media: Linux media interface: v0.10
[ 0.612599] Linux video capture interface: v2.00
[ 0.612648] pps_core: LinuxPPS API ver. 1 registered
[ 0.612661] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.612685] PTP clock support registered
[ 0.612912] rockchip_ion_parse_dt: num_heaps = 1
[ 0.612930] 0:03vmalloc0x(null)
[ 0.613193] Rockchip ion module is successfully loaded (v1.0)
[ 0.613359] Advanced Linux Sound Architecture Driver Initialized.
[ 0.613747] Bluetooth: Core ver 2.16
[ 0.613786] NET: Registered protocol family 31
[ 0.613798] Bluetooth: HCI device and connection manager initialized
[ 0.613816] Bluetooth: HCI socket layer initialized
[ 0.613832] Bluetooth: L2CAP socket layer initialized
[ 0.613862] Bluetooth: SCO socket layer initialized
[ 0.614091] cfg80211: Calling CRDA to update world regulatory domain
[ 0.614681] act8846_i2c_probe,line=898
[ 0.615658] act8846_parse_dt,line=746
[ 0.616093] act8846_i2c_probe: act8846_pmic_hold=1
[ 0.616115] act8846_i2c_probe: act8846_pmic_sleep=1
[ 0.616133] act8846_i2c_probe: act8846_pmic_cpu_det_gpio=1
[ 0.616151] act8846_i2c_probe: act8846_pmic_usb_hub_reset_gpio=1
[ 0.617966] act_dcdc1: 1200 mV
[ 0.620660] vccio: 3300 mV
[ 0.622515] vdd_logic: 700 <--> 1500 mV at 1125 mV
[ 0.625197] act_dcdc4: 2000 mV
[ 0.626440] vccio_sd: 1800 <--> 3300 mV at 3300 mV
[ 0.628494] act_ldo2: 1050 mV
[ 0.630556] act_ldo3: 1800 mV
[ 0.632616] act_ldo4: 3300 mV
[ 0.634664] act_ldo5: 3300 mV
[ 0.636719] act_ldo6: 1100 mV
[ 0.638789] vcc_18: 1800 mV
[ 0.640854] act_ldo8: 1850 mV
[ 0.645560] vdd_arm: 712 <--> 1500 mV at 1350 mV
[ 0.650206] vdd_gpu: 712 <--> 1500 mV at 1150 mV
[ 0.650645] rk808_i2c_probe,line=1368
[ 0.651967] The device is not rk808 -11
[ 0.652052] rk808: probe of 0-001b failed with error -11
[ 0.653416] Switching to clocksource arch_sys_counter
[ 0.674974] rk-fb rockchip-fb: rk fb ion client create success!
[ 0.675002] rk-fb rockchip-fb: rockchip framebuffer driver probe
[ 0.675482] rk-screen rk_screen.9: rockchip screen probe success
[ 0.675769] rk32-lvds rk32-lvds: rk32 lvds driver probe success
[ 0.675993] rk32-edp ff970000.edp: screen is not edp!
[ 0.676016] rk32-edp: probe of ff970000.edp failed with error -22
[ 0.676371] rk3288-lcdc lcdc0: can't find power_ctr node for lcdc0
[ 0.676682] graphics fb0: rockchip framebuffer registerd:fb0
[ 0.677095] graphics fb1: rockchip framebuffer registerd:fb1
[ 0.677276] graphics fb2: rockchip framebuffer registerd:fb2
[ 0.677426] graphics fb3: rockchip framebuffer registerd:fb3
[ 0.677581] graphics fb4: rockchip framebuffer registerd:fb4
[ 0.678238] rk_iommu ff930300.vopb_mmu: (vopb) Enabled
[ 0.678394] rk3288-lcdc lcdc0: lcdc0: dclk:148500000>>fps:60
[ 0.678420] rk3288-lcdc lcdc0: wakeup from standby!
[ 0.723875] alloc_buffer:ion_phy_addr=0x10000000
[ 0.736600] fb0:phy:10000000>>vir:f0191000>>len:0x1800000
[ 0.773688] rk3288-lcdc lcdc0: lcdc0 probe ok, iommu enabled
[ 0.774178] rockchip_set_mux:warning ignore bank num 15
[ 0.774318] rockchip_set_mux:warning ignore bank num 15
[ 0.774433] rockchip_set_mux:warning ignore bank num 15
[ 0.774561] rockchip_set_mux:warning ignore bank num 15
[ 0.774671] rockchip_set_mux:warning ignore bank num 15
[ 0.774784] rockchip_set_mux:warning ignore bank num 15
[ 0.775394] rockchip_set_mux:warning ignore bank num 15
[ 0.775567] rockchip_set_mux:warning ignore bank num 15
[ 0.776123] rockchip_set_mux:warning ignore bank num 15
[ 0.776269] rockchip_set_mux:warning ignore bank num 15
[ 0.776813] rockchip_set_mux:warning ignore bank num 15
[ 0.776956] rockchip_set_mux:warning ignore bank num 15
[ 0.777518] rockchip_set_mux:warning ignore bank num 15
[ 0.777672] rockchip_set_mux:warning ignore bank num 15
[ 0.779156] NET: Registered protocol family 2
[ 0.779655] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.779793] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.779930] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.779989] TCP: reno registered
[ 0.780006] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.780043] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.780256] NET: Registered protocol family 1
[ 0.780450] Unpacking initramfs...
[ 0.843202] Freeing initrd memory: 1152K (c59fc000 - c5b1c000)
[ 0.843821] hw perfevents: enabled with ARMv7 Cortex-A12 PMU driver, 7 counters available
[ 0.844319] probe device ff9a0000.vpu_service
[ 0.844537] vpu_service: power on
[ 0.845607] checking hw id 4831
[ 0.846061] vpu_service set to auto frequency mode
[ 0.846125] vcodec vpu_service: vcodec ion client create success!
[ 0.846595] rk_iommu ff9a0800.vpu_mmu: (vpu) Enabled
[ 0.846626] rk_iommu ff9a0800.vpu_mmu: (vpu) Disabled
[ 0.846642] rk_iommu ff9a0800.vpu_mmu: rockchip_iommu_detach_device: Detached IOMMU with pgtable 0x2e26e000
[ 0.846656] vpu_service: power off...
[ 0.846696] done
[ 0.846706] init success
[ 0.846770] probe device ff9c0000.hevc_service
[ 0.846956] hevc_service: power on
[ 0.848019] checking hw id 6867
[ 0.848298] vcodec hevc_service: vcodec ion client create success!
[ 0.848580] rk_iommu ff9c0440.hevc_mmu: (hevc) Enabled
[ 0.848610] rk_iommu ff9c0440.hevc_mmu: (hevc) Disabled
[ 0.848625] rk_iommu ff9c0440.hevc_mmu: rockchip_iommu_detach_device: Detached IOMMU with pgtable 0x2e26c000
[ 0.848638] hevc_service: power off...
[ 0.848676] done
[ 0.848686] init success
[ 0.848799] rknandbase v1.0 2014-03-31
[ 0.849000] rknand_probe clk rate = 148500000
[ 0.849110] rknand_driver:ret = 0
[ 0.849493] audit: initializing netlink socket (disabled)
[ 0.849541] type=2000 audit(0.400:1): initialized
[ 0.850386] bounce pool size: 64 pages
[ 0.854833] fuse init (API version 7.22)
[ 0.855235] msgmni has been set to 1456
[ 0.857206] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 0.857225] io scheduler noop registered
[ 0.857237] io scheduler deadline registered
[ 0.857329] io scheduler cfq registered (default)
[ 0.858175] rga ff920000.rga: rga ion client create success!
[ 0.858330] rga: Driver loaded succesfully
[ 0.858777] IEP Power ON
[ 0.858816] iep ion client create success!
[ 0.859186] rk_iommu ff900800.iep_mmu: (iep) Enabled
[ 0.859213] IEP Power OFF
[ 0.859227] rk_iommu ff900800.iep_mmu: (iep) Disabled
[ 0.859243] rk_iommu ff900800.iep_mmu: rockchip_iommu_detach_device: Detached IOMMU with pgtable 0x2e261000
[ 0.859261] IEP Driver loaded succesfully
[ 0.859354] Module initialized.
[ 0.860139] dma-pl330 ffb20000.pdma: Loaded driver for PL330 DMAC-2364208
[ 0.860159] dma-pl330 ffb20000.pdma:DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10
[ 0.861389] dma-pl330 ff250000.pdma: Loaded driver for PL330 DMAC-2364208
[ 0.861410] dma-pl330 ff250000.pdma:DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[ 0.861675] pwm-voltage-regulator pwm_regulator.23: unable to request PWM, trying legacy API
[ 0.861694] pwm-voltage-regulator pwm_regulator.23: unable to request legacy PWM
[ 0.861707] pwm_regulator_probe:error
[ 0.861730] platform pwm_regulator.23: Driver pwm-voltage-regulator requests probe deferral
[ 0.862086] rk_serial.c v1.8 2014-03-04
[ 0.862302] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 87) is a rk29_serial.0
[ 0.862491] serial ff180000.serial: membase 0xf015e000
[ 0.865248] loop: module loaded
[ 0.865857] SCSI Media Changer driver v0.25
[ 0.866165] tun: Universal TUN/TAP device driver, 1.6
[ 0.866179] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.866707] stmmac_probe_config_dt: Can not read property: pmu_regulator.
[ 0.866725] stmmac_probe_config_dt: Can not read property: pmu_enable_level.
[ 0.866739] stmmac_probe_config_dt: clock input or output? (input).
[ 0.866752] stmmac_probe_config_dt: TX delay(0x30).
[ 0.866764] stmmac_probe_config_dt: RX delay(0x10).
[ 0.866802] stmmac_probe_config_dt: is rockchip,rk3288-gmac
[ 0.866813] stmmc_pltfr_init:
[ 0.866823] stmmc_pltfr_init: ERROR: Get power-gpio failed.
[ 0.866846] stmmc_pltfr_init: ERROR: Request gmac phy reset pin failed.
[ 0.866857] stmmc_pltfr_init: init for RGMII
[ 0.866869] tx delay=0x30
[ 0.866869] rx delay=0x10
[ 0.867306] stmmac - user ID: 0x10, Synopsys ID: 0x35
[ 0.867319]Normal descriptors
[ 0.867329]Ring mode enabled
[ 0.867339]DMA HW capability register supported
[ 0.867351]RX Checksum Offload Engine supported (type 2)
[ 0.867362]TX Checksum insertion supported
[ 0.867371]Wake-Up On Lan supported
[ 0.867407]Enable RX Mitigation via HW Watchdog Timer
[ 0.867826] PPP generic driver version 2.4.2
[ 0.867971] PPP BSD Compression module registered
[ 0.867985] PPP Deflate Compression module registered
[ 0.868008] PPP MPPE Compression module registered
[ 0.868021] NET: Registered protocol family 24
[ 0.868057] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[ 0.868071] CSLIP: code copyright 1989 Regents of the University of California.
[ 0.868085] Rockchip WiFi SYS interface (V1.00) ...
[ 0.868182] usbcore: registered new interface driver catc
[ 0.868220] usbcore: registered new interface driver kaweth
[ 0.868234] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[ 0.868276] usbcore: registered new interface driver pegasus
[ 0.868313] usbcore: registered new interface driver rtl8150
[ 0.868348] usbcore: registered new interface driver r8152
[ 0.868360] hso: drivers/net/usb/hso.c: Option Wireless
[ 0.868427] usbcore: registered new interface driver hso
[ 0.868478] usbcore: registered new interface driver asix
[ 0.868515] usbcore: registered new interface driver ax88179_178a
[ 0.868552] usbcore: registered new interface driver cdc_ether
[ 0.868587] usbcore: registered new interface driver cdc_eem
[ 0.868621] usbcore: registered new interface driver dm9601
[ 0.868656] usbcore: registered new interface driver dm9620
[ 0.868713] usbcore: registered new interface driver smsc75xx
[ 0.868759] usbcore: registered new interface driver smsc95xx
[ 0.868795] usbcore: registered new interface driver gl620a
[ 0.868831] usbcore: registered new interface driver net1080
[ 0.868867] usbcore: registered new interface driver plusb
[ 0.868904] usbcore: registered new interface driver rndis_host
[ 0.868939] usbcore: registered new interface driver cdc_subset
[ 0.868979] usbcore: registered new interface driver zaurus
[ 0.869018] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[ 0.869079] usbcore: registered new interface driver int51x1
[ 0.869116] usbcore: registered new interface driver kalmia
[ 0.869152] usbcore: registered new interface driver ipheth
[ 0.869193] usbcore: registered new interface driver sierra_net
[ 0.869229] usbcore: registered new interface driver cx82310_eth
[ 0.869281] usbcore: registered new interface driver cdc_ncm
[ 0.869319] usbcore: registered new interface driver qmi_wwan
[ 0.869356] usbcore: registered new interface driver cdc_mbim
[ 0.869369] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.871752] ehci_rk_probe f1a00000 f1a00010
[ 0.871769] rockchip_ehci_host ff500000.usb: Rockchip On-Chip EHCI Host Controller
[ 0.871807] rockchip_ehci_host ff500000.usb: new USB bus registered, assigned bus number 1
[ 0.872211] rockchip_ehci_host ff500000.usb: irq 56, io mem 0xff500000
[ 0.889660] rockchip_ehci_host ff500000.usb: USB 0.0 started, EHCI 1.00
[ 0.889744] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.889762] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.889777] usb usb1: Product: Rockchip On-Chip EHCI Host Controller
[ 0.889792] usb usb1: Manufacturer: Linux 3.10.0 ehci_hcd
[ 0.889805] usb usb1: SerialNumber: ff500000.usb
[ 0.890276] hub 1-0:1.0: USB hub found
[ 0.890301] hub 1-0:1.0: 1 port detected
[ 0.919170] ehci_rk_probe ok
[ 0.919325] usbcore: registered new interface driver cdc_acm
[ 0.919339] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 0.919394] usbcore: registered new interface driver usblp
[ 0.919437] usbcore: registered new interface driver cdc_wdm
[ 0.919505] usbcore: registered new interface driver usb-storage
[ 0.919544] usbcore: registered new interface driver ums-alauda
[ 0.919581] usbcore: registered new interface driver ums-cypress
[ 0.919617] usbcore: registered new interface driver ums-datafab
[ 0.919653] usbcore: registered new interface driver ums_eneub6250
[ 0.919689] usbcore: registered new interface driver ums-freecom
[ 0.919725] usbcore: registered new interface driver ums-isd200
[ 0.919761] usbcore: registered new interface driver ums-jumpshot
[ 0.919796] usbcore: registered new interface driver ums-karma
[ 0.919832] usbcore: registered new interface driver ums-onetouch
[ 0.919873] usbcore: registered new interface driver ums-sddr09
[ 0.919914] usbcore: registered new interface driver ums-sddr55
[ 0.919952] usbcore: registered new interface driver ums-usbat
[ 0.920040] usbcore: registered new interface driver usbserial
[ 0.920081] usbcore: registered new interface driver usbserial_generic
[ 0.920114] usbserial: USB Serial support registered for generic
[ 0.920152] usbcore: registered new interface driver option
[ 0.920183] usbserial: USB Serial support registered for GSM modem (1-port)
[ 0.920261] usbcore: registered new interface driver trancevibrator
[ 0.920274] usb20_otg: version 3.10a 21-DEC-2012
[ 0.920668] f1a80040
[ 0.920681] Core Release: 3.10a
[ 0.920693] Setting default values for core params
[ 0.920842] Using Buffer DMA mode
[ 0.920855] Periodic Transfer Interrupt Enhancement - disabled
[ 0.920867] Multiprocessor Interrupt Enhancement - disabled
[ 0.920879] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 0.920890] ^^^^^^^^^^^^^^^^^Device Mode
[ 0.920904] Dedicated Tx FIFOs mode
[ 0.920923] pcd_init otg_dev = ed9c1300
[ 0.921067] usb20_otg ff580000.usb: DWC OTG Controller
[ 0.921103] usb20_otg ff580000.usb: new USB bus registered, assigned bus number 2
[ 0.921135] usb20_otg ff580000.usb: irq 55, io mem 0x00000000
[ 0.921200] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.921218] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.921233] usb usb2: Product: DWC OTG Controller
[ 0.921246] usb usb2: Manufacturer: Linux 3.10.0 dwc_otg_hcd
[ 0.921259] usb usb2: SerialNumber: ff580000.usb
[ 0.921663] hub 2-0:1.0: USB hub found
[ 0.921686] hub 2-0:1.0: 1 port detected
[ 0.921968] usb20_host: version 3.10a 21-DEC-2012
[ 0.924403] f1b00040
[ 0.924416] Core Release: 3.10a
[ 0.924427] Setting default values for core params
[ 0.924553] Using Buffer DMA mode
[ 0.924565] Periodic Transfer Interrupt Enhancement - disabled
[ 0.924576] Multiprocessor Interrupt Enhancement - disabled
[ 0.924588] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 0.924598] ^^^^^^^^^^^^^^^^^^Host Mode
[ 0.924623] usb20_host ff540000.usb: DWC OTG Controller
[ 0.924649] usb20_host ff540000.usb: new USB bus registered, assigned bus number 3
[ 0.924684] usb20_host ff540000.usb: irq 57, io mem 0x00000000
[ 0.924776] Init: Power Port (0)
[ 0.924833] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.924850] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.924865] usb usb3: Product: DWC OTG Controller
[ 0.924878] usb usb3: Manufacturer: Linux 3.10.0 dwc_otg_hcd
[ 0.924891] usb usb3: SerialNumber: ff540000.usb
[ 0.925275] hub 3-0:1.0: USB hub found
[ 0.925302] hub 3-0:1.0: 1 port detected
[ 0.925845] .. rk pwm remotectl v1.0 init
[ 0.925941] remotectl probe j=0x0
[ 0.926099] input: ff680000.pwm as /devices/ff680000.pwm/input/input0
[ 0.926294] pwm enable val=0x646205
[ 0.926568] usbcore: registered new interface driver xpad
[ 0.926621] usbcore: registered new interface driver usb_acecad
[ 0.926664] usbcore: registered new interface driver aiptek
[ 0.926705] usbcore: registered new interface driver gtco
[ 0.926747] usbcore: registered new interface driver hanwang
[ 0.926787] usbcore: registered new interface driver kbtab
[ 0.926839] usbcore: registered new interface driver wacom
[ 0.927173] sensor_register_slave:mma8452,id=17
[ 0.927188] sensor_register_slave:cm3217,id=44
[ 0.927200] sensor_register_slave:cm3218,id=45
[ 0.931889] rtc_hym8563 0-0051: rtc core: registered hym8563 as rtc0
[ 0.931942] i2c /dev entries driver
[ 0.932606] IR NEC protocol handler initialized
[ 0.932619] IR RC5(x) protocol handler initialized
[ 0.932631] IR RC6 protocol handler initialized
[ 0.932642] IR JVC protocol handler initialized
[ 0.932652] IR Sony protocol handler initialized
[ 0.932662] IR RC5 (streamzap) protocol handler initialized
[ 0.932673] IR SANYO protocol handler initialized
[ 0.932683] IR MCE Keyboard/mouse protocol handler initialized
[ 0.932768] usbcore: registered new interface driver uvcvideo
[ 0.932781] USB Video Class driver (1.1.1)
[ 0.933533] rockchip_temp_probe,line=362
[ 0.933854] tsadc ff280000.tsadc: initialized
[ 0.934222] device-mapper: uevent: version 1.0.3
[ 0.934466] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[ 0.934756] Bluetooth: HCI UART driver ver 2.2
[ 0.934772] Bluetooth: HCI H4 protocol initialized
[ 0.934784] Bluetooth: HCILL protocol initialized
[ 0.940003] cpufreq version 1.0, suspend freq 816 MHz
[ 0.940197] cpuidle: using governor ladder
[ 0.940210] cpuidle: using governor menu
[ 0.940248] Synopsys Designware Multimedia Card Interface Driver
[ 0.940493] dwmmc_rockchip ff0f0000.rksdmmc: Version ID is 270a
[ 0.940780] dwmmc_rockchip ff0f0000.rksdmmc: Using internal DMA controller.
[ 0.940943] 3230..dw_mci_init_slot: fmin=400000, fmax=100000000
[ 0.940960] Line3235..dw_mci_init_slot: The rk_sdmmc Ver 1.12 2014-07-08
[ 0.941096] 1357..dw_mci_set_ios:no card.
[ 0.958541] 1357..dw_mci_set_ios:no card.
[ 0.978251] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out 800000Hz for init
[ 0.978294] dwmmc_rockchip ff0f0000.rksdmmc: DW MMC controller at irq 67, 32 bit host data width, 256 deep fifo
[ 0.978314] dwmmc_rockchip ff0f0000.rksdmmc: 1 slots initialized
[ 0.978604] dwmmc_rockchip ff0c0000.rksdmmc: Version ID is 270a
[ 0.979401] dwmmc_rockchip ff0c0000.rksdmmc: Using internal DMA controller.
[ 0.979568] 3224..dw_mci_init_slot: fmin=300000, fmax=50000000
[ 0.980046] 1357..dw_mci_set_ios:no card.
[ 0.997897] 1357..dw_mci_set_ios:no card.
[ 1.010365] mmc0: BKOPS_EN bit is not set
[ 1.012252] rk_sdmmc: BOOT Bus speed=0Hz,Bus width=8bits.
[ 1.014541] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0)
[ 1.014565] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out normal clock
[ 1.017712] dwmmc_rockchip ff0c0000.rksdmmc: DW MMC controller at irq 64, 32 bit host data width, 256 deep fifo
[ 1.017726] dwmmc_rockchip ff0c0000.rksdmmc: 1 slots initialized
[ 1.017993] dwmmc_rockchip ff0d0000.rksdmmc: Version ID is 270a
[ 1.018163] dwmmc_rockchip ff0d0000.rksdmmc: Using internal DMA controller.
[ 1.018275] 3230..dw_mci_init_slot: fmin=200000, fmax=50000000
[ 1.018355] 1357..dw_mci_set_ios:no card.
[ 1.029569] rk_sdmmc: BOOT
[ 1.029569]execute tuning: candidates_degree = SDMMC_SHIFT_DEGREE_0SDMMC_SHIFT_DEGREE_90SDMMC_SHIFT_DEGREE_180SDMMC_SHIFT_DEGREE_INVALID
[ 1.029670] mmc0: new HS200 MMC card at address 0001
[ 1.029931] mmcblk0: mmc0:0001 AWMB3R 14.5 GiB
[ 1.030237] uboot: 0x000400000 -- 0x000800000 (4 MB)
[ 1.030250] misc: 0x000800000 -- 0x000c00000 (4 MB)
[ 1.030259] resource: 0x000c00000 -- 0x001c00000 (16 MB)
[ 1.030269] kernel: 0x001c00000 -- 0x002c00000 (16 MB)
[ 1.030277] boot: 0x002c00000 -- 0x004c00000 (32 MB)
[ 1.030286] recovery: 0x004c00000 -- 0x006c00000 (32 MB)
[ 1.030295] backup: 0x006c00000 -- 0x00a000000 (52 MB)
[ 1.030303] cache: 0x00a000000 -- 0x012000000 (128 MB)
[ 1.030312] kpanic: 0x012000000 -- 0x012400000 (4 MB)
[ 1.030320] system: 0x012400000 -- 0x042400000 (768 MB)
[ 1.030329] metadata: 0x042400000 -- 0x042800000 (4 MB)
[ 1.030337] userdata: 0x042800000 -- 0x082800000 (1024 MB)
[ 1.030346] radical_update: 0x082800000 -- 0x086800000 (64 MB)
[ 1.030355] user: 0x086800000 -- 0x3a3a00000 (12754 MB)
[ 1.030380]mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p141357..dw_mci_set_ios:no card.
[ 1.037258] 1357..dw_mci_set_ios:no card.
[ 1.056934] 1357..dw_mci_set_ios:no card.
[ 1.057140] dwmmc_rockchip ff0d0000.rksdmmc: DW MMC controller at irq 65, 32 bit host data width, 256 deep fifo
[ 1.057154] dwmmc_rockchip ff0d0000.rksdmmc: 1 slots initialized
[ 1.057408] leds-gpio leds.31: pins are not configured from the driver
[ 1.057637] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.058926] usbcore: registered new interface driver usbhid
[ 1.058937] usbhid: USB HID core driver
[ 1.059236] ashmem: initialized
[ 1.059335] logger: created 256K log 'log_main'
[ 1.059428] logger: created 256K log 'log_events'
[ 1.059521] logger: created 256K log 'log_radio'
[ 1.059613] logger: created 256K log 'log_system'
[ 1.060591] input: rk29-keypad as /devices/ff100000.adc/key.34/input/input1
[ 1.061178] rockchip-pinctrl ff770000.pinctrl: pin gpio6-8 already requested by ; cannot claim for 2-0010
[ 1.061194] rockchip-pinctrl ff770000.pinctrl: pin-200 (2-0010) status -22
[ 1.061205] rockchip-pinctrl ff770000.pinctrl: could not request pin 200 on device rockchip-pinctrl
[ 1.061216] ES8323 2-0010: Error applying setting, reverse things back
[ 1.061501] es8323 probe i2c recv ok
[ 1.061709] i2c-core: driver using legacy suspend method
[ 1.061718] i2c-core: driver using legacy resume method
[ 1.062022] rockchip-hdmi-spdif rockchip-hdmi-spdif.27: ASoC: CPU DAI (null) not registered
[ 1.062052] rockchip_hdmi_spdif_audio_probe() register card failed:-517
[ 1.062071] platform rockchip-hdmi-spdif.27: Driver rockchip-hdmi-spdif requests probe deferral
[ 1.062311] es8323_probe
[ 1.062407] es8323_probe:register ISR (irq=194)
[ 1.696891] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> NULL --> Left Line Mux
[ 1.696903] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> NULL -> Left Line Mux
[ 1.696914] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> NULL --> Left Line Mux
[ 1.696923] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> NULL -> Left Line Mux
[ 1.696932] ES8323 2-0010: ASoC: no dapm match for Left PGA Mux --> NULL --> Left Line Mux
[ 1.696940] ES8323 2-0010: ASoC: Failed to add route Left PGA Mux -> NULL -> Left Line Mux
[ 1.696950] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> NULL --> Right Line Mux
[ 1.696958] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> NULL -> Right Line Mux
[ 1.696967] ES8323 2-0010: ASoC: no dapm match for RINellTrk3->8:UL$ --> Right Line Mux
[ 1.696975] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> NULL -> Right Line Mux
[ 1.696983] ES8323 2-0010: ASoC: no dapm match for Right PGA Mux --> NULL --> Right Line Mux
[ 1.696991] ES8323 2-0010: ASoC: Failed to add route Right PGA Mux -> NULL -> Right Line Mux
[ 1.697001] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> LAMP --> Left PGA Mux
[ 1.697008] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> LAMP -> Left PGA Mux
[ 1.697017] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> LAMP --> Left PGA Mux
[ 1.697025] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> LAMP -> Left PGA Mux
[ 1.697034] ES8323 2-0010: ASoC: no dapm match for Differential Mux --> LAMP --> Left PGA Mux
[ 1.697042] ES8323 2-0010: ASoC: Failed to add route Differential Mux -> LAMP -> Left PGA Mux
[ 1.697051] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> RAMP --> Right PGA Mux
[ 1.697059] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> RAMP -> Right PGA Mux
[ 1.697068] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> RAMP --> Right PGA Mux
[ 1.697075] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> RAMP -> Right PGA Mux
[ 1.697084] ES8323 2-0010: ASoC: no dapm match for Differential Mux --> RAMP --> Right PGA Mux
[ 1.697092] ES8323 2-0010: ASoC: Failed to add route Differential Mux -> RAMP -> Right PGA Mux
[ 1.697102] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> LAMP --> Differential Mux
[ 1.697109] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> LAMP -> Differential Mux
[ 1.697118] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> RAMP --> Differential Mux
[ 1.697126] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> RAMP -> Differential Mux
[ 1.697134] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> LAMP --> Differential Mux
[ 1.697142] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> LAMP -> Differential Mux
[ 1.697151] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> RAMP --> Differential Mux
[ 1.697158] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> RAMP -> Differential Mux
[ 1.697178] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> LAMP --> Left Line Mux
[ 1.697186] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> LAMP -> Left Line Mux
[ 1.697194] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> LAMP --> Left Line Mux
[ 1.697202] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> LAMP -> Left Line Mux
[ 1.697210] ES8323 2-0010: ASoC: no dapm match for Left PGA Mux --> LAMP --> Left Line Mux
[ 1.697218] ES8323 2-0010: ASoC: Failed to add route Left PGA Mux -> LAMP -> Left Line Mux
[ 1.697227] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> RAMP --> Right Line Mux
[ 1.697234] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> RAMP -> Right Line Mux
[ 1.697243] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> RAMP --> Right Line Mux
[ 1.697250] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> RAMP -> Right Line Mux
[ 1.697259] ES8323 2-0010: ASoC: no dapm match for Right PGA Mux --> RAMP --> Right Line Mux
[ 1.697267] ES8323 2-0010: ASoC: Failed to add route Right PGA Mux -> RAMP -> Right Line Mux
[ 1.697405] ES8323 2-0010: ASoC: mux Right Line Mux has no paths
[ 1.697416] ES8323 2-0010: ASoC: mux Left Line Mux has no paths
[ 1.697426] ES8323 2-0010: ASoC: mux Right PGA Mux has no paths
[ 1.697436] ES8323 2-0010: ASoC: mux Left PGA Mux has no paths
[ 1.697461] ES8323 2-0010: ASoC: mux Differential Mux has no paths
[ 1.700014] Enter::rk29_es8323_init----123
[ 1.703307] rockchip-es8323 rockchip-es8323.29:ES8323 HiFi <-> rockchip-i2s.0 mapping ok
[ 1.705406] u32 classifier
[ 1.705413] Actions configured
[ 1.705425] Netfilter messages via NETLINK v0.30.
[ 1.705488] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 1.705765] ctnetlink v0.93: registering with nfnetlink.
[ 1.705822] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 1.705830] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 1.706059] xt_time: kernel timezone is -0000
[ 1.706225] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.706333] arp_tables: (C) 2002 David S. Miller
[ 1.706389] TCP: cubic registered
[ 1.706396] Initializing XFRM netlink socket
[ 1.706584] NET: Registered protocol family 10
[ 1.707017] mip6: Mobile IPv6
[ 1.707044] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 1.707150] sit: IPv6 over IPv4 tunneling driver
[ 1.707443] NET: Registered protocol family 17
[ 1.707465] NET: Registered protocol family 15
[ 1.707508] Bridge firewalling registered
[ 1.707519] Ebtables v2.0 registered
[ 1.707666] Bluetooth: RFCOMM TTY layer initialized
[ 1.707689] Bluetooth: RFCOMM socket layer initialized
[ 1.707695] Bluetooth: RFCOMM ver 1.11
[ 1.707702] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 1.707708] Bluetooth: BNEP filters: protocol multicast
[ 1.707718] Bluetooth: BNEP socket layer initialized
[ 1.707725] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 1.707734] Bluetooth: HIDP socket layer initialized
[ 1.707757] l2tp_core: L2TP core driver, V2.0
[ 1.707769] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 1.707776] : Enter rfkill_wlan_init
[ 1.707955] : Enter rfkill_wlan_probe
[ 1.707964] wlan_platdata_parse_dt: wifi_chip_type = bcmwifi
[ 1.707972] : wlan_platdata_parse_dt: enable wifi power control.
[ 1.707981] : wlan_platdata_parse_dt: disable wifi io reference voltage control.
[ 1.707989] : wlan_platdata_parse_dt: wifi power controled by gpio.
[ 1.708008] : wlan_platdata_parse_dt: get property: WIFI,poweren_gpio = 156, flags = 0.
[ 1.708028] : wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 158, flags = 0.
[ 1.708035] : rfkill_wlan_probe: init gpio
[ 1.708061] : rockchip_wifi_voltage_select: wifi & sdio reference voltage: 1.8V
[ 1.708099] : Exit rfkill_wlan_probe
[ 1.708141] : Enter rfkill_rk_init
[ 1.708256] : bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 147.
[ 1.708271] : bluetooth_platdata_parse_dt: get property: BT,power_gpio = 155.
[ 1.708283] : bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 157.
[ 1.708296] : bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 154.
[ 1.708308] : bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 159.
[ 1.708350] : Request irq for bt wakeup host
[ 1.708441] : ** disable irq
[ 1.708511] : ap6335 device registered.
[ 1.709070] rk3288-hdmi ff980000.hdmi: rk3288 hdmi probe sucess.
[ 1.709385] VFP support v0.3: implementor 41 architecture 3 part 30 variant d rev 0
[ 1.709403] rk3288_init_suspend
[ 1.709411] rk3288_suspend_init enter
[ 1.709535] rk3288_suspend_init: pm_ctrbits =40017
[ 1.709564] gpio_get_dts_info suspend:8
[ 1.709571] gpio_get_dts_info resume:8
[ 1.709576] rockchip,pmic-suspend_gpios:1007c30 1007c40 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
[ 1.709601] rockchip,pmic-resume_gpios:2007c32 2007c42 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
[ 1.709725] clks_gating_suspend_init:clkgt info ok
[ 1.709804] Registering SWP/SWPB emulation handler
[ 1.710104] ddrfreq: verion 1.2 20140526
[ 1.710117] ddrfreq: normal 456MHz video_1080p 0MHz video_4k 456MHz dualview 0MHz idle 0MHz suspend 200MHz reboot 456MHz
[ 1.710124] ddrfreq: auto-freq=0
[ 1.710130] ddrfreq: auto-freq-table 240MHz
[ 1.710135] ddrfreq: auto-freq-table 324MHz
[ 1.710141] ddrfreq: auto-freq-table 456MHz
[ 1.710146] ddrfreq: auto-freq-table 528MHz
[ 1.711802] act_ldo3: operation not allowed
[ 1.712039] vga_edid_probe: turn on ldo3 done.
[ 1.712074] act_ldo4: operation not allowed
[ 1.712307] vga_edid_probe: turn on ldo done.
[ 1.712330] act_ldo2: operation not allowed
[ 1.712560] vga_edid_probe: turn on ldo2 done.
[ 1.712581] act_ldo8: operation not allowed
[ 1.712809] vga_edid_probe: turn on ldo done.
[ 1.715380] unable to read EDID block.
[ 1.715390] vga-ddc: read and parse edid failed errno:-5.
[ 1.715396] vga_edid_probe: success. 10
[ 1.715497] firefly_vga_get_enable 180, 0
[ 1.715505] firefly_vga_get_status 186
[ 1.715518] firefly_vga_set_enable 159 enable:1
[ 1.715534] firefly_vga_enable 130 start
[ 1.715540] firefly_switch_fb 55
[ 1.715547]
[ 1.715547] rk_fb_switch_screen lcdc_id 0 type 1 enable 1
[ 1.715558] fb0 win id 1 state 1
[ 1.715568] regulator-dummy: disabling
[ 1.715574] rk3288-lcdc lcdc0: lcdc0: dclk:148500000>>fps:60
[ 1.715591] fb1 win id 0 state 0
[ 1.715597] fb2 win id 2 state 0
[ 1.715603] fb3 win id 3 state 0
[ 1.715608] fb4 win id 4 state 0
[ 1.715613]
[ 1.715613] rk_fb_switch_screen lcdc_id 0 type 1 enable 1 done
[ 1.715613]
[ 1.715637] VGA ENABLE
[ 1.715818] rockchip-hdmi-spdif rockchip-hdmi-spdif.27: ASoC: CPU DAI (null) not registered
[ 1.715842] rockchip_hdmi_spdif_audio_probe() register card failed:-517
[ 1.715856] platform rockchip-hdmi-spdif.27: Driver rockchip-hdmi-spdif requests probe deferral
[ 1.715932] pcd_pullup, is_on 0
[ 1.715969] file system registered
[ 1.716499] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 1.716508] android_usb gadget: Number of LUNs=2
[ 1.716515]lun0: LUN: removable file: (no medium)
[ 1.716521]lun1: LUN: removable file: (no medium)
[ 1.716634] android_usb gadget: android_usb ready
[ 1.716706] sensor_init: Probe name sensors
[ 1.716720] sensor-dev.c v1.4 add angle calculation support between two gsensors 2013-09-01
[ 1.717245] rtc_hym8563 0-0051: setting system clock to 2011-01-01 12:01:31 UTC (1293883291)
[ 1.722601] usbcore: registered new interface driver snd-usb-audio
[ 1.722617] ALSA device list:
[ 1.722622] #0: RK_ES8323
[ 1.723897] Freeing unused kernel memory: 2360K (c0a6f000 - c0cbd000)
[ 1.724283] rockchip-hdmi-spdif rockchip-hdmi-spdif.27:rk-hdmi-spdif-hifi <-> rockchip-spdif mapping ok
[ 1.728430] SELinux:Permission attach_queue in class tun_socket not defined in policy.
[ 1.728442] SELinux: the above unknown classes and permissions will be denied
[ 2.004542] type=1403 audit(1293883291.780:2): policy loaded auid=4294967295 ses=4294967295
[ 2.004640] SELinux: Loaded policy from /sepolicy
[ 2.006072] type=1404 audit(1293883291.780:3): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
[ 2.897004] dwc_otg_hcd_enable, enable host controller
[ 2.948782] init: init.rk30board.bootmode.emmc.rc: 8: invalid command '/devices/ff0f0000.rksdmmc/mmc_host/mmc'
[ 2.948799] init: init.rk30board.bootmode.emmc.rc: 9: invalid command '/devices/ff0c0000.rksdmmc/mmc_host/mmc'
[ 2.948811] init: init.rk30board.bootmode.emmc.rc: 10: invalid command '/devices/ff580000.usb'
[ 2.948822] init: init.rk30board.bootmode.emmc.rc: 11: invalid command '/devices/ff580000.usb'
[ 2.948832] init: init.rk30board.bootmode.emmc.rc: 12: invalid command '/devices/ff500000.usb'
[ 2.948842] init: init.rk30board.bootmode.emmc.rc: 13: invalid command '/devices/ff500000.usb'
[ 2.948852] init: init.rk30board.bootmode.emmc.rc: 14: invalid command '/devices/ff540000.usb'
[ 2.948862] init: init.rk30board.bootmode.emmc.rc: 15: invalid command '/devices/ff540000.usb'
[ 2.949137] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
[ 2.999521] init: /dev/hw_random not found
[ 2.999578] keychord: using input dev ff680000.pwm for fevent
[ 2.999587] keychord: using input dev rk29-keypad for fevent
[ 3.000370] Using Buffer DMA mode
[ 3.000378] Periodic Transfer Interrupt Enhancement - disabled
[ 3.000384] Multiprocessor Interrupt Enhancement - disabled
[ 3.000391] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 3.000396] ^^^^^^^^^^^^^^^^^^Host Mode
[ 3.004494] fs_mgr: parse_link_device : path = NULL
[ 3.004519] fs_mgr: parse_link_device : path = NULL
[ 3.004545] fs_mgr: parse_link_device : path = NULL
[ 3.004562] fs_mgr: parse_link_device : path = NULL
[ 3.004578] fs_mgr: parse_link_device : path = NULL
[ 3.004597] fs_mgr: parse_link_device : path = NULL
[ 3.004613] fs_mgr: parse_link_device : path = NULL
[ 3.004628] fs_mgr: parse_link_device : path = NULL
[ 3.004685] fs_mgr: ---------------resize_fs blk_dev /dev/block/platform/ff0f0000.rksdmmc/by-name/system, type ext4fs_mgr: Running /sbin/resize2fs on /dev/block/platform/ff0f0000.rksdmmc/by-name/system
[ 3.005821] resize2fs: resize2fs 1.41.14 (22-Dec-2010)resize2fs: The filesystem is already 196608 blocks long.Nothing to do!resize2fs:
[ 3.011489] EXT4-fs (mmcblk0p10): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
[ 3.017698] EXT4-fs (mmcblk0p8): recovery complete
[ 3.018184] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard
[ 3.020056] EXT4-fs (mmcblk0p11): recovery complete
[ 3.020067] EXT4-fs (mmcblk0p11): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard
[ 3.037165] EXT4-fs (mmcblk0p12): recovery complete
[ 3.037656] EXT4-fs (mmcblk0p12): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard
[ 3.042842] drmboot: version magic '3.0.36+ SMP preempt mod_unload ARMv7 ' should be '3.10.0 SMP preempt mod_unload ARMv7 p2v8 '
[ 3.044674] Init: Power Port (0)
[ 3.047958] mali pd enabled
[ 3.047972] clk enabled
[ 3.047982] MALI_DVFS_STEP=4,div_dvfs=10
[ 3.047988] mali_dvfs_infotbl.clock=198000,min_threshold=0,max_threshold=70
[ 3.047996] mali_dvfs_infotbl.clock=297000,min_threshold=70,max_threshold=80
[ 3.048002] mali_dvfs_infotbl.clock=313000,min_threshold=86,max_threshold=90
[ 3.048010] mali_dvfs_infotbl.clock=480000,min_threshold=88,max_threshold=100
[ 3.048103] turn on mali power
[ 3.048123] mali ffa30000.gpu: GPU identified as 0x0750 r0p0 status 1
[ 3.048488] mali ffa30000.gpu: Probed as mali0
[ 3.050806] rk29_ipp: version magic '3.0.8+ SMP preempt mod_unload ARMv7 ' should be '3.10.0 SMP preempt mod_unload ARMv7 p2v8 '
[ 3.059172] init: /dev/hw_random not found
[ 3.064811] binder: 135:135 transaction failed 29189, size 0-0
[ 3.065321] init: cannot find '/system/vendor/bin/pvrsrvctl', disabling 'pvrsrvctl'
[ 3.067697] init: cannot find '/system/bin/rild3', disabling 'ril-daemon3'
[ 3.069270] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
[ 3.070166] init: cannot find '/system/bin/bindvbplayservice', disabling 'dvbdataserv'
[ 3.070510] init: cannot find '/system/bin/chrome.sh', disabling 'chrome'
[ 3.070862] init: cannot find '/system/bin/bplus_helper', disabling 'bplus_helper'
[ 3.072607] init: property 'ro.serialno' doesn't exist 从log看起来，Android部分的固件不完整，kernel部分应该没问题。
如果git下载断续，建议楼主下载压缩包进行编译。 谢谢阿sai的回答，
我开始是下载百度盘的压缩包，然后git pull一直无法下载更新，后来才用的git clone -b firefly/master git://git.us.linux-rockchip.org/rk3288_r-box_android4.4.2_sdk.git；
现在我从网站下载编译好的1111的img文件，烧到板子上也还是一样现象；
我在烧写*.img前有擦除flash过，不知道是不是这个有影响.
麻烦楼主将编译好的各个img文件大小列一下（特别是kernel.img和system.img的大小） 我编译的文件大小如下：
2014/11/2020:52 1,183,504 boot.img
2014/11/2020:52 6,241,532 kernel.img
2014/11/2020:52 49,152 misc.img
2014/11/2020:52 49,152 pcba_small_misc.img
2014/11/2020:52 49,152 pcba_whole_misc.img
2014/11/0717:57 4,257,551 ramdisk-recovery.img
2014/11/0717:57 1,177,399 ramdisk.img
2014/11/2020:52 10,534,912 recovery.img
2014/11/2020:52 117,248 resource.img
2014/11/2109:36 366,926 RK3288Loader_uboot_V2.17.02.bin
2014/11/2020:53 406,962,176 system.img leo 发表于 2014-11-21 09:47
我编译的文件大小如下：
2014/11/2020:52 1,183,504 boot.img
2014/11/2020:52 6,24 ...
楼主贴的img文件大小是合理的，原生态固件编译出来也和你的差不多。
搂主能够把adb logcat信息也发一下吗 leo 发表于 2014-11-21 09:47
我编译的文件大小如下：
2014/11/2020:52 1,183,504 boot.img
2014/11/2020:52 6,24 ...
文件大小也没什么异常，kernel可能偏小一点。楼主用最新的update.img也是一样的情况吗？如果用update能正常，就可以单独烧录kernel和system来排除是哪部分出现问题了 我直接烧官网的img文件Firefly-RK3288_Android4.4_201411111636.img都有是一样的。
你们哪位大牛编译的能跑起来的，上传一份给我试试，谢谢！ leo 发表于 2014-11-21 11:06
我直接烧官网的img文件Firefly-RK3288_Android4.4_201411111636.img都有是一样的。
你们哪位大牛编译的能 ...
http://pan.baidu.com/s/1nt8196x
下载这个压缩包试试，直接在下载镜像里点执行升级。我没有打包成update的 阿sai，非常感谢你的支持，我下了你的img文件到板子上，问题依旧啊。
另外，我在这之前执行过低格，不知道是不是这个有影响呢？
下载你的IMG文件后log如下：
DDR Version 1.00 20141007
In
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Memory OK
Memory OK
OUT
U-Boot 2014.10-RK3288-02 (Oct 30 2014 - 09:27:41)
CPU: rk3288
CPU's clock information:
arm pll = 600000000HZ
periph pll = 300000000HZ
ddr pll = 200000000HZ
codec pll = 594000000HZ
Board: Rockchip platform Board
DRAM:Found dram banks:1
Adding bank:0000000000000000(0000000080000000)
128 MiB
storage init OK!
Using default environment
GetParam
check parameter success
Unknow param: MACHINE_MODEL:rk30sdk!
Unknow param: MACHINE_ID:007!
Unknow param: MANUFACTURER:RK30SDK!
Unknow param: PWR_HLD: 0,0,A,0,1!
failed to prepare fdt from boot!
power key: bank-0 pin-5
can't find dts node for ricoh619
pmic:act8846
Can't find dts node for fuel guage cw201x
SecureBootEn = 0, SecureBootLock = 0
#Boot ver: 2014-10-30#2.17
sn:1006110001000029
no fuel gauge found
no fuel gauge found
read logo_on switch from dts
checkKey
vbus = 1
no fuel gauge found
Hit any key to stop autoboot:0
failed to load fdt from boot!
kernel @ 0x02000000 (0x005f3258)
ramdisk@ 0x059fc000 (0x0011f742)
Secure Boot state: 0
bootrk: do_bootm_linux...
Loading Device Tree to 0561c000, end 05636cc8 ... OK
Add bank:0000000000000000, 0000000080000000
Starting kernel ...
<hit enter to activate fiq debugger>
[ 0.000000] Booting Linux on physical CPU 0x500
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.10.0 (zjw@tchipserver2) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #20 SMP PREEMPT Thu Nov 13 21:16:26 CST 2014
[ 0.000000] CPU: ARMv7 Processor revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Rockchip RK3288 (Flattened Device Tree), model: rockchip,rk3288
[ 0.000000] rockchip_ion_reserve
[ 0.000000] cma: CMA: reserved 16 MiB at 2e800000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] PERCPU: Embedded 9 pages/cpu @c1eaa000 s14016 r8192 d14656 u36864
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.Total pages: 522768
[ 0.000000] Kernel command line: console=ttyFIQ0 androidboot.hardware=rk30board androidboot.console=ttyFIQ0 board.ap_has_alsa=0 init=/initmtdparts=rk29xxnand:0x00002000@0x00002000(uboot),0x00002000@0x00004000(misc),0x00008000@0x00006000(resource),0x00008000@0x0000e000(kernel),0x00010000@0x00016000(boot),0x00010000@0x00026000(recovery),0x0001a000@0x00036000(backup),0x00040000@0x00050000(cache),0x00002000@0x00090000(kpanic),0x00180000@0x00092000(system),0x00002000@0x00212000(metadata),0x00200000@0x00214000(userdata),0x00020000@0x00414000(radical_update),-@0x00434000(user) storagemedia=emmc loader.timestamp=2014-10-30_09:27:41 androidboot.serialno=1006110001000029
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 2048MB = 2048MB total
[ 0.000000] Memory: 2047140k/2047140k available, 50012k reserved, 1318912K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector: 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap: 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem: 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 (14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0a6ba18 (10639 kB)
[ 0.000000] .init : 0xc0a6c000 - 0xc0cba6c0 (2362 kB)
[ 0.000000] .data : 0xc0cbc000 - 0xc0d58458 ( 626 kB)
[ 0.000000] .bss : 0xc0d58458 - 0xc0e72e04 (1131 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] rk_clk_tree_init start! cru base = 0xfed00000
[ 0.000000] rk_get_uboot_display_flag: uboot_logo_on = 0
[ 0.000000] rkclk_init_clks: cnt_parent = 7
[ 0.000000] rkclk_init_clks: cnt_rate = 32
[ 0.000000] Architected local timer running at 24.00MHz (phys).
[ 0.000000] Switching to timer-based delay loop
[ 0.000000] sched_clock: ARM arch timer >56 bits at 24000kHz, resolution 41ns
[ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
[ 0.447020] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.447036] pid_max: default: 32768 minimum: 301
[ 0.447144] Security Framework initialized
[ 0.447160] SELinux:Initializing.
[ 0.447237] Mount-cache hash table entries: 512
[ 0.447870] Initializing cgroup subsys debug
[ 0.447884] Initializing cgroup subsys freezer
[ 0.447912] CPU: Testing write buffer coherency: ok
[ 0.448222] /cpus/cpu@0 missing clock-frequency property
[ 0.448236] /cpus/cpu@1 missing clock-frequency property
[ 0.448245] /cpus/cpu@2 missing clock-frequency property
[ 0.448254] /cpus/cpu@3 missing clock-frequency property
[ 0.448303] CPU0: thread -1, cpu 0, socket 5, mpidr 80000500
[ 0.448355] Setting up static identity map for 0xc0783668 - 0xc07836c0
[ 0.450783] last_log: 0x2e100000 map to 0xf0004000 and copy to 0xf0086000, size 0x80000 early 0x136f (version 3.0)
[ 0.525728] CPU1: Booted secondary processor
[ 0.525760] CPU1: thread -1, cpu 1, socket 5, mpidr 80000501
[ 0.545413] CPU2: Booted secondary processor
[ 0.545436] CPU2: thread -1, cpu 2, socket 5, mpidr 80000502
[ 0.565114] CPU3: Booted secondary processor
[ 0.565138] CPU3: thread -1, cpu 3, socket 5, mpidr 80000503
[ 0.565241] Brought up 4 CPUs
[ 0.565268] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[ 0.565278] CPU: All CPU(s) started in SVC mode.
[ 0.566011] devtmpfs: initialized
[ 0.571213] pinctrl core: initialized pinctrl subsystem
[ 0.571457] regulator-dummy: no parameters
[ 0.571966] NET: Registered protocol family 16
[ 0.573538] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.573792] ion_snapshot: 0x2e1a8000 map to 0xf0107000 and copy to 0xc0e4e454 (version 0.1)
[ 0.574087] Registered FIQ tty driver
[ 0.575245] console enabled
[ 0.575456] Registered fiq debugger ttyFIQ0
[ 0.575965] rockchip_get_bank_data:name=base start=0xff750000,end=0xff7500ff
[ 0.575989] rockchip_get_bank_data:name=mux_bank0 start=0xff730084,end=0xff73008f
[ 0.576009] rockchip_get_bank_data:name=pull_bank0 start=0xff730064,end=0xff73006f
[ 0.576035] rockchip_get_bank_data:name=drv_bank0 start=0xff730070,end=0xff73007b
[ 0.576132] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio1@ff780000 start=0xff780000,end=0xff7800ff
[ 0.576200] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio2@ff790000 start=0xff790000,end=0xff7900ff
[ 0.576263] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio3@ff7a0000 start=0xff7a0000,end=0xff7a00ff
[ 0.576326] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio4@ff7b0000 start=0xff7b0000,end=0xff7b00ff
[ 0.576389] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio5@ff7c0000 start=0xff7c0000,end=0xff7c00ff
[ 0.576452] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio6@ff7d0000 start=0xff7d0000,end=0xff7d00ff
[ 0.576516] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio7@ff7e0000 start=0xff7e0000,end=0xff7e00ff
[ 0.576580] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio8@ff7f0000 start=0xff7f0000,end=0xff7f00ff
[ 0.576649] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio15@ff7f2000 start=0xff7f2000,end=0xff7f20ff
[ 0.576716] rockchip_pinctrl_probe:name=RK3288-GPIO,type=3
[ 0.576731] rockchip_pinctrl_probe:name=base start=0xff770000,end=0xff77013f
[ 0.576747] rockchip_pinctrl_probe:name=pull start=0xff770140,end=0xff7701bf
[ 0.576761] rockchip_pinctrl_probe:name=drv start=0xff7701c0,end=0xff77023f
[ 0.577253] rockchip_interrupts_register:bank_num=7
[ 0.579111] rockchip_pinctrl_probe:init ok
[ 0.584759] rk_iommu ff900800.iep_mmu: (iep) Enter
[ 0.584880] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.584896] rk_iommu ff900800.iep_mmu: (iep) Initialized
[ 0.585061] rk_iommu ff950800.vip_mmu: (vip) Enter
[ 0.585167] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.585182] rk_iommu ff950800.vip_mmu: (vip) Initialized
[ 0.585347] rk_iommu ff930300.vopb_mmu: (vopb) Enter
[ 0.585453] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.585468] rk_iommu ff930300.vopb_mmu: (vopb) Initialized
[ 0.585624] rk_iommu ff940300.vopl_mmu: (vopl) Enter
[ 0.585729] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.585744] rk_iommu ff940300.vopl_mmu: (vopl) Initialized
[ 0.585915] rk_iommu ff9c0440.hevc_mmu: (hevc) Enter
[ 0.586038] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.586053] rk_iommu ff9c0440.hevc_mmu: (hevc) Initialized
[ 0.586210] rk_iommu ff9a0800.vpu_mmu: (vpu) Enter
[ 0.586316] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.586331] rk_iommu ff9a0800.vpu_mmu: (vpu) Initialized
[ 0.586500] rk_iommu ff914000.isp_mmu: (isp_mmu) Enter
[ 0.586622] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.586637] rk_iommu ff914000.isp_mmu: (isp_mmu) Initialized
[ 0.588183] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.588200] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.588404] DDR DEBUG: version 1.00 20140603
[ 0.588435] DDR DEBUG: Channel a:
[ 0.588445] DDR DEBUG: DDR3 Device
[ 0.588461] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Total Capability=1024MB
[ 0.588474] DDR DEBUG: Channel b:
[ 0.588482] DDR DEBUG: DDR3 Device
[ 0.588496] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Total Capability=1024MB
[ 0.588509] DDR DEBUG: addr=0xd5e000
[ 0.588519] DDR DEBUG: stride=9, size=256, halfcap=40000000
[ 0.588531] DDR DEBUG: socAddr=0xd5e000, socAddr=0xd5e100
[ 0.588543] DDR DEBUG: chAddr=0xd5e000, chAddr=0xd5e000
[ 0.588556] DDR DEBUG: dtar=0x601ab000, dtar=0x601ab000
[ 0.588798] DDR DEBUG: init success!!! freq=300MHz
[ 0.588808] DDR DEBUG: Channel a:
[ 0.588821] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
[ 0.588838] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
[ 0.588854] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
[ 0.588870] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=3,0, DGSL=1,1 extra clock, DGPS=360,360
[ 0.588885] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0
[ 0.588898] DDR DEBUG: DRV Pull-Up=0x19, DRV Pull-Dwn=0x19
[ 0.588909] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2
[ 0.588918] DDR DEBUG: Channel b:
[ 0.588931] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
[ 0.588947] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
[ 0.588963] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
[ 0.588979] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
[ 0.588993] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0
[ 0.589005] DDR DEBUG: DRV Pull-Up=0x19, DRV Pull-Dwn=0x19
[ 0.589016] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2
[ 0.609856] bio: create slab <bio-0> at 0
[ 0.610430] Enter firefly_noatx8_init
[ 0.610575] firefly_noatx8_probe 51
[ 0.610789] SCSI subsystem initialized
[ 0.610933] usbcore: registered new interface driver usbfs
[ 0.610976] usbcore: registered new interface driver hub
[ 0.611060] usbcore: registered new device driver usb
[ 0.611982] rockchip_i2c ff650000.i2c: i2c-0: Rockchip I2C adapter
[ 0.613293] rockchip_i2c ff140000.i2c: i2c-1: Rockchip I2C adapter
[ 0.613716] rockchip_i2c ff660000.i2c: i2c-2: Rockchip I2C adapter
[ 0.614141] rockchip_i2c ff150000.i2c: i2c-3: Rockchip I2C adapter
[ 0.614403] rockchip_i2c ff160000.i2c: i2c-4: Rockchip I2C adapter
[ 0.615237] media: Linux media interface: v0.10
[ 0.615279] Linux video capture interface: v2.00
[ 0.615324] pps_core: LinuxPPS API ver. 1 registered
[ 0.615336] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.615360] PTP clock support registered
[ 0.615477] Enter firefly_led_init
[ 0.615624] firefly_led_probe 290
[ 0.615744] rockchip_ion_parse_dt: num_heaps = 1
[ 0.615761] 0:03vmalloc0x(null)
[ 0.615993] Rockchip ion module is successfully loaded (v1.0)
[ 0.616146] Advanced Linux Sound Architecture Driver Initialized.
[ 0.616505] Bluetooth: Core ver 2.16
[ 0.616541] NET: Registered protocol family 31
[ 0.616554] Bluetooth: HCI device and connection manager initialized
[ 0.616571] Bluetooth: HCI socket layer initialized
[ 0.616586] Bluetooth: L2CAP socket layer initialized
[ 0.616614] Bluetooth: SCO socket layer initialized
[ 0.616832] cfg80211: Calling CRDA to update world regulatory domain
[ 0.617407] act8846_i2c_probe,line=898
[ 0.618367] act8846_parse_dt,line=746
[ 0.618790] act8846_i2c_probe: act8846_pmic_hold=1
[ 0.618811] act8846_i2c_probe: act8846_pmic_sleep=1
[ 0.618829] act8846_i2c_probe: act8846_pmic_cpu_det_gpio=1
[ 0.618846] act8846_i2c_probe: act8846_pmic_usb_hub_reset_gpio=1
[ 0.620642] act_dcdc1: 1200 mV
[ 0.623326] vccio: 3300 mV
[ 0.625155] vdd_logic: 700 <--> 1500 mV at 1100 mV
[ 0.627844] act_dcdc4: 2000 mV
[ 0.629068] vccio_sd: 1800 <--> 3300 mV at 3300 mV
[ 0.631117] act_ldo2: 1000 mV
[ 0.633169] act_ldo3: 1800 mV
[ 0.635222] act_ldo4: 3300 mV
[ 0.637268] act_ldo5: 3300 mV
[ 0.639314] act_ldo6: 1000 mV
[ 0.641375] vcc_18: 1800 mV
[ 0.643427] act_ldo8: 1800 mV
[ 0.648104] vdd_arm: 712 <--> 1500 mV at 1000 mV
[ 0.652731] vdd_gpu: 712 <--> 1500 mV at 1000 mV
[ 0.653150] rk808_i2c_probe,line=1368
[ 0.654461] The device is not rk808 -11
[ 0.654543] rk808: probe of 0-001b failed with error -11
[ 0.655277] Switching to clocksource arch_sys_counter
[ 0.674500] rk-fb rockchip-fb: rk fb ion client create success!
[ 0.674525] rk-fb rockchip-fb: rockchip framebuffer driver probe
[ 0.674926] rk-screen rk_screen.9: rockchip screen probe success
[ 0.675220] rk32-lvds rk32-lvds: rk32 lvds driver probe success
[ 0.675430] rk32-edp ff970000.edp: screen is not edp!
[ 0.675452] rk32-edp: probe of ff970000.edp failed with error -22
[ 0.675775] rk3288-lcdc lcdc0: can't find power_ctr node for lcdc0
[ 0.676031] graphics fb0: rockchip framebuffer registerd:fb0
[ 0.676389] graphics fb1: rockchip framebuffer registerd:fb1
[ 0.676567] graphics fb2: rockchip framebuffer registerd:fb2
[ 0.676720] graphics fb3: rockchip framebuffer registerd:fb3
[ 0.676868] graphics fb4: rockchip framebuffer registerd:fb4
[ 0.677444] rk_iommu ff930300.vopb_mmu: (vopb) Enabled
[ 0.677588] rk3288-lcdc lcdc0: lcdc0: dclk:148500000>>fps:60
[ 0.677612] rk3288-lcdc lcdc0: wakeup from standby!
[ 0.704992] usb_battery_charger_detect_synop , battery_charger_detect 1, pass DCD, dcd_state = 1
[ 0.722544] alloc_buffer:ion_phy_addr=0x10000000
[ 0.734480] fb0:phy:10000000>>vir:f0171000>>len:0x1800000
[ 0.764074] rk3288-lcdc lcdc0: lcdc0 probe ok, iommu enabled
[ 0.764471] rockchip_set_mux:warning ignore bank num 15
[ 0.764598] rockchip_set_mux:warning ignore bank num 15
[ 0.764708] rockchip_set_mux:warning ignore bank num 15
[ 0.764831] rockchip_set_mux:warning ignore bank num 15
[ 0.764936] rockchip_set_mux:warning ignore bank num 15
[ 0.765048] rockchip_set_mux:warning ignore bank num 15
[ 0.765625] rockchip_set_mux:warning ignore bank num 15
[ 0.765776] rockchip_set_mux:warning ignore bank num 15
[ 0.766321] rockchip_set_mux:warning ignore bank num 15
[ 0.766461] rockchip_set_mux:warning ignore bank num 15
[ 0.766999] rockchip_set_mux:warning ignore bank num 15
[ 0.767144] rockchip_set_mux:warning ignore bank num 15
[ 0.767682] rockchip_set_mux:warning ignore bank num 15
[ 0.767822] rockchip_set_mux:warning ignore bank num 15
[ 0.769173] NET: Registered protocol family 2
[ 0.769625] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.769763] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.769900] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.769949] TCP: reno registered
[ 0.769965] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.770001] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.770194] NET: Registered protocol family 1
[ 0.770375] Unpacking initramfs...
[ 0.832010] Freeing initrd memory: 1148K (c59fc000 - c5b1b000)
[ 0.832615] hw perfevents: enabled with ARMv7 Cortex-A12 PMU driver, 7 counters available
[ 0.833051] probe device ff9a0000.vpu_service
[ 0.833225] vpu_service: power on
[ 0.834281] checking hw id 4831
[ 0.834639] vpu_service set to auto frequency mode
[ 0.834694] vcodec vpu_service: vcodec ion client create success!
[ 0.835080] rk_iommu ff9a0800.vpu_mmu: (vpu) Enabled
[ 0.835111] rk_iommu ff9a0800.vpu_mmu: (vpu) Disabled
[ 0.835126] rk_iommu ff9a0800.vpu_mmu: rockchip_iommu_detach_device: Detached IOMMU with pgtable 0x2e26e000
[ 0.835140] vpu_service: power off...
[ 0.835177] done
[ 0.835186] init success
[ 0.835257] probe device ff9c0000.hevc_service
[ 0.835437] hevc_service: power on
[ 0.836475] checking hw id 6867
[ 0.836727] vcodec hevc_service: vcodec ion client create success!
[ 0.837001] rk_iommu ff9c0440.hevc_mmu: (hevc) Enabled
[ 0.837030] rk_iommu ff9c0440.hevc_mmu: (hevc) Disabled
[ 0.837045] rk_iommu ff9c0440.hevc_mmu: rockchip_iommu_detach_device: Detached IOMMU with pgtable 0x2e26c000
[ 0.837057] hevc_service: power off...
[ 0.837094] done
[ 0.837103] init success
[ 0.837209] rknandbase v1.0 2014-03-31
[ 0.837399] rknand_probe clk rate = 148500000
[ 0.837513] rknand_driver:ret = 0
[ 0.837857] audit: initializing netlink socket (disabled)
[ 0.837897] type=2000 audit(0.390:1): initialized
[ 0.838616] bounce pool size: 64 pages
[ 0.842989] fuse init (API version 7.22)
[ 0.843367] msgmni has been set to 1456
[ 0.845226] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 0.845245] io scheduler noop registered
[ 0.845256] io scheduler deadline registered
[ 0.845353] io scheduler cfq registered (default)
[ 0.846087] rga ff920000.rga: rga ion client create success!
[ 0.846226] rga: Driver loaded succesfully
[ 0.846656] IEP Power ON
[ 0.846693] iep ion client create success!
[ 0.847026] rk_iommu ff900800.iep_mmu: (iep) Enabled
[ 0.847053] IEP Power OFF
[ 0.847066] rk_iommu ff900800.iep_mmu: (iep) Disabled
[ 0.847081] rk_iommu ff900800.iep_mmu: rockchip_iommu_detach_device: Detached IOMMU with pgtable 0x2e261000
[ 0.847098] IEP Driver loaded succesfully
[ 0.847188] Module initialized.
[ 0.847889] dma-pl330 ffb20000.pdma: Loaded driver for PL330 DMAC-2364208
[ 0.847909] dma-pl330 ffb20000.pdma: DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10
[ 0.849116] dma-pl330 ff250000.pdma: Loaded driver for PL330 DMAC-2364208
[ 0.849136] dma-pl330 ff250000.pdma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[ 0.849365] pwm-voltage-regulator pwm_regulator.23: unable to request PWM, trying legacy API
[ 0.849384] pwm-voltage-regulator pwm_regulator.23: unable to request legacy PWM
[ 0.849396] pwm_regulator_probe:error
[ 0.849417] platform pwm_regulator.23: Driver pwm-voltage-regulator requests probe deferral
[ 0.849731] rk_serial.c v1.8 2014-03-04
[ 0.849928] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 87) is a rk29_serial.0
[ 0.850106] serial ff180000.serial: membase 0xf015e000
[ 0.852864] loop: module loaded
[ 0.853321] SCSI Media Changer driver v0.25
[ 0.853619] tun: Universal TUN/TAP device driver, 1.6
[ 0.853632] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.854135] stmmac_probe_config_dt: Can not read property: pmu_regulator.
[ 0.854151] stmmac_probe_config_dt: Can not read property: pmu_enable_level.
[ 0.854165] stmmac_probe_config_dt: clock input or output? (input).
[ 0.854178] stmmac_probe_config_dt: TX delay(0x30).
[ 0.854189] stmmac_probe_config_dt: RX delay(0x10).
[ 0.854224] stmmac_probe_config_dt: is rockchip,rk3288-gmac
[ 0.854236] stmmc_pltfr_init:
[ 0.854246] stmmc_pltfr_init: ERROR: Get power-gpio failed.
[ 0.854263] stmmc_pltfr_init: init for RGMII
[ 0.854275] tx delay=0x30
[ 0.854275] rx delay=0x10
[ 0.854712] stmmac - user ID: 0x10, Synopsys ID: 0x35
[ 0.854723]Normal descriptors
[ 0.854732]Ring mode enabled
[ 0.854742]DMA HW capability register supported
[ 0.854753]RX Checksum Offload Engine supported (type 2)
[ 0.854764]TX Checksum insertion supported
[ 0.854773]Wake-Up On Lan supported
[ 0.854806]Enable RX Mitigation via HW Watchdog Timer
[ 0.855187] PPP generic driver version 2.4.2
[ 0.855332] PPP BSD Compression module registered
[ 0.855345] PPP Deflate Compression module registered
[ 0.855365] PPP MPPE Compression module registered
[ 0.855378] NET: Registered protocol family 24
[ 0.855410] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[ 0.855424] CSLIP: code copyright 1989 Regents of the University of California.
[ 0.855437] Rockchip WiFi SYS interface (V1.00) ...
[ 0.855514] usbcore: registered new interface driver catc
[ 0.855550] usbcore: registered new interface driver kaweth
[ 0.855563] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[ 0.855599] usbcore: registered new interface driver pegasus
[ 0.855640] usbcore: registered new interface driver rtl8150
[ 0.855676] usbcore: registered new interface driver r8152
[ 0.855688] hso: drivers/net/usb/hso.c: Option Wireless
[ 0.855747] usbcore: registered new interface driver hso
[ 0.855789] usbcore: registered new interface driver asix
[ 0.855823] usbcore: registered new interface driver ax88179_178a
[ 0.855859] usbcore: registered new interface driver cdc_ether
[ 0.855898] usbcore: registered new interface driver cdc_eem
[ 0.855945] usbcore: registered new interface driver dm9601
[ 0.855980] usbcore: registered new interface driver dm9620
[ 0.856023] usbcore: registered new interface driver smsc75xx
[ 0.856067] usbcore: registered new interface driver smsc95xx
[ 0.856102] usbcore: registered new interface driver gl620a
[ 0.856140] usbcore: registered new interface driver net1080
[ 0.856177] usbcore: registered new interface driver plusb
[ 0.856212] usbcore: registered new interface driver rndis_host
[ 0.856248] usbcore: registered new interface driver cdc_subset
[ 0.856281] usbcore: registered new interface driver zaurus
[ 0.856317] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[ 0.856373] usbcore: registered new interface driver int51x1
[ 0.856409] usbcore: registered new interface driver kalmia
[ 0.856448] usbcore: registered new interface driver ipheth
[ 0.856488] usbcore: registered new interface driver sierra_net
[ 0.856526] usbcore: registered new interface driver cx82310_eth
[ 0.856572] usbcore: registered new interface driver cdc_ncm
[ 0.856608] usbcore: registered new interface driver qmi_wwan
[ 0.856643] usbcore: registered new interface driver cdc_mbim
[ 0.856656] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.859015] ehci_rk_probe f19c0000 f19c0010
[ 0.859033] rockchip_ehci_host ff500000.usb: Rockchip On-Chip EHCI Host Controller
[ 0.859063] rockchip_ehci_host ff500000.usb: new USB bus registered, assigned bus number 1
[ 0.859370] rockchip_ehci_host ff500000.usb: irq 56, io mem 0xff500000
[ 0.871832] rockchip_ehci_host ff500000.usb: USB 0.0 started, EHCI 1.00
[ 0.871906] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.871922] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.871937] usb usb1: Product: Rockchip On-Chip EHCI Host Controller
[ 0.871951] usb usb1: Manufacturer: Linux 3.10.0 ehci_hcd
[ 0.871964] usb usb1: SerialNumber: ff500000.usb
[ 0.872390] hub 1-0:1.0: USB hub found
[ 0.872416] hub 1-0:1.0: 1 port detected
[ 0.901382] ehci_rk_probe ok
[ 0.901524] usbcore: registered new interface driver cdc_acm
[ 0.901537] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 0.901589] usbcore: registered new interface driver usblp
[ 0.901629] usbcore: registered new interface driver cdc_wdm
[ 0.901687] usbcore: registered new interface driver usb-storage
[ 0.901723] usbcore: registered new interface driver ums-alauda
[ 0.901764] usbcore: registered new interface driver ums-cypress
[ 0.901802] usbcore: registered new interface driver ums-datafab
[ 0.901837] usbcore: registered new interface driver ums_eneub6250
[ 0.901872] usbcore: registered new interface driver ums-freecom
[ 0.901908] usbcore: registered new interface driver ums-isd200
[ 0.901943] usbcore: registered new interface driver ums-jumpshot
[ 0.901978] usbcore: registered new interface driver ums-karma
[ 0.902013] usbcore: registered new interface driver ums-onetouch
[ 0.902048] usbcore: registered new interface driver ums-sddr09
[ 0.902083] usbcore: registered new interface driver ums-sddr55
[ 0.902118] usbcore: registered new interface driver ums-usbat
[ 0.902208] usbcore: registered new interface driver usbserial
[ 0.902248] usbcore: registered new interface driver usbserial_generic
[ 0.902281] usbserial: USB Serial support registered for generic
[ 0.902320] usbcore: registered new interface driver option
[ 0.902351] usbserial: USB Serial support registered for GSM modem (1-port)
[ 0.902416] usbcore: registered new interface driver trancevibrator
[ 0.902429] usb20_otg: version 3.10a 21-DEC-2012
[ 0.902774] f1a00040
[ 0.902788] Core Release: 3.10a
[ 0.902799] Setting default values for core params
[ 0.902943] Using Buffer DMA mode
[ 0.902956] Periodic Transfer Interrupt Enhancement - disabled
[ 0.902967] Multiprocessor Interrupt Enhancement - disabled
[ 0.902979] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 0.902990] ^^^^^^^^^^^^^^^^^Device Mode
[ 0.903003] Dedicated Tx FIFOs mode
[ 0.903020] pcd_init otg_dev = ed9bfec0
[ 0.903157] usb20_otg ff580000.usb: DWC OTG Controller
[ 0.903189] usb20_otg ff580000.usb: new USB bus registered, assigned bus number 2
[ 0.903219] usb20_otg ff580000.usb: irq 55, io mem 0x00000000
[ 0.903280] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.903298] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.903313] usb usb2: Product: DWC OTG Controller
[ 0.903325] usb usb2: Manufacturer: Linux 3.10.0 dwc_otg_hcd
[ 0.903338] usb usb2: SerialNumber: ff580000.usb
[ 0.903713] hub 2-0:1.0: USB hub found
[ 0.903736] hub 2-0:1.0: 1 port detected
[ 0.904002] usb20_host: version 3.10a 21-DEC-2012
[ 0.906411] f1a80040
[ 0.906424] Core Release: 3.10a
[ 0.906435] Setting default values for core params
[ 0.906562] Using Buffer DMA mode
[ 0.906574] Periodic Transfer Interrupt Enhancement - disabled
[ 0.906584] Multiprocessor Interrupt Enhancement - disabled
[ 0.906596] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 0.906606] ^^^^^^^^^^^^^^^^^^Host Mode
[ 0.906633] usb20_host ff540000.usb: DWC OTG Controller
[ 0.906658] usb20_host ff540000.usb: new USB bus registered, assigned bus number 3
[ 0.906687] usb20_host ff540000.usb: irq 57, io mem 0x00000000
[ 0.906780] Init: Power Port (0)
[ 0.906834] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.906850] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.906865] usb usb3: Product: DWC OTG Controller
[ 0.906878] usb usb3: Manufacturer: Linux 3.10.0 dwc_otg_hcd
[ 0.906891] usb usb3: SerialNumber: ff540000.usb
[ 0.907264] hub 3-0:1.0: USB hub found
[ 0.907289] hub 3-0:1.0: 1 port detected
[ 0.907778] .. rk pwm remotectl v1.0 init
[ 0.907859] remotectl probe j=0x0
[ 0.908009] input: ff680000.pwm as /devices/ff680000.pwm/input/input0
[ 0.908223] pwm enable val=0x646205
[ 0.908474] usbcore: registered new interface driver xpad
[ 0.908527] usbcore: registered new interface driver usb_acecad
[ 0.908578] usbcore: registered new interface driver aiptek
[ 0.908621] usbcore: registered new interface driver gtco
[ 0.908661] usbcore: registered new interface driver hanwang
[ 0.908701] usbcore: registered new interface driver kbtab
[ 0.908747] usbcore: registered new interface driver wacom
[ 0.909069] sensor_register_slave:mma8452,id=17
[ 0.909084] sensor_register_slave:cm3217,id=44
[ 0.909096] sensor_register_slave:cm3218,id=45
[ 0.913655] rtc_hym8563 0-0051: rtc core: registered hym8563 as rtc0
[ 0.913702] i2c /dev entries driver
[ 0.914335] IR NEC protocol handler initialized
[ 0.914349] IR RC5(x) protocol handler initialized
[ 0.914359] IR RC6 protocol handler initialized
[ 0.914369] IR JVC protocol handler initialized
[ 0.914379] IR Sony protocol handler initialized
[ 0.914389] IR RC5 (streamzap) protocol handler initialized
[ 0.914399] IR SANYO protocol handler initialized
[ 0.914409] IR MCE Keyboard/mouse protocol handler initialized
[ 0.914485] usbcore: registered new interface driver uvcvideo
[ 0.914497] USB Video Class driver (1.1.1)
[ 0.915199] rockchip_temp_probe,line=362
[ 0.915489] tsadc ff280000.tsadc: initialized
[ 0.915838] device-mapper: uevent: version 1.0.3
[ 0.916077] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[ 0.916364] Bluetooth: HCI UART driver ver 2.2
[ 0.916379] Bluetooth: HCI H4 protocol initialized
[ 0.916391] Bluetooth: HCILL protocol initialized
[ 0.919413] cpufreq version 1.0, suspend freq 816 MHz
[ 0.919582] cpuidle: using governor ladder
[ 0.919595] cpuidle: using governor menu
[ 0.919630] Synopsys Designware Multimedia Card Interface Driver
[ 0.919860] dwmmc_rockchip ff0f0000.rksdmmc: Version ID is 270a
[ 0.920130] dwmmc_rockchip ff0f0000.rksdmmc: Using internal DMA controller.
[ 0.920282] 3220..dw_mci_init_slot: fmin=400000, fmax=100000000
[ 0.920298] Line3225..dw_mci_init_slot: The rk_sdmmc Ver 1.12 2014-07-08
[ 0.920412] 1347..dw_mci_set_ios:no card.
[ 0.930885] 1347..dw_mci_set_ios:no card.
[ 0.950587] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out 800000Hz for init
[ 0.950623] dwmmc_rockchip ff0f0000.rksdmmc: DW MMC controller at irq 67, 32 bit host data width, 256 deep fifo
[ 0.950642] dwmmc_rockchip ff0f0000.rksdmmc: 1 slots initialized
[ 0.950903] dwmmc_rockchip ff0c0000.rksdmmc: Version ID is 270a
[ 0.951728] dwmmc_rockchip ff0c0000.rksdmmc: Using internal DMA controller.
[ 0.951898] 3214..dw_mci_init_slot: fmin=300000, fmax=50000000
[ 0.952271] 1347..dw_mci_set_ios:no card.
[ 0.970237] 1347..dw_mci_set_ios:no card.
[ 0.982686] mmc0: BKOPS_EN bit is not set
[ 0.984561] rk_sdmmc: BOOT Bus speed=0Hz,Bus width=8bits.
[ 0.986842] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0)
[ 0.986865] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out normal clock
[ 0.986988] rk_sdmmc: BOOT
[ 0.986988]execute tuning: candidates_degree = SDMMC_SHIFT_DEGREE_0 SDMMC_SHIFT_DEGREE_90 SDMMC_SHIFT_DEGREE_180 SDMMC_SHIFT_DEGREE_INVALID
[ 0.987039] mmc0: new HS200 MMC card at address 0001
[ 0.987292] mmcblk0: mmc0:0001 AWMB3R 14.5 GiB
[ 0.987566] uboot: 0x000400000 -- 0x000800000 (4 MB)
[ 0.987578] misc: 0x000800000 -- 0x000c00000 (4 MB)
[ 0.987587] resource: 0x000c00000 -- 0x001c00000 (16 MB)
[ 0.987596] kernel: 0x001c00000 -- 0x002c00000 (16 MB)
[ 0.987605] boot: 0x002c00000 -- 0x004c00000 (32 MB)
[ 0.987613] recovery: 0x004c00000 -- 0x006c00000 (32 MB)
[ 0.987622] backup: 0x006c00000 -- 0x00a000000 (52 MB)
[ 0.987630] cache: 0x00a000000 -- 0x012000000 (128 MB)
[ 0.987638] kpanic: 0x012000000 -- 0x012400000 (4 MB)
[ 0.987646] system: 0x012400000 -- 0x042400000 (768 MB)
[ 0.987655] metadata: 0x042400000 -- 0x042800000 (4 MB)
[ 0.987663] userdata: 0x042800000 -- 0x082800000 (1024 MB)
[ 0.987672] radical_update: 0x082800000 -- 0x086800000 (64 MB)
[ 0.987680] user: 0x086800000 -- 0x3a3a00000 (12754 MB)
[ 0.987705]mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p141347..dw_mci_set_ios:no card.
[ 0.990028] dwmmc_rockchip ff0c0000.rksdmmc: DW MMC controller at irq 64, 32 bit host data width, 256 deep fifo
[ 0.990041] dwmmc_rockchip ff0c0000.rksdmmc: 1 slots initialized
[ 0.990295] dwmmc_rockchip ff0d0000.rksdmmc: Version ID is 270a
[ 0.990498] dwmmc_rockchip ff0d0000.rksdmmc: Using internal DMA controller.
[ 0.990598] 3220..dw_mci_init_slot: fmin=200000, fmax=50000000
[ 0.990680] 1347..dw_mci_set_ios:no card.
[ 1.009579] 1347..dw_mci_set_ios:no card.
[ 1.029271] 1347..dw_mci_set_ios:no card.
[ 1.029445] dwmmc_rockchip ff0d0000.rksdmmc: DW MMC controller at irq 65, 32 bit host data width, 256 deep fifo
[ 1.029458] dwmmc_rockchip ff0d0000.rksdmmc: 1 slots initialized
[ 1.029708] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.030924] usbcore: registered new interface driver usbhid
[ 1.030934] usbhid: USB HID core driver
[ 1.031201] ashmem: initialized
[ 1.031309] logger: created 256K log 'log_main'
[ 1.031402] logger: created 256K log 'log_events'
[ 1.031492] logger: created 256K log 'log_radio'
[ 1.031582] logger: created 256K log 'log_system'
[ 1.032403] input: rk29-keypad as /devices/ff100000.adc/key.33/input/input1
[ 1.033163] es8323 probe i2c recv ok
[ 1.033366] i2c-core: driver using legacy suspend method
[ 1.033377] i2c-core: driver using legacy resume method
[ 1.033667] rockchip_i2s_probe()
[ 1.033816] rockchip_snd_txctrl: off
[ 1.033824] rockchip_snd_txctrl: stop xfer
[ 1.033832] rockchip_snd_rxctrl: off
[ 1.033838] rockchip_snd_rxctrl: stop xfer
[ 1.034035] rockchip-hdmi-spdif rockchip-hdmi-spdif.27: ASoC: CPU DAI (null) not registered
[ 1.034061] rockchip_hdmi_spdif_audio_probe() register card failed:-517
[ 1.034079] platform rockchip-hdmi-spdif.27: Driver rockchip-hdmi-spdif requests probe deferral
[ 1.034284] es8323_probe
[ 1.034362] es8323_probe:register ISR (irq=194)
[ 1.245792] Using Buffer DMA mode
[ 1.245801] Periodic Transfer Interrupt Enhancement - disabled
[ 1.245807] Multiprocessor Interrupt Enhancement - disabled
[ 1.245813] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 1.245819] ^^^^^^^^^^^^^^^^^^Host Mode
[ 1.294977] Init: Power Port (0)
[ 1.669223] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> NULL --> Left Line Mux
[ 1.669234] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> NULL -> Left Line Mux
[ 1.669245] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> NULL --> Left Line Mux
[ 1.669253] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> NULL -> Left Line Mux
[ 1.669262] ES8323 2-0010: ASoC: no dapm match for Left PGA Mux --> NULL --> Left Line Mux
[ 1.669270] ES8323 2-0010: ASoC: Failed to add route Left PGA Mux -> NULL -> Left Line Mux
[ 1.669281] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> NULL --> Right Line Mux
[ 1.669289] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> NULL -> Right Line Mux
[ 1.669298] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> NULL --> Right Line Mux
[ 1.669306] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> NULL -> Right Line Mux
[ 1.669315] ES8323 2-0010: ASoC: no dapm match for Right PGA Mux --> NULL --> Right Line Mux
[ 1.669323] ES8323 2-0010: ASoC: Failed to add route Right PGA Mux -> NULL -> Right Line Mux
[ 1.669332] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> LAMP --> Left PGA Mux
[ 1.669340] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> LAMP -> Left PGA Mux
[ 1.669349] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> LAMP --> Left PGA Mux
[ 1.669357] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> LAMP -> Left PGA Mux
[ 1.669366] ES8323 2-0010: ASoC: no dapm match for Differential Mux --> LAMP --> Left PGA Mux
[ 1.669375] ES8323 2-0010: ASoC: Failed to add route Differential Mux -> LAMP -> Left PGA Mux
[ 1.669384] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> RAMP --> Right PGA Mux
[ 1.669391] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> RAMP -> Right PGA Mux
[ 1.669400] ES83s3e2-@r102 A:/C: no dapm match for RINPUT2 --> RAMP --> Right PGA Mux
[ 1.669407] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> RAMP -> Right PGA Mux
[ 1.669416] ES8323 2-0010: ASoC: no dapm match for Differential Mux --> RAMP --> Right PGA Mux
[ 1.669424] ES8323 2-0010: ASoC: Failed to add route Differential Mux -> RAMP -> Right PGA Mux
[ 1.669433] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> LAMP --> Differential Mux
[ 1.669441] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> LAMP -> Differential Mux
[ 1.669450] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> RAMP --> Differential Mux
[ 1.669457] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> RAMP -> Differential Mux
[ 1.669465] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> LAMP --> Differential Mux
[ 1.669473] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> LAMP -> Differential Mux
[ 1.669481] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> RAMP --> Differential Mux
[ 1.669488] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> RAMP -> Differential Mux
[ 1.669508] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> LAMP --> Left Line Mux
[ 1.669516] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> LAMP -> Left Line Mux
[ 1.669524] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> LAMP --> Left Line Mux
[ 1.669532] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> LAMP -> Left Line Mux
[ 1.669542] ES8323 2-0010: ASoC: no dapm match for Left PGA Mux --> LAMP --> Left Line Mux
[ 1.669550] ES8323 2-0010: ASoC: Failed to add route Left PGA Mux -> LAMP -> Left Line Mux
[ 1.669559] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> RAMP --> Right Line Mux
[ 1.669567] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> RAMP -> Right Line Mux
[ 1.669576] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> RAMP --> Right Line Mux
[ 1.669584] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> RAMP -> Right Line Mux
[ 1.669593] ES8323 2-0010: ASoC: no dapm match for Right PGA Mux --> RAMP --> Right Line Mux
[ 1.669601] ES8323 2-0010: ASoC: Failed to add route Right PGA Mux -> RAMP -> Right Line Mux
[ 1.669712] ES8323 2-0010: ASoC: mux Right Line Mux has no paths
[ 1.669724] ES8323 2-0010: ASoC: mux Left Line Mux has no paths
[ 1.669735] ES8323 2-0010: ASoC: mux Right PGA Mux has no paths
[ 1.669745] ES8323 2-0010: ASoC: mux Left PGA Mux has no paths
[ 1.669777] ES8323 2-0010: ASoC: mux Differential Mux has no paths
[ 1.672321] Enter::rk29_es8323_init----123
[ 1.675005] rockchip-es8323 rockchip-es8323.29:ES8323 HiFi <-> rockchip-i2s.0 mapping ok
[ 1.677033] u32 classifier
[ 1.677040] Actions configured
[ 1.677049] Netfilter messages via NETLINK v0.30.
[ 1.677091] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 1.677335] ctnetlink v0.93: registering with nfnetlink.
[ 1.677381] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 1.677387] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 1.677594] xt_time: kernel timezone is -0000
[ 1.677749] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.677845] arp_tables: (C) 2002 David S. Miller
[ 1.677876] TCP: cubic registered
[ 1.677881] Initializing XFRM netlink socket
[ 1.678054] NET: Registered protocol family 10
[ 1.678431] mip6: Mobile IPv6
[ 1.678452] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 1.678543] sit: IPv6 over IPv4 tunneling driver
[ 1.678810] NET: Registered protocol family 17
[ 1.678829] NET: Registered protocol family 15
[ 1.678868] Bridge firewalling registered
[ 1.678878] Ebtables v2.0 registered
[ 1.678990] Bluetooth: RFCOMM TTY layer initialized
[ 1.679009] Bluetooth: RFCOMM socket layer initialized
[ 1.679016] Bluetooth: RFCOMM ver 1.11
[ 1.679022] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 1.679028] Bluetooth: BNEP filters: protocol multicast
[ 1.679037] Bluetooth: BNEP socket layer initialized
[ 1.679043] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 1.679052] Bluetooth: HIDP socket layer initialized
[ 1.679072] l2tp_core: L2TP core driver, V2.0
[ 1.679083] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 1.679089] : Enter rfkill_wlan_init
[ 1.679232] : Enter rfkill_wlan_probe
[ 1.679241] wlan_platdata_parse_dt: wifi_chip_type = bcmwifi
[ 1.679248] : wlan_platdata_parse_dt: enable wifi power control.
[ 1.679255] : wlan_platdata_parse_dt: disable wifi io reference voltage control.
[ 1.679263] : wlan_platdata_parse_dt: wifi power controled by gpio.
[ 1.﨑DR Version 1.00 20141007
In
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Memory OK
Memory OK
OUT
U-Boot 2014.10-RK3288-02 (Oct 30 2014 - 09:27:41)
CPU: rk3288
CPU's clock information:
arm pll = 600000000HZ
periph pll = 300000000HZ
ddr pll = 200000000HZ
codec pll = 594000000HZ
Board: Rockchip platform Board
DRAM:Found dram banks:1
Adding bank:0000000000000000(0000000080000000)
128 MiB
storage init OK!
Using default environment
GetParam
check parameter success
Unknow param: MACHINE_MODEL:rk30sdk!
Unknow param: MACHINE_ID:007!
Unknow param: MANUFACTURER:RK30SDK!
Unknow param: PWR_HLD: 0,0,A,0,1!
failed to prepare fdt from boot!
power key: bank-0 pin-5
can't find dts node for ricoh619
pmic:act8846
Can't find dts node for fuel guage cw201x
SecureBootEn = 0, SecureBootLock = 0
#Boot ver: 2014-10-30#2.17
sn:1006110001000029
no fuel gauge found
no fuel gauge found
read logo_on switch from dts
checkKey
vbus = 1
no fuel gauge found
Hit any key to stop autoboot:0
failed to load fdt from boot!
kernel @ 0x02000000 (0x005f3258)
ramdisk@ 0x059fc000 (0x0011f742)
Secure Boot state: 0
bootrk: do_bootm_linux...
Loading Device Tree to 0561c000, end 05636cc8 ... OK
Add bank:0000000000000000, 0000000080000000
Starting kernel ...
<hit enter to activate fiq debugger>
[ 0.000000] Booting Linux on physical CPU 0x500
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct