板子没有接任何显示设备，就老是提示这个
指示灯时按时灭，打印信息打印这个，断断续续，请问这个是什么意思啊？[ 61.758344] Suspended for 0.000 seconds
[ 61.759462] Enabling non-boot CPUs ...
[ 61.760083] CPU1: Booted secondary processor
[ 61.761317] CPU1 is up
[ 61.761718] CPU2: Booted secondary processor
[ 61.762360] CPU2 is up
[ 61.762764] CPU3: Booted secondary processor
[ 61.763391] CPU3 is up
[ 61.766096] PM: noirq resume of devices complete after 2.713 msecs
[ 61.766809] PM: early resume of devices complete after 0.460 msecs
[ 61.767265] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 52000000Hz, actual 50000000HZ div = 1)
[ 61.767279] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out normal clock
[ 61.767649] 1390..dw_mci_set_ios:no card.
[ 61.767715] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[ 61.767726] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out normal clock
[ 61.767894] dwc_otg_hcd_resume, usb device mode
[ 61.768116] ff540000.usb resume, HPRT0:0x1485
[ 61.773066] phy_power_on: enable = 1
[ 61.807814] : Enter rfkill_wlan_resume
[ 61.810782] rk_spdif:spdif:Entered spdif_resume
[ 62.182106] usb 3-1.4: reset low-speed USB device number 3 using usb20_host
[ 62.471822] PM: resume of devices complete after 716.452 msecs
[ 62.472172] cpufreq: cpufreq_resume: Failed to start governor for policy: ee392f00
[ 62.472184] cpufreq: cpufreq_resume: Failed to start governor for policy: ee392f00
[ 62.472193] cpufreq: cpufreq_resume: Failed to start governor for policy: ee392f00
[ 62.473184] : ** disable irq
[ 62.738527] Restarting tasks ... done.
[ 62.745418] PM: suspend exit 2011-01-01 12:01:21.951298250 UTC
[ 64.563561] PM: suspend entry 2011-01-01 12:01:23.798884751 UTC
[ 64.569587] PM: Syncing filesystems ... done.
[ 64.613212] Freezing user space processes ... (elapsed 0.006 seconds) done.
[ 64.626214] Freezing remaining freezable tasks ... (elapsed 0.004 seconds) done.
[ 64.638144] Suspending console(s) (use no_console_suspend to debug)
01-armoff-logdp-osc_offddrc_off2345d
如果是RK3288的板子，先确认电源是电压5V，电流2.5A以上 本帖最后由 jjlin77 于 2015-12-7 10:54 编辑
暴走的阿Sai 发表于 2015-12-7 10:30
如果是RK3288的板子，先确认电源是电压5V，电流2.5A以上
我确认是5V-2.5A 只要我接上HDMI的显示器，就不会提示这个，它提示这个不是重启，是断断续续，程序感觉是在跑的,进入了suspended状态吧 jjlin77 发表于 2015-12-7 10:42
我确认是5V-2.5A 只要我接上HDMI的显示器，就不会提示这个，它提示这个不是重启，是断断续续，程序感觉是 ...
恩 是休眠状态！
有中端唤醒机器了 tangyu1121 发表于 2015-12-7 15:54
恩 是休眠状态！
有中端唤醒机器了
那这位大哥，你知道怎么调，不接HDMI，也不让他进入休眠状态吗？我现在没有屏幕，电视机和电脑不能随便搬动，所以，很多情况都是直接adb debug，不接屏幕，所以需要不接屏幕也不进入休眠啊 jjlin77 发表于 2015-12-7 16:06
那这位大哥，你知道怎么调，不接HDMI，也不让他进入休眠状态吗？我现在没有屏幕，电视机和电脑不能随便搬 ...
1、可以把设置里面安全-》屏幕锁定-》 这个设置项设置为无；
2、然后把机器的休眠时间：设置为永不休眠 ---这个在论坛上有解决方法的你搜索一下
这样机器开起来之后就不会进去休眠模式了 楼主解决了吗？我也遇到了
页:
[1]