Firefly开源社区

标题: android pad 烧写后系统起不来 [打印本页]
作者: zhutousame    时间: 2015-3-31 09:57
标题: android pad 烧写后系统起不来
android pad 烧写后系统起不来
1.安装官网链接 http://wiki.t-firefly.com/index.php/Firefly-RK3288/Build_android，编译了pad版本的android，我更新到最新版的代码（git pull bitbucket pad:pad），编译正式版(0930)开发板的内核，将生成的img拷出来烧写的时候发现系统起不来。
2.经过测试发现了三个问题：
  A.第一个问题单独烧写misc.img固件，导致系统进入recovery，串口如下：
  1. DDR Version 1.00 20141007
  2. In
  3. SRX
  4. Channel a: DDR3 200MHz
  5. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
  6. Channel b: DDR3 200MHz
  7. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
  8. OUT


  11. U-Boot 2014.10-RK3288-01 (Nov 27 2014 - 16:44:27)

  13. CPU: rk3288
  14. CPU's clock information:
  15.     arm pll = 600000000HZ
  16.     periph pll = 297000000HZ
  17.     ddr pll = 200000000HZ
  18.     codec pll = 384000000HZ
  19. Board:  Rockchip platform Board
  20. DRAM:  Found dram banks:1
  21. Adding bank:0000000000000000(0000000080000000)
  22. 128 MiB
  23. storage init OK!
  24. Using default environment

  26. GetParam
  27. check parameter success
  28. Unknow param: MACHINE_MODEL:rk30sdk!
  29. Unknow param: MACHINE_ID:007!
  30. Unknow param: MANUFACTURER:RK30SDK!
  31. Unknow param: PWR_HLD: 0,0,A,0,1!
  32. failed to prepare fdt from boot!
  33. power key: bank-0 pin-5
  34. pmic:act8846
  35. SecureBootEn = 0, SecureBootLock = 0

  37. #Boot ver: 2014-11-27#2.19
  38. sn:100612000000019D
  39. checkKey
  40. vbus = 1
  41. no fuel gauge found
  42. no fuel gauge found
  43. read logo_on switch from dts [0]
  44. no fuel gauge found
  45. got recovery cmd from misc.
  46. failed to load fdt from recovery!
  47. kernel   @ 0x02000000 (0x00659f60)
  48. ramdisk  @ 0x04bf0000 (0x003d1840)
  49. Secure Boot state: 0
  50. bootrk: do_bootm_linux...
  51.    Loading Device Tree to 0480d000, end 0482aaf9 ... OK
  52. Add bank:0000000000000000, 0000000080000000

  54. Starting kernel ...

  56. <hit enter to activate fiq debugger>
  57. [    0.000000] Booting Linux on physical CPU 0x500
  58. [    0.000000] Initializing cgroup subsys cpu
  59. [    0.000000] Initializing cgroup subsys cpuacct
  60. [    0.000000] Linux version 3.10.0 (firefly@midserver) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #3 SMP PREEMPT Tue Dec         30 15:45:08 CST 2014
  61. [    0.000000] CPU: ARMv7 Processor [410fc0d1] revision 1 (ARMv7), cr=10c5387d
  62. [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  63. [    0.000000] Machine: Rockchip RK3288 (Flattened Device Tree), model: rockchip,rk3288
  64. [    0.000000] rockchip_ion_reserve
  65. [    0.000000] ion heap(cma): base(40000000) size(28000000) align(0)
  66. [    0.000000] ion heap(vmalloc): base(0) size(0) align(0)
  67. [    0.000000] cma: CMA: reserved 640 MiB at 40000000
  68. [    0.000000] ion_reserve: cma reserved base 40000000 size 671088640
  69. [    0.000000] cma: CMA: reserved 16 MiB at 2e800000
  70. [    0.000000] Memory policy: ECC disabled, Data cache writealloc
  71. [    0.000000] Boot mode: RECOVERY (2) flag: RECOVER (0xc3524203)
  72. [    0.000000] PERCPU: Embedded 9 pages/cpu @c1dea000 s14016 r8192 d14656 u36864
  73. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 522768
  74. [    0.000000] Kernel command line: console=ttyFIQ0 androidboot.hardware=rk30board androidboot.console=ttyFIQ0 board.ap_has_alsa=0 init        =/init  mtdparts=rk29xxnand:0x00002000@0x00000000(parameter),0x00002000@0x00002000(uboot),0x00002000@0x00004000(misc),0x00008000@0x0000        6000(resource),0x00008000@0x0000e000(kernel),0x00010000@0x00016000(boot),0x00010000@0x00026000(recovery),0x0001a000@0x00036000(backup),        0x00040000@0x00050000(cache),0x00002000@0x00090000(kpanic),0x00180000@0x00092000(system),0x00002000@0x00212000(metadata),0x00200000@0x0        0214000(userdata),0x00020000@0x00414000(radical_update),-@0x00434000(user) storagemedia=emmc loader.timestamp=2014-11-27_16:44:27 andro        idboot.serialno=100612000000019D
  75. [    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
  76. [    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
  77. [    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
  78. [    0.000000] allocated 4194304 bytes of page_cgroup
  79. [    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
  80. [    0.000000] Memory: 2048MB = 2048MB total
  81. [    0.000000] Memory: 1385680k/1385680k available, 711472k reserved, 663552K highmem
  82. [    0.000000] Virtual kernel memory layout:
  83. [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
  84. [    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
  85. [    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
  86. [    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
  87. [    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
  88. [    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
  89. [    0.000000]       .text : 0xc0008000 - 0xc0af04ac   (11170 kB)
  90. [    0.000000]       .init : 0xc0af1000 - 0xc0b856c0   ( 594 kB)
  91. [    0.000000]       .data : 0xc0b86000 - 0xc0c8e9b8   (1059 kB)
  92. [    0.000000]        .bss : 0xc0c8e9b8 - 0xc0daca04   (1145 kB)
  93. [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
  94. [    0.000000] Preemptible hierarchical RCU implementation.
  95. [    0.000000]  RCU dyntick-idle grace-period acceleration is enabled.
  96. [    0.000000] NR_IRQS:16 nr_irqs:16 16
  97. [    0.000000] rk_clk_tree_init start! cru base = 0xfed00000
  98. [    0.000000] rk_get_uboot_display_flag: uboot_logo_on = 0
  99. [    0.000000] rkclk_init_clks: cnt_parent = 7
  100. [    0.000000] rkclk_init_clks: cnt_rate = 31
  101. [    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
  102. [    0.000000] Switching to timer-based delay loop
  103. [    0.000000] sched_clock: ARM arch timer >56 bits at 24000kHz, resolution 41ns
  104. [    0.000000] process version: 1
  105. [    0.000000] channel:0, lkg:55
  106. [    0.000000] target-temp:80
  107. [    0.000000] channel:2, lkg:0
  108. [    0.000000] target-temp:80
  109. [    0.000000] channel:0, lkg:55
  110. [    0.000000] target-temp:80
  111. [    0.000000] channel:1, lkg:58
  112. [    0.000000] target-temp:80
  113. [    0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
  114. [    0.304981] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
  115. [    0.304996] pid_max: default: 32768 minimum: 301
  116. [    0.305100] Security Framework initialized
  117. [    0.305118] SELinux:  Initializing.
  118. [    0.305189] Mount-cache hash table entries: 512
  119. [    0.305826] Initializing cgroup subsys debug
  120. [    0.305840] Initializing cgroup subsys memory
  121. [    0.305867] Initializing cgroup subsys freezer
  122. [    0.305896] CPU: Testing write buffer coherency: ok
  123. [    0.306205] /cpus/cpu@0 missing clock-frequency property
  124. [    0.306218] /cpus/cpu@1 missing clock-frequency property
  125. [    0.306228] /cpus/cpu@2 missing clock-frequency property
  126. [    0.306237] /cpus/cpu@3 missing clock-frequency property
  127. [    0.306298] CPU0: thread -1, cpu 0, socket 5, mpidr 80000500
  128. [    0.306348] Setting up static identity map for 0xc07df1a8 - 0xc07df200
  129. [    0.309425] last_log: 0x2e100000 map to 0xf0004000 and copy to 0xf0086000, size 0x80000 early 0x16e1 (version 3.0)
  130. [    0.383098] CPU1: Booted secondary processor
  131. [    0.383132] CPU1: thread -1, cpu 1, socket 5, mpidr 80000501
  132. [    0.402781] CPU2: Booted secondary processor
  133. [    0.402806] CPU2: thread -1, cpu 2, socket 5, mpidr 80000502
  134. [    0.422493] CPU3: Booted secondary processor
  135. [    0.422516] CPU3: thread -1, cpu 3, socket 5, mpidr 80000503
  136. [    0.422617] Brought up 4 CPUs
  137. [    0.422645] SMP: Total of 4 processors activated (192.00 BogoMIPS).
  138. [    0.422653] CPU: All CPU(s) started in SVC mode.
  139. [    0.423368] devtmpfs: initialized
  140. [    0.428318] pinctrl core: initialized pinctrl subsystem
  141. [    0.428567] regulator-dummy: no parameters
  142. [    0.439938] NET: Registered protocol family 16
  143. [    0.441736] DMA: preallocated 256 KiB pool for atomic coherent allocations
  144. [    0.442085] ion_snapshot: 0x2e248000 map to 0xf0107000 and copy to 0xc0d88004 (version 0.1)
  145. [    0.442448] Registered FIQ tty driver
  146. [    0.443789] console [ttyFIQ0] enabled
  147. [    0.443974] Registered fiq debugger ttyFIQ0
  148. [    0.444546] rockchip_get_bank_data:name=base start=0xff750000,end=0xff7500ff
  149. [    0.444570] rockchip_get_bank_data:name=mux_bank0 start=0xff730084,end=0xff73008f
  150. [    0.444589] rockchip_get_bank_data:name=pull_bank0 start=0xff730064,end=0xff73006f
  151. [    0.444608] rockchip_get_bank_data:name=drv_bank0 start=0xff730070,end=0xff73007b
  152. [    0.444706] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio1@ff780000 start=0xff780000,end=0xff7800ff
  153. [    0.444773] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio2@ff790000 start=0xff790000,end=0xff7900ff
  154. [    0.444838] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio3@ff7a0000 start=0xff7a0000,end=0xff7a00ff
  155. [    0.444901] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio4@ff7b0000 start=0xff7b0000,end=0xff7b00ff
  156. [    0.444965] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio5@ff7c0000 start=0xff7c0000,end=0xff7c00ff
  157. [    0.445029] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio6@ff7d0000 start=0xff7d0000,end=0xff7d00ff
  158. [    0.445094] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio7@ff7e0000 start=0xff7e0000,end=0xff7e00ff
  159. [    0.445159] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio8@ff7f0000 start=0xff7f0000,end=0xff7f00ff
  160. [    0.445229] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio15@ff7f2000 start=0xff7f2000,end=0xff7f20ff
  161. [    0.445296] rockchip_pinctrl_probe:name=RK3288-GPIO,type=3
  162. [    0.445312] rockchip_pinctrl_probe:name=base start=0xff770000,end=0xff77013f
  163. [    0.445327] rockchip_pinctrl_probe:name=pull start=0xff770140,end=0xff7701bf
  164. [    0.445341] rockchip_pinctrl_probe:name=drv start=0xff7701c0,end=0xff77023f
  165. [    0.445850] rockchip_interrupts_register:bank_num=7
  166. [    0.447772] rockchip_pinctrl_probe:init ok
  167. [    0.453736] rk_iommu ff900800.iep_mmu: (iep) Enter
  168. [    0.453829] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
  169. [    0.453846] rk_iommu ff900800.iep_mmu: (iep) Initialized
  170. [    0.454018] rk_iommu ff950800.vip_mmu: (vip) Enter
  171. [    0.454090] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
  172. [    0.454105] rk_iommu ff950800.vip_mmu: (vip) Initialized
  173. [    0.454263] rk_iommu ff930300.vopb_mmu: (vopb) Enter
  174. [    0.454336] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
  175. [    0.454351] rk_iommu ff930300.vopb_mmu: (vopb) Initialized
  176. [    0.454515] rk_iommu ff940300.vopl_mmu: (vopl) Enter
  177. [    0.454587] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
  178. [    0.454602] rk_iommu ff940300.vopl_mmu: (vopl) Initialized
  179. [    0.454765] rk_iommu ff9c0440.hevc_mmu: (hevc) Enter
  180. [    0.454842] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
  181. [    0.454858] rk_iommu ff9c0440.hevc_mmu: (hevc) Initialized
  182. [    0.455021] rk_iommu ff9a0800.vpu_mmu: (vpu) Enter
  183. [    0.455093] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
  184. [    0.455108] rk_iommu ff9a0800.vpu_mmu: (vpu) Initialized
  185. [    0.455287] rk_iommu ff914000.isp_mmu: (isp_mmu) Enter
  186. [    0.455360] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
  187. [    0.455375] rk_iommu ff914000.isp_mmu: (isp_mmu) Initialized
  188. [    0.457067] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
  189. [    0.457084] hw-breakpoint: maximum watchpoint size is 4 bytes.
  190. [    0.457292] DDR DEBUG: version 1.00 20140603
  191. [    0.457323] DDR DEBUG: Channel a:
  192. [    0.457333] DDR DEBUG: DDR3 Device
  193. [    0.457348] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Total Capability=1024MB
  194. [    0.457360] DDR DEBUG: Channel b:
  195. [    0.457369] DDR DEBUG: DDR3 Device
  196. [    0.457383] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Total Capability=1024MB
  197. [    0.457395] DDR DEBUG: addr=0xc96000
  198. [    0.457407] DDR DEBUG: stride=9, size=256, halfcap=40000000
  199. [    0.457418] DDR DEBUG: socAddr[0]=0xc96000, socAddr[1]=0xc96100
  200. [    0.457430] DDR DEBUG: chAddr[0]=0xc96000, chAddr[1]=0xc96000
  201. [    0.457443] DDR DEBUG: dtar[0]=0x60192000, dtar[1]=0x60192000
  202. [    0.457690] DDR DEBUG: init success!!! freq=300MHz
  203. [    0.457700] DDR DEBUG: Channel a:
  204. [    0.457714] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
  205. [    0.457730] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
  206. [    0.457748] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
  207. [    0.457764] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
  208. [    0.457779] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0
  209. [    0.457792] DDR DEBUG: DRV Pull-Up=0x19, DRV Pull-Dwn=0x19
  210. [    0.457802] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2
  211. [    0.457812] DDR DEBUG: Channel b:
  212. [    0.457825] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
  213. [    0.457841] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
  214. [    0.457857] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
  215. [    0.457873] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
  216. [    0.457887] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0
  217. [    0.457899] DDR DEBUG: DRV Pull-Up=0x19, DRV Pull-Dwn=0x19
  218. [    0.457910] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2
  219. [    0.480004] bio: create slab <bio-0> at 0
  220. [    0.480823] SCSI subsystem initialized
  221. [    0.480973] usbcore: registered new interface driver usbfs
  222. [    0.481019] usbcore: registered new interface driver hub
  223. [    0.481101] usbcore: registered new device driver usb
  224. [    0.482478] rockchip_i2c ff650000.i2c: i2c-0: Rockchip I2C adapter
  225. [    0.484665] rockchip_i2c ff140000.i2c: i2c-1: Rockchip I2C adapter
  226. [    0.486171] rockchip_i2c ff660000.i2c: i2c-2: Rockchip I2C adapter
  227. [    0.487155] rockchip_i2c ff150000.i2c: i2c-3: Rockchip I2C adapter
  228. [    0.487394] rockchip_i2c ff160000.i2c: i2c-4: Rockchip I2C adapter
  229. [    0.487871] media: Linux media interface: v0.10
  230. [    0.487913] Linux video capture interface: v2.00
  231. [    0.487967] pps_core: LinuxPPS API ver. 1 registered
  232. [    0.487979] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  233. [    0.488003] PTP clock support registered
  234. [    0.488499] Rockchip ion module is successfully loaded (v1.0)
  235. [    0.488661] Advanced Linux Sound Architecture Driver Initialized.
  236. [    0.489032] Bluetooth: Core ver 2.16
  237. [    0.489071] NET: Registered protocol family 31
  238. [    0.489082] Bluetooth: HCI device and connection manager initialized
  239. [    0.489100] Bluetooth: HCI socket layer initialized
  240. [    0.489115] Bluetooth: L2CAP socket layer initialized
  241. [    0.489141] Bluetooth: SCO socket layer initialized
  242. [    0.489370] cfg80211: Calling CRDA to update world regulatory domain
  243. [    0.490023] act8846_i2c_probe,line=898
  244. [    0.490983] act8846_parse_dt,line=746
  245. [    0.491718] act8846_i2c_probe: act8846_pmic_hold=1
  246. [    0.491740] act8846_i2c_probe: act8846_pmic_sleep=1
  247. [    0.491758] act8846_i2c_probe: act8846_pmic_cpu_det_gpio=1
  248. [    0.491774] act8846_i2c_probe: act8846_pmic_usb_hub_reset_gpio=1
  249. [    0.493599] act_dcdc1: 1200 mV
  250. [    0.496320] vccio: 3300 mV
  251. [    0.498168] vdd_logic: 700 <--> 1500 mV at 1100 mV
  252. [    0.500904] act_dcdc4: 2000 mV
  253. [    0.502132] vccio_sd: 1800 <--> 3300 mV at 3300 mV
  254. [    0.504206] act_ldo2: 1000 mV
  255. [    0.506284] act_ldo3: 3300 mV
  256. [    0.508359] act_ldo4: 3300 mV
  257. [    0.510450] act_ldo5: 3300 mV
  258. [    0.512575] act_ldo6: 1000 mV
  259. [    0.514648] vcc_18: 1800 mV
  260. [    0.516715] act_ldo8: 1800 mV
  261. [    0.521483] vdd_arm: 712 <--> 1500 mV at 1000 mV
  262. [    0.526193] vdd_gpu: 712 <--> 1500 mV at 1000 mV
  263. [    0.526988] Switching to clocksource arch_sys_counter
  264. [    0.546804] rk-fb rockchip-fb: rk fb ion client create success!
  265. [    0.546822] rk-fb rockchip-fb: rockchip framebuffer driver probe
  266. [    0.547212] rk-screen rk_screen.9: rockchip screen probe success
  267. [    0.547464] rk32-lvds rk32-lvds: rk32 lvds driver probe success
  268. [    0.547791] rk32-edp ff970000.edp: screen is not edp!
  269. [    0.547813] rk32-edp: probe of ff970000.edp failed with error -22
  270. [    0.548524] graphics fb0: rockchip framebuffer registerd:fb0
  271. [    0.548844] graphics fb1: rockchip framebuffer registerd:fb1
  272. [    0.549001] graphics fb2: rockchip framebuffer registerd:fb2
  273. [    0.549159] graphics fb3: rockchip framebuffer registerd:fb3
  274. [    0.569511] rk3288-lcdc lcdc0: lcdc0: dclk:78000000>>fps:68
  275. [    0.569536] rk3288-lcdc lcdc0: wakeup from standby!
  276. [    0.585438] alloc_buffer:ion_phy_addr=0x40000000
  277. [    0.588424] rk_battery_charger_detect_cb , battery_charger_detect 1
  278. [    0.593798] fb0:phy:40000000>>vir:f0171000>>len:0xc00000
  279. [    0.597327] rk3288-lcdc lcdc0: lcdc0 probe ok, iommu disabled
  280. [    0.597482] rk3288-lcdc lcdc1: can't find power_ctr node for lcdc1
  281. [    0.597497] rk_fb_trsm_ops_get:un supported transmitter:0!
  282. [    0.597726] graphics fb4: rockchip framebuffer registerd:fb4
  283. [    0.598029] graphics fb5: rockchip framebuffer registerd:fb5
  284. [    0.598188] graphics fb6: rockchip framebuffer registerd:fb6
  285. [    0.598343] graphics fb7: rockchip framebuffer registerd:fb7
  286. [    0.598360] fb0:phy:40000000>>vir:f0171000>>len:0xc00000
  287. [    0.598374] rk3288-lcdc lcdc1: lcdc1 probe ok, iommu disabled
  288. [    0.598954] rockchip_set_mux:warning ignore bank num 15
  289. [    0.599073] rockchip_set_mux:warning ignore bank num 15
  290. [    0.599183] rockchip_set_mux:warning ignore bank num 15
  291. [    0.599291] rockchip_set_mux:warning ignore bank num 15
  292. [    0.599394] rockchip_set_mux:warning ignore bank num 15
  293. [    0.599505] rockchip_set_mux:warning ignore bank num 15
  294. [    0.600063] rockchip_set_mux:warning ignore bank num 15
  295. [    0.600202] rockchip_set_mux:warning ignore bank num 15
  296. [    0.600740] rockchip_set_mux:warning ignore bank num 15
  297. [    0.600882] rockchip_set_mux:warning ignore bank num 15
  298. [    0.601417] rockchip_set_mux:warning ignore bank num 15
  299. [    0.601555] rockchip_set_mux:warning ignore bank num 15
  300. [    0.602104] rockchip_set_mux:warning ignore bank num 15
  301. [    0.602247] rockchip_set_mux:warning ignore bank num 15
  302. [    0.603544] NET: Registered protocol family 2
  303. [    0.603982] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
  304. [    0.604117] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
  305. [    0.604253] TCP: Hash tables configured (established 8192 bind 8192)
  306. [    0.604301] TCP: reno registered
  307. [    0.604318] UDP hash table entries: 512 (order: 2, 16384 bytes)
  308. [    0.604355] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
  309. [    0.604554] NET: Registered protocol family 1
  310. [    0.604732] Unpacking initramfs...
  311. [    0.766538] Freeing initrd memory: 3908K (c4bf0000 - c4fc1000)
  312. [    0.767149] hw perfevents: enabled with ARMv7 Cortex-A12 PMU driver, 7 counters available
  313. [    0.767607] probe device ff9a0000.vpu_service
  314. [    0.767783] vpu_service: power on
  315. [    0.768841] checking hw id 4831
  316. [    0.769229] vpu_service set to auto frequency mode
  317. [    0.769267] vpu_service: power off...
  318. [    0.769306] done
  319. [    0.769315] init success
  320. [    0.769379] probe device ff9c0000.hevc_service
  321. [    0.769573] hevc_service: power on
  322. [    0.770610] checking hw id 6867
  323. [    0.770836] hevc_service: power off...
  324. [    0.770875] done
  325. [    0.770884] init success
  326. [    0.770995] rknandbase v1.0 2014-03-31
  327. [    0.771091] rknand ff400000.nandc0: no irq resource?
  328. [    0.771209] rknand_driver:ret = 0
  329. [    0.772724] audit: initializing netlink socket (disabled)
  330. [    0.772765] type=2000 audit(0.460:1): initialized
  331. [    0.773576] bounce pool size: 64 pages
  332. [    0.777914] fuse init (API version 7.22)
  333. [    0.778255] msgmni has been set to 1450
  334. [    0.779984] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
  335. [    0.780004] io scheduler noop registered
  336. [    0.780015] io scheduler deadline registered
  337. [    0.780105] io scheduler cfq registered (default)
  338. [    0.783632] rga2 ff920000.rga: rga ion client create success!
  339. [    0.783775] rga: Driver loaded succesfully
  340. [    0.784377] IEP Driver loaded succesfully
  341. [    0.784466] Module initialized.
  342. [    0.785332] dma-pl330 ffb20000.pdma: Loaded driver for PL330 DMAC-2364208
  343. [    0.785354] dma-pl330 ffb20000.pdma:         DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10
  344. [    0.786636] dma-pl330 ff250000.pdma: Loaded driver for PL330 DMAC-2364208
  345. [    0.786656] dma-pl330 ff250000.pdma:         DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
  346. [    0.786935] pwm-voltage-regulator pwm_regulator.25: unable to request PWM, trying legacy API
  347. [    0.786954] pwm-voltage-regulator pwm_regulator.25: unable to request legacy PWM
  348. [    0.786967] pwm_regulator_probe:error
  349. [    0.786991] platform pwm_regulator.25: Driver pwm-voltage-regulator requests probe deferral
  350. [    0.787318] rk_serial.c v1.8 2014-03-04
  351. [    0.787524] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 87) is a rk29_serial.0
  352. [    0.787711] serial ff180000.serial: membase f0d94000
  353. [    0.790361] loop: module loaded
  354. [    0.790906] SCSI Media Changer driver v0.25
  355. [    0.791203] tun: Universal TUN/TAP device driver, 1.6
  356. [    0.791218] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  357. [    0.791367] vmac_init.
  358. [    0.791861] stmmac_probe_config_dt: Can not read property: pmu_regulator.
  359. [    0.791878] stmmac_probe_config_dt: Can not read property: pmu_enable_level.
  360. [    0.791892] stmmac_probe_config_dt: clock input or output? (input).
  361. [    0.791905] stmmac_probe_config_dt: TX delay(0x30).
  362. [    0.791916] stmmac_probe_config_dt: RX delay(0x10).
  363. [    0.791963] stmmac_probe_config_dt: is rockchip,rk3288-gmac
  364. [    0.791974] stmmc_pltfr_init:
  365. [    0.791994] stmmc_pltfr_init: init for RGMII
  366. [    0.792006] tx delay=0x30
  367. [    0.792006] rx delay=0x10
  368. [    0.792438] stmmac - user ID: 0x10, Synopsys ID: 0x35
  369. [    0.792450]  Normal descriptors
  370. [    0.792458]  Ring mode enabled
  371. [    0.792468]  DMA HW capability register supported
  372. [    0.792480]  RX Checksum Offload Engine supported (type 2)
  373. [    0.792491]  TX Checksum insertion supported
  374. [    0.792500]  Wake-Up On Lan supported
  375. [    0.792535]  Enable RX Mitigation via HW Watchdog Timer
  376. [    0.792963] PPP generic driver version 2.4.2
  377. [    0.793114] PPP BSD Compression module registered
  378. [    0.793128] PPP Deflate Compression module registered
  379. [    0.793151] PPP MPPE Compression module registered
  380. [    0.793163] NET: Registered protocol family 24
  381. [    0.793196] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
  382. [    0.793210] CSLIP: code copyright 1989 Regents of the University of California.
  383. [    0.793229] Rockchip WiFi SYS interface (V1.00) ...
  384. [    0.793261] esp_mem_init enter date Dec 26 2014 09:48:50
  385. [    0.793303] esp_mem_init complete
  386. [    0.793371] usbcore: registered new interface driver catc
  387. [    0.793411] usbcore: registered new interface driver kaweth
  388. [    0.793424] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
  389. [    0.793463] usbcore: registered new interface driver pegasus
  390. [    0.793503] usbcore: registered new interface driver rtl8150
  391. [    0.793542] usbcore: registered new interface driver r8152
  392. [    0.793553] hso: drivers/net/usb/hso.c: Option Wireless
  393. [    0.793618] usbcore: registered new interface driver hso
  394. [    0.793663] usbcore: registered new interface driver asix
  395. [    0.793701] usbcore: registered new interface driver ax88179_178a
  396. [    0.793739] usbcore: registered new interface driver cdc_ether
  397. [    0.793788] usbcore: registered new interface driver cdc_eem
  398. [    0.793826] usbcore: registered new interface driver dm9601
  399. [    0.793864] usbcore: registered new interface driver dm9620
  400. [    0.793910] usbcore: registered new interface driver smsc75xx
  401. [    0.793956] usbcore: registered new interface driver smsc95xx
  402. [    0.793994] usbcore: registered new interface driver gl620a
  403. [    0.794036] usbcore: registered new interface driver net1080
  404. [    0.794076] usbcore: registered new interface driver plusb
  405. [    0.794115] usbcore: registered new interface driver rndis_host
  406. [    0.794153] usbcore: registered new interface driver cdc_subset
  407. [    0.794190] usbcore: registered new interface driver zaurus
  408. [    0.794230] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
  409. [    0.794286] usbcore: registered new interface driver int51x1
  410. [    0.794325] usbcore: registered new interface driver kalmia
  411. [    0.794368] usbcore: registered new interface driver ipheth
  412. [    0.794410] usbcore: registered new interface driver sierra_net
  413. [    0.794450] usbcore: registered new interface driver cx82310_eth
  414. [    0.794498] usbcore: registered new interface driver cdc_ncm
  415. [    0.794537] usbcore: registered new interface driver qmi_wwan
  416. [    0.794576] usbcore: registered new interface driver cdc_mbim
  417. [    0.794589] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  418. [    0.796972] ehci_rk_probe f0e00000 f0e00010
  419. [    0.796990] rockchip_ehci_host ff500000.usb: Rockchip On-Chip EHCI Host Controller
  420. [    0.797021] rockchip_ehci_host ff500000.usb: new USB bus registered, assigned bus number 1
  421. [    0.797332] rockchip_ehci_host ff500000.usb: irq 56, io mem 0xff500000
  422. [    0.812423] rockchip_ehci_host ff500000.usb: USB 0.0 started, EHCI 1.00
  423. [    0.812497] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
  424. [    0.812515] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  425. [    0.812530] usb usb1: Product: Rockchip On-Chip EHCI Host Controller
  426. [    0.812544] usb usb1: Manufacturer: Linux 3.10.0 ehci_hcd
  427. [    0.812557] usb usb1: SerialNumber: ff500000.usb
  428. [    0.812968] hub 1-0:1.0: USB hub found
  429. [    0.812992] hub 1-0:1.0: 1 port detected
  430. [    0.841930] ehci_rk_probe ok
  431. [    0.842087] usbcore: registered new interface driver cdc_acm
  432. [    0.842101] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
  433. [    0.842156] usbcore: registered new interface driver usblp
  434. [    0.842204] usbcore: registered new interface driver cdc_wdm
  435. [    0.842266] usbcore: registered new interface driver usb-storage
  436. [    0.842308] usbcore: registered new interface driver ums-alauda
  437. [    0.842346] usbcore: registered new interface driver ums-cypress
  438. [    0.842385] usbcore: registered new interface driver ums-datafab
  439. [    0.842421] usbcore: registered new interface driver ums_eneub6250
  440. [    0.842460] usbcore: registered new interface driver ums-freecom
  441. [    0.842498] usbcore: registered new interface driver ums-isd200
  442. [    0.842537] usbcore: registered new interface driver ums-jumpshot
  443. [    0.842580] usbcore: registered new interface driver ums-karma
  444. [    0.842620] usbcore: registered new interface driver ums-onetouch
  445. [    0.842660] usbcore: registered new interface driver ums-sddr09
  446. [    0.842708] usbcore: registered new interface driver ums-sddr55
  447. [    0.842748] usbcore: registered new interface driver ums-usbat
  448. [    0.842830] usbcore: registered new interface driver usbserial
  449. [    0.842868] usbcore: registered new interface driver usbserial_generic
  450. [    0.842899] usbserial: USB Serial support registered for generic
  451. [    0.842941] usbcore: registered new interface driver option
  452. [    0.842971] usbserial: USB Serial support registered for GSM modem (1-port)
  453. [    0.843063] usbcore: registered new interface driver trancevibrator
  454. [    0.843075] usb20_otg: version 3.10a 21-DEC-2012
  455. [    0.843478] f0e80040
  456. [    0.843492] Core Release: 3.10a
  457. [    0.843504] Setting default values for core params
  458. [    0.843618] Using Buffer DMA mode
  459. [    0.843630] Periodic Transfer Interrupt Enhancement - disabled
  460. [    0.843641] Multiprocessor Interrupt Enhancement - disabled
  461. [    0.843654] OTG VER PARAM: 0, OTG VER FLAG: 0
  462. [    0.843664] ^^^^^^^^^^^^^^^^^Device Mode
  463. [    0.843678] Dedicated Tx FIFOs mode
  464. [    0.843695] pcd_init otg_dev = ed6a7640
  465. [    0.843830] usb20_otg ff580000.usb: DWC OTG Controller
  466. [    0.843857] usb20_otg ff580000.usb: new USB bus registered, assigned bus number 2
  467. [    0.843887] usb20_otg ff580000.usb: irq 55, io mem 0x00000000
  468. [    0.843940] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
  469. [    0.843956] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  470. [    0.843971] usb usb2: Product: DWC OTG Controller
  471. [    0.843991] usb usb2: Manufacturer: Linux 3.10.0 dwc_otg_hcd
  472. [    0.844005] usb usb2: SerialNumber: ff580000.usb
  473. [    0.844365] hub 2-0:1.0: USB hub found
  474. [    0.844388] hub 2-0:1.0: 1 port detected
  475. [    0.844685] usb20_host: version 3.10a 21-DEC-2012
  476. [    0.847146] f0f00040
  477. [    0.847159] Core Release: 3.10a
  478. [    0.847170] Setting default values for core params
  479. [    0.847263] Using Buffer DMA mode
  480. [    0.847275] Periodic Transfer Interrupt Enhancement - disabled
  481. [    0.847286] Multiprocessor Interrupt Enhancement - disabled
  482. [    0.847298] OTG VER PARAM: 0, OTG VER FLAG: 0
  483. [    0.847308] ^^^^^^^^^^^^^^^^^^Host Mode
  484. [    0.847336] usb20_host ff540000.usb: DWC OTG Controller
  485. [    0.847362] usb20_host ff540000.usb: new USB bus registered, assigned bus number 3
  486. [    0.847390] usb20_host ff540000.usb: irq 57, io mem 0x00000000
  487. [    0.847482] Init: Power Port (0)
  488. [    0.847536] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
  489. [    0.847552] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  490. [    0.847567] usb usb3: Product: DWC OTG Controller
  491. [    0.847579] usb usb3: Manufacturer: Linux 3.10.0 dwc_otg_hcd
  492. [    0.847592] usb usb3: SerialNumber: ff540000.usb
  493. [    0.847947] hub 3-0:1.0: USB hub found
  494. [    0.847969] hub 3-0:1.0: 1 port detected
  495. [    0.848473] .. rk pwm remotectl v1.0 init
  496. [    0.848555] remotectl probe j=0x0
  497. [    0.848699] input: ff680000.pwm as /devices/ff680000.pwm/input/input0
  498. [    0.848873] pwm enable val=0x646205
  499. [    0.849131] usbcore: registered new interface driver xpad
  500. [    0.849184] usbcore: registered new interface driver usb_acecad
  501. [    0.849228] usbcore: registered new interface driver aiptek
  502. [    0.849272] usbcore: registered new interface driver gtco
  503. [    0.849316] usbcore: registered new interface driver hanwang
  504. [    0.849359] usbcore: registered new interface driver kbtab
  505. [    0.849413] usbcore: registered new interface driver wacom
  506. [    0.849424] ==gsl_ts_init==
  507. [    0.849494] GSLX680 Enter gsl_ts_probe
  508. [    0.849505] ==kzalloc success=
  509. [    0.849515] gsl_ts_probe-1292
  510. [    0.849553] gslX680 1-0041: reset pin invalid
  511. [    0.849564] [GSLX680] Enter gslX680_ts_init
  512. [    0.849784] input: gslX680 as /devices/ff140000.i2c/i2c-1/1-0041/input/input1
  513. [    0.849909] gsl_ts_probe-1318
  514. [    0.849921] org chip_type=36
  515. [    0.901668] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  516. [    0.940381] dwc_otg_hcd_suspend, usb device mode
  517. [    0.960689] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  518. [    0.960703] chip_type=88, reg=0
  519. [    1.019045] test_i2c-394: Enter
  520. [    1.019729] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  521. [    1.059079] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  522. [    1.059093] test_i2c-413: Exit
  523. [    1.059102] ------gslX680 test_i2c error------
  524. [    1.098436] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  525. [    1.098450] #########check mem read 0xb0 = 0 0 0 0 #########
  526. [    1.156804] test_i2c-394: Enter
  527. [    1.157485] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  528. [    1.196833] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  529. [    1.196846] test_i2c-413: Exit
  530. [    1.196855] ------gslX680 test_i2c error------
  531. [    1.197028] gsl_ts_probe () : queue gsl_monitor_workqueue
  532. [    1.197109] [GSLX680] End gsl_ts_probe
  533. [    1.197178] ret=0
  534. [    1.202053] rtc_hym8563 0-0051: rtc core: registered hym8563 as rtc0
  535. [    1.202117] i2c /dev entries driver
  536. [    1.202793] IR NEC protocol handler initialized
  537. [    1.202807] IR RC5(x) protocol handler initialized
  538. [    1.202817] IR RC6 protocol handler initialized
  539. [    1.202827] IR JVC protocol handler initialized
  540. [    1.202836] IR Sony protocol handler initialized
  541. [    1.202846] IR RC5 (streamzap) protocol handler initialized
  542. [    1.202857] IR SANYO protocol handler initialized
  543. [    1.202867] IR MCE Keyboard/mouse protocol handler initialized
  544. [    1.203009] usbcore: registered new interface driver uvcvideo
  545. [    1.203022] USB Video Class driver (1.1.1)
  546. [    1.203034] CamSys driver version: v0.23.0,  CamSys head file version: v0.9.0
  547. [    1.204405] D1:camsys_platform_probe(1067): 1-gpios-cifpower??? gpio=236
  548. [    1.204429] D1:camsys_platform_probe(1070): gpios-cifpower??? gpio_request
  549. [    1.204449] D1:camsys_platform_probe(1072): 1-gpios-cifpower??? gpio_request=0
  550. [    1.204469] D1:camsys_platform_probe(1079): gpios-cifpower??? 236 high
  551. [    1.204553] D1:camsys_mipiphy_probe_cb(163): ff910000.isp mipi phy0 probe success(reg_phy: 0x0  reg_vir: 0x0  size: 0x0)
  552. [    1.204693] D1:camsys_mipiphy_probe_cb(160): ff910000.isp mipi phy1 probe success(reg_phy: 0xff968000  reg_vir: 0xf0da8000  size: 0x        4000)
  553. [    1.205328] D1:camsys_platform_probe(1183): ff910000.isp memory:
  554. [    1.205346] D1:camsys_platform_probe(1193):     Register memory (phy: 0xff910000 vir: 0xf0de0000 size: 0x10000)
  555. [    1.205363] D1:camsys_platform_probe(1188):     I2c memory (phy: 0x2d6af000 vir: 0xed6af000 size: 0x1000)
  556. [    1.205377] D1:camsys_platform_probe(1208): Probe ff910000.isp device success
  557. [    1.206612] rockchip_temp_probe,line=362
  558. [    1.265052] tsadc ff280000.tsadc: initialized
  559. [    1.265432] device-mapper: uevent: version 1.0.3
  560. [    1.265686] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
  561. [    1.265983] Bluetooth: HCI UART driver ver 2.2
  562. [    1.265998] Bluetooth: HCI H4 protocol initialized
  563. [    1.266009] Bluetooth: HCILL protocol initialized
  564. [    1.269089] cpufreq version 1.0, suspend freq 1200 MHz
  565. [    1.269270] cpuidle: using governor ladder
  566. [    1.269283] cpuidle: using governor menu
  567. [    1.269319] Synopsys Designware Multimedia Card Interface Driver
  568. [    1.269555] dwmmc_rockchip ff0f0000.rksdmmc: Version ID is 270a
  569. [    1.269822] dwmmc_rockchip ff0f0000.rksdmmc: Using internal DMA controller.
  570. [    1.269987] 3379..dw_mci_init_slot: fmin=400000, fmax=100000000 [mmc0]
  571. [    1.270001] mmc0 : Rockchip specific MHSC: Ver 1.13 2014-09-05
  572. [    1.270113] 1390..dw_mci_set_ios:  no card. [mmc0]
  573. [    1.284736] 1390..dw_mci_set_ios:  no card. [mmc0]
  574. [    1.304446] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out 800000Hz for init[mmc0]
  575. [    1.304496] dwmmc_rockchip ff0f0000.rksdmmc: DW MMC controller at irq 67, 32 bit host data width, 256 deep fifo
  576. [    1.304515] dwmmc_rockchip ff0f0000.rksdmmc: 1 slots initialized
  577. [    1.304788] dwmmc_rockchip ff0c0000.rksdmmc: Version ID is 270a
  578. [    1.305619] dwmmc_rockchip ff0c0000.rksdmmc: Using internal DMA controller.
  579. [    1.305843] 3379..dw_mci_init_slot: fmin=400000, fmax=50000000 [mmc1]
  580. [    1.305868] mmc1 : Rockchip specific MHSC: Ver 1.13 2014-09-05
  581. [    1.305927] mmc1: no vmmc regulator found
  582. [    1.306023] dwmmc_rockchip ff0c0000.rksdmmc: mmc1: No udbg pinctrl found!
  583. [    1.306086] 1390..dw_mci_set_ios:  no card. [mmc1]
  584. [    1.324092] 1390..dw_mci_set_ios:  no card. [mmc1]
  585. [    1.336560] mmc0: BKOPS_EN bit is not set
  586. [    1.338441] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 52000000Hz, actual 50000000HZ div = 1)
  587. [    1.338465] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out normal clock [mmc0]
  588. [    1.338515] rk_sdmmc: BOOT Bus speed=50000000Hz,Bus width=8bits.[mmc0]
  589. [    1.338608] mmc0: new high speed MMC card at address 0001
  590. [    1.338832] mmcblk0: mmc0:0001 AWMB3R 14.5 GiB
  591. [    1.339096]  parameter: 0x000000000 -- 0x000400000 (4 MB)
  592. [    1.339108]      uboot: 0x000400000 -- 0x000800000 (4 MB)
  593. [    1.339117]       misc: 0x000800000 -- 0x000c00000 (4 MB)
  594. [    1.339125]   resource: 0x000c00000 -- 0x001c00000 (16 MB)
  595. [    1.339134]     kernel: 0x001c00000 -- 0x002c00000 (16 MB)
  596. [    1.339142]       boot: 0x002c00000 -- 0x004c00000 (32 MB)
  597. [    1.339151]   recovery: 0x004c00000 -- 0x006c00000 (32 MB)
  598. [    1.339159]     backup: 0x006c00000 -- 0x00a000000 (52 MB)
  599. [    1.339168]      cache: 0x00a000000 -- 0x012000000 (128 MB)
  600. [    1.339177]     kpanic: 0x012000000 -- 0x012400000 (4 MB)
  601. [    1.339185]     system: 0x012400000 -- 0x042400000 (768 MB)
  602. [    1.339193]   metadata: 0x042400000 -- 0x042800000 (4 MB)
  603. [    1.339202]   userdata: 0x042800000 -- 0x082800000 (1024 MB)
  604. [    1.339210] radical_update: 0x082800000 -- 0x086800000 (64 MB)
  605. [    1.339219]       user: 0x086800000 -- 0x3a3a00000 (12754 MB)
  606. [    1.339243]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p151390..dw_mci_set_ios:  no card. [mmc1]
  607. [    1.343814] dwmmc_rockchip ff0c0000.rksdmmc: DW MMC controller at irq 64, 32 bit host data width, 256 deep fifo
  608. [    1.343826] dwmmc_rockchip ff0c0000.rksdmmc: 1 slots initialized
  609. [    1.344087] dwmmc_rockchip ff0d0000.rksdmmc: Version ID is 270a
  610. [    1.344268] dwmmc_rockchip ff0d0000.rksdmmc: Using internal DMA controller.
  611. [    1.344372] 3379..dw_mci_init_slot: fmin=200000, fmax=50000000 [mmc2]
  612. [    1.344382] mmc2 : Rockchip specific MHSC: Ver 1.13 2014-09-05
  613. [    1.344629] 1390..dw_mci_set_ios:  no card. [mmc2]
  614. [    1.363451] 1390..dw_mci_set_ios:  no card. [mmc2]
  615. [    1.383134] 1390..dw_mci_set_ios:  no card. [mmc2]
  616. [    1.383165] dwmmc_rockchip ff0d0000.rksdmmc: DW MMC controller at irq 65, 32 bit host data width, 256 deep fifo
  617. [    1.383178] dwmmc_rockchip ff0d0000.rksdmmc: 1 slots initialized
  618. [    1.383397] leds-gpio leds.34: pins are not configured from the driver
  619. [    1.383600] hidraw: raw HID events driver (C) Jiri Kosina
  620. [    1.384950] usbcore: registered new interface driver usbhid
  621. [    1.384959] usbhid: USB HID core driver
  622. [    1.385222] zram: Created 1 device(s) ...
  623. [    1.385511] ashmem: initialized
  624. [    1.385610] logger: created 256K log 'log_main'
  625. [    1.385704] logger: created 256K log 'log_events'
  626. [    1.385792] logger: created 256K log 'log_radio'
  627. [    1.385880] logger: created 256K log 'log_system'
  628. [    1.386859] input: rk29-keypad as /devices/ff100000.adc/key.36/input/input2
  629. [    1.387630] es8323 probe i2c recv ok
  630. [    1.387703] i2c-core: driver [ES8323] using legacy suspend method
  631. [    1.387712] i2c-core: driver [ES8323] using legacy resume method
  632. [    1.388461] rockchip-hdmi-spdif rockchip-hdmi-spdif.29: ASoC: CPU DAI (null) not registered
  633. [    1.388489] rockchip_hdmi_spdif_audio_probe() register card failed:-517
  634. [    1.388506] platform rockchip-hdmi-spdif.29: Driver rockchip-hdmi-spdif requests probe deferral
  635. [    1.388731] es8323_probe
  636. [    2.023090] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> NULL --> Left Line Mux
  637. [    2.023103] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> NULL -> Left Line Mux
  638. [    2.023113] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> NULL --> Left Line Mux
  639. [    2.023121] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> NULL -> Left Line Mux
  640. [    2.023131] ES8323 2-0010: ASoC: no dapm match for Left PGA Mux --> NULL --> Left Line Mux
  641. [    2.023139] ES8323 2-0010: ASoC: Failed to add route Left PGA Mux -> NULL -> Left Line Mux
  642. [    2.023148] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> NULL --> Right Line Mux
  643. [    2.023156] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> NULL -> Right Line Mux
  644. [    2.023165] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> NULL --> Right Line Mux
  645. [    2.023173] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> NULL -> Right Line Mux
  646. [    2.023182] ES8323 2-0010: ASoC: no dapm match for Right PGA Mux --> NULL --> Right Line Mux
  647. [    2.023190] ES8323 2-0010: ASoC: Failed to add route Right PGA Mux -> NULL -> Right Line Mux
  648. [    2.023199] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> LAMP --> Left PGA Mux
  649. [    2.023207] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> LAMP -> Left PGA Mux
  650. [    2.023216] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> LAMP --> Left PGA Mux
  651. [    2.023223] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> LAMP -> Left PGA Mux
  652. [    2.023232] ES8323 2-0010: ASoC: no dapm match for Differential Mux --> LAMP --> Left PGA Mux
  653. [    2.023240] ES8323 2-0010: ASoC: Failed to add route Differential Mux -> LAMP -> Left PGA Mux
  654. [    2.023249] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> RAMP --> Right PGA Mux
  655. [    2.023256] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> RAMP -> Right PGA Mux
  656. [    2.023265] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> RAMP --> Right PGA Mux
  657. [    2.023273] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> RAMP -> Right PGA Mux
  658. [    2.023282] ES8323 2-0010: ASoC: no dapm match for Differential Mux --> RAMP --> Right PGA Mux
  659. [    2.023289] ES8323 2-0010: ASoC: Failed to add route Differential Mux -> RAMP -> Right PGA Mux
  660. [    2.023298] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> LAMP --> Differential Mux
  661. [    2.023306] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> LAMP -> Differential Mux
  662. [    2.023315] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> RAMP --> Differential Mux
  663. [    2.023322] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> RAMP -> Differential Mux
  664. [    2.023331] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> LAMP --> Differential Mux
  665. [    2.023338] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> LAMP -> Differential Mux
  666. [    2.023347] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> RAMP --> Differential Mux
  667. [    2.023354] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> RAMP -> Differential Mux
  668. [    2.023374] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> LAMP --> Left Line Mux
  669. [    2.023381] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> LAMP -> Left Line Mux
  670. [    2.023390] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> LAMP --> Left Line Mux
  671. [    2.023398] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> LAMP -> Left Line Mux
  672. [    2.023406] ES8323 2-0010: ASoC: no dapm match for Left PGA Mux --> LAMP --> Left Line Mux
  673. [    2.023414] ES8323 2-0010: ASoC: Failed to add route Left PGA Mux -> LAMP -> Left Line Mux
  674. [    2.023423] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> RAMP --> Right Line Mux
  675. [    2.023430] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> RAMP -> Right Line Mux
  676. [    2.023439] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> RAMP --> Right Line Mux
  677. [    2.023447] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> RAMP -> Right Line Mux
  678. [    2.023455] ES8323 2-0010: ASoC: no dapm match for Right PGA Mux --> RAMP --> Right Line Mux
  679. [    2.023463] ES8323 2-0010: ASoC: Failed to add route Right PGA Mux -> RAMP -> Right Line Mux
  680. [    2.023571] ES8323 2-0010: ASoC: mux Right Line Mux has no paths
  681. [    2.023583] ES8323 2-0010: ASoC: mux Left Line Mux has no paths
  682. [    2.023592] ES8323 2-0010: ASoC: mux Right PGA Mux has no paths
  683. [    2.023604] ES8323 2-0010: ASoC: mux Left PGA Mux has no paths
  684. [    2.023623] ES8323 2-0010: ASoC: mux Differential Mux has no paths
  685. [    2.026889] rockchip-es8323 rockchip-es8323.31:  ES8323 HiFi <-> rockchip-i2s.0 mapping ok
  686. [    2.027208] input: RK_ES8323 Headphone Jack as /devices/rockchip-es8323.31/sound/card0/input3
  687. [    2.027851] rockchip-hdmi-i2s rockchip-hdmi-i2s.28:  rk-hdmi-i2s-hifi <-> rockchip-i2s.0 mapping ok
  688. [    2.028146] u32 classifier
  689. [    2.028153]     Actions configured
  690. [    2.028162] Netfilter messages via NETLINK v0.30.
  691. [    2.028208] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
  692. [    2.028452] ctnetlink v0.93: registering with nfnetlink.
  693. [    2.028506] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
  694. [    2.028513] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
  695. [    2.028709] xt_time: kernel timezone is -0000
  696. [    2.028866] ip_tables: (C) 2000-2006 Netfilter Core Team
  697. [    2.028965] arp_tables: (C) 2002 David S. Miller
  698. [    2.028995] TCP: cubic registered
  699. [    2.029001] Initializing XFRM netlink socket
  700. [    2.029166] NET: Registered protocol family 10
  701. [    2.029560] mip6: Mobile IPv6
  702. [    2.029583] ip6_tables: (C) 2000-2006 Netfilter Core Team
  703. [    2.029671] sit: IPv6 over IPv4 tunneling driver
  704. [    2.029925] NET: Registered protocol family 17
  705. [    2.029946] NET: Registered protocol family 15
  706. [    2.029986] Bridge firewalling registered
  707. [    2.029996] Ebtables v2.0 registered
  708. [    2.030118] Bluetooth: RFCOMM TTY layer initialized
  709. [    2.030138] Bluetooth: RFCOMM socket layer initialized
  710. [    2.030144] Bluetooth: RFCOMM ver 1.11
  711. [    2.030150] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
  712. [    2.030155] Bluetooth: BNEP filters: protocol multicast
  713. [    2.030164] Bluetooth: BNEP socket layer initialized
  714. [    2.030170] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  715. [    2.030179] Bluetooth: HIDP socket layer initialized
  716. [    2.030199] l2tp_core: L2TP core driver, V2.0
  717. [    2.030210] l2tp_ppp: PPPoL2TP kernel driver, V2.0
  718. [    2.030217] [WLAN_RFKILL]: Enter rfkill_wlan_init
  719. [    2.030356] [WLAN_RFKILL]: Enter rfkill_wlan_probe
  720. [    2.030364] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = bcmwifi
  721. [    2.030372] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
  722. [    2.030379] [WLAN_RFKILL]: wlan_platdata_parse_dt: disable wifi io reference voltage control.
  723. [    2.030386] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
  724. [    2.030403] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,poweren_gpio = 156, flags = 0.
  725. [    2.030420] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 158, flags = 0.
  726. [    2.030428] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
  727. [    2.030448] [WLAN_RFKILL]: rockchip_wifi_voltage_select: wifi & sdio reference voltage: 1.8V
  728. [    2.030488] [WLAN_RFKILL]: Exit rfkill_wlan_probe
  729. [    2.030523] [BT_RFKILL]: Enter rfkill_rk_init
  730. [    2.030627] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 147.
  731. [    2.030641] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,power_gpio = 155.
  732. [    2.030653] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 157.
  733. [    2.030665] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 154.
  734. [    2.030677] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 159.
  735. [    2.030713] [BT_RFKILL]: Request irq for bt wakeup host
  736. [    2.030782] [BT_RFKILL]: ** disable irq
  737. [    2.030848] [BT_RFKILL]: ap6335 device registered.
  738. [    2.031640] rk3288-hdmi ff980000.hdmi: rk3288 hdmi probe sucess.
  739. [    2.032315] VFP support v0.3: implementor 41 architecture 3 part 30 variant d rev 0
  740. [    2.032331] rk3288_init_suspend
  741. [    2.032338] rk3288_suspend_init enter
  742. [    2.032449] rk3288_suspend_init: pm_ctrbits =200007
  743. [    2.032474] gpio_get_dts_info suspend:4
  744. [    2.032480] gpio_get_dts_info resume:4
  745. [    2.032485] rockchip,pmic-suspend_gpios:14007a10 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  746. [    2.032510] rockchip,pmic-resume_gpios:2007a11 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
  747. [    2.032658] clks_gating_suspend_init:clkgt info ok
  748. [    2.032737] Registering SWP/SWPB emulation handler
  749. [    2.033013] ddrfreq: verion 1.2 20140526
  750. [    2.033022] ddrfreq: normal 396MHz video_1080p 240MHz video_4k 396MHz dualview 396MHz idle 0MHz suspend 200MHz reboot 396MHz
  751. [    2.033030] ddrfreq: auto-freq=0
  752. [    2.033035] ddrfreq: auto-freq-table[0] 240MHz
  753. [    2.033040] ddrfreq: auto-freq-table[1] 324MHz
  754. [    2.033046] ddrfreq: auto-freq-table[2] 396MHz
  755. [    2.033051] ddrfreq: auto-freq-table[3] 528MHz
  756. [    2.047460] regulator-dummy: disabling
  757. [    2.047802] rockchip-hdmi-spdif rockchip-hdmi-spdif.29: ASoC: CPU DAI (null) not registered
  758. [    2.047825] rockchip_hdmi_spdif_audio_probe() register card failed:-517
  759. [    2.047840] platform rockchip-hdmi-spdif.29: Driver rockchip-hdmi-spdif requests probe deferral
  760. [    2.047934] pcd_pullup, is_on 0
  761. [    2.047968] file system registered
  762. [    2.048470] android_usb gadget: Mass Storage Function, version: 2009/09/11
  763. [    2.048479] android_usb gadget: Number of LUNs=2
  764. [    2.048485]  lun0: LUN: removable file: (no medium)
  765. [    2.048492]  lun1: LUN: removable file: (no medium)
  766. [    2.048604] android_usb gadget: android_usb ready
  767. [    2.049139] rtc_hym8563 0-0051: setting system clock to 2011-01-01 12:14:02 UTC (1293884042)
  768. [    2.053680] rk_spdif:rk_spdif_init
  769. [    2.053839] rk_spdif:Entered spdif_probe
  770. [    2.054015] rk_spdif:spdif:spdif probe ok!
  771. [    2.054485] usbcore: registered new interface driver snd-usb-audio
  772. [    2.054501] ALSA device list:
  773. [    2.054506]   #0: RK_ES8323
  774. [    2.054511]   #1: RK-HDMI-I2S
  775. [    2.054734] rockchip-hdmi-spdif rockchip-hdmi-spdif.29:  rk-hdmi-spdif-hifi <-> rockchip-spdif mapping ok
  776. [    2.054839] Freeing unused kernel memory: 592K (c0af1000 - c0b85000)
  777. [    2.059355] SELinux:  Permission attach_queue in class tun_socket not defined in policy.
  778. [    2.059367] SELinux: the above unknown classes and permissions will be denied
  779. [    2.271735] type=1403 audit(1293884042.720:2): policy loaded auid=4294967295 ses=4294967295
  780. [    2.271837] SELinux: Loaded policy from /sepolicy
  781. [    2.273284] type=1404 audit(1293884042.720:3): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
  782. [    2.672234] rk3288-hdmi ff980000.hdmi: Removed.
  783. [    2.672246] hdmi connect to lcdc1
  784. [    2.672489] rk3288-lcdc lcdc1: lcdc1: dclk:74250000>>fps:60
  785. [    2.672499] rk3288-lcdc lcdc1: wakeup from standby!
  786. [    2.672509] rk3288-lcdc lcdc1: lcdc1: dclk:74250000>>fps:60
  787. [    2.819756] dwc_otg_hcd_enable, enable host controller
  788. [    2.942763] Using Buffer DMA mode
  789. [    2.942770] Periodic Transfer Interrupt Enhancement - disabled
  790. [    2.942776] Multiprocessor Interrupt Enhancement - disabled
  791. [    2.942782] OTG VER PARAM: 0, OTG VER FLAG: 0
  792. [    2.942788] ^^^^^^^^^^^^^^^^^^Host Mode
  793. [    2.987139] Init: Power Port (0)
  794. [    2.987175] ff540000.usb resume, HPRT0:0x21401
  795. [    3.124850] Indeed it is in host mode hprt0 = 00021501
  796. [    3.301960] usb 3-1: new high-speed USB device number 2 using usb20_host
  797. [    3.302035] Indeed it is in host mode hprt0 = 00001101
  798. [    3.498952] usb 3-1: New USB device found, idVendor=1a40, idProduct=0101
  799. [    3.498966] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
  800. [    3.498974] usb 3-1: Product: USB 2.0 Hub [MTT]
  801. [    3.499321] hub 3-1:1.0: USB hub found
  802. [    3.499378] hub 3-1:1.0: 4 ports detected
  803. [    3.616838] ff540000.usb suspend, HPRT0:0x1485
  804. [    3.711710] init: /dev/hw_random not found
  805. [    3.712872] type=1400 audit(1293884044.180:4): avc:  denied  { mount } for  pid=1 comm="init" name="/" dev="functionfs" ino=3138 sco        ntext=u:r:kernel:s0 tcontext=u:object_r:unlabeled:s0 tclass=filesystem permissive=1
  806. [    3.712956] android_usb: already disabled
  807. [    3.713077] init: property 'ro.serialno' doesn't exist while expanding '${ro.serialno}'
  808. [    3.713088] init: cannot expand '${ro.serialno}' while writing to '/sys/class/android_usb/android0/iSerial'
  809. [    3.713173] drmboot: module license 'unspecified' taints kernel.
  810. [    3.713181] Disabling lock debugging due to kernel taint
  811. [    3.714251] %s: ok, 20130810
  812. [    8.185776] init: /sbin/e2fsck terminated by exit(8)
  813. [    8.185803] init: Operational error while checking volume '/dev/block/p
  814. __bim/ec_opbn-nzda/ca co'
  815. n't  8.18any6] data: Fenllooto g fnt loca/blme!/plabiorm/_opc/btzdate/ccoue, 't mand t t tzxt4a when[  oki.18for1] Tni
  816.                                                                                                                       __/denicw_ren_om         rStertingirecoveyy /d Sa/pran rty12:1no:8 2pen poriistles
  817.                                            [
  818. m.18ne=4] solroid_FIQ: andrady oisahard
  819. re=  80board9] drot: ootnconepre=ttedIQ0ntax f.apspes_ayin= prnitrtynito.ptdpurtsman29xctund:0x0use200namx00instea(pa[  ete.18054000ini        0@0usi002000(ecatt),synt00200r sx00ify000 prsper0x0'ro800oduct.006el'(rese $cnam0x0ins800d
  820. p[  x00.180008] ini500procacty ,0x000ria00@' d009n000exianiwhi0x0exp0ndi@0x'$r920erialntem{na036 in(baad
  821.                                                                                           [ x008.1000@0x in120 camettdatpan0x0$ro000ria        4340008.1er)10]oraad eesc=emtorloa[    8mes092p=2rea-11-27ngs:44    an1ro955ootcd_rialup=100_on000
  822.                                                                                                   00019D androidboot.mode=emmc

  824. cmdline=console=ttyFIQ0 androidboot.hardware=rk30board androidboot.console=ttyFIQ0 board.ap_has_alsa=0 init=/init  mtdparts=rk29xxnand:        0x00002000@0x00000000(parameter),0x00002000@0x00002000(uboot),0x00002000@0x00004000(misc),0x00008000@0x00006000(resource),0x00008000@0x        0000e000(kernel),0x00010000@0x00016000(boot),0x00010000@0x00026000(recovery),0x0001a000@0x00036000(backup),0x00040000@0x00050000(cache)        ,0x00002000@0x00090000(kpanic),0x00180000@0x00092000(system),0x00002000@0x00212000(metadata),0x00200000@0x00214000(userdata),0x00020000        @0x00414000(radical_update),-@0x00434000(user) storagemedia=emmc loader.timestamp=2014-11-27_16:44:27 androidboot.serialno=100612000000        019D androidboot.mode=emmc

  826. bootmode = emmc
  827. recovery filesystem table
  828. =========================
  829.   0 /mnt/internal_sd vfat /dev/block/platform/ff0f0000.rksdmmc/by-name/user 0
  830.   1 /mnt/external_sd vfat /dev/block/mmcblk1p1 0
  831.   2 /system ext4 /dev/block/platform/ff0f0000.rksdmmc/by-name/system 0
  832.   3 /cache ext4 /dev/block/platform/ff0f0000.rksdmmc/by-name/cache 0
  833.   4 /metadata ext4 /dev/block/platform/ff0f0000.rksdmmc/by-name/metadata 0
  834.   5 /data ext4 /dev/block/platform/ff0f0000.rksdmmc/by-name/userdata 0
  835.   6 /cust ext4 /dev/block/platform/ff0f0000.rksdmmc/by-name/cust 0
  836.   7 /custom ext4 /dev/block/platform/ff0f0000.rksdmmc/by-name/custom 0
  837.   8 /radical_update ext4 /dev/block/platform/ff0f0000.rksdmmc/by-name/radical_update 0
  838.   9 /misc emmc /dev/block/platform/ff0f0000.rksdmmc/by-name/misc 0
  839.   10 /uboot emmc /dev/block/platform/ff0f0000.rksdmmc/by-name/uboot 0
  840.   11 /charge emmc /dev/block/platform/ff0f0000.rksdmmc/by-name/charge 0
  841.   12 /resource emmc /dev/block/platform/ff0f0000.rksdmmc/by-name/resource 0
  842.   13 /parameter emmc /dev/block/platform/ff0f0000.rksdmmc/by-name/parameter 0
  843.   14 /boot emmc /dev/block/platform/ff0f0000.rksdmmc/by-name/boot 0
  844.   15 /recovery emmc /dev/block/platform/ff0f0000.rksdmmc/by-name/recovery 0
  845.   16 /backup emmc /dev/block/platform/ff0f0000.rksdmmc/by-name/backup 0
  846.   17 /tmp ramdisk ramdisk 0

  848. I/ [File] : bootable/recovery/recovery.cpp; [Line] : 1553; [Func] : void SetSdcardRootPath(); InternalSD_ROOT: /mnt/internal_sd
  849. I/ [File] : bootable/recovery/recovery.cpp; [Line] : 1555; [Func] : void SetSdcardRootPath(); ExternalSD_ROOT: /mnt/external_sd
  850. failed to create /cache dir,err=File exists!
  851. [    8.490736] EXT4-fs (mmcblk0p9): recovery complete
  852. failed to read font: res=-1
  853. can't open /dev/tty0: No such file or directory
  854. framebuffer: fd 7 (1280 x 800)
  855. [    8.491283] EXT4-fs (mmcblk0p9): mounted filesystem with ordered data mode. Opts:
  856. [    8.499457] I'am in gsl_ts_suspend() start
  857. [    8.499463] gsl_ts_suspend () : cancel gsl_monitor_work
  858. [    8.536847] hdmi remove from lcdc1
  859. [    8.536857] rk3288-lcdc lcdc1: no layer is used,go to standby!
  860. [    8.562559] rk3288-hdmi ff980000.hdmi: Removed.
  861. [    8.588392] rk3288-lcdc lcdc0: blank mode:4
  862. [    8.633254] rk3288-lcdc lcdc0: blank mode:0
  863. [    8.633266] I'am in gsl_ts_resume() start
  864. [    8.723767] ----------3680A---------
  865. [    8.733612] ***************vbus detect*****************
  866. [    8.783459] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  867. [    8.783 inst####n####xt:   mem r @d1896)
  868. 0 0 0 0 #########
  869. [    8.841842] test_i2c-394: Enter
  870. [      8424  ergsl_ts_rea:  (1 xa1 @ 1dress fail! ret=-11-0xfffffff5
  871. test_i2c-413: Exit_ts_read set data address fail!   no-11-0xfffffff:  (1   8.881599)
  872. [    8.881855] - ----gs      test_i2c :  (r-----@
  873. [99) 8.881869] gsl_ts_resume () : queue gsl_monitor_work
  874. [    8.912859] Using Buffer DMA mode
  875. [    8.912873] Periodic Transfer Interrupt Enhancement - disabled
  876. [    8.912881] Multiprocessor Interrupt Enhancement - disabled
  877. [    8.912890] OTG VER PARAM: 0, OTG VER FLAG: 0
  878. [    8.912897] ^^^^^^^^^^^^^^^^^Device Mode
  879. [    8.912939] *******************soft connect!!!*******************
  880. [    9.032608] USB RESET
  881. Recovery system v4.4.2

  883. [    9.090084] android_work: sent uevent USB_STATE=CONNECTED
  884. Recovery system v4.4.2
  885. in get_args
  886. I/ [File] : bootable/recovery/recovery.cpp; [Line] : 760; [Func] : bool get_args(int*, char***, bool*); Boot command: boot-recovery
  887. I/ [File] : bootable/recovery/recovery.cpp; [Line] : 779; [Func] : bool get_args(int*, char***, bool*); Got arguments from boot message
  888. list arg=2:
  889. recovery
  890. --wipe_all
  891. bootmode = emmc
  892. ro.rk.cpu=rk3288v1
  893. ro.rk.soc=rk3288
  894. ro.rk.bt_enable=true
  895. ro.rk.systembar.tabletUI=false
  896. ro.rk.systembar.voiceicon=true
  897. ro.rk.MassStorage=false
  898. ro.rk.cpu_min_freq=126000

  900. ro.rk.homepage_base=http://www.google.com/webhp?client={CID}&source=android-home
  901. ro.rk.def_brightness=200
  902. ro.rk.screenoff_time=60000
  903. ro.rk.screenshot_enable=true
  904. ro.rk.LowBatteryBrightness=true
  905. ro.rk.install_non_market_apps=false
  906. ro.sf.hwrotation=0
  907. ro.sf.lcd_density=160
  908. ro.sf.fakerotation=false
  909. ro.adb.secure=0
  910. ro.com.google.gmsversion=4.4_r4
  911. ro.com.android.dateformat=MM-dd-yyyy
  912. ro.com.android.dataroaming=true
  913. ro.ril.ecclist=112,911
  914. ro.sms.capable=false
  915. ro.boot.mode=emmc
  916. ro.boot.console=ttyFIQ0
  917. ro.boot.hardware=rk30board
  918. ro.boot.serialno=100612000000019D
  919. ro.hwui.path_cache_size=16
  920. ro.hwui.layer_cache_size=48
  921. ro.hwui.shape_cache_size=4
  922. ro.hwui.texture_cache_size=72
  923. ro.hwui.disable_scissor_opt=true
  924. ro.hwui.gradient_cache_size=1
  925. ro.hwu998] U_shaESE_
  926. [    ize=6
  927. 8o.hwdroidxt_lagge_cachhigh-th=2d 8onrog #1i.tndroida
  928. _ro.k:usentxt_veng USachTAheiCON=1024                [ l  9ach552idtand024
  929. ro.hwui.text_small_cache_height=1024
  930. ro.wifi.channels=
  931. ro.allow.mock.location=1
  932. ro.audio.monitorOrientation=true
  933. ro.board.platform=rk3288
  934. ro.build.id=KTU84Q
  935. ro.build.date=2014?1′ 12??? 30?—￥ ???????o? 15:45:49 CST
  936. ro.build.date.utc=1419925549
  937. ro.build.host=midserver
  938. ro.build.tags=test-keys
  939. ro.build.type=eng
  940. ro.build.user=firefly
  941. ro.build.display.id=rk3288-eng 4.4.4 KTU84Q eng.firefly.20141230.154515 test-keys
  942. ro.build.product=rk3288
  943. ro.build.version.sdk=19
  944. ro.build.version.release=4.4.4
  945. ro.build.version.codename=REL
  946. ro.build.version.incremental=eng.firefly.20141230.154515
  947. ro.build.description=rk3288-eng 4.4.4 KTU84Q eng.firefly.20141230.154515 test-keys
  948. ro.build.fingerprint=rockchip/rk3288/rk3288:4.4.4/KTU84Q/eng.firefly.20141230.154515:eng/test-keys
  949. ro.build.characteristics=tablet
  950. ro.rksdk.version=RK30_ANDROID4.4.4-SDK-v1.00.00
  951. ro.voice.capable=false
  952. ro.ap_mdm=-1
  953. ro.config.ringtone=Ring_Synth_04.ogg
  954. ro.config.alarm_alert=Alarm_Classic.ogg
  955. ro.config.notification_sound=pixiedust.ogg
  956. ro.kernel.android.checkjni=0
  957. ro.secure=0
  958. ro.tether.denied=false
  959. ro.carrier=unknown
  960. ro.default.size=100
  961. ro.factory.tool=0
  962. ro.factory.hasGPS=false
  963. ro.factory.hasUMS=true
  964. ro.factory.without_battery=false
  965. ro.factory.storage_suppntfs=true
  966. ro.product.cpu.abi=armeabi-v7a
  967. ro.product.cpu.abi2=armeabi
  968. ro.product.ota.host=www.rockchip.com:2300
  969. ro.product.name=rk3288
  970. ro.product.board=rk30sdk
  971. ro.product.brand=rockchip
  972. ro.product.model=rk3288
  973. ro.product.device=rk3288
  974. ro.product.locale.region=US
  975. ro.product.locale.language=en
  976. ro.product.version=1.0.0
  977. ro.product.usbfactory=rockchip_usb
  978. ro.product.manufacturer=rockchip
  979. ro.baseband=unknown
  980. ro.bootmode=emmc
  981. ro.hardware=rk30board
  982. ro.opengles.version=196608
  983. ro.revision=0
  984. ro.bootloader=unknown
  985. ro.debuggable=1
  986. ro.ap_has_alsa=-1
  987. ro.factorytest=0
  988. ro.setupwizard.mode=OPTIONAL
  989. ro.ap_data_only=-1
  990. ro.ap_has_earphone=-1
  991. sf.power.control=8847360
  992. net.bt.name=Android
  993. net.change=net.bt.name
  994. ril.function.dataonly=1
  995. sys.hwc.compose_policy=6
  996. sys.rkadb.root=0
  997. sys.wallpaper.rgb565=0
  998. sys.resolution.changed=false
  999. init.svc.adbd=running
  1000. init.svc.console=restarting
  1001. init.svc.ueventd=running
  1002. init.svc.recovery=running
  1003. rild.libargs=-d /dev/ttyACM0
  1004. rild.libpath=/system/lib/libril-rk29-dataonly.so
  1005. rild.libpath1=/system/lib/libreference-ril-mt6229.so
  1006. rild.libpath2=/system/lib/libreference-ril-mu509.so
  1007. rild.libpath4=/system/lib/libreference-ril-mw100.so
  1008. rild.libpath6=/system/lib/libreference-ril-sc6610.so
  1009. rild.libpath7=/system/lib/libreference-ril-m51.so
  1010. rild.libpath8=/system/lib/libreference-ril-mt6250.so
  1011. rild.libpath9=/system/lib/libreference-ril-c66a.so
  1012. rild.libpath10=/system/lib/libreference-ril-sew290.so
  1013. rild.libpath11=/system/lib/libreference-ril-u5501.so
  1014. rild.libpath12=/system/lib/libreference-ril-u7501.so
  1015. rild.libpath13=/system/lib/libreference-ril-aw706.so
  1016. rild.libpath14=/system/lib/libreference-ril-a85xx.so
  1017. rild.libpath15=/system/lib/libreference-ril-e1230s.so
  1018. wifi.interface=wlan0
  1019. wifi.supplicant_scan_interval=15
  1020. debug.nfc.se=false
  1021. debug.nfc.fw_download=false
  1022. rild1.libpath=/system/lib/libreference-ril-sc6610-1.so
  1023. rild3.libpath=/system/lib/libril-rk29-dataonly.so
  1024. dalvik.vm.jniopts=warnonly
  1025. dalvik.vm.heapsize=512m
  1026. dalvik.vm.lockprof.threshold=500
  1027. dalvik.vm.heapmaxfree=8m
  1028. dalvik.vm.heapminfree=512k
  1029. dalvik.vm.dexopt-flags=m=y
  1030. dalvik.vm.heapstartsize=16m
  1031. dalvik.vm.heapgrowthlimit=192m
  1032. dalvik.vm.stack-trace-file=/data/anr/traces.txt
  1033. dalvik.vm.heaptargetutilization=0.75
  1034. persist.sys.ui.hw=true
  1035. persist.sys.usb.config=mass_storage,adb
  1036. persist.sys.dalvik.vm.lib=libdvm.so
  1037. persist.sys.timezone=
  1038. persist.sys.strictmode.visual=false
  1039. persist.tegra.nvmmlite=1
  1040. testing.mediascanner.skiplist=/mnt/internal_sd/Android/
  1041. keyguard.no_require_sim=true
  1042. ExternalSD_ROOT=/mnt/external_sd
  1043. InternalSD_ROOT=/mnt/internal_sd
  1044. UserVolumeLabel=RockChips
  1045. failed to create /metadata dir,err=File exists!
  1046. in do_wipe_all
  1047. E:clone_data_if_exist->can't find databk cmdline
  1048. E/ [File] : bootable/recovery/recovery.cpp; [Line] : 418; [Func] : int clone_data_if_exist(); clone_data_if_exist->can't find databk cm        dline
  1049. Formatting /data...
  1050. format '/dev/block/platform/ff0f0000.rksdmmc/by-name/userdata' to ext4 filesystem
  1051. executing '/sbin/mke2fs'
  1052. executed '/sbin/mke2fs' done
  1053. executed '/sbin/mke2fs' return 0
  1054. executing '/sbin/e2fsck'
  1055. e2fsck 1.41.14 (22-Dec-2010)
  1056. Pass 1: Checking inodes, blocks, and sizes
  1057. Pass 2: Checking directory structure
  1058. Pass 3: Checking directory connectivity
  1059. Pass 4: Checking reference counts
  1060. Pass 5: Checking group summary information
  1061. /dev/block/platform/ff0f0000.rksdmmc/by-name/userdata: 11/65536 files (0.0% non-contiguous), 12635/262144 blocks
  1062. executed '/sbin/e2fsck' done
  1063. executed '/sbin/e2fsck' return 0
  1064. [    9.550402] rk3288-hdmi ff980000.hdmiattimoved.che...
  1065. .550414] hdmi connect to lcdc1
  1066. [    9.550454] rk3288-lcdc lcdc1: lcdc1: dclk:74250000>>fps:60
  1067. [    9.550462] rk3288-lcdc lcdc1: wakeup from standby!
  1068. [    9.550472] rk3288-lcdc lcdc1: lcdc1: dclk:74250000>>fps:60
  1069. [    9.556127] EXT4-fs (mmcblk0p12): recovery complete
  1070. [    9.556140] EXT4-fs (mmcblk0p12): mounted filesystem with ordered data mode. Opts:
  1071. [   11.735906] EXT4-fs (mmcblk0p13): mounted filesystem with ordered data mode. Opts:
  1072. format '/dev/block/platform/ff0f0000.rksdmmc/by-name/cache' to ext4 filesystem
  1073. executing '/sbin/mke2fs'
  1074. [   11.843711] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  1075. [   11.844369] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  1076. [   11.844380] ======int_1st: 0 0 0 0 , int_2nd: 0 0 0 0 ======
  1077. [   11.845022] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  1078. [   11.902146] test_i2c-394: Enter
  1079. [   11.902879] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  1080. [   11.942367] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  1081. [   11.942392] test_i2c-413: Exit
  1082. [   11.942398] ------gslX680 test_i2c error------
  1083. executed '/sbin/mke2fs' done
  1084. executed '/sbin/mke2fs' return 0
  1085. executing '/sbin/e2fsck'
  1086. e2fsck 1.41.14 (22-Dec-2010)
  1087. Pass 1: Checking inodes, blocks, and sizes
  1088. Pass 2: Checking directory structure
  1089. Pass 3: Checking directory connectivity
  1090. Pass 4: Checking reference counts
  1091. Pass 5: Checking group summary information
  1092. /dev/block/platform/ff0f0000.rksdmmc/by-name/cache: 11/32768 files (9.1% non-contiguous), 5137/32768 blocks
  1093. executed '/sbin/e2fsck' done
  1094. executed '/sbin/e2fsck' return 0
  1095. [   12.600939] EXT4-fs (mmcblk0p9): mounted filesystem with ordered data mode. Opts:
  1096. resize /system
  1097. executing '/sbin/e2fsck'
  1098. e2fsck 1.41.14 (22-Dec-2010)
  1099. Pass 1: Checking inodes, blocks, and sizes
  1100. Pass 2: Checking directory structure
  1101. Pass 3: Checking directory connectivity
  1102. Pass 4: Checking reference counts
  1103. Pass 5: Checking group summary information
  1104. system: 1748/43488 files (0.0% non-contiguous), 115840/196608 blocks
  1105. executed '/sbin/e2fsck' done
  1106. executed '/sbin/e2fsck' return 0
  1107. executing '/sbin/resize2fs'
  1108. resize2fs 1.41.14 (22-Dec-2010)
  1109. The filesystem is already 196608 blocks long.  Nothing to do!

  1111. executed '/sbin/resize2fs' done
  1112. executed '/sbin/resize2fs' return 0
  1113. D/ [File] : bootable/recovery/recovery.cpp; [Line] : 1957; [Func] : int do_wipe_all(Device*); to wipe radical_update_partition.
  1114. Formatting /radical_update...
  1115. format '/dev/block/platform/ff0f0000.rksdmmc/by-name/radical_update' to ext4 filesystem
  1116. executing '/sbin/mke2fs'
  1117. [   12.926129] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  1118. [   12.926151] ======read 0xb0: 0 0 0 0 ======
  1119. [   12.926807] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  1120. [   12.926817] ======int_1st: 0 0 0 0 , int_2nd: 0 0 0 0 ======
  1121. [   12.927474] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  1122. [   12.984481] test_i2c-394: Enter
  1123. [   12.985160] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  1124. [   13.024498] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  1125. [   13.024514] test_i2c-413: Exit
  1126. [   13.024520] ------gslX680 test_i2c error------
  1127. sh: applet not found
  1128. executed '/sbin/mke2fs' done
  1129. executed '/sbin/mke2fs' return 0
  1130. executing '/sbin/e2fsck'
  1131. e2fsck 1.41.14 (22-Dec-2010)
  1132. Pass 1: Checking inodes, blocks, and sizes
  1133. Pass 2: Checking directory structure
  1134. Pass 3: Checking directory connectivity
  1135. Pass 4: Checking reference counts
  1136. Pass 5: Checking group summary information
  1137. /dev/block/platform/ff0f0000.rksdmmc/by-name/radical_update: 11/16384 files (9.1% non-contiguous), 1549/16384 blocks
  1138. executed '/sbin/e2fsck' done
  1139. executed '/sbin/e2fsck' return 0
  1140. ordered data mode. Opts: cblFor14)tinountnt/inlesnalem w..
  1141. I/ [File] : bootable/recovery/roots.cpp; [Line] : 268; [Func] : format_volume; VolumeLabel: RockChips
  1142. format '/dev/block/platform/ff0f0000.rksdmmc/by-name/user' to vfat filesystem
  1143. executing '/sbin/mkdosfs'
  1144. opening /dev/block/platform/ff0f0000.rksdmmc/by-name/user
  1145. /dev/block/platform/ff0f0000.rksdmmc/by-name/user: 26094656 sectors in 1630916 FAT32 clusters (8192 bytes/cluster)
  1146. MBR type: 11
  1147. bps=512 spc=16 res=32 nft=2 mid=0xf0 spt=26120192 hds=0 hid=0 bsec=26120192 bspf=12752 rdcl=2 infs=1 bkbs=2
  1148. executed '/sbin/mkdosfs' done
  1149. executed '/sbin/mkdosfs' return 0
  1150. failed to create /mnt/external_sd dir,err=File exists!
  1151. W/ [File] : bootable/recovery/roots.cpp; [Line] : 139; [Func] : ensure_path_mounted; failed to mount /dev/block/mmcblk1p1 at /mnt/exter        nal_sd,type=vfat (No such file or directory)
  1152. W/ [File] : bootable/recovery/roots.cpp; [Line] : 144; [Func] : ensure_path_mounted; failed to mount /dev/block/mmcblk1p1 at /mnt/exter        nal_sd,type=ntfs (No such device)
  1153. W/ [File] : bootable/recovery/roots.cpp; [Line] : 155; [Func] : ensure_path_mounted; failed to mount /dev/block/mmcblk1 at /mnt/externa        l_sd,type=vfat (No such file or directory)
  1154. W/ [File] : bootable/recovery/roots.cpp; [Line] : 160; [Func] : ensure_path_mounted; failed to mount /dev/block/mmcblk1 at /mnt/externa        l_sd,type=ntfs (No such device)
  1155. I/ [File] : bootable/recovery/recovery.cpp; [Line] : 962; [Func] : void finish_recovery(const char*); clear bootloader message
  1156. Rebooting...
  1157. [   13.947343] SysRq : Emergency Remount R/O
  1158. [   13.948371] EXT4-fs (mmcblk0p12): re-mounted. Opts: (null)
  1159. [   13.953086] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
  1160. [   13.953759] EXT4-fs (mmcblk0p14): re-mounted. Opts: (null)
  1161. [   13.953816] Emergency Remount complete
  1162. [   14.008533] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  1163. [   14.009202] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  1164. [   14.009213] ======int_1st: 0 0 0 0 , int_2nd: 0 0 0 0 ======
  1165. [   14.009870] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  1166. [   14.046544] cpufreq: cpufreq: reboot set core rate=1200000000, volt=1100000
  1167. [   14.046717] mmcblk mmc0:0001: Unbalanced pm_runtime_enable!
  1168. [   14.076394] test_i2c-394: Enter
  1169. [   14.080177] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  1170. [   14.116737] gsl_ts_read set data address fail! ret=-11-0xfffffff5
  1171. [   14.122722] test_i2c-413: Exit
  1172. [   14.125721] ------gslX680 test_i2c error------
  1173. [   14.678113] Chenzy-------hkw-------es8323_i2c_shutdown
  1174. [   14.784240] dwc_otg_driver_shutdown: disconnect USB device mode
  1175. [   14.794061] Restarting system.
  1176. DDR Version 1.00 20141007
  1177. In
  1178. SRX
  1179. Channel a: DDR3 200MHz
  1180. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
  1181. Channel b: DDR3 200MHz
  1182. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
  1183. OUT


  1186. U-Boot 2014.10-RK3288-01 (Nov 27 2014 - 16:44:27)

  1188. CPU: rk3288
  1189. CPU's clock information:
  1190.     arm pll = 600000000HZ
  1191.     periph pll = 297000000HZ
  1192.     ddr pll = 200000000HZ
  1193.     codec pll = 384000000HZ
  1194. Board:  Rockchip platform Board
  1195. DRAM:  Found dram banks:1
  1196. Adding bank:0000000000000000(0000000080000000)
  1197. 128 MiB
  1198. storage init OK!
  1199. Using default environment

  1201. GetParam
  1202. check parameter success
  1203. Unknow param: MACHINE_MODEL:rk30sdk!
  1204. Unknow param: MACHINE_ID:007!
  1205. Unknow param: MANUFACTURER:RK30SDK!
  1206. Unknow param: PWR_HLD: 0,0,A,0,1!
  1207. failed to prepare fdt from boot!
  1208. power key: bank-0 pin-5
  1209. pmic:act8846
  1210. SecureBootEn = 0, SecureBootLock = 0

  1212. #Boot ver: 2014-11-27#2.19
  1213. sn:100612000000019D
  1214. checkKey
  1215. vbus = 1
  1216. no fuel gauge found
  1217. no fuel gauge found
  1218. read logo_on switch from dts [0]
  1219. no fuel gauge found
  1220. Hit any key to stop autoboot:  1
复制代码
下面是recovery的信息


恢复完是能够重启的。

B.第二个问题，我单独烧写resource.img分区的时候，串口的打印只能打印到Starting kernel ...然后后面什么都没有了！
C.第三个问题，如果我同时烧写misc.img和resource.img分区的时候，系统起不来，串口只能打印到Starting kernel ...,界面停留在firefly，
  adb有显示出来，但是连接不上

3.我单独烧写另外几个分区的时候，没有什么问题，那我觉得下面这两个就有问题，
  因为是第一次用这个板，所以也不知道啥原因，请问有人能提供帮忙么？
4.注：系统起不来的时候我是用Firefly-RK3288_PAD_Android4.4_201412301550.img来重新烧写一遍的，而之后烧写自己编译的时候，
      没有对烧写的参数做任何的修改。

作者: zhansb    时间: 2015-3-31 10:20
parameter有用SDK下面的吗，可以parameter把贴出来看看
作者: zhutousame    时间: 2015-3-31 10:36
多谢版主，我试了发现确实是parameter又问题，我拷贝了下面的这个
./FFTools/parameter/rk3288-3.10-uboot-android-data1G.parameter.txt
就好了
FIRMWARE_VER:4.4.2
MACHINE_MODEL:rk30sdk
MACHINE_ID:007
MANUFACTURER:RK30SDK
MAGIC: 0x5041524B
ATAG: 0x60000800
MACHINE: 3066
CHECK_MASK: 0x80
PWR_HLD: 0,0,A,0,1
#KERNEL_IMG: 0x62008000
#FDT_NAME: rk-kernel.dtb
#RECOVER_KEY: 1,1,0,20,0
CMDLINE:console=ttyS2 earlyprintk androidboot.hardware=rk30board androidboot.console=ttyS2 board.ap_has_alsa=0 init=/init initrd=0x62000000,0x00800000 mtdparts=rk29xxnand:0x00002000@0x00002000(uboot),0x00002000@0x00004000(misc),0x00008000@0x00006000(resource),0x00008000@0x0000e000(kernel),0x00010000@0x00016000(boot),0x00010000@0x00026000(recovery),0x0001a000@0x00036000(backup),0x00040000@0x00050000(cache),0x00002000@0x00090000(kpanic),0x00180000@0x00092000(system),0x00002000@0x00212000(metadata),0x00200000@0x00214000(userdata),0x00020000@0x00414000(radical_update),-@0x00434000(user)

作者: 烟云龙紫    时间: 2015-4-15 15:53
zhansb 发表于 2015-3-31 10:20
parameter有用SDK下面的吗，可以parameter把贴出来看看

这个问题具体怎么解决的呢，楼主或者版主能否给个说明，我这边也遇到此类似问题。我在Windows下用2.33烧写工具 烧写自己编译的固件不行，烧写官方给的固件都可以
作者: zhansb    时间: 2015-4-15 16:23
烟云龙紫 发表于 2015-4-15 15:53
这个问题具体怎么解决的呢，楼主或者版主能否给个说明，我这边也遇到此类似问题。我在Windows下用2.33烧 ...
我拷贝了下面的这个
./FFTools/parameter/rk3288-3.10-uboot-android-data1G.parameter.txt
楼上已经把解决问题的方法贴出来的
作者: 烟云龙紫    时间: 2015-4-15 17:36
zhansb 发表于 2015-4-15 16:23
楼上已经把解决问题的方法贴出来的

这个是SDK目录下的东西吗，我的SDK下没有这个目录的文件 ，只有一个RAR压缩包
作者: zhansb    时间: 2015-4-17 09:42
烟云龙紫 发表于 2015-4-15 17:36
这个是SDK目录下的东西吗，我的SDK下没有这个目录的文件 ，只有一个RAR压缩包

SDK更新一下
作者: shf1986    时间: 2016-1-29 14:12
我用的默认版，rk3288-3.10-uboot-android-data1G.parameter.txt跟楼主一样，还是不行......任何东西都没有改过，按官方文档来的就是不行，编译出来的misc.img和resource.img一起烧写，就出起不来的问题了......
楼主有什么高见么？
作者: syjh7370628    时间: 2016-4-4 14:05
本帖最后由 syjh7370628 于 2016-4-4 14:07 编辑

同样的问题得到解决，:lol不过我用Android开发工具v2.35，没办法打包成update.img,求助一下！！！:$


作者: firefly001    时间: 2016-6-28 20:02
同样，这个2.35用不了
作者: yayo2004    时间: 2016-6-30 09:18
syjh7370628 发表于 2016-4-4 14:05
同样的问题得到解决，不过我用Android开发工具v2.35，没办法打包成update.img,求助一下！！！

我也是，用这个工具无法生成UPDATE.IMG



欢迎光临 Firefly开源社区 (https://dev.t-firefly.com/) Powered by Discuz! X3.1