Firefly开源社区

标题: My RK3399 is not booting [打印本页]
作者: kannant    时间: 2020-2-18 14:10
标题: My RK3399 is not booting
I recently updated my firefly rk3399 board with android 7 industry version , first i get the boot logo , then i get erasing screen, again the board will reboot, after reboot the board is stuck at boot logo, we can put the board in to loader mode and maskrom mode. i also flashed the board with rockchip batch tool 1.8 by putting the board in to maskrom mode.
the result after flashing is same, that is i get the firefly logo, then i get erasing screen after that the board will reboot and it will freeze at boot logo. below is the log message
  1.                                                                                                 
  2. DDR Version 1.17 20190115                                                                       
  3. In                                                                                             
  4. Channel 0: DDR3, 800MHz                                                                        
  5. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB         
  6. Channel 1: DDR3, 800MHz                                                      
  7. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
  8. 256B stride                                                
  9. ch 0 ddrconfig = 0x101, ddrsize = 0x20                     
  10. ch 1 ddrconfig = 0x101, ddrsize = 0x20                     
  11. pmugrf_os_reg[2] = 0x32817281, stride = 0x9                 
  12. OUT                                                         
  13. Boot1: 2017-06-09, version: 1.09
  14. CPUId = 0x0
  15. ChipType = 0x10, 1827
  16. SdmmcInit=2 0
  17. BootCapSize=100000
  18. UserCapSize=14910MB
  19. FwPartOffset=2000 , 100000
  20. SdmmcInit=0 20
  21. StorageInit ok = 66753
  22. LoadTrustBL
  23. No find bl30.bin
  24. Load uboot, ReadLba = 2000
  25. Load OK, addr=0x200000, size=0x7a274
  26. RunBL31 0x10000
  27. NOTICE:  BL31: v1.3(debug):2bb878d
  28. NOTICE:  BL31: Built : 11:57:30, Jan  4 2019
  29. NOTICE:  BL31: Rockchip release version: v1.1
  30. INFO:    GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
  31. INFO:    Using opteed sec cpu_context!
  32. INFO:    boot cpu mask: 0
  33. INFO:    plat_rockchip_pmu_init(1181): pd status 3e
  34. INFO:    BL31: Initializing runtime services
  35. INFO:    BL31: Initializing BL32
  36. INF [0x0] TEE-CORE:init_primary_helper:337: Initializing (1.1.0-195-g8f090d20 #6 Fri Dec  7 06:11:20 UTC 2018 aarch64)

  38. INF [0x0] TEE-CORE:init_primary_helper:338: Release version: 1.2

  40. INF [0x0] TEE-CORE:init_teecore:83: teecore inits done
  41. INFO:    BL31: Preparing for EL3 exit to normal world
  42. INFO:    Entry point address = 0x200000
  43. INFO:    SPSR = 0x3c9


  46. U-Boot 2014.10-RK3399-06 (Sep 19 2019 - 17:08:57)

  48. CPU: rk3399
  49. cpu version = 0
  50. CPU's clock information:
  51.     aplll = 816000000HZ
  52.     apllb = 24000000HZ
  53.     gpll = 800000000HZ
  54.                aclk_periph_h = 133333333HZ, hclk_periph_h = 66666666HZ, pclk_periph_h = 33333333HZ
  55.                aclk_periph_l0 = 100000000HZ, hclk_periph_l0 = 100000000HZ, pclk_periph_l0 = 50000000HZ
  56.                hclk_periph_l1 = 100000000HZ, pclk_periph_l1 = 50000000HZ
  57.     cpll = 800000000HZ
  58.     dpll = 800000000HZ
  59.     vpll = 24000000HZ
  60.     npll = 24000000HZ
  61.     ppll = 676000000HZ
  62. Board:  Rockchip platform Board
  63. Uboot as second level loader
  64. DRAM:  Found dram banks: 1
  65. Adding bank:0000000000200000(000000007fe00000)
  66. Reserve memory for trust os.
  67. dram reserve bank: base = 0x08400000, size = 0x01e00000
  68. 128 MiB
  69. SdmmcInit = 0 20
  70. storage init OK!
  71. Using default environment

  73. GetParam
  74. remotectl v0.1
  75. pwm freq=0xb8320
  76. pwm_freq_nstime=0x52d
  77. Load FDT from resource image.
  78. power key: bank-0 pin-5
  79. can't find dts node for fixed
  80. I2C Send Start Bit Timeout
  81. No pmic detect.
  82. can't find dts node for pwm1
  83. set pwm voltage ok,pwm_id =2 vol=1000000,pwm_value=66
  84. CPU's clock information:
  85.     aplll = 816000000HZ
  86.     apllb = 24000000HZ
  87.     gpll = 800000000HZ
  88.                aclk_periph_h = 133333333HZ, hclk_periph_h = 66666666HZ, pclk_periph_h = 33333333HZ
  89.                aclk_periph_l0 = 100000000HZ, hclk_periph_l0 = 100000000HZ, pclk_periph_l0 = 50000000HZ
  90.                hclk_periph_l1 = 100000000HZ, pclk_periph_l1 = 50000000HZ
  91.     cpll = 800000000HZ
  92.     dpll = 800000000HZ
  93.     vpll = 24000000HZ
  94.     npll = 24000000HZ
  95.     ppll = 676000000HZ
  96. SecureBootEn = 0, SecureBootLock = 0

  98. #Boot ver: 2019-09-19#1.09
  99. empty serial no.
  100. normal boot.
  101. checkKey
  102. vbus = 0
  103. board_fbt_key_pressed: ir_keycode = 0x0, frt = 0
  104. no fuel gauge found
  105. no fuel gauge found
  106. failed to find phy node
  107. failed to find panel driver
  108. read logo on state from dts [1]
  109. no fuel gauge found
  110. can't find dts node for deviceinfo
  111. dw_rk_hdmi_register:fail to read deviceinfo
  112. hdmi baseparamer 0x0@0-0
  113. [EDID-EXTEND] It is a  CEA 861 Series Extension.
  114. no baseparametr,find best edid mode,vic=16
  115. hdmi_dev->video.vic is 4
  116. rk lcdc - 0 dclk set: dclk = 74250000HZ, pll select = 0, div = 1
  117. rockchip_panel_prepare: failed to find panel prepare funcs
  118. hdmi_dev_config_video vic 4 color_output 3 color_output_depth 8
  119. pixel clk is 74250000 tmds clk is 74250000
  120. hsync_pol 1 vsync_pol 1
  121. [HDMI] sucess output HDMI.
  122. PHY PLL not locked: PCLK_ON=1,TMDSCLK_ON=0
  123. rockchip_panel_enable: failed to find panel prepare funcs
  124. ERROR: [get_entry_ram]: Cannot find logo_kernel.bmp!
  125. failed to display kernel logo
  126. checkKey
  127. vbus = 0
  128. board_fbt_key_pressed: ir_keycode = 0x0, frt = 0
  129. Hit any key to stop autoboot:  0
  130. load fdt from resouce.
  131. vendor read error!
  132. Set oem_unlocked=0Secure Boot state: 0
  133. kernel   @ 0x00280000 (0x0125a008)
  134. ramdisk  @ 0x04bf0000 (0x001adadc)
  135. bootrk: do_bootm_linux...
  136.    Loading Device Tree to 0000000004600000, end 0000000004616560 ... OK
  137. Add bank:0000000000200000, 0000000008200000
  138. Add bank:000000000a200000, 0000000075e00000
  139. WARNING: could not set reg FDT_ERR_BADOFFSET.

  141. Starting kernel ...

  143. [    0.000000] Booting Linux on physical CPU 0x0
  144. [    0.000000] Initializing cgroup subsys cpuset
  145. [    0.000000] Initializing cgroup subsys cpu
  146. [    0.000000] Initializing cgroup subsys cpuacct
  147. [    0.000000] Initializing cgroup subsys schedtune
  148. [    0.000000] Linux version 4.4.103 (chengd@tchipserver2) (gcc version 4.9 20150123 (prerelease) (GCC) ) #67 SMP PREEMPT Thu Sep 19 17:10:50 CST 2019
  149. [    0.000000] Boot CPU: AArch64 Processor [410fd034]
  150. [    0.000000] earlycon: Early serial console at MMIO32 0xff1a0000 (options '')
  151. [    0.000000] bootconsole [uart0] enabled
  152. [    0.000000] hdmi init vic is -1
  153. [    0.000000] Reserved memory: failed to reserve memory for node 'stb-devinfo@00000000': base 0x0000000000000000, size 0 MiB
  154. [    0.000000] cma: Reserved 16 MiB at 0x000000007f000000
  155. [    0.000000] psci: probing for conduit method from DT.
  156. [    0.000000] psci: PSCIv1.0 detected in firmware.
  157. [    0.000000] psci: Using standard PSCI v0.2 function IDs
  158. [    0.000000] psci: Trusted OS migration not required
  159. [    0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc07eef9000 s45504 r8192 d32320 u86016
  160. [    0.000000] Detected VIPT I-cache on CPU0
  161. [    0.000000] CPU features: enabling workaround for ARM erratum 845719
  162. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 507912
  163. [    0.000000] Kernel command line: earlycon=uart8250,mmio32,0xff1a0000 swiotlb=1 androidboot.baseband=N/A androidboot.selinux=permissive androidboot.hardware=rk30boa0
  164. [    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
  165. [    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
  166. [    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
  167. [    0.000000] software IO TLB [mem 0x7eeb1000-0x7eef1000] (0MB) mapped at [ffffffc07eeb1000-ffffffc07eef0fff]
  168. [    0.000000] Memory: 1988592K/2064384K available (11006K kernel code, 1640K rwdata, 5260K rodata, 832K init, 1073K bss, 59408K reserved, 16384K cma-reserved)
  169. [    0.000000] Virtual kernel memory layout:
  170. [    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
  171. [    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000   (   246 GB)
  172. [    0.000000]       .init : 0xffffff8009070000 - 0xffffff8009140000   (   832 KB)
  173. [    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008b40000   ( 11008 KB)
  174. [    0.000000]     .rodata : 0xffffff8008b40000 - 0xffffff8009070000   (  5312 KB)
  175. [    0.000000]       .data : 0xffffff8009140000 - 0xffffff80092da008   (  1641 KB)
  176. [    0.000000]     vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
  177. [    0.000000]               0xffffffbdc0008000 - 0xffffffbdc2000000   (    31 MB actual)
  178. [    0.000000]     fixed   : 0xffffffbffe7fd000 - 0xffffffbffec00000   (  4108 KB)
  179. [    0.000000]     PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000   (    16 MB)
  180. [    0.000000]     memory  : 0xffffffc000200000 - 0xffffffc080000000   (  2046 MB)
  181. [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
  182. [    0.000000] Preemptible hierarchical RCU implementation.
  183. [    0.000000]  Build-time adjustment of leaf fanout to 64.
  184. [    0.000000]  RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
  185. [    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6
  186. [    0.000000] NR_IRQS:64 nr_irqs:64 0
  187. [    0.000000] GIC: Using split EOI/Deactivate mode
  188. [    0.000000] ITS: /interrupt-controller@fee00000/interrupt-controller@fee20000
  189. [    0.000000] ITS: allocated 65536 Devices @a200000 (psz 64K, shr 0)
  190. [    0.000000] ITS: using cache flushing for cmd queue
  191. [    0.000000] GIC: using LPI property table @0x000000000a280000
  192. [    0.000000] ITS: Allocated 1792 chunks for LPIs
  193. [    0.000000] CPU0: found redistributor 0 region 0:0x00000000fef00000
  194. [    0.000000] CPU0: using LPI pending table @0x000000000a290000
  195. [    0.000000] GIC: using cache flushing for LPI property table
  196. [    0.000000] GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
  197. [    0.000000] GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
  198. [    0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop0_frac as parent of dclk_vop0, rate changes may not work
  199. [    0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop1_frac as parent of dclk_vop1, rate changes may not work
  200. [    0.000000] rockchip_cpuclk_pre_rate_change: limiting alt-divider 33 to 31
  201. [    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
  202. [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
  203. [    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
  204. [    0.001959] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
  205. [    0.002949] pid_max: default: 32768 minimum: 301
  206. [    0.003477] Security Framework initialized
  207. [    0.003877] SELinux:  Initializing.
  208. [    0.004298] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
  209. [    0.004945] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
  210. [    0.006392] Initializing cgroup subsys freezer
  211. [    0.006831] Initializing cgroup subsys debug
  212. [    0.008143] sched-energy: Sched-energy-costs installed from DT
  213. [    0.008706] CPU0: update cpu_capacity 401
  214. [    0.009173] ASID allocator initialised with 65536 entries
  215. [    0.026002] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
  216. [    0.027285] Platform MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
  217. [    0.039397] Detected VIPT I-cache on CPU1
  218. [    0.039428] CPU1: found redistributor 1 region 0:0x00000000fef20000
  219. [    0.039463] CPU1: using LPI pending table @0x000000000a3f0000
  220. [    0.039505] CPU1: update cpu_capacity 401
  221. [    0.039509] CPU1: Booted secondary processor [410fd034]
  222. [    0.049390] Detected VIPT I-cache on CPU2
  223. [    0.049410] CPU2: found redistributor 2 region 0:0x00000000fef40000
  224. [    0.049442] CPU2: using LPI pending table @0x000000007c020000
  225. [    0.049471] CPU2: update cpu_capacity 401
  226. [    0.049474] CPU2: Booted secondary processor [410fd034]
  227. [    0.059429] Detected VIPT I-cache on CPU3
  228. [    0.059448] CPU3: found redistributor 3 region 0:0x00000000fef60000
  229. [    0.059481] CPU3: using LPI pending table @0x000000007c060000
  230. [    0.059508] CPU3: update cpu_capacity 401
  231. [    0.059511] CPU3: Booted secondary processor [410fd034]
  232. [    0.069478] Detected PIPT I-cache on CPU4
  233. [    0.069507] CPU4: found redistributor 100 region 0:0x00000000fef80000
  234. [    0.069546] CPU4: using LPI pending table @0x000000007c0a0000
  235. [    0.069586] CPU4: update cpu_capacity 1024
  236. [    0.069589] CPU4: Booted secondary processor [410fd082]
  237. [    0.079500] Detected PIPT I-cache on CPU5
  238. [    0.079517] CPU5: found redistributor 101 region 0:0x00000000fefa0000
  239. [    0.079554] CPU5: using LPI pending table @0x000000007c0e0000
  240. [    0.079581] CPU5: update cpu_capacity 1024
  241. [    0.079584] CPU5: Booted secondary processor [410fd082]
  242. [    0.079669] Brought up 6 CPUs
  243. [    0.092098] SMP: Total of 6 processors activated.
  244. [    0.092553] CPU features: detected feature: GIC system register CPU interface
  245. [    0.093241] CPU: All CPU(s) started at EL2
  246. [    0.093673] alternatives: patching kernel code
  247. [    0.095768] devtmpfs: initialized
  248. [    0.116262] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
  249. [    0.117207] futex hash table entries: 2048 (order: 5, 131072 bytes)
  250. [    0.118516] pinctrl core: initialized pinctrl subsystem
  251. [    0.120571] Failed to find legacy iommu devices
  252. [    0.121382] NET: Registered protocol family 16
  253. [    0.122148] schedtune: init normalization constants...
  254. [    0.122635] schedtune: CLUSTER[0-3]      min_pwr:    56 max_pwr:   222
  255. [    0.123249] schedtune: CPU[0]            min_pwr:     0 max_pwr:   222
  256. [    0.123862] schedtune: CPU[1]            min_pwr:     0 max_pwr:   222
  257. [    0.124487] schedtune: CPU[2]            min_pwr:     0 max_pwr:   222
  258. [    0.125099] schedtune: CPU[3]            min_pwr:     0 max_pwr:   222
  259. [    0.125712] schedtune: CLUSTER[4-5]      min_pwr:    65 max_pwr:  1108
  260. [    0.126325] schedtune: CPU[4]            min_pwr:     0 max_pwr:  1108
  261. [    0.126937] schedtune: CPU[5]            min_pwr:     0 max_pwr:  1108
  262. [    0.127549] schedtune: SYSTEM            min_pwr:   121 max_pwr:  4434
  263. [    0.128167] schedtune: using normalization constants mul: 3862781856 sh1: 1 sh2: 12
  264. [    0.128885] schedtune: verify normalization constants...
  265. [    0.129384] schedtune: max_pwr/2^0: 4313 => norm_pwr:  1024
  266. [    0.129908] schedtune: max_pwr/2^1: 2156 => norm_pwr:   511
  267. [    0.130431] schedtune: max_pwr/2^2: 1078 => norm_pwr:   255
  268. [    0.130955] schedtune: max_pwr/2^3:  539 => norm_pwr:   127
  269. [    0.131478] schedtune: max_pwr/2^4:  269 => norm_pwr:    63
  270. [    0.132006] schedtune: max_pwr/2^5:  134 => norm_pwr:    31
  271. [    0.132530] schedtune: configured to support 5 boost groups
  272. [    0.142043] cpuidle: using governor ladder
  273. [    0.152047] cpuidle: using governor menu
  274. [    0.152429] Registered FIQ tty driver
  275. [    0.153093] vdso: 2 pages (1 code @ ffffff8008b46000, 1 data @ ffffff8009144000)
  276. [    0.153814] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
  277. [    0.155849] DMA: preallocated 2048 KiB pool for atomic allocations
  278. [    0.176903] console [pstore0] enabled
  279. [    0.177480] pstore: Registered ramoops as persistent store backend
  280. [    0.178065] ramoops: attached 0xf0000@0x110000, ecc: 0/0
  281. [    0.180784] fiq debugger fiq mode enabled
  282. [ [    0.181422] console [ttyFIQ0] enabled
  283.    0.181422] console [ttyFIQ0] enabled
  284. [[    0.182096] bootconsole [uart0] disabled
  285.     0.182096] bootconsole [uart0] disabled
  286. [    0.183009] Registered fiq debugger ttyFIQ0
  287. [    0.213965] Rockchip hdmi driver version 2.0
  288. .
  289. [    0.216285] iommu: Adding device ff650000.vpu_service to group 0
  290. [    0.216363] iommu: Adding device ff660000.rkvdec to group 1
  291. [    0.216428] iommu: Adding device ff670000.iep to group 2
  292. [    0.216522] iommu: Adding device ff8f0000.vop to group 3
  293. [    0.216597] iommu: Adding device ff900000.vop to group 4
  294. [    0.216705] iommu: Adding device ff910000.isp to group 5
  295. [    0.216785] iommu: Adding device ff920000.isp to group 6
  296. [    0.217499] rk_iommu ff670800.iommu: can't get aclk
  297. [    0.217520] rk_iommu ff670800.iommu: can't get hclk
  298. [    0.218382] SCSI subsystem initialized
  299. [    0.218722] usbcore: registered new interface driver usbfs
  300. [    0.218771] usbcore: registered new interface driver hub
  301. [    0.218850] usbcore: registered new device driver usb
  302. [    0.219251] media: Linux media interface: v0.10
  303. [    0.219292] Linux video capture interface: v2.00
  304. [    0.219425] pps_core: LinuxPPS API ver. 1 registered
  305. [    0.219438] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  306. [    0.219464] PTP clock support registered
  307. [    0.221029] Advanced Linux Sound Architecture Driver Initialized.
  308. [    0.221547] Bluetooth: Core ver 2.21
  309. [    0.221581] NET: Registered protocol family 31
  310. [    0.221593] Bluetooth: HCI device and connection manager initialized
  311. [    0.221610] Bluetooth: HCI socket layer initialized
  312. [    0.221627] Bluetooth: L2CAP socket layer initialized
  313. [    0.221656] Bluetooth: SCO socket layer initialized
  314. [    0.222692] rockchip-cpuinfo cpuinfo: Serial         : f4b0799a58def9f8
  315. [    0.223192] clocksource: Switched to clocksource arch_sys_counter
  316. [    0.267242] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
  317. [    0.267499] NET: Registered protocol family 2
  318. [    0.267942] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
  319. [    0.268083] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
  320. [    0.268361] TCP: Hash tables configured (established 16384 bind 16384)
  321. [    0.268440] UDP hash table entries: 1024 (order: 3, 32768 bytes)
  322. [    0.268502] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
  323. [    0.268673] NET: Registered protocol family 1
  324. [    0.269187] Trying to unpack rootfs image as initramfs...
  325. [    0.358236] Freeing initrd memory: 1716K
  326. [    0.358757] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
  327. [    0.358849] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
  328. [    0.361438] audit: initializing netlink subsys (disabled)
  329. [    0.361507] audit: type=2000 audit(0.356:1): initialized
  330. [    0.366605] VFS: Disk quotas dquot_6.6.0
  331. [    0.366731] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
  332. [    0.368115] fuse init (API version 7.23)
  333. [    0.369234]
  334. [    0.369234] TEE Core Framework initialization (ver 1:0.1)
  335. [    0.369266] TEE armv7 Driver initialization
  336. [    0.369636] tz_tee_probe: name="armv7sec", id=0, pdev_name="armv7sec.0"
  337. [    0.369655] TEE core: Alloc the misc device "opteearmtz00" (id=0)
  338. [    0.369832] TEE Core: Register the misc device "opteearmtz00" (id=0,minor=62)
  339. [    0.373688] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
  340. [    0.373714] io scheduler noop registered
  341. [    0.373884] io scheduler cfq registered (default)
  342. [    0.375167] rockchip-usb2phy ff770000.syscon:usb2-phy@e460: vbus_drv is not assigned
  343. [    0.380320] rockchip-pcie f8000000.pcie: no vpcie3v3 regulator found
  344. [    0.380348] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found
  345. [    0.380371] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found
  346. [    0.903261] rockchip-pcie f8000000.pcie: PCIe link training gen1 timeout!
  347. [    0.904002] rockchip-pcie: probe of f8000000.pcie failed with error -110
  348. [    0.905967] iep: failed to find iep power down clock source.
  349. [    0.907053] IEP Power ON
  350. [    0.907509] IEP Power OFF
  351. [    0.907842] IEP Driver loaded succesfully
  352. [    0.908473] Module initialized.
  353. [    0.909101] rk-vcodec ff650000.vpu_service: probe device
  354. [    0.909157] rk-vcodec ff650000.vpu_service: vpu mmu dec ffffffc07c2fa410
  355. [    0.909320] rk-vcodec ff650000.vpu_service: allocator is drm
  356. [    0.909374] rk-vcodec ff650000.vpu_service: checking hw id 0
  357. [    0.909885] rk-vcodec ff650000.vpu_service: init success
  358. [    0.910505] rk-vcodec ff660000.rkvdec: probe device
  359. [    0.910552] rk-vcodec ff660000.rkvdec: vpu mmu dec ffffffc07c2fac10
  360. [    0.910691] rk-vcodec ff660000.rkvdec: allocator is drm
  361. [    0.910749] rk-vcodec ff660000.rkvdec: checking hw id 6876
  362. [    0.911081] rk-vcodec ff660000.rkvdec: init success
  363. [    0.912774] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
  364. [    0.912793] dma-pl330 ff6d0000.dma-controller:       DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
  365. [    0.914146] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
  366. [    0.914165] dma-pl330 ff6e0000.dma-controller:   \0֫#�V֖�fVVkm_Chans-8 Num_Peri-20 Num_Events-16
  367. [    0.915781] Serial: 8250/16550 driver, 5 ports, �Q sharing disabled      [    0.918033] ff1a0000.serial: ttyS2 at MMIO 0xff1a0000 (irq = 37, base_baud = 1500000) A
  368. [    0.918614] ff370000.serial: ttyS4 at MMIO 0xff370000 (irq = 40, base_baud = 1500000) is a 16550A
  369. [    0.919008] [drm:drm_core_init] Initialized drm 1.1.0 20060810
  370. [    0.923978] mali ff9a0000.gpu: Failed to get regulator
  371. [    0.924001] mali ff9a0000.gpu: Power control initialization failed
  372. [    0.924303] Unable to detect cache hierarchy from DT for CPU 0
  373. [    0.932115] brd: module loaded
  374. [    0.946693] loop: module loaded
  375. [    0.947220] zram: Added device: zram0
  376. [    0.947830] SCSI Media Changer driver v0.25
  377. [    0.949278] rockchip-pinctrl pinctrl: pin gpio1-8 already requested by ff370000.serial; cannot claim for ff1d0000.spi
  378. [    0.949308] rockchip-pinctrl pinctrl: pin-40 (ff1d0000.spi) status -22
  379. [    0.949325] rockchip-pinctrl pinctrl: could not request pin 40 (gpio1-8) from group spi1-tx  on device rockchip-pinctrl
  380. [    0.949344] rockchip-spi ff1d0000.spi: Error applying setting, reverse things back
  381. [    0.949482] rockchip-spi ff1d0000.spi: Failed to request TX DMA channel
  382. [    0.949496] rockchip-spi ff1d0000.spi: Failed to request RX DMA channel
  383. [    0.950178] register spi return v = :0
  384. [    0.950229] tun: Universal TUN/TAP device driver, 1.6
  385. [    0.950240] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  386. [    0.951175] force_sf_dma_mode is ignored if force_thresh_dma_mode is set.
  387. [    0.951264] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
  388. [    0.951283] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
  389. [    0.951298] rk_gmac-dwmac fe300000.ethernet: RX delay(0x1b).
  390. [    0.951325] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
  391. [    0.951496] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
  392. [    0.956521] rk_gmac-dwmac fe300000.ethernet: init for RGMII
  393. [    0.956645] stmmac - user ID: 0x10, Synopsys ID: 0x35
  394. [    0.956656]  Ring mode enabled
  395. [    0.956665]  DMA HW capability register supported
  396. [    0.956674]  Normal descriptors
  397. [    0.956685]  RX Checksum Offload Engine supported (type 2)
  398. [    0.956696]  Wake-Up On Lan supported
  399. [    0.956740]  Enable RX Mitigation via HW Watchdog Timer
  400. [    1.025921] libphy: stmmac: probed
  401. [    1.025943] eth%d: PHY ID 001cc915 at 0 IRQ POLL (stmmac-0:00) active
  402. [    1.025957] eth%d: PHY ID 001cc915 at 1 IRQ POLL (stmmac-0:01)
  403. [    1.028188] PPP generic driver version 2.4.2
  404. [    1.028708] PPP BSD Compression module registered
  405. [    1.028728] PPP Deflate Compression module registered
  406. [    1.028759] PPP MPPE Compression module registered
  407. [    1.028778] NET: Registered protocol family 24
  408. [    1.028817] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
  409. [    1.028831] CSLIP: code copyright 1989 Regents of the University of California.
  410. [    1.028903] usbcore: registered new interface driver mt7601u
  411. [    1.028924] Rockchip WiFi SYS interface (V1.00) ...
  412. [    1.028990] usbcore: registered new interface driver catc
  413. [    1.029034] usbcore: registered new interface driver kaweth
  414. [    1.029051] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
  415. [    1.029090] usbcore: registered new interface driver pegasus
  416. [    1.029133] usbcore: registered new interface driver rtl8150
  417. [    1.029179] usbcore: registered new interface driver r8152
  418. [    1.029194] hso: drivers/net/usb/hso.c: Option Wireless
  419. [    1.029253] usbcore: registered new interface driver hso
  420. [    1.029301] usbcore: registered new interface driver asix
  421. [    1.029344] usbcore: registered new interface driver ax88179_178a
  422. [    1.029388] usbcore: registered new interface driver cdc_ether
  423. [    1.029434] usbcore: registered new interface driver cdc_eem
  424. [    1.029477] usbcore: registered new interface driver dm9601
  425. [    1.029527] usbcore: registered new interface driver smsc75xx
  426. [    1.029580] usbcore: registered new interface driver smsc95xx
  427. [    1.029626] usbcore: registered new interface driver gl620a
  428. [    1.029670] usbcore: registered new interface driver net1080
  429. [    1.029713] usbcore: registered new interface driver plusb
  430. [    1.029756] usbcore: registered new interface driver rndis_host
  431. [    1.029800] usbcore: registered new interface driver cdc_subset
  432. [    1.029843] usbcore: registered new interface driver zaurus
  433. [    1.029910] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
  434. [    1.029970] usbcore: registered new interface driver int51x1
  435. [    1.030014] usbcore: registered new interface driver kalmia
  436. [    1.030057] usbcore: registered new interface driver ipheth
  437. [    1.030103] usbcore: registered new interface driver sierra_net
  438. [    1.030149] usbcore: registered new interface driver cx82310_eth
  439. [    1.030201] usbcore: registered new interface driver cdc_ncm
  440. [    1.030246] usbcore: registered new interface driver qmi_wwan
  441. [    1.030290] usbcore: registered new interface driver cdc_mbim
  442. [    1.031515] rockchip-dwc3 usb@fe800000: failed to get drvdata dwc3
  443. [    1.047342] rockchip-dwc3 usb@fe900000: fail to get drvdata hcd
  444. [    1.047955] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  445. [    1.047974] ehci-pci: EHCI PCI platform driver
  446. [    1.048035] ehci-platform: EHCI generic platform driver
  447. [    1.051844] ehci-platform fe3c0000.usb: EHCI Host Controller
  448. [    1.051876] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 1
  449. [    1.052083] ehci-platform fe3c0000.usb: irq 30, io mem 0xfe3c0000
  450. [    1.059878] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
  451. [    1.060063] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
  452. [    1.060079] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  453. [    1.060093] usb usb1: Product: EHCI Host Controller
  454. [    1.060105] usb usb1: Manufacturer: Linux 4.4.103 ehci_hcd
  455. [    1.060117] usb usb1: SerialNumber: fe3c0000.usb
  456. [    1.060623] hub 1-0:1.0: USB hub found
  457. [    1.060672] hub 1-0:1.0: 1 port detected
  458. [    1.061222] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  459. [    1.061260] ohci-platform: OHCI generic platform driver
  460. [    1.061735] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
  461. [    1.061761] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 2
  462. [    1.061887] ohci-platform fe3e0000.usb: irq 31, io mem 0xfe3e0000
  463. [    1.117359] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
  464. [    1.117387] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  465. [    1.117402] usb usb2: Product: Generic Platform OHCI controller
  466. [    1.117415] usb usb2: Manufacturer: Linux 4.4.103 ohci_hcd
  467. [    1.117428] usb usb2: SerialNumber: fe3e0000.usb
  468. [    1.118065] hub 2-0:1.0: USB hub found
  469. [    1.118115] hub 2-0:1.0: 1 port detected
  470. [    1.119601] usbcore: registered new interface driver cdc_acm
  471. [    1.119616] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
  472. [    1.119700] usbcore: registered new interface driver usblp
  473. [    1.119763] usbcore: registered new interface driver cdc_wdm
  474. [    1.119827] usbcore: registered new interface driver uas
  475. [    1.119980] usbcore: registered new interface driver usb-storage
  476. [    1.120036] usbcore: registered new interface driver ums-alauda
  477. [    1.120099] usbcore: registered new interface driver ums-cypress
  478. [    1.120156] usbcore: registered new interface driver ums-datafab
  479. [    1.120210] usbcore: registered new interface driver ums_eneub6250
  480. [    1.120264] usbcore: registered new interface driver ums-freecom
  481. [    1.120319] usbcore: registered new interface driver ums-isd200
  482. [    1.120374] usbcore: registered new interface driver ums-jumpshot
  483. [    1.120429] usbcore: registered new interface driver ums-karma
  484. [    1.120484] usbcore: registered new interface driver ums-onetouch
  485. [    1.120544] usbcore: registered new interface driver ums-sddr09
  486. [    1.120599] usbcore: registered new interface driver ums-sddr55
  487. [    1.120655] usbcore: registered new interface driver ums-usbat
  488. [    1.120768] usbcore: registered new interface driver usbserial
  489. [    1.120821] usbcore: registered new interface driver usbserial_generic
  490. [    1.120862] usbserial: USB Serial support registered for generic
  491. [    1.120921] usbcore: registered new interface driver ch341
  492. [    1.120963] usbserial: USB Serial support registered for ch341-uart
  493. [    1.121021] usbcore: registered new interface driver cp210x
  494. [    1.121058] usbserial: USB Serial support registered for cp210x
  495. [    1.121129] usbcore: registered new interface driver option
  496. [    1.121169] usbserial: USB Serial support registered for GSM modem (1-port)
  497. [    1.121332] usbcore: registered new interface driver pl2303
  498. [    1.121369] usbserial: USB Serial support registered for pl2303
  499. [    1.121441] usbcore: registered new interface driver trancevibrator
  500. [    1.121460] usb20_otg: version 3.10a 21-DEC-2012
  501. [    1.121734] usb20_host: version 3.10a 21-DEC-2012
  502. [    1.126676] usbcore: registered new interface driver xpad
  503. [    1.126736] usbcore: registered new interface driver usb_acecad
  504. [    1.126787] usbcore: registered new interface driver aiptek
  505. [    1.126848] usbcore: registered new interface driver gtco
  506. [    1.126899] usbcore: registered new interface driver hanwang
  507. [    1.126947] usbcore: registered new interface driver kbtab
  508. [    1.126964] ==gsl_ts_init==
  509. [    1.126995] ret=0
  510. [    1.136812] .. rk pwm remotectl v1.1 init
  511. [    1.137036] input: ff420030.pwm as /devices/platform/ff420030.pwm/input/input0
  512. [    1.137621] sensor_register_slave:mma8452,id=17
  513. [    1.137646] sensor_register_slave:lis3dh,id=7
  514. [    1.137664] sensor_register_slave:mma7660,id=18
  515. [    1.137681] sensor_register_slave:lsm303d,id=22
  516. [    1.137698] sensor_register_slave:gs_mc3230,id=23
  517. [    1.137708] [Gsensor]   gsensor_init
  518. [    1.137726] sensor_register_slave:mpu6880_acc,id=24
  519. [    1.137743] sensor_register_slave:mpu6500_acc,id=25
  520. [    1.137761] sensor_register_slave:lsm330_acc,id=26
  521. [    1.137779] sensor_register_slave:akm8975,id=29
  522. [    1.137796] sensor_register_slave:akm8963,id=30
  523. [    1.137814] sensor_register_slave:l3g4200d,id=44
  524. [    1.137831] sensor_register_slave:l3g20d,id=45
  525. [    1.137849] sensor_register_slave:ewtsa,id=46
  526. [    1.137867] sensor_register_slave:lsm330_gyro,id=50
  527. [    1.137885] sensor_register_slave:cm3217,id=52
  528. [    1.137903] sensor_register_slave:cm3218,id=53
  529. [    1.138795] i2c /dev entries driver
  530. [    1.366539] usb 1-1: new high-speed USB device number 2 using ehci-platform
  531. [    1.490509] usb 1-1: New USB device found, idVendor=1a40, idProduct=0201
  532. [    1.490542] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
  533. [    1.490560] usb 1-1: Product: USB 2.0 Hub [MTT]
  534. [    1.491125] hub 1-1:1.0: USB hub found
  535. [    1.491256] hub 1-1:1.0: 7 ports detected
  536. [    1.769871] usb 1-1.4: new low-speed USB device number 3 using ehci-platform
  537. [    1.874886] usb 1-1.4: New USB device found, idVendor=04ca, idProduct=004b
  538. [    1.874918] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
  539. [    1.874936] usb 1-1.4: Product: USB Keyboard
  540. [    1.874952] usb 1-1.4: Manufacturer: Lite-On Technology Corp.
  541. [    2.139910] rk3x-i2c ff3c0000.i2c: timeout, ipd: 0x00, state: 1
  542. [    2.139962] fan53555-regulator 0-0040: Failed to get chip ID!
  543. [    2.140044] fan53555-regulator: probe of 0-0040 failed with error -110
  544. [    3.139903] rk3x-i2c ff3c0000.i2c: timeout, ipd: 0x00, state: 1
  545. [    3.139945] fan53555-regulator 0-0041: Failed to get chip ID!
  546. [    3.140006] fan53555-regulator: probe of 0-0041 failed with error -110
  547. [    4.139906] rk3x-i2c ff3c0000.i2c: timeout, ipd: 0x00, state: 1
  548. [    4.139950] rk808 0-001b: failed to read the chip id at 0x17
  549. [    4.140014] rk808: probe of 0-001b failed with error -110
  550. [    4.140049] rk3x-i2c ff3c0000.i2c: Initialized RK3xxx I2C bus at ffffff80098ac000
  551. [    4.140807] rk3x-i2c ff110000.i2c: Initialized RK3xxx I2C bus at ffffff80098ae000
  552. [    4.140926] rockchip-pinctrl pinctrl: pin gpio4-17 already requested by ff940000.hdmi; cannot claim for ff130000.i2c
  553. [    4.140943] rockchip-pinctrl pinctrl: pin-145 (ff130000.i2c) status -22
  554. [    4.140959] rockchip-pinctrl pinctrl: could not request pin 145 (gpio4-17) from group i2c3-xfer  on device rockchip-pinctrl
  555. [    4.140974] rk3x-i2c ff130000.i2c: Error applying setting, reverse things back
  556. [    4.141432] rk3x-i2c ff130000.i2c: Initialized RK3xxx I2C bus at ffffff80098b0000
  557. [    4.142996] fusb302 4-0022: Can't get property of role, set role to default DRP
  558. [    5.139909] rk3x-i2c ff3d0000.i2c: timeout, ipd: 0x00, state: 1
  559. [    6.139900] rk3x-i2c ff3d0000.i2c: timeout, ipd: 0x00, state: 1
  560. [    7.139902] rk3x-i2c ff3d0000.i2c: timeout, ipd: 0x00, state: 1
  561. [    8.139909] rk3x-i2c ff3d0000.i2c: timeout, ipd: 0x00, state: 1
  562. [    9.139901] rk3x-i2c ff3d0000.i2c: timeout, ipd: 0x00, state: 1
  563. [   10.139900] rk3x-i2c ff3d0000.i2c: timeout, ipd: 0x00, state: 1
  564. [   11.139887] rk3x-i2c ff3d0000.i2c: timeout, ipd: 0x00, state: 1
  565. [   12.139901] rk3x-i2c ff3d0000.i2c: timeout, ipd: 0x00, state: 1
  566. [   13.139900] rk3x-i2c ff3d0000.i2c: timeout, ipd: 0x00, state: 1
  567. [   14.139898] rk3x-i2c ff3d0000.i2c: timeout, ipd: 0x00, state: 1
  568. [   15.139896] rk3x-i2c ff3d0000.i2c: timeout, ipd: 0x00, state: 1
  569. [   16.139907] rk3x-i2c ff3d0000.i2c: timeout, ipd: 0x00, state: 1
  570. [   17.139896] rk3x-i2c ff3d0000.i2c: timeout, ipd: 0x00, state: 1
  571. [   18.139897] rk3x-i2c ff3d0000.i2c: timeout, ipd: 0x00, state: 1
  572. [   19.139898] rk3x-i2c ff3d0000.i2c: timeout, ipd: 0x00, state: 1
  573. [   20.139903] rk3x-i2c ff3d0000.i2c: timeout, ipd: 0x00, state: 1
  574. [   21.139900] rk3x-i2c ff3d0000.i2c: timeout, ipd: 0x00, state: 1
  575. [   21.140390] fusb302 4-0022: port 0 probe success with role ROLE_MODE_DRP, try_role ROLE_MODE_NONE
  576. [   21.140430] rk3x-i2c ff3d0000.i2c: Initialized RK3xxx I2C bus at ffffff80098b2000
  577. [   21.141602] IR NEC protocol handler initialized
  578. [   21.141653] IR RC5(x/sz) protocol handler initialized
  579. [   21.141671] IR RC6 protocol handler initialized
  580. [   21.141688] IR JVC protocol handler initialized
  581. [   21.141704] IR Sony protocol handler initialized
  582. [   21.141718] IR SANYO protocol handler initialized
  583. [   21.141733] IR Sharp protocol handler initialized
  584. [   21.141748] IR MCE Keyboard/mouse protocol handler initialized
  585. [   21.141763] IR XMP protocol handler initialized
  586. [   21.142085] usbcore: registered new interface driver uvcvideo
  587. [   21.142096] USB Video Class driver (1.1.1)
  588. [   21.142115] CamSys driver version: v0.38.0, CamSys head file version: v1.0.0
  589. [   21.148167] __power_supply_register: Expected proper parent device for 'test_ac'
  590. [   21.148338] __power_supply_register: Expected proper parent device for 'test_battery'
  591. [   21.148705] thermal thermal_zone2: power_allocator: sustainable_power will be estimated
  592. [   21.148828] __power_supply_register: Expected proper parent device for 'test_usb'
  593. [   21.151794] rk_tsadcv2_temp_to_code: Invalid conversion table: code=1023, temperature=2147483647
  594. [   21.152908] device-mapper: uevent: version 1.0.3
  595. [   21.153409] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
  596. [   21.153695] Bluetooth: HCI UART driver ver 2.3
  597. [   21.153709] Bluetooth: HCI UART protocol H4 registered
  598. [   21.153720] Bluetooth: HCI UART protocol LL registered
  599. [   21.153736] rtk_btusb: RTKBT_RELEASE_NAME: 20170109_TV_ANDROID_6.x
  600. [   21.153746] rtk_btusb: Realtek Bluetooth USB driver module init, version 4.1.2
  601. [   21.153756] rtk_btusb: Register usb char device interface for BT driver
  602. [   21.154037] usbcore: registered new interface driver rtk_btusb
  603. [   21.154587] cpu cpu0: leakage=15
  604. [   21.154687] cpu cpu0: Failed to get cpu_reg
  605. [   21.154954] cpu cpu4: leakage=26
  606. [   21.154993] cpu cpu4: Failed to get cpu_reg
  607. [   21.156163] sdhci: Secure Digital Host Controller Interface driver
  608. [   21.156175] sdhci: Copyright(c) Pierre Ossman
  609. [   21.156191] Synopsys Designware Multimedia Card Interface Driver
  610. [   21.157407] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
  611. [   21.157567] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
  612. [   21.157589] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
  613. [   21.157653] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo
  614. [   21.157699] dwmmc_rockchip fe310000.dwmmc: 'clock-freq-min-max' property was deprecated.
  615. [   21.157733] dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found
  616. [   21.157746] dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found
  617. [   21.158836] dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode.
  618. [   21.158913] dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller.
  619. [   21.158934] dwmmc_rockchip fe320000.dwmmc: Version ID is 270a
  620. [   21.158998] dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 26,32 bit host data width,256 deep fifo
  621. [   21.159025] dwmmc_rockchip fe320000.dwmmc: 'clock-freq-min-max' property was deprecated.
  622. [   21.159060] dwmmc_rockchip fe320000.dwmmc: No vmmc regulator found
  623. [   21.159545] sdhci-pltfm: SDHCI platform and OF driver helper
  624. [   21.161535] sdhci-arasan fe330000.sdhci: No vmmc regulator found
  625. [   21.161550] sdhci-arasan fe330000.sdhci: No vqmmc regulator found
  626. [   21.189975] mmc0: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA
  627. [   21.193827] hidraw: raw HID events driver (C) Jiri Kosina
  628. [   21.201698] input: Lite-On Technology Corp. USB Keyboard as /devices/platform/fe3c0000.usb/usb1/1-1/1-1.4/1-1.4:1.0/0003:04CA:004B.0001/input/input1
  629. [   21.231257] mmc0: MAN_BKOPS_EN bit is not set
  630. [   21.246407] mmc0: new HS400 Enhanced strobe MMC card at address 0001
  631. [   21.247819] mmcblk0: mmc0:0001 AJTD4R 14.6 GiB
  632. [   21.249149] mmcblk0boot0: mmc0:0001 AJTD4R partition 1 4.00 MiB
  633. [   21.250699] mmcblk0boot1: mmc0:0001 AJTD4R partition 2 4.00 MiB
  634. [   21.251945] mmcblk0rpmb: mmc0:0001 AJTD4R partition 3 4.00 MiB
  635. [   21.253069] rkpart: partition size too small (0)
  636. [   21.253096]      uboot: 0x000400000 -- 0x000800000 (4 MB)
  637. [   21.253109]      trust: 0x000800000 -- 0x000c00000 (4 MB)
  638. [   21.253121]       misc: 0x000c00000 -- 0x001000000 (4 MB)
  639. [   21.253132]   resource: 0x001000000 -- 0x002000000 (16 MB)
  640. [   21.253144]     kernel: 0x002000000 -- 0x003800000 (24 MB)
  641. [   21.253156]       boot: 0x003800000 -- 0x005800000 (32 MB)
  642. [   21.253167]   recovery: 0x005800000 -- 0x007800000 (32 MB)
  643. [   21.253230]     backup: 0x007800000 -- 0x00e800000 (112 MB)

复制代码

作者: jpchen    时间: 2020-2-21 16:48
Hi ,you can use the AndroidTool2.63 version to download firmware.
link : https://drive.google.com/open?id ... P0JOlVWG05rJ9_gJ449
作者: kannant    时间: 2020-2-26 13:41
after flashing using android 2.63 tool i am facing the same issue




欢迎光临 Firefly开源社区 (https://dev.t-firefly.com/) Powered by Discuz! X3.1