Firefly开源社区

标题: 不能起动 [打印本页]
作者: keithc    时间: 2020-7-27 15:53
标题: 不能起动
本帖最后由 keithc 于 2020-7-27 15:54 编辑

自已打版，并用 ROC-RK3308-CC_Buildroot_normal_20181114.img 镜像， 有以下的 讯息， 之後一直就在这里，请帮忙…

  1. pwm-regulator(vdd-core): init 1044000 uV
  2. regulator(vdd-core) init 1044000 uV
  3. MMC:   dwmmc@ff490000: 0
  4. Using default environment

  6. In:    serial@ff0c0000
  7. Out:   serial@ff0c0000
  8. Err:   serial@ff0c0000
  9. Model: Rockchip RK3308 EVB
  10. MMC Device 1 not found
  11. no mmc device at slot 1
  12. switch to partitions #0, OK
  13. mmc0(part 0) is current device
  14. enter Recovery mode!
  15. CLK:
  16. apll 816000 KHz
  17. dpll 1300000 KHz
  18. vpll0 1179647 KHz
  19. vpll1 903167 KHz
  20. aclk_bus 185714 KHz
  21. hclk_bus 100000 KHz
  22. pclk_bus 100000 KHz
  23. aclk_peri 185714 KHz
  24. hclk_peri 100000 KHz
  25. pclk_peri 100000 KHz
  26. hclk_audio 98303 KHz
  27. pclk_audio 98303 KHz
  28. Net:   Net Initialization Skipped
  29. No ethernet found.
  30. Hit any key to stop autoboot:  0
  31. ANDROID: reboot reason: "recovery"
  32. FDT load addr 0x10f00000 size 253 KiB
  33. Booting kernel at 0x4080000 with fdt at 4acb000...


  36. ## Booting Android Image at 0x04080000 ...
  37. Kernel load addr 0x02080000 size 4635 KiB
  38. RAM disk load addr 0x11000000 size 5900 KiB
  39. ## Flattened Device Tree blob at 04acb000
  40.    Booting using the fdt blob at 0x4acb000
  41.    Uncompressing Kernel Image ... OK
  42.    Loading Ramdisk to 0ef51000, end 0f513eff ... OK
  43.    Loading Device Tree to 000000000ef3d000, end 000000000ef50205 ... OK
  44. Adding bank: start=0x00200000, size=0x0fe00000

  46. Starting kernel ...


  49. [    0.000000] Booting Linux on physical CPU 0x0
  50. [    0.000000] Linux version 4.4.143 (guanzl@mid-server) (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05) ) #1 SMP PREEMPT Tue Nov 13 10:30:07 CST 2018
  51. [    0.000000] Boot CPU: AArch64 Processor [410fd042]
  52. [    0.000000] earlycon: Early serial console at MMIO32 0xff0c0000 (options '')
  53. [    0.000000] bootconsole [uart0] enabled
  54. [    0.000000] Reserved memory: failed to reserve memory for node 'drm-logo@00000000': base 0x0000000000000000, size 0 MiB
  55. [    0.000000] psci: probing for conduit method from DT.
  56. [    0.000000] psci: PSCIv1.0 detected in firmware.
  57. [    0.000000] psci: Using standard PSCI v0.2 function IDs
  58. [    0.000000] psci: MIGRATE_INFO_TYPE not supported.
  59. [    0.000000] PERCPU: Embedded 19 pages/cpu @ffffffc00ff54000 s40088 r8192 d29544 u77824
  60. [    0.000000] Detected VIPT I-cache on CPU0
  61. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64008
  62. [    0.000000] Kernel command line: storagemedia=emmc androidboot.mode=emmc androidboot.slot_suffix= androidboot.serialno=c3d9b8674f4b94f6  rootwait earlycon=uart8250,mmio32,0xff0c0000 swiotlb=1 console=ttyFIQ0 root=PARTUUID=614e0000-0000 rootfstype=squashfs snd_aloop.index=7
  63. [    0.000000] PID hash table entries: 1024 (order: 1, 8192 bytes)
  64. [    0.000000] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
  65. [    0.000000] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
  66. [    0.000000] software IO TLB [mem 0x0feb4000-0x0fef4000] (0MB) mapped at [ffffffc00feb4000-ffffffc00fef3fff]
  67. [    0.000000] Memory: 239396K/260096K available (5758K kernel code, 418K rwdata, 2112K rodata, 384K init, 502K bss, 20700K reserved, 0K cma-reserved)
  68. [    0.000000] Virtual kernel memory layout:
  69. [    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
  70. [    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000   (   246 GB)
  71. [    0.000000]       .init : 0xffffff8008840000 - 0xffffff80088a0000   (   384 KB)
  72. [    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008620000   (  5760 KB)
  73. [    0.000000]     .rodata : 0xffffff8008620000 - 0xffffff8008840000   (  2176 KB)
  74. [    0.000000]       .data : 0xffffff80088a0000 - 0xffffff8008908808   (   419 KB)
  75. [    0.000000]     fixed   : 0xffffffbffe7fd000 - 0xffffffbffec00000   (  4108 KB)
  76. [    0.000000]     PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000   (    16 MB)
  77. [    0.000000]     memory  : 0xffffffc000200000 - 0xffffffc010000000   (   254 MB)
  78. [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
  79. [    0.000000] Preemptible hierarchical RCU implementation.
  80. [    0.000000]  Build-time adjustment of leaf fanout to 64.
  81. [    0.000000] NR_IRQS:64 nr_irqs:64 0
  82. [    0.000000] GIC: Using split EOI/Deactivate mode
  83. [    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
  84. [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
  85. [    0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
  86. [    0.001756] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=24000)
  87. [    0.002706] pid_max: default: 32768 minimum: 301
  88. [    0.003258] Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
  89. [    0.003860] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes)
  90. [    0.005289] sched-energy: CPU device node has no sched-energy-costs
  91. [    0.005907] Invalid sched_group_energy for CPU0
  92. [    0.006326] CPU0: update cpu_capacity 1024
  93. [    0.006750] ASID allocator initialised with 65536 entries
  94. [    0.016479] Detected VIPT I-cache on CPU1
  95. [    0.016534] Invalid sched_group_energy for CPU1
  96. [    0.016540] CPU1: update cpu_capacity 1024
  97. [    0.016544] CPU1: Booted secondary processor [410fd042]
  98. [    0.019500] Detected VIPT I-cache on CPU2
  99. [    0.019538] Invalid sched_group_energy for CPU2
  100. [    0.019542] CPU2: update cpu_capacity 1024
  101. [    0.019546] CPU2: Booted secondary processor [410fd042]
  102. [    0.022542] Detected VIPT I-cache on CPU3
  103. [    0.022577] Invalid sched_group_energy for CPU3
  104. [    0.022582] CPU3: update cpu_capacity 1024
  105. [    0.022586] CPU3: Booted secondary processor [410fd042]
  106. [    0.022654] Brought up 4 CPUs
  107. [    0.027858] SMP: Total of 4 processors activated.
  108. [    0.028297] CPU: All CPU(s) started at EL2
  109. [    0.028814] Invalid sched_group_energy for CPU3
  110. [    0.029236] Invalid sched_group_energy for Cluster3
  111. [    0.029698] Invalid sched_group_energy for CPU2
  112. [    0.030116] Invalid sched_group_energy for Cluster2
  113. [    0.030564] Invalid sched_group_energy for CPU1
  114. [    0.030991] Invalid sched_group_energy for Cluster1
  115. [    0.031440] Invalid sched_group_energy for CPU0
  116. [    0.031856] Invalid sched_group_energy for Cluster0
  117. [    0.032821] devtmpfs: initialized
  118. [    0.050982] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
  119. [    0.051920] futex hash table entries: 1024 (order: 4, 65536 bytes)
  120. [    0.052884] pinctrl core: initialized pinctrl subsystem
  121. [    0.054474] NET: Registered protocol family 16
  122. [    0.059478] cpuidle: using governor menu
  123. [    0.059870] Registered FIQ tty driver
  124. [    0.060552] vdso: 2 pages (1 code @ ffffff8008626000, 1 data @ ffffff80088a4000)
  125. [    0.061260] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
  126. [    0.062092] DMA: preallocated 256 KiB pool for atomic allocations
  127. [    0.065561] console [pstore-1] enabled
  128. [    0.065913] pstore: Registered ramoops as persistent store backend
  129. [    0.066498] ramoops: attached 0xf0000@0x110000, ecc: 0/0
  130. [    0.084998] fiq debugger fiq mode enabled
  131. [[    0.085747] console [ttyFIQ0] enabled
  132.     0.085747] console [ttyFIQ0] enabled
  133. [    0.086444] bootconsole [uart0] disabled
  134. [    0.086444] bootconsole [uart0] disabled
  135. [    0.087057] Registered fiq debugger ttyFIQ0
  136. WARNING: suspend_mode_handler: Not support call: 0x4
  137. [    0.101845] vcc_1v8: regulator get failed, ret=-517
  138. [    0.102691] vcc_1v8_codec: regulator get failed, ret=-517
  139. [    0.103481] vcc_1v8: supplied by vcc_io
  140. [    0.103571] vcc_1v8_codec: supplied by vcc_io
  141. [    0.105977] SCSI subsystem initialized
  142. [    0.106276] usbcore: registered new interface driver usbfs
  143. [    0.106353] usbcore: registered new interface driver hub
  144. [    0.106480] usbcore: registered new device driver usb
  145. [    0.106622] pps_core: LinuxPPS API ver. 1 registered
  146. [    0.106636] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  147. [    0.106672] PTP clock support registered
  148. [    0.107866] Advanced Linux Sound Architecture Driver Initialized.
  149. [    0.108534] Bluetooth: Core ver 2.21
  150. [    0.108596] NET: Registered protocol family 31
  151. [    0.108609] Bluetooth: HCI device and connection manager initialized
  152. [    0.108630] Bluetooth: HCI socket layer initialized
  153. [    0.108646] Bluetooth: L2CAP socket layer initialized
  154. [    0.108686] Bluetooth: SCO socket layer initialized
  155. [    0.109819] rockchip-cpuinfo cpuinfo: Serial         : a32b06ea995d4011
  156. [    0.110487] clocksource: Switched to clocksource arch_sys_counter
  157. [    0.112960] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
  158. [    0.113255] NET: Registered protocol family 2
  159. [    0.113957] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
  160. [    0.114018] TCP bind hash table entries: 2048 (order: 3, 32768 bytes)
  161. [    0.114079] TCP: Hash tables configured (established 2048 bind 2048)
  162. [    0.114161] UDP hash table entries: 256 (order: 1, 8192 bytes)
  163. [    0.114192] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
  164. [    0.114411] NET: Registered protocol family 1
  165. [    0.114738] Unpacking initramfs...
  166. [    0.558239] Freeing initrd memory: 5896K
  167. [    0.558926] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
  168. [    0.570326] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  169. [    0.570643] ntfs: driver 2.1.32 [Flags: R/W].
  170. [    0.573977] io scheduler noop registered (default)
  171. [    0.575124] phy phy-ff008000.syscon:usb2-phy@100.0: Failed to get VBUS supply regulator
  172. [    0.579445] dma-pl330 ff2c0000.dma-controller: Loaded driver for PL330 DMAC-241330
  173. [    0.579504] dma-pl330 ff2c0000.dma-controller:       DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
  174. [    0.581926] dma-pl330 ff2d0000.dma-controller: Loaded driver for PL330 DMAC-241330
  175. [    0.581964] dma-pl330 ff2d0000.dma-controller:       DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
  176. [    0.582314] rockchip-pvtm ff000000.grf:pmu-pvtm: failed to get rst 0 pmu
  177. [    0.582462] rockchip-pvtm ff00c000.syscon:pvtm: failed to get rst 0 core
  178. [    0.584016] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled
  179. [    0.586313] ff0e0000.serial: ttyS4 at MMIO 0xff0e0000 (irq = 12, base_baud = 6770833) is a 16550A
  180. [    0.588167] [drm] Initialized drm 1.1.0 20060810
  181. [    0.588334] random: nonblocking pool is initialized
  182. [    0.591082] Unable to detect cache hierarchy for CPU 0
  183. [    0.598094] loop: module loaded
  184. [    0.598463] SCSI Media Changer driver v0.25
  185. [    0.600412] rk_gmac-dwmac ff4e0000.ethernet: clock input or output? (input).
  186. [    0.600459] rk_gmac-dwmac ff4e0000.ethernet: Can not read property: tx_delay.
  187. [    0.600504] rk_gmac-dwmac ff4e0000.ethernet: set tx_delay to 0x30
  188. [    0.600527] rk_gmac-dwmac ff4e0000.ethernet: Can not read property: rx_delay.
  189. [    0.600543] rk_gmac-dwmac ff4e0000.ethernet: set rx_delay to 0x10
  190. [    0.600566] rk_gmac-dwmac ff4e0000.ethernet: integrated PHY? (no).
  191. [    0.600807] rk_gmac-dwmac ff4e0000.ethernet: clock input from PHY
  192. [    0.605841] rk_gmac-dwmac ff4e0000.ethernet: init for RMII
  193. [    0.605980] stmmac - user ID: 0x10, Synopsys ID: 0x35
  194. [    0.605996]  Ring mode enabled
  195. [    0.606008]  DMA HW capability register supported
  196. [    0.606016]  Normal descriptors
  197. [    0.606028]  RX Checksum Offload Engine supported (type 2)
  198. [    0.606038]  TX Checksum insertion supported
  199. [    0.606048]  Wake-Up On Lan supported
  200. [    0.606108]  Enable RX Mitigation via HW Watchdog Timer
  201. [    0.689773] libphy: stmmac: probed
  202. [    0.689815] eth%d: PHY ID 0000ffff at 0 IRQ POLL (stmmac-0:00) active
  203. [    0.689832] eth%d: PHY ID 0000ffff at 1 IRQ POLL (stmmac-0:01)
  204. [    0.689845] eth%d: PHY ID 0000ffff at 2 IRQ POLL (stmmac-0:02)
  205. [    0.689858] eth%d: PHY ID 0000ffff at 3 IRQ POLL (stmmac-0:03)
  206. [    0.689871] eth%d: PHY ID 0000ffff at 4 IRQ POLL (stmmac-0:04)
  207. [    0.689884] eth%d: PHY ID 0000ffff at 5 IRQ POLL (stmmac-0:05)
  208. [    0.689897] eth%d: PHY ID 0000ffff at 6 IRQ POLL (stmmac-0:06)
  209. [    0.689910] eth%d: PHY ID 0000ffff at 7 IRQ POLL (stmmac-0:07)
  210. [    0.689923] eth%d: PHY ID 0000ffff at 8 IRQ POLL (stmmac-0:08)
  211. [    0.689937] eth%d: PHY ID 0000ffff at 9 IRQ POLL (stmmac-0:09)
  212. [    0.689950] eth%d: PHY ID 0000ffff at 10 IRQ POLL (stmmac-0:0a)
  213. [    0.689963] eth%d: PHY ID 0000ffff at 11 IRQ POLL (stmmac-0:0b)
  214. [    0.689976] eth%d: PHY ID 0000ffff at 12 IRQ POLL (stmmac-0:0c)
  215. [    0.689989] eth%d: PHY ID 0000ffff at 13 IRQ POLL (stmmac-0:0d)
  216. [    0.690002] eth%d: PHY ID 0000ffff at 14 IRQ POLL (stmmac-0:0e)
  217. [    0.690015] eth%d: PHY ID 0000ffff at 15 IRQ POLL (stmmac-0:0f)
  218. [    0.690029] eth%d: PHY ID 0000ffff at 16 IRQ POLL (stmmac-0:10)
  219. [    0.690047] eth%d: PHY ID 0000ffff at 17 IRQ POLL (stmmac-0:11)
  220. [    0.690060] eth%d: PHY ID 0000ffff at 18 IRQ POLL (stmmac-0:12)
  221. [    0.690073] eth%d: PHY ID 0000ffff at 19 IRQ POLL (stmmac-0:13)
  222. [    0.690086] eth%d: PHY ID 0000ffff at 20 IRQ POLL (stmmac-0:14)
  223. [    0.690099] eth%d: PHY ID 0000ffff at 21 IRQ POLL (stmmac-0:15)
  224. [    0.690113] eth%d: PHY ID 0000ffff at 22 IRQ POLL (stmmac-0:16)
  225. [    0.690126] eth%d: PHY ID 0000ffff at 23 IRQ POLL (stmmac-0:17)
  226. [    0.690139] eth%d: PHY ID 0000ffff at 24 IRQ POLL (stmmac-0:18)
  227. [    0.690152] eth%d: PHY ID 0000ffff at 25 IRQ POLL (stmmac-0:19)
  228. [    0.690165] eth%d: PHY ID 0000ffff at 26 IRQ POLL (stmmac-0:1a)
  229. [    0.690178] eth%d: PHY ID 0000ffff at 27 IRQ POLL (stmmac-0:1b)
  230. [    0.690191] eth%d: PHY ID 0000ffff at 28 IRQ POLL (stmmac-0:1c)
  231. [    0.690204] eth%d: PHY ID 0000ffff at 29 IRQ POLL (stmmac-0:1d)
  232. [    0.690216] eth%d: PHY ID 0000ffff at 30 IRQ POLL (stmmac-0:1e)
  233. [    0.690229] eth%d: PHY ID 0000ffff at 31 IRQ POLL (stmmac-0:1f)
  234. [    0.691434] Rockchip WiFi SYS interface (V1.00) ...
  235. [    0.691940] ff400000.usb supply vusb_d not found, using dummy regulator
  236. [    0.692033] ff400000.usb supply vusb_a not found, using dummy regulator
  237. [    0.804558] dwc2 ff400000.usb: EPs: 10, dedicated fifos, 972 entries in SPRAM
  238. [    0.805091] dwc2 ff400000.usb: DWC OTG Controller
  239. [    0.805142] dwc2 ff400000.usb: new USB bus registered, assigned bus number 1
  240. [    0.805193] dwc2 ff400000.usb: irq 22, io mem 0xff400000
  241. [    0.806285] hub 1-0:1.0: USB hub found
  242. [    0.806355] hub 1-0:1.0: 1 port detected
  243. [    0.807279] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  244. [    0.807313] ehci-platform: EHCI generic platform driver
  245. [    0.811142] ehci-platform ff440000.usb: EHCI Host Controller
  246. [    0.811194] ehci-platform ff440000.usb: new USB bus registered, assigned bus number 2
  247. [    0.811341] ehci-platform ff440000.usb: irq 23, io mem 0xff440000
  248. [    0.816518] ehci-platform ff440000.usb: USB 2.0 started, EHCI 1.00
  249. [    0.817557] hub 2-0:1.0: USB hub found
  250. [    0.817615] hub 2-0:1.0: 1 port detected
  251. [    0.818195] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  252. [    0.818246] ohci-platform: OHCI generic platform driver
  253. [    0.818667] ohci-platform ff450000.usb: Generic Platform OHCI controller
  254. [    0.818713] ohci-platform ff450000.usb: new USB bus registered, assigned bus number 3
  255. [    0.818894] ohci-platform ff450000.usb: irq 24, io mem 0xff450000
  256. [    0.874367] hub 3-0:1.0: USB hub found
  257. [    0.874424] hub 3-0:1.0: 1 port detected
  258. [    0.875090] usbcore: registered new interface driver uas
  259. [    0.875239] usbcore: registered new interface driver usb-storage
  260. [    0.875300] usbcore: registered new interface driver ums-alauda
  261. [    0.875366] usbcore: registered new interface driver ums-cypress
  262. [    0.875429] usbcore: registered new interface driver ums-datafab
  263. [    0.875516] usbcore: registered new interface driver ums_eneub6250
  264. [    0.875584] usbcore: registered new interface driver ums-freecom
  265. [    0.875650] usbcore: registered new interface driver ums-isd200
  266. [    0.875708] usbcore: registered new interface driver ums-jumpshot
  267. [    0.875769] usbcore: registered new interface driver ums-karma
  268. [    0.875838] usbcore: registered new interface driver ums-onetouch
  269. [    0.875900] usbcore: registered new interface driver ums-sddr09
  270. [    0.875961] usbcore: registered new interface driver ums-sddr55
  271. [    0.876027] usbcore: registered new interface driver ums-usbat
  272. [    0.876773] i2c /dev entries driver
  273. [    0.877913] rk3x-i2c ff050000.i2c: Initialized RK3xxx I2C bus at ffffff80089be000
  274. [    0.880695] rk_tsadcv2_temp_to_code: Invalid conversion table: code=4095, temperature=2147483647
  275. [    0.880941] rockchip-thermal ff1f0000.tsadc: tsadc is probed successfully!
  276. [    0.881581] Bluetooth: HCI UART driver ver 2.3
  277. [    0.881607] Bluetooth: HCI UART protocol H4 registered
  278. [    0.881618] Bluetooth: HCI UART protocol LL registered
  279. [    0.881856] cpu cpu0: leakage=13
  280. [    0.882115] cpu cpu0: Failed to get pvtm
  281. [    0.884753] Synopsys Designware Multimedia Card Interface Driver
  282. [    0.886446] dwmmc_rockchip ff480000.dwmmc: num-slots property not found, assuming 1 slot is available
  283. [    0.886626] dwmmc_rockchip ff480000.dwmmc: IDMAC supports 32-bit address mode.
  284. [    0.886678] dwmmc_rockchip ff480000.dwmmc: Using internal DMA controller.
  285. [    0.886702] dwmmc_rockchip ff480000.dwmmc: Version ID is 270a
  286. [    0.886779] dwmmc_rockchip ff480000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo
  287. [    0.887590] rockchip-iodomain ff000000.grf:io-domains: Setting to 3300000 done
  288. [    0.887628] rockchip-iodomain ff000000.grf:io-domains: Setting to 3300000 done
  289. [    0.898582] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
  290. [    0.909659] rockchip-iodomain ff000000.grf:io-domains: Setting to 3300000 done
  291. [    0.909694] rockchip-iodomain ff000000.grf:io-domains: Setting to 3300000 done
  292. [    0.909707] set vqmmc to 3.3v, ret=0
  293. [    0.910223] dwmmc_rockchip ff480000.dwmmc: 1 slots initialized
  294. [    0.910459] dwmmc_rockchip ff490000.dwmmc: No default pinctrl state
  295. [    0.910518] dwmmc_rockchip ff490000.dwmmc: No off pinctrl state
  296. [    0.910646] dwmmc_rockchip ff490000.dwmmc: IDMAC supports 32-bit address mode.
  297. [    0.910697] dwmmc_rockchip ff490000.dwmmc: Using internal DMA controller.
  298. [    0.910722] dwmmc_rockchip ff490000.dwmmc: Version ID is 270a
  299. [    0.910798] dwmmc_rockchip ff490000.dwmmc: DW MMC controller at irq 26,32 bit host data width,256 deep fifo
  300. [    0.910877] dwmmc_rockchip ff490000.dwmmc: No vmmc regulator found
  301. [    0.910894] dwmmc_rockchip ff490000.dwmmc: No vqmmc regulator found
  302. [    0.921658] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
  303. [    0.932683] dwmmc_rockchip ff490000.dwmmc: 1 slots initialized
  304. [    0.933261] dwmmc_rockchip ff4a0000.dwmmc: No default pinctrl state
  305. [    0.933284] dwmmc_rockchip ff4a0000.dwmmc: No off pinctrl state
  306. [    0.933302] dwmmc_rockchip ff4a0000.dwmmc: num-slots property not found, assuming 1 slot is available
  307. [    0.933398] dwmmc_rockchip ff4a0000.dwmmc: IDMAC supports 32-bit address mode.
  308. [    0.933435] dwmmc_rockchip ff4a0000.dwmmc: Using internal DMA controller.
  309. [    0.933454] dwmmc_rockchip ff4a0000.dwmmc: Version ID is 270a
  310. [    0.933541] dwmmc_rockchip ff4a0000.dwmmc: DW MMC controller at irq 27,32 bit host data width,256 deep fifo
  311. [    0.933601] dwmmc_rockchip ff4a0000.dwmmc: No vmmc regulator found
  312. [    0.933615] dwmmc_rockchip ff4a0000.dwmmc: No vqmmc regulator found
  313. [    0.933911] dwmmc_rockchip ff4a0000.dwmmc: allocated mmc-pwrseq
  314. [    0.944624] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
  315. [    0.955637] dwmmc_rockchip ff4a0000.dwmmc: 1 slots initialized
  316. [    0.957045] is31fl32xx 1-003c: register write to 0x00 failed (error -6),val=0
  317. [    0.968375] mmc1: MAN_BKOPS_EN bit is not set
  318. [    0.971807] mmc_host mmc1: Bus speed (slot 0) = 147456000Hz (slot req 150000000Hz, actual 147456000HZ div = 0)
  319. [    0.980598] mmc_host mmc2: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
  320. [    0.988665] phy phy-ff008000.syscon:usb2-phy@100.0: charger = USB_CDP_CHARGER
  321. [    1.017579] mmc_host mmc2: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0)
  322. [    1.057701] is31fl32xx 1-003c: register write to 0x00 failed (error -6),val=0
  323. [    1.058571] mmc_host mmc2: Bus speed (slot 0) = 100000Hz (slot req 100000Hz, actual 100000HZ div = 0)
  324. [    1.158682] is31fl32xx 1-003c: register write to 0x00 failed (error -6),val=0
  325. [    1.259645] is31fl32xx_init_regs, write to shutdown register failed
  326. [    1.259770] is31fl32xx 1-003c: register write to 0x26 failed (error -6),val=1
  327. [    1.348282] dwmmc_rockchip ff490000.dwmmc: Successfully tuned phase to 60
  328. [    1.348437] mmc1: new HS200 MMC card at address 0001
  329. [    1.349900] mmcblk1: mmc1:0001 8GTF4R 7.28 GiB
  330. [    1.350688] mmcblk1boot0: mmc1:0001 8GTF4R partition 1 4.00 MiB
  331. [    1.352602] mmcblk1boot1: mmc1:0001 8GTF4R partition 2 4.00 M[    1.359059]  mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8
  332. [    1.360681] is31fl32xx 1-003c: register write to 0x26 failed (error -6),val=1
  333. [    1.461771] is31fl32xx 1-003c: register write to 0x26 failed (error -6),val=1
  334. [    1.563239] usbcore: registered new interface driver usbhid
  335. [    1.563286] usbhid: USB HID core driver
  336. [    1.563585] rockchip-dmc dmc: failed to get the count of devfreq-event in /dmc node
  337. [    1.563993] rockchip-dmc dmc: Failed to get leakage
  338. [    1.564160] rockchip-dmc dmc: Failed to get pvtm
  339. [    1.564751] rockchip-dmc dmc: failed to get vop bandwidth to dmc rate
  340. [    [    1.568660] rknandc_base v1.1 2017-01-11
  341. [    1.569126] rksfc_base v1.1 2016-01-08
  342. [    1.577751] rk3308-acodec ff560000.acodec: Don't need pa-drv gpio
  343. [    1.577808] rk3308-acodec ff560000.acodec: De-pop as much as possible
  344. [    1.578946] 1-001a supply AVDD not found, using dummy regulator
  345. [    1.579092] 1-001a supply DVDD not found, using dummy regulator
  346. [    1.579206] 1-001a supply PVDD_A not found, using dummy regulator
  347. [    1.579318] 1-001a supply PVDD_001a supply PVDD_C not found, using dummy regulator
  348. [    1.5796ror requesting pdn_gpio: -16
  349. [    1.580683] tas571x: probe of 1-001a failed with error -16
  350. [    1.589346] rk-multicodecs bluetooth-sound: card: 0 has not been locked, re-probe again
  351. [    1.589420] rk-multicodecs bluetooth-sound: check_lock_card failed: -517
  352. [    1.589965] rk-multicodecs vad-sound: ASoC: CPU DAI (null) not registered
  353. [    1.591439] NET: Registered protocol family 10
  354. [    1.592852] NET: Registered protocol family 17
  355. [    1.592922] NET: Registered protocol family 15
  356. [    1.593192] Bluetooth: RFCOMM TTY layer initialized
  357. [    1.593217] Bluetooth: RFCOMM socket layer initialized
  358. [    1.593255] Bluetooth: RFCOMM ver 1.11
  359. [    1.593280] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  360. [    1.593297] Bluetooth: HIDP socket layer initialized
  361. [    1.593312] [WLAN_RFKILL]: Enter rfkill_wlan_init
  362. [    1.593868] [WLAN_RFKILL]: Enter rfkill_wlan_probe
  363. [    1.593897] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6236
  364. [    1.593914] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
  365. [    1.593923] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
  366. [    1.594007] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 0, flags = 1.
  367. [    1.594023] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
  368. [    1.594032] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
  369. [    1.594044] [WLAN_RFKILL]: Exit rfkill_wlan_probe
  370. [    1.594123] [BT_RFKILL]: Enter rfkill_rk_init
  371. [    1.594594] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 135.
  372. [    1.594635] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,power_gpio = 139.
  373. [    1.594685] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 140.
  374. [    1.594697] [BT_RFKILL]: bluetooth_platdata_parse_dt: clk_get failed!!!.
  375. [    1.594766] [BT_RFKILL]: Request irq for bt wakeup host
  376. [    1.594826] [BT_RFKILL]: ** disable irq
  377. [    1.595005] [BT_RFKILL]: bt_default device registered.
  378. [    1.595549] flash vendor_init_thread!
  379. [    1.595576] flash vendor storage:20170308 ret = -1
  380. [    1.596596] vendor storage:20160801 ret = 0
  381. [    1.597968] input: adc-keys as /devices/platform/adc-keys/input/input0
  382. [    1.599212] rk-multicodecs bluetooth-sound: card: 0 has not been locked, re-probe again
  383. [    1.599245] rk-multicodecs bluetooth-sound: check_lock_card failed: -517
  384. [    1.671208] rk-multicodecs vad-sound: multicodec <-> pdm-i2s-dais mapping ok
  385. [    1.674539] rk-multicodecs bluetooth-sound: dummy_codec <-> ff350000.i2s mapping ok
  386. [    1.676041] dhd_module_init: in Dongle Host Driver, version 1.579.77.41.2 (r)
  387. [    1.676070] ======== dhd_wlan_init_plat_data ========
  388. [    1.676081] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
  389. [    1.676090] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
  390. [    1.676101] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter
  391. [    1.676114] dhd_wlan_init_gpio: host_oob_irq: 36
  392. [    1.676123] dhd_wlan_init_gpio: host_oob_irq_flags=0x418
  393. [    1.676132] dhd_wifi_platform_load: Enter
  394. [    1.676163] Power-up adapter 'DHD generic adapter'
  395. [    1.676219] wifi_platform_set_power = 1
  396. [    1.676228] ======== PULL WL_REG_ON(-1) HIGH! ========
  397. [    1.676238] [WLAN_RFKILL]: rockchip_wifi_power: 1
  398. [    1.676248] [WLAN_RFKILL]: wifi turn on power. -1
  399. [    1.676311] hctosys: unable to open rtc device (rtc0)
  400. [    1.688011] vcc_sd: disabling
  401. [    1.688066] vccio_sd: disabling
  402. u▒   1.688696]
  403. pwm-regulator(vdd-core): init 1044000 uV
  404. regulator(vdd-core) init 1044000 uV
  405. MMC:   dwmmc@ff490000: 0
  406. Using default environment

  408. In:    serial@ff0c0000
  409. Out:   serial@ff0c0000
  410. Err:   serial@ff0c0000
  411. Model: Rockchip RK3308 EVB
  412. MMC Device 1 not found
  413. no mmc device at slot 1
  414. switch to partitions #0, OK
  415. mmc0(part 0) is current device
  416. enter Recovery mode!
  417. CLK:
  418. apll 816000 KHz
  419. dpll 1300000 KHz
  420. vpll0 1179647 KHz
  421. vpll1 903167 KHz
  422. aclk_bus 185714 KHz
  423. hclk_bus 100000 KHz
  424. pclk_bus 100000 KHz
  425. aclk_peri 185714 KHz
  426. hclk_peri 100000 KHz
  427. pclk_peri 100000 KHz
  428. hclk_audio 98303 KHz
  429. pclk_audio 98303 KHz
  430. Net:   Net Initialization Skipped
  431. No ethernet found.
  432. Hit any key to stop autoboot:  0
  433. ANDROID: reboot reason: "recovery"
  434. FDT load addr 0x10f00000 size 253 KiB
  435. Booting kernel at 0x4080000 with fdt at 4acb000...


  438. ## Booting Android Image at 0x04080000 ...
  439. Kernel load addr 0x02080000 size 4635 KiB
  440. RAM disk load addr 0x11000000 size 5900 KiB
  441. ## Flattened Device Tree blob at 04acb000
  442.    Booting using the fdt blob at 0x4acb000
  443.    Uncompressing Kernel Image ... OK
  444.    Loading Ramdisk to 0ef51000, end 0f513eff ... OK
  445.    Loading Device Tree to 000000000ef3d000, end 000000000ef50205 ... OK
  446. Adding bank: start=0x00200000, size=0x0fe00000

  448. Starting kernel ...


  451. [    0.000000] Booting Linux on physical CPU 0x0
  452. [    0.000000] Linux version 4.4.143 (guanzl@mid-server) (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05) ) #1 SMP PREEMPT Tue Nov 13 10:30:07 CST 2018
  453. [    0.000000] Boot CPU: AArch64 Processor [410fd042]
  454. [    0.000000] earlycon: Early serial console at MMIO32 0xff0c0000 (options '')
  455. [    0.000000] bootconsole [uart0] enabled
  456. [    0.000000] Reserved memory: failed to reserve memory for node 'drm-logo@00000000': base 0x0000000000000000, size 0 MiB
  457. [    0.000000] psci: probing for conduit method from DT.
  458. [    0.000000] psci: PSCIv1.0 detected in firmware.
  459. [    0.000000] psci: Using standard PSCI v0.2 function IDs
  460. [    0.000000] psci: MIGRATE_INFO_TYPE not supported.
  461. [    0.000000] PERCPU: Embedded 19 pages/cpu @ffffffc00ff54000 s40088 r8192 d29544 u77824
  462. [    0.000000] Detected VIPT I-cache on CPU0
  463. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64008
  464. [    0.000000] Kernel command line: storagemedia=emmc androidboot.mode=emmc androidboot.slot_suffix= androidboot.serialno=c3d9b8674f4b94f6  rootwait earlycon=uart8250,mmio32,0xff0c0000 swiotlb=1 console=ttyFIQ0 root=PARTUUID=614e0000-0000 rootfstype=squashfs snd_aloop.index=7
  465. [    0.000000] PID hash table entries: 1024 (order: 1, 8192 bytes)
  466. [    0.000000] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
  467. [    0.000000] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
  468. [    0.000000] software IO TLB [mem 0x0feb4000-0x0fef4000] (0MB) mapped at [ffffffc00feb4000-ffffffc00fef3fff]
  469. [    0.000000] Memory: 239396K/260096K available (5758K kernel code, 418K rwdata, 2112K rodata, 384K init, 502K bss, 20700K reserved, 0K cma-reserved)
  470. [    0.000000] Virtual kernel memory layout:
  471. [    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
  472. [    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000   (   246 GB)
  473. [    0.000000]       .init : 0xffffff8008840000 - 0xffffff80088a0000   (   384 KB)
  474. [    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008620000   (  5760 KB)
  475. [    0.000000]     .rodata : 0xffffff8008620000 - 0xffffff8008840000   (  2176 KB)
  476. [    0.000000]       .data : 0xffffff80088a0000 - 0xffffff8008908808   (   419 KB)
  477. [    0.000000]     fixed   : 0xffffffbffe7fd000 - 0xffffffbffec00000   (  4108 KB)
  478. [    0.000000]     PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000   (    16 MB)
  479. [    0.000000]     memory  : 0xffffffc000200000 - 0xffffffc010000000   (   254 MB)
  480. [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
  481. [    0.000000] Preemptible hierarchical RCU implementation.
  482. [    0.000000]  Build-time adjustment of leaf fanout to 64.
  483. [    0.000000] NR_IRQS:64 nr_irqs:64 0
  484. [    0.000000] GIC: Using split EOI/Deactivate mode
  485. [    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
  486. [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
  487. [    0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
  488. [    0.001746] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=24000)
  489. [    0.002696] pid_max: default: 32768 minimum: 301
  490. [    0.003247] Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
  491. [    0.003849] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes)
  492. [    0.005268] sched-energy: CPU device node has no sched-energy-costs
  493. [    0.005885] Invalid sched_group_energy for CPU0
  494. [    0.006304] CPU0: update cpu_capacity 1024
  495. [    0.006727] ASID allocator initialised with 65536 entries
  496. [    0.016458] Detected VIPT I-cache on CPU1
  497. [    0.016514] Invalid sched_group_energy for CPU1
  498. [    0.016519] CPU1: update cpu_capacity 1024
  499. [    0.016524] CPU1: Booted secondary processor [410fd042]
  500. [    0.019479] Detected VIPT I-cache on CPU2
  501. [    0.019515] Invalid sched_group_energy for CPU2
  502. [    0.019519] CPU2: update cpu_capacity 1024
  503. [    0.019523] CPU2: Booted secondary processor [410fd042]
  504. [    0.022521] Detected VIPT I-cache on CPU3
  505. [    0.022555] Invalid sched_group_energy for CPU3
  506. [    0.022560] CPU3: update cpu_capacity 1024
  507. [    0.022564] CPU3: Booted secondary processor [410fd042]
  508. [    0.022634] Brought up 4 CPUs
  509. [    0.027837] SMP: Total of 4 processors activated.
  510. [    0.028275] CPU: All CPU(s) started at EL2
  511. [    0.028791] Invalid sched_group_energy for CPU3
  512. [    0.029212] Invalid sched_group_energy for Cluster3
  513. [    0.029675] Invalid sched_group_energy for CPU2
  514. [    0.030093] Invalid sched_group_energy for Cluster2
  515. [    0.030542] Invalid sched_group_energy for CPU1
  516. [    0.030970] Invalid sched_group_energy for Cluster1
  517. [    0.031418] Invalid sched_group_energy for CPU0
  518. [    0.031834] Invalid sched_group_energy for Cluster0
  519. [    0.032801] devtmpfs: initialized
  520. [    0.050950] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
  521. [    0.051887] futex hash table entries: 1024 (order: 4, 65536 bytes)
  522. [    0.052847] pinctrl core: initialized pinctrl subsystem
  523. [    0.054429] NET: Registered protocol family 16
  524. [    0.059435] cpuidle: using governor menu
  525. [    0.059830] Registered FIQ tty driver
  526. [    0.060507] vdso: 2 pages (1 code @ ffffff8008626000, 1 data @ ffffff80088a4000)
  527. [    0.061215] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
  528. [    0.062048] DMA: preallocated 256 KiB pool for atomic allocations
  529. [    0.065523] console [pstore-1] enabled
  530. [    0.065874] pstore: Registered ramoops as persistent store backend
  531. [    0.066458] ramoops: attached 0xf0000@0x110000, ecc: 0/0
  532. [    0.084953] fiq debugger fiq mode enabled
  533. [[    0.085703] console [ttyFIQ0] enabled
  534.     0.085703] console [ttyFIQ0] enabled
  535. [    0.086398] bootconsole [uart0] disabled
  536. [    0.086398] bootconsole [uart0] disabled
  537. [    0.087011] Registered fiq debugger ttyFIQ0
  538. WARNING: suspend_mode_handler: Not support call: 0x4
  539. [    0.101795] vcc_1v8: regulator get failed, ret=-517
  540. [    0.102648] vcc_1v8_codec: regulator get failed, ret=-517
  541. [    0.103441] vcc_1v8: supplied by vcc_io
  542. [    0.103532] vcc_1v8_codec: supplied by vcc_io
  543. [    0.105927] SCSI subsystem initialized
  544. [    0.106232] usbcore: registered new interface driver usbfs
  545. [    0.106307] usbcore: registered new interface driver hub
  546. [    0.106438] usbcore: registered new device driver usb
  547. [    0.106581] pps_core: LinuxPPS API ver. 1 registered
  548. [    0.106594] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  549. [    0.106630] PTP clock support registered
  550. [    0.107820] Advanced Linux Sound Architecture Driver Initialized.
  551. [    0.108491] Bluetooth: Core ver 2.21
  552. [    0.108553] NET: Registered protocol family 31
  553. [    0.108565] Bluetooth: HCI device and connection manager initialized
  554. [    0.108585] Bluetooth: HCI socket layer initialized
  555. [    0.108601] Bluetooth: L2CAP socket layer initialized
  556. [    0.108641] Bluetooth: SCO socket layer initialized
  557. [    0.109778] rockchip-cpuinfo cpuinfo: Serial         : a32b06ea995d4011
  558. [    0.110453] clocksource: Switched to clocksource arch_sys_counter
  559. [    0.112907] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
  560. [    0.113242] NET: Registered protocol family 2
  561. [    0.113946] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
  562. [    0.114006] TCP bind hash table entries: 2048 (order: 3, 32768 bytes)
  563. [    0.114062] TCP: Hash tables configured (established 2048 bind 2048)
  564. [    0.114145] UDP hash table entries: 256 (order: 1, 8192 bytes)
  565. [    0.114181] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
  566. [    0.114391] NET: Registered protocol family 1
  567. [    0.114747] Unpacking initramfs...
  568. [    0.558136] Freeing initrd memory: 5896K
  569. [    0.558812] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
  570. [    0.570201] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  571. [    0.570512] ntfs: driver 2.1.32 [Flags: R/W].
  572. [    0.573905] io scheduler noop registered (default)
  573. [    0.575083] phy phy-ff008000.syscon:usb2-phy@100.0: Failed to get VBUS supply regulator
  574. [    0.579317] dma-pl330 ff2c0000.dma-controller: Loaded driver for PL330 DMAC-241330
  575. [    0.579366] dma-pl330 ff2c0000.dma-controller:       DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
  576. [    0.581803] dma-pl330 ff2d0000.dma-controller: Loaded driver for PL330 DMAC-241330
  577. [    0.581843] dma-pl330 ff2d0000.dma-controller:       DBUFF-128x8bytes Num_Cip-pvtm ff000000.grf:pmu-pvtm: failed to get rst 0 pmu
  578. [    0.582349] rockchip-pvtm ff00c000.syscon:pvtm: failed to get rst 0 core
  579. [    0.583854] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled
  580. [    0.586136] ff0e0000.serial: ttyS4 at MMIO 0xff0e0000 (irq = 12, base_baud = 6770833) is a 16550A
  581. [    0.588004] [drm] Initialized drm 1.1.0 20060810
  582. [    0.588171] random: nonblocking pool is initialized
  583. [    0.590946] Unable to detect cache hierarchy for CPU 0
  584. [    0.598053] loop: module loaded
  585. [    0.598413] SCSI Media Changer driver v0.25
  586. [    0.600315] rk_gmac-dwmac ff4e0000.ethernet: clock input or output? (input).
  587. [    0.600360] rk_gmac-dwmac ff4e0000.ethernet: Can not read property: tx_delay.
  588. [    0.600377] rk_gmac-dwmac ff4e0000.ethernet: set tx_delay to 0x30
  589. [    0.600397] rk_gmac-dwmac ff4e0000.ethernet: Can not read property: rx_delay.
  590. [    0.600414] rk_gmac-dwmac ff4e0000.ethernet: set rx_delay to 0x10
  591. [    0.600437] rk_gmac-dwmac ff4e0000.ethernet: integrated PHY? (no).
  592. [    0.600723] rk_gmac-dwmac ff4e0000.ethernet: clock input from PHY
  593. [    0.605758] rk_gmac-dwmac ff4e0000.ethernet: init for RMII
  594. [    0.605895] stmmac - user ID: 0x10, Synopsys ID: 0x35
  595. [    0.605911]  Ring mode enabled
  596. [    0.605922]  DMA HW capability register supported
  597. [    0.605931]  Normal descriptors
  598. [    0.605942]  RX Checksum Offload Engine supported (type 2)
  599. [    0.605952]  TX Checksum insertion supported
  600. [    0.605963]  Wake-Up On Lan supported
  601. [    0.606028]  Enable RX Mitigation via HW Watchdog Timer
  602. [    0.689535] libphy: stmmac: probed
  603. [    0.689577] eth%d: PHY ID 0000ffff at 0 IRQ POLL (stmmac-0:00) active
  604. [    0.689594] eth%d: PHY ID 0000ffff at 1 IRQ POLL (stmmac-0:01)
  605. [    0.689608] eth%d: PHY ID 0000ffff at 2 IRQ POLL (stmmac-0:02)
  606. [    0.689621] eth%d: PHY ID 0000ffff at 3 IRQ POLL (stmmac-0:03)
  607. [    0.689634] eth%d: PHY ID 0000ffff at 4 IRQ POLL (stmmac-0:04)
  608. [    0.689647] eth%d: PHY ID 0000ffff at 5 IRQ POLL (stmmac-0:05)
  609. [    0.689660] eth%d: PHY ID 0000ffff at 6 IRQ POLL (stmmac-0:06)
  610. [    0.689673] eth%d: PHY ID 0000ffff at 7 IRQ POLL (stmmac-0:07)
  611. [    0.689686] eth%d: PHY ID 0000ffff at 8 IRQ POLL (stmmac-0:08)
  612. [    0.689699] eth%d: PHY ID 0000ffff at 9 IRQ POLL (stmmac-0:09)
  613. [    0.689712] eth%d: PHY ID 0000ffff at 10 IRQ POLL (stmmac-0:0a)
  614. [    0.689725] eth%d: PHY ID 0000ffff at 11 IRQ POLL (stmmac-0:0b)
  615. [    0.689739] eth%d: PHY ID 0000ffff at 12 IRQ POLL (stmmac-0:0c)
  616. [    0.689752] eth%d: PHY ID 0000ffff at 13 IRQ POLL (stmmac-0:0d)
  617. [    0.689765] eth%d: PHY ID 0000ffff at 14 IRQ POLL (stmmac-0:0e)
  618. [    0.689778] eth%d: PHY ID 0000ffff at 15 IRQ POLL (stmmac-0:0f)
  619. [    0.689799] eth%d: PHY ID 0000ffff at 16 IRQ POLL (stmmac-0:10)
  620. [    0.689812] eth%d: PHY ID 0000ffff at 17 IRQ POLL (stmmac-0:11)
  621. [    0.689826] eth%d: PHY ID 0000ffff at 18 IRQ POLL (stmmac-0:12)
  622. [    0.689839] eth%d: PHY ID 0000ffff at 19 IRQ POLL (stmmac-0:13)
  623. [    0.689852] eth%d: PHY ID 0000ffff at 20 IRQ POLL (stmmac-0:14)
  624. [    0.689865] eth%d: PHY ID 0000ffff at 21 IRQ POLL (stmmac-0:15)
  625. [    0.689878] eth%d: PHY ID 0000ffff at 22 IRQ POLL (stmmac-0:16)
  626. [    0.689891] eth%d: PHY ID 0000ffff at 23 IRQ POLL (stmmac-0:17)
  627. [    0.689904] eth%d: PHY ID 0000ffff at 24 IRQ POLL (stmmac-0:18)
  628. [    0.689917] eth%d: PHY ID 0000ffff at 25 IRQ POLL (stmmac-0:19)
  629. [    0.689931] eth%d: PHY ID 0000ffff at 26 IRQ POLL (stmmac-0:1a)
  630. [    0.689943] eth%d: PHY ID 0000ffff at 27 IRQ POLL (stmmac-0:1b)
  631. [    0.689957] eth%d: PHY ID 0000ffff at 28 IRQ POLL (stmmac-0:1c)
  632. [    0.689970] eth%d: PHY ID 0000ffff at 29 IRQ POLL (stmmac-0:1d)
  633. [    0.689982] eth%d: PHY ID 0000ffff at 30 IRQ POLL (stmmac-0:1e)
  634. [    0.689996] eth%d: PHY ID 0000ffff at 31 IRQ POLL (stmmac-0:1f)
  635. [    0.691196] Rockchip WiFi SYS interface (V1.00) ...
  636. [    0.691672] ff400000.usb supply vusb_d not found, using dummy regulator
  637. [    0.691801] ff400000.usb supply vusb_a not found, using dummy regulator
  638. [    0.804524] dwc2 ff400000.usb: EPs: 10, dedicated fifos, 972 entries in SPRAM
  639. [    0.805048] dwc2 ff400000.usb: DWC OTG Controller
  640. [    0.805096] dwc2 ff400000.usb: new USB bus registered, assigned bus number 1
  641. [    0.805144] dwc2 ff400000.usb: irq 22, io mem 0xff400000
  642. [    0.806062] hub 1-0:1.0: USB hub found
  643. [    0.806117] hub 1-0:1.0: 1 port detected
  644. [    1.029939] phy phy-ff008000.syscon:usb2-phy@100.0: charger = USB_SDP_CHARGER
  645. [    1.030190] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  646. [    1.030223] ehci-platform: EHCI generic platform driver
  647. [    1.034078] ehci-platform ff440000.usb: EHCI Host Controller
  648. [    1.034130] ehci-platform ff440000.usb: new USB bus registered, assigned bus number 2
  649. [    1.034274] ehci-platform ff440000.usb: irq 23, io mem 0xff440000
  650. [    1.039487] ehci-platform ff440000.usb: USB 2.0 started, EHCI 1.00
  651. [    1.040373] hub 2-0:1.0: USB hub found
  652. [    1.040426] hub 2-0:1.0: 1 port detected
  653. [    1.041053] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  654. [    1.041102] ohci-platform: OHCI generic platform driver
  655. [    1.041529] ohci-platform ff450000.usb: Generic Platform OHCI contq 24, io mem 0xff450000
  656. [    1.097336] hub 3-0:1.0: USB hub found
  657. [    1.097392] hub 3-0:1.0: 1 port detected
  658. [    1.098047] usbcore: registered new interface driver uas
  659. [    1.098201] usbcore: registered new interface driver usb-storage
  660. [    1.098264] usbcore: registered new interface driver ums-alauda
  661. [    1.098324] usbcore: registered new interface driver ums-cypress
  662. [    1.098391] usbcore: registered new interface driver ums-datafab
  663. [    1.098473] usbcore: registered new interface driver ums_eneub6250
  664. [    1.098537] usbcore: registered new interface driver ums-freecom
  665. [    1.098610] usbcore: registered new interface driver ums-isd200
  666. [    1.098670] usbcore: registered new interface driver ums-jumpshot
  667. [    1.098730] usbcore: registered new interface driver ums-karma
  668. [    1.098798] usbcore: registered new interface driver ums-onetouch
  669. [    1.098861] usbcore: registered new interface driver ums-sddr09
  670. [    1.098922] usbcore: registered new interface driver ums-sddr55
  671. [    1.098988] usbcore: registered new interface driver ums-usbat
  672. [    1.099726] i2c /dev entries driver
  673. [    1.100885] rk3x-i2c ff050000.i2c: Initialized RK3xxx I2C bus at ffffff80089be000
  674. [    1.103735] rk_tsadcv2_temp_to_code: Invalid conversion table: code=4095, temperature=2147483647
  675. [    1.103965] rockchip-thermal ff1f0000.tsadc: tsadc is probed successfully!
  676. [    1.104600] Bluetooth: HCI UART driver ver 2.3
  677. [    1.104626] Bluetooth: HCI UART protocol H4 registered
  678. [    1.104637] Bluetooth: HCI UART protocol LL registered
  679. [    1.104874] cpu cpu0: leakage=13
  680. [    1.105103] cpu cpu0: Failed to get pvtm
  681. [    1.107674] Synopsys Designware Multimedia Card Interface Driver
  682. [    1.109383] dwmmc_rockchip ff480000.dwmmc: num-slots property not found, assuming 1 slot is available
  683. [    1.109564] dwmmc_rockchip ff480000.dwmmc: IDMAC supports 32-bit address mode.
  684. [    1.109609] dwmmc_rockchip ff480000.dwmmc: Using internal DMA controller.
  685. [    1.109639] dwmmc_rockchip ff480000.dwmmc: Version ID is 270a
  686. [    1.109716] dwmmc_rockchip ff480000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo
  687. [    1.110549] rockchip-iodomain ff000000.grf:io-domains: Setting to 3300000 done
  688. [    1.110589] rockchip-iodomain ff000000.grf:io-domains: Setting to 3300000 done
  689. [    1.121553] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
  690. [    1.132626] rockchip-iodomain ff000000.grf:io-domains: Setting to 3300000 done
  691. [    1.132659] rockchip-iodomain ff000000.grf:io-domains: Setting to 3300000 done
  692. [    1.132674] set vqmmc to 3.3v, ret=0
  693. [    1.133187] dwmmc_rockchip ff480000.dwmmc: 1 slots initialized
  694. [    1.133425] dwmmc_rockchip ff490000.dwmmc: No default pinctrl state
  695. [    1.133484] dwmmc_rockchip ff490000.dwmmc: No off pinctrl state
  696. [    1.133613] dwmmc_rockchip ff490000.dwmmc: IDMAC supports 32-bit address mode.
  697. [    1.133662] dwmmc_rockchip ff490000.dwmmc: Using internal DMA controller.
  698. [    1.133684] dwmmc_rockchip ff490000.dwmmc: Version ID is 270a
  699. [    1.133763] dwmmc_rockchip ff490000.dwmmc: DW MMC controller at irq 26,32 bit host data width,256 deep fifo
  700. [    1.133842] dwmmc_rockchip ff490000.dwmmc: No vmmc regulator found
  701. [    1.133859] dwmmc_rockchip ff490000.dwmmc: No vqmmc regulator found
  702. [    1.144628] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
  703. [    1.155613] dwmmc_rockchip ff490000.dwmmc: 1 slots initialized
  704. [    1.156189] dwmmc_rockchip ff4a0000.dwmmc: No default pinctrl state
  705. [    1.156213] dwmmc_rockchip ff4a0000.dwmmc: No off pinctrl state
  706. [    1.156229] dwmmc_rockchip ff4a0000.dwmmc: num-slots property not found, assuming 1 slot is available
  707. [    1.156325] dwmmc_rockchip ff4a0000.dwmmc: IDMAC supports 32-bit address mode.
  708. [    1.156371] dwmmc_rockchip ff4a0000.dwmmc: Using internal DMA controller.
  709. [    14a0000.dwmmc: DW MMC controller at irq 27,32 bit host data width,256 deep fifo
  710. [    1.156552] dwmmc_rockchip ff4a0000.dwmmc: No vmmc regulator found
  711. [    1.156570] dwmmc_rockchip ff4a0000.dwmmc: No vqmmc regulator found
  712. [    1.156878] dwmmc_rockchip ff4a0000.dwmmc: allocated mmc-pwrseq
  713. [    1.167589] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
  714. [    1.178617] dwmmc_rockchip ff4a0000.dwmmc: 1 slots initialized
  715. [    1.180007] is31fl32xx 1-003c: register write to 0x00 failed (error -6),val=0
  716. [    1.191360] mmc1: MAN_BKOPS_EN bit is not set
  717. [    1.194793] mmc_host mmc1: Bus speed (slot 0) = 147456000Hz (slot req 150000000Hz, actual 147456000HZ div = 0)
  718. [    1.203568] mmc_host mmc2: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
  719. [    1.240545] mmc_host mmc2: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0)
  720. [    1.280620] is31fl32xx 1-003c: register write to 0x00 failed (error -6),val=0
  721. [    1.281527] mmc_host mmc2: Bus speed (slot 0) = 100000Hz (slot req 100000Hz, actual 100000HZ div = 0)
  722. [    1.381616] is31fl32xx 1-003c: register write to 0x00 failed (error -6),val=0
  723. [    1.482611] is31fl32xx_init_regs, write to shutdown register failed
  724. [    1.482735] is31fl32xx 1-003c: register write to 0x26 failed (error -6),val=1
  725. [    1.571286] dwmmc_rockchip ff490000.dwmmc: Successfully tuned phase to 60
  726. [    1.571443] mmc1: new HS200 MMC card at address 0001
  727. [    1.572991] mmcblk1: mmc1:0001 8GTF4R 7.28 GiB
  728. [    1.574856] mmcblk1boot0: mmc1:0001 8GTF4R partition 1 4.00 MiB
  729. [    1.576776] mmcblk1boot1: mmc1:0001 8GTF4R partition 2 4.00 MiB
  730. [    1.577781] mmcblk1rpmb: mmc1:0001 8GTF4R partition 3 512 KiB
  731. [    1.583644] is31fl32xx 1-003c: register write to 0x26 failed (error -6),val=1
  732. [    1.583826]  mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8
  733. [    1.684743] is31fl32xx 1-003c: register write to 0x26 failed (error -6),val=1
  734. [    1.786182] usbcore: registered new interface driver usbhid
  735. [    1.786228] usbhid: USB HID core driver
  736. [    1.786515] rockchip-dmc dmc: failed to get the count of devfreq-event in /dmc node
  737. [    1.786943] rockchip-dmc dmc: Failed to get leakage
  738. [    1.787100] rockchip-dmc dmc: Failed to get pvtm
  739. [    1.787695] rockchip-dmc dmc: failed to get vop bandwidth to dmc rate
  740. [    [    1.791487] rknandc_base v1.1 2017-01-11
  741. [    1.791948] rksfc_base v1.1 2016-01-08
  742. [    1.800413] rk3308-acodec ff560000.acodec: Don't need pa-drv gpio
  743. [    1.800516] rk3308-acodec ff560000.acodec: De-pop as much as possible
  744. [    1.801729] 1-001a supply AVDD not found, using dummy regulator
  745. [    1.801878] 1-001a supply DVDD not found, using dummy regulator
  746. [    1.801988] 1-001a supply PVDD_A not found, using dummy regulator
  747. [    1.802091] 1-001a supply PVDD_B not found, using dummy regulator
  748. [    1.802202] 1-001a supply PVDD_C not found, using dummy regulator
  749. [    1.802316] 1-001a supply PVDD_D not found, using dting pdn_gpio: -16
  750. [    1.80334[    1.808898] rk-multicodecs bluetooth-sound: card: 0 has not been locked, re-probe again
  751. [    1.808943] rk-multicodecs bluetooth-sound: check_lock_card failed: -517
  752. [    1.809194] rk-multicodecs vad-sound: ASoC: CPU DAI (null) not registered
  753. [    1.810136] NET: Registered protocol family 10
  754. [    1.811386] NET: Registered protocol family 17
  755. [    1.811492] NET: Registered protocol family 15
  756. [    1.811766] Bluetooth: RFCOMM TTY layer initialized
  757. [    1.811793] Bluetooth: RFCOMM socket layer initialized
  758. [    1.811827] Bluetooth: RFCOMM ver 1.11
  759. [    1.811851] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  760. [    1.811867] Bluetooth: HIDP socket layer initialized
  761. [    1.811882] [WLAN_RFKILL]: Enter rfkill_wlan_init
  762. [    1.812391] [WLAN_RFKILL]: Enter rfkill_wlan_probe
  763. [    1.812423] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6236
  764. [    1.812433] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
  765. [    1.812477] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
  766. [    1.812564] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 0, flags = 1.
  767. [    1.812580] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
  768. [    1.812589] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
  769. [    1.812610] [WLAN_RFKILL]: Exit rfkill_wlan_probe
  770. [    1.812689] [BT_RFKILL]: Enter rfkill_rk_init
  771. [    1.813134] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 135.
  772. [    1.813175] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,power_gpio = 139.
  773. [    1.813226] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 140.
  774. [    1.813238] [BT_RFKILL]: bluetooth_platdata_parse_dt: clk_get failed!!!.
  775. [    1.813305] [BT_RFKILL]: Request irq for bt wakeup host
  776. [    1.813371] [BT_RFKILL]: ** disable irq
  777. [    1.813568] [BT_RFKILL]: bt_default device registered.
  778. [    1.814110] flash vendor_init_thread!
  779. [    1.814151] flash vendor storage:20170308 ret = -1
  780. [    1.814813] vendor storage:20160801 ret = 0
  781. [    1.816134] input: adc-keys as /devices/platform/adc-keys/input/input0
  782. [    1.817331] rk-multicodecs bluetooth-sound: card: 0 has not been locked, re-probe again
  783. [    1.817356] rk-multicodecs bluetooth-sound: check_lock_card failed: -517
  784. [    1.890144] rk-multicodecs vad-sound: multicodec <-> pdm-i2s-dais mapping ok
  785. [    1.896249] rk-multicodecs bluetooth-sound: dummy_codec <-> ff350000.i2s mapping ok
  786. [    1.899553] dhd_module_init: in Dongle Host Driver, version 1.579.77.41.2 (r)
  787. [    1.899614] ======== dhd_wlan_init_plat_data ========
  788. [    1.899637] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
  789. [    1.899658] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
  790. [    1.899679] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter
  791. [    1.899704] dhd_wlan_init_gpio: host_oob_irq: 36
  792. [    1.899742] dhd_wlan_init_gpio: host_oob_irq_flags=0x418
  793. [    1.899761] dhd_wifi_platform_load: Enter
  794. [    1.899855] Power-up adapter 'DHD generic adapter'
  795. [    1.899965] wifi_platform_set_power = 1
  796. [    1.899986] hctosys: unable to open rtc device (rtc0)
  797. [    1.900012] ======== PULL WL_REG_ON(-1) HIGH! ========
  798. [    1.900034] [WLAN_RFKILL]: rockchip_wifi_power: 1
  799. [    1.900055] [WLAN_RFKILL]: wifi turn on power. -1
  800. [    1.925158] vcc_sd: disabling
  801. [    1.925243] vccio_sd: disabling
  802. u▒   1.925960]
复制代码
作者: zhangdexingzdx    时间: 2020-7-27 16:41
用自己的源码编译的镜像试试，  把wifi的配置先取消掉
作者: keithc    时间: 2020-8-7 17:18
kernel/arch/arm64/configs/firefly-rk3308_linux_defconfig 檔內原本的CONFIG_WL_ROCKCHIP , CONFIG_WIFI_LOAD_DRIVER_WHEN_KERNEL_BOOTUP, CONFIG_AP6XXX 都已加 # 了

# CONFIG_WL_ROCKCHIP=y
# CONFIG_WIFI_LOAD_DRIVER_WHEN_KERNEL_BOOTUP=y
# CONFIG_AP6XXX=
作者: keithc    时间: 2020-8-20 13:27
试过很多次 有时能 boot 有时不能 能boot 机的时候一定有 "ret 1024" 这个东西出现在 kernel,   不能 boot的时候便卡在 出 "ret 1024" 之前, 24 秒後 kernel 自动 reboot  ....

成功时:

  1. [    1.230567] input: adc-keys1 as /devices/platform/adc-keys1/input/input1
  2. [    1.231571] rk-multicodecs bluetooth-sound: card: 0 has not been locked, re-probe again
  3. [    1.231603] rk-multicodecs bluetooth-sound: check_lock_card failed: -517
  4. [    1.285904] rk-multicodecs vad-sound: multicodec <-> pdm-i2s-dais mapping ok
  5. [    1.289352] rk-multicodecs bluetooth-sound: dummy_codec <-> ff350000.i2s mapping ok
  6. [    1.291563] input: gpio-keys as /devices/platform/gpio-keys/input/input2
  7. [    2.305438] ret 1024
  8. [    2.306514] ALSA device list:
  9. [    2.306540]   #0: rockchip,rk3308-vad
  10. [    2.306572]   #1: rockchip,rk3308-pcm
  11. [    2.306591]   #7: Loopback 1
  12. [    2.310356] VFS: Mounted root (squashfs filesystem) readonly on device 179:6.
  13. [    2.312626] devtmpfs: mounted
  14. [    2.313009] Freeing unused kernel memory: 320K
复制代码


在 System.map 可看到

  1. ffffff80086db4a0 t __initcall_regulator_init_complete7s
  2. ffffff80086db4a8 t __initcall_drm_misc_init7s                          <---------------------
  3. ffffff80086db4b0 t __initcall_rockchip_clocks_loader_unprotect7s
  4. ffffff80086db4b8 t __initcall_clk_disable_unused7s
  5. ffffff80086db4c0 t __initcall_alsa_sound_last_init7s

复制代码


drm_misc_init 是跑在 regulator_init_complete 之後， rockchip_clocks_loader_unprotect 之前。 我在代码加了 "---->" 在 regulator_init_complete  rockchip_clocks_loader_unprotect  这2 个函数内， 证明了 "ret 1024" 是 drm_misc_init 内印出来。

  1.     1.230567] input: adc-keys1 as /devices/platform/adc-keys1/input/input1
  2. [    1.231571] rk-multicodecs bluetooth-sound: card: 0 has not been locked, re-probe again
  3. [    1.231603] rk-multicodecs bluetooth-sound: check_lock_card failed: -517
  4. [    1.285904] rk-multicodecs vad-sound: multicodec <-> pdm-i2s-dais mapping ok
  5. [    1.289352] rk-multicodecs bluetooth-sound: dummy_codec <-> ff350000.i2s mapping ok
  6. [    1.291563] input: gpio-keys as /devices/platform/gpio-keys/input/input2
  7. [    1.304214] ----->regulator_init_complete start 我加的
  8. [    1.304348] ----->regulator_init_complete stop 我加的
  9. [    2.305438] ret 1024
  10. [    2.305890] ----->start rockchip_clocks_loader_unprotect   我加的
  11. [    2.305933] ----->stop rockchip_clocks_loader_unprotect  我加的
  12. [    2.306514] ALSA device list:
  13. [    2.306540]   #0: rockchip,rk3308-vad
  14. [    2.306572]   #1: rockchip,rk3308-pcm
  15. [    2.306591]   #7: Loopback 1
  16. [    2.310356] VFS: Mounted root (squashfs filesystem) readonly on device 179:6.
  17. [    2.312626] devtmpfs: mounted
  18. [    2.313009] Freeing unused kernel memory: 320K
复制代码


但我找不到 drm_misc_init 这个函数！     

我亦试过在 kernel 不包含 DRM 这项，可是 kernel 便不能编译 !!!!


1. 那里可找到 drm_misc_init  这个函数 ?
2. DRM 可否 disable 而把 kernel 编译到？

作者: firebug    时间: 2020-8-23 21:26
你好 问题解决了吗 我也是一样的问题



欢迎光临 Firefly开源社区 (https://dev.t-firefly.com/) Powered by Discuz! X3.1