正常的log:
[ 0.638220] flash vendor_init_thread!
[ 0.638253] flash vendor storage:20170308 ret = -1
[ 0.640713] input: adc-keys as /devices/platform/adc-keys/input/input1
[ 0.642640] rk808-rtc rk808-rtc: setting system clock to 2015-01-20 08:50:01 UTC (1421743801)
[ 0.660873] mmc0: MAN_BKOPS_EN bit is not set
[ 0.662277] mmc_host mmc0: Bus speed (slot 0) = 50176000Hz (slot req 52000000Hz, actual 50176000HZ div = 0)
[ 0.663935] mmc0: new high speed MMC card at address 0001
[ 0.664806] mmcblk0: mmc0:0001 Q2J54A 3.59 GiB
[ 0.665305] mmcblk0boot0: mmc0:0001 Q2J54A partition 1 16.0 MiB
[ 0.665762] mmcblk0boot1: mmc0:0001 Q2J54A partition 2 16.0 MiB
[ 0.666187] mmcblk0rpmb: mmc0:0001 Q2J54A partition 3 512 KiB
[ 0.671947] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8
[ 1.141137] vendor storage:20160801 ret = 0 [ 2.658972] ret 1024 //这是什么模块的log???
[ 2.667972] VFS: Mounted root (squashfs filesystem) readonly on device 179:6.
[ 2.671373] devtmpfs: mounted
[ 2.671747] Freeing unused kernel memory: 320K
mount: /misc: mount point does not exist.
mount: /oem: special device /dev/block/by-name/oem does not exist.
mount: /userdata: special device /dev/block/by-name/userdata does not exist.
Starting logging: OK
Set system time from hardware clock
Populating /dev using udev: [ 3.557317] udevd[146]: starting version 3.2.5
[ 3.595244] udevd[147]: starting eudev-3.2.5
done
read-only file system detected...done
Will now mount all partitions in /etc/fstab
Note: Create /.skip_fsck to skip fsck - The check might take a while if didn't shutdown properly!
Handling /dev/mmcblk0p6 / ext2 rw,noauto 1
Wrong fs type(ext2) for /dev/mmcblk0p6
Handling /dev/mmcblk0p3 /misc emmc defaults 0
Unsupported file system emmc for /dev/mmcblk0p3
Handling /dev/mmcblk0p7 /oem ext2 defaults 2
Checking /dev/mmcblk0p7(ext2)
e2fsck 1.43.9 (8-Feb-2018)
oem was not cleanly unmounted, check forced.
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
oem: 23/3696 files (4.3% non-contiguous), 18821/131072 blocks
Mounting /dev/mmcblk0p7(ext2) on /oem
Handling /dev/mmcblk0p8 /userdata ext2 defaults 2
Checking /dev/mmcblk0p8(ext2)
e2fsck 1.43.9 (8-Feb-2018)
Superblock last write time is in the future.
(by less than a day, probably due to the hardware clock being incorrectly set)
userdata was not cleanly unmounted, check forced.
Pass 1: Checking inodes, blocks, and sizes
[ 5.595352] rk816-bat: changed: dsoc=22, rsoc=22, v=4622, ov=3726 c=1, cap=613, f=2750, st=cc cv, hotdie=0
[ 5.595431] rk816-bat: dl=22, rl=0, v=3274, halt=0, halt_n=0, max=0, init=0, sw=0, calib=0, below0=0, force=0
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
userdata: 17/212992 files (0.0% non-contiguous), 14838/850427 blocks
Mounting /dev/mmcblk0p8(ext2) on /userdata
Log saved to /tmp/mountall.log
Starting system message bus: done
Starting network: ip: RTNETLINK answers: File exists
FAIL
Starting dhcpcd...
no valid interfaces found
no interfaces have a carrier
forked to background, child pid 482
Starting watch_ntpd.sh: OK
Starting pulseaudio: run ntpd once and watch it every 86400 seconds
20 Jan 16:50:08 ntpd[492]: ntpd 4.2.8p10@1.3728-o Sun Dec 6 07:08:57 UTC 2020 (1): Starting
20 Jan 16:50:08 ntpd[492]: Command line: ntpd -gq
W: [pulseaudio] main.c: Running in system mode, but --disallow-exit not set.
W: [pulseaudio] main.c: Running in system mode, but --disallow-module-loading not set.
N: [pulseaudio] main.c: Running in system mode, forcibly disabling SHM mode.
20 Jan 16:50:08 ntpd[492]: proto: precision = 0.583 usec (-21)
E: [pulseaudio] main.c: Daemon startup failed.
20 Jan 16:50:08 ntpd[492]: Listen and drop on 0 v6wildcard [::]:123
20 Jan 16:50:08 ntpd[492]: Listen and drop on 1 v4wildcard 0.0.0.0:123
OK
20 Jan 16:50:08 ntpd[492]: Listen normally on 2 lo 127.0.0.1:123
20 Jan 16:50:08 ntpd[492]: Listen normally on 3 lo [::1]:123
20 Jan 16:50:08 ntpd[492]: Listening on routing socket on fd #20 for interface updates
[ 7.292893] file system registered
install_listener('tcp:5037','*smartsocket*')
[ 7.340049] read descriptors
[ 7.340102] read strings
[ 8.333909] dwc2 ff400000.usb: bound driver configfs-gadget
load wifi modules: /etc/init.d/S66load_wifi_modules: line 42: rk_wifi_init: not found
FAIL
wl: wl driver adapter not found
Starting dnsmasq: OK
[ 8.492896] dwc2 ff400000.usb: new device is high-speed
[ 8.525765] dwc2 ff400000.usb: new address 47
[ 8.545931] android_work: sent uevent USB_STATE=CONNECTED
WAKE_LOCK[open_file_descriptors] fatal error opening "/sys/power/wake_lock": No such file or directory
==========EQ/DRC process release version 1.23===============
ALSA lib pcm_hw.c:1806:(_snd_pcm_hw_open) Invalid value for card
Unable to open capture PCM device:
[ 8.670791] configfs-gadget gadget: high-speed config #1: b [ 8.671003] android_work: sent uevent USB_STATE=CONFIGURED //ADB work
ALSA lib pcm_direct.c:1832:(_snd_pcm_direct_get_slave_ipc_offset) Invalid value for card
aplay: main:828: audio open error: No such file or directory
Successfully initialized wpa_supplicant
Could not read interface wlan0 flags: No such device
nl80211: Driver does not support authentication/association or connect commands
nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Could not read interface wlan0 flags: No such device
wlan0: Failed to initialize driver interface
amixer: Control default open error: No such file or directory
amixer: Control default open error: No such file or directory
amixer: Control default open error: No such file or directory
amixer: Control default open error: No such file or directory
/etc/init.d/S98_lunch_init: source: line 7: can't open '/data/cfg/rockchip_test/auto_reboot.sh'
Starting input-event-daemon: input-event-daemon: open(/dev/input/event2): No such file or directory