Firefly开源社区

标题: PX30 linux 256MB DDR3 UBOOT启动不了 [打印本页]
作者: jukeboge    时间: 2021-6-10 17:30
标题: PX30 linux 256MB DDR3 UBOOT启动不了
硬件平台：firefly px30
SDK: firefly px30 linux sdk
问题描述：更换板子DDR容量为256MB 发现uboot启动不了，未更换前可以正常启动，log如下：
  1. @▒▒L▒▒▒▒▒▒DDR V1.15 20200511
  2. D3,256MB,333MHz
  3. bw      col     bk      row     cs      dbw
  4. 32      10      8       13      1       16
  5. OUT
  6. Boot1 Release Time: Nov 20 2019 15:02:03, version: 1.22
  7. chip_id:50583330_0,0
  8. SdmmcInit=0 NOT PRESENT
  9. ...2578 @ nand_flash_init
  10. ...nandc_init enter... 00000000ff3b0000
  11. 0:80f00 2081 101003 27 200
  12. g_nandc_ver...9
  13. mmc Ext_csd, ret=0 ,
  14. Ext[226]=20, bootSize=2000,
  15.                         Ext[215]=0, Ext[214]=74, Ext[213]=80, Ext[212]=0,cap =748000 REL=1f
  16. mmc2:cmd19,100
  17. emmc bus: 0x8
  18. SdmmcInit=2 0
  19. BootCapSize=2000
  20. UserCapSize=3728MB
  21. FwPartOffset=2000 , 2000
  22. UsbBoot ...94285
  23. powerOn 747066
  24. SoftReset, 24184046 us

  26. DDR V1.15 20200511
  27. SRX
  28. D3,256MB,333MHz
  29. bw      col     bk      row     cs      dbw
  30. 32      10      8       13      1       16
  31. OUT
  32. Boot1 Release Time: Nov 20 2019 14:41:00, version: 1.22
  33. chip_id:50583330_0,0
  34. ChipType = 0x12, 458
  35. mmc2:cmd19,100
  36. SdmmcInit=2 0
  37. BootCapSize=2000
  38. UserCapSize=3728MB
  39. FwPartOffset=2000 , 2000
  40. SdmmcInit=0 NOT PRESENT
  41. StorageInit ok = 9215
  42. SecureMode = 0
  43. Secure read PBA: 0x4
  44. Secure read PBA: 0x404
  45. Secure read PBA: 0x804
  46. Secure read PBA: 0xc04
  47. Secure read PBA: 0x1004
  48. SecureInit ret = 0, SecureMode = 0
  49. atags_set_bootdev: ret:(0)
  50. GPT part:  0, name:            uboot, start:0x4000, size:0x2000
  51. GPT part:  1, name:            trust, start:0x6000, size:0x2000
  52. GPT part:  2, name:             misc, start:0x8000, size:0x2000
  53. GPT part:  3, name:             boot, start:0xa000, size:0x10000
  54. GPT part:  4, name:         recovery, start:0x1a000, size:0x10000
  55. GPT part:  5, name:             fpga, start:0x3a000, size:0x10000
  56. GPT part:  6, name:           rootfs, start:0x5a000, size:0x200000
  57. GPT part:  7, name:         userdata, start:0x25a000, size:0x4edfdf
  58. find part:uboot OK. first_lba:0x4000.
  59. find part:trust OK. first_lba:0x6000.
  60. LoadTrust Addr:0x6000
  61. No find bl30.bin
  62. Load uboot, ReadLba = 4000
  63. Load OK, addr=0x200000, size=0xd6430
  64. RunBL31 0x40000 @ 71251 us
  65. INFO:    Preloader serial: 2
  66. NOTICE:  BL31: v1.3(debug):857e9c1b4
  67. NOTICE:  BL31: Built : 11:50:33, Aug 21 2020
  68. NOTICE:  BL31:Rockchip release version: v1.0
  69. INFO:    ARM GICv2 driver initialized
  70. INFO:    Using opteed sec cpu_context!
  71. INFO:    boot cpu mask: 1
  72. INFO:    plat_rockchip_pmu_init: pd status f00e
  73. INFO:    BL31: Initializing runtime services
  74. INFO:    BL31: Initializing BL32
  75. I/TC:
  76. I/TC: Start rockchip platform init
  77. I/TC: Rockchip release version: 1.1
  78. I/TC: OP-TEE version: 3.6.0-284-g82765277 #12 Thu Sep 17 03:47:31 UTC 2020 aarch64
  79. I/TC: Initialized
  80. INFO:    BL31: Preparing for EL3 exit to normal world
  81. INFO:    Entry point address = 0x200000
  82. INFO:    SPSR = 0x3c9


  85. U-Boot 2017.09 (May 29 2021 - 17:36:04 +0800)

  87. Model: Rockchip PX30 EVB
  88. PreSerial: 2
  89. DRAM:  224 MiB
  90. Sysmem: init
  91. ERROR: Failed to allocate 0xe226980 bytes below 0x10000000.
  92. Sysmem Error: Failed to alloc "U-Boot" at 0x01dd9680 - 0x10000000

  94. sysmem_dump_all:
  95.     --------------------------------------------------------------------
  96.     memory.rgn[0].addr     = 0x00200000 - 0x08400000 (size: 0x08200000)
  97.     memory.rgn[1].addr     = 0x0a200000 - 0x10000000 (size: 0x05e00000)

  99.     memory.total           = 0x0e000000 (224 MiB. 0 KiB)
  100.     --------------------------------------------------------------------


  103.     framework malloc_r     = 192 MiB
  104.     framework malloc_f     =   8 KiB

  106.     allocated.total        = 0x00000000 (0 MiB. 0 KiB)
  107.     --------------------------------------------------------------------
  108.     LMB.allocated[0].addr  = 0x00000000 - 0x00000000 (size: 0x00000000)

  110.     reserved.core.total    = 0x00000000 (0 MiB. 0 KiB)
  111.     --------------------------------------------------------------------

  113. Sysmem Error: Failed to reserve sysmem for U-Boot framework

  115. sysmem_dump_all:
  116.     --------------------------------------------------------------------
  117.     memory.rgn[0].addr     = 0x00200000 - 0x08400000 (size: 0x08200000)
  118.     memory.rgn[1].addr     = 0x0a200000 - 0x10000000 (size: 0x05e00000)

  120.     memory.total           = 0x0e000000 (224 MiB. 0 KiB)
  121.     --------------------------------------------------------------------


  124.     framework malloc_r     = 192 MiB
  125.     framework malloc_f     =   8 KiB

  127.     allocated.total        = 0x00000000 (0 MiB. 0 KiB)
  128.     --------------------------------------------------------------------
  129.     LMB.allocated[0].addr  = 0x00000000 - 0x00000000 (size: 0x00000000)

  131.     reserved.core.total    = 0x00000000 (0 MiB. 0 KiB)
  132.     --------------------------------------------------------------------

  134. Sysmem Warn: Maybe malloc size 192 MiB is too large?

  136. initcall sequence 00000000002922a8 failed at call 00000000002788b4 (err=-12)
  137. ### ERROR ### Please RESET the board ###

复制代码








欢迎光临 Firefly开源社区 (https://dev.t-firefly.com/) Powered by Discuz! X3.1