Firefly开源社区

标题: rk3288-reload在ubuntu/linux下适配DVP接口摄像头驱动问题 [打印本页]

作者: CallMeBroYang 时间: 2016-8-11 17:44
标题: rk3288-reload在ubuntu/linux下适配DVP接口摄像头驱动问题
本帖最后由 CallMeBroYang 于 2016-8-11 19:50 编辑

问题：
接上官方的DVP接口的s5k4ecgx摄像头，上电开机，/dev/下找不到video设备。

这里要发下牢骚：官方什么时候可以出ubuntu/linux下直接支持rk3288 dvp接口摄像头的内核，也省得每个人都花时间做适配。

用的ubuntu镜像版本：FireFly-RK3288-Reload_Ubuntu14.04_201603111814

已进行操作如下：
1、
从https://bitbucket.org/T-Firefly/firenow-lollipop/commits/branch/Firefly-RK3288上下载 android5.1 sdk 最新的内核
git pull bitbucket Firefly-RK3288:Firefly-RK3288
make firefly-rk3288-reload-linux_defconfig

make menuconfig；加上cif选项

2、
从fireprime的内核中，把 ./drivers/media/video/s5k4ec.c，复制过来并修改修改Makefile
参照fireprime的内核，修改./include/media/v4l2-chip-ident.h，添加相关宏
参照fireprime的内核，修改./arch/arm/mach-rockchip/rk_camera.c
在./arch/arm/boot/dts下修改rk3288-cif-sensor.dts，添加
14    s5k4ec{
15             status = "okay";
16             is_front = <0>;
17             //rockchip,power_pmu_name1 = "rk818_ldo4";/*cif 2.8v */
18             //rockchip,power_pmu_voltage1 = <2800000>;
19             //rockchip,power_pmu_name2 = "rk818_ldo8";/* cif 1.8v */
20             //rockchip,power_pmu_voltage2 = <1800000>;
21             rockchip,powerdown = <&gpio3 GPIO_B4 GPIO_ACTIVE_HIGH>;
22             pwdn_active = <0>;
23             tchip,rst = <&gpio2 GPIO_B7 GPIO_ACTIVE_LOW>;
24             //rockchip,power = <&gpio3 GPIO_D7 GPIO_ACTIVE_HIGH>;
25             //pwr_active = <PWR_ACTIVE_HIGH>;
26             #rockchip,reset = <>;
27             #rst_active = <>;
28             flash_attach = <1>;
29             rockchip,flash = <&gpio2 GPIO_C6 GPIO_ACTIVE_HIGH>;   //不知道怎么修改
30             flash_active = <GPIO_ACTIVE_LOW>;
31             #rockchip,af = <>;
32             mir = <0>;
33             resolution = <0x500000>;
34             powerup_sequence = <s5k4ec_PWRSEQ_DEFAULT>;
35             orientation = <0>;
36             i2c_add = <s5k4ec_I2C_ADDR>;
37             i2c_rata = <20000>;
38             i2c_chl = <3>;
39             cif_chl = <0>;
40             mclk_rate = <24>;
41    };

修改 arch/arm/boot/dts/firefly-rk3288-reload-linux.dts@@ -1,6 +1,7 @@
/dts-v1/;

#include "rk3288.dtsi"
+#include "rk3288-cif-sensor.dtsi"
#include "lcd-box.dtsi"
#include <dt-bindings/input/input.h>

@@ -191,6 +192,10 @@
   };
};

+&rk3288_cif_sensor {
+       status = "okay";
+};
+

3、
make -j8 firefly-rk3288-reload-linux.img
从官方镜像的linux-boot.img提取initrd.img，并与新编译的kernel压缩
mkbootimg --kernel arch/arm/boot/zImage --ramdisk initrd.img -o kernel-boot.img

4、
kernel-boot.img下载到boot分区，resource.img下载到resource分区，
开机后进入系统，还是找不到video设备

内核打印信息：
[ 1.834056] Key type dns_resolver registered
[ 1.834179] rk_cam_cif(3053):rk312x-camera version: v0.2.0  Zoom by ipp
[ 1.834455] rockchip-pinctrl ff770000.pinctrl: pin gpio2-11 already requested by ff910000.isp; cannot claim for ff950000.cif
[ 1.834477] rockchip-pinctrl ff770000.pinctrl: pin-75 (ff950000.cif) status -22
[ 1.834490] rockchip-pinctrl ff770000.pinctrl: could not request pin 75 on device rockchip-pinctrl
[ 1.834504] rk_cif ff950000.cif: Error applying setting, reverse things back
[ 1.834517] rk_cif ff950000.cif: rk_camera_cif_iomux:could not set cif_pin_all pins
[ 1.834700] soc-camera-pdrv s5k4ec_back_3: Probing s5k4ec_back_3
。
。
。
[ 2.381463] udevd[150]: starting version 175
[ 2.423244] rockchip_i2c ff150000.i2c: i2c is not in idle(state = 3)
[ 2.423273] s5k4ec_back_3(rk_cam_sensor:167): write reg(0xfcfc, val:0xd000) failed, try to write again!
[ 2.462595] [WLAN_RFKILL]: wifi turn on power. 156
[ 2.620004] rockchip_i2c ff150000.i2c: i2c is not in idle(state = 3)
[ 2.620027] s5k4ec_back_3(rk_cam_sensor:167): write reg(0xfcfc, val:0xd000) failed, try to write again!
[ 2.620052] s5k4ec_back_3(rk_cam_sensor:385): write array failed!
[ 2.620061] s5k4ec_back_3(rk_cam_sensor:669): soft reset failed
[ 2.620061]
[ 2.669237] mmc2:mmc host rescan start!
[ 2.728207] EXT4-fs (mmcblk0p5): 2 orphan inodes deleted
[ 2.728221] EXT4-fs (mmcblk0p5): recovery complete
[ 2.731094] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null)
[ 2.836494] rockchip_i2c ff150000.i2c: i2c is not in idle(state = 3)
[ 2.836519] s5k4ec_back_3(rk_cam_sensor:167): write reg(0x2c, val:0x7000) failed, try to write again!
[ 2.920336] mmc2: queuing unknown CIS tuple 0x80 (2 bytes)
[ 2.921848] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
[ 2.923356] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
[ 2.926072] mmc2: queuing unknown CIS tuple 0x80 (7 bytes)
[ 2.978600] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[ 2.980815] mmc2: queuing unknown CIS tuple 0x91 (3 bytes)
[ 2.980840] mmc2: new high speed SDIO card at address 0001
[ 2.999732] [WLAN_RFKILL]: rockchip_wifi_mac_addr: enter.
[ 2.999744] [WLAN_RFKILL]: falsh wifi_custom_mac_addr=[00:00:00:00:00:00]
[ 2.999754] [WLAN_RFKILL]: This mac address is not valid, ignored...
[ 3.005830] [WLAN_RFKILL]: rockchip_wifi_power: 0
[ 3.033284] rockchip_i2c ff150000.i2c: i2c is not in idle(state = 3)
[ 3.033301] s5k4ec_back_3(rk_cam_sensor:167): write reg(0x2c, val:0x7000) failed, try to write again!
[ 3.083851] EHCI: rk_ehci_hcd_enable, disable host controller
[ 3.112000] [WLAN_RFKILL]: wifi shut off power.
[ 3.112011] [WLAN_RFKILL]: rockchip_wifi_ref_voltage: 0
[ 3.112021] [WLAN_RFKILL]: rockchip_wifi_ref_voltage: wifi io reference voltage control is disabled.
[ 3.230086] rockchip_i2c ff150000.i2c: i2c is not in idle(state = 3)
[ 3.230102] s5k4ec_back_3(rk_cam_sensor:167): write reg(0x2c, val:0x7000) failed, try to write again!
[ 3.426883] rockchip_i2c ff150000.i2c: i2c is not in idle(state = 3)
[ 3.426898] s5k4ec_back_3(rk_cam_sensor:167): write reg(0x2e, val:0x1a4) failed, try to write again!
[ 3.446577] usb 3-1: new high-speed USB device number 2 using usb20_host
[ 3.623685] rockchip_i2c ff150000.i2c: i2c is not in idle(state = 3)
[ 3.623699] s5k4ec_back_3(rk_cam_sensor:167): write reg(0x2e, val:0x1a4) failed, try to write again!
[ 3.643567] usb 3-1: New USB device found, idVendor=1a40, idProduct=0101
[ 3.643583] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 3.643595] usb 3-1: Product: USB 2.0 Hub [MTT]
[ 3.643854] hub 3-1:1.0: USB hub found
[ 3.643904] hub 3-1:1.0: 4 ports detected
[ 3.820478] rockchip_i2c ff150000.i2c: i2c is not in idle(state = 3)
[ 3.820493] s5k4ec_back_3(rk_cam_sensor:167): write reg(0x2e, val:0x1a4) failed, try to write again!
[ 4.017282] rockchip_i2c ff150000.i2c: i2c is not in idle(state = 3)
[ 4.017296] s5k4ec_back_3(rk_cam_sensor:333): read reg(0xf12 val:0x0) failed, try to read again!
[ 4.017319] s5k4ec_back_3(rk_cam_sensor:716): error: mismatched pid = 0xffff
[ 4.017319]
ules/3.10.0/modules.dep: No such file or directory

请问还需要修改什么地方，
才能让FireFly-RK3288-Reload在ubuntu/linux可以支持DVP接口的s5k4ecgx摄像头？

112433gvzq7jqq70b80uoc.png (30.49 KB, 下载次数: 522)

作者: BLANK 时间: 2016-11-8 17:30
请问楼主解决问题没有，我也是遇到此问题，我这边是安卓环境，配置完并没有发现 dev下有新设备的出现

作者: leung先森 时间: 2016-11-9 11:29
linux底下的dvp接口可以参考这个
http://developer.t-firefly.com/f ... amp;page=1#pid21086

作者: carter123456 时间: 2017-8-31 19:08
请问楼主解决了没我用的是3128能在dev下面找打设备节点，但是通过V4L2读不到数据啊

作者: wx_Simon_WKj2r 时间: 2019-7-15 17:00

carter123456 发表于 2017-8-31 19:08
请问楼主解决了没我用的是3128能在dev下面找打设备节点，但是通过V4L2读不到数据啊

这个好像要用gst吧

欢迎光临 Firefly开源社区 (https://dev.t-firefly.com/)