Firefly开源社区

标题: RK3288 跑Android5.1一直重启 [打印本页]

作者: werren 时间: 2016-11-26 22:58
标题: RK3288 跑Android5.1一直重启
1. 编译后烧录映像update.img 在官方的rk3288-reload板子上可以正常启动，接HDMI到电脑显示器，还有鼠标键盘都能正常显示和操作；
2. 现在有一核心板搭建用于点屏的板子，烧录同样的update.img一直反复重启

问：
      A. 是何原因重启
      B. 如果我只要板子支触控LCD（MIPI interface）还有USB，SD卡访问是不是要把其余的外设（如HDMI）关掉，否则系统无法启动

贴上电到重启串口数据如下：
DDR Version 1.00 20150318
In
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Memory OK
Memory OK
OUT

U-Boot 2014.10-RK3288-10-g65679f1 (Jul 20 2015 - 10:28:11)

CPU: rk3288
CPU's clock information:
arm pll = 600000000HZ
periph pll = 300000000HZ
ddr pll = 200000000HZ
codec pll = 594000000HZ
Board: Rockchip platform Board
DRAM:  Found dram banks:1
Adding bank:0000000000000000(0000000080000000)
128 MiB
remotectl v0.1
storage init OK!
Using default environment

GetParam
check parameter success
failed to prepare fdt from boot!
power key: bank-0 pin-5
can't find dts node for ricoh619
can't find dts node for rk818
No pmic detect.
Can't find dts node for fuel guage cw201x
SecureBootEn = 0, SecureBootLock = 0

#Boot ver: 2015-07-20#2.19
empty serial no.
checkKey
vbus = 1
board_fbt_key_pressed: ir_keycode = 0x0, frt = 0
no fuel gauge found
no fuel gauge found
read logo_on switch from dts [1]
can't find power_ctr node for lcdc0
can't find dts node for deviceinfo
rk_hdmi_register:fail to read deviceinfo
hdmi baseparamer 0x0@0-0
Hdmi Devices Not Exist.
pll_src = 0, dclk_hz = 130000000, dclk_div = 4
load mipi dsi chip:rk_mipi_dsi.0 id:3133302a
mipi_dsi v1.3 2014-04-17
failed to find part:logo
no fuel gauge found
checkKey
vbus = 1
board_fbt_key_pressed: ir_keycode = 0x0, frt = 0
got recovery cmd from misc.
load fdt from resouce.
ERROR: [get_entry_ram]: Cannot find logo_kernel.bmp!
Secure Boot state: 0
kernel @ 0x02000000 (0x006ba878)
ramdisk  @ 0x05bf0000 (0x002c6754)
bootrk: do_bootm_linux...
Loading Device Tree to 05600000, end 0561c150 ... OK
Add bank:0000000000000000, 0000000080000000

Starting kernel ...

[ 0.000000] Booting Linux on physical CPU 0x500
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.10.0 (root@ubuntu) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #23 SMP PREEMPT Thu Nov 24 21:53:16 CST 2016
[ 0.000000] CPU: ARMv7 Processor [410fc0d1] revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Rockchip RK3288 (Flattened Device Tree), model: rockchip,rk3288
[ 0.000000] rockchip_uboot_logo_setup: mem: 0x02000000@0x7dc00000, offset:0x00000000
[ 0.000000] hdmi init vic is -1
[ 0.000000] rockchip_uboot_mem_reserve: reserve 0x02000000@0x7dc00000 for uboot logo
[ 0.000000] rockchip_ion_reserve
[ 0.000000] ion heap(drm): base(0) size(0) align(0)
[ 0.000000] ion heap(cma): base(0) size(28000000) align(0)
[ 0.000000] ion heap(vmalloc): base(0) size(0) align(0)
[ 0.000000] cma: CMA: reserved 640 MiB at 55c00000
[ 0.000000] ion_reserve: cma reserved base 55c00000 size 671088640
[ 0.000000] cma: CMA: reserved 16 MiB at 1f000000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] Boot mode: RECOVERY (2) flag: RECOVER (0xc3524203)
[ 0.000000] PERCPU: Embedded 9 pages/cpu @c1f5a000 s13376 r8192 d15296 u36864
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 523264
[ 0.000000] Kernel command line: vmalloc=496M console=ttyS2 androidboot.selinux=permissive androidboot.hardware=rk30board androidboot.console=ttyS2 init=/init  mtdparts=rk29xxnand:0x00002000@0x00000000(parameter),0x00002000@0x00002000(uboot),0x00002000@0x00004000(misc),0x00008000@0x00006000(resource),0x00008000@0x0000e000(kernel),0x00010000@0x00016000(boot),0x00010000@0x00026000(recovery),0x0001a000@0x00036000(backup),0x00040000@0x00050000(cache),0x00002000@0x00090000(kpanic),0x00300000@0x00092000(system),0x00008000@0x00392000(metadata),0x00002000@0x0039A000(baseparamer),0x00200000@0x0039C000(userdata),0x00020000@0x0059C000(radical_update),-@0x005BC000(user) storagemedia=emmc uboot_logo=0x02000000@0x7dc00000 loader.timestamp=2015-07-20_10:28:11 hdmi.vic=-1
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] allocated 4194304 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 2048MB = 2048MB total
[ 0.000000] Memory: 1352904k/1352904k available, 744248k reserved, 884736K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000]    vector  : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000]    fixmap  : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000]    vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
[ 0.000000]    lowmem  : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000]    pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000]    modules : 0xbf000000 - 0xbfe00000 (  14 MB)
[ 0.000000]    .text : 0xc0008000 - 0xc0bb2a34 (11947 kB)
[ 0.000000]    .init : 0xc0bb3000 - 0xc0c4a440 ( 606 kB)
[ 0.000000]    .data : 0xc0c4c000 - 0xc0ddea40 (1611 kB)
[ 0.000000]       .bss : 0xc0ddea40 - 0xc0effb3c (1157 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] rk_clk_tree_init start!
[ 0.000000] rkclk: _rkclk_add_provider: fail to get ehci1phy_12m_div
[ 0.000000] rkclk: rkclk_cache_parents: ehci1phy_12m_div clk_get error
[ 0.000000] rk_get_uboot_display_flag: uboot_logo_on = 1
[ 0.000000] rkclk_init_clks: cnt_parent = 7
[ 0.000000] rkclk_init_clks: cnt_rate = 28
[ 0.000000] rk3288 set GPLL BW 20 for HDMI!
[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] Switching to timer-based delay loop
[ 0.000000] sched_clock: ARM arch timer >56 bits at 24000kHz, resolution 41ns
[ 0.000000] process version: 3
[ 0.000000] channel:0, lkg:13
[ 0.000000] target-temp:80
[ 0.000000] channel:2, lkg:0
[ 0.000000] channel:0, lkg:13
[ 0.000000] channel:1, lkg:12
[ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
[ 0.341647] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.341663] pid_max: default: 32768 minimum: 301
[ 0.341778] Security Framework initialized
[ 0.341793] SELinux:  Initializing.
[ 0.341866] Mount-cache hash table entries: 512
[ 0.342509] Initializing cgroup subsys debug
[ 0.342524] Initializing cgroup subsys memory
[ 0.342552] Initializing cgroup subsys freezer
[ 0.342579] CPU: Testing write buffer coherency: ok
[ 0.342898] /cpus/cpu@0 missing clock-frequency property
[ 0.342911] /cpus/cpu@1 missing clock-frequency property
[ 0.342921] /cpus/cpu@2 missing clock-frequency property
[ 0.342930] /cpus/cpu@3 missing clock-frequency property
[ 0.342981] CPU0: thread -1, cpu 0, socket 5, mpidr 80000500
[ 0.343031] Setting up static identity map for 0xc085ce28 - 0xc085ce80
[ 0.345490] last_log: 0x1e900000 map to 0xe0804000 and copy to 0xe0886000, size 0x80000 early 0x1878 (version 3.1)
[ 0.419765] CPU1: Booted secondary processor
[ 0.419799] CPU1: thread -1, cpu 1, socket 5, mpidr 80000501
[ 0.439436] CPU2: Booted secondary processor
[ 0.439462] CPU2: thread -1, cpu 2, socket 5, mpidr 80000502
[ 0.459148] CPU3: Booted secondary processor
[ 0.459172] CPU3: thread -1, cpu 3, socket 5, mpidr 80000503
[ 0.459273] Brought up 4 CPUs
[ 0.459302] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[ 0.459311] CPU: All CPU(s) started in SVC mode.
[ 0.460049] devtmpfs: initialized
[ 0.464370] VFP support v0.3: implementor 41 architecture 3 part 30 variant d rev 0
[ 0.465446] pinctrl core: initialized pinctrl subsystem
[ 0.465697] regulator-dummy: no parameters
[ 0.490269] NET: Registered protocol family 16
[ 0.492088] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.492481] ion_snapshot: 0x1eaa0000 map to 0xe0907000 and copy to 0xc0edae4c (version 0.1)
[ 0.492730] Registered FIQ tty driver
[ 0.493131] fiq-debugger is disabled in device tree
[ 0.493819] rockchip_get_bank_data:name=base start=0xff750000,end=0xff7500ff
[ 0.493841] rockchip_get_bank_data:name=mux_bank0 start=0xff730084,end=0xff73008f
[ 0.493858] rockchip_get_bank_data:name=pull_bank0 start=0xff730064,end=0xff73006f
[ 0.493875] rockchip_get_bank_data:name=drv_bank0 start=0xff730070,end=0xff73007b
[ 0.493966] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio1@ff780000 start=0xff780000,end=0xff7800ff
[ 0.494029] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio2@ff790000 start=0xff790000,end=0xff7900ff
[ 0.494090] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio3@ff7a0000 start=0xff7a0000,end=0xff7a00ff
[ 0.494152] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio4@ff7b0000 start=0xff7b0000,end=0xff7b00ff
[ 0.494214] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio5@ff7c0000 start=0xff7c0000,end=0xff7c00ff
[ 0.494276] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio6@ff7d0000 start=0xff7d0000,end=0xff7d00ff
[ 0.494338] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio7@ff7e0000 start=0xff7e0000,end=0xff7e00ff
[ 0.494399] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio8@ff7f0000 start=0xff7f0000,end=0xff7f00ff
[ 0.494467] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio15@ff7f2000 start=0xff7f2000,end=0xff7f20ff
[ 0.494530] rockchip_pinctrl_probe:name=RK3288-GPIO,type=3
[ 0.494543] rockchip_pinctrl_probe:name=base start=0xff770000,end=0xff77013f
[ 0.494554] rockchip_pinctrl_probe:name=pull start=0xff770140,end=0xff7701bf
[ 0.494565] rockchip_pinctrl_probe:name=drv start=0xff7701c0,end=0xff77023f
[ 0.495177] rockchip_interrupts_register:bank_num=7
[ 0.497096] of_get_gpio_init_config:gpio[0] = 256, value = 0
[ 0.497116] of_get_gpio_init_config:gpio[1] = 136, value = 0
[ 0.497167] rockchip_pinctrl_probe:init ok
[ 0.504050] rk_iommu ff900800.iep_mmu: (iep) Enter
[ 0.504138] rk_iommu ff900800.iep_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.504151] rk_iommu ff900800.iep_mmu: (iep) Initialized
[ 0.504318] rk_iommu ff950800.vip_mmu: (vip) Enter
[ 0.504389] rk_iommu ff950800.vip_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.504402] rk_iommu ff950800.vip_mmu: (vip) Initialized
[ 0.504566] rk_iommu ff930300.vopb_mmu: (vopb) Enter
[ 0.504638] rk_iommu ff930300.vopb_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.504651] rk_iommu ff930300.vopb_mmu: (vopb) Initialized
[ 0.504810] rk_iommu ff940300.vopl_mmu: (vopl) Enter
[ 0.504881] rk_iommu ff940300.vopl_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.504893] rk_iommu ff940300.vopl_mmu: (vopl) Initialized
[ 0.505066] rk_iommu ff9c0440.hevc_mmu: (hevc) Enter
[ 0.505142] rk_iommu ff9c0440.hevc_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.505155] rk_iommu ff9c0440.hevc_mmu: (hevc) Initialized
[ 0.505316] rk_iommu ff9a0800.vpu_mmu: (vpu) Enter
[ 0.505390] rk_iommu ff9a0800.vpu_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.505402] rk_iommu ff9a0800.vpu_mmu: (vpu) Initialized
[ 0.505577] rk_iommu ff914000.isp_mmu: (isp_mmu) Enter
[ 0.505656] rk_iommu ff914000.isp_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.505669] rk_iommu ff914000.isp_mmu: (isp_mmu) Initialized
[ 0.507752] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.507765] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.508360] rk3368_init_rockchip_pmu_ops: could not find pmu dt node
[ 0.508383] DDR DEBUG: version 1.00 20150126
[ 0.508433] DDR DEBUG: Channel a:
[ 0.508442] DDR DEBUG: DDR3 Device
[ 0.508455] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Total Capability=1024MB
[ 0.508464] DDR DEBUG: Channel b:
[ 0.508471] DDR DEBUG: DDR3 Device
[ 0.508483] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Total Capability=1024MB
[ 0.508492] DDR DEBUG: addr=0xde8000
[ 0.508502] DDR DEBUG: stride=9, size=256, halfcap=40000000
[ 0.508510] DDR DEBUG: socAddr[0]=0xde8000, socAddr[1]=0xde8100
[ 0.508519] DDR DEBUG: chAddr[0]=0xde8000, chAddr[1]=0xde8000
[ 0.508531] DDR DEBUG: dtar[0]=0x1bd000, dtar[1]=0x1bd000
[ 0.508584] DDR DEBUG: init success!!! freq=200MHz
[ 0.508592] DDR DEBUG: Channel a:
[ 0.508604] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.508616] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.508629] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.508641] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.508653] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0
[ 0.508662] DDR DEBUG: DRV Pull-Up=0x19, DRV Pull-Dwn=0x19
[ 0.508671] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2
[ 0.508678] DDR DEBUG: Channel b:
[ 0.508690] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.508702] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.508715] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.508726] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
[ 0.508737] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0
[ 0.508746] DDR DEBUG: DRV Pull-Up=0x19, DRV Pull-Dwn=0x19
[ 0.508755] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2
[ 0.533225] bio: create slab <bio-0> at 0
[ 0.533772] Rockchip hdmi driver version 2.0
[ 0.533772] .
[ 0.535003] SCSI subsystem initialized
[ 0.535162] usbcore: registered new interface driver usbfs
[ 0.535207] usbcore: registered new interface driver hub
[ 0.535297] usbcore: registered new device driver usb
[ 0.538041] rockchip_i2c ff650000.i2c: i2c-0: Rockchip I2C adapter
[ 0.538526] rockchip_i2c ff140000.i2c: i2c-1: Rockchip I2C adapter
[ 0.538972] rockchip_i2c ff660000.i2c: i2c-2: Rockchip I2C adapter
[ 0.539220] rockchip_i2c ff150000.i2c: i2c-3: Rockchip I2C adapter
[ 0.540358] rockchip_i2c ff160000.i2c: i2c-4: Rockchip I2C adapter
[ 0.540506] media: Linux media interface: v0.10
[ 0.540547] Linux video capture interface: v2.00
[ 0.540603] pps_core: LinuxPPS API ver. 1 registered
[ 0.540613] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.540632] PTP clock support registered
[ 0.540692] i2c-core: driver [bq24296] using legacy suspend method
[ 0.540701] i2c-core: driver [bq24296] using legacy resume method
[ 0.541420] ion_drm_heap_create: 0@0
[ 0.541551] Rockchip ion module is successfully loaded (v1.1)
[ 0.541722] Advanced Linux Sound Architecture Driver Initialized.
[ 0.542149] Bluetooth: Core ver 2.16
[ 0.542186] NET: Registered protocol family 31
[ 0.542196] Bluetooth: HCI device and connection manager initialized
[ 0.542212] Bluetooth: HCI socket layer initialized
[ 0.542225] Bluetooth: L2CAP socket layer initialized
[ 0.542252] Bluetooth: SCO socket layer initialized
[ 0.542491] cfg80211: Calling CRDA to update world regulatory domain
[ 0.543695] act8846_i2c_probe,line=898
[ 0.545182] act8846 set 0xf4 error!
[ 0.545272] act8846: probe of 0-005a failed with error -11
[ 0.549808] vdd_arm: 712 <--> 1500 mV at 1000 mV
[ 0.550818] The device is not syr82x fffffff5
[ 0.550836] syr82x: probe of 0-0041 failed with error -11
[ 0.551309] rk808_i2c_probe,line=1355
[ 0.552655] The device is not rk808 -11
[ 0.552725] rk808: probe of 0-001b failed with error -11
[ 0.552804] i2c-core: driver [rk818] using legacy suspend method
[ 0.552813] i2c-core: driver [rk818] using legacy resume method
[ 0.554498] Switching to clocksource arch_sys_counter
[ 0.578303] rga: Module initialized.
[ 0.579030] rga2 ff920000.rga: rga ion client create success!
[ 0.579204] rga: Driver loaded succesfully
[ 0.579412] fb disp policy is box
[ 0.579453] rk-fb rockchip-fb: rk fb ion client create success!
[ 0.579465] rk-fb rockchip-fb: rockchip framebuffer driver probe
[ 0.579773] rk-screen rk_screen.8: rockchip screen probe success
[ 0.579939] rk32-lvds ff96c000.lvds: screen is not lvds/rgb!
[ 0.579961] rk32-lvds: probe of ff96c000.lvds failed with error -22
[ 0.580327] rk32-edp ff970000.edp: screen is not edp!
[ 0.580343] rk32-edp: probe of ff970000.edp failed with error -22
[ 0.580517] rk32-dsi
[ 0.580660] dsi->host.irq =51
[ 0.580678] load mipi dsi chip:rk_mipi_dsi.0 id:3133302a
[ 0.580686] mipi_dsi v1.3 2014-04-17
[ 0.580750] rk32-mipi ff960000.mipi: rk mipi_dsi probe success!
[ 0.580762] rk32-mipi ff960000.mipi: rockchip mipi_dsi v1.1 2014-06-17
[ 0.581314] rk3288-lcdc lcdc0: can't find power_ctr node for lcdc0
[ 0.581539] graphics fb0: rockchip framebuffer registerd:fb0
[ 0.581845] graphics fb1: rockchip framebuffer registerd:fb1
[ 0.582015] graphics fb2: rockchip framebuffer registerd:fb2
[ 0.582173] graphics fb3: rockchip framebuffer registerd:fb3
[ 0.582878] rk3288-lcdc lcdc0: lcdc0: dclk:130000000>>fps:50
[ 0.582894] rk3288-lcdc lcdc0: wakeup from standby!
[ 0.614696] alloc_buffer:ion_phy_addr=0x10000000
[ 0.628060] fb0:phy:10000000>>vir:e0991000>>len:0x1900000
[ 0.635783] rk_battery_charger_detect_cb , battery_charger_detect 1
[ 0.642471] rk_iommu ff930300.vopb_mmu: rockchip_iommu_attach_device: Attached new IOMMU with pgtable 0x1eabb000
[ 0.642504] rk3288-lcdc lcdc0: lcdc0 probe ok, iommu enabled
[ 0.642717] rk3288-lcdc lcdc1: can't find power_ctr node for lcdc1
[ 0.642729] rk_fb_trsm_ops_get:un supported transmitter:0!
[ 0.643000] graphics fb4: rockchip framebuffer registerd:fb4
[ 0.643404] graphics fb5: rockchip framebuffer registerd:fb5
[ 0.643575] graphics fb6: rockchip framebuffer registerd:fb6
[ 0.643743] graphics fb7: rockchip framebuffer registerd:fb7
[ 0.644462] unknow screen type: 0
[ 0.644532] rk3288-lcdc lcdc1: lcdc1: dclk:130000000>>fps:881
[ 0.644546] rk3288-lcdc lcdc1: wakeup from standby!
[ 0.648467] fb4:phy:10000000>>vir:e0991000>>len:0x1900000
[ 0.648482] rk3288-lcdc lcdc1: lcdc1 probe ok, iommu enabled
[ 0.649389] rockchip_set_mux:warning ignore bank num 15
[ 0.649516] rockchip_set_mux:warning ignore bank num 15
[ 0.649627] rockchip_set_mux:warning ignore bank num 15
[ 0.649749] rockchip_set_mux:warning ignore bank num 15
[ 0.649859] rockchip_set_mux:warning ignore bank num 15
[ 0.649974] rockchip_set_mux:warning ignore bank num 15
[ 0.650089] rockchip_set_mux:warning ignore bank num 15
[ 0.650207] rockchip_set_mux:warning ignore bank num 15
[ 0.650335] rockchip_set_mux:warning ignore bank num 15
[ 0.650480] rockchip_set_mux:warning ignore bank num 15
[ 0.651993] NET: Registered protocol family 2
[ 0.652667] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.652742] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.652815] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.652873] TCP: reno registered
[ 0.652888] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.652911] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.653142] NET: Registered protocol family 1
[ 0.653793] Unpacking initramfs...
[ 0.793038] Freeing initrd memory: 2840K (c5bf0000 - c5eb6000)
[ 0.793818] hw perfevents: enabled with ARMv7 Cortex-A12 PMU driver, 7 counters available
[ 0.794434] vcodec_service: probe device ff9a0000.vpu_service
[ 0.794628] vcodec_service: No reset resource define
[ 0.794802] vcodec_service: ff9a0000.vpu_service: power on
[ 0.794911] vcodec_service: probe device ff9a0000.vpu_service
[ 0.794926] vcodec_service: checking hw id 4831
[ 0.795888] vcodec_service: ff9a0000.vpu_service: power off...
[ 0.795935] vcodec_service: done
[ 0.795944] vcodec_service: init success
[ 0.796012] vcodec_service: probe device ff9c0000.hevc_service
[ 0.796371] vcodec_service: ff9c0000.hevc_service: power on
[ 0.796434] vcodec_service: probe device ff9c0000.hevc_service
[ 0.796448] vcodec_service: checking hw id 6867
[ 0.796706] vcodec_service: ff9c0000.hevc_service: power off...
[ 0.796746] vcodec_service: done
[ 0.796754] vcodec_service: init success
[ 0.796901] rknandbase v1.0 2014-03-31
[ 0.797032] rknand: probe of ff400000.nandc failed with error -1
[ 0.797153] rknand_driver:ret = 0
[ 0.798389] audit: initializing netlink socket (disabled)
[ 0.798439] type=2000 audit(0.450:1): initialized
[ 0.799282] bounce pool size: 64 pages
[ 0.803984] fuse init (API version 7.22)
[ 0.804344] msgmni has been set to 951
[ 0.806146] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 0.806163] io scheduler noop registered
[ 0.806172] io scheduler deadline registered
[ 0.806268] io scheduler cfq registered (default)
[ 0.806910] pwm-backlight backlight.20: unable to request PWM, trying legacy API
[ 0.806924] pwm-backlight backlight.20: unable to request legacy PWM
[ 0.806950] platform backlight.20: Driver pwm-backlight requests probe deferral
[ 0.807693] rockchip-hdmiv2 ff980000.hdmi: rockchip hdmiv2 probe sucess.
[ 0.808396] IEP Driver loaded succesfully
[ 0.808490] Module initialized.
[ 0.809319] dma-pl330 ffb20000.pdma: Loaded driver for PL330 DMAC-2364208
[ 0.809338] dma-pl330 ffb20000.pdma: DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10
[ 0.810775] dma-pl330 ff250000.pdma: Loaded driver for PL330 DMAC-2364208
[ 0.810793] dma-pl330 ff250000.pdma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[ 0.811079] pwm-voltage-regulator pwm_regulator.27: unable to request PWM, trying legacy API
[ 0.811094] pwm-voltage-regulator pwm_regulator.27: unable to request legacy PWM
[ 0.811102] pwm_regulator_probe:error
[ 0.811138] platform pwm_regulator.27: Driver pwm-voltage-regulator requests probe deferral
[ 0.811336] rk_serial.c v1.8 2014-03-04
[ 0.811564] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 87) is a rk29_serial.0
[ 0.811755] serial ff180000.serial: membase e0972000
[ 0.811923] ff190000.serial: ttyS1 at MMIO 0xff190000 (irq = 88) is a rk29_serial.1
[ 0.812129] serial ff190000.serial: membase e097e000
[ 0.812293] ff690000.serial: ttyS2 at MMIO 0xff690000 (irq = 89) is a rk29_serial.2
[ 0.812383] 2, baud is:115200
[ 0.813925] console [ttyS2] enabled
[ 0.814127] serial ff690000.serial: membase fed60000
[ 0.814316] ff1b0000.serial: ttyS3 at MMIO 0xff1b0000 (irq = 90) is a rk29_serial.3
[ 0.814503] serial ff1b0000.serial: membase e42be000
[ 0.817309] loop: module loaded
[ 0.817671] zram: Created 1 device(s) ...
[ 0.817760] i2c-core: driver [mpu6050B1] using legacy suspend method
[ 0.817773] i2c-core: driver [mpu6050B1] using legacy resume method
[ 0.817791] mpu_init: Probe name mpu6050B1
[ 0.817965] ak8963_mod_init: Probe name ak8963_mod
[ 0.818687] SCSI Media Changer driver v0.25
[ 0.818935] dws->regs: e42e2000
[ 0.820141] rockchip_spi_probe:num_cs=2,bus_num=0,irq=76,freq=45692308 ok
[ 0.820472] tun: Universal TUN/TAP device driver, 1.6
[ 0.820485] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.820613] vmac_init.
[ 0.821187] stmmac_probe_config_dt: Can not read property: pmu_regulator.
[ 0.821203] stmmac_probe_config_dt: clock input/output? (input).
[ 0.821217] stmmac_probe_config_dt: TX delay(0x30).
[ 0.821229] stmmac_probe_config_dt: RX delay(0x20).
[ 0.821278] stmmac_probe_config_dt: is rockchip,rk3288-gmac
[ 0.821289] stmmc_pltfr_init:
[ 0.821299] stmmc_pltfr_init: ERROR: Get power-gpio failed.
[ 0.821321] gmac_phy_reset: ERROR: Request pin stmmc_pltfr_init failed.
[ 0.821333] stmmc_pltfr_init: init for RGMII
[ 0.821343] tx delay=0x30
[ 0.821343] rx delay=0x20
[ 0.821359] tx delay=0x30
[ 0.821359] rx delay=0x20
[ 0.821803] stmmac - user ID: 0x10, Synopsys ID: 0x35
[ 0.821814]  Normal descriptors
[ 0.821824]  Ring mode enabled
[ 0.821835]  DMA HW capability register supported
[ 0.821846]  RX Checksum Offload Engine supported (type 2)
[ 0.821856]  TX Checksum insertion supported
[ 0.821865]  Wake-Up On Lan supported
[ 0.821905]  Enable RX Mitigation via HW Watchdog Timer
[ 0.822368] PPP generic driver version 2.4.2
[ 0.822525] PPP BSD Compression module registered
[ 0.822539] PPP Deflate Compression module registered
[ 0.822562] PPP MPPE Compression module registered
[ 0.822575] NET: Registered protocol family 24
[ 0.822612] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[ 0.822625] CSLIP: code copyright 1989 Regents of the University of California.
[ 0.822639] Rockchip WiFi SYS interface (V1.00) ...
[ 0.822681] esp_mem_init enter date Nov 23 2016 17:29:10
[ 0.822693] esp_mem_init VERSION [V2.5]
[ 0.822736] esp_mem_init complete
[ 0.822823] usbcore: registered new interface driver catc
[ 0.822866] usbcore: registered new interface driver kaweth
[ 0.822879] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[ 0.822919] usbcore: registered new interface driver pegasus
[ 0.822959] usbcore: registered new interface driver rtl8150
[ 0.823001] usbcore: registered new interface driver r8152
[ 0.823013] hso: drivers/net/usb/hso.c: Option Wireless
[ 0.823085] usbcore: registered new interface driver hso
[ 0.823139] usbcore: registered new interface driver asix
[ 0.823181] usbcore: registered new interface driver ax88179_178a
[ 0.823223] usbcore: registered new interface driver cdc_ether
[ 0.823270] usbcore: registered new interface driver cdc_eem
[ 0.823308] usbcore: registered new interface driver dm9601
[ 0.823343] usbcore: registered new interface driver dm9620
[ 0.823395] usbcore: registered new interface driver smsc75xx
[ 0.823444] usbcore: registered new interface driver smsc95xx
[ 0.823484] usbcore: registered new interface driver gl620a
[ 0.823521] usbcore: registered new interface driver net1080
[ 0.823558] usbcore: registered new interface driver plusb
[ 0.823597] usbcore: registered new interface driver rndis_host
[ 0.823634] usbcore: registered new interface driver cdc_subset
[ 0.823675] usbcore: registered new interface driver zaurus
[ 0.823717] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[ 0.823779] usbcore: registered new interface driver int51x1
[ 0.823818] usbcore: registered new interface driver kalmia
[ 0.823856] usbcore: registered new interface driver ipheth
[ 0.823898] usbcore: registered new interface driver sierra_net
[ 0.823942] usbcore: registered new interface driver cx82310_eth
[ 0.823994] usbcore: registered new interface driver cdc_ncm
[ 0.824035] usbcore: registered new interface driver qmi_wwan
[ 0.824074] usbcore: registered new interface driver cdc_mbim
[ 0.824086] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.826527] EHCI: ehci_rk_probe e4340000 e4340010
[ 0.826545] rockchip_ehci_host ff500000.usb: EHCI Host Controller
[ 0.826576] rockchip_ehci_host ff500000.usb: new USB bus registered, assigned bus number 1
[ 0.826909] rockchip_ehci_host ff500000.usb: irq 56, io mem 0xff500000
[ 0.839946] rockchip_ehci_host ff500000.usb: USB 2.0 started, EHCI 1.00
[ 0.840028] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.840046] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.840061] usb usb1: Product: EHCI Host Controller
[ 0.840075] usb usb1: Manufacturer: Linux 3.10.0 ehci_hcd
[ 0.840089] usb usb1: SerialNumber: ff500000.usb
[ 0.840555] hub 1-0:1.0: USB hub found
[ 0.840581] hub 1-0:1.0: 1 port detected
[ 0.840748] EHCI: ehci_rk_probe ok
[ 0.840872] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.841086] usbcore: registered new interface driver cdc_acm
[ 0.841100] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 0.841154] usbcore: registered new interface driver usblp
[ 0.841196] usbcore: registered new interface driver cdc_wdm
[ 0.841263] usbcore: registered new interface driver usb-storage
[ 0.841330] usbcore: registered new interface driver ums-alauda
[ 0.841372] usbcore: registered new interface driver ums-cypress
[ 0.841412] usbcore: registered new interface driver ums-datafab
[ 0.841450] usbcore: registered new interface driver ums_eneub6250
[ 0.841488] usbcore: registered new interface driver ums-freecom
[ 0.841529] usbcore: registered new interface driver ums-isd200
[ 0.841567] usbcore: registered new interface driver ums-jumpshot
[ 0.841604] usbcore: registered new interface driver ums-karma
[ 0.841642] usbcore: registered new interface driver ums-onetouch
[ 0.841681] usbcore: registered new interface driver ums-sddr09
[ 0.841720] usbcore: registered new interface driver ums-sddr55
[ 0.841763] usbcore: registered new interface driver ums-usbat
[ 0.841858] usbcore: registered new interface driver usbserial
[ 0.841899] usbcore: registered new interface driver usbserial_generic
[ 0.841932] usbserial: USB Serial support registered for generic
[ 0.841972] usbcore: registered new interface driver option
[ 0.842003] usbserial: USB Serial support registered for GSM modem (1-port)
[ 0.842076] usbcore: registered new interface driver trancevibrator
[ 0.842090] usb20_otg: version 3.10a 21-DEC-2012
[ 0.842548] e4380040
[ 0.842563] Core Release: 3.10a
[ 0.842576] Setting default values for core params
[ 0.842714] Using Buffer DMA mode
[ 0.842726] Periodic Transfer Interrupt Enhancement - disabled
[ 0.842737] Multiprocessor Interrupt Enhancement - disabled
[ 0.842750] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 0.842760] ^^^^^^^^^^^^^^^^^Device Mode
[ 0.842775] Dedicated Tx FIFOs mode
[ 0.842795] pcd_init otg_dev = ddf8d080
[ 0.842950] usb20_otg ff580000.usb: DWC OTG Controller
[ 0.842979] usb20_otg ff580000.usb: new USB bus registered, assigned bus number 2
[ 0.843010] usb20_otg ff580000.usb: irq 55, io mem 0x00000000
[ 0.843073] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.843090] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.843104] usb usb2: Product: DWC OTG Controller
[ 0.843117] usb usb2: Manufacturer: Linux 3.10.0 dwc_otg_hcd
[ 0.843130] usb usb2: SerialNumber: ff580000.usb
[ 0.843564] hub 2-0:1.0: USB hub found
[ 0.843588] hub 2-0:1.0: 1 port detected
[ 0.843917] usb20_host: version 3.10a 21-DEC-2012
[ 0.846452] e4400040
[ 0.846465] Core Release: 3.10a
[ 0.846482] Setting default values for core params
[ 0.846605] Using Buffer DMA mode
[ 0.846617] Periodic Transfer Interrupt Enhancement - disabled
[ 0.846627] Multiprocessor Interrupt Enhancement - disabled
[ 0.846638] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 0.846648] ^^^^^^^^^^^^^^^^^^Host Mode
[ 0.846675] usb20_host ff540000.usb: DWC OTG Controller
[ 0.846705] usb20_host ff540000.usb: new USB bus registered, assigned bus number 3
[ 0.846735] usb20_host ff540000.usb: irq 57, io mem 0x00000000
[ 0.846828] Init: Power Port (0)
[ 0.846887] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.846904] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.846918] usb usb3: Product: DWC OTG Controller
[ 0.846931] usb usb3: Manufacturer: Linux 3.10.0 dwc_otg_hcd
[ 0.846944] usb usb3: SerialNumber: ff540000.usb
[ 0.847356] hub 3-0:1.0: USB hub found
[ 0.847379] hub 3-0:1.0: 1 port detected
[ 0.848137] usbcore: registered new interface driver xpad
[ 0.848198] usbcore: registered new interface driver usb_acecad
[ 0.848246] usbcore: registered new interface driver aiptek
[ 0.848292] usbcore: registered new interface driver gtco
[ 0.848344] usbcore: registered new interface driver hanwang
[ 0.848390] usbcore: registered new interface driver kbtab
[ 0.848444] usbcore: registered new interface driver wacom
[ 0.848574] ==gsl_ts_init==
[ 0.848624] ret=0
[ 0.848905] sensor_register_slave:mma8452,id=17
[ 0.848919] sensor_register_slave:gs_mc3230,id=23
[ 0.848929] gsensor_init
[ 0.848940] sensor_register_slave:mpu6880_acc,id=24
[ 0.848951] sensor_register_slave:mpu6500_acc,id=25
[ 0.848962] sensor_register_slave:cm3217,id=48
[ 0.848974] sensor_register_slave:cm3218,id=49
[ 0.849218] .. rk pwm remotectl v1.1 init
[ 0.849470] input: ff680000.pwm as /devices/ff680000.pwm/input/input0
[ 0.852895] rtc_hym8563 0-0051: clock/calendar information is no longer guaranteed
[ 0.863567] rtc_hym8563 0-0051: rtc core: registered hym8563 as rtc0
[ 0.863639] i2c /dev entries driver
[ 0.864343] IR NEC protocol handler initialized
[ 0.864357] IR RC5(x) protocol handler initialized
[ 0.864368] IR RC6 protocol handler initialized
[ 0.864378] IR JVC protocol handler initialized
[ 0.864388] IR Sony protocol handler initialized
[ 0.864398] IR RC5 (streamzap) protocol handler initialized
[ 0.864408] IR SANYO protocol handler initialized
[ 0.864418] IR MCE Keyboard/mouse protocol handler initialized
[ 0.864575] usbcore: registered new interface driver uvcvideo
[ 0.864587] USB Video Class driver (1.1.1)
[ 0.864600] CamSys driver version: v0.32.0,  CamSys head file version: v0.11.0
[ 0.866140] D1:camsys_platform_probe(1300): 1-gpios-cifpower: gpio=236
[ 0.866164] D1:camsys_platform_probe(1303): gpios-cifpower: gpio_request
[ 0.866185] D1:camsys_platform_probe(1305): 1-gpios-cifpower: gpio_request=0
[ 0.866207] D1:camsys_platform_probe(1314): gpios-cifpower: 236 high
[ 0.866245] D1:camsys_mipiphy_probe_cb(115): compatible is rockchip,rk3288
[ 0.866245]
[ 0.866315] D1:camsys_mipiphy_probe_cb(186): ff910000.isp mipi phy0 probe success(reg_phy: 0x0  reg_vir: 0x0  size: 0x0)
[ 0.866461] D1:camsys_mipiphy_probe_cb(183): ff910000.isp mipi phy1 probe success(reg_phy: 0xff968000  reg_vir: 0xe42f8000  size: 0x4000)
[ 0.867102] D1:camsys_platform_probe(1447): ff910000.isp memory:
[ 0.867121] D1:camsys_platform_probe(1457):    Register memory (phy: 0xff910000 vir: 0xe4320000 size: 0x10000)
[ 0.867138] D1:camsys_platform_probe(1452):    I2c memory (phy: 0x1df3a000 vir: 0xddf3a000 size: 0x1000)
[ 0.867153] D1:camsys_init_ext_fsh_module(20): init external flash module
[ 0.867165] D1:camsys_platform_probe(1472): Probe ff910000.isp device success
[ 0.867659] not find test_power_init dev node
[ 0.867717] i2c-core: driver [bq27320] using legacy suspend method
[ 0.867729] i2c-core: driver [bq27320] using legacy resume method
[ 0.868094] rockchip_temp_probe,line=364
[ 0.918646] tsadc ff280000.tsadc: initialized
[ 0.919023] device-mapper: uevent: version 1.0.3
[ 0.919267] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[ 0.919564] Bluetooth: HCI UART driver ver 2.2
[ 0.919580] Bluetooth: HCI H4 protocol initialized
[ 0.919592] Bluetooth: HCILL protocol initialized
[ 0.919604] rtk_btusb: Realtek Bluetooth USB driver module init, version 2.21
[ 0.919616] rtk_btusb: Register usb char device interface for BT driver
[ 0.919808] usbcore: registered new interface driver rtk_btusb
[ 0.919869] DVFS ERR: clk_enable_dvfs: vd(vd_logic) can't get regulator(vdd_logic)!
[ 0.919895] DVFS ERR: clk_enable_dvfs: vd(vd_gpu) can't get regulator(vdd_gpu)!
[ 0.919911] DVFS ERR: clk_enable_dvfs: vd(vd_logic) can't get regulator(vdd_logic)!
[ 0.920552] cpufreq version 1.0, suspend freq 1200 MHz
[ 0.920744] cpuidle: using governor ladder
[ 0.920757] cpuidle: using governor menu
[ 0.920794] Synopsys Designware Multimedia Card Interface Driver
[ 0.920805] MHSC version = Ver 2.00 2015-06-10
[ 0.921124] dw cru_regsbase addr 0x1d8.
[ 0.921137] dw cru_reset_offset val 3.
[ 0.921152] dwmmc_rockchip ff0f0000.rksdmmc: Version ID is 270a
[ 0.921197] dwmmc_rockchip ff0f0000.rksdmmc: failed to get hpclk_mmc
[ 0.921509] dwmmc_rockchip ff0f0000.rksdmmc: Using internal DMA controller.
[ 0.921703] dw_mci_init_slot: fmin=400000, fmax=100000000 [mmc0]
[ 0.921830] 1358..dw_mci_set_ios:  no card. [mmc0]
[ 0.938386] 1358..dw_mci_set_ios:  no card. [mmc0]
[ 0.958092] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out 800000Hz for init[mmc0]
[ 0.958134] dwmmc_rockchip ff0f0000.rksdmmc: DW MMC controller at irq 67, 32 bit host data width, 256 deep fifo
[ 0.958154] dwmmc_rockchip ff0f0000.rksdmmc: 1 slots initialized
[ 0.958493] dw cru_regsbase addr 0x1d8.
[ 0.958526] dw cru_reset_offset val 0.
[ 0.958541] dwmmc_rockchip ff0c0000.rksdmmc: Version ID is 270a
[ 0.958583] dwmmc_rockchip ff0c0000.rksdmmc: failed to get hpclk_mmc
[ 0.959006] dwmmc_rockchip ff0c0000.rksdmmc: Using internal DMA controller.
[ 0.959194] dw_mci_init_slot: fmin=300000, fmax=50000000 [mmc1]
[ 0.959283] mmc1: no vmmc regulator found
[ 0.959422] dwmmc_rockchip ff0c0000.rksdmmc: mmc1: No udbg pinctrl found!
[ 0.959542] 1358..dw_mci_set_ios:  no card. [mmc1]
[ 0.977692] 1358..dw_mci_set_ios:  no card. [mmc1]
[ 0.990151] mmc0: BKOPS_EN bit is not set
[ 0.992025] rk_sdmmc: BOOT Bus speed=0Hz,Bus width=8bits.[mmc0]
[ 0.994307] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0)
[ 0.994331] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out normal clock [mmc0]
[ 0.994350] [mmc0] tuning regsbase addr 0x218.
[ 0.994876] [mmc0] Data transmission error !!!!  MINTSTS: [0x00000088]
[ 0.994886] [mmc0] host was already tuning, Don't need to retry tune again ignore 0.
[ 0.994915] dwmmc_rockchip ff0f0000.rksdmmc: Tuning error: cmd.error:0, data.error:-84
[ 0.995204] dwmmc_rockchip ff0f0000.rksdmmc: Good phase range 0-169 (16 len)
[ 0.995216] dwmmc_rockchip ff0f0000.rksdmmc: Good phase range 192-282 (9 len)
[ 0.995227] dwmmc_rockchip ff0f0000.rksdmmc: Best phase range 0-169 (16 len)
[ 0.995237] dwmmc_rockchip ff0f0000.rksdmmc: Successfully tuned phase to 90
[ 0.995280] mmc0: new HS200 MMC card at address 0001
[ 0.995571] mmcblk0: mmc0:0001 AGND3R 14.5 GiB
[ 0.995877]  parameter: 0x000000000 -- 0x000400000 (4 MB)
[ 0.995888]    uboot: 0x000400000 -- 0x000800000 (4 MB)
[ 0.995896]    misc: 0x000800000 -- 0x000c00000 (4 MB)
[ 0.995905] resource: 0x000c00000 -- 0x001c00000 (16 MB)
[ 0.995914]    kernel: 0x001c00000 -- 0x002c00000 (16 MB)
[ 0.995922]    boot: 0x002c00000 -- 0x004c00000 (32 MB)
[ 0.995931] recovery: 0x004c00000 -- 0x006c00000 (32 MB)
[ 0.995939]    backup: 0x006c00000 -- 0x00a000000 (52 MB)
[ 0.995948]    cache: 0x00a000000 -- 0x012000000 (128 MB)
[ 0.995956]    kpanic: 0x012000000 -- 0x012400000 (4 MB)
[ 0.995965]    system: 0x012400000 -- 0x072400000 (1536 MB)
[ 0.995973] metadata: 0x072400000 -- 0x073400000 (16 MB)
[ 0.995981] baseparamer: 0x073400000 -- 0x073800000 (4 MB)
[ 0.995990] userdata: 0x073800000 -- 0x0b3800000 (1024 MB)
[ 0.995998] radical_update: 0x0b3800000 -- 0x0b7800000 (64 MB)
[ 0.996007]    user: 0x0b7800000 -- 0x3a3a00000 (11970 MB)
[ 0.996033]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16[ 0.997411] dwmmc_rockchip ff0c0000.rksdmmc: DW MMC controller at irq 64, 32 bit host data width, 256 deep fifo
[ 0.997424] dwmmc_rockchip ff0c0000.rksdmmc: 1 slots initialized
rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out 800000Hz for init[mmc1]
[ 0.997748] dw cru_regsbase addr 0x1d8.
[ 0.997756] dw cru_reset_offset val 1.
[ 0.997766] dwmmc_rockchip ff0d0000.rksdmmc: Version ID is 270a
[ 0.997800] dwmmc_rockchip ff0d0000.rksdmmc: failed to get hpclk_mmc
[ 0.998034] dwmmc_rockchip ff0d0000.rksdmmc: Using internal DMA controller.
[ 0.998167] dw_mci_init_slot: fmin=200000, fmax=50000000 [mmc2]
[ 0.998440] 1358..dw_mci_set_ios:  no card. [mmc2]
[ 1.017047] 1358..dw_mci_set_ios:  no card. [mmc2]
[ 1.036771] dwmmc_rockchip ff0d0000.rksdmmc: DW MMC controller at irq 65, 32 bit host data width, 256 deep fifo
[ 1.036785] dwmmc_rockchip ff0d0000.rksdmmc: 1 slots initialized
[ 1.037103] leds-gpio leds.34: pins are not configured from the driver
[ 1.037331] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.038771] usbcore: registered new interface driver usbhid
[ 1.038781] usbhid: USB HID core driver
[ 1.038895] ashmem: initialized
[ 1.039012] logger: created 256K log 'log_main'
[ 1.039108] logger: created 256K log 'log_events'
[ 1.039196] logger: created 256K log 'log_radio'
[ 1.039290] logger: created 256K log 'log_system'
[ 1.040365] input: rk29-keypad as /devices/ff100000.adc/key.37/input/input1
[ 1.041264] rockchip-pinctrl ff770000.pinctrl: pin gpio6-8 already requested by ff890000.rockchip-i2s; cannot claim for 2-0010
[ 1.041281] rockchip-pinctrl ff770000.pinctrl: pin-200 (2-0010) status -22
[ 1.041293] rockchip-pinctrl ff770000.pinctrl: could not request pin 200 on device rockchip-pinctrl
[ 1.041305] ES8323 2-0010: Error applying setting, reverse things back
[ 1.057045] mmc1: Skipping voltage switch
[ 1.127904] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[ 1.127924] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out normal clock [mmc1]
[ 1.127971] rk_sdmmc: BOOT Bus speed=50000000Hz,Bus width=4bits.[mmc1]
[ 1.127984] mmc1: new high speed SDHC card at address e624
[ 1.128223] mmcblk1: mmc1:e624 SS08G 7.40 GiB
[ 1.129012] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.129022] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.129039] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.129077] need_retune:0,brq->retune_retry_done:0.
[ 1.129086] mmcblk1: error -5 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
[ 1.129097] mmcblk1: retrying using single block read
[ 1.129333] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.129340] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.129358] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.129383] need_retune:0,brq->retune_retry_done:0.
[ 1.129391] mmcblk1: error -5 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
[ 1.129402] end_request: I/O error, dev mmcblk1, sector 0
[ 1.129551] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.129558] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.129574] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.129598] need_retune:0,brq->retune_retry_done:0.
[ 1.129607] mmcblk1: error -5 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
[ 1.129615] end_request: I/O error, dev mmcblk1, sector 1
[ 1.129763] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.129770] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.129784] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.129808] need_retune:0,brq->retune_retry_done:0.
[ 1.129816] mmcblk1: error -5 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
[ 1.129824] end_request: I/O error, dev mmcblk1, sector 2
[ 1.129972] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.129979] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.129995] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.130020] need_retune:0,brq->retune_retry_done:0.
[ 1.130028] mmcblk1: error -5 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
[ 1.130036] end_request: I/O error, dev mmcblk1, sector 3
[ 1.130185] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.130192] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.130207] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.130231] need_retune:0,brq->retune_retry_done:0.
[ 1.130239] mmcblk1: error -5 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
[ 1.130247] end_request: I/O error, dev mmcblk1, sector 4
[ 1.130395] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.130402] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.130416] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.130448] need_retune:0,brq->retune_retry_done:0.
[ 1.130456] mmcblk1: error -5 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
[ 1.130465] end_request: I/O error, dev mmcblk1, sector 5
[ 1.130613] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.130620] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.130636] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.130660] need_retune:0,brq->retune_retry_done:0.
[ 1.130667] mmcblk1: error -5 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
[ 1.130675] end_request: I/O error, dev mmcblk1, sector 6
[ 1.130823] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.130830] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.130845] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.130869] need_retune:0,brq->retune_retry_done:0.
[ 1.130877] mmcblk1: error -5 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
[ 1.130885] end_request: I/O error, dev mmcblk1, sector 7
[ 1.130894] Buffer I/O error on device mmcblk1, logical block 0
[ 1.131163] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.131170] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.131186] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.131211] need_retune:0,brq->retune_retry_done:0.
[ 1.131220] mmcblk1: error -5 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
[ 1.131228] mmcblk1: retrying using single block read
[ 1.131485] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.131492] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.131508] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.131531] need_retune:0,brq->retune_retry_done:0.
[ 1.131541] mmcblk1: error -5 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
[ 1.131554] end_request: I/O error, dev mmcblk1, sector 0
[ 1.131703] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.131710] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.131725] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.131749] need_retune:0,brq->retune_retry_done:0.
[ 1.131757] mmcblk1: error -5 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
[ 1.131766] end_request: I/O error, dev mmcblk1, sector 1
[ 1.131914] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.131922] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.131936] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.131960] need_retune:0,brq->retune_retry_done:0.
[ 1.131968] mmcblk1: error -5 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
[ 1.132117] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.132124] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.132140] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.132163] need_retune:0,brq->retune_retry_done:0.
[ 1.132172] mmcblk1: error -5 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
[ 1.132322] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.132329] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.132344] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.132367] need_retune:0,brq->retune_retry_done:0.
[ 1.132375] mmcblk1: error -5 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
[ 1.132525] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.132531] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.132547] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.132570] need_retune:0,brq->retune_retry_done:0.
[ 1.132578] mmcblk1: error -5 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
[ 1.132728] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.132735] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.132750] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.132773] need_retune:0,brq->retune_retry_done:0.
[ 1.132782] mmcblk1: error -5 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
[ 1.132931] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.132938] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.132952] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.132976] need_retune:0,brq->retune_retry_done:0.
[ 1.132984] mmcblk1: error -5 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
[ 1.132994] Buffer I/O error on device mmcblk1, logical block 0
[ 1.133258] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.133266] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.133282] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.133307] need_retune:0,brq->retune_retry_done:0.
[ 1.133315] mmcblk1: error -5 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
[ 1.133324] mmcblk1: retrying using single block read
[ 1.133581] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.133588] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.133603] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.133626] need_retune:0,brq->retune_retry_done:0.
[ 1.133634] mmcblk1: error -5 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
[ 1.133785] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.133792] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.133808] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.133835] need_retune:0,brq->retune_retry_done:0.
[ 1.133843] mmcblk1: error -5 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
[ 1.133993] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.134000] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.134015] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.134039] need_retune:0,brq->retune_retry_done:0.
[ 1.134046] mmcblk1: error -5 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
[ 1.134196] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.134203] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.134218] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.134241] need_retune:0,brq->retune_retry_done:0.
[ 1.134249] mmcblk1: error -5 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
[ 1.134399] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.134406] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.134421] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.134445] need_retune:0,brq->retune_retry_done:0.
[ 1.134453] mmcblk1: error -5 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
[ 1.134602] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.134609] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.134624] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.134648] need_retune:0,brq->retune_retry_done:0.
[ 1.134656] mmcblk1: error -5 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
[ 1.134806] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.134813] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.134829] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.134854] need_retune:0,brq->retune_retry_done:0.
[ 1.134861] mmcblk1: error -5 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
[ 1.135011] [mmc1] Data transmission error !!!!  MINTSTS: [0x00002000]
[ 1.135018] [mmc1] host was already tuning, Don't need to retry tune again ignore 0.
[ 1.135033] dwmmc_rockchip ff0c0000.rksdmmc: data FIFO error (status=00002000)
[ 1.135057] need_retune:0,brq->retune_retry_done:0.
[ 1.135065] mmcblk1: error -5 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
[ 1.135074] Buffer I/O error on device mmcblk1, logical block 0
[ 1.135092]  mmcblk1: unable to read partition table
[ 1.135284] 1358..dw_mci_set_ios:  no card. [mmc2]
[ 1.233521] rockchip_i2c ff660000.i2c: i2c is not in idle(state = 3)
[ 1.233530] es8323 probe error
[ 1.233546] ES8323: probe of 2-0010 failed with error -5
[ 1.234334] rockchip-spdif ff880000.rockchip-spdif: spdif ready.
[ 1.234740] rockchip-es8323 rockchip-es8323.32: ASoC: CODEC (null) not registered
[ 1.234765] rockchip_es8323_audio_probe() register card failed:-517
[ 1.234777] platform rockchip-es8323.32: Driver rockchip-es8323 requests probe deferral
[ 1.234918] u32 classifier
[ 1.234924]    Actions configured
[ 1.234935] Netfilter messages via NETLINK v0.30.
[ 1.234987] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 1.235257] ctnetlink v0.93: registering with nfnetlink.
[ 1.235320] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 1.235326] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 1.235584] xt_time: kernel timezone is -0000
[ 1.235746] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.235854] arp_tables: (C) 2002 David S. Miller
[ 1.235887] TCP: cubic registered
[ 1.235892] Initializing XFRM netlink socket
[ 1.236054] NET: Registered protocol family 10
[ 1.236491] mip6: Mobile IPv6
[ 1.236526] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 1.236626] sit: IPv6 over IPv4 tunneling driver
[ 1.236886] NET: Registered protocol family 17
[ 1.236907] NET: Registered protocol family 15
[ 1.236951] Bridge firewalling registered
[ 1.236961] Ebtables v2.0 registered
[ 1.237099] Bluetooth: RFCOMM TTY layer initialized
[ 1.237119] Bluetooth: RFCOMM socket layer initialized
[ 1.237127] Bluetooth: RFCOMM ver 1.11
[ 1.237133] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 1.237138] Bluetooth: BNEP filters: protocol multicast
[ 1.237146] Bluetooth: BNEP socket layer initialized
[ 1.237152] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 1.237161] Bluetooth: HIDP socket layer initialized
[ 1.237183] l2tp_core: L2TP core driver, V2.0
[ 1.237194] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 1.237200] [WLAN_RFKILL]: Enter rfkill_wlan_init
[ 1.237389] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[ 1.237398] [WLAN_RFKILL]: can't find rockchip,grf property
[ 1.237405] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = bcmwifi
[ 1.237412] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[ 1.237419] [WLAN_RFKILL]: wlan_platdata_parse_dt: disable wifi io reference voltage control.
[ 1.237426] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[ 1.237448] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,poweren_gpio = 156, flags = 0.
[ 1.237464] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 158, flags = 0.
[ 1.237471] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[ 1.237496] [WLAN_RFKILL]: rockchip_wifi_voltage_select: wifi & sdio reference voltage: 1.8V
[ 1.237503] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[ 1.237541] [BT_RFKILL]: Enter rfkill_rk_init
[ 1.237669] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 147.
[ 1.237683] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,power_gpio = 155.
[ 1.237694] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 157.
[ 1.237706] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 154.
[ 1.237717] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 159.
[ 1.237754] [BT_RFKILL]: Request irq for bt wakeup host
[ 1.237845] [BT_RFKILL]: ** disable irq
[ 1.237924] [BT_RFKILL]: ap6335 device registered.
[ 1.238529] rk3288_init_suspend
[ 1.238541] rk3288_suspend_init enter
[ 1.238742] rk3288_suspend_init: pm_ctrbits =200007
[ 1.238769] gpio_get_dts_info suspend:4
[ 1.238775] gpio_get_dts_info resume:4
[ 1.238780] rockchip,pmic-suspend_gpios:14007a10 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
[ 1.238802] rockchip,pmic-resume_gpios:2007a11 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
[ 1.238917] clks_gating_suspend_init:clkgt info ok
[ 1.238999] Registering SWP/SWPB emulation handler
[ 1.239010] rockchip_uboot_mem_late_init: Freeing uboot logo memory: 0x02000000@0x7dc00000
[ 1.240911] DVFS ERR: clk_enable_dvfs: vd(vd_logic) can't get regulator(vdd_logic)!
[ 1.241325] ddrfreq: verion 1.2 20140526
[ 1.241337] ddrfreq: normal 456MHz video_1080p 0MHz video_4k 456MHz dualview 0MHz idle 0MHz suspend 200MHz reboot 456MHz
[ 1.241345] ddrfreq: auto-freq=0
[ 1.241349] ddrfreq: auto-freq-table[0] 240MHz
[ 1.241354] ddrfreq: auto-freq-table[1] 324MHz
[ 1.241359] ddrfreq: auto-freq-table[2] 456MHz
[ 1.241364] ddrfreq: auto-freq-table[3] 528MHz
[ 1.241882] Unable to handle kernel paging request at virtual address fffffe2b
[ 1.489604] rockchip_i2c ff650000.i2c: Addr[0x0040] wait event timeout, state: 1, is_busy: 1, error: 0, complete_what: 0x0, ipd: 0x10
[ 1.491637] rockchip_i2c ff650000.i2c: I2C_CON: start bit is set
[ 1.686419] rockchip_i2c ff650000.i2c: Addr[0x0040] wait event timeout, state: 1, is_busy: 1, error: 0, complete_what: 0x0, ipd: 0x10
[ 1.688450] rockchip_i2c ff650000.i2c: I2C_CON: start bit is set
[ 1.883224] rockchip_i2c ff650000.i2c: Addr[0x0040] wait event timeout, state: 1, is_busy: 1, error: 0, complete_what: 0x0, ipd: 0x10
[ 1.885251] rockchip_i2c ff650000.i2c: I2C_CON: start bit is set
[ 1.886289] ###################WARNING:set voltage is error!voltage set is 900000 mv -110
[ 1.886333] DVFS ERR: dvfs_regulator_set_voltage_readback: now read back to check voltage
[ 2.080027] rockchip_i2c ff650000.i2c: Addr[0x0040] wait event timeout, state: 1, is_busy: 1, error: 0, complete_what: 0x0, ipd: 0x10
[ 2.082053] rockchip_i2c ff650000.i2c: I2C_CON: start bit is set
[ 2.083092] DVFS ERR: dvfs_regulator_set_voltage_readback: set ERROR AND NOT effected, volt=937500
[ 2.083143] DVFS ERR: dvfs_scale_volt_direct: vd_arm set voltage up err ret = -110, Vnew = 900000(was 1350000)mV
[ 2.316248] saradc-reg[0x00-0x0c]: 0x000003fb 0x00000000 0x00000069 0x00000008
[ 2.316303] read channel() error: -110
[ 3.398615] saradc-reg[0x00-0x0c]: 0x000003fa 0x00000000 0x00000069 0x00000008
[ 3.398671] read channel() error: -110
[ 4.480957] saradc-reg[0x00-0x0c]: 0x000003fb 0x00000000 0x00000069 0x00000008
[ 4.481013] read channel() error: -110
[ 5.563299] saradc-reg[0x00-0x0c]: 0x000003fb 0x00000000 0x00000069 0x00000008
[ 5.563354] read channel() error: -110
[ 5.929000] DVFS WARNING: dvfs_reset_volt:vd(vd_arm) try to reload volt = 1350000
[ 5.929080] pgd = c0004000
[ 5.929151] [fffffe2b] *pgd=1eff6821, *pte=00000000, *ppte=00000000
[ 5.929209] Internal error: Oops: 17 [#1] PREEMPT SMP ARM
[ 5.929253] Modules linked in:
[ 5.929313] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.0 #23
[ 5.929361] task: de890000 ti: de872000 task.ti: de872000
[ 5.929440] PC is at regulator_set_voltage+0x8/0xe0
[ 5.929501] LR is at vga_edid_probe+0x4c/0x380
[ 5.929556] pc : [<c02ed35c>] lr : [<c02e2450>] psr: a0000113
[ 5.929556] sp : de873e38  ip : 00000000  fp : 00000000
[ 5.929612] r10: c0bb35f0  r9 : c0c46478  r8 : c02e2404
[ 5.929654] r7 : c1f4a7d4  r6 : debf9c00  r5 : 00000000  r4 : fffffdfb
[ 5.929698] r3 : 00000000  r2 : 001b7740  r1 : 001b7740  r0 : fffffdfb
[ 5.929746] Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
[ 5.929790] Control: 10c5387d  Table: 0000406a  DAC: 00000015
[ 5.929824]
[ 5.929824] PC: 0xc02ed2dc:
[ 5.929930] d2dc  e3530000 1a000002 e5962018 e3520000 0a000013 e58d3000 e1a00004 e5963018
[ 5.930021] d2fc  e1a0100d e28d2004 e58d3004 ebfffa2a e2506000 ba00000b e1a00004 e1a0100d
[ 5.930109] d31c  e28d2004 ebffffb9 e2506000 ba000005 e1a00004 e89d0006 ebfffc02 e1a06000
[ 5.930196] d33c  ea000000 e3e06015 e1a00005 eb15b4fc e1a00006 e8bd807c e92d45f7 e1a04000
[ 5.930283] d35c  e5905030 e58d2000 e2856038 e58d1004 e1a00006 eb15b589 e5942014 e59d3004
[ 5.930371] d37c  e1520003 1a000004 e5942018 e59d3000 e1520003 03a0a000 0a000022 e5953000
[ 5.930458] d39c  e5933014 e5932004 e3520000 1a000003 e593300c e3530000 03e0a015 0a000019
[ 5.930545] d3bc  e1a00005 e28d1004 e1a0200d ebfff9fa e250a000 ba000013 e59d3004 e1a00005
[ 5.930576]
[ 5.930576] LR: 0xc02e23d0:
[ 5.930678] 23d0  e1a01005 e1a03000 e3a00004 ebf5b782 ea000001 e59f0014 eb15748c e1a00004
[ 5.930766] 23f0  e8bd81f0 c0eb9fac c02e2814 c004f88c c0a8e198 e92d41ff e1a06000 e590715c
[ 5.930854] 2410  e5900018 e5903008 e5933008 e12fff33 e3100001 03e05012 0a0000b0 e3a00000
[ 5.930942] 2430  e59f12c4 eb002a07 e2504000 059f02bc 0a000007 e59f12b8 e1a02001 eb002bc0
[ 5.931028] 2450  e1a00004 eb002cbb e3500000 159f02a4 059f02a4 e59f12a4 eb15746c e3a00000
[ 5.931116] 2470  e59f129c eb0029f7 e2504000 059f0294 0a000007 e59f1290 e1a02001 eb002bb0
[ 5.931202] 2490  e1a00004 eb002cab e3500000 159f027c 059f027c e59f1264 eb15745c e3a00000
[ 5.931290] 24b0  e59f1270 eb0029e7 e2504000 059f0268 0a000007 e59f1264 e1a02001 eb002ba0
[ 5.931320]
[ 5.931320] SP: 0xde873db8:
[ 5.931418] 3db8  c0284f84 c0ec1c4c 00000000 00000001 c0ec1c64 00000000 000003e0 00000000
[ 5.931506] 3dd8  00000020 c02ed35c a0000113 ffffffff de873e24 c000d598 fffffdfb 001b7740
[ 5.931593] 3df8  001b7740 00000000 fffffdfb 00000000 debf9c00 c1f4a7d4 c02e2404 c0c46478
[ 5.931677] 3e18  c0bb35f0 00000000 00000000 de873e38 c02e2450 c02ed35c a0000113 ffffffff
[ 5.931764] 3e38  fffffdfb 001b7740 001b7740 fffffdfb 00000000 debf9c00 c1f4a7d4 c02e2404
[ 5.931847] 3e58  c0bb35f0 c02e2450 debf9c00 00000000 00000065 00000000 debf9c20 00000000
[ 5.931932] 3e78  debf9c04 debf9c00 c02e2404 c0527a48 00000000 debf9c20 00000000 c0c89fb0
[ 5.932018] 3e98  c0ddf000 c030b1c0 debf9c20 c0c89fb0 c0c89fb0 00000000 c0ddf000 c030b41c
[ 5.932048]
[ 5.932048] R0: 0xfffffd7b:
[ 5.932163] fd78  ******** ******** ******** ******** ******** ******** ******** ********
[ 5.932255] fd98  ******** ******** ******** ******** ******** ******** ******** ********
[ 5.932343] fdb8  ******** ******** ******** ******** ******** ******** ******** ********
[ 5.932432] fdd8  ******** ******** ******** ******** ******** ******** ******** ********
[ 5.932520] fdf8  ******** ******** ******** ******** ******** ******** ******** ********
[ 5.932608] fe18  ******** ******** ******** ******** ******** ******** ******** ********
[ 5.932694] fe38  ******** ******** ******** ******** ******** ******** ******** ********
[ 5.932782] fe58  ******** ******** ******** ******** ******** ******** ******** ********
[ 5.932869] fe78  ******** ******** ******** ******** ******** ******** ******** ********
[ 5.932899]
[ 5.932899] R4: 0xfffffd7b:
[ 5.933003] fd78  ******** ******** ******** ******** ******** ******** ******** ********
[ 5.933090] fd98  ******** ******** ******** ******** ******** ******** ******** ********
[ 5.933177] fdb8  ******** ******** ******** ******** ******** ******** ******** ********
[ 5.933264] fdd8  ******** ******** ******** ******** ******** ******** ******** ********
[ 5.933351] fdf8  ******** ******** ******** ******** ******** ******** ******** ********
[ 5.933438] fe18  ******** ******** ******** ******** ******** ******** ******** ********
[ 5.933525] fe38  ******** ******** ******** ******** ******** ******** ******** ********
[ 5.933612] fe58  ******** ******** ******** ******** ******** ******** ******** ********
[ 5.933699] fe78  ******** ******** ******** ******** ******** ******** ******** ********
[ 5.933728]
[ 5.933728] R6: 0xdebf9b80:
[ 5.933820] 9b80  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 5.933898] 9ba0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 5.933976] 9bc0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 5.934053] 9be0  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 5.934138] 9c00  00500000 5f616776 00636464 00000000 00000000 00000000 debf2058 c0c89f8c
[ 5.934224] 9c20  debf2080 debba900 debbeb80 c0db5a5c debf9a2c debf2088 de9810c0 c0d0ea28
[ 5.934305] 9c40  debbeb40 00000003 00000007 00000000 c0d65ccc 00000000 00000000 debf9c5c
[ 5.934388] 9c60  debf9c5c de890000 00000000 c0d65d14 c0c89fb0 00000000 00000000 00000020
[ 5.934418]
[ 5.934418] R7: 0xc1f4a754:
[ 5.934513] a754  00000000 00000000 c5618401 00000004 c561393c c1f4a790 00000000 00000000
[ 5.934596] a774  c5618401 00000124 00000004 00000000 c05fce58 00000000 00000000 c0ae5c3c
[ 5.934677] a794  0000000d c1f4a7c4 00000000 00000000 00000000 c0ae5c3c 00000124 0000000d
[ 5.934759] a7b4  00000000 c05fce58 00000000 00000000 30316b72 635f3030 6365646f 00000000
[ 5.934843] a7d4  c1f4a9b4 c0af203e 00000000 c1f4a82c c1f4a848 00000000 c1f49cfc 00000000
[ 5.934928] a7f4  00000000 00000000 c1f4a9bc dea78f00 c1f4a9ec c1f4a5dc c1f49d28 dea1a600
[ 5.935010] a814  c0db584c dea78f80 00000001 00000003 00000008 00000000 6332692f 31666640
[ 5.935096] a834  30303036 67762f30 64645f61 30354063 00000000 c56182e7 00000010 c5613960
[ 5.935125]
[ 5.935125] R8: 0xc02e2384:
[ 5.935225] 2384  e3a02000 e5843004 e2840010 e5843008 e3a01002 e59f3058 e584300c e1a03002
[ 5.935311] 23a4  ebf587f0 e59f304c e5844024 e1a00008 e584504c e5843020 e5847050 e5846054
[ 5.935398] 23c4  e5955030 ebf56ab4 e1a02004 e1a01005 e1a03000 e3a00004 ebf5b782 ea000001
[ 5.935484] 23e4  e59f0014 eb15748c e1a00004 e8bd81f0 c0eb9fac c02e2814 c004f88c c0a8e198
[ 5.935570] 2404  e92d41ff e1a06000 e590715c e5900018 e5903008 e5933008 e12fff33 e3100001
[ 5.935657] 2424  03e05012 0a0000b0 e3a00000 e59f12c4 eb002a07 e2504000 059f02bc 0a000007
[ 5.935744] 2444  e59f12b8 e1a02001 eb002bc0 e1a00004 eb002cbb e3500000 159f02a4 059f02a4
[ 5.935831] 2464  e59f12a4 eb15746c e3a00000 e59f129c eb0029f7 e2504000 059f0294 0a000007
[ 5.935860]
[ 5.935860] R9: 0xc0c463f8:
[ 5.935960] 63f8  c0bdf8a4 c0bdf8b4 c0bdf8c4 c0bdf8d4 c0bdf8e4 c0bdf8f4 c0bdf904 c0bdf914
[ 5.936046] 6418  c0bdf924 c0bdf934 c0bdf944 c0bdf954 c0bdf964 c0bb5764 c0bb6ee0 c0bba2ac
[ 5.936133] 6438  c0bba498 c0029178 c0bbc7d4 c0036718 c0bbcfe0 c0bbf0d4 c0bc0710 c0bc0770
[ 5.936219] 6458  c0bc0894 c0bc08f8 c0bc29d8 c0bc4d5c c0bc8884 c0bd86b8 c0bd90cc c0bd9724
[ 5.936305] 6478  c0bd995c c030af44 c03ae0c4 c042c0b0 c045f088 c0bde598 c0bdea98 c0bdeb44
[ 5.936407] 6498  c0be35f4 c0be37f4 c0be54d8 c0be6d34 c0bea074 c0bea0f8 c0bec7e0 c060e5fc
[ 5.936494] 64b8  c0be62cc c0be6d58 c0be6fd8 c0bd4b88 37303730 30303130 32303030 30303144
[ 5.936581] 64d8  31343030 30304445 30303030 30303030 30303030 30303030 30303030 38353230
[ 5.936610]
[ 5.936610] R10: 0xc0bb3570:
[ 5.936712] 3570  e5941000 ebd2838a e3500000 1a000009 e1a00005 e59f1058 ebdb359d e3500000
[ 5.936798] 3590  1a00000c e5940000 e59f1048 ebdb3598 e3500000 1a000007 e5943004 e1a00007
[ 5.936885] 35b0  e12fff33 e3500000 0a000002 e59f0028 e1a01005 ebf23015 e284400c e1540006
[ 5.936971] 35d0  3affffe2 e3a00000 e8bd80f8 c0c45160 c0c45670 c0a567e0 c0a56663 c0a5666c
[ 5.937057] 35f0  e92d4038 e2515000 e1a04000 0a000014 ebdb35bc e2803001 e0843003 e1550003
[ 5.937144] 3610  03a0303d 05453001 0a00000d e2800002 e0844000 e1550004 1a000008 e3a0303d
[ 5.937231] 3630  e1a00005 e5453002 ebdb35ae e1a01005 e2802001 e2450001 ebdb1490 ea000000
[ 5.937316] 3650  e7f001f2 e3a00000 e8bd8038 e92d45f8 e1a04000 e1a06001 ebffffe0 e1a00004
[ 5.937359] Process swapper/0 (pid: 1, stack limit = 0xde872238)
[ 5.937397] Stack: (0xde873e38 to 0xde874000)
[ 5.937443] 3e20:                                                    fffffdfb 001b7740
[ 5.937511] 3e40: 001b7740 fffffdfb 00000000 debf9c00 c1f4a7d4 c02e2404 c0bb35f0 c02e2450
[ 5.937573] 3e60: debf9c00 00000000 00000065 00000000 debf9c20 00000000 debf9c04 debf9c00
[ 5.937636] 3e80: c02e2404 c0527a48 00000000 debf9c20 00000000 c0c89fb0 c0ddf000 c030b1c0
[ 5.937698] 3ea0: debf9c20 c0c89fb0 c0c89fb0 00000000 c0ddf000 c030b41c 00000000 debf9c20
[ 5.937762] 3ec0: debf9c54 c030b494 c0c89fb0 de873ed8 c030b434 c0309c5c de9d875c debba934
[ 5.937825] 3ee0: c0c89fb0 c0c89fb0 c582f800 c0d65d14 00000000 c030aa10 c0a8e322 c0a8e323
[ 5.937888] 3f00: c0c89fb0 c0bd9724 de872000 00000000 c0ddf000 c030b980 c0d65d14 c0c89f8c
[ 5.937949] 3f20: c0bd9724 de872000 00000000 c0ddf000 c0bb35f0 c0529784 00000000 00000007
[ 5.938011] 3f40: c0bd9724 c00086a4 c0bd9724 00000004 00000007 c0c00cbc c0c00c9c c0ddf000
[ 5.938072] 3f60: 000001fd c0bb3b28 00000007 00000007 c0bb35f0 00000000 c0c456bc c0c456bc
[ 5.938130] 3f80: 00000000 00000000 00000000 00000000 00000000 c0bb3be8 de872000 00000000
[ 5.938189] 3fa0: c083921c c0839224 00000000 c000da98 00000000 00000000 00000000 00000000
[ 5.938244] 3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 5.938303] 3fe0: 00000000 00000000 00000000 00000000 00000013 00000000 ffffffff ffffffff
[ 5.938431] [<c02ed35c>] (regulator_set_voltage+0x8/0xe0) from [<c02e2450>] (vga_edid_probe+0x4c/0x380)
[ 5.938542] [<c02e2450>] (vga_edid_probe+0x4c/0x380) from [<c0527a48>] (i2c_device_probe+0xa8/0xd4)
[ 5.938647] [<c0527a48>] (i2c_device_probe+0xa8/0xd4) from [<c030b1c0>] (really_probe+0xa8/0x20c)
[ 5.938743] [<c030b1c0>] (really_probe+0xa8/0x20c) from [<c030b41c>] (driver_probe_device+0x30/0x48)
[ 5.938834] [<c030b41c>] (driver_probe_device+0x30/0x48) from [<c030b494>] (__driver_attach+0x60/0x84)
[ 5.938922] [<c030b494>] (__driver_attach+0x60/0x84) from [<c0309c5c>] (bus_for_each_dev+0x50/0x90)
[ 5.939007] [<c0309c5c>] (bus_for_each_dev+0x50/0x90) from [<c030aa10>] (bus_add_driver+0xac/0x20c)
[ 5.939095] [<c030aa10>] (bus_add_driver+0xac/0x20c) from [<c030b980>] (driver_register+0x9c/0x138)
[ 5.939170] [<c030b980>] (driver_register+0x9c/0x138) from [<c0529784>] (i2c_register_driver+0x40/0xac)
[ 5.939252] [<c0529784>] (i2c_register_driver+0x40/0xac) from [<c00086a4>] (do_one_initcall+0x34/0xc8)
[ 5.939341] [<c00086a4>] (do_one_initcall+0x34/0xc8) from [<c0bb3b28>] (do_initcalls+0x70/0xa0)
[ 5.939424] [<c0bb3b28>] (do_initcalls+0x70/0xa0) from [<c0bb3be8>] (kernel_init_freeable+0x90/0x130)
[ 5.939511] [<c0bb3be8>] (kernel_init_freeable+0x90/0x130) from [<c0839224>] (kernel_init+0x8/0xe4)
[ 5.939597] [<c0839224>] (kernel_init+0x8/0xe4) from [<c000da98>] (ret_from_fork+0x14/0x3c)
[ 5.939660] Code: e1a00006 e8bd807c e92d45f7 e1a04000 (e5905030)
[ 5.940100] EHCI: rk_ehci_hcd_enable, disable host controller
[ 5.940256] ---[ end trace a3421f486481674a ]---
[ 5.940392] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[ 5.940392]
[ 5.940466] CPU1: stopping
[ 5.940532] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G    D    3.10.0 #23
[ 5.940652] [<c0013ec4>] (unwind_backtrace+0x0/0xe0) from [<c001176c>] (show_stack+0x10/0x14)
[ 5.940740] [<c001176c>] (show_stack+0x10/0x14) from [<c0012f9c>] (handle_IPI+0x154/0x2c8)
[ 5.940817] [<c0012f9c>] (handle_IPI+0x154/0x2c8) from [<c0008558>] (gic_handle_irq+0x54/0x5c)
[ 5.940893] [<c0008558>] (gic_handle_irq+0x54/0x5c) from [<c000d600>] (__irq_svc+0x40/0x70)
[ 5.940933] Exception stack(0xde8bdf30 to 0xde8bdf78)
[ 5.940985] df20:                                  de8bdf78 00000005 52c2fb57 00000001
[ 5.941052] df40: c1f652e0 00000000 52c16c94 00000001 c0c5f018 de8bc000 c0c5f028 00000000
[ 5.941110] df60: 00000000 de8bdf78 c0079850 c05b7e6c 60000113 ffffffff
[ 5.941196] [<c000d600>] (__irq_svc+0x40/0x70) from [<c05b7e6c>] (cpuidle_enter_state+0x54/0xec)
[ 5.941276] [<c05b7e6c>] (cpuidle_enter_state+0x54/0xec) from [<c05b8070>] (cpuidle_idle_call+0x16c/0x27c)
[ 5.941356] [<c05b8070>] (cpuidle_idle_call+0x16c/0x27c) from [<c000e750>] (arch_cpu_idle+0x8/0x38)
[ 5.941444] [<c000e750>] (arch_cpu_idle+0x8/0x38) from [<c0078c14>] (cpu_idle_loop+0x1b8/0x224)
[ 5.941524] [<c0078c14>] (cpu_idle_loop+0x1b8/0x224) from [<c0078c8c>] (freezing_slow_path+0x0/0x80)
[ 5.941570] CPU3: stopping
[ 5.941637] CPU: 3 PID: 0 Comm: swapper/3 Tainted: G    D    3.10.0 #23
[ 5.941748] [<c0013ec4>] (unwind_backtrace+0x0/0xe0) from [<c001176c>] (show_stack+0x10/0x14)
[ 5.941832] [<c001176c>] (show_stack+0x10/0x14) from [<c0012f9c>] (handle_IPI+0x154/0x2c8)
[ 5.941909] [<c0012f9c>] (handle_IPI+0x154/0x2c8) from [<c0008558>] (gic_handle_irq+0x54/0x5c)
[ 5.941985] [<c0008558>] (gic_handle_irq+0x54/0x5c) from [<c000d600>] (__irq_svc+0x40/0x70)
[ 5.942024] Exception stack(0xde8c1f30 to 0xde8c1f78)
[ 5.942077] 1f20:                                  de8c1f78 00000005 52c2fb57 00000001
[ 5.942145] 1f40: c1f772e0 00000000 52c0358b 00000001 c0c5f018 de8c0000 c0c5f028 00000000
[ 5.942201] 1f60: 00000000 de8c1f78 c0079850 c05b7e6c 60000113 ffffffff
[ 5.942283] [<c000d600>] (__irq_svc+0x40/0x70) from [<c05b7e6c>] (cpuidle_enter_state+0x54/0xec)
[ 5.942360] [<c05b7e6c>] (cpuidle_enter_state+0x54/0xec) from [<c05b8070>] (cpuidle_idle_call+0x16c/0x27c)
[ 5.942440] [<c05b8070>] (cpuidle_idle_call+0x16c/0x27c) from [<c000e750>] (arch_cpu_idle+0x8/0x38)
[ 5.942523] [<c000e750>] (arch_cpu_idle+0x8/0x38) from [<c0078c14>] (cpu_idle_loop+0x1b8/0x224)
[ 5.942601] [<c0078c14>] (cpu_idle_loop+0x1b8/0x224) from [<c0078c8c>] (freezing_slow_path+0x0/0x80)
[ 7.223647] CPU2: stopping
[ 7.226311] CPU: 2 PID: 72 Comm: cfinteractive Tainted: G    D    3.10.0 #23
[ 7.233605] [<c0013ec4>] (unwind_backtrace+0x0/0xe0) from [<c001176c>] (show_stack+0x10/0x14)
[ 7.241991] [<c001176c>] (show_stack+0x10/0x14) from [<c0012f9c>] (handle_IPI+0x154/0x2c8)
[ 7.250113] [<c0012f9c>] (handle_IPI+0x154/0x2c8) from [<c0008558>] (gic_handle_irq+0x54/0x5c)
[ 7.258576] [<c0008558>] (gic_handle_irq+0x54/0x5c) from [<c000d600>] (__irq_svc+0x40/0x70)
[ 7.266747] Exception stack(0xddd99de0 to 0xddd99e28)
[ 7.271721] 9de0: c0dfefc8 60000193 00000000 00000000 00000045 00000006 c0dffd12 00000004
[ 7.279747] 9e00: 00000000 00000000 60000113 00000002 00000000 ddd99e28 c0038ce0 c0038ce4
[ 7.287739] 9e20: 60000113 ffffffff
[ 7.291203] [<c000d600>] (__irq_svc+0x40/0x70) from [<c0038ce4>] (vprintk_emit+0x3f0/0x444)
[ 7.299425] [<c0038ce4>] (vprintk_emit+0x3f0/0x444) from [<c083f64c>] (printk+0x2c/0x3c)
[ 7.307398] [<c083f64c>] (printk+0x2c/0x3c) from [<c002c028>] (dvfs_reset_volt+0x68/0x94)
[ 7.315450] [<c002c028>] (dvfs_reset_volt+0x68/0x94) from [<c002cbcc>] (dvfs_target+0x40/0x1fc)
[ 7.324011] [<c002cbcc>] (dvfs_target+0x40/0x1fc) from [<c002b34c>] (dvfs_clk_set_rate+0x44/0x80)
[ 7.332737] [<c002b34c>] (dvfs_clk_set_rate+0x44/0x80) from [<c05b7714>] (cpufreq_target+0x108/0x134)
[ 7.341801] [<c05b7714>] (cpufreq_target+0x108/0x134) from [<c05af52c>] (__cpufreq_driver_target+0x5c/0x70)
[ 7.351390] [<c05af52c>] (__cpufreq_driver_target+0x5c/0x70) from [<c05b3d7c>] (cpufreq_interactive_speedchange_task+0x12c/0x210)
[ 7.362863] [<c05b3d7c>] (cpufreq_interactive_speedchange_task+0x12c/0x210) from [<c0056110>] (kthread+0xa0/0xac)
[ 7.372960] [<c0056110>] (kthread+0xa0/0xac) from [<c000da98>] (ret_from_fork+0x14/0x3c)
[ 7.380875] CRU:
[ 7.382714] 00000000: 00000107 9fff0053 0fff002a 00000008 00000005 9fff0031 0fff0018 00000008
[ 7.391096] 00000020: 00000203 9fff0103 0fff0082 00000008 00000007 9fff00c5 0fff0014 00000008
[ 7.399470] 00000040: 00000b00 1fff0270 0fff0138 0000000a 00001111 00000000 00000000 00000000
[ 7.407843] 00000060: 00004031 0000b108 00000003 00000200 00008100 00008100 00008585 00010014
[ 7.416215] 00000080: 01885091 01885091 0000a101 00002745 00004345 00008a00 00000200 00000200
[ 7.424588] 000000a0: 00000200 0bb8ea60 00010014 00010014 00010014 00000910 00000900 001f05dc
[ 7.432959] 000000c0: 00001703 0000078c 00000e40 00000300 00000542 00000302 00004141 00000000
[ 7.441330] 000000e0: 00004141 00000505 00008042 00008f8f 00000000 00000631 00001ee5 00008307
[ 7.449698] 00000100: 00001200 00010014 00004141 00000000 00000000 00000000 00000000 00000000
[ 7.458063] 00000120: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.466420] 00000140: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.474781] 00000160: 00000000 00000000 00000100 00000800 00000000 00000000 0000eb00 00000092
[ 7.483147] 00000180: 00000000 00000000 0000000c 00000000 00000000 0000e010 00000000 00000000
[ 7.491503] 000001a0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.499861] 000001c0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.508220] 000001e0: 00000000 00000000 00000000 00640064 00000004 00000000 00000000 00000000
[ 7.516586] 00000200: 00000002 00000000 00000002 00000000 00000002 00000000 00000004 000004e0
[ 7.524952] 00000220: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.533309] 00000240: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.541666] 00000260: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.550032] 00000280: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.558399] 000002a0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.566757] 000002c0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.575114] 000002e0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.583471] 00000300: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.591837] 00000320: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.600195] 00000340: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.608552] 00000360: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.616909] 00000380: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.625267] 000003a0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.633624] 000003c0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.641982] 000003e0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.650346] 00000400: 00000107 9fff0053 0fff002a 00000008 00000005 9fff0031 0fff0018 00000008
[ 7.658688] Rebooting in 5 seconds..

作者: jpchen 时间: 2016-11-28 09:01

werren 发表于 2016-11-27 01:01
Android 4.4上面问题好像更严重……
串口信息如下：

你烧公版的固件试试，如果还是有问题，可能是板子坏了

作者: werren 时间: 2016-11-29 01:05

jpchen 发表于 2016-11-28 09:01
你烧公版的固件试试，如果还是有问题，可能是板子坏了

下载官方的img发现还是一样的现象，跑到开机log数据跑到第六秒左右，又重启。
我手上有一块rk3288-reload，下载可以正常work。
可是板子寄给我的时候有测试过点屏的，是好的。

无标题.png (19.41 KB, 下载次数: 482)

作者: werren 时间: 2016-11-29 01:19

jpchen 发表于 2016-11-28 09:01
你烧公版的固件试试，如果还是有问题，可能是板子坏了

有时候擦除flash重新烧录后会有画面，如图。
擦除flash，烧录后不断电一直是：启动--开机logo--6秒后重启--开机logo 循环
但是如果断电重启，就不会有开机logo，串口看开机logo可以知道一直在重启。

632008567851692136 - 副本.jpg (335.18 KB, 下载次数: 526)

作者: jpchen 时间: 2016-11-29 15:49

werren 发表于 2016-11-29 01:19
有时候擦除flash重新烧录后会有画面，如图。
擦除flash，烧录后不断电一直是：启动--开机logo--6秒后重 ...

你们是哪公司自己弄的板子

作者: werren 时间: 2016-11-30 10:23

jpchen 发表于 2016-11-29 15:49
你们是哪公司自己弄的板子

X3288CV核心板。
我试了下4.4的，可以跑，还有一些问题待解救

欢迎光临 Firefly开源社区 (https://dev.t-firefly.com/)