Firefly开源社区

标题: log报错： DMA mask not set [打印本页]

作者: 513453733 时间: 2022-4-25 20:05
标题: log报错： DMA mask not set

问题：DMA mask not set

网上也没找到相关的解决方法，小白求助。

核心板：core-3568j
行业版：aio-3568j
所驱动芯片：瑞芯微rk628d

dts代码如下：其中部分代码参考子rk官方提供的节点配置以及安卓内核中部分其他主板的rk628驱动dts
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (c) 2020 Rockchip Electronics Co., Ltd.
*
*/

#include "rk3568-firefly-aioj.dtsi"
/*
*                            Select one of the three
* using single camera xc7160 ----> rk3568-firefly-aioj-cam-8ms1m.dtsi
* using dual camera gc2053/gc2093 ----> rk3568-firefly-aioj-cam-2ms2m.dtsi
* using hdmi-in module rk628d ----> rk3568-firefly-aioj-tf-hdmi-mipi-rk628.dtsi
*/
#include "rk3568-firefly-aioj-cam-8ms1m.dtsi"
//#include "rk3568-firefly-aioj-cam-2ms2m.dtsi"
//#include "rk3568-firefly-aioj-tf-hdmi-mipi-rk628.dtsi"

/ {
model = "AIO-3568J HDMI (Android)";
compatible = "rockchip,rk3568-firefly-aioj", "rockchip,rk3568";

};

&route_hdmi {
status = "okay";
connect = <&vp0_out_hdmi>;
};

&i2c4{
clock-frequency = <400000>;
status = "okay";

rk628: rk628@50{
      reg = <0x50>;
      interrupt-parent = <&gpio3>;
      interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;

      reset-gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_LOW>;
      status = "okay";

};
};

#include <arm/rk628.dtsi>

&rk628_combtxphy{
status = "okay";
};

&rk628_combrxphy{
status = "okay";
};

&rk628_csi {
status = "okay";
/** If the hpd output level is inverted on the circuit, * the following configuration needs to be enabled. */
/* hpd-output-inverted; */
plugin-det-gpios = <&gpio0 RK_PD6 GPIO_ACTIVE_HIGH>; //
//power-gpios = <&gpio0 17 GPIO_ACTIVE_HIGH>;
rockchip,camera-module-index = <0>;
rockchip,camera-module-facing = "back";
rockchip,camera-module-name = "RK628-CSI";
rockchip,camera-module-lens-name = "NC";

port {
      hdmiin_out0: endpoint {
         remote-endpoint = <&mipi_in>;
         data-lanes = <1 2 3 4>;
      };
};
};

&csi2_dphy_hw {
status = "okay";
};

&csi2_dphy0 {
status = "okay";

ports {
      #address-cells = <1>;
      #size-cells = <0>;
      port@0 {
         reg = <0>;
         #address-cells = <1>;
         #size-cells = <0>;

         mipi_in: endpoint@0 {
            reg = <0>;
            remote-endpoint = <&hdmiin_out0>;
            data-lanes = <1 2 3 4>;
         };
      };

      port@1 {
         reg = <1>;
         #address-cells = <1>;
         #size-cells = <0>;

         csidphy0_out: endpoint@0 {
            reg = <0>;
            remote-endpoint = <&isp0_in>;
         };
      };
};
};

&rkisp {
status = "okay";
};

&rkisp_mmu {
status = "okay";
};

&rkisp_vir0 {
status = "okay";

port {
      #address-cells = <1>;
      #size-cells = <0>;

      isp0_in: endpoint@0 {
         reg = <0>;
         remote-endpoint = <&csidphy0_out>;
      };
};
};

tchip_askquestions

SH7PZ1W`_P83GW2$1WK3]GN.jpg (246.28 KB, 下载次数: 1157)

log.zip

27.99 KB, 下载次数: 0, 下载积分: 灯泡 -1 , 经验 -1

作者: 513453733 时间: 2022-4-26 11:38

好像是这个的问题，有人知道这个是怎么回事码

作者: zyk 时间: 2022-4-26 14:30
配置的引脚是否被复用或其它模块申请了？

作者: 513453733 时间: 2022-4-26 14:52

zyk 发表于 2022-4-26 14:30
配置的引脚是否被复用或其它模块申请了？

确实，问题已经解决了，应该是i2c先挂在了其他模块了

欢迎光临 Firefly开源社区 (https://dev.t-firefly.com/)