Firefly开源社区

标题: 3588J Android12 怎么单独更新内核？ [打印本页]

作者: Zsasz 时间: 2022-8-11 16:51
标题: 3588J Android12 怎么单独更新内核？
我用 msk ARCH=arm64 BOOT_IMG=../rockdev/Image-rk3588_firefly_itx_3588j/boot.img rk3588-firefly-itx-3588j.img -j8 命令编译的boot.img
用  sudo ../RKTools/linux/Linux_Upgrade_Tool/Linux_Upgrade_Tool_v2.4/upgrade_tool di -b boot.img 命令烧录的内核
发现修改的打印都没有变化，所以请问要怎么才能更新内核？

kernel前开机打印如下：
DDR Version V1.07 20220412
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL board init
U-Boot SPL 2017.09-gc060f28d70-220414 #zyf (Apr 18 2022 - 18:13:34)
Failed to set cpub01
Failed to set cpub23
unknown raw ID phN
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
MMC: no card present
mmc_init: -123, time 1
spl: mmc init failed with error: -123
Trying to boot from MMC1
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(581130cddd...) + OK
## Checking uboot 0x00200000 ... sha256(48b3755843...) + OK
## Checking fdt 0x00328498 ... sha256(c07f4a4d71...) + OK
## Checking atf-2 0x000f0000 ... sha256(6a00298af8...) + OK
## Checking atf-3 0xff100000 ... sha256(71c3a5841b...) + OK
## Checking atf-4 0xff001000 ... sha256(2301cf73be...) + OK
## Checking optee 0x08400000 ... sha256(603cfbd25d...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 116.2 ms

INFO: Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-364-g55ca4fb1c:derrick.huang
NOTICE:  BL31: Built : 12:00:02, May 13 2022
INFO: timer_hp_init no valid 32k timer source, use normal mode
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: system boots from cpu-hwid-0
INFO: idle_st=0x21fff, pd_st=0x11fff9
INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO: BL31: Initialising Exception Handling Framework
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
INFO: hdmirx_handler: dma not on, ret
I/TC:
I/TC: OP-TEE version: 3.13.0-639-g8e053a881-dev #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #2 Mon Mar 14 09:09:01 CST 2022 aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9

U-Boot 2017.09 (Aug 11 2022 - 15:34:50 +0800)

Model: Rockchip RK3588 Evaluation Board
PreSerial: 2, raw, 0xfeb50000
DRAM:  7.7 GiB
Sysmem: init
Relocation Offset: edb4e000
Relocation fdt: eb9fa168 - eb9fecd0
CR: M/C/I
Using default environment

mmc@fe2c0000: 1, mmc@fe2e0000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
DM: v2
boot mode: None
Android 12.0, Build 2022.4, v2
Found DTB in boot part
DTB: rk-kernel.dtb
HASH(c): OK
ANDROID: fdt overlay OK
I2c0 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big0_s0 1000000 uV
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big1_s0 675000 uV
I2c1 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_npu_s0 812500 uV
spi2: RK806: 2
ON=0x00, OFF=0x00
vdd_gpu_s0 750000 uV
vdd_cpu_lit_s0 750000 uV
vdd_log_s0 750000 uV
vdd_vdenc_s0 init 750000 uV
vdd_ddr_s0 850000 uV
I2c6 speed: 400000Hz
Error reading output register
Error reading output register
Error reading output register
Error reading output register
Error reading output register
Error reading output register
Error reading output register
Error reading output register
Model: Firefly ITX-3588J HDMI(Android)
CLK: (uboot. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A)
  b0pll 1200000 KHz
  b1pll 1200000 KHz
  lpll 1200000 KHz
  v0pll 24000 KHz
  aupll 786431 KHz
  cpll 1500000 KHz
  gpll 1188000 KHz
  npll 850000 KHz
  ppll 1100000 KHz
  aclk_center_root 702000 KHz
  pclk_center_root 100000 KHz
  hclk_center_root 396000 KHz
  aclk_center_low_root 500000 KHz
  aclk_top_root 750000 KHz
  pclk_top_root 100000 KHz
  aclk_low_top_root 396000 KHz
Net: eth1: ethernet@fe1c0000, eth0: ethernet@fe1b0000
Hit key to stop autoboot('CTRL+C'):  0
ANDROID: reboot reason: "recovery"
optee api revision: 2.0
Vboot=0, AVB images, AVB verify
read_is_device_unlocked() ops returned that device is UNLOCKED
avb_footer.c:41: ERROR: Footer magic is incorrect.
avb_vbmeta_image.c:65: ERROR: Magic is incorrect.
avb_slot_verify.c:773: ERROR: recovery: Error verifying vbmeta image: invalid vbmeta header
Verify recovery with vbmeta.
avb_slot_verify.c:762: ERROR: vbmeta: Error verifying vbmeta image: OK_NOT_SIGNED
get image from preloaded partition...
ANDROID: Hash OK
Could not find "system" partition
Booting IMAGE kernel at 0x00400000 with fdt at 0x0a100000...

Fdt Ramdisk skip relocation
## Booting Android Image at 0x003ff800 ...
Kernel: 0x00400000 - 0x026e6008 (35737 KiB)
ramdisk: 0x0a200000 - 0x0d05f2f2 (47485 KiB)
## Flattened Device Tree blob at 0x0a100000
Booting using the fdt blob at 0x0a100000
XIP Kernel Image from 0x00400000 to 0x00400000 ... OK
kernel loaded at 0x00400000, end = 0x026e6008
  'reserved-memory' cma: addr=10000000 size=10000000
Using Device Tree in place at 000000000a100000, end 000000000a140979
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x100000000 - 0x200000000 (size: 0x100000000)
Total: 2864.620 ms

Starting kernel ...

作者: Zsasz 时间: 2022-8-15 14:54
我编译安卓的时候用eng的flag编译出debug版本就可以正常替换内核了。。

作者: xyxyyxyx 时间: 2024-11-5 16:30

Zsasz 发表于 2022-8-15 14:54
我编译安卓的时候用eng的flag编译出debug版本就可以正常替换内核了。。

兄弟，你咋编译的，我和你遇到的情况一样

欢迎光临 Firefly开源社区 (https://dev.t-firefly.com/)