Firefly开源社区

标题: iCore-3568JQ最小系统有那些条件? [打印本页]

作者: hejh    时间: 2022-8-15 10:06
标题: iCore-3568JQ最小系统有那些条件?
iCore-3568JQ最小系统有那些条件?
我开机 后只有40-50ma是什么问题?
tchip_askquestions

文档.txt

3 Bytes, 下载次数: 1, 下载积分: 灯泡 -1 , 经验 -1


作者: zyk    时间: 2022-8-15 11:46
你好。最小系统,你指的是什么,硬件最小系统?还是指功耗方面的问题
作者: hejh    时间: 2022-8-15 13:30
硬件
作者: zyk    时间: 2022-8-15 14:13
硬件最小电路跟单片机最小电路差不多,时钟、电源(PMU)、复位、启动介质等电路;底板设计参考ITX-3568JQ
作者: hejh    时间: 2022-8-17 09:42
核心板说明上
1.   VCC5V0_SYS电源是核心板系统供电电源,电压范围4.8V-5.5V;核心板内部5V—>3.3V给PMIC供电。
2.  37:VD_IN脚是强制开机管脚,该管脚只要电压大于3V,核心板就会自动开机。如果不需要上电自动开机,该脚可以NC。
其它的时钟不在核心板上面吗?还有其它的条件吗?

作者: wx__X7oLde    时间: 2022-8-24 22:30
我自己做了个底板,只提供sys_5V电源,没有外设,开机后会无法启动。循环打log


[    1.496056] rockchip-usb2phy fe8a0000.usb2-phy: failed to create phy
[    1.496790] rockchip-usb2phy fe8b0000.usb2-phy: failed to create phy
[    1.498167] rockchip-drm display-subsystem: devfreq is ready
[    1.498546] vp0: rgb_pixelclk: 0
[    1.498588] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x15, primary plane phy id: 4
[    1.498605] vp1: rgb_pixelclk: 0
[    1.498620] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp1 assign plane mask: 0x22, primary plane phy id: 5
[    1.498632] vp2: rgb_pixelclk: 1
[    1.498642] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x8, primary plane phy id: 3
[    1.498940] [drm] failed to init overlay plane Cluster0-win1
[    1.498989] [drm] failed to init overlay plane Cluster1-win1
[    1.499169] rockchip-drm display-subsystem: bound fe040000.vop (ops 0xffffff8009032338)
[    1.501220] rockchip-drm display-subsystem: bound fe0c0000.edp (ops 0xffffff80090353e8)
[    1.501556] dwhdmi-rockchip fe0a0000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[    1.502506] dwhdmi-rockchip fe0a0000.hdmi: registered DesignWare HDMI I2C bus driver
[    1.504799] rockchip-drm display-subsystem: bound fe0a0000.hdmi (ops 0xffffff8009035e50)
[    1.504899] rockchip-rgb fdc60000.syscon:rgb: [drm:rockchip_rgb_bind] *ERROR* failed to find panel or bridge: -517
[    1.508223] /rgb0_panel: could not find display-timings node
[    1.508257] /rgb0_panel: no timings specified
[    1.508361] panel-simple rgb0_panel: rgb0_panel supply power not found, using dummy regulator
[    1.508495] panel-simple rgb0_panel: rgb0_panel supply vsp not found, using dummy regulator
[    1.508564] panel-simple rgb0_panel: rgb0_panel supply vsn not found, using dummy regulator
[    1.509448] dwc3 fcc00000.dwc3: Failed to get clk 'ref': -2
[    1.511032] dwc3 fd000000.dwc3: Failed to get clk 'ref': -2



[    1.517597] rockchip-usb2phy fe8a0000.usb2-phy: failed to create phy
[    1.518445] rockchip-usb2phy fe8b0000.usb2-phy: failed to create phy
[    1.519524] rockchip-drm display-subsystem: devfreq is ready
[    1.519890] vp0: rgb_pixelclk: 0
[    1.519931] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x15, primary plane phy id: 4
[    1.519952] vp1: rgb_pixelclk: 0
[    1.519964] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp1 assign plane mask: 0x22, primary plane phy id: 5
[    1.519979] vp2: rgb_pixelclk: 1
[    1.519991] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x8, primary plane phy id: 3
[    1.520338] [drm] failed to init overlay plane Cluster0-win1
[    1.520389] [drm] failed to init overlay plane Cluster1-win1
[    1.520580] rockchip-drm display-subsystem: bound fe040000.vop (ops 0xffffff8009032338)
[    1.522303] rockchip-drm display-subsystem: bound fe0c0000.edp (ops 0xffffff80090353e8)
[    1.522595] dwhdmi-rockchip fe0a0000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[    1.523454] dwhdmi-rockchip fe0a0000.hdmi: registered DesignWare HDMI I2C bus driver
[    1.525501] rockchip-drm display-subsystem: bound fe0a0000.hdmi (ops 0xffffff8009035e50)
[    1.525596] rockchip-rgb fdc60000.syscon:rgb: [drm:rockchip_rgb_bind] *ERROR* failed to find panel or bridge: -517
[    1.529013] /rgb0_panel: could not find display-timings node
[    1.529046] /rgb0_panel: no timings specified
[    1.529146] panel-simple rgb0_panel: rgb0_panel supply power not found, using dummy regulator
[    1.529278] panel-simple rgb0_panel: rgb0_panel supply vsp not found, using dummy regulator
[    1.529344] panel-simple rgb0_panel: rgb0_panel supply vsn not found, using dummy regulator
[    1.530345] dwc3 fcc00000.dwc3: Failed to get clk 'ref': -2
[    1.531781] dwc3 fd000000.dwc3: Failed to get clk 'ref': -2


[    1.538380] rockchip-usb2phy fe8a0000.usb2-phy: failed to create phy
[    1.539185] rockchip-usb2phy fe8b0000.usb2-phy: failed to create phy
[    1.540528] rockchip-drm display-subsystem: devfreq is ready
[    1.540936] vp0: rgb_pixelclk: 0
[    1.540977] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x15, primary plane phy id: 4
[    1.540993] vp1: rgb_pixelclk: 0
[    1.541006] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp1 assign plane mask: 0x22, primary plane phy id: 5
[    1.541021] vp2: rgb_pixelclk: 1
[    1.541033] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x8, primary plane phy id: 3
[    1.541157] mmc_host mmc3: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[    1.541736] [drm] failed to init overlay plane Cluster0-win1
[    1.541828] [drm] failed to init overlay plane Cluster1-win1
[    1.542064] rockchip-drm display-subsystem: bound fe040000.vop (ops 0xffffff8009032338)
[    1.542301] mmc3: new high speed SDIO card at address 0001
[    1.544281] rockchip-drm display-subsystem: bound fe0c0000.edp (ops 0xffffff80090353e8)
[    1.544581] dwhdmi-rockchip fe0a0000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[    1.545492] dwhdmi-rockchip fe0a0000.hdmi: registered DesignWare HDMI I2C bus driver
[    1.547517] rockchip-drm display-subsystem: bound fe0a0000.hdmi (ops 0xffffff8009035e50)
[    1.547606] rockchip-rgb fdc60000.syscon:rgb: [drm:rockchip_rgb_bind] *ERROR* failed to find panel or bridge: -517
[    1.550856] /rgb0_panel: could not find display-timings node
[    1.550894] /rgb0_panel: no timings specified
[    1.550988] panel-simple rgb0_panel: rgb0_panel supply power not found, using dummy regulator
[    1.551124] panel-simple rgb0_panel: rgb0_panel supply vsp not found, using dummy regulator
[    1.551191] panel-simple rgb0_panel: rgb0_panel supply vsn not found, using dummy regulator
[    1.551870] vendor storage:20190527 ret = 0
[    1.552156] dwc3 fcc00000.dwc3: Failed to get clk 'ref': -2
[    1.553379] dwc3 fd000000.dwc3: Failed to get clk 'ref': -2
作者: zyk    时间: 2022-8-25 10:29
wx__X7oLde 发表于 2022-8-24 22:30
我自己做了个底板,只提供sys_5V电源,没有外设,开机后会无法启动。循环打log

参考https://dev.t-firefly.com/thread-123990-1-5.html
作者: hejh    时间: 2022-9-1 15:30
wx__X7oLde 发表于 2022-8-24 22:30
我自己做了个底板,只提供sys_5V电源,没有外设,开机后会无法启动。循环打log

你的问题找解决了吗?




欢迎光临 Firefly开源社区 (https://dev.t-firefly.com/) Powered by Discuz! X3.1