Firefly开源社区

标题: RK3568 烧录/启动失败 [打印本页]

作者: run 时间: 2022-8-27 15:02
标题: RK3568 烧录/启动失败

RK3568 烧录/启动失败

RK3568烧录镜像后,无法正常启动, 通过debug串口看到如下打印信息, 按照论坛教程操作下载minloaderall.bin, 选择将存储切换到emmc, 但在选择list storage按钮时,报错, 不知啥原因? 不知是不是emmc坏掉了

一, 启动失败, 串口打印内容

二, 按照论坛教程擦除NOR flash

三下载minloaderall.bin, 点Download , 下载成功

四点List Storage按钮

失败, 弹窗: “Reading storage list failed”

串口打印内容如下:

tchip_askquestions

新建文本文档 (3).txt

3.62 KB, 下载次数: 0, 下载积分: 灯泡 -1 , 经验 -1

作者: zyk 时间: 2022-8-28 00:08
好像没有看见Miniloaderall.bin下载成功的log，是否点击了Download再点击list storage。可以尝试用firefly提供的方法烧写https://wiki.t-firefly.com/Core- ... #fang-fa-yi-firefly

作者: run 时间: 2022-8-28 10:04

zyk 发表于 2022-8-28 00:08
好像没有看见Miniloaderall.bin下载成功的log，是否点击了Download再点击list storage。可以尝试用firefly ...

这是下载MInloaderall.bin的日志,下载成功

DDR Version V1.09 20210630
In
ddrconfig:7
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=4096MB
tdqss: cs0 dqs0: -24ps, dqs1: -120ps, dqs2: -72ps, dqs3: -168ps,
tdqss: cs1 dqs0: -24ps, dqs1: -120ps, dqs2: -48ps, dqs3: -168ps,

change to: 324MHz
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:41%
dram drv:40,odt:0
clk skew:0x63

change to: 528MHz
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58

change to: 780MHz
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58

change to: 1560MHz(final freq)
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:22%
dram drv:40,odt:80
vref_ca:00000071
clk skew:0x30
cs 0:
the read training result:
DQS0:0x39, DQS1:0x36, DQS2:0x3c, DQS3:0x31,
min  :0x11 0x14 0x13 0x11  0x2  0x4  0x8  0x2 , 0xc  0xa  0x4  0x1  0xb  0x7  0xb  0x4 ,
   0x17 0x17 0x11  0xe  0x6  0x2  0x4  0x6 , 0xd  0x9  0x6  0x3  0xc  0xe  0xa  0xb ,
mid  :0x2d 0x31 0x2e 0x2d 0x1e 0x20 0x23 0x1f ,0x27 0x27 0x1e 0x1e 0x27 0x23 0x25 0x21 ,
   0x32 0x33 0x2b 0x2a 0x21 0x1e 0x1f 0x21 ,0x27 0x23 0x20 0x1d 0x26 0x27 0x24 0x26 ,
max  :0x4a 0x4e 0x4a 0x4a 0x3a 0x3c 0x3f 0x3c ,0x42 0x44 0x38 0x3c 0x44 0x3f 0x3f 0x3e ,
   0x4d 0x4f 0x46 0x46 0x3d 0x3a 0x3a 0x3c ,0x42 0x3d 0x3a 0x37 0x41 0x41 0x3e 0x41 ,
range:0x39 0x3a 0x37 0x39 0x38 0x38 0x37 0x3a ,0x36 0x3a 0x34 0x3b 0x39 0x38 0x34 0x3a ,
   0x36 0x38 0x35 0x38 0x37 0x38 0x36 0x36 ,0x35 0x34 0x34 0x34 0x35 0x33 0x34 0x36 ,
the write training result:
DQS0:0x2c, DQS1:0x19, DQS2:0x22, DQS3:0xf,
min  :0x68 0x6b 0x6b 0x6a 0x5b 0x5d 0x60 0x5f 0x5d ,0x4e 0x4c 0x45 0x48 0x50 0x4f 0x4c 0x4e 0x4a ,
   0x60 0x60 0x58 0x59 0x4e 0x4e 0x4d 0x53 0x51 ,0x48 0x46 0x3f 0x3d 0x4a 0x4a 0x48 0x4d 0x43 ,
mid  :0x81 0x84 0x83 0x82 0x73 0x76 0x79 0x77 0x76 ,0x69 0x68 0x5f 0x61 0x6c 0x6a 0x68 0x68 0x63 ,
   0x7b 0x7a 0x71 0x74 0x68 0x67 0x67 0x6c 0x6b ,0x62 0x5f 0x59 0x58 0x64 0x64 0x61 0x68 0x5b ,
max  :0x9a 0x9e 0x9b 0x9a 0x8b 0x90 0x93 0x90 0x8f ,0x85 0x84 0x7a 0x7a 0x88 0x85 0x85 0x82 0x7d ,
   0x96 0x94 0x8a 0x8f 0x83 0x81 0x82 0x86 0x86 ,0x7d 0x78 0x74 0x74 0x7e 0x7f 0x7a 0x83 0x73 ,
range:0x32 0x33 0x30 0x30 0x30 0x33 0x33 0x31 0x32 ,0x37 0x38 0x35 0x32 0x38 0x36 0x39 0x34 0x33 ,
   0x36 0x34 0x32 0x36 0x35 0x33 0x35 0x33 0x35 ,0x35 0x32 0x35 0x37 0x34 0x35 0x32 0x36 0x30 ,
cs 1:
the read training result:
DQS0:0x39, DQS1:0x35, DQS2:0x3d, DQS3:0x31,
min  :0x12 0x14 0x14 0x10  0x2  0x7  0x8  0x4 , 0xa  0xa  0x2  0x1  0xc  0x8  0x8  0x4 ,
   0x17 0x17 0x11  0xe  0x6  0x2  0x6  0x7 , 0xc  0x9  0x5  0x1  0xc  0xc  0x9  0xa ,
mid  :0x2d 0x2f 0x2f 0x2c 0x1e 0x21 0x23 0x1f ,0x26 0x26 0x1c 0x1e 0x27 0x23 0x23 0x1f ,
   0x33 0x34 0x2c 0x2a 0x21 0x1f 0x21 0x22 ,0x26 0x23 0x1f 0x1b 0x26 0x26 0x23 0x25 ,
max  :0x49 0x4b 0x4b 0x49 0x3a 0x3c 0x3f 0x3b ,0x42 0x42 0x36 0x3b 0x43 0x3f 0x3e 0x3b ,
   0x4f 0x52 0x48 0x47 0x3d 0x3c 0x3c 0x3e ,0x41 0x3d 0x3a 0x36 0x41 0x41 0x3e 0x40 ,
range:0x37 0x37 0x37 0x39 0x38 0x35 0x37 0x37 ,0x38 0x38 0x34 0x3a 0x37 0x37 0x36 0x37 ,
   0x38 0x3b 0x37 0x39 0x37 0x3a 0x36 0x37 ,0x35 0x34 0x35 0x35 0x35 0x35 0x35 0x36 ,
the write training result:
DQS0:0x2c, DQS1:0x19, DQS2:0x22, DQS3:0xf,
min  :0x66 0x6a 0x69 0x68 0x58 0x5a 0x5d 0x5f 0x5d ,0x4c 0x4c 0x45 0x47 0x4e 0x4c 0x4c 0x4d 0x48 ,
   0x60 0x62 0x5b 0x5c 0x51 0x4f 0x4f 0x53 0x53 ,0x48 0x46 0x3d 0x3d 0x48 0x4a 0x48 0x4a 0x42 ,
mid  :0x80 0x84 0x82 0x81 0x71 0x74 0x78 0x77 0x76 ,0x66 0x65 0x5d 0x5f 0x68 0x66 0x66 0x65 0x62 ,
   0x7d 0x7d 0x75 0x77 0x6c 0x6a 0x6b 0x6e 0x6e ,0x62 0x5f 0x58 0x57 0x63 0x65 0x60 0x64 0x5b ,
max  :0x9a 0x9f 0x9c 0x9b 0x8b 0x8f 0x93 0x90 0x8f ,0x81 0x7f 0x76 0x78 0x83 0x80 0x80 0x7d 0x7d ,
   0x9a 0x98 0x8f 0x92 0x87 0x85 0x87 0x8a 0x89 ,0x7c 0x78 0x74 0x72 0x7e 0x81 0x78 0x7e 0x74 ,
range:0x34 0x35 0x33 0x33 0x33 0x35 0x36 0x31 0x32 ,0x35 0x33 0x31 0x31 0x35 0x34 0x34 0x30 0x35 ,
   0x3a 0x36 0x34 0x36 0x36 0x36 0x38 0x37 0x36 ,0x34 0x32 0x37 0x35 0x36 0x37 0x30 0x34 0x32 ,
CA Training result:
cs:0 min  :0x5d 0x4f 0x4f 0x40 0x4e 0x3e 0x52 ,0x5b 0x4a 0x4d 0x40 0x4b 0x41 0x55 ,
cs:0 mid  :0x93 0x93 0x87 0x83 0x86 0x82 0x7c ,0x93 0x8f 0x86 0x82 0x83 0x85 0x7e ,
cs:0 max  :0xc9 0xd7 0xbf 0xc7 0xbe 0xc7 0xa7 ,0xcb 0xd4 0xbf 0xc5 0xbc 0xc9 0xa8 ,
cs:0 range:0x6c 0x88 0x70 0x87 0x70 0x89 0x55 ,0x70 0x8a 0x72 0x85 0x71 0x88 0x53 ,
cs:1 min  :0x5c 0x55 0x4e 0x45 0x4f 0x44 0x55 ,0x58 0x50 0x4b 0x44 0x4b 0x43 0x54 ,
cs:1 mid  :0x96 0x95 0x87 0x85 0x88 0x82 0x80 ,0x94 0x8d 0x86 0x83 0x86 0x84 0x7e ,
cs:1 max  :0xd0 0xd6 0xc1 0xc5 0xc1 0xc0 0xab ,0xd0 0xcb 0xc1 0xc2 0xc1 0xc6 0xa9 ,
cs:1 range:0x74 0x81 0x73 0x80 0x72 0x7c 0x56 ,0x78 0x7b 0x76 0x7e 0x76 0x83 0x55 ,
out
Boot1 Release Time: Jun 18 2021 20:07:33, version: 1.10
support nand flash type: slc
...nandc_flash_init enter...
No.1 FLASH ID:ff ff ff ff ff ff
sfc nor id: ef 60 19
UsbBoot ...4540
powerOn 4756

作者: run 时间: 2022-8-28 10:08

run 发表于 2022-8-28 10:04
这是下载MInloaderall.bin的日志,下载成功

DDR Version V1.09 20210630

这是下载Minloaderall.bin成功后,再点击list storage的日志,  弹窗报错Reading storage  list  failed!

...nandc_flash_init enter...
No.1 FLASH ID:ff ff ff ff ff ff
sfc_nand id: 60 19 0
SD IO init 0
Set SD Clk: 200, 5
Set SD Clk: 200, 5
SDC_BusRequest:  CMD=8  SDC_RESP_TIMEOUT 1747
mmc0:cmd8,20
SDC_BusRequest:  CMD=5  SDC_RESP_TIMEOUT 1747
mmc0:cmd5,20
SDC_BusRequest:  CMD=55  SDC_RESP_TIMEOUT 1747
mmc0:cmd55,20
SDC_BusRequest:  CMD=1  SDC_RESP_TIMEOUT 1747
mmc0:cmd1,20
Set SD Clk: 200, 5
SDC_BusRequest:  CMD=8  SDC_RESP_TIMEOUT 1747
mmc0:cmd8,20
SDC_BusRequest:  CMD=5  SDC_RESP_TIMEOUT 1747
mmc0:cmd5,20
SDC_BusRequest:  CMD=55  SDC_RESP_TIMEOUT 1747
mmc0:cmd55,20
SDC_BusRequest:  CMD=1  SDC_RESP_TIMEOUT 1747
mmc0:cmd1,20
Set SD Clk: 200, 5
SDC_BusRequest:  CMD=8  SDC_RESP_TIMEOUT 1747
mmc0:cmd8,20
SDC_BusRequest:  CMD=5  SDC_RESP_TIMEOUT 1747
mmc0:cmd5,20
SDC_BusRequest:  CMD=55  SDC_RESP_TIMEOUT 1747
mmc0:cmd55,20
SDC_BusRequest:  CMD=1  SDC_RESP_TIMEOUT 1747
mmc0:cmd1,20
SdmmcInit=0 1
Emmc IO init.
EMMC_DLL_RXCLK = 20000000
Emmc IO init.
EMMC_DLL_RXCLK = 20000000
mmc_set_bus_width: 1
SetEmmcClk: 375000, 5
SetEmmcClk: 25000000, 0
mmc_set_bus_width: 8
cid 000000000331d0e0 + 0x0:0x9b010059,0x32503033,0x32000aec,0x98624800,

version 000000000331d1ee + 0x0:0x0c,0x06,0x00,0x00,0x00,0x00,0x00,0x00,
write: 000000000331d500 + 0x0:0x00,0xff,0xff,0xff,0x00,0xff,0xff,0xff,0x00,0xff,0xff,0xff,0x00,0xff,0xff,0xff,

mmc write ret = 10
mmc read ret = 8
read1 : 000000000331d700 + 0x0:0x00,0xff,0xff,0xff,0x00,0xff,0xff,0xff,0x00,0xff,0xff,0xff,0x00,0xff,0xff,0xff,

SetEmmcClk: 375000, 5
0, low  : fe9fffff
0, high : febfffff
1, low  : fe9fffff
1, high : febfffff
2, low  : fe900fff
2, high : febfffff
3, low  : fe9fffff
3, high : feb00fff
4, low  : fe9fffff
4, high : febfffff
5, low  : fe9fffff
5, high : febfffff
6, low  : fe900fff
6, high : febfffff
7, low  : fe9fffff
7, high : feb00fff
8, low  : fe9fffff
8, high : febfffff
9, low  : fe9fffff
9, high : febfffff
10, low  : fe900fff
10, high : febfffff
11, low  : fe9fffff
11, high : feb00fff
12, low  : fe9fffff
12, high : febfffff
13, low  : fe9fffff
13, high : febfffff
14, low  : fe900fff
14, high : febfffff
15, low  : fe9fffff
15, high : feb00fff
ret 0
mmc_set_bus_width: 1
SetEmmcClk: 375000, 5
mmc_set_bus_width: 8
SetEmmcClk: 200000000, 1
Enable PHY CLK: 200000000
mmc: ERROR: SDHCI:Timeout for status update! cmd:0x153a, stat:0x0, mask:0x20
mmc: ERROR: sdhci_send_tuning failed -19
mmc: ERROR: tuning execution failed
emmc reinit
mmc_set_bus_width: 1
SetEmmcClk: 375000, 5
mmc: ERROR: SDHCI:Timeout for status update! cmd:0x0, stat:0x0, mask:0x1
mmc: ERROR: SDHCI:Timeout for status update! cmd:0x0, stat:0x20, mask:0x1
SetEmmcClk: 25000000, 0
mmc_set_bus_width: 8
cid 000000000331d0e0 + 0x0:0x9b010059,0x32503033,0x32000aec,0x98624800,

version 000000000331d1ee + 0x0:0x0c,0x06,0x00,0x00,0x00,0x00,0x00,0x00,
write: 000000000331d500 + 0x0:0x00,0xff,0xff,0xff,0x00,0xff,0xff,0xff,0x00,0xff,0xff,0xff,0x00,0xff,0xff,0xff,

mmc write ret = 10
mmc read ret = 8
read1 : 000000000331d700 + 0x0:0x00,0xff,0xff,0xff,0x00,0xff,0xff,0xff,0x00,0xff,0xff,0xff,0x00,0xff,0xff,0xff,

SetEmmcClk: 375000, 5
0, low  : fe900fff
0, high : febfffff
1, low  : fe9fffff
1, high : feb00fff
2, low  : fe9fffff
2, high : febfffff
3, low  : fe9fffff
3, high : febfffff
4, low  : fe900fff
4, high : febfffff
5, low  : fe9fffff
5, high : feb00fff
6, low  : fe9fffff
6, high : febfffff
7, low  : fe9fffff
7, high : febfffff
8, low  : fe900fff
8, high : febfffff
9, low  : fe9fffff
9, high : feb00fff
10, low  : fe9fffff
10, high : febfffff
11, low  : fe9fffff
11, high : febfffff
12, low  : fe900fff
12, high : febfffff
13, low  : fe9fffff
13, high : feb00fff
14, low  : fe9fffff
14, high : febfffff
15, low  : fe9fffff
15, high : febfffff
ret 0
mmc_set_bus_width: 1
mmc_set_bus_width: 8
SetEmmcClk: 200000000, 1
Enable PHY CLK: 200000000
mmc: ERROR: SDHCI:Timeout for status update! cmd:0x153a, stat:0x0, mask:0x20
mmc: ERROR: sdhci_send_tuning failed -19
mmc: ERROR: tuning execution failed
emmc reinit
mmc_set_bus_width: 1
SetEmmcClk: 375000, 5
mmc: ERROR: SDHCI:Timeout for status update! cmd:0x0, stat:0x0, mask:0x1
mmc: ERROR: SDHCI:Timeout for status update! cmd:0x0, stat:0x20, mask:0x1
SetEmmcClk: 25000000, 0
mmc_set_bus_width: 8
cid 000000000331d0e0 + 0x0:0x9b010059,0x32503033,0x32000aec,0x98624800,

version 000000000331d1ee + 0x0:0x0c,0x06,0x00,0x00,0x00,0x00,0x00,0x00,
write: 000000000331d500 + 0x0:0x00,0xff,0xff,0xff,0x00,0xff,0xff,0xff,0x00,0xff,0xff,0xff,0x00,0xff,0xff,0xff,

mmc write ret = 10
mmc read ret = 8
read1 : 000000000331d700 + 0x0:0x00,0xff,0xff,0xff,0x00,0xff,0xff,0xff,0x00,0xff,0xff,0xff,0x00,0xff,0xff,0xff,

SetEmmcClk: 375000, 5
0, low  : fe900fff
0, high : febfffff
1, low  : fe9fffff
1, high : feb00fff
2, low  : fe9fffff
2, high : febfffff
3, low  : fe9fffff
3, high : febfffff
4, low  : fe900fff
4, high : febfffff
5, low  : fe9fffff
5, high : feb00fff
6, low  : fe9fffff
6, high : febfffff
7, low  : fe9fffff
7, high : febfffff
8, low  : fe900fff
8, high : febfffff
9, low  : fe9fffff
9, high : feb00fff
10, low  : fe9fffff
10, high : febfffff
11, low  : fe9fffff
11, high : febfffff
12, low  : fe900fff
12, high : febfffff
13, low  : fe9fffff
13, high : feb00fff
14, low  : fe9fffff
14, high : febfffff
15, low  : fe9fffff
15, high : febfffff
ret 0
mmc_set_bus_width: 1
mmc_set_bus_width: 8
SetEmmcClk: 200000000, 1
Enable PHY CLK: 200000000
mmc: ERROR: SDHCI:Timeout for status update! cmd:0x153a, stat:0x0, mask:0x20
mmc: ERROR: sdhci_send_tuning failed -19
mmc: ERROR: tuning execution failed
SdmmcInit=2 1

作者: run 时间: 2022-8-28 10:11

zyk 发表于 2022-8-28 00:08
好像没有看见Miniloaderall.bin下载成功的log，是否点击了Download再点击list storage。可以尝试用firefly ...

作者: zyk 时间: 2022-8-29 09:38
1.可以参考wiki用RK356x_NorFlash2eMMC-Loader_xxx.img小固件看看能否进入eMMC的loader模式
2.可以短接Nor flash，直接烧写固件、
3.可以通过制作SD升级卡的方式烧写固件

如果都不行，联系一下售后处理

作者: run 时间: 2022-8-29 17:43

zyk 发表于 2022-8-29 09:38
1.可以参考wiki用RK356x_NorFlash2eMMC-Loader_xxx.img小固件看看能否进入eMMC的loader模式
2.可以短接Nor ...

1.RK356x_NorFlash2eMMC-Loader_xxx.img小固件可以进入eMMC的loader模式,也可以下载程序, 但无法启动, 一直报 config file not found no ethernet found
2. 如何短接Nor flash 了??????????????????????
3. SD卡验证过不行, 请问怎么短接nor flash了

作者: zyk 时间: 2022-8-29 17:54
可以贴一下完整的log。短接参考示意图，短接D0和GND

作者: run 时间: 2022-8-29 21:58

zyk 发表于 2022-8-29 17:54
可以贴一下完整的log。短接参考示意图，短接D0和GND

刚试了下, 短接无任何反应,没有进入 MaskRom 模式

作者: zyk 时间: 2022-8-30 09:25
联系售后处理一下吧

欢迎光临 Firefly开源社区 (https://dev.t-firefly.com/)