Firefly开源社区

标题: missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm [打印本页]

作者: 13761765359 时间: 2023-6-27 17:36
标题: missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm
核心板运行一段时间后，不能正常启动，日志如下，烦请各位大佬指点，出现此情况的原因是什么？

In
ddrconfig:7
LP4 MR14:0x4d
LPDDR4, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=4096MB
tdqss: cs0 dqs0: 361ps, dqs1: 265ps, dqs2: 289ps, dqs3: 192ps,
tdqss: cs1 dqs0: 361ps, dqs1: 265ps, dqs2: 313ps, dqs3: 192ps,

change to: 324MHz
PHY drv:clk:38,ca:38,DQ:30,odt:0
vrefinner:41%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58

change to: 528MHz
PHY drv:clk:38,ca:38,DQ:30,odt:0
vrefinner:41%, vrefout:41%
dram drv:40,odt:0
clk skew:0x7d

change to: 780MHz
PHY drv:clk:38,ca:38,DQ:30,odt:0
vrefinner:41%, vrefout:41%
dram drv:40,odt:0
clk skew:0x64

change to: 1560MHz(final freq)
PHY drv:clk:38,ca:38,DQ:30,odt:60
vrefinner:16%, vrefout:29%
dram drv:40,odt:80
vref_ca:00000068
clk skew:0x17
cs 0:
the read training result:
DQS0:0x2d, DQS1:0x2c, DQS2:0x37, DQS3:0x2a,
min  :0x11 0x13 0x13  0xf  0x2  0x5  0x9  0x5 , 0xc  0xd  0x6  0x2  0xb  0x9  0xb  0x5 ,
   0x17 0x19 0x11 0x12  0x8  0x1  0x6  0x7 , 0xb  0xb  0x8  0x1  0x7  0xd  0x8  0xb ,
mid  :0x27 0x29 0x29 0x27 0x18 0x1a 0x1e 0x19 ,0x23 0x24 0x1c 0x18 0x22 0x1e 0x21 0x1b ,
   0x30 0x32 0x2a 0x29 0x1f 0x1a 0x1e 0x1e ,0x22 0x22 0x20 0x19 0x1f 0x22 0x20 0x21 ,
max  :0x3e 0x40 0x40 0x3f 0x2e 0x30 0x33 0x2d ,0x3b 0x3b 0x32 0x2f 0x3a 0x33 0x38 0x31 ,
   0x4a 0x4b 0x43 0x41 0x36 0x33 0x37 0x36 ,0x3a 0x39 0x39 0x31 0x38 0x37 0x38 0x38 ,
range:0x2d 0x2d 0x2d 0x30 0x2c 0x2b 0x2a 0x28 ,0x2f 0x2e 0x2c 0x2d 0x2f 0x2a 0x2d 0x2c ,
   0x33 0x32 0x32 0x2f 0x2e 0x32 0x31 0x2f ,0x2f 0x2e 0x31 0x30 0x31 0x2a 0x30 0x2d ,
the write training result:
DQS0:0x5f, DQS1:0x4b, DQS2:0x50, DQS3:0x3d,
min  :0x94 0x9a 0x9c 0x99 0x8b 0x8e 0x91 0x92 0x90 ,0x7f 0x82 0x7a 0x79 0x84 0x83 0x83 0x7d 0x7a ,
   0x89 0x8b 0x84 0x87 0x79 0x77 0x7a 0x7c 0x7f ,0x73 0x73 0x70 0x6b 0x75 0x77 0x73 0x77 0x6d ,
mid  :0xb0 0xb6 0xb7 0xb4 0xa3 0xa8 0xab 0xac 0xab ,0x9a 0x9a 0x93 0x92 0x9c 0x99 0x9a 0x96 0x94 ,
   0xa5 0xa6 0x9d 0xa0 0x93 0x90 0x92 0x95 0x97 ,0x8e 0x8d 0x8b 0x87 0x8e 0x92 0x8d 0x92 0x87 ,
max  :0xcd 0xd2 0xd2 0xcf 0xbc 0xc3 0xc6 0xc6 0xc6 ,0xb5 0xb3 0xac 0xab 0xb5 0xb0 0xb2 0xb0 0xaf ,
   0xc2 0xc2 0xb7 0xb9 0xad 0xa9 0xaa 0xaf 0xb0 ,0xaa 0xa7 0xa6 0xa3 0xa8 0xad 0xa7 0xad 0xa2 ,
range:0x39 0x38 0x36 0x36 0x31 0x35 0x35 0x34 0x36 ,0x36 0x31 0x32 0x32 0x31 0x2d 0x2f 0x33 0x35 ,
   0x39 0x37 0x33 0x32 0x34 0x32 0x30 0x33 0x31 ,0x37 0x34 0x36 0x38 0x33 0x36 0x34 0x36 0x35 ,
cs 1:
the read training result:
DQS0:0x2d, DQS1:0x29, DQS2:0x33, DQS3:0x28,
min  :0x10 0x13 0x14 0x11  0x2  0x7  0x8  0x5 , 0x9  0xc  0x5  0x1  0xa  0x8  0x9  0x4 ,
   0x16 0x19 0x10  0xf  0x5  0x1  0x3  0x5 , 0xb  0xa  0x7  0x2  0x8  0xe  0xa  0xe ,
mid  :0x26 0x2a 0x2a 0x28 0x17 0x1c 0x1d 0x19 ,0x1f 0x21 0x1a 0x16 0x20 0x1c 0x1f 0x19 ,
   0x2d 0x2f 0x27 0x24 0x1a 0x18 0x1a 0x1a ,0x21 0x20 0x1f 0x18 0x20 0x22 0x20 0x23 ,
max  :0x3d 0x41 0x41 0x40 0x2d 0x32 0x33 0x2e ,0x36 0x37 0x2f 0x2c 0x37 0x30 0x35 0x2f ,
   0x44 0x46 0x3e 0x3a 0x30 0x2f 0x31 0x30 ,0x37 0x36 0x37 0x2f 0x39 0x37 0x37 0x39 ,
range:0x2d 0x2e 0x2d 0x2f 0x2b 0x2b 0x2b 0x29 ,0x2d 0x2b 0x2a 0x2b 0x2d 0x28 0x2c 0x2b ,
   0x2e 0x2d 0x2e 0x2b 0x2b 0x2e 0x2e 0x2b ,0x2c 0x2c 0x30 0x2d 0x31 0x29 0x2d 0x2b ,
the write training result:
DQS0:0x5f, DQS1:0x4b, DQS2:0x50, DQS3:0x3d,
min  :0x93 0x9a 0x9a 0x99 0x89 0x8d 0x8f 0x90 0x8f ,0x7c 0x7c 0x77 0x76 0x7f 0x7d 0x7f 0x7c 0x79 ,
   0x8e 0x90 0x87 0x8a 0x7c 0x7a 0x7c 0x82 0x85 ,0x75 0x74 0x73 0x6e 0x76 0x78 0x73 0x7a 0x6e ,
mid  :0xae 0xb4 0xb4 0xb3 0xa2 0xa7 0xa9 0xa9 0xa8 ,0x97 0x97 0x90 0x8f 0x98 0x95 0x97 0x94 0x92 ,
   0xaa 0xab 0xa1 0xa5 0x97 0x94 0x96 0x9a 0x9e ,0x8e 0x8c 0x8b 0x86 0x8e 0x91 0x8b 0x92 0x86 ,
max  :0xca 0xcf 0xcf 0xcd 0xbb 0xc1 0xc4 0xc2 0xc2 ,0xb3 0xb2 0xaa 0xa9 0xb2 0xad 0xaf 0xad 0xac ,
   0xc7 0xc7 0xbc 0xc1 0xb2 0xaf 0xb0 0xb3 0xb7 ,0xa8 0xa5 0xa3 0x9f 0xa7 0xab 0xa4 0xaa 0x9f ,
range:0x37 0x35 0x35 0x34 0x32 0x34 0x35 0x32 0x33 ,0x37 0x36 0x33 0x33 0x33 0x30 0x30 0x31 0x33 ,
   0x39 0x37 0x35 0x37 0x36 0x35 0x34 0x31 0x32 ,0x33 0x31 0x30 0x31 0x31 0x33 0x31 0x30 0x31 ,
CA Training result:
cs:0 min  :0x4d 0x41 0x42 0x31 0x41 0x2f 0x4d ,0x4b 0x36 0x3d 0x2f 0x3f 0x2e 0x4a ,
cs:0 mid  :0x82 0x82 0x77 0x75 0x76 0x70 0x72 ,0x80 0x7a 0x72 0x6f 0x73 0x6e 0x70 ,
cs:0 max  :0xb7 0xc4 0xad 0xb9 0xac 0xb2 0x97 ,0xb5 0xbe 0xa8 0xaf 0xa8 0xaf 0x97 ,
cs:0 range:0x6a 0x83 0x6b 0x88 0x6b 0x83 0x4a ,0x6a 0x88 0x6b 0x80 0x69 0x81 0x4d ,
cs:1 min  :0x3f 0x45 0x37 0x37 0x36 0x36 0x36 ,0x40 0x3c 0x3a 0x34 0x39 0x34 0x36 ,
cs:1 mid  :0x80 0x80 0x74 0x71 0x74 0x6f 0x6f ,0x81 0x7a 0x74 0x6e 0x74 0x6d 0x6d ,
cs:1 max  :0xc1 0xbc 0xb1 0xac 0xb2 0xa8 0xa9 ,0xc3 0xb9 0xaf 0xa8 0xaf 0xa6 0xa4 ,
cs:1 range:0x82 0x77 0x7a 0x75 0x7c 0x72 0x73 ,0x83 0x7d 0x75 0x74 0x76 0x72 0x6e ,
out
U-Boot SPL board init
U-Boot SPL 2017.09(u-boot commit id: 02accb940fa124f562f99de3acb5cf14face82e5)(sdk version: rk356x_linux_release_20220726_v1.3.0a.xml)-g02accb940f #root (Nov 03 2022 - 18:30:46)
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
Card did not respond to voltage select!
mmc_init: -95, time 9
spl: mmc init failed with error: -95
Trying to boot from MMC1
SPL: A/B-slot: _a, successful: 0, tries-remain: 7
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(6204b6f381...) + OK
## Checking uboot 0x00a00000 ... sha256(84621eb095...) + OK
## Checking fdt 0x00b2fba8 ... sha256(dbcc8ef6d0...) + OK
## Checking atf-2 0xfdcc1000 ... sha256(5563d929da...) + OK
## Checking atf-3 0x0006a000 ... sha256(b04372ab0f...) + OK
## Checking atf-4 0xfdcd0000 ... sha256(b46eaa95b8...) + OK
## Checking atf-5 0xfdcce000 ... sha256(2f8839c803...) + OK
## Checking atf-6 0x00068000 ... sha256(6e9d32ba23...) + OK
## Checking optee 0x08400000 ... sha256(66bbd17352...) + OK
Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00040000)
Total: 152.677 ms

INFO: Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-365-gae7c295ca:derrick.huang
NOTICE:  BL31: Built : 15:37:13, May 17 2022
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: pmu v1 is valid 220114
INFO: dfs DDR fsp_param[0].freq_mhz= 1560MHz
INFO: dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO: dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO: dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO: Using opteed sec cpu_context!
INFO: boot cpu mask: 0
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
I/TC:
I/TC: OP-TEE version: 3.13.0-641-g4167319d3 #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #8 Wed Mar 16 15:14:56 CST 2022 aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0xa00000
INFO: SPSR = 0x3c9

U-Boot 2017.09(u-boot commit id: 02accb940fa124f562f99de3acb5cf14face82e5)(sdk version: rk356x_linux_release_20220726_v1.3.0a.xml)-g02accb940f #root (Nov 03 2022 - 18:30:46 +0800)

Model: Firefly RK3568 Board
PreSerial: 2, raw, 0xfe660000
DRAM:  4 GiB
Sysmem: init
Relocation Offset: ed349000
Relocation fdt: eb9f8880 - eb9fecd8
CR: M/C/I
Using default environment

dwmmc@fe2b0000: 1, dwmmc@fe2c0000: 2, sdhci@fe310000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
DM: v1
boot mode: None
** File not found rk-kernel.dtb **
No resource partition
No resource partition
Failed to load DTB, ret=-19
No find valid DTB, ret=-22
Failed to get kernel dtb, ret=-22
io-domain: OK
Model: Firefly RK3568 Board
rockchip_set_serialno: could not find efuse/otp device
CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
  apll 816000 KHz
  dpll 780000 KHz
  gpll 1188000 KHz
  cpll 1000000 KHz
  npll 24000 KHz
  vpll 24000 KHz
  hpll 24000 KHz
  ppll 200000 KHz
  armclk 816000 KHz
  aclk_bus 150000 KHz
  pclk_bus 50000 KHz
  aclk_top_high 300000 KHz
  aclk_top_low 200000 KHz
  hclk_top 150000 KHz
  pclk_top 50000 KHz
  aclk_perimid 300000 KHz
  hclk_perimid 150000 KHz
  pclk_pmu 100000 KHz
Net: No ethernet found.
Hit key to stop autoboot('CTRL+C'):  0
ANDROID: reboot reason: "(none)"
optee api revision: 2.0
TEEC: Waring: Could not find security partition
Not AVB images, AVB skip
No valid android hdr
Android image load failed
Android boot failed, error -1.
## Booting FIT Image FIT: No fit blob
FIT: No FIT image

## Booting Rockchip Format Image
Could not find kernel partition, ret=-1
Card did not respond to voltage select!
mmc_init: -95, time 9
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:3...
## Error: "mtd_boot" not defined
## Error: "mtd_boot" not defined
## Error: "mtd_boot" not defined
starting USB...
Bus dwc3@fcc00000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus dwc3@fd000000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus dwc3@fcc00000 for devices... 1 USB Device(s) found
scanning bus dwc3@fd000000 for devices... 1 USB Device(s) found
   scanning usb for storage devices... 0 Storage Device(s) found

Device 0: unknown device
No ethernet found.
missing environment variable: pxeuuid
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/00000000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/0000000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/000000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/00000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/0000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/00
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/0
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/default-arm-rockchip
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/default-arm
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/default
No ethernet found.
Config file not found
No ethernet found.
=>

tchip_askquestions

2#核心板系统故障日志_2023-06-27_17_23_48.zip

5.21 KB, 下载次数: 0, 下载积分: 灯泡 -1 , 经验 -1

欢迎光临 Firefly开源社区 (https://dev.t-firefly.com/)