INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9
U-Boot 2017.02-RK3328-06 (Jul 26 2018 - 14:14:04)
CPU: rk3328
cpu version = 1
CPU's clock information:
arm pll = 600000000HZ
general pll = 800000000HZ
ddr pll = 664000000HZ
codec pll = 594000000HZ
new pll = 594000000HZ
Board: Rockchip platform Board
Uboot as second level loader
DRAM: Found dram banks: 1
Adding bank:0000000000200000(000000003fe00000)
Reserve memory for trust os.
dram reserve bank: base = 0x08400000, size = 0x01000000
128 MiB
GIC CPU mask = 0x00000001
SdmmcInit = 0 0
SDCard Boot.
storage init OK!
Using default environment
GetParam
remotectl v0.1
pwm freq=0x11b3dc
pwm_freq_nstime=0x35d
Load FDT from resource image.
power key: bank-16777215 pin-255
rk816_set_regulator_init vdd_arm init uV:1225000
rk805 pre init: 0x19 = 0x08
rk805 pre init: new otp ver, skip operation
pmic:rk805
can't find dts node for pwm0
CPU's clock information:
arm pll = 1200000000HZ
general pll = 800000000HZ
ddr pll = 664000000HZ
codec pll = 594000000HZ
new pll = 594000000HZ
SecureBootEn = 0, SecureBootLock = 0
#Boot ver: 0000-00-00#0.00
empty serial no.
normal boot.
checkKey
vbus = 1
board_fbt_key_pressed: ir_keycode = 0x0, frt = 0
no fuel gauge found
no fuel gauge found
can't find power_ctr node for lcdc0
can't find dts node for deviceinfo
rk_hdmi_register:fail to read deviceinfo
hdmi baseparamer 0x0@0-0
left = 0, right = 0, top = 0, bottom = 0, overscan = 0
panel->left = 100 , panel->right = 100 ,panel->top = 100, panel->bottom = 100, panel->overscan = 100
tve baseparamer 0x0@0-0
[EDID-EXTEND] It is a CEA 861 Series Extension.
no baseparametr,find best edid mode,vic=16
hdmi_dev->video.vic is 16
hdmi_dev_config_video vic 16 color_output 3 color_output_depth 8
pixel clk is 148500000 tmds clk is 148500000
hsync_pol 1 vsync_pol 1
[HDMI] sucess output HDMI.
read logo on state from dts [1]
no fuel gauge found
checkKey
vbus = 1
board_fbt_key_pressed: ir_keycode = 0x0, frt = 0
Hit any key to stop autoboot: 0
load fdt from resouce.
ERROR: [get_entry_ram]: Cannot find logo_kernel.bmp!
Secure Boot state: 0
kernel @ 0x00280000 (0x00e5f008)
ramdisk @ 0x05bf0000 (0x0019d02c)
bootrk: do_bootm_linux...
Loading Device Tree to 0000000005600000, end 000000000561d83d ... OK
Add bank:0000000000200000, 0000000008200000
Add bank:0000000009400000, 0000000036c00000
WARNING: could not set reg FDT_ERR_BADOFFSET.