标题: MIPI屏幕点亮,进不去操作系统,显示FAILED TO BIND [打印本页] 作者: 小名刘川枫 时间: 2019-8-15 11:13 标题: MIPI屏幕点亮,进不去操作系统,显示FAILED TO BIND MIPI屏幕点亮,停留在LOGO界面,进不去操作系统
LOG信息如下,跪求大神帮忙!
U-Boot 2014.10-RK3399-06 (Aug 01 2019 - 20:47:30)
CPU: rk3399
cpu version = 0
CPU's clock information:
aplll = 816000000HZ
apllb = 24000000HZ
gpll = 800000000HZ
aclk_periph_h = 133333333HZ, hclk_periph_h = 66666666HZ, pclk_periph_h = 33333333HZ
aclk_periph_l0 = 100000000HZ, hclk_periph_l0 = 100000000HZ, pclk_periph_l0 = 50000000HZ
hclk_periph_l1 = 100000000HZ, pclk_periph_l1 = 50000000HZ
cpll = 800000000HZ
dpll = 800000000HZ
vpll = 24000000HZ
npll = 24000000HZ
ppll = 676000000HZ
Board: Rockchip platform Board
Uboot as second level loader
DRAM: Found dram banks: 1
Adding bank:0000000000200000(00000000ffe00000)
Reserve memory for trust os.
dram reserve bank: base = 0x08400000, size = 0x01000000
128 MiB
SdmmcInit = 0 20
storage init OK!
Using default environment
GetParam
remotectl v0.1
pwm freq=0xb8320
pwm_freq_nstime=0x52d
Load FDT from resource image.
power key: bank-0 pin-5
can't find dts node for fixed
usb bc: can find node by path: /dwc-control-usb/usb_bc
dwc_otg_check_dpdm: usb bc disconnected
pmic:rk808
can't find dts node for pwm1
set pwm voltage ok,pwm_id =2 vol=1000000,pwm_value=66
CPU's clock information:
aplll = 816000000HZ
apllb = 24000000HZ
gpll = 800000000HZ
aclk_periph_h = 133333333HZ, hclk_periph_h = 66666666HZ, pclk_periph_h = 33333333HZ
aclk_periph_l0 = 100000000HZ, hclk_periph_l0 = 100000000HZ, pclk_periph_l0 = 50000000HZ
hclk_periph_l1 = 100000000HZ, pclk_periph_l1 = 50000000HZ
cpll = 800000000HZ
dpll = 800000000HZ
vpll = 24000000HZ
npll = 24000000HZ
ppll = 676000000HZ
SecureBootEn = 0, SecureBootLock = 0
#Boot ver: 2019-08-01#1.09
empty serial no.
normal boot.
checkKey
vbus = 0
board_fbt_key_pressed: ir_keycode = 0x0, frt = 0
no fuel gauge found
no fuel gauge found
Warn: route-hdmi: connector node is not available
failed to find phy node
pwrctr_name:lcd-rst, parse gpio:1053, atv_val=1,delay:6ms
read logo on state from dts [1]
no fuel gauge found
Using display timing dts
Detailed mode clock 136000 kHz, flags[a]
H: 1080 1106 1108 1144
V: 2160 2168 2172 2176
bus_format: 100a
rk lcdc - 0 dclk set: dclk = 136000000HZ, pll select = 1, div = 1
pwrctr: set lcd-rst(1053)=1,delay:6ms
rockchip_phy_power_on: failed to find phy power on funcs
failed to wait for phy clk lane stop state
ERROR: [get_entry_ram]: Cannot find logo_kernel.bmp!
failed to display kernel logo
checkKey
vbus = 0
board_fbt_key_pressed: ir_keycode = 0x0, frt = 0
got recovery cmd from misc.
load fdt from resouce.
Secure Boot state: 0
kernel @ 0x00280000 (0x01325008)
ramdisk @ 0x05bf0000 (0x007b1b04)
bootrk: do_bootm_linux...
Loading Device Tree to 0000000005600000, end 0000000005616a15 ... OK
Add bank:0000000000200000, 0000000008200000
Add bank:0000000009400000, 00000000eec00000
WARNING: could not set reg FDT_ERR_BADOFFSET.