RK3399 更换eMMC 问题

gogogo777

更换  华存 8G eMMC,重烧系统，不能启动
[BEGIN] 2020-12-21 23:08:33
DDR Version 1.08 20170320
In
Channel 0: DDR3, 800MHz
Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB
Channel 1: DDR3, 800MHz
Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB
256B stride
ch 0 ddrconfig = 0x101, ddrsize = 0x2020
ch 1 ddrconfig = 0x101, ddrsize = 0x2020
pmugrf_os_reg[2] = 0x3AA17AA1, stride = 0xD
OUT
Boot1: 2017-06-09, version: 1.09
CPUId = 0x0
ChipType = 0x10, 1835
SdmmcInit=2 0
BootCapSize=100000
UserCapSize=7456MB
FwPartOffset=2000 , 100000
SdmmcInit=0 20
StorageInit ok = 67806
LoadTrustBL
No find bl30.bin
Load uboot, ReadLba = 2000
Load OK, addr=0x200000, size=0x77d6c
RunBL31 0x10000

NOTICE:  BL31: v1.3(debug):9f93abc
NOTICE:  BL31: Built : 10:18:20, Jul 27 2017
NOTICE:  BL31: Rockchip release version: v1.1
INFO:    GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
INFO:    plat_rockchip_pmu_init(1089): pd status 3e
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
INF [0x0] TEE-CORE:init_primary_helper:337: Initializing (1.1.0-96-g3fbe315-dev #4 Fri Jun 30 00:35:17 UTC 2017 aarch64)


INF [0x0] TEE-CORE:init_primary_helper:338: Release version: 1.1


INF [0x0] TEE-CORE:init_teecore:83: teecore inits done

INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


U-Boot 2014.10-RK3399-06 (Jan 26 2018 - 10:04:18)

CPU: rk3399
cpu version = 0
CPU's clock information:
    aplll = 816000000HZ
    apllb = 24000000HZ
    gpll = 800000000HZ
               aclk_periph_h = 133333333HZ, hclk_periph_h = 66666666HZ, pclk_periph_h = 33333333HZ
               aclk_periph_l0 = 100000000HZ, hclk_periph_l0 = 100000000HZ, pclk_periph_l0 = 50000000HZ
               hclk_periph_l1 = 100000000HZ, pclk_periph_l1 = 50000000HZ
    cpll = 800000000HZ
    dpll = 800000000HZ
    vpll = 24000000HZ
    npll = 24000000HZ
    ppll = 676000000HZ
Board:        Rockchip platform Board
Uboot as second level loader
DRAM:  Found dram banks: 1
Adding bank:0000000000200000(00000000ffe00000)
Reserve memory for trust os.
dram reserve bank: base = 0x08400000, size = 0x01000000
128 MiB
SdmmcInit = 0 20
storage init OK!
Using default environment

GetParam
remotectl v0.1
pwm freq=0xb8320
pwm_freq_nstime=0x52d
Load FDT from resource image.
power key: bank-0 pin-5
can't find dts node for fixed
usb bc: can find node by path: /dwc-control-usb/usb_bc
dwc_otg_check_dpdm: usb bc disconnected
pmic:rk808
can't find dts node for pwm1
set pwm voltage ok,pwm_id =2 vol=1000000,pwm_value=66
CPU's clock information:
    aplll = 816000000HZ
    apllb = 24000000HZ
    gpll = 800000000HZ
               aclk_periph_h = 133333333HZ, hclk_periph_h = 66666666HZ, pclk_periph_h = 33333333HZ
               aclk_periph_l0 = 100000000HZ, hclk_periph_l0 = 100000000HZ, pclk_periph_l0 = 50000000HZ
               hclk_periph_l1 = 100000000HZ, pclk_periph_l1 = 50000000HZ
    cpll = 800000000HZ
    dpll = 800000000HZ
    vpll = 24000000HZ
    npll = 24000000HZ
    ppll = 676000000HZ
SecureBootEn = 0, SecureBootLock = 0

#Boot ver: 2018-01-26#1.09
empty serial no.
normal boot.
checkKey
vbus = 0
board_fbt_key_pressed: ir_keycode = 0x0, frt = 0
no fuel gauge found
no fuel gauge found
failed to find phy node
failed to find panel driver
read logo on state from dts [1]
no fuel gauge found
can't find dts node for deviceinfo
dw_rk_hdmi_register:fail to read deviceinfo
hdmi baseparamer 0x0@0-0
[EDID] extensions block checksum error
[HDMI] parse edid block 1 error-3
no edid message:use default vic config:4
hdmi_dev->video.vic is 4
rk lcdc - 0 dclk set: dclk = 74250000HZ, pll select = 0, div = 1
rockchip_panel_prepare: failed to find panel prepare funcs
hdmi_dev_config_video vic 4 color_output 1 color_output_depth 8
pixel clk is 74250000 tmds clk is 74250000
hsync_pol 1 vsync_pol 1
[HDMI] sucess output HDMI.
PHY PLL not locked: PCLK_ON=1,TMDSCLK_ON=0
rockchip_panel_enable: failed to find panel prepare funcs
ERROR: [get_entry_ram]: Cannot find logo_kernel.bmp!
failed to display kernel logo
checkKey
vbus = 0
board_fbt_key_pressed: ir_keycode = 0x0, frt = 0
got recovery cmd from misc.
load fdt from resouce.
Secure Boot state: 0
kernel   @ 0x00280000 (0x01325008)
ramdisk  @ 0x05bf0000 (0x007b1abc)
bootrk: do_bootm_linux...
   Loading Device Tree to 0000000005600000, end 0000000005615f13 ... OK
Add bank:0000000000200000, 0000000008200000
Add bank:0000000009400000, 00000000eec00000
WARNING: could not set reg FDT_ERR_BADOFFSET.

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Initializing cgroup subsys schedtune
[    0.000000] Linux version 4.4.83 (omy@tchipserver2) (gcc version 4.9 20150123 (prerelease) (GCC) ) #47 SMP PREEMPT Fri Jan 26 09:22:49 CST 2018
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] earlycon: Early serial console at MMIO32 0xff1a0000 (options '')
[    0.000000] bootconsole [uart0] enabled
[    0.000000] hdmi init vic is -1
[    0.000000] Reserved memory: failed to reserve memory for node 'stb-devinfo@00000000': base 0x0000000000000000, size 0 MiB
[    0.000000] cma: Reserved 16 MiB at 0x00000000f7000000
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: Trusted OS migration not required
[    0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc0f6eef000 s45696 r8192 d32128 u86016
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 995336
[    0.000000] Kernel command line: earlycon=uart8250,mmio32,0xff1a0000 swiotlb=1 androidboot.baseband=N/A androidboot.selinux=permissive androidboot.hardware=rk30board androidboot.console=ttyFIQ0 init=/init mtdparts=rk29xxnand:0x00002000@0x00000000(parameter),0x00002000@0x00002000(uboot),0x00002000@0x00004000(trust),0x00002000@0x00006000(misc),0x00008000@0x00008000(resource),0x0000C000@0x00010000(kernel),0x00010000@0x0001C000(boot),0x00010000@0x0002C000(recovery),0x00038000@0x0003C000(backup),0x00040000@0x00074000(cache),0x00300000@0x000B4000(system),0x00008000@0x003B4000(metadata),0x00002000@0x003BC000(baseparamer),-@0x003BE000(userdata) storagemedia=emmc uboot_logo=0x02000000@0xf5c00000 loader.timestamp=2018-01-26_10:04:18 hdmi.vic=-1 SecureBootCheckOk=0
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] software IO TLB [mem 0xf6ea6000-0xf6ee6000] (0MB) mapped at [ffffffc0f6ea6000-ffffffc0f6ee5fff]
[    0.000000] Memory: 3926108K/4044800K available (11838K kernel code, 1428K rwdata, 5440K rodata, 832K init, 1116K bss, 102308K reserved, 16384K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000   (   246 GB)
[    0.000000]       .init : 0xffffff8009170000 - 0xffffff8009240000   (   832 KB)
[    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008c10000   ( 11840 KB)
[    0.000000]     .rodata : 0xffffff8008c10000 - 0xffffff8009170000   (  5504 KB)
[    0.000000]       .data : 0xffffff8009240000 - 0xffffff80093a5008   (  1429 KB)
[    0.000000]     vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
[    0.000000]               0xffffffbdc0008000 - 0xffffffbdc3e00000   (    61 MB actual)
[    0.000000]     fixed   : 0xffffffbffe7fd000 - 0xffffffbffec00000   (  4108 KB)
[    0.000000]     PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000   (    16 MB)
[    0.000000]     memory  : 0xffffffc000200000 - 0xffffffc0f8000000   (  3966 MB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]         Build-time adjustment of leaf fanout to 64.
[    0.000000]         RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] ITS: /interrupt-controller@fee00000/interrupt-controller@fee20000
[    0.000000] ITS: allocated 65536 Devices @f2000000 (psz 64K, shr 0)
[    0.000000] ITS: using cache flushing for cmd queue
[    0.000000] GIC: using LPI property table @0x00000000f2080000
[    0.000000] ITS: Allocated 1792 chunks for LPIs
[    0.000000] CPU0: found redistributor 0 region 0:0x00000000fef00000
[    0.000000] CPU0: using LPI pending table @0x00000000f2090000
[    0.000000] GIC: using cache flushing for LPI property table
[    0.000000] GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
[    0.000000] GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
[    0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop0_frac as parent of dclk_vop0, rate changes may not work
[    0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop1_frac as parent of dclk_vop1, rate changes may not work
[    0.000000] rockchip_cpuclk_pre_rate_change: limiting alt-divider 33 to 31
[    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.001852] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[    0.002814] pid_max: default: 32768 minimum: 301
[    0.003310] Security Framework initialized
[    0.003698] SELinux:  Initializing.
[    0.004129] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.004757] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.006250] Initializing cgroup subsys freezer
[    0.006677] Initializing cgroup subsys debug
[    0.007951] sched-energy: Sched-energy-costs installed from DT
[    0.008501] CPU0: update cpu_capacity 401
[    0.008952] ASID allocator initialised with 65536 entries
[    0.025776] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[    0.027004] Platform MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[    0.039170] Detected VIPT I-cache on CPU1
[    0.039200] CPU1: found redistributor 1 region 0:0x00000000fef20000
[    0.039237] CPU1: using LPI pending table @0x00000000f2200000
[    0.039280] CPU1: update cpu_capacity 401
[    0.039283] CPU1: Booted secondary processor [410fd034]
[    0.049165] Detected VIPT I-cache on CPU2
[    0.049184] CPU2: found redistributor 2 region 0:0x00000000fef40000
[    0.049216] CPU2: using LPI pending table @0x00000000f2230000
[    0.049243] CPU2: update cpu_capacity 401
[    0.049246] CPU2: Booted secondary processor [410fd034]
[    0.059201] Detected VIPT I-cache on CPU3
[    0.059220] CPU3: found redistributor 3 region 0:0x00000000fef60000
[    0.059252] CPU3: using LPI pending table @0x00000000f2270000
[    0.059278] CPU3: update cpu_capacity 401
[    0.059281] CPU3: Booted secondary processor [410fd034]
[    0.069243] Detected PIPT I-cache on CPU4
[    0.069272] CPU4: found redistributor 100 region 0:0x00000000fef80000
[    0.069311] CPU4: using LPI pending table @0x00000000f22b0000
[    0.069353] CPU4: update cpu_capacity 1024
[    0.069356] CPU4: Booted secondary processor [410fd082]
[    0.079268] Detected PIPT I-cache on CPU5
[    0.079286] CPU5: found redistributor 101 region 0:0x00000000fefa0000
[    0.079323] CPU5: using LPI pending table @0x00000000f22e0000
[    0.079351] CPU5: update cpu_capacity 1024
[    0.079353] CPU5: Booted secondary processor [410fd082]
[    0.079435] Brought up 6 CPUs
[    0.091534] SMP: Total of 6 processors activated.
[    0.091976] CPU features: detected feature: GIC system register CPU interface
[    0.092645] CPU: All CPU(s) started at EL2
[    0.093066] alternatives: patching kernel code
[    0.095155] devtmpfs: initialized
[    0.115291] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.116263] futex hash table entries: 2048 (order: 5, 131072 bytes)
[    0.117897] pinctrl core: initialized pinctrl subsystem
[    0.120998] Failed to find legacy iommu devices
[    0.121939] NET: Registered protocol family 16
[    0.123060] schedtune: init normalization constants...
[    0.123546] schedtune: CLUSTER[0-3]      min_pwr:    56 max_pwr:   222
[    0.124157] schedtune: CPU[0]            min_pwr:     0 max_pwr:   222
[    0.124785] schedtune: CPU[1]            min_pwr:     0 max_pwr:   222
[    0.125395] schedtune: CPU[2]            min_pwr:     0 max_pwr:   222
[    0.126006] schedtune: CPU[3]            min_pwr:     0 max_pwr:   222
[    0.126669] schedtune: CLUSTER[4-5]      min_pwr:    65 max_pwr:  1108
[    0.127304] schedtune: CPU[4]            min_pwr:     0 max_pwr:  1108
[    0.127937] schedtune: CPU[5]            min_pwr:     0 max_pwr:  1108
[    0.128570] schedtune: SYSTEM            min_pwr:   121 max_pwr:  4434
[    0.129203] schedtune: using normalization constants mul: 3862781856 sh1: 1 sh2: 12
[    0.129950] schedtune: verify normalization constants...
[    0.130466] schedtune: max_pwr/2^0: 4313 => norm_pwr:  1024
[    0.131006] schedtune: max_pwr/2^1: 2156 => norm_pwr:   511
[    0.131545] schedtune: max_pwr/2^2: 1078 => norm_pwr:   255
[    0.132084] schedtune: max_pwr/2^3:  539 => norm_pwr:   127
[    0.132624] schedtune: max_pwr/2^4:  269 => norm_pwr:    63
[    0.133164] schedtune: max_pwr/2^5:  134 => norm_pwr:    31
[    0.133710] schedtune: configured to support 5 boost groups
[    0.143757] cpuidle: using governor ladder
[    0.154865] cpuidle: using governor menu
[    0.155278] Registered FIQ tty driver
[    0.156006] vdso: 2 pages (1 code @ ffffff8008c16000, 1 data @ ffffff8009244000)
[    0.156759] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.158143] DMA: preallocated 256 KiB pool for atomic allocations
[    0.177747] console [pstore0] enabled
[    0.178346] pstore: Registered ramoops as persistent store backend
[    0.178949] ramoops: attached 0xf0000@0x110000, ecc: 0/0
[    0.181628] sip_fiq_debugger_uart_irq_tf_init error: -2
[    0.182140] fiq debugger bind fiq to trustzone failed: -2
<hit enter to activate fiq debugger>
[    0.183043] console [ttyFIQ0] enabled
[ [    0.183043] console [ttyFIQ0] enabled
[    0.183607] bootconsole [uart0] disabled
   0.183607] bootconsole [uart0] disabled
[    0.184844] Registered fiq debugger ttyFIQ0
[    0.224744] Rockchip hdmi driver version 2.0
.
[    0.226892] iommu: Adding device ff650000.vpu_service to group 0
[    0.226972] iommu: Adding device ff660000.rkvdec to group 1
[    0.227060] iommu: Adding device ff670000.iep to group 2
[    0.227157] iommu: Adding device ff8f0000.vop to group 3
[    0.227238] iommu: Adding device ff900000.vop to group 4
[    0.227335] iommu: Adding device ff910000.isp to group 5
[    0.227410] iommu: Adding device ff920000.isp to group 6
[    0.228078] rk_iommu ff670800.iommu: can't get aclk
[    0.228098] rk_iommu ff670800.iommu: can't get hclk
[    0.228936] SCSI subsystem initialized
[    0.229273] usbcore: registered new interface driver usbfs
[    0.229319] usbcore: registered new interface driver hub
[    0.229398] usbcore: registered new device driver usb
[    0.229740] media: Linux media interface: v0.10
[    0.229780] Linux video capture interface: v2.00
[    0.229909] pps_core: LinuxPPS API ver. 1 registered
[    0.229920] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.229947] PTP clock support registered
[    0.231351] Advanced Linux Sound Architecture Driver Initialized.
[    0.231824] Bluetooth: Core ver 2.21
[    0.231860] NET: Registered protocol family 31
[    0.231871] Bluetooth: HCI device and connection manager initialized
[    0.231888] Bluetooth: HCI socket layer initialized
[    0.231902] Bluetooth: L2CAP socket layer initialized
[    0.231931] Bluetooth: SCO socket layer initialized
[    0.232893] rockchip-cpuinfo cpuinfo: Serial                : fb18f439e4b31347
[    0.233405] clocksource: Switched to clocksource arch_sys_counter
[    0.272631] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[    0.272864] NET: Registered protocol family 2
[    0.273278] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    0.273486] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.273865] TCP: Hash tables configured (established 32768 bind 32768)
[    0.273953] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.274001] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.274194] NET: Registered protocol family 1
[    0.274671] Trying to unpack rootfs image as initramfs...
[    0.610170] Freeing initrd memory: 7876K
[    0.610723] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[    0.610813] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
[    0.613309] audit: initializing netlink subsys (disabled)
[    0.613369] audit: type=2000 audit(0.606:1): initialized
[    0.618465] VFS: Disk quotas dquot_6.6.0
[    0.618585] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.619925] fuse init (API version 7.23)
[    0.620977]
[    0.620977] TEE Core Framework initialization (ver 1:0.1)
[    0.621008] TEE armv7 Driver initialization
[    0.621336] tz_tee_probe: name="armv7sec", id=0, pdev_name="armv7sec.0"
[    0.621352] TEE core: Alloc the misc device "opteearmtz00" (id=0)
[    0.621531] TEE Core: Register the misc device "opteearmtz00" (id=0,minor=62)
[    0.625602] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.625631] io scheduler noop registered
[    0.625801] io scheduler cfq registered (default)
[    0.627043] rockchip-usb2phy ff770000.syscon:usb2-phy@e460: vbus_drv is not assigned
[    0.631555] rockchip-pcie f8000000.pcie: no vpcie3v3 regulator found
[    0.631585] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found
[    0.631608] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found
[    1.153449] rockchip-pcie f8000000.pcie: PCIe link training gen1 timeout!
[    1.154193] rockchip-pcie: probe of f8000000.pcie failed with error -110
[    1.156285] iep: failed to find iep power down clock source.
[    1.157391] IEP Power ON
[    1.157842] IEP Power OFF
[    1.158194] IEP Driver loaded succesfully
[    1.158775] Module initialized.
[    1.159367] rk-vcodec ff650000.vpu_service: probe device
[    1.159423] rk-vcodec ff650000.vpu_service: vpu mmu dec ffffffc0f18f9410
[    1.159593] rk-vcodec ff650000.vpu_service: allocator is drm
[    1.159654] rk-vcodec ff650000.vpu_service: checking hw id 0
[    1.160123] rk-vcodec ff650000.vpu_service: init success
[    1.160673] rk-vcodec ff660000.rkvdec: probe device
[    1.160716] rk-vcodec ff660000.rkvdec: vpu mmu dec ffffffc0f18f9c10
[    1.160862] rk-vcodec ff660000.rkvdec: allocator is drm
[    1.160920] rk-vcodec ff660000.rkvdec: checking hw id 6876
[    1.161226] rk-vcodec ff660000.rkvdec: init success
[    1.162567] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    1.162586] dma-pl330 ff6d0000.dma-controller:         DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
[    1.163952] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    1.163970] dma-pl330 ff6e0000.dma-controller:         DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[    1.165298] Serial: 8250/1.? driver, 5 ports, IRQ sharing disabled
[    1.166879] console [ttyS0] disabled
[    1.166926] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 36, base_baud = 1500000) is a 16550A
[    1.167499] ff1a0000.serial: ttyS2 at MMIO 0xff1a0000 (irq = 37, base_baud = 1500000) is a 16550A
[    1.168058] ff370000.serial: ttyS4 at MMIO 0xff370000 (irq = 40, base_baud = 1500000) is a 16550A
[    1.168415] [drm:drm_core_init] Initialized drm 1.1.0 20060810
[    1.172709] mali ff9a0000.gpu: Failed to get regulator
[    1.172730] mali ff9a0000.gpu: Power control initialization failed
[    1.173012] Unable to detect cache hierarchy from DT for CPU 0
[    1.180817] brd: module loaded
[    1.198866] loop: module loaded
[    1.199393] zram: Added device: zram0
[    1.199932] SCSI Media Changer driver v0.25
[    1.200951] rockchip-pinctrl pinctrl: pin gpio1-8 already requested by ff370000.serial; cannot claim for ff1d0000.spi
[    1.200979] rockchip-pinctrl pinctrl: pin-40 (ff1d0000.spi) status -22
[    1.200995] rockchip-pinctrl pinctrl: could not request pin 40 (gpio1-8) from group spi1-tx  on device rockchip-pinctrl
[    1.201012] rockchip-spi ff1d0000.spi: Error applying setting, reverse things back
[    1.201147] rockchip-spi ff1d0000.spi: Failed to request TX DMA channel
[    1.201162] rockchip-spi ff1d0000.spi: Failed to request RX DMA channel
[    1.201727] register spi return v = :0
[    1.201791] tun: Universal TUN/TAP device driver, 1.6
[    1.201801] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.202773] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
[    1.202791] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
[    1.202804] rk_gmac-dwmac fe300000.ethernet: RX delay(0x1b).
[    1.202835] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
[    1.202998] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
[    1.208016] rk_gmac-dwmac fe300000.ethernet: init for RGMII
[    1.208137] stmmac - user ID: 0x10, Synopsys ID: 0x35
[    1.208148]  Ring mode enabled
[    1.208156]  DMA HW capability register supported
[    1.208165]  Normal descriptors
[    1.208175]  RX Checksum Offload Engine supported (type 2)
[    1.208184]  TX Checksum insertion supported
[    1.208193]  Wake-Up On Lan supported
[    1.208234]  Enable RX Mitigation via HW Watchdog Timer
[    1.276116] libphy: stmmac: probed
[    1.276139] eth%d: PHY ID 001cc915 at 0 IRQ POLL (stmmac-0:00) active
[    1.276153] eth%d: PHY ID 001cc915 at 1 IRQ POLL (stmmac-0:01)
[    1.278261] PPP generic driver version 2.4.2
[    1.278787] PPP BSD Compression module registered
[    1.278811] PPP Deflate Compression module registered
[    1.278841] PPP MPPE Compression module registered
[    1.278865] NET: Registered protocol family 24
[    1.278915] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[    1.278927] CSLIP: code copyright 1989 Regents of the University of California.
[    1.278948] Rockchip WiFi SYS interface (V1.00) ...
[    1.279036] usbcore: registered new interface driver catc
[    1.279081] usbcore: registered new interface driver kaweth
[    1.279099] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[    1.279137] usbcore: registered new interface driver pegasus
[    1.279182] usbcore: registered new interface driver rtl8150
[    1.279226] usbcore: registered new interface driver r8152
[    1.279244] hso: drivers/net/usb/hso.c: Option Wireless
[    1.279304] usbcore: registered new interface driver hso
[    1.279355] usbcore: registered new interface driver asix
[    1.279399] usbcore: registered new interface driver ax88179_178a
[    1.279443] usbcore: registered new interface driver cdc_ether
[    1.279486] usbcore: registered new interface driver cdc_eem
[    1.279532] usbcore: registered new interface driver dm9601
[    1.279585] usbcore: registered new interface driver smsc75xx
[    1.279637] usbcore: registered new interface driver smsc95xx
[    1.279680] usbcore: registered new interface driver gl620a
[    1.279724] usbcore: registered new interface driver net1080
[    1.279769] usbcore: registered new interface driver plusb
[    1.279813] usbcore: registered new interface driver rndis_host
[    1.279857] usbcore: registered new interface driver cdc_subset
[    1.279901] usbcore: registered new interface driver zaurus
[    1.279946] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[    1.280007] usbcore: registered new interface driver int51x1
[    1.280053] usbcore: registered new interface driver kalmia
[    1.280116] usbcore: registered new interface driver ipheth
[    1.280159] usbcore: registered new interface driver sierra_net
[    1.280199] usbcore: registered new interface driver cx82310_eth
[    1.280250] usbcore: registered new interface driver cdc_ncm
[    1.280292] usbcore: registered new interface driver qmi_wwan
[    1.280334] usbcore: registered new interface driver cdc_mbim
[    1.281445] rockchip-dwc3 usb@fe800000: failed to get drvdata dwc3
[    1.298829] rockchip-dwc3 usb@fe900000: fail to get drvdata hcd
[    1.299681] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.299702] ehci-pci: EHCI PCI platform driver
[    1.299785] ehci-platform: EHCI generic platform driver
[    1.303455] ehci-platform fe3c0000.usb: EHCI Host Controller
[    1.303502] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 1
[    1.303725] ehci-platform fe3c0000.usb: irq 30, io mem 0xfe3c0000
[    1.313426] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
[    1.313572] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.313588] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.313601] usb usb1: Product: EHCI Host Controller
[    1.313613] usb usb1: Manufacturer: Linux 4.4.83 ehci_hcd
[    1.313624] usb usb1: SerialNumber: fe3c0000.usb
[    1.314140] hub 1-0:1.0: USB hub found
[    1.314179] hub 1-0:1.0: 1 port detected
[    1.314669] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.314703] ohci-platform: OHCI generic platform driver
[    1.315148] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
[    1.315174] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 2
[    1.315296] ohci-platform fe3e0000.usb: irq 31, io mem 0xfe3e0000
[    1.370905] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    1.370946] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.370961] usb usb2: Product: Generic Platform OHCI controller
[    1.370975] usb usb2: Manufacturer: Linux 4.4.83 ohci_hcd
[    1.370986] usb usb2: SerialNumber: fe3e0000.usb
[    1.371599] hub 2-0:1.0: USB hub found
[    1.371647] hub 2-0:1.0: 1 port detected
[    1.373005] usbcore: registered new interface driver cdc_acm
[    1.373018] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.373101] usbcore: registered new interface driver usblp
[    1.373161] usbcore: registered new interface driver cdc_wdm
[    1.373219] usbcore: registered new interface driver uas
[    1.373322] usbcore: registered new interface driver usb-storage
[    1.373375] usbcore: registered new interface driver ums-alauda
[    1.373479] usbcore: registered new interface driver ums-cypress
[    1.373534] usbcore: registered new interface driver ums-datafab
[    1.373590] usbcore: registered new interface driver ums_eneub6250
[    1.373643] usbcore: registered new interface driver ums-freecom
[    1.373697] usbcore: registered new interface driver ums-isd200
[    1.373749] usbcore: registered new interface driver ums-jumpshot
[    1.373801] usbcore: registered new interface driver ums-karma
[    1.373854] usbcore: registered new interface driver ums-onetouch
[    1.373911] usbcore: registered new interface driver ums-sddr09
[    1.373965] usbcore: registered new interface driver ums-sddr55
[    1.374018] usbcore: registered new interface driver ums-usbat
[    1.374127] usbcore: registered new interface driver usbserial
[    1.374179] usbcore: registered new interface driver usbserial_generic
[    1.374220] usbserial: USB Serial support registered for generic
[    1.374276] usbcore: registered new interface driver ch341
[    1.374316] usbserial: USB Serial support registered for ch341-uart
[    1.374372] usbcore: registered new interface driver cp210x
[    1.374410] usbserial: USB Serial support registered for cp210x
[    1.374479] usbcore: registered new interface driver option
[    1.374516] usbserial: USB Serial support registered for GSM modem (1-port)
[    1.374680] usbcore: registered new interface driver pl2303
[    1.374721] usbserial: USB Serial support registered for pl2303
[    1.374790] usbcore: registered new interface driver trancevibrator
[    1.374808] usb20_otg: version 3.10a 21-DEC-2012
[    1.375063] usb20_host: version 3.10a 21-DEC-2012
[    1.375606] usbcore: registered new interface driver xpad
[    1.375660] usbcore: registered new interface driver usb_acecad
[    1.375712] usbcore: registered new interface driver aiptek
[    1.375760] usbcore: registered new interface driver gtco
[    1.375806] usbcore: registered new interface driver hanwang
[    1.375851] usbcore: registered new interface driver kbtab
[    1.375866] ==gsl_ts_init==
[    1.375895] ret=0
[    1.380348] .. rk pwm remotectl v1.1 init
[    1.380567] input: ff420030.pwm as /devices/platform/ff420030.pwm/input/input0
[    1.380893] remotectl-pwm ff420030.pwm: set irq err, set support_psci to 0 !!
[    1.381004] sensor_register_slave:mma8452,id=17
[    1.381019] sensor_register_slave:lis3dh,id=7
[    1.381033] sensor_register_slave:mma7660,id=18
[    1.381046] sensor_register_slave:lsm303d,id=22
[    1.381060] sensor_register_slave:mpu6880_acc,id=24
[    1.381073] sensor_register_slave:mpu6500_acc,id=25
[    1.381087] sensor_register_slave:lsm330_acc,id=26
[    1.381102] sensor_register_slave:akm8975,id=28
[    1.381115] sensor_register_slave:akm8963,id=29
[    1.381129] sensor_register_slave:l3g4200d,id=43
[    1.381142] sensor_register_slave:l3g20d,id=44
[    1.381156] sensor_register_slave:ewtsa,id=45
[    1.381169] sensor_register_slave:lsm330_gyro,id=48
[    1.381183] sensor_register_slave:cm3217,id=50
[    1.381196] sensor_register_slave:cm3218,id=51
[    1.381828] i2c /dev entries driver
[    1.382885] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
[    1.382950] fan53555-reg: supplied by vcc5v0_sys
[    1.385148] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected!
[    1.385259] fan53555-reg: supplied by vcc5v0_sys
[    1.387441] rk808 0-001b: Pmic Chip id: 0x0
[    1.391109] rk808-regulator rk808-regulator: there is no dvs0 gpio
[    1.391177] rk808-regulator rk808-regulator: there is no dvs1 gpio
[    1.391283] DCDC_REG1: supplied by vcc3v3_sys
[    1.392083] DCDC_REG2: supplied by vcc3v3_sys
[    1.392657] DCDC_REG3: supplied by vcc3v3_sys
[    1.392919] DCDC_REG4: supplied by vcc3v3_sys
[    1.393449] LDO_REG1: supplied by vcc3v3_sys
[    1.394607] LDO_REG2: supplied by vcc3v3_sys
[    1.395602] LDO_REG3: supplied by vcc3v3_sys
[    1.396631] LDO_REG4: supplied by vcc3v3_sys
[    1.397629] LDO_REG5: supplied by vcc3v3_sys
[    1.398629] LDO_REG6: supplied by vcc3v3_sys
[    1.399658] LDO_REG7: supplied by vcc3v3_sys
[    1.400657] LDO_REG8: supplied by vcc3v3_sys
[    1.401661] SWITCH_REG1: supplied by vcc3v3_sys
[    1.401943] SWITCH_REG2: supplied by vcc3v3_sys
[    1.405787] rk808-rtc rk808-rtc: rtc core: registered rk808-rtc as rtc0
[    1.406422] rk3x-i2c ff3c0000.i2c: Initialized RK3xxx I2C bus at ffffff80096fc000
[    1.407292] rk3x-i2c ff110000.i2c: Initialized RK3xxx I2C bus at ffffff80096fe000
[    1.407413] rockchip-pinctrl pinctrl: pin gpio4-17 already requested by ff940000.hdmi; cannot claim for ff130000.i2c
[    1.407432] rockchip-pinctrl pinctrl: pin-145 (ff130000.i2c) status -22
[    1.407448] rockchip-pinctrl pinctrl: could not request pin 145 (gpio4-17) from group i2c3-xfer  on device rockchip-pinctrl
[    1.407464] rk3x-i2c ff130000.i2c: Error applying setting, reverse things back
[    1.407954] rk3x-i2c ff130000.i2c: Initialized RK3xxx I2C bus at ffffff80097d2000
[    1.418904] fusb302 4-0022: port 0 probe success
[    1.418958] rk3x-i2c ff3d0000.i2c: Initialized RK3xxx I2C bus at ffffff80097d4000
[    1.420251] IR NEC protocol handler initialized
[    1.420287] IR RC5(x/sz) protocol handler initialized
[    1.420308] IR RC6 protocol handler initialized
[    1.420327] IR JVC protocol handler initialized
[    1.420346] IR Sony protocol handler initialized
[    1.420363] IR SANYO protocol handler initialized
[    1.420380] IR Sharp protocol handler initialized
[    1.420399] IR MCE Keyboard/mouse protocol handler initialized
[    1.420416] IR XMP protocol handler initialized
[    1.420544] usbcore: registered new interface driver uvcvideo
[    1.420555] USB Video Class driver (1.1.1)
[    1.420577] CamSys driver version: v0.34.3, CamSys head file version: v0.13.0
[    1.426489] __power_supply_register: Expected proper parent device for 'test_ac'
[    1.426673] __power_supply_register: Expected proper parent device for 'test_battery'
[    1.427049] thermal thermal_zone2: power_allocator: sustainable_power will be estimated
[    1.427178] __power_supply_register: Expected proper parent device for 'test_usb'
[    1.430178] rk_tsadcv2_temp_to_code: Invalid conversion table: code=1023, temperature=2147483647
[    1.431129] device-mapper: uevent: version 1.0.3
[    1.431575] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[    1.431716] Bluetooth: HCI UART driver ver 2.3
[    1.431732] Bluetooth: HCI UART protocol H4 registered
[    1.431743] Bluetooth: HCI UART protocol LL registered
[    1.431758] rtk_btusb: RTKBT_RELEASE_NAME: 20170109_TV_ANDROID_6.x
[    1.431768] rtk_btusb: Realtek Bluetooth USB driver module init, version 4.1.2
[    1.431778] rtk_btusb: Register usb char device interface for BT driver
[    1.432030] usbcore: registered new interface driver rtk_btusb
[    1.432513] cpu cpu0: leakage=24
[    1.450309] cpu cpu0: temp=43888, pvtm=150621 (150489 + 132)
[    1.450746] cpu cpu0: pvtm-sel=2
[    1.451158] cpu cpu4: leakage=41
[    1.463467] cpu cpu4: temp=42777, pvtm=155590 (155555 + 35)
[    1.463596] cpu cpu4: pvtm-sel=2
[    1.468982] sdhci: Secure Digital Host Controller Interface driver
[    1.469021] sdhci: Copyright(c) Pierre Ossman
[    1.469038] Synopsys Designware Multimedia Card Interface Driver
[    1.470269] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
[    1.470427] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
[    1.470449] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
[    1.470518] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo
[    1.470560] dwmmc_rockchip fe310000.dwmmc: 'clock-freq-min-max' property was deprecated.
[    1.470613] dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found
[    1.470627] dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found
[    1.471752] dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode.
[    1.471836] dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller.
[    1.471857] dwmmc_rockchip fe320000.dwmmc: Version ID is 270a
[    1.471905] dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 26,32 bit host data width,256 deep fifo
[    1.471933] dwmmc_rockchip fe320000.dwmmc: 'clock-freq-min-max' property was deprecated.
[    1.472039] dwmmc_rockchip fe320000.dwmmc: No vmmc regulator found
[    1.472351] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000 done
[    1.480539] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000 done
[    1.493480] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    1.506851] dwmmc_rockchip fe320000.dwmmc: 1 slots initialized
[    1.507332] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.509391] sdhci-arasan fe330000.sdhci: No vmmc regulator found
[    1.509434] sdhci-arasan fe330000.sdhci: No vqmmc regulator found
[    1.536859] mmc1: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA
[    1.540459] hidraw: raw HID events driver (C) Jiri Kosina
[    1.545061] usbcore: registered new interface driver usbhid
[    1.545100] usbhid: USB HID core driver
[    1.545275] inv_mpu_iio: inv_mpu_init:746
[    1.548287] ashmem: initialized
[    1.551850] ff100000.saradc supply vref not found, using dummy regulator
[    1.554468] rknandbase v1.1 2016-11-08
[    1.555476] usbcore: registered new interface driver snd-usb-audio
[    1.557322] rt5640 1-001c: rt5640 have no aux_det_adc_value defined
[    1.573719] u32 classifier
[    1.573772]     Actions configured
[    1.573821] Netfilter messages via NETLINK v0.30.
[    1.573892] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[    1.574290] ctnetlink v0.93: registering with nfnetlink.
[    1.575178] xt_time: kernel timezone is -0000
[    1.576416] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.576622] arp_tables: (C) 2002 David S. Miller
[    1.577320] Initializing XFRM netlink socket
[    1.577792] NET: Registered protocol family 10
[    1.579026] mip6: Mobile IPv6
[    1.579068] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    1.581082] sit: IPv6 over IPv4 tunneling driver
[    1.581607] NET: Registered protocol family 17
[    1.581642] NET: Registered protocol family 15
[    1.581688] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.582309] mmc1: MAN_BKOPS_EN bit is not set
[    1.582423] Bridge firewalling registered
[    1.582438] Ebtables v2.0 registered
[    1.582726] Bluetooth: RFCOMM TTY layer initialized
[    1.582752] Bluetooth: RFCOMM socket layer initialized
[    1.582790] Bluetooth: RFCOMM ver 1.11
[    1.582811] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    1.582821] Bluetooth: BNEP filters: protocol multicast
[    1.582845] Bluetooth: BNEP socket layer initialized
[    1.582859] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    1.582872] Bluetooth: HIDP socket layer initialized
[    1.582908] l2tp_core: L2TP core driver, V2.0
[    1.582928] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[    1.582944] [WLAN_RFKILL]: Enter rfkill_wlan_init
[    1.583375] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[    1.583499] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6356s
[    1.583511] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[    1.583521] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[    1.583596] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 3, flags = 0.
[    1.583606] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[    1.583618] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[    1.583690] [BT_RFKILL]: Enter rfkill_rk_init
[    1.584201] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 83.
[    1.584245] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 9.
[    1.584276] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 90.
[    1.584307] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 4.
[    1.584688] [BT_RFKILL]: Request irq for bt wakeup host
[    1.584731] [BT_RFKILL]: BT_WAKE_HOST IRQ fired
[    1.584751] [BT_RFKILL]: ** disable irq
[    1.584893] [BT_RFKILL]: bt_default device registered.
[    1.585044] sensor_register_slave:mpu6880_gyro,id=47
[    1.585507] Registered cp15_barrier emulation handler
[    1.585598] Registered setend emulation handler
[    1.586668] registered taskstats version 1
[    1.593482] rockchip ion idev is NULL
[    1.593502] rga2 ff680000.rga: rga ion client create success!
[    1.593815] rga: Driver loaded successfully ver:3.02
[    1.595819] rockchip-usb2phy ff770000.syscon:usb2-phy@e450: vbus_drv is not assigned
[    1.599655] mmc1: new HS400 MMC card at address 0001
[    1.600215] rockchip-drm display-subsystem: bound ff900000.vop (ops vop_component_ops)
[    1.600616] mmcblk1: mmc1:0001 MMC8GB 7.28 GiB
[    1.600656] rockchip-drm display-subsystem: bound ff8f0000.vop (ops vop_component_ops)
[    1.601209] mmcblk1boot0: mmc1:0001 MMC8GB partition 1 4.00 MiB
[    1.601468] i2c i2c-9: of_i2c: modalias failure on /hdmi@ff940000/ports
[    1.601520] dwhdmi-rockchip ff940000.hdmi: registered DesignWare HDMI I2C bus driver
[    1.601660] dwhdmi-rockchip ff940000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[    1.601780] mmcblk1boot1: mmc1:0001 MMC8GB partition 2 4.00 MiB
[    1.602336] mmcblk1rpmb: mmc1:0001 MMC8GB partition 3 4.00 MiB
[    1.602752] rkpart: partition size too small (4)
[    1.602767]  parameter: 0x000000000 -- 0x000400000 (4 MB)
[    1.602778]      uboot: 0x000400000 -- 0x000800000 (4 MB)
[    1.602788]      trust: 0x000800000 -- 0x000c00000 (4 MB)
[    1.602798]       misc: 0x000c00000 -- 0x001000000 (4 MB)
[    1.602808]   resource: 0x001000000 -- 0x002000000 (16 MB)
[    1.602818]     kernel: 0x002000000 -- 0x003800000 (24 MB)
[    1.602828]       boot: 0x003800000 -- 0x005800000 (32 MB)
[    1.602838]   recovery: 0x005800000 -- 0x007800000 (32 MB)
[    1.602849]     backup: 0x007800000 -- 0x00e800000 (112 MB)
[    1.602859]      cache: 0x00e800000 -- 0x016800000 (128 MB)
[    1.602868]     system: 0x016800000 -- 0x076800000 (1536 MB)
[    1.602879]   metadata: 0x076800000 -- 0x077800000 (16 MB)
[    1.602889] baseparamer: 0x077800000 -- 0x077c00000 (4 MB)
[    1.602899]   userdata: 0x077c00000 -- 0x1d1c00000 (5536 MB)
[    1.602957]  mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14
[    1.607095] rockchip-drm display-subsystem: bound ff940000.hdmi (ops dw_hdmi_rockchip_ops)
[    1.608127] rockchip-drm display-subsystem: bound fec00000.dp (ops cdn_dp_component_ops)
[    1.608165] [drm:drm_vblank_init] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    1.608192] [drm:drm_vblank_init] No driver support for vblank timestamp query.
[    1.609026] cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] Not connected. Disabling cdn
[    1.623627] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    1.750137] usb 1-1: New USB device found, idVendor=1a40, idProduct=0201
[    1.750239] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    1.750268] usb 1-1: Product: USB 2.0 Hub [MTT]
[    1.751573] hub 1-1:1.0: USB hub found
[    1.751897] hub 1-1:1.0: 7 ports detected
[    2.091896] vendor storage:20160801 ret = 0
[    2.093376] rockchip-drm display-subsystem: fb0:  frame buffer device
[    2.109183] mali ff9a0000.gpu: leakage=30
[    2.133037] mali ff9a0000.gpu: temp=41666, pvtm=122130 (122130 + 0)
[    2.134549] mali ff9a0000.gpu: pvtm-sel=1
[    2.136257] mali ff9a0000.gpu: GPU identified as 0x0860 r2p0 status 0
[    2.137537] I : [File] : drivers/gpu/arm/midgard/backend/gpu/mali_kbase_devfreq.c; [Line] : 284; [Func] : kbase_devfreq_init(); success initing power_model_simple.
[    2.139141] mali ff9a0000.gpu: Probed as mali0
[    2.147527] xhci-hcd xhci-hcd.10.auto: xHCI Host Controller
[    2.147668] xhci-hcd xhci-hcd.10.auto: new USB bus registered, assigned bus number 3
[    2.148097] xhci-hcd xhci-hcd.10.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x02030010
[    2.148218] xhci-hcd xhci-hcd.10.auto: irq 233, io mem 0xfe800000
[    2.148550] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    2.148584] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.148612] usb usb3: Product: xHCI Host Controller
[    2.148637] usb usb3: Manufacturer: Linux 4.4.83 xhci-hcd
[    2.148662] usb usb3: SerialNumber: xhci-hcd.10.auto
[    2.149934] hub 3-0:1.0: USB hub found
[    2.150016] hub 3-0:1.0: 1 port detected
[    2.150750] xhci-hcd xhci-hcd.10.auto: xHCI Host Controller
[    2.150795] xhci-hcd xhci-hcd.10.auto: new USB bus registered, assigned bus number 4
[    2.150955] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.151205] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[    2.151238] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.151264] usb usb4: Product: xHCI Host Controller
[    2.151289] usb usb4: Manufacturer: Linux 4.4.83 xhci-hcd
[    2.151314] usb usb4: SerialNumber: xhci-hcd.10.auto
[    2.152624] hub 4-0:1.0: USB hub found
[    2.152704] hub 4-0:1.0: 1 port detected
[    2.155962] xhci-hcd xhci-hcd.10.auto: remove, state 1
[    2.156025] usb usb4: USB disconnect, device number 1
[    2.180809] xhci-hcd xhci-hcd.10.auto: Host not halted after 16000 microseconds.
[    2.180913] xhci-hcd xhci-hcd.10.auto: Host controller not halted, aborting reset.
[    2.181040] xhci-hcd xhci-hcd.10.auto: USB bus 4 deregistered
[    2.181080] xhci-hcd xhci-hcd.10.auto: remove, state 1
[    2.181126] usb usb3: USB disconnect, device number 1
[    2.182072] xhci-hcd xhci-hcd.10.auto: USB bus 3 deregistered
[    2.189557] xhci-hcd xhci-hcd.11.auto: xHCI Host Controller
[    2.189658] xhci-hcd xhci-hcd.11.auto: new USB bus registered, assigned bus number 3
[    2.189982] xhci-hcd xhci-hcd.11.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x02030010
[    2.190162] xhci-hcd xhci-hcd.11.auto: irq 234, io mem 0xfe900000
[    2.190413] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    2.190437] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.190456] usb usb3: Product: xHCI Host Controller
[    2.190473] usb usb3: Manufacturer: Linux 4.4.83 xhci-hcd
[    2.190490] usb usb3: SerialNumber: xhci-hcd.11.auto
[    2.191396] hub 3-0:1.0: USB hub found
[    2.191453] hub 3-0:1.0: 1 port detected
[    2.191892] xhci-hcd xhci-hcd.11.auto: xHCI Host Controller
[    2.191924] xhci-hcd xhci-hcd.11.auto: new USB bus registered, assigned bus number 4
[    2.192035] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.192204] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[    2.192226] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.192245] usb usb4: Product: xHCI Host Controller
[    2.192262] usb usb4: Manufacturer: Linux 4.4.83 xhci-hcd
[    2.192279] usb usb4: SerialNumber: xhci-hcd.11.auto
[    2.193093] hub 4-0:1.0: USB hub found
[    2.193146] hub 4-0:1.0: 1 port detected
[    2.198051] ehci-platform fe380000.usb: EHCI Host Controller
[    2.198098] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 5
[    2.198379] ehci-platform fe380000.usb: irq 28, io mem 0xfe380000
[    2.207073] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
[    2.207421] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[    2.207444] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.207463] usb usb5: Product: EHCI Host Controller
[    2.207480] usb usb5: Manufacturer: Linux 4.4.83 ehci_hcd
[    2.207497] usb usb5: SerialNumber: fe380000.usb
[    2.208552] hub 5-0:1.0: USB hub found
[    2.208655] hub 5-0:1.0: 1 port detected
[    2.209978] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
[    2.210022] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 6
[    2.210327] ohci-platform fe3a0000.usb: irq 29, io mem 0xfe3a0000
[    2.268108] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    2.268238] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.268268] usb usb6: Product: Generic Platform OHCI controller
[    2.268295] usb usb6: Manufacturer: Linux 4.4.83 ohci_hcd
[    2.268319] usb usb6: SerialNumber: fe3a0000.usb
[    2.269748] hub 6-0:1.0: USB hub found
[    2.269831] hub 6-0:1.0: 1 port detected
[    2.272608] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
[    2.272877] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
[    2.272918] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
[    2.272982] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo
[    2.273034] dwmmc_rockchip fe310000.dwmmc: 'clock-freq-min-max' property was deprecated.
[    2.273136] dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found
[    2.273162] dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found
[    2.273833] dwmmc_rockchip fe310000.dwmmc: allocated mmc-pwrseq
[    2.287132] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    2.300573] dwmmc_rockchip fe310000.dwmmc: 1 slots initialized
[    2.318051] asoc-simple-card rt5640-sound: rt5640-aif1 <-> ff890000.i2s mapping ok
[    2.325675] input: rockchip,rt5640-codec Headphone Jack as /devices/platform/rt5640-sound/sound/card0/input1
[    2.328479] asoc-simple-card spdif-sound: dit-hifi <-> ff870000.spdif mapping ok
[    2.332547] rk-hdmi-dp-sound hdmi-dp-sound: control 3:0:0:ELD:0 is already present
[    2.332648] hdmi-audio-codec hdmi-audio-codec.9.auto: ASoC: Failed to add ELD: -16
[    2.333876] rk-hdmi-dp-sound hdmi-dp-sound: multicodec <-> ff8a0000.i2s mapping ok
[    2.333972] hdmi-audio-codec hdmi-audio-codec.9.auto: ASoC: Failed to create Playback debugfs file
[    2.337198]
[    2.337290] =======================================================
[    2.337310] ==== Launching Wi-Fi driver! (Powered by Rockchip) ====
[    2.337328] =======================================================
[    2.337347] Realtek 8188EU USB WiFi driver (Powered by Rockchip,Ver 2.20.WFD) init.
[    2.337369] [WLAN_RFKILL]: rockchip_wifi_power: 1
[    2.337389] [WLAN_RFKILL]: wifi turn on power. -1
[    2.337405] RTL871X: module init start
[    2.337422] RTL871X: rtl8188eu v4.3.24_16705.20160509
[    2.337588] dhd_module_init: in Dongle Host Driver, version 1.363.59.144.10 (r)
[    2.337631] ======== dhd_wlan_init_plat_data ========
[    2.337653] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
[    2.337674] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
[    2.337696] usbcore: registered new interface driver rtl8188eu
[    2.337701] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter
[    2.337714] dhd_wlan_init_gpio: host_oob_irq: 73
[    2.337719] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
[    2.337723] dhd_wifi_platform_load: Enter
[    2.337758] Power-up adapter 'DHD generic adapter'
[    2.337791] RTL871X: module init ret=0
[    2.337822] otg_wakelock_init: No USB transceiver found
[    2.337842] wifi_platform_set_power = 1
[    2.337863] ======== PULL WL_REG_ON(-1) HIGH! ========
[    2.337884] [WLAN_RFKILL]: rockchip_wifi_power: 1
[    2.337903] [WLAN_RFKILL]: wifi turn on power. -1
[    2.338041] sensor_init: Probe name sensors
[    2.338072] sensor-dev.c v1.4 add angle calculation support between two gsensors 2013-09-01
[    2.339674] rk808-rtc rk808-rtc: setting system clock to 2013-01-18 08:50:03 UTC (1358499003)
[    2.341915] It doesn't contain Rogue gpu
[    2.347282] mmc2: queuing unknown CIS tuple 0x80 (2 bytes)
[    2.348945] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
[    2.350601] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
[    2.353559] mmc2: queuing unknown CIS tuple 0x80 (7 bytes)

u?









[    2.408554] mmc_host mmc2: Bus speed (slot 0) = 200000000Hz (slot req 208000000Hz, actual 200000000HZ div = 0)