Firefly开源社区

打印 上一主题 下一主题

[技术讨论] RK3568X开发板烧写android 11 sdk固件后,wifi扫描出错

32

积分

0

威望

0

贡献

技术小白

积分
32

RK3568X开发板烧写android 11 sdk固件后,wifi扫描出错

发表于 2021-9-9 14:44:48      浏览:7199 | 回复:4        打印      只看该作者   [复制链接] 楼主
1.开发板上接的有天线,硬件电压、时钟信号都量过,没有问题
2.defconfig配置添加了wifi驱动
--- Broadcom Wireless Device Driver Support      
    <M>   Select driver version for ap6xxx chips  
    < >     stable version (wifi5)
    <M>     support wifi6(80211ax)                                                                          
    < >     support WiFi keepalive during host shutdown
    (/vendor/etc/firmware/fw_bcmdhd.bin) Firmware path                                          
    (/vendor/etc/firmware/nvram.txt) NVRAM path                                                                        
     [ ]   Enable wlan1 support

3.内核输出部分信息如下:
[   21.832299] dhd_open: Enter wlan0
[   21.832347] dhd_open : no mutex held. set lock
[   21.832356] \x0aDongle Host Driver, version 100.10.545.9 (r826445-20200316-8)
[   21.832372] [dhd-wlan0] wl_android_wifi_on : in g_wifi_on=0
[   21.832377] wifi_platform_set_power = 1, delay: 200 msec
[   21.832385] ======== PULL WL_REG_ON(-1) HIGH! ========
[   21.832389] drivers/net/wireless/rockchip_wlan/rkwifi/bcmdhd_wifi6/dhd_gpio.c 34
[   21.832394] [WLAN_RFKILL]: rockchip_wifi_power: 1
[   21.832399] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
[   21.832404] [WLAN_RFKILL]: wifi turn on power [GPIO-1-0]
[   22.138256] sdio_reset_comm():
[   22.361504] mmc_host mmc3: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[   22.378415] mmc_host mmc3: Bus speed (slot 0) = 375000Hz (slot req 100000Hz, actual 93750HZ div = 2)
[   22.394795] mmc_host mmc3: Bus speed (slot 0) = 375000Hz (slot req 375000Hz, actual 375000HZ div = 0)
[   22.406585] mmc3: queuing unknown CIS tuple 0x80 (2 bytes)
[   22.408276] mmc3: queuing unknown CIS tuple 0x80 (3 bytes)
[   22.410061] mmc3: queuing unknown CIS tuple 0x80 (3 bytes)
[   22.413071] mmc3: queuing unknown CIS tuple 0x80 (7 bytes)
[   22.494972] mmc_host mmc3: Bus speed (slot 0) = 148500000Hz (slot req 150000000Hz, actual 148500000HZ div = 0)
[   22.888104] dwmmc_rockchip fe000000.dwmmc: Successfully tuned phase to 240
[   22.888189] sdioh_start: set sd_f2_blocksize 256
[   22.888428] \x0a\x0adhd_bus_devreset: == Power ON ==
[   22.888530] F1 signature read @0x18000000=0x1042aae8
[   22.891642] F1 signature OK, socitype:0x1 chip:0xaae8 rev:0x2 pkg:0x4
[   22.892038] DHD: dongle ram size is set to 1310720(orig 1310720) at 0x170000
[   22.892086] dhd_bus_devreset: making DHD_BUS_DOWN
[   22.892118] dhdsdio_probe_init: making DHD_BUS_DOWN
[   22.897194] [dhd] dhd_conf_read_config : Ignore config file /vendor/etc/firmware/config.txt
[   22.897230] [dhd] dhd_conf_set_path_params : Final fw_path=/vendor/etc/firmware/fw_bcm43752a2_ag.bin
[   22.897236] [dhd] dhd_conf_set_path_params : Final nv_path=/vendor/etc/firmware/nvram_ap6275s.txt
[   22.897240] [dhd] dhd_conf_set_path_params : Final clm_path=/vendor/etc/firmware/clm_bcm43752a2_ag.blob
[   22.897244] [dhd] dhd_conf_set_path_params : Final conf_path=/vendor/etc/firmware/config.txt
[   22.897761] dhd_os_open_image1: /vendor/etc/firmware/fw_bcm43752a2_ag.bin (757448 bytes) open success
[   22.946747] dhd_os_open_image1: /vendor/etc/firmware/nvram_ap6275s.txt (8354 bytes) open success
[   22.947270] NVRAM version:  AP6275S_NVRAM_V1.4_20201116
[   22.947874] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
[   23.009332] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
[   23.009615] bcmsdh_oob_intr_register: HW_OOB irq=113 flags=0x4
[   23.009835] get_mem_val_from_file: File [/data/misc/wifi/.memdump.info] doesn't exist
[   23.009854] dhd_get_memdump_info: MEMDUMP ENABLED = 3
[   23.012195] dhd_tcpack_suppress_set: TCP ACK Suppress mode 2 -> mode 1
[   23.014340] dhd_os_open_image1: /vendor/etc/firmware/clm_bcm43752a2_ag.blob (28865 bytes) open success
[   23.015830] dhd_check_current_clm_data: ----- This FW is not included CLM data -----
[   23.050806] dhd_check_current_clm_data: ----- This FW is included CLM data -----
[   23.052969] Firmware up: op_mode=0x0005, MAC=10:2c:6b:10:c4:e6
[   23.061103] dhd_preinit_ioctls: event_log_max_sets: 26 ret: 0
[   23.082907] Driver: 100.10.545.9 (r826445-20200316-8)\x0a  Firmware: wl0: Oct 23 2020 15:06:26 version 18.35.387.23.14 (70c9ec1@shgit) (wlan=r880297) FWID 01-217b144d\x0a  CLM: 9.9.5_SS (2019-12-04 01:26:12)
[   23.084748] dhd_txglom_enable: enable 1
[   23.084776] [dhd] dhd_conf_set_txglom_params : txglom_mode=copy
[   23.084783] [dhd] dhd_conf_set_txglom_params : txglomsize=36, deferred_tx_len=0
[   23.084788] [dhd] dhd_conf_set_txglom_params : txinrx_thres=128, dhd_txminmax=-1
[   23.084793] [dhd] dhd_conf_set_txglom_params : tx_max_offset=0, txctl_tmo_fix=300
[   23.084802] [dhd] dhd_conf_get_disable_proptx : fw_proptx=1, disable_proptx=-1
[   23.086877] dhd_wlfc_hostreorder_init(): successful bdcv2 tlv signaling, 64
[   23.091777] dhd_pno_init: Support Android Location Service
[   23.117621] rtt_do_get_ioctl: failed to send getbuf proxd iovar (CMD ID : 1), status=-23
[   23.117652] dhd_rtt_init : FTM is not supported
[   23.118232] dhd_rtt_ftm_config : failed to set config
[   23.120794] dhd_ecounter_autoconfig Ecounter autoconfig in FW not supported
[   23.121454] failed to start ecounters
[   23.121481] dhd_ecounter_configure Ecounters start failed
[   23.126577] [INIT] logset:8 is preserve/chatty
[   23.127734] [INIT] logset:10 is preserve/chatty
[   23.136817] [dhd] dhd_conf_set_country : set country CN, revision 0
[   23.141110] [dhd] dhd_conf_set_country : Country code: CN (CN/0)
[   23.147849] [dhd-wlan0] wl_android_wifi_on : Success
[   23.199435] dhd_open : the lock is released.
[   23.199464] dhd_open: Exit wlan0 ret=0
[   23.199470] [wlan0] tx queue started
[   23.210353] init: Unable to set property 'vendor.wlan.driver.version' from uid:1010 gid:1010 pid:266: SELinux permission check failed
[   23.210373] type=1107 audit(1631150158.940:81): uid=0 auid=4294967295 ses=4294967295 subj=u:r:init:s0 msg='avc: denied { set } for property=vendor.wlan.driver.version pid=266 uid=1010 gid=1010 scontext=u:r:hal_wifi_default:s0 tcontext=ubject_r:vendor_default_prop:s0 tclass=property_service permissive=0'
[   23.247611] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[   23.269489] init: starting service 'wpa_supplicant'...
[   23.270332] init: Created socket '/dev/socket/wpa_wlan0', mode 660, user 1010, group 1010
[   23.273293] init: Control message: Processed ctl.interface_start for 'android.hardware.wifi.supplicant@1.0::ISupplicant/default' from pid: 155 (/system/bin/hwservicemanager)
[   23.360519] capability: warning: `wpa_supplicant' uses 32-bit capabilities (legacy support in use)
[   23.555030] P2P interface registered
[   23.555058] wl_cfgp2p_add_p2p_disc_if: wdev: 0000000013773f93, wdev->net:           (null)
[   23.633048] dhd_dbg_attach_pkt_monitor, 1502
[   23.670717] net_os_enable_packet_filter: val = 0
[   23.671249] net_os_rxfilter_add_remove: add_remove = 0, num = 2
[   23.672536] net_os_enable_packet_filter: val = 1
[   23.673027] net_os_enable_packet_filter: val = 0
[   23.673552] net_os_rxfilter_add_remove: add_remove = 0, num = 3
[   23.679298] net_os_enable_packet_filter: val = 1
[   23.680115] dhd_set_suspend: Remove extra suspend setting
[   23.680776] dhd_enable_packet_filter: enter, value = 0
[   23.740908] type=1400 audit(1631150159.470:82): avc: denied { read } for comm="Binder:177_2" name="wakeup2" dev="sysfs" ino=15967 scontext=u:r:system_suspend:s0 tcontext=ubject_r:sysfs:s0 tclass=dir permissive=0
[   23.742095] type=1400 audit(1631150159.473:83): avc: denied { read } for comm="Binder:177_2" name="wakeup9" dev="sysfs" ino=24427 scontext=u:r:system_suspend:s0 tcontext=ubject_r:sysfs:s0 tclass=dir permissive=0
[   23.744804] type=1400 audit(1631150159.473:84): avc: denied { read } for comm="Binder:177_2" name="wakeup12" dev="sysfs" ino=25197 scontext=u:r:system_suspend:s0 tcontext=ubject_r:sysfs_power:s0 tclass=dir permissive=0
[   23.750300] type=1400 audit(1631150159.476:85): avc: denied { read } for comm="Binder:177_2" name="wakeup5" dev="sysfs" ino=23167 scontext=u:r:system_suspend:s0 tcontext=ubject_r:sysfs:s0 tclass=dir permissive=0
[   23.750470] type=1400 audit(1631150159.476:86): avc: denied { read } for comm="Binder:177_2" name="wakeup10" dev="sysfs" ino=25057 scontext=u:r:system_suspend:s0 tcontext=ubject_r:sysfs_power:s0 tclass=dir permissive=0
[   23.750568] type=1400 audit(1631150159.480:87): avc: denied { read } for comm="Binder:177_2" name="wakeup13" dev="sysfs" ino=27055 scontext=u:r:system_suspend:s0 tcontext=ubject_r:sysfs:s0 tclass=dir permissive=0
[   23.750658] type=1400 audit(1631150159.480:88): avc: denied { read } for comm="Binder:177_2" name="wakeup11" dev="sysfs" ino=25113 scontext=u:r:system_suspend:s0 tcontext=ubject_r:sysfs_power:s0 tclass=dir permissive=0
[   23.777120] audit: audit_lost=1 audit_rate_limit=5 audit_backlog_limit=64
[   23.777157] audit: rate limit exceeded
[   23.837497] init: processing action (vendor.wifi.direct.interface=p2p-dev-wlan0) from (/vendor/etc/init/hw/init.connectivity.rc:53)
[   31.850928] type=1400 audit(1631150167.580:98): avc: denied { read } for comm="Binder:177_2" name="wakeup2" dev="sysfs" ino=15967 scontext=u:r:system_suspend:s0 tcontext=ubject_r:sysfs:s0 tclass=dir permissive=0
[   31.854285] type=1400 audit(1631150167.583:99): avc: denied { read } for comm="Binder:177_2" name="wakeup9" dev="sysfs" ino=24427 scontext=u:r:system_suspend:s0 tcontext=ubject_r:sysfs:s0 tclass=dir permissive=0
[   31.857999] type=1400 audit(1631150167.586:100): avc: denied { read } for comm="Binder:177_2" name="wakeup12" dev="sysfs" ino=25197 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs_power:s0 tclass=dir permissive=0
[   31.858657] type=1400 audit(1631150167.590:101): avc: denied { read } for comm="Binder:177_2" name="wakeup5" dev="sysfs" ino=23167 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs:s0 tclass=dir permissive=0
[   31.858767] type=1400 audit(1631150167.590:102): avc: denied { read } for comm="Binder:177_2" name="wakeup10" dev="sysfs" ino=25057 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs_power:s0 tclass=dir permissive=0
[   31.861621] audit: audit_lost=10 audit_rate_limit=5 audit_backlog_limit=64
[   31.861638] audit: rate limit exceeded
[   31.935688] dhd_set_suspend: Remove extra suspend setting
[   31.939853] dhd_enable_packet_filter: enter, value = 0
[   32.040505] dhd_set_suspend: force extra Suspend setting
[   32.040546] dhd_enable_packet_filter: enter, value = 1
[   32.308657] gsensor_mxc6655 5-0015: set sensor poll time to 66ms
[   32.314426] gsensor_mxc6655 5-0015: sensor on: starting poll sensor data 62ms
[   32.366453] dhd_set_suspend: Remove extra suspend setting
[   32.368005] dhd_enable_packet_filter: enter, value = 0
[   33.764785] vcc5v0_otg: disabling
[   33.764816] vcc3v3_lcd1_n: disabling
[   33.764829] pcie30_3v3: disabling
[   40.254000] [dhd-wlan0] wl_run_escan : LEGACY_SCAN sync ID: 0, bssidx: 0
[   40.255456] [dhd] CFG80211-ERROR) wl_run_escan :  Escan set error (-37)
[   40.255552] [dhd] CFG80211-ERROR) wl_run_escan : scan error (-37)
[   40.255583] [dhd] CFG80211-ERROR) wl_cfg80211_scan : scan error (-11)
[   40.324444] [dhd-wlan0] wl_run_escan : LEGACY_SCAN sync ID: 1, bssidx: 0
[   40.327027] [dhd] CFG80211-ERROR) wl_run_escan :  Escan set error (-37)
[   40.327065] [dhd] CFG80211-ERROR) wl_run_escan : scan error (-37)
[   40.327077] [dhd] CFG80211-ERROR) wl_cfg80211_scan : scan error (-11)
[   50.302530] [dhd-wlan0] wl_run_escan : LEGACY_SCAN sync ID: 2, bssidx: 0
[   50.304042] [dhd] CFG80211-ERROR) wl_run_escan :  Escan set error (-37)
[   50.304070] [dhd] CFG80211-ERROR) wl_run_escan : scan error (-37)
[   50.304082] [dhd] CFG80211-ERROR) wl_cfg80211_scan : scan error (-11)
[   50.366329] [dhd-wlan0] wl_run_escan : LEGACY_SCAN sync ID: 3, bssidx: 0
[   50.367746] [dhd] CFG80211-ERROR) wl_run_escan :  Escan set error (-37)
[   50.367770] [dhd] CFG80211-ERROR) wl_run_escan : scan error (-37)
[   50.367782] [dhd] CFG80211-ERROR) wl_cfg80211_scan : scan error (-11)
[   60.365075] [dhd-wlan0] wl_run_escan : LEGACY_SCAN sync ID: 4, bssidx: 0
[   60.366480] [dhd] CFG80211-ERROR) wl_run_escan :  Escan set error (-37)
[   60.366511] [dhd] CFG80211-ERROR) wl_run_escan : scan error (-37)
[   60.366528] [dhd] CFG80211-ERROR) wl_cfg80211_scan : scan error (-11)
[   60.419189] [dhd-wlan0] wl_run_escan : LEGACY_SCAN sync ID: 5, bssidx: 0
[   60.420560] [dhd] CFG80211-ERROR) wl_run_escan :  Escan set error (-37)
[   60.420661] [dhd] CFG80211-ERROR) wl_run_escan : scan error (-37)
[   60.420701] [dhd] CFG80211-ERROR) wl_cfg80211_scan : scan error (-11)
[   65.559530] healthd: battery l=50 v=3 t=2.6 h=2 st=3 fc=100 chg=au
[   70.413996] [dhd-wlan0] wl_run_escan : LEGACY_SCAN sync ID: 6, bssidx: 0
[   70.414560] [dhd] CFG80211-ERROR) wl_run_escan :  Escan set error (-37)
[   70.414583] [dhd] CFG80211-ERROR) wl_run_escan : scan error (-37)
[   70.414601] [dhd] CFG80211-ERROR) wl_cfg80211_scan : scan error (-11)
[   70.453069] [dhd-wlan0] wl_run_escan : LEGACY_SCAN sync ID: 7, bssidx: 0
[   70.456372] [dhd] CFG80211-ERROR) wl_run_escan :  Escan set error (-37)
[   70.456409] [dhd] CFG80211-ERROR) wl_run_escan : scan error (-37)
[   70.456423] [dhd] CFG80211-ERROR) wl_cfg80211_scan : scan error (-11)
[   80.463709] [dhd-wlan0] wl_run_escan : LEGACY_SCAN sync ID: 8, bssidx: 0
[   80.464212] [dhd] CFG80211-ERROR) wl_run_escan :  Escan set error (-37)
[   80.464233] [dhd] CFG80211-ERROR) wl_run_escan : scan error (-37)
[   80.464256] [dhd] CFG80211-ERROR) wl_cfg80211_scan : scan error (-11)

大神们,帮忙看下是什么问题?
回复

使用道具 举报

1万

积分

18

威望

20

贡献

神级创客

Rank: 8Rank: 8

积分
10851

突出贡献

发表于 2021-9-9 15:42:51        只看该作者  沙发
请问具体是哪一个板型,ROC-RK3568-PC?烧写的固件是哪一个
回复

使用道具 举报

32

积分

0

威望

0

贡献

技术小白

积分
32
发表于 2021-9-9 16:00:04        只看该作者  板凳
zyk 发表于 2021-9-9 15:42
请问具体是哪一个板型,ROC-RK3568-PC?烧写的固件是哪一个

TB-RK3568X,固件是从ROCKCHIP_ANDROID11.0_SDK编译出来的
回复

使用道具 举报

1万

积分

18

威望

20

贡献

神级创客

Rank: 8Rank: 8

积分
10851

突出贡献

发表于 2021-9-9 16:36:58        只看该作者  地板
没调过TB-RK3568X
回复

使用道具 举报

32

积分

0

威望

0

贡献

技术小白

积分
32
发表于 2021-9-10 17:36:53        只看该作者  5#
zyk 发表于 2021-9-9 16:36
没调过TB-RK3568X

好吧,是驱动版本的问题,我下载了最新的sdk,扫描不再报错,也能扫描到热点,但是无法连接到热点,这种问题有遇到过吗?
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

友情链接 : 爱板网 电子发烧友论坛 云汉电子社区 粤ICP备14022046号-2
快速回复 返回顶部 返回列表