android pad 烧写后系统起不来

zhutousame

android pad 烧写后系统起不来
1.安装官网链接 http://wiki.t-firefly.com/index.php/Firefly-RK3288/Build_android，编译了pad版本的android，我更新到最新版的代码（git pull bitbucket pad:pad），编译正式版(0930)开发板的内核，将生成的img拷出来烧写的时候发现系统起不来。
2.经过测试发现了三个问题：
  A.第一个问题单独烧写misc.img固件，导致系统进入recovery，串口如下：

1. DDR Version 1.00 20141007
   
2. In
   
3. SRX
   
4. Channel a: DDR3 200MHz
   
5. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
   
6. Channel b: DDR3 200MHz
   
7. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
   
8. OUT
   
9. 
   
10. 
    
11. U-Boot 2014.10-RK3288-01 (Nov 27 2014 - 16:44:27)
    
12. 
    
13. CPU: rk3288
    
14. CPU's clock information:
    
15.     arm pll = 600000000HZ
    
16.     periph pll = 297000000HZ
    
17.     ddr pll = 200000000HZ
    
18.     codec pll = 384000000HZ
    
19. Board:  Rockchip platform Board
    
20. DRAM:  Found dram banks:1
    
21. Adding bank:0000000000000000(0000000080000000)
    
22. 128 MiB
    
23. storage init OK!
    
24. Using default environment
    
25. 
    
26. GetParam
    
27. check parameter success
    
28. Unknow param: MACHINE_MODEL:rk30sdk!
    
29. Unknow param: MACHINE_ID:007!
    
30. Unknow param: MANUFACTURER:RK30SDK!
    
31. Unknow param: PWR_HLD: 0,0,A,0,1!
    
32. failed to prepare fdt from boot!
    
33. power key: bank-0 pin-5
    
34. pmic:act8846
    
35. SecureBootEn = 0, SecureBootLock = 0
    
36. 
    
37. #Boot ver: 2014-11-27#2.19
    
38. sn:100612000000019D
    
39. checkKey
    
40. vbus = 1
    
41. no fuel gauge found
    
42. no fuel gauge found
    
43. read logo_on switch from dts [0]
    
44. no fuel gauge found
    
45. got recovery cmd from misc.
    
46. failed to load fdt from recovery!
    
47. kernel   @ 0x02000000 (0x00659f60)
    
48. ramdisk  @ 0x04bf0000 (0x003d1840)
    
49. Secure Boot state: 0
    
50. bootrk: do_bootm_linux...
    
51.    Loading Device Tree to 0480d000, end 0482aaf9 ... OK
    
52. Add bank:0000000000000000, 0000000080000000
    
53. 
    
54. Starting kernel ...
    
55. 
    
56. <hit enter to activate fiq debugger>
    
57. [    0.000000] Booting Linux on physical CPU 0x500
    
58. [    0.000000] Initializing cgroup subsys cpu
    
59. [    0.000000] Initializing cgroup subsys cpuacct
    
60. [    0.000000] Linux version 3.10.0 (firefly@midserver) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #3 SMP PREEMPT Tue Dec         30 15:45:08 CST 2014
    
61. [    0.000000] CPU: ARMv7 Processor [410fc0d1] revision 1 (ARMv7), cr=10c5387d
    
62. [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
    
63. [    0.000000] Machine: Rockchip RK3288 (Flattened Device Tree), model: rockchip,rk3288
    
64. [    0.000000] rockchip_ion_reserve
    
65. [    0.000000] ion heap(cma): base(40000000) size(28000000) align(0)
    
66. [    0.000000] ion heap(vmalloc): base(0) size(0) align(0)
    
67. [    0.000000] cma: CMA: reserved 640 MiB at 40000000
    
68. [    0.000000] ion_reserve: cma reserved base 40000000 size 671088640
    
69. [    0.000000] cma: CMA: reserved 16 MiB at 2e800000
    
70. [    0.000000] Memory policy: ECC disabled, Data cache writealloc
    
71. [    0.000000] Boot mode: RECOVERY (2) flag: RECOVER (0xc3524203)
    
72. [    0.000000] PERCPU: Embedded 9 pages/cpu @c1dea000 s14016 r8192 d14656 u36864
    
73. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 522768
    
74. [    0.000000] Kernel command line: console=ttyFIQ0 androidboot.hardware=rk30board androidboot.console=ttyFIQ0 board.ap_has_alsa=0 init        =/init  mtdparts=rk29xxnand:0x00002000@0x00000000(parameter),0x00002000@0x00002000(uboot),0x00002000@0x00004000(misc),0x00008000@0x0000        6000(resource),0x00008000@0x0000e000(kernel),0x00010000@0x00016000(boot),0x00010000@0x00026000(recovery),0x0001a000@0x00036000(backup),        0x00040000@0x00050000(cache),0x00002000@0x00090000(kpanic),0x00180000@0x00092000(system),0x00002000@0x00212000(metadata),0x00200000@0x0        0214000(userdata),0x00020000@0x00414000(radical_update),-@0x00434000(user) storagemedia=emmc loader.timestamp=2014-11-27_16:44:27 andro        idboot.serialno=100612000000019D
    
75. [    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
    
76. [    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    
77. [    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    
78. [    0.000000] allocated 4194304 bytes of page_cgroup
    
79. [    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    
80. [    0.000000] Memory: 2048MB = 2048MB total
    
81. [    0.000000] Memory: 1385680k/1385680k available, 711472k reserved, 663552K highmem
    
82. [    0.000000] Virtual kernel memory layout:
    
83. [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    
84. [    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    
85. [    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
    
86. [    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
    
87. [    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    
88. [    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
    
89. [    0.000000]       .text : 0xc0008000 - 0xc0af04ac   (11170 kB)
    
90. [    0.000000]       .init : 0xc0af1000 - 0xc0b856c0   ( 594 kB)
    
91. [    0.000000]       .data : 0xc0b86000 - 0xc0c8e9b8   (1059 kB)
    
92. [    0.000000]        .bss : 0xc0c8e9b8 - 0xc0daca04   (1145 kB)
    
93. [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
    
94. [    0.000000] Preemptible hierarchical RCU implementation.
    
95. [    0.000000]  RCU dyntick-idle grace-period acceleration is enabled.
    
96. [    0.000000] NR_IRQS:16 nr_irqs:16 16
    
97. [    0.000000] rk_clk_tree_init start! cru base = 0xfed00000
    
98. [    0.000000] rk_get_uboot_display_flag: uboot_logo_on = 0
    
99. [    0.000000] rkclk_init_clks: cnt_parent = 7
    
100. [    0.000000] rkclk_init_clks: cnt_rate = 31
     
101. [    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
     
102. [    0.000000] Switching to timer-based delay loop
     
103. [    0.000000] sched_clock: ARM arch timer >56 bits at 24000kHz, resolution 41ns
     
104. [    0.000000] process version: 1
     
105. [    0.000000] channel:0, lkg:55
     
106. [    0.000000] target-temp:80
     
107. [    0.000000] channel:2, lkg:0
     
108. [    0.000000] target-temp:80
     
109. [    0.000000] channel:0, lkg:55
     
110. [    0.000000] target-temp:80
     
111. [    0.000000] channel:1, lkg:58
     
112. [    0.000000] target-temp:80
     
113. [    0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
     
114. [    0.304981] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
     
115. [    0.304996] pid_max: default: 32768 minimum: 301
     
116. [    0.305100] Security Framework initialized
     
117. [    0.305118] SELinux:  Initializing.
     
118. [    0.305189] Mount-cache hash table entries: 512
     
119. [    0.305826] Initializing cgroup subsys debug
     
120. [    0.305840] Initializing cgroup subsys memory
     
121. [    0.305867] Initializing cgroup subsys freezer
     
122. [    0.305896] CPU: Testing write buffer coherency: ok
     
123. [    0.306205] /cpus/cpu@0 missing clock-frequency property
     
124. [    0.306218] /cpus/cpu@1 missing clock-frequency property
     
125. [    0.306228] /cpus/cpu@2 missing clock-frequency property
     
126. [    0.306237] /cpus/cpu@3 missing clock-frequency property
     
127. [    0.306298] CPU0: thread -1, cpu 0, socket 5, mpidr 80000500
     
128. [    0.306348] Setting up static identity map for 0xc07df1a8 - 0xc07df200
     
129. [    0.309425] last_log: 0x2e100000 map to 0xf0004000 and copy to 0xf0086000, size 0x80000 early 0x16e1 (version 3.0)
     
130. [    0.383098] CPU1: Booted secondary processor
     
131. [    0.383132] CPU1: thread -1, cpu 1, socket 5, mpidr 80000501
     
132. [    0.402781] CPU2: Booted secondary processor
     
133. [    0.402806] CPU2: thread -1, cpu 2, socket 5, mpidr 80000502
     
134. [    0.422493] CPU3: Booted secondary processor
     
135. [    0.422516] CPU3: thread -1, cpu 3, socket 5, mpidr 80000503
     
136. [    0.422617] Brought up 4 CPUs
     
137. [    0.422645] SMP: Total of 4 processors activated (192.00 BogoMIPS).
     
138. [    0.422653] CPU: All CPU(s) started in SVC mode.
     
139. [    0.423368] devtmpfs: initialized
     
140. [    0.428318] pinctrl core: initialized pinctrl subsystem
     
141. [    0.428567] regulator-dummy: no parameters
     
142. [    0.439938] NET: Registered protocol family 16
     
143. [    0.441736] DMA: preallocated 256 KiB pool for atomic coherent allocations
     
144. [    0.442085] ion_snapshot: 0x2e248000 map to 0xf0107000 and copy to 0xc0d88004 (version 0.1)
     
145. [    0.442448] Registered FIQ tty driver
     
146. [    0.443789] console [ttyFIQ0] enabled
     
147. [    0.443974] Registered fiq debugger ttyFIQ0
     
148. [    0.444546] rockchip_get_bank_data:name=base start=0xff750000,end=0xff7500ff
     
149. [    0.444570] rockchip_get_bank_data:name=mux_bank0 start=0xff730084,end=0xff73008f
     
150. [    0.444589] rockchip_get_bank_data:name=pull_bank0 start=0xff730064,end=0xff73006f
     
151. [    0.444608] rockchip_get_bank_data:name=drv_bank0 start=0xff730070,end=0xff73007b
     
152. [    0.444706] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio1@ff780000 start=0xff780000,end=0xff7800ff
     
153. [    0.444773] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio2@ff790000 start=0xff790000,end=0xff7900ff
     
154. [    0.444838] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio3@ff7a0000 start=0xff7a0000,end=0xff7a00ff
     
155. [    0.444901] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio4@ff7b0000 start=0xff7b0000,end=0xff7b00ff
     
156. [    0.444965] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio5@ff7c0000 start=0xff7c0000,end=0xff7c00ff
     
157. [    0.445029] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio6@ff7d0000 start=0xff7d0000,end=0xff7d00ff
     
158. [    0.445094] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio7@ff7e0000 start=0xff7e0000,end=0xff7e00ff
     
159. [    0.445159] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio8@ff7f0000 start=0xff7f0000,end=0xff7f00ff
     
160. [    0.445229] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio15@ff7f2000 start=0xff7f2000,end=0xff7f20ff
     
161. [    0.445296] rockchip_pinctrl_probe:name=RK3288-GPIO,type=3
     
162. [    0.445312] rockchip_pinctrl_probe:name=base start=0xff770000,end=0xff77013f
     
163. [    0.445327] rockchip_pinctrl_probe:name=pull start=0xff770140,end=0xff7701bf
     
164. [    0.445341] rockchip_pinctrl_probe:name=drv start=0xff7701c0,end=0xff77023f
     
165. [    0.445850] rockchip_interrupts_register:bank_num=7
     
166. [    0.447772] rockchip_pinctrl_probe:init ok
     
167. [    0.453736] rk_iommu ff900800.iep_mmu: (iep) Enter
     
168. [    0.453829] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
     
169. [    0.453846] rk_iommu ff900800.iep_mmu: (iep) Initialized
     
170. [    0.454018] rk_iommu ff950800.vip_mmu: (vip) Enter
     
171. [    0.454090] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
     
172. [    0.454105] rk_iommu ff950800.vip_mmu: (vip) Initialized
     
173. [    0.454263] rk_iommu ff930300.vopb_mmu: (vopb) Enter
     
174. [    0.454336] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
     
175. [    0.454351] rk_iommu ff930300.vopb_mmu: (vopb) Initialized
     
176. [    0.454515] rk_iommu ff940300.vopl_mmu: (vopl) Enter
     
177. [    0.454587] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
     
178. [    0.454602] rk_iommu ff940300.vopl_mmu: (vopl) Initialized
     
179. [    0.454765] rk_iommu ff9c0440.hevc_mmu: (hevc) Enter
     
180. [    0.454842] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
     
181. [    0.454858] rk_iommu ff9c0440.hevc_mmu: (hevc) Initialized
     
182. [    0.455021] rk_iommu ff9a0800.vpu_mmu: (vpu) Enter
     
183. [    0.455093] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
     
184. [    0.455108] rk_iommu ff9a0800.vpu_mmu: (vpu) Initialized
     
185. [    0.455287] rk_iommu ff914000.isp_mmu: (isp_mmu) Enter
     
186. [    0.455360] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
     
187. [    0.455375] rk_iommu ff914000.isp_mmu: (isp_mmu) Initialized
     
188. [    0.457067] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
     
189. [    0.457084] hw-breakpoint: maximum watchpoint size is 4 bytes.
     
190. [    0.457292] DDR DEBUG: version 1.00 20140603
     
191. [    0.457323] DDR DEBUG: Channel a:
     
192. [    0.457333] DDR DEBUG: DDR3 Device
     
193. [    0.457348] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Total Capability=1024MB
     
194. [    0.457360] DDR DEBUG: Channel b:
     
195. [    0.457369] DDR DEBUG: DDR3 Device
     
196. [    0.457383] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Total Capability=1024MB
     
197. [    0.457395] DDR DEBUG: addr=0xc96000
     
198. [    0.457407] DDR DEBUG: stride=9, size=256, halfcap=40000000
     
199. [    0.457418] DDR DEBUG: socAddr[0]=0xc96000, socAddr[1]=0xc96100
     
200. [    0.457430] DDR DEBUG: chAddr[0]=0xc96000, chAddr[1]=0xc96000
     
201. [    0.457443] DDR DEBUG: dtar[0]=0x60192000, dtar[1]=0x60192000
     
202. [    0.457690] DDR DEBUG: init success!!! freq=300MHz
     
203. [    0.457700] DDR DEBUG: Channel a:
     
204. [    0.457714] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
     
205. [    0.457730] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
     
206. [    0.457748] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
     
207. [    0.457764] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
     
208. [    0.457779] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0
     
209. [    0.457792] DDR DEBUG: DRV Pull-Up=0x19, DRV Pull-Dwn=0x19
     
210. [    0.457802] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2
     
211. [    0.457812] DDR DEBUG: Channel b:
     
212. [    0.457825] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
     
213. [    0.457841] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
     
214. [    0.457857] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
     
215. [    0.457873] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=270,270
     
216. [    0.457887] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0
     
217. [    0.457899] DDR DEBUG: DRV Pull-Up=0x19, DRV Pull-Dwn=0x19
     
218. [    0.457910] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2
     
219. [    0.480004] bio: create slab <bio-0> at 0
     
220. [    0.480823] SCSI subsystem initialized
     
221. [    0.480973] usbcore: registered new interface driver usbfs
     
222. [    0.481019] usbcore: registered new interface driver hub
     
223. [    0.481101] usbcore: registered new device driver usb
     
224. [    0.482478] rockchip_i2c ff650000.i2c: i2c-0: Rockchip I2C adapter
     
225. [    0.484665] rockchip_i2c ff140000.i2c: i2c-1: Rockchip I2C adapter
     
226. [    0.486171] rockchip_i2c ff660000.i2c: i2c-2: Rockchip I2C adapter
     
227. [    0.487155] rockchip_i2c ff150000.i2c: i2c-3: Rockchip I2C adapter
     
228. [    0.487394] rockchip_i2c ff160000.i2c: i2c-4: Rockchip I2C adapter
     
229. [    0.487871] media: Linux media interface: v0.10
     
230. [    0.487913] Linux video capture interface: v2.00
     
231. [    0.487967] pps_core: LinuxPPS API ver. 1 registered
     
232. [    0.487979] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
     
233. [    0.488003] PTP clock support registered
     
234. [    0.488499] Rockchip ion module is successfully loaded (v1.0)
     
235. [    0.488661] Advanced Linux Sound Architecture Driver Initialized.
     
236. [    0.489032] Bluetooth: Core ver 2.16
     
237. [    0.489071] NET: Registered protocol family 31
     
238. [    0.489082] Bluetooth: HCI device and connection manager initialized
     
239. [    0.489100] Bluetooth: HCI socket layer initialized
     
240. [    0.489115] Bluetooth: L2CAP socket layer initialized
     
241. [    0.489141] Bluetooth: SCO socket layer initialized
     
242. [    0.489370] cfg80211: Calling CRDA to update world regulatory domain
     
243. [    0.490023] act8846_i2c_probe,line=898
     
244. [    0.490983] act8846_parse_dt,line=746
     
245. [    0.491718] act8846_i2c_probe: act8846_pmic_hold=1
     
246. [    0.491740] act8846_i2c_probe: act8846_pmic_sleep=1
     
247. [    0.491758] act8846_i2c_probe: act8846_pmic_cpu_det_gpio=1
     
248. [    0.491774] act8846_i2c_probe: act8846_pmic_usb_hub_reset_gpio=1
     
249. [    0.493599] act_dcdc1: 1200 mV
     
250. [    0.496320] vccio: 3300 mV
     
251. [    0.498168] vdd_logic: 700 <--> 1500 mV at 1100 mV
     
252. [    0.500904] act_dcdc4: 2000 mV
     
253. [    0.502132] vccio_sd: 1800 <--> 3300 mV at 3300 mV
     
254. [    0.504206] act_ldo2: 1000 mV
     
255. [    0.506284] act_ldo3: 3300 mV
     
256. [    0.508359] act_ldo4: 3300 mV
     
257. [    0.510450] act_ldo5: 3300 mV
     
258. [    0.512575] act_ldo6: 1000 mV
     
259. [    0.514648] vcc_18: 1800 mV
     
260. [    0.516715] act_ldo8: 1800 mV
     
261. [    0.521483] vdd_arm: 712 <--> 1500 mV at 1000 mV
     
262. [    0.526193] vdd_gpu: 712 <--> 1500 mV at 1000 mV
     
263. [    0.526988] Switching to clocksource arch_sys_counter
     
264. [    0.546804] rk-fb rockchip-fb: rk fb ion client create success!
     
265. [    0.546822] rk-fb rockchip-fb: rockchip framebuffer driver probe
     
266. [    0.547212] rk-screen rk_screen.9: rockchip screen probe success
     
267. [    0.547464] rk32-lvds rk32-lvds: rk32 lvds driver probe success
     
268. [    0.547791] rk32-edp ff970000.edp: screen is not edp!
     
269. [    0.547813] rk32-edp: probe of ff970000.edp failed with error -22
     
270. [    0.548524] graphics fb0: rockchip framebuffer registerd:fb0
     
271. [    0.548844] graphics fb1: rockchip framebuffer registerd:fb1
     
272. [    0.549001] graphics fb2: rockchip framebuffer registerd:fb2
     
273. [    0.549159] graphics fb3: rockchip framebuffer registerd:fb3
     
274. [    0.569511] rk3288-lcdc lcdc0: lcdc0: dclk:78000000>>fps:68
     
275. [    0.569536] rk3288-lcdc lcdc0: wakeup from standby!
     
276. [    0.585438] alloc_buffer:ion_phy_addr=0x40000000
     
277. [    0.588424] rk_battery_charger_detect_cb , battery_charger_detect 1
     
278. [    0.593798] fb0:phy:40000000>>vir:f0171000>>len:0xc00000
     
279. [    0.597327] rk3288-lcdc lcdc0: lcdc0 probe ok, iommu disabled
     
280. [    0.597482] rk3288-lcdc lcdc1: can't find power_ctr node for lcdc1
     
281. [    0.597497] rk_fb_trsm_ops_get:un supported transmitter:0!
     
282. [    0.597726] graphics fb4: rockchip framebuffer registerd:fb4
     
283. [    0.598029] graphics fb5: rockchip framebuffer registerd:fb5
     
284. [    0.598188] graphics fb6: rockchip framebuffer registerd:fb6
     
285. [    0.598343] graphics fb7: rockchip framebuffer registerd:fb7
     
286. [    0.598360] fb0:phy:40000000>>vir:f0171000>>len:0xc00000
     
287. [    0.598374] rk3288-lcdc lcdc1: lcdc1 probe ok, iommu disabled
     
288. [    0.598954] rockchip_set_mux:warning ignore bank num 15
     
289. [    0.599073] rockchip_set_mux:warning ignore bank num 15
     
290. [    0.599183] rockchip_set_mux:warning ignore bank num 15
     
291. [    0.599291] rockchip_set_mux:warning ignore bank num 15
     
292. [    0.599394] rockchip_set_mux:warning ignore bank num 15
     
293. [    0.599505] rockchip_set_mux:warning ignore bank num 15
     
294. [    0.600063] rockchip_set_mux:warning ignore bank num 15
     
295. [    0.600202] rockchip_set_mux:warning ignore bank num 15
     
296. [    0.600740] rockchip_set_mux:warning ignore bank num 15
     
297. [    0.600882] rockchip_set_mux:warning ignore bank num 15
     
298. [    0.601417] rockchip_set_mux:warning ignore bank num 15
     
299. [    0.601555] rockchip_set_mux:warning ignore bank num 15
     
300. [    0.602104] rockchip_set_mux:warning ignore bank num 15
     
301. [    0.602247] rockchip_set_mux:warning ignore bank num 15
     
302. [    0.603544] NET: Registered protocol family 2
     
303. [    0.603982] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
     
304. [    0.604117] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
     
305. [    0.604253] TCP: Hash tables configured (established 8192 bind 8192)
     
306. [    0.604301] TCP: reno registered
     
307. [    0.604318] UDP hash table entries: 512 (order: 2, 16384 bytes)
     
308. [    0.604355] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
     
309. [    0.604554] NET: Registered protocol family 1
     
310. [    0.604732] Unpacking initramfs...
     
311. [    0.766538] Freeing initrd memory: 3908K (c4bf0000 - c4fc1000)
     
312. [    0.767149] hw perfevents: enabled with ARMv7 Cortex-A12 PMU driver, 7 counters available
     
313. [    0.767607] probe device ff9a0000.vpu_service
     
314. [    0.767783] vpu_service: power on
     
315. [    0.768841] checking hw id 4831
     
316. [    0.769229] vpu_service set to auto frequency mode
     
317. [    0.769267] vpu_service: power off...
     
318. [    0.769306] done
     
319. [    0.769315] init success
     
320. [    0.769379] probe device ff9c0000.hevc_service
     
321. [    0.769573] hevc_service: power on
     
322. [    0.770610] checking hw id 6867
     
323. [    0.770836] hevc_service: power off...
     
324. [    0.770875] done
     
325. [    0.770884] init success
     
326. [    0.770995] rknandbase v1.0 2014-03-31
     
327. [    0.771091] rknand ff400000.nandc0: no irq resource?
     
328. [    0.771209] rknand_driver:ret = 0
     
329. [    0.772724] audit: initializing netlink socket (disabled)
     
330. [    0.772765] type=2000 audit(0.460:1): initialized
     
331. [    0.773576] bounce pool size: 64 pages
     
332. [    0.777914] fuse init (API version 7.22)
     
333. [    0.778255] msgmni has been set to 1450
     
334. [    0.779984] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
     
335. [    0.780004] io scheduler noop registered
     
336. [    0.780015] io scheduler deadline registered
     
337. [    0.780105] io scheduler cfq registered (default)
     
338. [    0.783632] rga2 ff920000.rga: rga ion client create success!
     
339. [    0.783775] rga: Driver loaded succesfully
     
340. [    0.784377] IEP Driver loaded succesfully
     
341. [    0.784466] Module initialized.
     
342. [    0.785332] dma-pl330 ffb20000.pdma: Loaded driver for PL330 DMAC-2364208
     
343. [    0.785354] dma-pl330 ffb20000.pdma:         DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10
     
344. [    0.786636] dma-pl330 ff250000.pdma: Loaded driver for PL330 DMAC-2364208
     
345. [    0.786656] dma-pl330 ff250000.pdma:         DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
     
346. [    0.786935] pwm-voltage-regulator pwm_regulator.25: unable to request PWM, trying legacy API
     
347. [    0.786954] pwm-voltage-regulator pwm_regulator.25: unable to request legacy PWM
     
348. [    0.786967] pwm_regulator_probe:error
     
349. [    0.786991] platform pwm_regulator.25: Driver pwm-voltage-regulator requests probe deferral
     
350. [    0.787318] rk_serial.c v1.8 2014-03-04
     
351. [    0.787524] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 87) is a rk29_serial.0
     
352. [    0.787711] serial ff180000.serial: membase f0d94000
     
353. [    0.790361] loop: module loaded
     
354. [    0.790906] SCSI Media Changer driver v0.25
     
355. [    0.791203] tun: Universal TUN/TAP device driver, 1.6
     
356. [    0.791218] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
     
357. [    0.791367] vmac_init.
     
358. [    0.791861] stmmac_probe_config_dt: Can not read property: pmu_regulator.
     
359. [    0.791878] stmmac_probe_config_dt: Can not read property: pmu_enable_level.
     
360. [    0.791892] stmmac_probe_config_dt: clock input or output? (input).
     
361. [    0.791905] stmmac_probe_config_dt: TX delay(0x30).
     
362. [    0.791916] stmmac_probe_config_dt: RX delay(0x10).
     
363. [    0.791963] stmmac_probe_config_dt: is rockchip,rk3288-gmac
     
364. [    0.791974] stmmc_pltfr_init:
     
365. [    0.791994] stmmc_pltfr_init: init for RGMII
     
366. [    0.792006] tx delay=0x30
     
367. [    0.792006] rx delay=0x10
     
368. [    0.792438] stmmac - user ID: 0x10, Synopsys ID: 0x35
     
369. [    0.792450]  Normal descriptors
     
370. [    0.792458]  Ring mode enabled
     
371. [    0.792468]  DMA HW capability register supported
     
372. [    0.792480]  RX Checksum Offload Engine supported (type 2)
     
373. [    0.792491]  TX Checksum insertion supported
     
374. [    0.792500]  Wake-Up On Lan supported
     
375. [    0.792535]  Enable RX Mitigation via HW Watchdog Timer
     
376. [    0.792963] PPP generic driver version 2.4.2
     
377. [    0.793114] PPP BSD Compression module registered
     
378. [    0.793128] PPP Deflate Compression module registered
     
379. [    0.793151] PPP MPPE Compression module registered
     
380. [    0.793163] NET: Registered protocol family 24
     
381. [    0.793196] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
     
382. [    0.793210] CSLIP: code copyright 1989 Regents of the University of California.
     
383. [    0.793229] Rockchip WiFi SYS interface (V1.00) ...
     
384. [    0.793261] esp_mem_init enter date Dec 26 2014 09:48:50
     
385. [    0.793303] esp_mem_init complete
     
386. [    0.793371] usbcore: registered new interface driver catc
     
387. [    0.793411] usbcore: registered new interface driver kaweth
     
388. [    0.793424] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
     
389. [    0.793463] usbcore: registered new interface driver pegasus
     
390. [    0.793503] usbcore: registered new interface driver rtl8150
     
391. [    0.793542] usbcore: registered new interface driver r8152
     
392. [    0.793553] hso: drivers/net/usb/hso.c: Option Wireless
     
393. [    0.793618] usbcore: registered new interface driver hso
     
394. [    0.793663] usbcore: registered new interface driver asix
     
395. [    0.793701] usbcore: registered new interface driver ax88179_178a
     
396. [    0.793739] usbcore: registered new interface driver cdc_ether
     
397. [    0.793788] usbcore: registered new interface driver cdc_eem
     
398. [    0.793826] usbcore: registered new interface driver dm9601
     
399. [    0.793864] usbcore: registered new interface driver dm9620
     
400. [    0.793910] usbcore: registered new interface driver smsc75xx
     
401. [    0.793956] usbcore: registered new interface driver smsc95xx
     
402. [    0.793994] usbcore: registered new interface driver gl620a
     
403. [    0.794036] usbcore: registered new interface driver net1080
     
404. [    0.794076] usbcore: registered new interface driver plusb
     
405. [    0.794115] usbcore: registered new interface driver rndis_host
     
406. [    0.794153] usbcore: registered new interface driver cdc_subset
     
407. [    0.794190] usbcore: registered new interface driver zaurus
     
408. [    0.794230] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
     
409. [    0.794286] usbcore: registered new interface driver int51x1
     
410. [    0.794325] usbcore: registered new interface driver kalmia
     
411. [    0.794368] usbcore: registered new interface driver ipheth
     
412. [    0.794410] usbcore: registered new interface driver sierra_net
     
413. [    0.794450] usbcore: registered new interface driver cx82310_eth
     
414. [    0.794498] usbcore: registered new interface driver cdc_ncm
     
415. [    0.794537] usbcore: registered new interface driver qmi_wwan
     
416. [    0.794576] usbcore: registered new interface driver cdc_mbim
     
417. [    0.794589] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
     
418. [    0.796972] ehci_rk_probe f0e00000 f0e00010
     
419. [    0.796990] rockchip_ehci_host ff500000.usb: Rockchip On-Chip EHCI Host Controller
     
420. [    0.797021] rockchip_ehci_host ff500000.usb: new USB bus registered, assigned bus number 1
     
421. [    0.797332] rockchip_ehci_host ff500000.usb: irq 56, io mem 0xff500000
     
422. [    0.812423] rockchip_ehci_host ff500000.usb: USB 0.0 started, EHCI 1.00
     
423. [    0.812497] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
     
424. [    0.812515] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
     
425. [    0.812530] usb usb1: Product: Rockchip On-Chip EHCI Host Controller
     
426. [    0.812544] usb usb1: Manufacturer: Linux 3.10.0 ehci_hcd
     
427. [    0.812557] usb usb1: SerialNumber: ff500000.usb
     
428. [    0.812968] hub 1-0:1.0: USB hub found
     
429. [    0.812992] hub 1-0:1.0: 1 port detected
     
430. [    0.841930] ehci_rk_probe ok
     
431. [    0.842087] usbcore: registered new interface driver cdc_acm
     
432. [    0.842101] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
     
433. [    0.842156] usbcore: registered new interface driver usblp
     
434. [    0.842204] usbcore: registered new interface driver cdc_wdm
     
435. [    0.842266] usbcore: registered new interface driver usb-storage
     
436. [    0.842308] usbcore: registered new interface driver ums-alauda
     
437. [    0.842346] usbcore: registered new interface driver ums-cypress
     
438. [    0.842385] usbcore: registered new interface driver ums-datafab
     
439. [    0.842421] usbcore: registered new interface driver ums_eneub6250
     
440. [    0.842460] usbcore: registered new interface driver ums-freecom
     
441. [    0.842498] usbcore: registered new interface driver ums-isd200
     
442. [    0.842537] usbcore: registered new interface driver ums-jumpshot
     
443. [    0.842580] usbcore: registered new interface driver ums-karma
     
444. [    0.842620] usbcore: registered new interface driver ums-onetouch
     
445. [    0.842660] usbcore: registered new interface driver ums-sddr09
     
446. [    0.842708] usbcore: registered new interface driver ums-sddr55
     
447. [    0.842748] usbcore: registered new interface driver ums-usbat
     
448. [    0.842830] usbcore: registered new interface driver usbserial
     
449. [    0.842868] usbcore: registered new interface driver usbserial_generic
     
450. [    0.842899] usbserial: USB Serial support registered for generic
     
451. [    0.842941] usbcore: registered new interface driver option
     
452. [    0.842971] usbserial: USB Serial support registered for GSM modem (1-port)
     
453. [    0.843063] usbcore: registered new interface driver trancevibrator
     
454. [    0.843075] usb20_otg: version 3.10a 21-DEC-2012
     
455. [    0.843478] f0e80040
     
456. [    0.843492] Core Release: 3.10a
     
457. [    0.843504] Setting default values for core params
     
458. [    0.843618] Using Buffer DMA mode
     
459. [    0.843630] Periodic Transfer Interrupt Enhancement - disabled
     
460. [    0.843641] Multiprocessor Interrupt Enhancement - disabled
     
461. [    0.843654] OTG VER PARAM: 0, OTG VER FLAG: 0
     
462. [    0.843664] ^^^^^^^^^^^^^^^^^Device Mode
     
463. [    0.843678] Dedicated Tx FIFOs mode
     
464. [    0.843695] pcd_init otg_dev = ed6a7640
     
465. [    0.843830] usb20_otg ff580000.usb: DWC OTG Controller
     
466. [    0.843857] usb20_otg ff580000.usb: new USB bus registered, assigned bus number 2
     
467. [    0.843887] usb20_otg ff580000.usb: irq 55, io mem 0x00000000
     
468. [    0.843940] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
     
469. [    0.843956] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
     
470. [    0.843971] usb usb2: Product: DWC OTG Controller
     
471. [    0.843991] usb usb2: Manufacturer: Linux 3.10.0 dwc_otg_hcd
     
472. [    0.844005] usb usb2: SerialNumber: ff580000.usb
     
473. [    0.844365] hub 2-0:1.0: USB hub found
     
474. [    0.844388] hub 2-0:1.0: 1 port detected
     
475. [    0.844685] usb20_host: version 3.10a 21-DEC-2012
     
476. [    0.847146] f0f00040
     
477. [    0.847159] Core Release: 3.10a
     
478. [    0.847170] Setting default values for core params
     
479. [    0.847263] Using Buffer DMA mode
     
480. [    0.847275] Periodic Transfer Interrupt Enhancement - disabled
     
481. [    0.847286] Multiprocessor Interrupt Enhancement - disabled
     
482. [    0.847298] OTG VER PARAM: 0, OTG VER FLAG: 0
     
483. [    0.847308] ^^^^^^^^^^^^^^^^^^Host Mode
     
484. [    0.847336] usb20_host ff540000.usb: DWC OTG Controller
     
485. [    0.847362] usb20_host ff540000.usb: new USB bus registered, assigned bus number 3
     
486. [    0.847390] usb20_host ff540000.usb: irq 57, io mem 0x00000000
     
487. [    0.847482] Init: Power Port (0)
     
488. [    0.847536] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
     
489. [    0.847552] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
     
490. [    0.847567] usb usb3: Product: DWC OTG Controller
     
491. [    0.847579] usb usb3: Manufacturer: Linux 3.10.0 dwc_otg_hcd
     
492. [    0.847592] usb usb3: SerialNumber: ff540000.usb
     
493. [    0.847947] hub 3-0:1.0: USB hub found
     
494. [    0.847969] hub 3-0:1.0: 1 port detected
     
495. [    0.848473] .. rk pwm remotectl v1.0 init
     
496. [    0.848555] remotectl probe j=0x0
     
497. [    0.848699] input: ff680000.pwm as /devices/ff680000.pwm/input/input0
     
498. [    0.848873] pwm enable val=0x646205
     
499. [    0.849131] usbcore: registered new interface driver xpad
     
500. [    0.849184] usbcore: registered new interface driver usb_acecad
     
501. [    0.849228] usbcore: registered new interface driver aiptek
     
502. [    0.849272] usbcore: registered new interface driver gtco
     
503. [    0.849316] usbcore: registered new interface driver hanwang
     
504. [    0.849359] usbcore: registered new interface driver kbtab
     
505. [    0.849413] usbcore: registered new interface driver wacom
     
506. [    0.849424] ==gsl_ts_init==
     
507. [    0.849494] GSLX680 Enter gsl_ts_probe
     
508. [    0.849505] ==kzalloc success=
     
509. [    0.849515] gsl_ts_probe-1292
     
510. [    0.849553] gslX680 1-0041: reset pin invalid
     
511. [    0.849564] [GSLX680] Enter gslX680_ts_init
     
512. [    0.849784] input: gslX680 as /devices/ff140000.i2c/i2c-1/1-0041/input/input1
     
513. [    0.849909] gsl_ts_probe-1318
     
514. [    0.849921] org chip_type=36
     
515. [    0.901668] gsl_ts_read set data address fail! ret=-11-0xfffffff5
     
516. [    0.940381] dwc_otg_hcd_suspend, usb device mode
     
517. [    0.960689] gsl_ts_read set data address fail! ret=-11-0xfffffff5
     
518. [    0.960703] chip_type=88, reg=0
     
519. [    1.019045] test_i2c-394: Enter
     
520. [    1.019729] gsl_ts_read set data address fail! ret=-11-0xfffffff5
     
521. [    1.059079] gsl_ts_read set data address fail! ret=-11-0xfffffff5
     
522. [    1.059093] test_i2c-413: Exit
     
523. [    1.059102] ------gslX680 test_i2c error------
     
524. [    1.098436] gsl_ts_read set data address fail! ret=-11-0xfffffff5
     
525. [    1.098450] #########check mem read 0xb0 = 0 0 0 0 #########
     
526. [    1.156804] test_i2c-394: Enter
     
527. [    1.157485] gsl_ts_read set data address fail! ret=-11-0xfffffff5
     
528. [    1.196833] gsl_ts_read set data address fail! ret=-11-0xfffffff5
     
529. [    1.196846] test_i2c-413: Exit
     
530. [    1.196855] ------gslX680 test_i2c error------
     
531. [    1.197028] gsl_ts_probe () : queue gsl_monitor_workqueue
     
532. [    1.197109] [GSLX680] End gsl_ts_probe
     
533. [    1.197178] ret=0
     
534. [    1.202053] rtc_hym8563 0-0051: rtc core: registered hym8563 as rtc0
     
535. [    1.202117] i2c /dev entries driver
     
536. [    1.202793] IR NEC protocol handler initialized
     
537. [    1.202807] IR RC5(x) protocol handler initialized
     
538. [    1.202817] IR RC6 protocol handler initialized
     
539. [    1.202827] IR JVC protocol handler initialized
     
540. [    1.202836] IR Sony protocol handler initialized
     
541. [    1.202846] IR RC5 (streamzap) protocol handler initialized
     
542. [    1.202857] IR SANYO protocol handler initialized
     
543. [    1.202867] IR MCE Keyboard/mouse protocol handler initialized
     
544. [    1.203009] usbcore: registered new interface driver uvcvideo
     
545. [    1.203022] USB Video Class driver (1.1.1)
     
546. [    1.203034] CamSys driver version: v0.23.0,  CamSys head file version: v0.9.0
     
547. [    1.204405] D1:camsys_platform_probe(1067): 1-gpios-cifpower??? gpio=236
     
548. [    1.204429] D1:camsys_platform_probe(1070): gpios-cifpower??? gpio_request
     
549. [    1.204449] D1:camsys_platform_probe(1072): 1-gpios-cifpower??? gpio_request=0
     
550. [    1.204469] D1:camsys_platform_probe(1079): gpios-cifpower??? 236 high
     
551. [    1.204553] D1:camsys_mipiphy_probe_cb(163): ff910000.isp mipi phy0 probe success(reg_phy: 0x0  reg_vir: 0x0  size: 0x0)
     
552. [    1.204693] D1:camsys_mipiphy_probe_cb(160): ff910000.isp mipi phy1 probe success(reg_phy: 0xff968000  reg_vir: 0xf0da8000  size: 0x        4000)
     
553. [    1.205328] D1:camsys_platform_probe(1183): ff910000.isp memory:
     
554. [    1.205346] D1:camsys_platform_probe(1193):     Register memory (phy: 0xff910000 vir: 0xf0de0000 size: 0x10000)
     
555. [    1.205363] D1:camsys_platform_probe(1188):     I2c memory (phy: 0x2d6af000 vir: 0xed6af000 size: 0x1000)
     
556. [    1.205377] D1:camsys_platform_probe(1208): Probe ff910000.isp device success
     
557. [    1.206612] rockchip_temp_probe,line=362
     
558. [    1.265052] tsadc ff280000.tsadc: initialized
     
559. [    1.265432] device-mapper: uevent: version 1.0.3
     
560. [    1.265686] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
     
561. [    1.265983] Bluetooth: HCI UART driver ver 2.2
     
562. [    1.265998] Bluetooth: HCI H4 protocol initialized
     
563. [    1.266009] Bluetooth: HCILL protocol initialized
     
564. [    1.269089] cpufreq version 1.0, suspend freq 1200 MHz
     
565. [    1.269270] cpuidle: using governor ladder
     
566. [    1.269283] cpuidle: using governor menu
     
567. [    1.269319] Synopsys Designware Multimedia Card Interface Driver
     
568. [    1.269555] dwmmc_rockchip ff0f0000.rksdmmc: Version ID is 270a
     
569. [    1.269822] dwmmc_rockchip ff0f0000.rksdmmc: Using internal DMA controller.
     
570. [    1.269987] 3379..dw_mci_init_slot: fmin=400000, fmax=100000000 [mmc0]
     
571. [    1.270001] mmc0 : Rockchip specific MHSC: Ver 1.13 2014-09-05
     
572. [    1.270113] 1390..dw_mci_set_ios:  no card. [mmc0]
     
573. [    1.284736] 1390..dw_mci_set_ios:  no card. [mmc0]
     
574. [    1.304446] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out 800000Hz for init[mmc0]
     
575. [    1.304496] dwmmc_rockchip ff0f0000.rksdmmc: DW MMC controller at irq 67, 32 bit host data width, 256 deep fifo
     
576. [    1.304515] dwmmc_rockchip ff0f0000.rksdmmc: 1 slots initialized
     
577. [    1.304788] dwmmc_rockchip ff0c0000.rksdmmc: Version ID is 270a
     
578. [    1.305619] dwmmc_rockchip ff0c0000.rksdmmc: Using internal DMA controller.
     
579. [    1.305843] 3379..dw_mci_init_slot: fmin=400000, fmax=50000000 [mmc1]
     
580. [    1.305868] mmc1 : Rockchip specific MHSC: Ver 1.13 2014-09-05
     
581. [    1.305927] mmc1: no vmmc regulator found
     
582. [    1.306023] dwmmc_rockchip ff0c0000.rksdmmc: mmc1: No udbg pinctrl found!
     
583. [    1.306086] 1390..dw_mci_set_ios:  no card. [mmc1]
     
584. [    1.324092] 1390..dw_mci_set_ios:  no card. [mmc1]
     
585. [    1.336560] mmc0: BKOPS_EN bit is not set
     
586. [    1.338441] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 52000000Hz, actual 50000000HZ div = 1)
     
587. [    1.338465] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out normal clock [mmc0]
     
588. [    1.338515] rk_sdmmc: BOOT Bus speed=50000000Hz,Bus width=8bits.[mmc0]
     
589. [    1.338608] mmc0: new high speed MMC card at address 0001
     
590. [    1.338832] mmcblk0: mmc0:0001 AWMB3R 14.5 GiB
     
591. [    1.339096]  parameter: 0x000000000 -- 0x000400000 (4 MB)
     
592. [    1.339108]      uboot: 0x000400000 -- 0x000800000 (4 MB)
     
593. [    1.339117]       misc: 0x000800000 -- 0x000c00000 (4 MB)
     
594. [    1.339125]   resource: 0x000c00000 -- 0x001c00000 (16 MB)
     
595. [    1.339134]     kernel: 0x001c00000 -- 0x002c00000 (16 MB)
     
596. [    1.339142]       boot: 0x002c00000 -- 0x004c00000 (32 MB)
     
597. [    1.339151]   recovery: 0x004c00000 -- 0x006c00000 (32 MB)
     
598. [    1.339159]     backup: 0x006c00000 -- 0x00a000000 (52 MB)
     
599. [    1.339168]      cache: 0x00a000000 -- 0x012000000 (128 MB)
     
600. [    1.339177]     kpanic: 0x012000000 -- 0x012400000 (4 MB)
     
601. [    1.339185]     system: 0x012400000 -- 0x042400000 (768 MB)
     
602. [    1.339193]   metadata: 0x042400000 -- 0x042800000 (4 MB)
     
603. [    1.339202]   userdata: 0x042800000 -- 0x082800000 (1024 MB)
     
604. [    1.339210] radical_update: 0x082800000 -- 0x086800000 (64 MB)
     
605. [    1.339219]       user: 0x086800000 -- 0x3a3a00000 (12754 MB)
     
606. [    1.339243]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p151390..dw_mci_set_ios:  no card. [mmc1]
     
607. [    1.343814] dwmmc_rockchip ff0c0000.rksdmmc: DW MMC controller at irq 64, 32 bit host data width, 256 deep fifo
     
608. [    1.343826] dwmmc_rockchip ff0c0000.rksdmmc: 1 slots initialized
     
609. [    1.344087] dwmmc_rockchip ff0d0000.rksdmmc: Version ID is 270a
     
610. [    1.344268] dwmmc_rockchip ff0d0000.rksdmmc: Using internal DMA controller.
     
611. [    1.344372] 3379..dw_mci_init_slot: fmin=200000, fmax=50000000 [mmc2]
     
612. [    1.344382] mmc2 : Rockchip specific MHSC: Ver 1.13 2014-09-05
     
613. [    1.344629] 1390..dw_mci_set_ios:  no card. [mmc2]
     
614. [    1.363451] 1390..dw_mci_set_ios:  no card. [mmc2]
     
615. [    1.383134] 1390..dw_mci_set_ios:  no card. [mmc2]
     
616. [    1.383165] dwmmc_rockchip ff0d0000.rksdmmc: DW MMC controller at irq 65, 32 bit host data width, 256 deep fifo
     
617. [    1.383178] dwmmc_rockchip ff0d0000.rksdmmc: 1 slots initialized
     
618. [    1.383397] leds-gpio leds.34: pins are not configured from the driver
     
619. [    1.383600] hidraw: raw HID events driver (C) Jiri Kosina
     
620. [    1.384950] usbcore: registered new interface driver usbhid
     
621. [    1.384959] usbhid: USB HID core driver
     
622. [    1.385222] zram: Created 1 device(s) ...
     
623. [    1.385511] ashmem: initialized
     
624. [    1.385610] logger: created 256K log 'log_main'
     
625. [    1.385704] logger: created 256K log 'log_events'
     
626. [    1.385792] logger: created 256K log 'log_radio'
     
627. [    1.385880] logger: created 256K log 'log_system'
     
628. [    1.386859] input: rk29-keypad as /devices/ff100000.adc/key.36/input/input2
     
629. [    1.387630] es8323 probe i2c recv ok
     
630. [    1.387703] i2c-core: driver [ES8323] using legacy suspend method
     
631. [    1.387712] i2c-core: driver [ES8323] using legacy resume method
     
632. [    1.388461] rockchip-hdmi-spdif rockchip-hdmi-spdif.29: ASoC: CPU DAI (null) not registered
     
633. [    1.388489] rockchip_hdmi_spdif_audio_probe() register card failed:-517
     
634. [    1.388506] platform rockchip-hdmi-spdif.29: Driver rockchip-hdmi-spdif requests probe deferral
     
635. [    1.388731] es8323_probe
     
636. [    2.023090] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> NULL --> Left Line Mux
     
637. [    2.023103] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> NULL -> Left Line Mux
     
638. [    2.023113] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> NULL --> Left Line Mux
     
639. [    2.023121] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> NULL -> Left Line Mux
     
640. [    2.023131] ES8323 2-0010: ASoC: no dapm match for Left PGA Mux --> NULL --> Left Line Mux
     
641. [    2.023139] ES8323 2-0010: ASoC: Failed to add route Left PGA Mux -> NULL -> Left Line Mux
     
642. [    2.023148] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> NULL --> Right Line Mux
     
643. [    2.023156] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> NULL -> Right Line Mux
     
644. [    2.023165] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> NULL --> Right Line Mux
     
645. [    2.023173] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> NULL -> Right Line Mux
     
646. [    2.023182] ES8323 2-0010: ASoC: no dapm match for Right PGA Mux --> NULL --> Right Line Mux
     
647. [    2.023190] ES8323 2-0010: ASoC: Failed to add route Right PGA Mux -> NULL -> Right Line Mux
     
648. [    2.023199] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> LAMP --> Left PGA Mux
     
649. [    2.023207] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> LAMP -> Left PGA Mux
     
650. [    2.023216] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> LAMP --> Left PGA Mux
     
651. [    2.023223] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> LAMP -> Left PGA Mux
     
652. [    2.023232] ES8323 2-0010: ASoC: no dapm match for Differential Mux --> LAMP --> Left PGA Mux
     
653. [    2.023240] ES8323 2-0010: ASoC: Failed to add route Differential Mux -> LAMP -> Left PGA Mux
     
654. [    2.023249] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> RAMP --> Right PGA Mux
     
655. [    2.023256] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> RAMP -> Right PGA Mux
     
656. [    2.023265] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> RAMP --> Right PGA Mux
     
657. [    2.023273] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> RAMP -> Right PGA Mux
     
658. [    2.023282] ES8323 2-0010: ASoC: no dapm match for Differential Mux --> RAMP --> Right PGA Mux
     
659. [    2.023289] ES8323 2-0010: ASoC: Failed to add route Differential Mux -> RAMP -> Right PGA Mux
     
660. [    2.023298] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> LAMP --> Differential Mux
     
661. [    2.023306] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> LAMP -> Differential Mux
     
662. [    2.023315] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> RAMP --> Differential Mux
     
663. [    2.023322] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> RAMP -> Differential Mux
     
664. [    2.023331] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> LAMP --> Differential Mux
     
665. [    2.023338] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> LAMP -> Differential Mux
     
666. [    2.023347] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> RAMP --> Differential Mux
     
667. [    2.023354] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> RAMP -> Differential Mux
     
668. [    2.023374] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> LAMP --> Left Line Mux
     
669. [    2.023381] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> LAMP -> Left Line Mux
     
670. [    2.023390] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> LAMP --> Left Line Mux
     
671. [    2.023398] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> LAMP -> Left Line Mux
     
672. [    2.023406] ES8323 2-0010: ASoC: no dapm match for Left PGA Mux --> LAMP --> Left Line Mux
     
673. [    2.023414] ES8323 2-0010: ASoC: Failed to add route Left PGA Mux -> LAMP -> Left Line Mux
     
674. [    2.023423] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> RAMP --> Right Line Mux
     
675. [    2.023430] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> RAMP -> Right Line Mux
     
676. [    2.023439] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> RAMP --> Right Line Mux
     
677. [    2.023447] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> RAMP -> Right Line Mux
     
678. [    2.023455] ES8323 2-0010: ASoC: no dapm match for Right PGA Mux --> RAMP --> Right Line Mux
     
679. [    2.023463] ES8323 2-0010: ASoC: Failed to add route Right PGA Mux -> RAMP -> Right Line Mux
     
680. [    2.023571] ES8323 2-0010: ASoC: mux Right Line Mux has no paths
     
681. [    2.023583] ES8323 2-0010: ASoC: mux Left Line Mux has no paths
     
682. [    2.023592] ES8323 2-0010: ASoC: mux Right PGA Mux has no paths
     
683. [    2.023604] ES8323 2-0010: ASoC: mux Left PGA Mux has no paths
     
684. [    2.023623] ES8323 2-0010: ASoC: mux Differential Mux has no paths
     
685. [    2.026889] rockchip-es8323 rockchip-es8323.31:  ES8323 HiFi <-> rockchip-i2s.0 mapping ok
     
686. [    2.027208] input: RK_ES8323 Headphone Jack as /devices/rockchip-es8323.31/sound/card0/input3
     
687. [    2.027851] rockchip-hdmi-i2s rockchip-hdmi-i2s.28:  rk-hdmi-i2s-hifi <-> rockchip-i2s.0 mapping ok
     
688. [    2.028146] u32 classifier
     
689. [    2.028153]     Actions configured
     
690. [    2.028162] Netfilter messages via NETLINK v0.30.
     
691. [    2.028208] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
     
692. [    2.028452] ctnetlink v0.93: registering with nfnetlink.
     
693. [    2.028506] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
     
694. [    2.028513] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
     
695. [    2.028709] xt_time: kernel timezone is -0000
     
696. [    2.028866] ip_tables: (C) 2000-2006 Netfilter Core Team
     
697. [    2.028965] arp_tables: (C) 2002 David S. Miller
     
698. [    2.028995] TCP: cubic registered
     
699. [    2.029001] Initializing XFRM netlink socket
     
700. [    2.029166] NET: Registered protocol family 10
     
701. [    2.029560] mip6: Mobile IPv6
     
702. [    2.029583] ip6_tables: (C) 2000-2006 Netfilter Core Team
     
703. [    2.029671] sit: IPv6 over IPv4 tunneling driver
     
704. [    2.029925] NET: Registered protocol family 17
     
705. [    2.029946] NET: Registered protocol family 15
     
706. [    2.029986] Bridge firewalling registered
     
707. [    2.029996] Ebtables v2.0 registered
     
708. [    2.030118] Bluetooth: RFCOMM TTY layer initialized
     
709. [    2.030138] Bluetooth: RFCOMM socket layer initialized
     
710. [    2.030144] Bluetooth: RFCOMM ver 1.11
     
711. [    2.030150] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
     
712. [    2.030155] Bluetooth: BNEP filters: protocol multicast
     
713. [    2.030164] Bluetooth: BNEP socket layer initialized
     
714. [    2.030170] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
     
715. [    2.030179] Bluetooth: HIDP socket layer initialized
     
716. [    2.030199] l2tp_core: L2TP core driver, V2.0
     
717. [    2.030210] l2tp_ppp: PPPoL2TP kernel driver, V2.0
     
718. [    2.030217] [WLAN_RFKILL]: Enter rfkill_wlan_init
     
719. [    2.030356] [WLAN_RFKILL]: Enter rfkill_wlan_probe
     
720. [    2.030364] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = bcmwifi
     
721. [    2.030372] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
     
722. [    2.030379] [WLAN_RFKILL]: wlan_platdata_parse_dt: disable wifi io reference voltage control.
     
723. [    2.030386] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
     
724. [    2.030403] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,poweren_gpio = 156, flags = 0.
     
725. [    2.030420] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 158, flags = 0.
     
726. [    2.030428] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
     
727. [    2.030448] [WLAN_RFKILL]: rockchip_wifi_voltage_select: wifi & sdio reference voltage: 1.8V
     
728. [    2.030488] [WLAN_RFKILL]: Exit rfkill_wlan_probe
     
729. [    2.030523] [BT_RFKILL]: Enter rfkill_rk_init
     
730. [    2.030627] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 147.
     
731. [    2.030641] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,power_gpio = 155.
     
732. [    2.030653] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 157.
     
733. [    2.030665] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 154.
     
734. [    2.030677] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 159.
     
735. [    2.030713] [BT_RFKILL]: Request irq for bt wakeup host
     
736. [    2.030782] [BT_RFKILL]: ** disable irq
     
737. [    2.030848] [BT_RFKILL]: ap6335 device registered.
     
738. [    2.031640] rk3288-hdmi ff980000.hdmi: rk3288 hdmi probe sucess.
     
739. [    2.032315] VFP support v0.3: implementor 41 architecture 3 part 30 variant d rev 0
     
740. [    2.032331] rk3288_init_suspend
     
741. [    2.032338] rk3288_suspend_init enter
     
742. [    2.032449] rk3288_suspend_init: pm_ctrbits =200007
     
743. [    2.032474] gpio_get_dts_info suspend:4
     
744. [    2.032480] gpio_get_dts_info resume:4
     
745. [    2.032485] rockchip,pmic-suspend_gpios:14007a10 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
     
746. [    2.032510] rockchip,pmic-resume_gpios:2007a11 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
     
747. [    2.032658] clks_gating_suspend_init:clkgt info ok
     
748. [    2.032737] Registering SWP/SWPB emulation handler
     
749. [    2.033013] ddrfreq: verion 1.2 20140526
     
750. [    2.033022] ddrfreq: normal 396MHz video_1080p 240MHz video_4k 396MHz dualview 396MHz idle 0MHz suspend 200MHz reboot 396MHz
     
751. [    2.033030] ddrfreq: auto-freq=0
     
752. [    2.033035] ddrfreq: auto-freq-table[0] 240MHz
     
753. [    2.033040] ddrfreq: auto-freq-table[1] 324MHz
     
754. [    2.033046] ddrfreq: auto-freq-table[2] 396MHz
     
755. [    2.033051] ddrfreq: auto-freq-table[3] 528MHz
     
756. [    2.047460] regulator-dummy: disabling
     
757. [    2.047802] rockchip-hdmi-spdif rockchip-hdmi-spdif.29: ASoC: CPU DAI (null) not registered
     
758. [    2.047825] rockchip_hdmi_spdif_audio_probe() register card failed:-517
     
759. [    2.047840] platform rockchip-hdmi-spdif.29: Driver rockchip-hdmi-spdif requests probe deferral
     
760. [    2.047934] pcd_pullup, is_on 0
     
761. [    2.047968] file system registered
     
762. [    2.048470] android_usb gadget: Mass Storage Function, version: 2009/09/11
     
763. [    2.048479] android_usb gadget: Number of LUNs=2
     
764. [    2.048485]  lun0: LUN: removable file: (no medium)
     
765. [    2.048492]  lun1: LUN: removable file: (no medium)
     
766. [    2.048604] android_usb gadget: android_usb ready
     
767. [    2.049139] rtc_hym8563 0-0051: setting system clock to 2011-01-01 12:14:02 UTC (1293884042)
     
768. [    2.053680] rk_spdif:rk_spdif_init
     
769. [    2.053839] rk_spdif:Entered spdif_probe
     
770. [    2.054015] rk_spdif:spdif:spdif probe ok!
     
771. [    2.054485] usbcore: registered new interface driver snd-usb-audio
     
772. [    2.054501] ALSA device list:
     
773. [    2.054506]   #0: RK_ES8323
     
774. [    2.054511]   #1: RK-HDMI-I2S
     
775. [    2.054734] rockchip-hdmi-spdif rockchip-hdmi-spdif.29:  rk-hdmi-spdif-hifi <-> rockchip-spdif mapping ok
     
776. [    2.054839] Freeing unused kernel memory: 592K (c0af1000 - c0b85000)
     
777. [    2.059355] SELinux:  Permission attach_queue in class tun_socket not defined in policy.
     
778. [    2.059367] SELinux: the above unknown classes and permissions will be denied
     
779. [    2.271735] type=1403 audit(1293884042.720:2): policy loaded auid=4294967295 ses=4294967295
     
780. [    2.271837] SELinux: Loaded policy from /sepolicy
     
781. [    2.273284] type=1404 audit(1293884042.720:3): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
     
782. [    2.672234] rk3288-hdmi ff980000.hdmi: Removed.
     
783. [    2.672246] hdmi connect to lcdc1
     
784. [    2.672489] rk3288-lcdc lcdc1: lcdc1: dclk:74250000>>fps:60
     
785. [    2.672499] rk3288-lcdc lcdc1: wakeup from standby!
     
786. [    2.672509] rk3288-lcdc lcdc1: lcdc1: dclk:74250000>>fps:60
     
787. [    2.819756] dwc_otg_hcd_enable, enable host controller
     
788. [    2.942763] Using Buffer DMA mode
     
789. [    2.942770] Periodic Transfer Interrupt Enhancement - disabled
     
790. [    2.942776] Multiprocessor Interrupt Enhancement - disabled
     
791. [    2.942782] OTG VER PARAM: 0, OTG VER FLAG: 0
     
792. [    2.942788] ^^^^^^^^^^^^^^^^^^Host Mode
     
793. [    2.987139] Init: Power Port (0)
     
794. [    2.987175] ff540000.usb resume, HPRT0:0x21401
     
795. [    3.124850] Indeed it is in host mode hprt0 = 00021501
     
796. [    3.301960] usb 3-1: new high-speed USB device number 2 using usb20_host
     
797. [    3.302035] Indeed it is in host mode hprt0 = 00001101
     
798. [    3.498952] usb 3-1: New USB device found, idVendor=1a40, idProduct=0101
     
799. [    3.498966] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
     
800. [    3.498974] usb 3-1: Product: USB 2.0 Hub [MTT]
     
801. [    3.499321] hub 3-1:1.0: USB hub found
     
802. [    3.499378] hub 3-1:1.0: 4 ports detected
     
803. [    3.616838] ff540000.usb suspend, HPRT0:0x1485
     
804. [    3.711710] init: /dev/hw_random not found
     
805. [    3.712872] type=1400 audit(1293884044.180:4): avc:  denied  { mount } for  pid=1 comm="init" name="/" dev="functionfs" ino=3138 sco        ntext=u:r:kernel:s0 tcontext=u:object_r:unlabeled:s0 tclass=filesystem permissive=1
     
806. [    3.712956] android_usb: already disabled
     
807. [    3.713077] init: property 'ro.serialno' doesn't exist while expanding '${ro.serialno}'
     
808. [    3.713088] init: cannot expand '${ro.serialno}' while writing to '/sys/class/android_usb/android0/iSerial'
     
809. [    3.713173] drmboot: module license 'unspecified' taints kernel.
     
810. [    3.713181] Disabling lock debugging due to kernel taint
     
811. [    3.714251] %s: ok, 20130810
     
812. [    8.185776] init: /sbin/e2fsck terminated by exit(8)
     
813. [    8.185803] init: Operational error while checking volume '/dev/block/p
     
814. __bim/ec_opbn-nzda/ca co'
     
815. n't  8.18any6] data: Fenllooto g fnt loca/blme!/plabiorm/_opc/btzdate/ccoue, 't mand t t tzxt4a when[  oki.18for1] Tni
     
816.                                                                                                                       __/denicw_ren_om         rStertingirecoveyy /d Sa/pran rty12:1no:8 2pen poriistles
     
817.                                            [
     
818. m.18ne=4] solroid_FIQ: andrady oisahard
     
819. re=  80board9] drot: ootnconepre=ttedIQ0ntax f.apspes_ayin= prnitrtynito.ptdpurtsman29xctund:0x0use200namx00instea(pa[  ete.18054000ini        0@0usi002000(ecatt),synt00200r sx00ify000 prsper0x0'ro800oduct.006el'(rese $cnam0x0ins800d
     
820. p[  x00.180008] ini500procacty ,0x000ria00@' d009n000exianiwhi0x0exp0ndi@0x'$r920erialntem{na036 in(baad
     
821.                                                                                           [ x008.1000@0x in120 camettdatpan0x0$ro000ria        4340008.1er)10]oraad eesc=emtorloa[    8mes092p=2rea-11-27ngs:44    an1ro955ootcd_rialup=100_on000
     
822.                                                                                                   00019D androidboot.mode=emmc
     
823. 
     
824. cmdline=console=ttyFIQ0 androidboot.hardware=rk30board androidboot.console=ttyFIQ0 board.ap_has_alsa=0 init=/init  mtdparts=rk29xxnand:        0x00002000@0x00000000(parameter),0x00002000@0x00002000(uboot),0x00002000@0x00004000(misc),0x00008000@0x00006000(resource),0x00008000@0x        0000e000(kernel),0x00010000@0x00016000(boot),0x00010000@0x00026000(recovery),0x0001a000@0x00036000(backup),0x00040000@0x00050000(cache)        ,0x00002000@0x00090000(kpanic),0x00180000@0x00092000(system),0x00002000@0x00212000(metadata),0x00200000@0x00214000(userdata),0x00020000        @0x00414000(radical_update),-@0x00434000(user) storagemedia=emmc loader.timestamp=2014-11-27_16:44:27 androidboot.serialno=100612000000        019D androidboot.mode=emmc
     
825. 
     
826. bootmode = emmc
     
827. recovery filesystem table
     
828. =========================
     
829.   0 /mnt/internal_sd vfat /dev/block/platform/ff0f0000.rksdmmc/by-name/user 0
     
830.   1 /mnt/external_sd vfat /dev/block/mmcblk1p1 0
     
831.   2 /system ext4 /dev/block/platform/ff0f0000.rksdmmc/by-name/system 0
     
832.   3 /cache ext4 /dev/block/platform/ff0f0000.rksdmmc/by-name/cache 0
     
833.   4 /metadata ext4 /dev/block/platform/ff0f0000.rksdmmc/by-name/metadata 0
     
834.   5 /data ext4 /dev/block/platform/ff0f0000.rksdmmc/by-name/userdata 0
     
835.   6 /cust ext4 /dev/block/platform/ff0f0000.rksdmmc/by-name/cust 0
     
836.   7 /custom ext4 /dev/block/platform/ff0f0000.rksdmmc/by-name/custom 0
     
837.   8 /radical_update ext4 /dev/block/platform/ff0f0000.rksdmmc/by-name/radical_update 0
     
838.   9 /misc emmc /dev/block/platform/ff0f0000.rksdmmc/by-name/misc 0
     
839.   10 /uboot emmc /dev/block/platform/ff0f0000.rksdmmc/by-name/uboot 0
     
840.   11 /charge emmc /dev/block/platform/ff0f0000.rksdmmc/by-name/charge 0
     
841.   12 /resource emmc /dev/block/platform/ff0f0000.rksdmmc/by-name/resource 0
     
842.   13 /parameter emmc /dev/block/platform/ff0f0000.rksdmmc/by-name/parameter 0
     
843.   14 /boot emmc /dev/block/platform/ff0f0000.rksdmmc/by-name/boot 0
     
844.   15 /recovery emmc /dev/block/platform/ff0f0000.rksdmmc/by-name/recovery 0
     
845.   16 /backup emmc /dev/block/platform/ff0f0000.rksdmmc/by-name/backup 0
     
846.   17 /tmp ramdisk ramdisk 0
     
847. 
     
848. I/ [File] : bootable/recovery/recovery.cpp; [Line] : 1553; [Func] : void SetSdcardRootPath(); InternalSD_ROOT: /mnt/internal_sd
     
849. I/ [File] : bootable/recovery/recovery.cpp; [Line] : 1555; [Func] : void SetSdcardRootPath(); ExternalSD_ROOT: /mnt/external_sd
     
850. failed to create /cache dir,err=File exists!
     
851. [    8.490736] EXT4-fs (mmcblk0p9): recovery complete
     
852. failed to read font: res=-1
     
853. can't open /dev/tty0: No such file or directory
     
854. framebuffer: fd 7 (1280 x 800)
     
855. [    8.491283] EXT4-fs (mmcblk0p9): mounted filesystem with ordered data mode. Opts:
     
856. [    8.499457] I'am in gsl_ts_suspend() start
     
857. [    8.499463] gsl_ts_suspend () : cancel gsl_monitor_work
     
858. [    8.536847] hdmi remove from lcdc1
     
859. [    8.536857] rk3288-lcdc lcdc1: no layer is used,go to standby!
     
860. [    8.562559] rk3288-hdmi ff980000.hdmi: Removed.
     
861. [    8.588392] rk3288-lcdc lcdc0: blank mode:4
     
862. [    8.633254] rk3288-lcdc lcdc0: blank mode:0
     
863. [    8.633266] I'am in gsl_ts_resume() start
     
864. [    8.723767] ----------3680A---------
     
865. [    8.733612] ***************vbus detect*****************
     
866. [    8.783459] gsl_ts_read set data address fail! ret=-11-0xfffffff5
     
867. [    8.783 inst####n####xt:   mem r @d1896)
     
868. 0 0 0 0 #########
     
869. [    8.841842] test_i2c-394: Enter
     
870. [      8424  ergsl_ts_rea:  (1 xa1 @ 1dress fail! ret=-11-0xfffffff5
     
871. test_i2c-413: Exit_ts_read set data address fail!   no-11-0xfffffff:  (1   8.881599)
     
872. [    8.881855] - ----gs      test_i2c :  (r-----@
     
873. [99) 8.881869] gsl_ts_resume () : queue gsl_monitor_work
     
874. [    8.912859] Using Buffer DMA mode
     
875. [    8.912873] Periodic Transfer Interrupt Enhancement - disabled
     
876. [    8.912881] Multiprocessor Interrupt Enhancement - disabled
     
877. [    8.912890] OTG VER PARAM: 0, OTG VER FLAG: 0
     
878. [    8.912897] ^^^^^^^^^^^^^^^^^Device Mode
     
879. [    8.912939] *******************soft connect!!!*******************
     
880. [    9.032608] USB RESET
     
881. Recovery system v4.4.2
     
882. 
     
883. [    9.090084] android_work: sent uevent USB_STATE=CONNECTED
     
884. Recovery system v4.4.2
     
885. in get_args
     
886. I/ [File] : bootable/recovery/recovery.cpp; [Line] : 760; [Func] : bool get_args(int*, char***, bool*); Boot command: boot-recovery
     
887. I/ [File] : bootable/recovery/recovery.cpp; [Line] : 779; [Func] : bool get_args(int*, char***, bool*); Got arguments from boot message
     
888. list arg=2:
     
889. recovery
     
890. --wipe_all
     
891. bootmode = emmc
     
892. ro.rk.cpu=rk3288v1
     
893. ro.rk.soc=rk3288
     
894. ro.rk.bt_enable=true
     
895. ro.rk.systembar.tabletUI=false
     
896. ro.rk.systembar.voiceicon=true
     
897. ro.rk.MassStorage=false
     
898. ro.rk.cpu_min_freq=126000
     
899. 
     
900. ro.rk.homepage_base=http://www.google.com/webhp?client={CID}&source=android-home
     
901. ro.rk.def_brightness=200
     
902. ro.rk.screenoff_time=60000
     
903. ro.rk.screenshot_enable=true
     
904. ro.rk.LowBatteryBrightness=true
     
905. ro.rk.install_non_market_apps=false
     
906. ro.sf.hwrotation=0
     
907. ro.sf.lcd_density=160
     
908. ro.sf.fakerotation=false
     
909. ro.adb.secure=0
     
910. ro.com.google.gmsversion=4.4_r4
     
911. ro.com.android.dateformat=MM-dd-yyyy
     
912. ro.com.android.dataroaming=true
     
913. ro.ril.ecclist=112,911
     
914. ro.sms.capable=false
     
915. ro.boot.mode=emmc
     
916. ro.boot.console=ttyFIQ0
     
917. ro.boot.hardware=rk30board
     
918. ro.boot.serialno=100612000000019D
     
919. ro.hwui.path_cache_size=16
     
920. ro.hwui.layer_cache_size=48
     
921. ro.hwui.shape_cache_size=4
     
922. ro.hwui.texture_cache_size=72
     
923. ro.hwui.disable_scissor_opt=true
     
924. ro.hwui.gradient_cache_size=1
     
925. ro.hwu998] U_shaESE_
     
926. [    ize=6
     
927. 8o.hwdroidxt_lagge_cachhigh-th=2d 8onrog #1i.tndroida
     
928. _ro.k:usentxt_veng USachTAheiCON=1024                [ l  9ach552idtand024
     
929. ro.hwui.text_small_cache_height=1024
     
930. ro.wifi.channels=
     
931. ro.allow.mock.location=1
     
932. ro.audio.monitorOrientation=true
     
933. ro.board.platform=rk3288
     
934. ro.build.id=KTU84Q
     
935. ro.build.date=2014?1′ 12??? 30?—￥ ???????o? 15:45:49 CST
     
936. ro.build.date.utc=1419925549
     
937. ro.build.host=midserver
     
938. ro.build.tags=test-keys
     
939. ro.build.type=eng
     
940. ro.build.user=firefly
     
941. ro.build.display.id=rk3288-eng 4.4.4 KTU84Q eng.firefly.20141230.154515 test-keys
     
942. ro.build.product=rk3288
     
943. ro.build.version.sdk=19
     
944. ro.build.version.release=4.4.4
     
945. ro.build.version.codename=REL
     
946. ro.build.version.incremental=eng.firefly.20141230.154515
     
947. ro.build.description=rk3288-eng 4.4.4 KTU84Q eng.firefly.20141230.154515 test-keys
     
948. ro.build.fingerprint=rockchip/rk3288/rk3288:4.4.4/KTU84Q/eng.firefly.20141230.154515:eng/test-keys
     
949. ro.build.characteristics=tablet
     
950. ro.rksdk.version=RK30_ANDROID4.4.4-SDK-v1.00.00
     
951. ro.voice.capable=false
     
952. ro.ap_mdm=-1
     
953. ro.config.ringtone=Ring_Synth_04.ogg
     
954. ro.config.alarm_alert=Alarm_Classic.ogg
     
955. ro.config.notification_sound=pixiedust.ogg
     
956. ro.kernel.android.checkjni=0
     
957. ro.secure=0
     
958. ro.tether.denied=false
     
959. ro.carrier=unknown
     
960. ro.default.size=100
     
961. ro.factory.tool=0
     
962. ro.factory.hasGPS=false
     
963. ro.factory.hasUMS=true
     
964. ro.factory.without_battery=false
     
965. ro.factory.storage_suppntfs=true
     
966. ro.product.cpu.abi=armeabi-v7a
     
967. ro.product.cpu.abi2=armeabi
     
968. ro.product.ota.host=www.rockchip.com:2300
     
969. ro.product.name=rk3288
     
970. ro.product.board=rk30sdk
     
971. ro.product.brand=rockchip
     
972. ro.product.model=rk3288
     
973. ro.product.device=rk3288
     
974. ro.product.locale.region=US
     
975. ro.product.locale.language=en
     
976. ro.product.version=1.0.0
     
977. ro.product.usbfactory=rockchip_usb
     
978. ro.product.manufacturer=rockchip
     
979. ro.baseband=unknown
     
980. ro.bootmode=emmc
     
981. ro.hardware=rk30board
     
982. ro.opengles.version=196608
     
983. ro.revision=0
     
984. ro.bootloader=unknown
     
985. ro.debuggable=1
     
986. ro.ap_has_alsa=-1
     
987. ro.factorytest=0
     
988. ro.setupwizard.mode=OPTIONAL
     
989. ro.ap_data_only=-1
     
990. ro.ap_has_earphone=-1
     
991. sf.power.control=8847360
     
992. net.bt.name=Android
     
993. net.change=net.bt.name
     
994. ril.function.dataonly=1
     
995. sys.hwc.compose_policy=6
     
996. sys.rkadb.root=0
     
997. sys.wallpaper.rgb565=0
     
998. sys.resolution.changed=false
     
999. init.svc.adbd=running
     
1000. init.svc.console=restarting
      
1001. init.svc.ueventd=running
      
1002. init.svc.recovery=running
      
1003. rild.libargs=-d /dev/ttyACM0
      
1004. rild.libpath=/system/lib/libril-rk29-dataonly.so
      
1005. rild.libpath1=/system/lib/libreference-ril-mt6229.so
      
1006. rild.libpath2=/system/lib/libreference-ril-mu509.so
      
1007. rild.libpath4=/system/lib/libreference-ril-mw100.so
      
1008. rild.libpath6=/system/lib/libreference-ril-sc6610.so
      
1009. rild.libpath7=/system/lib/libreference-ril-m51.so
      
1010. rild.libpath8=/system/lib/libreference-ril-mt6250.so
      
1011. rild.libpath9=/system/lib/libreference-ril-c66a.so
      
1012. rild.libpath10=/system/lib/libreference-ril-sew290.so
      
1013. rild.libpath11=/system/lib/libreference-ril-u5501.so
      
1014. rild.libpath12=/system/lib/libreference-ril-u7501.so
      
1015. rild.libpath13=/system/lib/libreference-ril-aw706.so
      
1016. rild.libpath14=/system/lib/libreference-ril-a85xx.so
      
1017. rild.libpath15=/system/lib/libreference-ril-e1230s.so
      
1018. wifi.interface=wlan0
      
1019. wifi.supplicant_scan_interval=15
      
1020. debug.nfc.se=false
      
1021. debug.nfc.fw_download=false
      
1022. rild1.libpath=/system/lib/libreference-ril-sc6610-1.so
      
1023. rild3.libpath=/system/lib/libril-rk29-dataonly.so
      
1024. dalvik.vm.jniopts=warnonly
      
1025. dalvik.vm.heapsize=512m
      
1026. dalvik.vm.lockprof.threshold=500
      
1027. dalvik.vm.heapmaxfree=8m
      
1028. dalvik.vm.heapminfree=512k
      
1029. dalvik.vm.dexopt-flags=m=y
      
1030. dalvik.vm.heapstartsize=16m
      
1031. dalvik.vm.heapgrowthlimit=192m
      
1032. dalvik.vm.stack-trace-file=/data/anr/traces.txt
      
1033. dalvik.vm.heaptargetutilization=0.75
      
1034. persist.sys.ui.hw=true
      
1035. persist.sys.usb.config=mass_storage,adb
      
1036. persist.sys.dalvik.vm.lib=libdvm.so
      
1037. persist.sys.timezone=
      
1038. persist.sys.strictmode.visual=false
      
1039. persist.tegra.nvmmlite=1
      
1040. testing.mediascanner.skiplist=/mnt/internal_sd/Android/
      
1041. keyguard.no_require_sim=true
      
1042. ExternalSD_ROOT=/mnt/external_sd
      
1043. InternalSD_ROOT=/mnt/internal_sd
      
1044. UserVolumeLabel=RockChips
      
1045. failed to create /metadata dir,err=File exists!
      
1046. in do_wipe_all
      
1047. E:clone_data_if_exist->can't find databk cmdline
      
1048. E/ [File] : bootable/recovery/recovery.cpp; [Line] : 418; [Func] : int clone_data_if_exist(); clone_data_if_exist->can't find databk cm        dline
      
1049. Formatting /data...
      
1050. format '/dev/block/platform/ff0f0000.rksdmmc/by-name/userdata' to ext4 filesystem
      
1051. executing '/sbin/mke2fs'
      
1052. executed '/sbin/mke2fs' done
      
1053. executed '/sbin/mke2fs' return 0
      
1054. executing '/sbin/e2fsck'
      
1055. e2fsck 1.41.14 (22-Dec-2010)
      
1056. Pass 1: Checking inodes, blocks, and sizes
      
1057. Pass 2: Checking directory structure
      
1058. Pass 3: Checking directory connectivity
      
1059. Pass 4: Checking reference counts
      
1060. Pass 5: Checking group summary information
      
1061. /dev/block/platform/ff0f0000.rksdmmc/by-name/userdata: 11/65536 files (0.0% non-contiguous), 12635/262144 blocks
      
1062. executed '/sbin/e2fsck' done
      
1063. executed '/sbin/e2fsck' return 0
      
1064. [    9.550402] rk3288-hdmi ff980000.hdmiattimoved.che...
      
1065. .550414] hdmi connect to lcdc1
      
1066. [    9.550454] rk3288-lcdc lcdc1: lcdc1: dclk:74250000>>fps:60
      
1067. [    9.550462] rk3288-lcdc lcdc1: wakeup from standby!
      
1068. [    9.550472] rk3288-lcdc lcdc1: lcdc1: dclk:74250000>>fps:60
      
1069. [    9.556127] EXT4-fs (mmcblk0p12): recovery complete
      
1070. [    9.556140] EXT4-fs (mmcblk0p12): mounted filesystem with ordered data mode. Opts:
      
1071. [   11.735906] EXT4-fs (mmcblk0p13): mounted filesystem with ordered data mode. Opts:
      
1072. format '/dev/block/platform/ff0f0000.rksdmmc/by-name/cache' to ext4 filesystem
      
1073. executing '/sbin/mke2fs'
      
1074. [   11.843711] gsl_ts_read set data address fail! ret=-11-0xfffffff5
      
1075. [   11.844369] gsl_ts_read set data address fail! ret=-11-0xfffffff5
      
1076. [   11.844380] ======int_1st: 0 0 0 0 , int_2nd: 0 0 0 0 ======
      
1077. [   11.845022] gsl_ts_read set data address fail! ret=-11-0xfffffff5
      
1078. [   11.902146] test_i2c-394: Enter
      
1079. [   11.902879] gsl_ts_read set data address fail! ret=-11-0xfffffff5
      
1080. [   11.942367] gsl_ts_read set data address fail! ret=-11-0xfffffff5
      
1081. [   11.942392] test_i2c-413: Exit
      
1082. [   11.942398] ------gslX680 test_i2c error------
      
1083. executed '/sbin/mke2fs' done
      
1084. executed '/sbin/mke2fs' return 0
      
1085. executing '/sbin/e2fsck'
      
1086. e2fsck 1.41.14 (22-Dec-2010)
      
1087. Pass 1: Checking inodes, blocks, and sizes
      
1088. Pass 2: Checking directory structure
      
1089. Pass 3: Checking directory connectivity
      
1090. Pass 4: Checking reference counts
      
1091. Pass 5: Checking group summary information
      
1092. /dev/block/platform/ff0f0000.rksdmmc/by-name/cache: 11/32768 files (9.1% non-contiguous), 5137/32768 blocks
      
1093. executed '/sbin/e2fsck' done
      
1094. executed '/sbin/e2fsck' return 0
      
1095. [   12.600939] EXT4-fs (mmcblk0p9): mounted filesystem with ordered data mode. Opts:
      
1096. resize /system
      
1097. executing '/sbin/e2fsck'
      
1098. e2fsck 1.41.14 (22-Dec-2010)
      
1099. Pass 1: Checking inodes, blocks, and sizes
      
1100. Pass 2: Checking directory structure
      
1101. Pass 3: Checking directory connectivity
      
1102. Pass 4: Checking reference counts
      
1103. Pass 5: Checking group summary information
      
1104. system: 1748/43488 files (0.0% non-contiguous), 115840/196608 blocks
      
1105. executed '/sbin/e2fsck' done
      
1106. executed '/sbin/e2fsck' return 0
      
1107. executing '/sbin/resize2fs'
      
1108. resize2fs 1.41.14 (22-Dec-2010)
      
1109. The filesystem is already 196608 blocks long.  Nothing to do!
      
1110. 
      
1111. executed '/sbin/resize2fs' done
      
1112. executed '/sbin/resize2fs' return 0
      
1113. D/ [File] : bootable/recovery/recovery.cpp; [Line] : 1957; [Func] : int do_wipe_all(Device*); to wipe radical_update_partition.
      
1114. Formatting /radical_update...
      
1115. format '/dev/block/platform/ff0f0000.rksdmmc/by-name/radical_update' to ext4 filesystem
      
1116. executing '/sbin/mke2fs'
      
1117. [   12.926129] gsl_ts_read set data address fail! ret=-11-0xfffffff5
      
1118. [   12.926151] ======read 0xb0: 0 0 0 0 ======
      
1119. [   12.926807] gsl_ts_read set data address fail! ret=-11-0xfffffff5
      
1120. [   12.926817] ======int_1st: 0 0 0 0 , int_2nd: 0 0 0 0 ======
      
1121. [   12.927474] gsl_ts_read set data address fail! ret=-11-0xfffffff5
      
1122. [   12.984481] test_i2c-394: Enter
      
1123. [   12.985160] gsl_ts_read set data address fail! ret=-11-0xfffffff5
      
1124. [   13.024498] gsl_ts_read set data address fail! ret=-11-0xfffffff5
      
1125. [   13.024514] test_i2c-413: Exit
      
1126. [   13.024520] ------gslX680 test_i2c error------
      
1127. sh: applet not found
      
1128. executed '/sbin/mke2fs' done
      
1129. executed '/sbin/mke2fs' return 0
      
1130. executing '/sbin/e2fsck'
      
1131. e2fsck 1.41.14 (22-Dec-2010)
      
1132. Pass 1: Checking inodes, blocks, and sizes
      
1133. Pass 2: Checking directory structure
      
1134. Pass 3: Checking directory connectivity
      
1135. Pass 4: Checking reference counts
      
1136. Pass 5: Checking group summary information
      
1137. /dev/block/platform/ff0f0000.rksdmmc/by-name/radical_update: 11/16384 files (9.1% non-contiguous), 1549/16384 blocks
      
1138. executed '/sbin/e2fsck' done
      
1139. executed '/sbin/e2fsck' return 0
      
1140. ordered data mode. Opts: cblFor14)tinountnt/inlesnalem w..
      
1141. I/ [File] : bootable/recovery/roots.cpp; [Line] : 268; [Func] : format_volume; VolumeLabel: RockChips
      
1142. format '/dev/block/platform/ff0f0000.rksdmmc/by-name/user' to vfat filesystem
      
1143. executing '/sbin/mkdosfs'
      
1144. opening /dev/block/platform/ff0f0000.rksdmmc/by-name/user
      
1145. /dev/block/platform/ff0f0000.rksdmmc/by-name/user: 26094656 sectors in 1630916 FAT32 clusters (8192 bytes/cluster)
      
1146. MBR type: 11
      
1147. bps=512 spc=16 res=32 nft=2 mid=0xf0 spt=26120192 hds=0 hid=0 bsec=26120192 bspf=12752 rdcl=2 infs=1 bkbs=2
      
1148. executed '/sbin/mkdosfs' done
      
1149. executed '/sbin/mkdosfs' return 0
      
1150. failed to create /mnt/external_sd dir,err=File exists!
      
1151. W/ [File] : bootable/recovery/roots.cpp; [Line] : 139; [Func] : ensure_path_mounted; failed to mount /dev/block/mmcblk1p1 at /mnt/exter        nal_sd,type=vfat (No such file or directory)
      
1152. W/ [File] : bootable/recovery/roots.cpp; [Line] : 144; [Func] : ensure_path_mounted; failed to mount /dev/block/mmcblk1p1 at /mnt/exter        nal_sd,type=ntfs (No such device)
      
1153. W/ [File] : bootable/recovery/roots.cpp; [Line] : 155; [Func] : ensure_path_mounted; failed to mount /dev/block/mmcblk1 at /mnt/externa        l_sd,type=vfat (No such file or directory)
      
1154. W/ [File] : bootable/recovery/roots.cpp; [Line] : 160; [Func] : ensure_path_mounted; failed to mount /dev/block/mmcblk1 at /mnt/externa        l_sd,type=ntfs (No such device)
      
1155. I/ [File] : bootable/recovery/recovery.cpp; [Line] : 962; [Func] : void finish_recovery(const char*); clear bootloader message
      
1156. Rebooting...
      
1157. [   13.947343] SysRq : Emergency Remount R/O
      
1158. [   13.948371] EXT4-fs (mmcblk0p12): re-mounted. Opts: (null)
      
1159. [   13.953086] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
      
1160. [   13.953759] EXT4-fs (mmcblk0p14): re-mounted. Opts: (null)
      
1161. [   13.953816] Emergency Remount complete
      
1162. [   14.008533] gsl_ts_read set data address fail! ret=-11-0xfffffff5
      
1163. [   14.009202] gsl_ts_read set data address fail! ret=-11-0xfffffff5
      
1164. [   14.009213] ======int_1st: 0 0 0 0 , int_2nd: 0 0 0 0 ======
      
1165. [   14.009870] gsl_ts_read set data address fail! ret=-11-0xfffffff5
      
1166. [   14.046544] cpufreq: cpufreq: reboot set core rate=1200000000, volt=1100000
      
1167. [   14.046717] mmcblk mmc0:0001: Unbalanced pm_runtime_enable!
      
1168. [   14.076394] test_i2c-394: Enter
      
1169. [   14.080177] gsl_ts_read set data address fail! ret=-11-0xfffffff5
      
1170. [   14.116737] gsl_ts_read set data address fail! ret=-11-0xfffffff5
      
1171. [   14.122722] test_i2c-413: Exit
      
1172. [   14.125721] ------gslX680 test_i2c error------
      
1173. [   14.678113] Chenzy-------hkw-------es8323_i2c_shutdown
      
1174. [   14.784240] dwc_otg_driver_shutdown: disconnect USB device mode
      
1175. [   14.794061] Restarting system.
      
1176. DDR Version 1.00 20141007
      
1177. In
      
1178. SRX
      
1179. Channel a: DDR3 200MHz
      
1180. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
      
1181. Channel b: DDR3 200MHz
      
1182. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
      
1183. OUT
      
1184. 
      
1185. 
      
1186. U-Boot 2014.10-RK3288-01 (Nov 27 2014 - 16:44:27)
      
1187. 
      
1188. CPU: rk3288
      
1189. CPU's clock information:
      
1190.     arm pll = 600000000HZ
      
1191.     periph pll = 297000000HZ
      
1192.     ddr pll = 200000000HZ
      
1193.     codec pll = 384000000HZ
      
1194. Board:  Rockchip platform Board
      
1195. DRAM:  Found dram banks:1
      
1196. Adding bank:0000000000000000(0000000080000000)
      
1197. 128 MiB
      
1198. storage init OK!
      
1199. Using default environment
      
1200. 
      
1201. GetParam
      
1202. check parameter success
      
1203. Unknow param: MACHINE_MODEL:rk30sdk!
      
1204. Unknow param: MACHINE_ID:007!
      
1205. Unknow param: MANUFACTURER:RK30SDK!
      
1206. Unknow param: PWR_HLD: 0,0,A,0,1!
      
1207. failed to prepare fdt from boot!
      
1208. power key: bank-0 pin-5
      
1209. pmic:act8846
      
1210. SecureBootEn = 0, SecureBootLock = 0
      
1211. 
      
1212. #Boot ver: 2014-11-27#2.19
      
1213. sn:100612000000019D
      
1214. checkKey
      
1215. vbus = 1
      
1216. no fuel gauge found
      
1217. no fuel gauge found
      
1218. read logo_on switch from dts [0]
      
1219. no fuel gauge found
      
1220. Hit any key to stop autoboot:  1
      

复制代码

下面是recovery的信息


恢复完是能够重启的。

B.第二个问题，我单独烧写resource.img分区的时候，串口的打印只能打印到Starting kernel ...然后后面什么都没有了！
C.第三个问题，如果我同时烧写misc.img和resource.img分区的时候，系统起不来，串口只能打印到Starting kernel ...,界面停留在firefly，
  adb有显示出来，但是连接不上

3.我单独烧写另外几个分区的时候，没有什么问题，那我觉得下面这两个就有问题，

• misc.img ：misc 分区映像，负责启动模式切换和急救模式的参数传递。
• resource.img ：资源映像，内含开机图片和内核的设备树信息。
  

  因为是第一次用这个板，所以也不知道啥原因，请问有人能提供帮忙么？
4.注：系统起不来的时候我是用Firefly-RK3288_PAD_Android4.4_201412301550.img来重新烧写一遍的，而之后烧写自己编译的时候，
      没有对烧写的参数做任何的修改。

zhansb

parameter有用SDK下面的吗，可以parameter把贴出来看看

zhutousame

多谢版主，我试了发现确实是parameter又问题，我拷贝了下面的这个
./FFTools/parameter/rk3288-3.10-uboot-android-data1G.parameter.txt
就好了
FIRMWARE_VER:4.4.2
MACHINE_MODEL:rk30sdk
MACHINE_ID:007
MANUFACTURER:RK30SDK
MAGIC: 0x5041524B
ATAG: 0x60000800
MACHINE: 3066
CHECK_MASK: 0x80
PWR_HLD: 0,0,A,0,1
#KERNEL_IMG: 0x62008000
#FDT_NAME: rk-kernel.dtb
#RECOVER_KEY: 1,1,0,20,0
CMDLINE:console=ttyS2 earlyprintk androidboot.hardware=rk30board androidboot.console=ttyS2 board.ap_has_alsa=0 init=/init initrd=0x62000000,0x00800000 mtdparts=rk29xxnand:0x00002000@0x00002000(uboot),0x00002000@0x00004000(misc),0x00008000@0x00006000(resource),0x00008000@0x0000e000(kernel),0x00010000@0x00016000(boot),0x00010000@0x00026000(recovery),0x0001a000@0x00036000(backup),0x00040000@0x00050000(cache),0x00002000@0x00090000(kpanic),0x00180000@0x00092000(system),0x00002000@0x00212000(metadata),0x00200000@0x00214000(userdata),0x00020000@0x00414000(radical_update),-@0x00434000(user)

烟云龙紫

zhansb 发表于 2015-3-31 10:20
parameter有用SDK下面的吗，可以parameter把贴出来看看

这个问题具体怎么解决的呢，楼主或者版主能否给个说明，我这边也遇到此类似问题。我在Windows下用2.33烧写工具 烧写自己编译的固件不行，烧写官方给的固件都可以

zhansb

烟云龙紫 发表于 2015-4-15 15:53
这个问题具体怎么解决的呢，楼主或者版主能否给个说明，我这边也遇到此类似问题。我在Windows下用2.33烧 ...

我拷贝了下面的这个
./FFTools/parameter/rk3288-3.10-uboot-android-data1G.parameter.txt

楼上已经把解决问题的方法贴出来的

烟云龙紫

zhansb 发表于 2015-4-15 16:23
楼上已经把解决问题的方法贴出来的

这个是SDK目录下的东西吗，我的SDK下没有这个目录的文件 ，只有一个RAR压缩包

zhansb

烟云龙紫 发表于 2015-4-15 17:36
这个是SDK目录下的东西吗，我的SDK下没有这个目录的文件 ，只有一个RAR压缩包

SDK更新一下

shf1986

我用的默认版，rk3288-3.10-uboot-android-data1G.parameter.txt跟楼主一样，还是不行......任何东西都没有改过，按官方文档来的就是不行，编译出来的misc.img和resource.img一起烧写，就出起不来的问题了......
楼主有什么高见么？

syjh7370628

同样的问题得到解决，:lol不过我用Android开发工具v2.35，没办法打包成update.img,求助一下！！！:$

firefly001

同样，这个2.35用不了