求助：firefly3288 android5.1 HDMI无输出，没显示

yubang · 发表于 2016-10-21 10:21:11

本帖最后由 yubang 于 2016-10-21 10:21 编辑

各位好，
我在firefly3288上运行android5.1（firefly百度网盘下载的源码）的代码；代码中原来是支持vga和hdmi的；

我对代码进行了改动，将vga的支持去掉，只用 hdmi；
改动后，重新编译，更新各个映像；
现在板子能够正常启动进入到系统命令行，插入hdmi，能够检测到（检测到720P  60HZ），但是却没有显示；

查看内核的启动log，发现与hdmi相关的都是正常的；

请教各位，为什么这样呢？是不是我的改动哪里没有完成？
（我做的改动包括两个地方：
1）把dst文件与vga相关的去掉；
2）内核中把firefly vga的配置去掉；
)

以下是内核的log：（与hdmi相关的部分）
[ 0.000000] rkclk_init_clks: cnt_parent = 7
[ 0.000000] rkclk_init_clks: cnt_rate = 28
[ 0.000000] rk3288 set GPLL BW 20 for HDMI!
[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).

[ 1.045890] bio: create slab <bio-0> at 0
[ 1.046391] Rockchip hdmi driver version 2.0

[ 1.433560] io scheduler cfq registered (default)
[ 1.434770] rockchip-hdmiv2 ff980000.hdmi: rockchip hdmiv2 probe sucess.
[ 1.435470] IEP Driver loaded succesfully

[ 1.487524] hdmi->edidread:1

[ 1.583893] hdmi output corlor mode is 3
[ 1.583910] hdmi connect to lcdc1
[ 1.583922] switch:en=1,lcdc_id=1,screen type=6,cur type=0

[ 1.769686] rockchip-spdif-card rockchip-spdif-card.25:  rk-hdmi-spdif-hifi <-> ff880000.rockchip-spdif mapping ok
[ 1.770247] rockchip-es8323 rockchip-es8323.27: ASoC: CODEC (null) not registered

[ 1.832979] pixel clk is 74250000 tmds clk is 74250000
[ 1.833025] rockchip-hdmiv2 ff980000.hdmi: [hdmi_dev_config_video] sucess output HDMI.

拔掉hdmi线的内核打印：
[  211.542986] hdmi remove from lcdc1
[  211.542999] switch:en=0,lcdc_id=1,screen type=6,cur type=6
[  211.798823] rk_fb_switch_screen: wait update_regs_wait timeout
[  211.798863] rk3288-lcdc lcdc1: no layer is used,go to standby!

重新插入hdmi线的内核打印：
#
# [  219.660993] --11
[  219.708901] hdmi->edidread:1
[  219.804712] hdmi output corlor mode is 3
[  219.804726] hdmi connect to lcdc1
[  219.804733] switch:en=1,lcdc_id=1,screen type=6,cur type=6
[  220.054589] rk_fb_switch_screen: wait update_regs_wait timeout
[  220.054606] rk3288_load_screen,clk_on = 0
[  220.054641] rk3288-lcdc lcdc1: lcdc1: dclk:74250000>>fps:60
[  220.054650] rk3288-lcdc lcdc1: wakeup from standby!
[  220.153120] pixel clk is 74250000 tmds clk is 74250000
[  220.153173] rockchip-hdmiv2 ff980000.hdmi: [hdmi_dev_config_video] sucess output HDMI.

请教各位，这样的情况下hdmi没输出，可能是哪方面的问题呀？
  （所用的hdmi显示器应该是没问题的，这个可以排除；而板子，hdmi应该也没问题，这么简单的电路）

谢谢；

madman · 发表于 2016-10-21 15:21:03

去rk3288.dtsi 把hdmi改成lcdc0应该就好了

jpchen · 发表于 2016-10-21 15:32:01

请同步代码到最新，然后在最新版本上修改看看

yubang · 发表于 2016-10-21 23:30:29

madman 发表于 2016-10-21 15:21
去rk3288.dtsi 把hdmi改成lcdc0应该就好了

谢谢！
我看了rk3288.dtsi 这个文件，里面跟hdmi相关的部分是：
hdmi: hdmi@ff980000 {
compatible = "rockchip,rk3288-hdmi";
reg = <0xff980000 0x20000>;
interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c5_sda &i2c5_scl>;
pinctrl-1 = <&i2c5_gpio>;
clocks = <&clk_gates16 9>, <&clk_gates5 12>;
clock-names = "pclk_hdmi", "hdcp_clk_hdmi";
status = "disabled";
};

lcdc0: lcdc@ff930000 {
compatible = "rockchip,rk3288-lcdc";
rockchip,prop = <PRMRY>;
rockchip,pwr18 = <0>;
rockchip,iommu-enabled = <0>;
reg = <0xff930000 0x10000>;
interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&lcdc0_lcdc>;
pinctrl-1 = <&lcdc0_gpio>;
status = "disabled";
clocks = <&clk_gates15 5>, <&dclk_lcdc0>, <&clk_gates15 6>, <&pd_vop0>;
clock-names = "aclk_lcdc", "dclk_lcdc", "hclk_lcdc", "pd_lcdc";
};

lcdc1: lcdc@ff940000 {
compatible = "rockchip,rk3288-lcdc";
rockchip,prop = <EXTEND>;
rockchip,pwr18 = <0>;
rockchip,iommu-enabled = <0>;
reg = <0xff940000 0x10000>;
interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
clocks = <&clk_gates15 7>, <&dclk_lcdc1>, <&clk_gates15 8>, <&pd_vop1>;
clock-names = "aclk_lcdc", "dclk_lcdc", "hclk_lcdc", "pd_lcdc";
};

不知道你提到的hdmi 改成 lcdc0，是指哪处？

因为刚接触3288，很多不了解，望不吝指教，谢谢！

yubang · 发表于 2016-10-21 23:31:21

madman 发表于 2016-10-21 15:21
去rk3288.dtsi 把hdmi改成lcdc0应该就好了

谢谢！
我看了rk3288.dtsi 这个文件，里面跟hdmi相关的部分是：
hdmi: hdmi@ff980000 {
compatible = "rockchip,rk3288-hdmi";
reg = <0xff980000 0x20000>;
interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c5_sda &i2c5_scl>;
pinctrl-1 = <&i2c5_gpio>;
clocks = <&clk_gates16 9>, <&clk_gates5 12>;
clock-names = "pclk_hdmi", "hdcp_clk_hdmi";
status = "disabled";
};

lcdc0: lcdc@ff930000 {
compatible = "rockchip,rk3288-lcdc";
rockchip,prop = <PRMRY>;
rockchip,pwr18 = <0>;
rockchip,iommu-enabled = <0>;
reg = <0xff930000 0x10000>;
interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&lcdc0_lcdc>;
pinctrl-1 = <&lcdc0_gpio>;
status = "disabled";
clocks = <&clk_gates15 5>, <&dclk_lcdc0>, <&clk_gates15 6>, <&pd_vop0>;
clock-names = "aclk_lcdc", "dclk_lcdc", "hclk_lcdc", "pd_lcdc";
};

lcdc1: lcdc@ff940000 {
compatible = "rockchip,rk3288-lcdc";
rockchip,prop = <EXTEND>;
rockchip,pwr18 = <0>;
rockchip,iommu-enabled = <0>;
reg = <0xff940000 0x10000>;
interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
clocks = <&clk_gates15 7>, <&dclk_lcdc1>, <&clk_gates15 8>, <&pd_vop1>;
clock-names = "aclk_lcdc", "dclk_lcdc", "hclk_lcdc", "pd_lcdc";
};

不知道你提到的hdmi 改成 lcdc0，是指哪处？

因为刚接触3288，很多不了解，望不吝指教，谢谢！

yubang · 发表于 2016-10-21 23:33:38

jpchen 发表于 2016-10-21 15:32
请同步代码到最新，然后在最新版本上修改看看

谢谢！

从网盘下载了代码后，我同步过一次，那时代码应该是更新到2016年7月份的；是否这两三个月的更新，有和我遇到的这个问题相关的呢？

刚接触3288，望不吝指教，谢谢！

yubang · 发表于 2016-10-22 10:17:53

jpchen 发表于 2016-10-21 15:32
请同步代码到最新，然后在最新版本上修改看看

我确认了一下，我的代码同步到2016年，8月9日的；

jpchen · 发表于 2016-10-24 11:47:49

yubang 发表于 2016-10-22 10:17
我确认了一下，我的代码同步到2016年，8月9日的；

请烧录官方固件试试，确定是否是可以，如果可以可排除是硬件问题，

（）大鹏 · 发表于 2021-5-27 22:32:10

楼主解决了吗？