|
【技术讨论】
rk3399 长时间无法启动
发表于 2019-3-18 14:15:25
浏览:16901
|
回复:6
打印
只看该作者
[复制链接]
楼主
启动log如下所示:- #Boot ver: 2019-02-17#1.09
- empty serial no.
- normal boot.
- checkKey
- vbus = 0
- board_fbt_key_pressed: ir_keycode = 0x0, frt = 0
- no fuel gauge found
- no fuel gauge found
- failed to find phy node
- failed to find panel driver
- read logo on state from dts [1]
- no fuel gauge found
- can't find dts node for deviceinfo
- dw_rk_hdmi_register:fail to read deviceinfo
- hdmi baseparamer 0x0@0-0
- [EDID-EXTEND] It is a CEA 861 Series Extension.
- no baseparametr,find best edid mode,vic=16
- hdmi_dev->video.vic is 4
- rk lcdc - 0 dclk set: dclk = 74250000HZ, pll select = 0, div = 1
- rockchip_panel_prepare: failed to find panel prepare funcs
- hdmi_dev_config_video vic 4 color_output 3 color_output_depth 8
- pixel clk is 74250000 tmds clk is 74250000
- hsync_pol 1 vsync_pol 1
- [HDMI] sucess output HDMI.
- PHY PLL not locked: PCLK_ON=1,TMDSCLK_ON=0
- rockchip_panel_enable: failed to find panel prepare funcs
- ERROR: [get_entry_ram]: Cannot find logo_kernel.bmp!
- failed to display kernel logo
- checkKey
- vbus = 0
- board_fbt_key_pressed: ir_keycode = 0x0, frt = 0
- Hit any key to stop autoboot: 0
- load fdt from resouce.
- vendor read error!
- Set oem_unlocked=0Secure Boot state: 0
- kernel @ 0x00280000 (0x01248008)
- ramdisk @ 0x04bf0000 (0x001ad5d8)
- bootrk: do_bootm_linux...
- Loading Device Tree to 0000000004600000, end 00000000046164f0 ... OK
- Add bank:0000000000200000, 0000000008200000
- Add bank:000000000a200000, 00000000ede00000
- WARNING: could not set reg FDT_ERR_BADOFFSET.
- Starting kernel ...
- [ 0.000000] Booting Linux on physical CPU 0x0
- [ 0.000000] Initializing cgroup subsys cpuset
- [ 0.000000] Initializing cgroup subsys cpu
- [ 0.000000] Initializing cgroup subsys cpuacct
- [ 0.000000] Initializing cgroup subsys schedtune
- [ 0.000000] Linux version 4.4.103 (zhang@zhang-Inspiron-5577) (gcc version 4.9 20150123 (prerelease) (GCC) ) #10 SMP PREEMPT Wed Mar 6 15:07:30 CST 2019
- [ 0.000000] Boot CPU: AArch64 Processor [410fd034]
- [ 0.000000] earlycon: Early serial console at MMIO32 0xff1a0000 (options '')
- [ 0.000000] bootconsole [uart0] enabled
- [ 0.000000] hdmi init vic is -1
- [ 0.000000] Reserved memory: failed to reserve memory for node 'stb-devinfo@00000000': base 0x0000000000000000, size 0 MiB
- [ 0.000000] cma: Reserved 16 MiB at 0x00000000f7000000
- [ 0.000000] psci: probing for conduit method from DT.
- [ 0.000000] psci: PSCIv1.0 detected in firmware.
- [ 0.000000] psci: Using standard PSCI v0.2 function IDs
- [ 0.000000] psci: Trusted OS migration not required
- [ 0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc0f6eed000 s45504 r8192 d32320 u86016
- [ 0.000000] Detected VIPT I-cache on CPU0
- [ 0.000000] CPU features: enabling workaround for ARM erratum 845719
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 991752
- [ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0xff1a0000 swiotlb=1 androidboot.baseband=N/A androidboot.selinux=permissive androidboot.hardware=rk30boar0
- [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
- [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
- [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
- [ 0.000000] software IO TLB [mem 0xf6ea4000-0xf6ee4000] (0MB) mapped at [ffffffc0f6ea4000-ffffffc0f6ee3fff]
- [ 0.000000] Memory: 3918852K/4030464K available (10942K kernel code, 1632K rwdata, 5264K rodata, 832K init, 1073K bss, 95228K reserved, 16384K cma-reserved)
- [ 0.000000] Virtual kernel memory layout:
- [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
- [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000 ( 246 GB)
- [ 0.000000] .init : 0xffffff8009060000 - 0xffffff8009130000 ( 832 KB)
- [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008b30000 ( 10944 KB)
- [ 0.000000] .rodata : 0xffffff8008b30000 - 0xffffff8009060000 ( 5312 KB)
- [ 0.000000] .data : 0xffffff8009130000 - 0xffffff80092c8008 ( 1633 KB)
- [ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum)
- [ 0.000000] 0xffffffbdc0008000 - 0xffffffbdc3e00000 ( 61 MB actual)
- [ 0.000000] fixed : 0xffffffbffe7fd000 - 0xffffffbffec00000 ( 4108 KB)
- [ 0.000000] PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000 ( 16 MB)
- [ 0.000000] memory : 0xffffffc000200000 - 0xffffffc0f8000000 ( 3966 MB)
- [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
- [ 0.000000] Preemptible hierarchical RCU implementation.
- [ 0.000000] Build-time adjustment of leaf fanout to 64.
- [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
- [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6
- [ 0.000000] NR_IRQS:64 nr_irqs:64 0
- [ 0.000000] GIC: Using split EOI/Deactivate mode
- [ 0.000000] ITS: /interrupt-controller@fee00000/interrupt-controller@fee20000
- [ 0.000000] ITS: allocated 65536 Devices @a200000 (psz 64K, shr 0)
- [ 0.000000] ITS: using cache flushing for cmd queue
- [ 0.000000] GIC: using LPI property table @0x000000000a280000
- [ 0.000000] ITS: Allocated 1792 chunks for LPIs
- [ 0.000000] CPU0: found redistributor 0 region 0:0x00000000fef00000
- [ 0.000000] CPU0: using LPI pending table @0x000000000a290000
- [ 0.000000] GIC: using cache flushing for LPI property table
- [ 0.000000] GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
- [ 0.000000] GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
- [ 0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop0_frac as parent of dclk_vop0, rate changes may not work
- [ 0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop1_frac as parent of dclk_vop1, rate changes may not work
- [ 0.000000] rockchip_cpuclk_pre_rate_change: limiting alt-divider 33 to 31
- [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
- [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
- [ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
- [ 0.001930] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
- [ 0.002894] pid_max: default: 32768 minimum: 301
- [ 0.003410] Security Framework initialized
- [ 0.003800] SELinux: Initializing.
- [ 0.004213] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
- [ 0.004843] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
- [ 0.006339] Initializing cgroup subsys freezer
- [ 0.006768] Initializing cgroup subsys debug
- [ 0.008060] sched-energy: Sched-energy-costs installed from DT
- [ 0.008610] CPU0: update cpu_capacity 401
- [ 0.009064] ASID allocator initialised with 65536 entries
- [ 0.025884] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
- [ 0.027138] Platform MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
- [ 0.039285] Detected VIPT I-cache on CPU1
- [ 0.039317] CPU1: found redistributor 1 region 0:0x00000000fef20000
- [ 0.039357] CPU1: using LPI pending table @0x00000000f1c00000
- [ 0.039399] CPU1: update cpu_capacity 401
- [ 0.039402] CPU1: Booted secondary processor [410fd034]
- [ 0.049280] Detected VIPT I-cache on CPU2
- [ 0.049299] CPU2: found redistributor 2 region 0:0x00000000fef40000
- [ 0.049331] CPU2: using LPI pending table @0x00000000f1c30000
- [ 0.049359] CPU2: update cpu_capacity 401
- [ 0.049362] CPU2: Booted secondary processor [410fd034]
- [ 0.059318] Detected VIPT I-cache on CPU3
- [ 0.059336] CPU3: found redistributor 3 region 0:0x00000000fef60000
- [ 0.059368] CPU3: using LPI pending table @0x00000000f1c70000
- [ 0.059395] CPU3: update cpu_capacity 401
- [ 0.059398] CPU3: Booted secondary processor [410fd034]
- [ 0.069366] Detected PIPT I-cache on CPU4
- [ 0.069395] CPU4: found redistributor 100 region 0:0x00000000fef80000
- [ 0.069435] CPU4: using LPI pending table @0x00000000f1cb0000
- [ 0.069475] CPU4: update cpu_capacity 1024
- [ 0.069479] CPU4: Booted secondary processor [410fd082]
- [ 0.079386] Detected PIPT I-cache on CPU5
- [ 0.079404] CPU5: found redistributor 101 region 0:0x00000000fefa0000
- [ 0.079440] CPU5: using LPI pending table @0x00000000f1cf0000
- [ 0.079468] CPU5: update cpu_capacity 1024
- [ 0.079471] CPU5: Booted secondary processor [410fd082]
- [ 0.079555] Brought up 6 CPUs
- [ 0.091660] SMP: Total of 6 processors activated.
- [ 0.092104] CPU features: detected feature: GIC system register CPU interface
- [ 0.092775] CPU: All CPU(s) started at EL2
- [ 0.093195] alternatives: patching kernel code
- [ 0.095279] devtmpfs: initialized
- [ 0.115593] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
- [ 0.116568] futex hash table entries: 2048 (order: 5, 131072 bytes)
- [ 0.117893] pinctrl core: initialized pinctrl subsystem
- [ 0.119960] Failed to find legacy iommu devices
- [ 0.120774] NET: Registered protocol family 16
- [ 0.121551] schedtune: init normalization constants...
- [ 0.122055] schedtune: CLUSTER[0-3] min_pwr: 56 max_pwr: 222
- [ 0.122689] schedtune: CPU[0] min_pwr: 0 max_pwr: 222
- [ 0.123335] schedtune: CPU[1] min_pwr: 0 max_pwr: 222
- [ 0.123968] schedtune: CPU[2] min_pwr: 0 max_pwr: 222
- [ 0.124601] schedtune: CPU[3] min_pwr: 0 max_pwr: 222
- [ 0.125234] schedtune: CLUSTER[4-5] min_pwr: 65 max_pwr: 1108
- [ 0.125866] schedtune: CPU[4] min_pwr: 0 max_pwr: 1108
- [ 0.126499] schedtune: CPU[5] min_pwr: 0 max_pwr: 1108
- [ 0.127158] schedtune: SYSTEM min_pwr: 121 max_pwr: 4434
- [ 0.127791] schedtune: using normalization constants mul: 3862781856 sh1: 1 sh2: 12
- [ 0.128530] schedtune: verify normalization constants...
- [ 0.129046] schedtune: max_pwr/2^0: 4313 => norm_pwr: 1024
- [ 0.129586] schedtune: max_pwr/2^1: 2156 => norm_pwr: 511
- [ 0.130125] schedtune: max_pwr/2^2: 1078 => norm_pwr: 255
- [ 0.130672] schedtune: max_pwr/2^3: 539 => norm_pwr: 127
- [ 0.131212] schedtune: max_pwr/2^4: 269 => norm_pwr: 63
- [ 0.131751] schedtune: max_pwr/2^5: 134 => norm_pwr: 31
- [ 0.132291] schedtune: configured to support 5 boost groups
- [ 0.140707] cpuidle: using governor ladder
- [ 0.150712] cpuidle: using governor menu
- [ 0.151105] Registered FIQ tty driver
- [ 0.151781] vdso: 2 pages (1 code @ ffffff8008b36000, 1 data @ ffffff8009134000)
- [ 0.152519] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
- [ 0.153899] DMA: preallocated 256 KiB pool for atomic allocations
- [ 0.175572] console [pstore0] enabled
- [ 0.176162] pstore: Registered ramoops as persistent store backend
- [ 0.176765] ramoops: attached 0xf0000@0x110000, ecc: 0/0
- [ 0.179537] fiq debugger fiq mode enabled
- [[ 0.180201] console [ttyFIQ0] enabled
- 0.180201] console [ttyFIQ0] enabled
- [[ 0.180893] bootconsole [uart0] disabled
- 0.180893] bootconsole [uart0] disabled
- [ 0.181820] Registered fiq debugger ttyFIQ0
- [ 0.212699] Rockchip hdmi driver version 2.0
- .
- [ 0.214955] iommu: Adding device ff650000.vpu_service to group 0
- [ 0.215059] iommu: Adding device ff660000.rkvdec to group 1
- [ 0.215130] iommu: Adding device ff670000.iep to group 2
- [ 0.215224] iommu: Adding device ff8f0000.vop to group 3
- [ 0.215301] iommu: Adding device ff900000.vop to group 4
- [ 0.215407] iommu: Adding device ff910000.isp to group 5
- [ 0.215483] iommu: Adding device ff920000.isp to group 6
- [ 0.216171] rk_iommu ff670800.iommu: can't get aclk
- [ 0.216191] rk_iommu ff670800.iommu: can't get hclk
- [ 0.217062] SCSI subsystem initialized
- [ 0.217391] usbcore: registered new interface driver usbfs
- [ 0.217437] usbcore: registered new interface driver hub
- [ 0.217512] usbcore: registered new device driver usb
- [ 0.217874] media: Linux media interface: v0.10
- [ 0.217914] Linux video capture interface: v2.00
- [ 0.218045] pps_core: LinuxPPS API ver. 1 registered
- [ 0.218056] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
- [ 0.218082] PTP clock support registered
- [ 0.219621] Advanced Linux Sound Architecture Driver Initialized.
- [ 0.220091] Bluetooth: Core ver 2.21
- [ 0.220145] NET: Registered protocol family 31
- [ 0.220157] Bluetooth: HCI device and connection manager initialized
- [ 0.220173] Bluetooth: HCI socket layer initialized
- [ 0.220187] Bluetooth: L2CAP socket layer initialized
- [ 0.220216] Bluetooth: SCO socket layer initialized
- [ 0.221288] rockchip-cpuinfo cpuinfo: Serial : 88ff02704c5b8ce7
- [ 0.221773] clocksource: Switched to clocksource arch_sys_counter
- [ 0.265005] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
- [ 0.265267] NET: Registered protocol family 2
- [ 0.265685] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
- [ 0.265868] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
- [ 0.266097] TCP: Hash tables configured (established 32768 bind 32768)
- [ 0.266176] UDP hash table entries: 2048 (order: 4, 65536 bytes)
- [ 0.266222] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
- [ 0.266397] NET: Registered protocol family 1
- [ 0.266902] Trying to unpack rootfs image as initramfs...
- [ 0.355373] Freeing initrd memory: 1716K
- [ 0.355879] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
- [ 0.355969] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
- [ 0.358623] audit: initializing netlink subsys (disabled)
- [ 0.358707] audit: type=2000 audit(0.356:1): initialized
- [ 0.363934] VFS: Disk quotas dquot_6.6.0
- [ 0.364072] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
- [ 0.365633] fuse init (API version 7.23)
- [ 0.366832]
- [ 0.366832] TEE Core Framework initialization (ver 1:0.1)
- [ 0.366867] TEE armv7 Driver initialization
- [ 0.367220] tz_tee_probe: name="armv7sec", id=0, pdev_name="armv7sec.0"
- [ 0.367237] TEE core: Alloc the misc device "opteearmtz00" (id=0)
- [ 0.367420] TEE Core: Register the misc device "opteearmtz00" (id=0,minor=62)
- [ 0.371332] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
- [ 0.371362] io scheduler noop registered
- [ 0.371531] io scheduler cfq registered (default)
- [ 0.372874] rockchip-usb2phy ff770000.syscon:usb2-phy@e460: vbus_drv is not assigned
- [ 0.377865] rockchip-pcie f8000000.pcie: no vpcie3v3 regulator found
- [ 0.377897] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found
- [ 0.377916] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found
- [ 0.898539] rockchip-pcie f8000000.pcie: PCIe link training gen1 timeout!
- [ 0.898716] rockchip-pcie: probe of f8000000.pcie failed with error -110
- [ 0.900087] iep: failed to find iep power down clock source.
- [ 0.900699] IEP Power ON
- [ 0.900912] IEP Power OFF
- [ 0.900997] IEP Driver loaded succesfully
- [ 0.901231] Module initialized.
- [ 0.901842] rk-vcodec ff650000.vpu_service: probe device
- [ 0.901889] rk-vcodec ff650000.vpu_service: vpu mmu dec ffffffc0f1f0a410
- [ 0.902062] rk-vcodec ff650000.vpu_service: allocator is drm
- [ 0.902126] rk-vcodec ff650000.vpu_service: checking hw id 0
- [ 0.902719] rk-vcodec ff650000.vpu_service: init success
- [ 0.905857] rk-vcodec ff660000.rkvdec: probe device
- [ 0.906348] rk-vcodec ff660000.rkvdec: vpu mmu dec ffffffc0f1f0ac10
- [ 0.907046] rk-vcodec ff660000.rkvdec: allocator is drm
- [ 0.907574] rk-vcodec ff660000.rkvdec: checking hw id 6876
- [ 0.908379] rk-vcodec ff660000.rkvdec: init success
- [ 0.910259] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
- [ 0.910953] dma-pl330 ff6d0000.dma-controller: DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
- [ 0.913086] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
- [ 0.913786] dma-pl330 ff6e0000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
- [ 0.916204] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled
- [ 0.918352] console [ttyS0] disabled
- [ 0.918722] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 36, base_baud = 1500000) is a 16550A
- [ 0.920056] ff1a0000.serial: ttyS2 at MMIO 0xff1a0000 (irq = 37, base_baud = 1500000) is a 16550A
- [ 0.921417] ff370000.serial: ttyS4 at MMIO 0xff370000 (irq = 40, base_baud = 1500000) is a 16550A
- [ 0.922582] [drm:drm_core_init] Initialized drm 1.1.0 20060810
- [ 0.928008] mali ff9a0000.gpu: Failed to get regulator
- [ 0.928489] mali ff9a0000.gpu: Power control initialization failed
- [ 0.929329] Unable to detect cache hierarchy from DT for CPU 0
- [ 0.939386] brd: module loaded
- [ 0.945542] loop: module loaded
- [ 0.946209] zram: Added device: zram0
- [ 0.947132] SCSI Media Changer driver v0.25
- [ 0.948693] rockchip-pinctrl pinctrl: pin gpio1-8 already requested by ff370000.serial; cannot claim for ff1d0000.spi
- [ 0.948721] rockchip-pinctrl pinctrl: pin-40 (ff1d0000.spi) status -22
- [ 0.948742] rockchip-pinctrl pinctrl: could not request pin 40 (gpio1-8) from group spi1-tx on device rockchip-pinctrl
- [ 0.948766] rockchip-spi ff1d0000.spi: Error applying setting, reverse things back
- [ 0.948900] rockchip-spi ff1d0000.spi: Failed to request TX DMA channel
- [ 0.948914] rockchip-spi ff1d0000.spi: Failed to request RX DMA channel
- [ 0.949591] register spi return v = :0
- [ 0.949643] tun: Universal TUN/TAP device driver, 1.6
- [ 0.949654] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
- [ 0.950573] force_sf_dma_mode is ignored if force_thresh_dma_mode is set.
- [ 0.950661] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
- [ 0.950679] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
- [ 0.950693] rk_gmac-dwmac fe300000.ethernet: RX delay(0x1b).
- [ 0.950718] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
- [ 0.950891] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
- [ 0.955909] rk_gmac-dwmac fe300000.ethernet: init for RGMII
- [ 0.956040] stmmac - user ID: 0x10, Synopsys ID: 0x35
- [ 0.956050] Ring mode enabled
- [ 0.956059] DMA HW capability register supported
- [ 0.956068] Normal descriptors
- [ 0.956078] RX Checksum Offload Engine supported (type 2)
- [ 0.956088] Wake-Up On Lan supported
- [ 0.956130] Enable RX Mitigation via HW Watchdog Timer
- [ 1.024739] libphy: stmmac: probed
- [ 1.024796] eth%d: PHY ID 001cc915 at 0 IRQ POLL (stmmac-0:00) active
- [ 1.024811] eth%d: PHY ID 001cc915 at 1 IRQ POLL (stmmac-0:01)
- [ 1.026227] PPP generic driver version 2.4.2
- [ 1.026533] PPP BSD Compression module registered
- [ 1.026550] PPP Deflate Compression module registered
- [ 1.026585] PPP MPPE Compression module registered
- [ 1.026606] NET: Registered protocol family 24
- [ 1.026657] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
- [ 1.026702] CSLIP: code copyright 1989 Regents of the University of California.
- [ 1.026731] Rockchip WiFi SYS interface (V1.00) ...
- [ 1.026855] usbcore: registered new interface driver catc
- [ 1.026912] usbcore: registered new interface driver kaweth
- [ 1.026930] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
- [ 1.026985] usbcore: registered new interface driver pegasus
- [ 1.027042] usbcore: registered new interface driver rtl8150
- [ 1.027098] usbcore: registered new interface driver r8152
- [ 1.027113] hso: drivers/net/usb/hso.c: Option Wireless
- [ 1.027188] usbcore: registered new interface driver hso
- [ 1.027255] usbcore: registered new interface driver asix
- [ 1.027312] usbcore: registered new interface driver ax88179_178a
- [ 1.027368] usbcore: registered new interface driver cdc_ether
- [ 1.027424] usbcore: registered new interface driver cdc_eem
- [ 1.027478] usbcore: registered new interface driver dm9601
- [ 1.027553] usbcore: registered new interface driver smsc75xx
- [ 1.027620] usbcore: registered new interface driver smsc95xx
- [ 1.027676] usbcore: registered new interface driver gl620a
- [ 1.027731] usbcore: registered new interface driver net1080
- [ 1.027786] usbcore: registered new interface driver plusb
- [ 1.027842] usbcore: registered new interface driver rndis_host
- [ 1.027902] usbcore: registered new interface driver cdc_subset
- [ 1.027957] usbcore: registered new interface driver zaurus
- [ 1.028015] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
- [ 1.028096] usbcore: registered new interface driver int51x1
- [ 1.028153] usbcore: registered new interface driver kalmia
- [ 1.028214] usbcore: registered new interface driver ipheth
- [ 1.028273] usbcore: registered new interface driver sierra_net
- [ 1.028330] usbcore: registered new interface driver cx82310_eth
- [ 1.028399] usbcore: registered new interface driver cdc_ncm
- [ 1.028477] usbcore: registered new interface driver qmi_wwan
- [ 1.028541] usbcore: registered new interface driver cdc_mbim
- [ 1.030291] rockchip-dwc3 usb@fe800000: failed to get drvdata dwc3
- [ 1.035131] rockchip-dwc3 usb@fe900000: fail to get drvdata hcd
- [ 1.036040] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 1.036061] ehci-pci: EHCI PCI platform driver
- [ 1.036151] ehci-platform: EHCI generic platform driver
- [ 1.040169] ehci-platform fe3c0000.usb: EHCI Host Controller
- [ 1.040206] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 1
- [ 1.040441] ehci-platform fe3c0000.usb: irq 30, io mem 0xfe3c0000
- [ 1.048463] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
- [ 1.048655] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
- [ 1.048672] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 1.048686] usb usb1: Product: EHCI Host Controller
- [ 1.048698] usb usb1: Manufacturer: Linux 4.4.103 ehci_hcd
- [ 1.048711] usb usb1: SerialNumber: fe3c0000.usb
- [ 1.049366] hub 1-0:1.0: USB hub found
- [ 1.049408] hub 1-0:1.0: 1 port detected
- [ 1.050211] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 1.050258] ohci-platform: OHCI generic platform driver
- [ 1.050887] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
- [ 1.050920] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 2
- [ 1.051106] ohci-platform fe3e0000.usb: irq 31, io mem 0xfe3e0000
- [ 1.105980] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
- [ 1.106036] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 1.106053] usb usb2: Product: Generic Platform OHCI controller
- [ 1.106067] usb usb2: Manufacturer: Linux 4.4.103 ohci_hcd
- [ 1.106081] usb usb2: SerialNumber: fe3e0000.usb
- [ 1.106692] hub 2-0:1.0: USB hub found
- [ 1.106734] hub 2-0:1.0: 1 port detected
- [ 1.108052] usbcore: registered new interface driver cdc_acm
- [ 1.108064] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
- [ 1.108148] usbcore: registered new interface driver usblp
- [ 1.108211] usbcore: registered new interface driver cdc_wdm
- [ 1.108274] usbcore: registered new interface driver uas
- [ 1.108382] usbcore: registered new interface driver usb-storage
- [ 1.108521] usbcore: registered new interface driver ums-alauda
- [ 1.108581] usbcore: registered new interface driver ums-cypress
- [ 1.108645] usbcore: registered new interface driver ums-datafab
- [ 1.108701] usbcore: registered new interface driver ums_eneub6250
- [ 1.108757] usbcore: registered new interface driver ums-freecom
- [ 1.108812] usbcore: registered new interface driver ums-isd200
- [ 1.108868] usbcore: registered new interface driver ums-jumpshot
- [ 1.108923] usbcore: registered new interface driver ums-karma
- [ 1.108980] usbcore: registered new interface driver ums-onetouch
- [ 1.109036] usbcore: registered new interface driver ums-sddr09
- [ 1.109091] usbcore: registered new interface driver ums-sddr55
- [ 1.109150] usbcore: registered new interface driver ums-usbat
- [ 1.109260] usbcore: registered new interface driver usbserial
- [ 1.109309] usbcore: registered new interface driver usbserial_generic
- [ 1.109348] usbserial: USB Serial support registered for generic
- [ 1.109406] usbcore: registered new interface driver ch341
- [ 1.109444] usbserial: USB Serial support registered for ch341-uart
- [ 1.109506] usbcore: registered new interface driver cp210x
- [ 1.109544] usbserial: USB Serial support registered for cp210x
- [ 1.109621] usbcore: registered new interface driver ftdi_sio
- [ 1.109658] usbserial: USB Serial support registered for FTDI USB Serial Device
- [ 1.109816] usbcore: registered new interface driver option
- [ 1.109853] usbserial: USB Serial support registered for GSM modem (1-port)
- [ 1.110020] usbcore: registered new interface driver pl2303
- [ 1.110057] usbserial: USB Serial support registered for pl2303
- [ 1.110129] usbcore: registered new interface driver trancevibrator
- [ 1.110149] usb20_otg: version 3.10a 21-DEC-2012
- [ 1.110431] usb20_host: version 3.10a 21-DEC-2012
- [ 1.111094] usbcore: registered new interface driver xpad
- [ 1.111167] usbcore: registered new interface driver usb_acecad
- [ 1.111231] usbcore: registered new interface driver aiptek
- [ 1.111293] usbcore: registered new interface driver gtco
- [ 1.111355] usbcore: registered new interface driver hanwang
- [ 1.111417] usbcore: registered new interface driver kbtab
- [ 1.111434] ==gsl_ts_init==
- [ 1.111473] ret=0
- [ 1.112075] .. rk pwm remotectl v1.1 init
- [ 1.112398] input: ff420030.pwm as /devices/platform/ff420030.pwm/input/input0
- [ 1.113036] sensor_register_slave:mma8452,id=17
- [ 1.113056] sensor_register_slave:lis3dh,id=7
- [ 1.113074] sensor_register_slave:mma7660,id=18
- [ 1.113091] sensor_register_slave:lsm303d,id=22
- [ 1.113108] sensor_register_slave:gs_mc3230,id=23
- [ 1.113117] [Gsensor] gsensor_init
- [ 1.113133] sensor_register_slave:mpu6880_acc,id=24
- [ 1.113151] sensor_register_slave:mpu6500_acc,id=25
- [ 1.113168] sensor_register_slave:lsm330_acc,id=26
- [ 1.113186] sensor_register_slave:akm8975,id=29
- [ 1.113203] sensor_register_slave:akm8963,id=30
- [ 1.113221] sensor_register_slave:l3g4200d,id=44
- [ 1.113238] sensor_register_slave:l3g20d,id=45
- [ 1.113255] sensor_register_slave:ewtsa,id=46
- [ 1.113272] sensor_register_slave:lsm330_gyro,id=50
- [ 1.113289] sensor_register_slave:cm3217,id=52
- [ 1.113306] sensor_register_slave:cm3218,id=53
- [ 1.114240] i2c /dev entries driver
- [ 1.115741] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
- [ 1.115847] fan53555-reg: supplied by vcc5v0_sys
- [ 1.117742] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected!
- [ 1.117809] fan53555-reg: supplied by vcc5v0_sys
- [ 1.119904] rk808 0-001b: Pmic Chip id: 0x0
- [ 1.123617] rk808-regulator rk808-regulator: there is no dvs0 gpio
- [ 1.123694] rk808-regulator rk808-regulator: there is no dvs1 gpio
- [ 1.123811] DCDC_REG1: supplied by vcc3v3_sys
- [ 1.124612] DCDC_REG2: supplied by vcc3v3_sys
- [ 1.125296] DCDC_REG3: supplied by vcc3v3_sys
- [ 1.125570] DCDC_REG4: supplied by vcc3v3_sys
- [ 1.126031] LDO_REG1: supplied by vcc3v3_sys
- [ 1.127241] LDO_REG2: supplied by vcc3v3_sys
- [ 1.128256] LDO_REG3: supplied by vcc3v3_sys
- [ 1.129251] LDO_REG4: supplied by vcc3v3_sys
- [ 1.130274] LDO_REG5: supplied by vcc3v3_sys
- [ 1.131261] LDO_REG6: supplied by vcc3v3_sys
- [ 1.132253] LDO_REG7: supplied by vcc3v3_sys
- [ 1.133262] LDO_REG8: supplied by vcc3v3_sys
- [ 1.134289] SWITCH_REG1: supplied by vcc3v3_sys
- [ 1.134569] SWITCH_REG2: supplied by vcc3v3_sys
- [ 1.138337] rk808-rtc rk808-rtc: rtc core: registered rk808-rtc as rtc0
- [ 1.138965] rk3x-i2c ff3c0000.i2c: Initialized RK3xxx I2C bus at ffffff80095fe000
- [ 1.139718] rk3x-i2c ff110000.i2c: Initialized RK3xxx I2C bus at ffffff80096dc000
- [ 1.139842] rockchip-pinctrl pinctrl: pin gpio4-17 already requested by ff940000.hdmi; cannot claim for ff130000.i2c
- [ 1.139860] rockchip-pinctrl pinctrl: pin-145 (ff130000.i2c) status -22
- [ 1.139875] rockchip-pinctrl pinctrl: could not request pin 145 (gpio4-17) from group i2c3-xfer on device rockchip-pinctrl
- [ 1.139891] rk3x-i2c ff130000.i2c: Error applying setting, reverse things back
- [ 1.140326] rk3x-i2c ff130000.i2c: Initialized RK3xxx I2C bus at ffffff80096de000
- [ 1.141899] fusb302 4-0022: Can't get property of role, set role to default DRP
- [ 1.150246] fusb302 4-0022: port 0 probe success with role ROLE_MODE_DRP, try_role ROLE_MODE_NONE
- [ 1.150287] rk3x-i2c ff3d0000.i2c: Initialized RK3xxx I2C bus at ffffff80096f2000
- [ 1.151467] IR NEC protocol handler initialized
- [ 1.151483] IR RC5(x/sz) protocol handler initialized
- [ 1.151498] IR RC6 protocol handler initialized
- [ 1.151513] IR JVC protocol handler initialized
- [ 1.151527] IR Sony protocol handler initialized
- [ 1.151541] IR SANYO protocol handler initialized
- [ 1.151556] IR Sharp protocol handler initialized
- [ 1.151571] IR MCE Keyboard/mouse protocol handler initialized
- [ 1.151586] IR XMP protocol handler initialized
- [ 1.151911] usbcore: registered new interface driver uvcvideo
- [ 1.151922] USB Video Class driver (1.1.1)
- [ 1.151941] CamSys driver version: v0.34.8, CamSys head file version: v0.13.0
- [ 1.157727] __power_supply_register: Expected proper parent device for 'test_ac'
- [ 1.157897] __power_supply_register: Expected proper parent device for 'test_battery'
- [ 1.158217] thermal thermal_zone2: power_allocator: sustainable_power will be estimated
- [ 1.158348] __power_supply_register: Expected proper parent device for 'test_usb'
- [ 1.161656] rk_tsadcv2_temp_to_code: Invalid conversion table: code=1023, temperature=2147483647
- [ 1.162788] device-mapper: uevent: version 1.0.3
- [ 1.163239] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
- [ 1.163446] Bluetooth: HCI UART driver ver 2.3
- [ 1.163460] Bluetooth: HCI UART protocol H4 registered
- [ 1.163471] Bluetooth: HCI UART protocol LL registered
- [ 1.163487] rtk_btusb: RTKBT_RELEASE_NAME: 20170109_TV_ANDROID_6.x
- [ 1.163497] rtk_btusb: Realtek Bluetooth USB driver module init, version 4.1.2
- [ 1.163507] rtk_btusb: Register usb char device interface for BT driver
- [ 1.163848] usbcore: registered new interface driver rtk_btusb
- [ 1.164435] cpu cpu0: leakage=17
- [ 1.181965] cpu cpu0: temp=53888, pvtm=142619 (141827 + 792)
- [ 1.182389] cpu cpu0: pvtm-sel=0
- [ 1.182816] cpu cpu4: leakage=30
- [ 1.195608] cpu cpu4: temp=53333, pvtm=147824 (147404 + 420)
- [ 1.196674] cpu cpu4: pvtm-sel=0
- [ 1.202467] sdhci: Secure Digital Host Controller Interface driver
- [ 1.202518] sdhci: Copyright(c) Pierre Ossman
- [ 1.202537] Synopsys Designware Multimedia Card Interface Driver
- [ 1.203744] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
- [ 1.203893] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
- [ 1.203914] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
- [ 1.203984] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo
- [ 1.204049] dwmmc_rockchip fe310000.dwmmc: 'clock-freq-min-max' property was deprecated.
- [ 1.204110] dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found
- [ 1.204123] dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found
- [ 1.205262] dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode.
- [ 1.205339] dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller.
- [ 1.205359] dwmmc_rockchip fe320000.dwmmc: Version ID is 270a
- [ 1.205411] dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 26,32 bit host data width,256 deep fifo
- [ 1.205437] dwmmc_rockchip fe320000.dwmmc: 'clock-freq-min-max' property was deprecated.
- [ 1.205551] dwmmc_rockchip fe320000.dwmmc: No vmmc regulator found
- [ 1.205884] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000 done
- [ 1.206045] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000 done
- [ 1.218598] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
- [ 1.232879] dwmmc_rockchip fe320000.dwmmc: 1 slots initialized
- [ 1.233156] sdhci-pltfm: SDHCI platform and OF driver helper
- [ 1.234834] sdhci-arasan fe330000.sdhci: No vmmc regulator found
- [ 1.234851] sdhci-arasan fe330000.sdhci: No vqmmc regulator found
- [ 1.262150] mmc1: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA
- [ 1.266139] hidraw: raw HID events driver (C) Jiri Kosina
- [ 1.270906] usbcore: registered new interface driver usbhid
- [ 1.270929] usbhid: USB HID core driver
- [ 1.271103] inv_mpu_iio: inv_mpu_init:746
- [ 1.272712] ashmem: initialized
- [ 1.275343] ff100000.saradc supply vref not found, using dummy regulator
- [ 1.281743] rknandbase v1.1 2016-11-08
- [ 1.282731] usbcore: registered new interface driver snd-usb-audio
- [ 1.284084] rt5640 1-001c: rt5640 have no aux_det_adc_value defined
- [ 1.284159] rt5640 1-001c: Can not read property hp-con-gpio
- [ 1.284172] rt5640 1-001c: Can not read property: linein-mute.
- [ 1.300250] u32 classifier
- [ 1.300276] Actions configured
- [ 1.300341] Netfilter messages via NETLINK v0.30.
- [ 1.300408] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
- [ 1.300796] ctnetlink v0.93: registering with nfnetlink.
- [ 1.301467] xt_time: kernel timezone is -0000
- [ 1.302254] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 1.302429] arp_tables: (C) 2002 David S. Miller
- [ 1.302889] mmc1: MAN_BKOPS_EN bit is not set
- [ 1.302911] Initializing XFRM netlink socket
- [ 1.303351] NET: Registered protocol family 10
- [ 1.307970] mip6: Mobile IPv6
- [ 1.308018] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 1.309523] sit: IPv6 over IPv4 tunneling driver
- [ 1.310001] NET: Registered protocol family 17
- [ 1.310032] NET: Registered protocol family 15
- [ 1.310072] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- [ 1.310894] Bridge firewalling registered
- [ 1.310912] Ebtables v2.0 registered
- [ 1.311133] Bluetooth: RFCOMM TTY layer initialized
- [ 1.311155] Bluetooth: RFCOMM socket layer initialized
- [ 1.311185] Bluetooth: RFCOMM ver 1.11
- [ 1.311213] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
- [ 1.311224] Bluetooth: BNEP filters: protocol multicast
- [ 1.311239] Bluetooth: BNEP socket layer initialized
- [ 1.311257] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
- [ 1.311271] Bluetooth: HIDP socket layer initialized
- [ 1.311318] l2tp_core: L2TP core driver, V2.0
- [ 1.311342] l2tp_ppp: PPPoL2TP kernel driver, V2.0
- [ 1.311360] [WLAN_RFKILL]: Enter rfkill_wlan_init
- [ 1.311642] [WLAN_RFKILL]: Enter rfkill_wlan_probe
- [ 1.311696] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6356s
- [ 1.311708] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
- [ 1.311719] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
- [ 1.311833] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 3, flags = 0.
- [ 1.311845] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
- [ 1.311858] [WLAN_RFKILL]: Exit rfkill_wlan_probe
- [ 1.311920] [BT_RFKILL]: Enter rfkill_rk_init
- [ 1.312263] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 83.
- [ 1.312311] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 9.
- [ 1.312345] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 90.
- [ 1.312379] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 4.
- [ 1.318824] [BT_RFKILL]: Request irq for bt wakeup host
- [ 1.318888] [BT_RFKILL]: ** disable irq
- [ 1.319025] [BT_RFKILL]: bt_default device registered.
- [ 1.319307] sensor_register_slave:mpu6880_gyro,id=49
- [ 1.320560] Registered cp15_barrier emulation handler
- [ 1.320683] mmc1: new HS400 Enhanced strobe MMC card at address 0001
- [ 1.320714] Registered setend emulation handler
- [ 1.321492] mmcblk1: mmc1:0001 AJTD4R 14.6 GiB
- [ 1.321547] registered taskstats version 1
- [ 1.321743] mmcblk1boot0: mmc1:0001 AJTD4R partition 1 4.00 MiB
- [ 1.322457] mmcblk1boot1: mmc1:0001 AJTD4R partition 2 4.00 MiB
- [ 1.322658] rockchip ion idev is NULL
- [ 1.322679] rga2 ff680000.rga: rga ion client create success!
- [ 1.322923] rga: Driver loaded successfully ver:3.02
- [ 1.323046] mmcblk1rpmb: mmc1:0001 AJTD4R partition 3 4.00 MiB
- [ 1.323611] uboot: 0x000400000 -- 0x000800000 (4 MB)
- [ 1.323627] trust: 0x000800000 -- 0x000c00000 (4 MB)
- [ 1.323639] misc: 0x000c00000 -- 0x001000000 (4 MB)
- [ 1.323651] resource: 0x001000000 -- 0x002000000 (16 MB)
- [ 1.323663] kernel: 0x002000000 -- 0x003800000 (24 MB)
- [ 1.323674] boot: 0x003800000 -- 0x005800000 (32 MB)
- [ 1.323686] recovery: 0x005800000 -- 0x007800000 (32 MB)
- [ 1.323699] backup: 0x007800000 -- 0x00e800000 (112 MB)
- [ 1.323713] cache: 0x00e800000 -- 0x016800000 (128 MB)
- [ 1.323727] system: 0x016800000 -- 0x076800000 (1536 MB)
- [ 1.323741] metadata: 0x076800000 -- 0x077800000 (16 MB)
- [ 1.323752] baseparamer: 0x077800000 -- 0x077c00000 (4 MB)
- [ 1.323764] userdata: 0x077c00000 -- 0x3a3a00000 (12990 MB)
- [ 1.323834] mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13
- [ 1.323921] rockchip-usb2phy ff770000.syscon:usb2-phy@e450: vbus_drv is not assigned
- [ 1.326359] rockchip-drm display-subsystem: bound ff900000.vop (ops vop_component_ops)
- [ 1.326594] rockchip-drm display-subsystem: bound ff8f0000.vop (ops vop_component_ops)
- [ 1.327109] i2c i2c-9: of_i2c: modalias failure on /hdmi@ff940000/ports
- [ 1.327146] dwhdmi-rockchip ff940000.hdmi: registered DesignWare HDMI I2C bus driver
- [ 1.327217] dwhdmi-rockchip ff940000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
- [ 1.328404] rockchip-drm display-subsystem: bound ff940000.hdmi (ops dw_hdmi_rockchip_ops)
- [ 1.328918] i2c i2c-10: of_i2c: modalias failure on /dp@fec00000/ports
- [ 1.329437] cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] Not connected. Disabling cdn
- [ 1.329485] rockchip-drm display-subsystem: bound fec00000.dp (ops cdn_dp_component_ops)
- [ 1.329503] [drm:drm_vblank_init] Supports vblank timestamp caching Rev 2 (21.10.2013).
- [ 1.329517] [drm:drm_vblank_init] No driver support for vblank timestamp query.
- [ 1.355193] usb 1-1: new high-speed USB device number 2 using ehci-platform
- [ 1.480189] usb 1-1: New USB device found, idVendor=1a40, idProduct=0201
- [ 1.480298] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
- [ 1.480325] usb 1-1: Product: USB 2.0 Hub [MTT]
- [ 1.481548] hub 1-1:1.0: USB hub found
- [ 1.481752] hub 1-1:1.0: 7 ports detected
- [ 1.761943] usb 1-1.2: new full-speed USB device number 3 using ehci-platform
- [ 1.842177] rockchip-drm display-subsystem: fb0: frame buffer device
- [ 1.847617] vendor storage:20160801 ret = 0
- [ 1.857731] mali ff9a0000.gpu: leakage=24
- [ 1.867608] usb 1-1.2: New USB device found, idVendor=0403, idProduct=6001
- [ 1.867701] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
- [ 1.867740] usb 1-1.2: Product: iClebo Kobuki
- [ 1.867764] usb 1-1.2: Manufacturer: Yujin Robot
- [ 1.867788] usb 1-1.2: SerialNumber: kobuki_AL03EQNE
- [ 1.871327] ftdi_sio 1-1.2:1.0: FTDI USB Serial Device converter detected
- [ 1.871588] usb 1-1.2: Detected FT232RL
- [ 1.872425] mali ff9a0000.gpu: temp=52222, pvtm=120534 (120402 + 132)
- [ 1.872482] usb 1-1.2: FTDI USB Serial Device converter now attached to ttyUSB0
- [ 1.875052] mali ff9a0000.gpu: pvtm-sel=0
- [ 1.876532] mali ff9a0000.gpu: GPU identified as 0x0860 r2p0 status 0
- [ 1.877577] I : [File] : drivers/gpu/arm/midgard/backend/gpu/mali_kbase_devfreq.c; [Line] : 284; [Func] : kbase_devfreq_init(); success initing power_model_simple.
- [ 1.878551] mali ff9a0000.gpu: Probed as mali0
- [ 1.884585] xhci-hcd xhci-hcd.10.auto: xHCI Host Controller
- [ 1.885249] xhci-hcd xhci-hcd.10.auto: new USB bus registered, assigned bus number 3
- [ 1.885652] xhci-hcd xhci-hcd.10.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x02030010
- [ 1.885764] xhci-hcd xhci-hcd.10.auto: irq 233, io mem 0xfe800000
- [ 1.886013] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
- [ 1.886045] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 1.886073] usb usb3: Product: xHCI Host Controller
- [ 1.886094] usb usb3: Manufacturer: Linux 4.4.103 xhci-hcd
- [ 1.886117] usb usb3: SerialNumber: xhci-hcd.10.auto
- [ 1.890584] hub 3-0:1.0: USB hub found
- [ 1.890666] hub 3-0:1.0: 1 port detected
- [ 1.891177] xhci-hcd xhci-hcd.10.auto: xHCI Host Controller
- [ 1.891217] xhci-hcd xhci-hcd.10.auto: new USB bus registered, assigned bus number 4
- [ 1.893171] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
- [ 1.893377] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
- [ 1.893408] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 1.893433] usb usb4: Product: xHCI Host Controller
- [ 1.893455] usb usb4: Manufacturer: Linux 4.4.103 xhci-hcd
- [ 1.893476] usb usb4: SerialNumber: xhci-hcd.10.auto
- [ 1.894284] hub 4-0:1.0: USB hub found
- [ 1.894354] hub 4-0:1.0: 1 port detected
- [ 1.900839] xhci-hcd xhci-hcd.10.auto: remove, state 1
- [ 1.900909] usb usb4: USB disconnect, device number 1
- [ 1.929807] xhci-hcd xhci-hcd.10.auto: Host not halted after 16000 microseconds.
- [ 1.929838] xhci-hcd xhci-hcd.10.auto: Host controller not halted, aborting reset.
- [ 1.932104] xhci-hcd xhci-hcd.10.auto: USB bus 4 deregistered
- [ 1.932640] xhci-hcd xhci-hcd.10.auto: remove, state 1
- [ 1.933120] usb usb3: USB disconnect, device number 1
- [ 1.933990] xhci-hcd xhci-hcd.10.auto: USB bus 3 deregistered
- [ 1.939658] xhci-hcd xhci-hcd.11.auto: xHCI Host Controller
- [ 1.939815] xhci-hcd xhci-hcd.11.auto: new USB bus registered, assigned bus number 3
- [ 1.940300] xhci-hcd xhci-hcd.11.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x02030010
- [ 1.940403] xhci-hcd xhci-hcd.11.auto: irq 234, io mem 0xfe900000
- [ 1.940733] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
- [ 1.940765] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 1.940793] usb usb3: Product: xHCI Host Controller
- [ 1.940818] usb usb3: Manufacturer: Linux 4.4.103 xhci-hcd
- [ 1.940842] usb usb3: SerialNumber: xhci-hcd.11.auto
- [ 1.945558] hub 3-0:1.0: USB hub found
- [ 1.945726] hub 3-0:1.0: 1 port detected
- [ 1.946348] xhci-hcd xhci-hcd.11.auto: xHCI Host Controller
- [ 1.946392] xhci-hcd xhci-hcd.11.auto: new USB bus registered, assigned bus number 4
- [ 1.946637] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
- [ 1.946878] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
- [ 1.946910] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 1.946936] usb usb4: Product: xHCI Host Controller
- [ 1.946961] usb usb4: Manufacturer: Linux 4.4.103 xhci-hcd
- [ 1.946986] usb usb4: SerialNumber: xhci-hcd.11.auto
- [ 1.948581] hub 4-0:1.0: USB hub found
- [ 1.948683] hub 4-0:1.0: 1 port detected
- [ 1.951858] usb 1-1.4: new full-speed USB device number 4 using ehci-platform
- [ 1.954202] ehci-platform fe380000.usb: EHCI Host Controller
- [ 1.954283] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 5
- [ 1.954664] ehci-platform fe380000.usb: irq 28, io mem 0xfe380000
- [ 2.042130] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
- [ 2.042536] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
- [ 2.042568] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 2.042595] usb usb5: Product: EHCI Host Controller
- [ 2.042620] usb usb5: Manufacturer: Linux 4.4.103 ehci_hcd
- [ 2.042644] usb usb5: SerialNumber: fe380000.usb
- [ 2.045801] hub 5-0:1.0: USB hub found
- [ 2.045877] hub 5-0:1.0: 1 port detected
- [ 2.047622] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
- [ 2.047683] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 6
- [ 2.048033] ohci-platform fe3a0000.usb: irq 29, io mem 0xfe3a0000
- [ 2.054113] usb 1-1.4: New USB device found, idVendor=222a, idProduct=0001
- [ 2.054219] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
- [ 2.054248] usb 1-1.4: Product: ILITEK-TP
- [ 2.054271] usb 1-1.4: Manufacturer: ILITEK
- [ 2.054293] usb 1-1.4: SerialNumber: V06.00.00.00
- [ 2.066377] input: ILITEK ILITEK-TP as /devices/platform/fe3c0000.usb/usb1/1-1/1-1.4/1-1.4:1.0/0003:222A:0001.0001/input/input1
- [ 2.103181] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
- [ 2.103248] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 2.103276] usb usb6: Product: Generic Platform OHCI controller
- [ 2.103302] usb usb6: Manufacturer: Linux 4.4.103 ohci_hcd
- [ 2.103326] usb usb6: SerialNumber: fe3a0000.usb
- [ 2.105787] hub 6-0:1.0: USB hub found
- [ 2.105864] hub 6-0:1.0: 1 port detected
- [ 2.108651] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
- [ 2.109112] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
- [ 2.109149] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
- [ 2.109212] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo
- [ 2.109280] dwmmc_rockchip fe310000.dwmmc: 'clock-freq-min-max' property was deprecated.
- [ 2.109373] dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found
- [ 2.109397] dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found
- [ 2.110074] dwmmc_rockchip fe310000.dwmmc: allocated mmc-pwrseq
- [ 2.119497] hid-multitouch 0003:222A:0001.0001: input,hidraw0: USB HID v1.10 Device [ILITEK ILITEK-TP] on usb-fe3c0000.usb-1.4/input0
- [ 2.121997] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
- [ 2.123955] input: ILITEK ILITEK-TP as /devices/platform/fe3c0000.usb/usb1/1-1/1-1.4/1-1.4:1.1/0003:222A:0001.0002/input/input2
- [ 2.135218] dwmmc_rockchip fe310000.dwmmc: 1 slots initialized
- [ 2.149314] asoc-simple-card rt5640-sound: rt5640-aif1 <-> ff890000.i2s mapping ok
- [ 2.154921] input: rockchip,rt5640-codec Headphone Jack as /devices/platform/rt5640-sound/sound/card0/input3
- [ 2.176193] hid-generic 0003:222A:0001.0002: input,hiddev0,hidraw1: USB HID v1.10 Mouse [ILITEK ILITEK-TP] on usb-fe3c0000.usb-1.4/input1
- [ 2.180313] asoc-simple-card spdif-sound: dit-hifi <-> ff870000.spdif mapping ok
- [ 2.182230] mmc2: queuing unknown CIS tuple 0x80 (2 bytes)
- [ 2.183892] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
- [ 2.184959] rk-hdmi-dp-sound hdmi-dp-sound: control 3:0:0:ELD:0 is already present
- [ 2.185547] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
- [ 2.185690] hdmi-audio-codec hdmi-audio-codec.9.auto: ASoC: Failed to add ELD: -16
- [ 2.188133] rk-hdmi-dp-sound hdmi-dp-sound: multicodec <-> ff8a0000.i2s mapping ok
- [ 2.188515] mmc2: queuing unknown CIS tuple 0x80 (7 bytes)
- [ 2.188974] hdmi-audio-codec hdmi-audio-codec.9.auto: ASoC: Failed to create Playback debugfs file
- [ 2.192122] otg_wakelock_init: No USB transceiver found
- [ 2.193768] rk808-rtc rk808-rtc: setting system clock to 2013-01-18 08:57:18 UTC (1358499438)
- [ 2.195171] It doesn't contain Rogue gpu
- [ 2.221331] ret 1024
- [ 2.222274] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 414; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko .
- [ 2.223366] Mali: Mali device driver loaded
- [ 2.224626] input: rk29-keypad as /devices/platform/rockchip-key/input/input4
- [ 2.226822] ALSA device list:
- [ 2.226892] #0: rockchip,rt5640-codec
- [ 2.226913] #1: ROCKCHIP,SPDIF
- [ 2.226932] #2: rk-hdmi-dp-sound
- [ 2.227902] Freeing unused kernel memory: 832K
- [ 2.233534] init: init first stage started!
- [ 2.237001] init: init second stage started!
- [ 2.243563] init: Setting ro.rk.soc=rk3399
- [ 2.243704] init: OK,EMMC DRIVERS INIT OK
- [ 2.243738] init: property_set("ro.boot.mode", "emmc") failed
- [ 2.243836] init: property_set("ro.hardware", "rk30board") failed
- [ 2.243897] init: Running restorecon...
- [ 2.244067] init: waitpid failed: No child processes
- [ 2.244494] init: (Loading properties from /default.prop took 0.00s.)
- [ 2.246668] init: /init.rc: 588: invalid keyword 'echo'
- [ 2.247259] init: (Parsing /init.environ.rc took 0.00s.)
- [ 2.247544] mmc_host mmc2: Bus speed (slot 0) = 200000000Hz (slot req 208000000Hz, actual 200000000HZ div = 0)
- [ 2.248242] init: (Parsing /init.usb.rc took 0.00s.)
- [ 2.250645] init: (Parsing init.rk30board.bootmode.emmc.rc took 0.00s.)
- [ 2.251822] init: (Parsing init.rk30board.usb.rc took 0.00s.)
- [ 2.251919] init: (Parsing init.rk30board.environment.rc took 0.00s.)
- [ 2.252025] init: could not import file '/init.stt_trace.rc' from '/init.debug.rc': No such file or directory
- [ 2.252068] init: could not import file '/init.logs.rc' from '/init.debug.rc': No such file or directory
- [ 2.252110] init: could not import file '/init.crashlogd.rc' from '/init.debug.rc': No such file or directory
- [ 2.252152] init: could not import file '/init.coredump.rc' from '/init.debug.rc': No such file or directory
- [ 2.252206] init: could not import file '/init.log-watch.rc' from '/init.debug.rc': No such file or directory
- [ 2.252287] init: (Parsing /init.kernel.rc took 0.00s.)
- [ 2.252425] init: (Parsing /init.debug-charging.rc took 0.00s.)
- [ 2.252476] init: (Parsing /init.debug.rc took 0.00s.)
- [ 2.252505] init: (Parsing init.rockchip.rc took 0.00s.)
- [ 2.253111] init: (Parsing init.connectivity.rc took 0.00s.)
- [ 2.253237] init: (Parsing init.box.samba.rc took 0.00s.)
- [ 2.253408] init: (Parsing init.rk3399.rc took 0.00s.)
- [ 2.253570] init: init.box.rc: 25: invalid keyword 'ioprio'
- [ 2.253604] init: (Parsing init.box.rc took 0.00s.)
- [ 2.253653] init: could not import file 'init.car.rc' from '/init.rk30board.rc': No such file or directory
- [ 2.253695] init: could not import file 'init.optee.rc' from '/init.rk30board.rc': No such file or directory
- [ 2.253720] init: (Parsing /init.rk30board.rc took 0.01s.)
- [ 2.254733] init: (Parsing /init.usb.configfs.rc took 0.00s.)
- [ 2.254876] init: (Parsing /init.zygote64_32.rc took 0.00s.)
- [ 2.254901] init: (Parsing /init.rc took 0.01s.)
- [ 2.255413] init: Starting service 'ueventd'...
- [ 2.256976] init: write_file: Unable to open '/proc/sys/kernel/panic_on_stackoverflow': No such file or directory
- [ 2.260623] ueventd: ueventd started!
- [ 2.262196] ueventd: invalid gid 'trace'
- [ 2.369867] init: Waiting for /dev/.coldboot_done...
- [ 2.421236] ueventd: Coldboot took 0.16s.
- [ 2.430918] init: Waiting for /dev/.coldboot_done took 0.06s.
- [ 2.431071] init: /dev/hw_random not found
- [ 2.431719] keychord: using input dev ff420030.pwm for fevent
- [ 2.431775] keychord: using input dev rk29-keypad for fevent
- [ 2.434560] init: write_file: Unable to open '/proc/cpu/alignment': No such file or directory
- [ 2.441470] Registered swp emulation handler
- [ 2.441686] init: write_file: Unable to open '/sys/module/rockchip_pm/parameters/policy': No such file or directory
- [ 2.442599] init: /dev/hw_random not found
- [ 2.442822] init: write_file: Unable to open '/sys/block/mmcblk0/bdi/read_ahead_kb': No such file or directory
- [ 2.443545] fs_mgr: Warning: unknown flag resize
- [ 2.446818] EXT4-fs (mmcblk1p10): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
- [ 2.446873] fs_mgr: __mount(source=/dev/block/platform/fe330000.sdhci/by-name/system,target=/system,type=ext4)=0
- [ 2.447601] fs_mgr: check_fs(): mount(/dev/block/platform/fe330000.sdhci/by-name/cache,/cache,ext4)=-1: No such file or directory
- [ 2.448169] fs_mgr: Running /system/bin/e2fsck on /dev/block/platform/fe330000.sdhci/by-name/cache
- [ 2.455307] random: e2fsck: uninitialized urandom read (40 bytes read, 52 bits of entropy available)
- [ 2.486348] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
- [ 2.486348]
- [ 2.486385] e2fsck: /dev/block/platform/fe330000.sdhci/by-name/cache: recovering journal
- [ 2.486385]
- [ 2.486398] e2fsck: /dev/block/platform/fe330000.sdhci/by-name/cache: clean, 39/8192 files, 1741/32768 blocks
- [ 2.486398]
- [ 2.490315] EXT4-fs (mmcblk1p9): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard
- [ 2.490363] fs_mgr: __mount(source=/dev/block/platform/fe330000.sdhci/by-name/cache,target=/cache,type=ext4)=0
- [ 2.491309] EXT4-fs (mmcblk1p11): Ignoring removed nomblk_io_submit option
- [ 2.492433] EXT4-fs (mmcblk1p11): recovery complete
- [ 2.492444] EXT4-fs (mmcblk1p11): mounted filesystem with ordered data mode. Opts: errors=remount-ro,nomblk_io_submit
- [ 2.492470] fs_mgr: check_fs(): mount(/dev/block/platform/fe330000.sdhci/by-name/metadata,/metadata,ext4)=0: Success
- [ 2.513818] fs_mgr: check_fs(): unmount(/metadata) succeeded
- [ 2.513871] fs_mgr: Running /system/bin/e2fsck on /dev/block/platform/fe330000.sdhci/by-name/metadata
- [ 2.514780] random: e2fsck: uninitialized urandom read (40 bytes read, 55 bits of entropy available)
- [ 2.525959] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
- [ 2.525959]
- [ 2.526029] e2fsck: /dev/block/platform/fe330000.sdhci/by-name/metadata has been mounted 10 times without being checked, check forced.
- [ 2.526029]
- [ 2.526046] e2fsck: Pass 1: Checking inodes, blocks, and sizes
- [ 2.526046]
- [ 2.526059] e2fsck: Pass 2: Checking directory structure
- [ 2.526059]
- [ 2.526071] e2fsck: Pass 3: Checking directory connectivity
- [ 2.526071]
- [ 2.526083] e2fsck: Pass 4: Checking reference counts
- [ 2.526083]
- [ 2.526095] e2fsck: Pass 5: Checking group summary information
- [ 2.526095]
- [ 2.526109] e2fsck: /dev/block/platform/fe330000.sdhci/by-name/metadata: 11/1024 files (0.0% non-contiguous), 1102/4096 blocks
- [ 2.526109]
- [ 2.528203] EXT4-fs (mmcblk1p11): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard
- [ 2.528252] fs_mgr: __mount(source=/dev/block/platform/fe330000.sdhci/by-name/metadata,target=/metadata,type=ext4)=0
- [ 2.528304] fs_mgr: Running /system/bin/fsck.f2fs -a /dev/block/platform/fe330000.sdhci/by-name/userdata
- [ 2.529479] fsck.f2fs: executing /system/bin/fsck.f2fs failed: No such file or directory
- [ 2.529479]
- [ 2.529520] fsck.f2fs: fsck.f2fs terminated by exit(255)
- [ 2.529520]
- [ 2.545662] dwmmc_rockchip fe310000.dwmmc: Successfully tuned phase to 247
- [ 2.548008] mmc2: queuing unknown CIS tuple 0x91 (3 bytes)
- [ 2.548042] mmc2: new ultra high speed SDR104 SDIO card at address 0001
- [ 12.437465] random: nonblocking pool is initialized
复制代码 等了约莫十几分钟3399还是没有起来, 镜像是自己编译烧录的, 长时间断电后就会出现这种情况,有人可以解释一下为什么会出现这种情况么。
|
|