Firefly开源社区

打印 上一主题 下一主题

[Linux] [求助]AIO-3288J HDMI_IN HDMI采集没试通

25

积分

0

威望

0

贡献

技术小白

积分
25

[求助]AIO-3288J HDMI_IN HDMI采集没试通

发表于 2020-11-4 18:28:30      浏览:4768 | 回复:7        打印      只看该作者   [复制链接] 楼主
[ 本帖最后由 warrior.li 于 2020-11-4 18:31 编辑 ]\n\n今天刚拿到 AIO-3288J的开发板,想试试HDMI采集功能。目前拿到板子后做了如下操作:
1.升级固件到ubuntu 18.04 hdmi_in
根据说明升级固件,原来是安卓,似乎需要先清flash再烧写
烧写的固件为:AIO-3288J-HDMIIN-UBUNTU18.04-GPT-20200403-1455.img

2.搭建环境
A.115200 连debug串口 使用 mobaXterm
B.网络连接路由器,可DHCP获取1段IP
C.HDMI OUT连接一台1080P显示器,开机可正确看到ubuntu桌面
D.使用 apt-get update   apt-get install vlc  安装了 VLC
E.准备一台 x86主机(ubuntu 20.04),该主机有 VGA和 HDMI 两个接口
  VGA连显示器, HDMI准备后续连 AIO-3288J 的 HDMI_IN 接口

3.实验过程
A.aio-3288j HDMI连显示器,连USB 键盘鼠标 开机,进入桌面,打开terminal
  此时未连接 HDMI IN
  sudo su
  dmesg >dmesg-1.txt
   
B.x86主机开机,从VGA+USB键盘打开 terminal 用 xrandr 可以看到当前输出为
  VGA-1  conected  1440x900
  也就是目前的分辨率
   
C.连接x86主机的 hdmi 输出到 aio-3288j 的 hdmi_in 端口
  x86主机自动识别了hdmi输出,用 xrandr 命令可看到增加了
  HDMI-1 connect
  1920x1080 60*
  
D.此时在 aio-3288j 上执行
  dmesg >dmesg-2.txt
  可以看到增加了2行

[   38.430750] m00_b_tc35874x 1-000f: tc35874x_format_change: New format: 1920x1080p60.0 (2200x1125)
[   38.516879] m00_b_tc35874x 1-000f: tc35874x_format_change: New format: 1920x1080p60.0 (2200x1125)

  我认为应该识别了1080p的输入

E.回到 aio-3288j 的 ternmal 先 exit回到普通用户 firefly,因为 vlc用root执行不了
  执行
  vlc |tee vlc_log.txt
  
  之后在图形界面选择 open capture device
  尝试了从 /dev/video0   到  /dev/video4
  哪个都打不开

F.尝试后续拔掉 HDMI IN  查看 dmesg 无新增打印  


我想知道如何才能把hdmi 采集调通,是不是我用的方法不对?


log文件好像不能上传?我就直接贴进来了dmesg-1.txt[    0.000000] Booting Linux on physical CPU 0x500
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.194 (llq@llq-H310M-DS2V) (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05) ) #250 SMP Fri Apr 3 14:46:41 CST 2020
[    0.000000] CPU: ARMv7 Processor [410fc0d1] revision 1 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: AIO-3288J Board (Linux Opensource)
[    0.000000] cma: Reserved 16 MiB at 0x7f000000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 520704
[    0.000000] free_area_init_node: node 0, pgdat c13f17c0, node_mem_map eeffa000
[    0.000000]   Normal zone: 1536 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 193024 pages, LIFO batch:31
[    0.000000]   HighMem zone: 327680 pages, LIFO batch:31
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv65535.65535 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] PERCPU: Embedded 14 pages/cpu @eef77000 s24728 r8192 d24424 u57344
[    0.000000] pcpu-alloc: s24728 r8192 d24424 u57344 alloc=14*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 519168
[    0.000000] Kernel command line: storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal  androidboot.slot_suffix=  earlyprintk rw rootwait console=ttyFIQ0 root=PARTUUID=614e0000-0000 rootfstype=ext4 systemd.gpt_auto=0
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 2027056K/2082816K available (12288K kernel code, 1003K rwdata, 3464K rodata, 1024K init, 632K bss, 39376K reserved, 16384K cma-reserved, 1293716K highmem)
[    0.000000] Virtual kernel memory layout:
                   vector  : 0xffff0000 - 0xffff1000   (   4 kB)
                   fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
                   vmalloc : 0xf0800000 - 0xff800000   ( 240 MB)
                   lowmem  : 0xc0000000 - 0xf0000000   ( 768 MB)
                   pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
                   modules : 0xbf000000 - 0xbfe00000   (  14 MB)
                     .text : 0xc0008000 - 0xc0d00000   (13280 kB)
                     .init : 0xc1200000 - 0xc1300000   (1024 kB)
                     .data : 0xc1300000 - 0xc13faf2c   (1004 kB)
                      .bss : 0xc13fc000 - 0xc149a210   ( 633 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]         Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000009] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000030] Switching to timer-based delay loop, resolution 41ns
[    0.004012] Console: colour dummy device 80x30
[    0.004055] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.004080] pid_max: default: 32768 minimum: 301
[    0.004209] Security Framework initialized
[    0.004227] Yama: becoming mindful.
[    0.004321] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.004345] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.005494] Initializing cgroup subsys devices
[    0.005527] Initializing cgroup subsys freezer
[    0.005575] CPU: Testing write buffer coherency: ok
[    0.005630] ftrace: allocating 44299 entries in 130 pages
[    0.131512] CPU0: update cpu_capacity 430
[    0.131532] CPU0: thread -1, cpu 0, socket 5, mpidr 80000500
[    0.131631] Setting up static identity map for 0x100000 - 0x100058
[    0.134941] CPU1: update cpu_capacity 430
[    0.134950] CPU1: thread -1, cpu 1, socket 5, mpidr 80000501
[    0.136165] CPU2: update cpu_capacity 430
[    0.136175] CPU2: thread -1, cpu 2, socket 5, mpidr 80000502
[    0.137373] CPU3: update cpu_capacity 430
[    0.137382] CPU3: thread -1, cpu 3, socket 5, mpidr 80000503
[    0.137544] Brought up 4 CPUs
[    0.137587] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[    0.137597] CPU: All CPU(s) started in SVC mode.
[    0.139639] devtmpfs: initialized
[    0.171648] VFP support v0.3: implementor 41 architecture 3 part 30 variant d rev 0
[    0.172212] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.172257] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.173730] pinctrl core: initialized pinctrl subsystem
[    0.175368] NET: Registered protocol family 16
[    0.177940] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.201351] cpuidle: using governor ladder
[    0.231398] cpuidle: using governor menu
[    0.231453] Registered FIQ tty driver
[    0.265942] gpiochip_add_data: registered GPIOs 0 to 23 on device: gpio0
[    0.266125] gpiochip_add_data: registered GPIOs 24 to 55 on device: gpio1
[    0.266289] gpiochip_add_data: registered GPIOs 56 to 87 on device: gpio2
[    0.266461] gpiochip_add_data: registered GPIOs 88 to 119 on device: gpio3
[    0.266621] gpiochip_add_data: registered GPIOs 120 to 151 on device: gpio4
[    0.266776] gpiochip_add_data: registered GPIOs 152 to 183 on device: gpio5
[    0.266959] gpiochip_add_data: registered GPIOs 184 to 215 on device: gpio6
[    0.267121] gpiochip_add_data: registered GPIOs 216 to 247 on device: gpio7
[    0.267281] gpiochip_add_data: registered GPIOs 248 to 263 on device: gpio8
[    0.286140] console [pstore-1] enabled
[    0.286154] pstore: Registered ramoops as persistent store backend
[    0.286170] ramoops: attached 0xf0000@0x8000000, ecc: 0/0
[    0.287552] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.287572] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.288699] fiq debugger fiq mode enabled
[    0.759797] console [ttyFIQ0] enabled
[    0.763839] Registered fiq debugger ttyFIQ0
[    0.851657] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vccadc-ref[0]'
[    0.852366] of_get_named_gpiod_flags: parsed 'gpio' property of node '/usb-host-regulator[0]' - status (0)
[    0.853109] of_get_named_gpiod_flags: parsed 'gpio' property of node '/usb-otg-regulator[0]' - status (0)
[    0.853645] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vsys-regulator[0]'
[    0.854153] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/flash-regulator[0]'
[    0.854488] vcc_flash: regulator get failed, ret=-517
[    0.859926] of_get_named_gpiod_flags: parsed 'gpio' property of node '/sdmmc-regulator[0]' - status (0)
[    0.860346] vcc_sd: regulator get failed, ret=-517
[    0.865454] of_get_named_gpiod_flags: parsed 'gpio' property of node '/vcc28-dvp-regulator[0]' - status (0)
[    0.865860] vcc28_dvp: regulator get failed, ret=-517
[    0.871124] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/dovdd-1v8-regulator[0]'
[    0.871662] dovdd_1v8: regulator get failed, ret=-517
[    0.877177] of_get_named_gpiod_flags: parsed 'gpio' property of node '/vcc-sys-5v[0]' - status (0)
[    0.878653] iommu: Adding device ff910000.rkisp1 to group 0
[    0.884440] iommu: Adding device ff930000.vop to group 1
[    0.889911] iommu: Adding device ff940000.vop to group 2
[    0.895430] iommu: Adding device ff9a0000.vpu-service to group 3
[    0.901604] iommu: Adding device ff9c0000.hevc-service to group 4
[    0.908599] rk_iommu ff914000.iommu: can't get sclk
[    0.914163] rk_iommu ff930300.iommu: can't get sclk
[    0.919543] rk_iommu ff940300.iommu: can't get sclk
[    0.924865] rk_iommu ff9a0800.iommu: can't get sclk
[    0.930337] rk_iommu ff9c0440.iommu: can't get sclk
[    0.936095] SCSI subsystem initialized
[    0.940300] usbcore: registered new interface driver usbfs
[    0.945895] usbcore: registered new interface driver hub
[    0.951419] usbcore: registered new device driver usb
[    0.956700] media: Linux media interface: v0.10
[    0.961356] Linux video capture interface: v2.00
[    0.966138] pps_core: LinuxPPS API ver. 1 registered
[    0.971107] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.980309] PTP clock support registered
[    0.986680] Advanced Linux Sound Architecture Driver Initialized.
[    0.993862] Bluetooth: Core ver 2.21
[    0.997504] NET: Registered protocol family 31
[    1.001954] Bluetooth: HCI device and connection manager initialized
[    1.008366] Bluetooth: HCI socket layer initialized
[    1.013257] Bluetooth: L2CAP socket layer initialized
[    1.018399] Bluetooth: SCO socket layer initialized
[    1.024936] rockchip-cpuinfo cpuinfo: Serial                : ee0cb30bbb322108
[    1.032431] clocksource: Switched to clocksource arch_sys_counter
[    1.123462] NET: Registered protocol family 2
[    1.128749] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    1.135973] TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
[    1.142794] TCP: Hash tables configured (established 8192 bind 8192)
[    1.149244] UDP hash table entries: 512 (order: 2, 24576 bytes)
[    1.155272] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes)
[    1.161971] NET: Registered protocol family 1
[    1.166892] RPC: Registered named UNIX socket transport module.
[    1.172871] RPC: Registered udp transport module.
[    1.177585] RPC: Registered tcp transport module.
[    1.182295] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.190466] hw perfevents: enabled with armv7_cortex_a12 PMU driver, 7 counters available
[    1.202254] Initialise system trusted keyring
[    1.222534] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.231651] NFS: Registering the id_resolver key type
[    1.236811] Key type id_resolver registered
[    1.241009] Key type id_legacy registered
[    1.245097] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.252891] fuse init (API version 7.23)
[    1.265682] NET: Registered protocol family 38
[    1.270163] Key type asymmetric registered
[    1.274389] Asymmetric key parser 'x509' registered
[    1.279399] bounce: pool size: 64 pages
[    1.283654] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[    1.291069] io scheduler noop registered
[    1.295110] io scheduler deadline registered
[    1.299453] io scheduler cfq registered (default)
[    1.313164] rk-vcodec ff9a0000.vpu-service: no regulator for vcodec
[    1.319862] rk-vcodec ff9a0000.vpu-service: probe device
[    1.325724] rk-vcodec ff9a0000.vpu-service: drm allocator with mmu enabled
[    1.333901] rk-vcodec ff9a0000.vpu-service: could not find power_model node
[    1.340875] rk-vcodec ff9a0000.vpu-service: init success
[    1.346788] rk-vcodec ff9c0000.hevc-service: no regulator for vcodec
[    1.353706] rk-vcodec ff9c0000.hevc-service: probe device
[    1.359535] rk-vcodec ff9c0000.hevc-service: drm allocator with mmu enabled
[    1.367414] rk-vcodec ff9c0000.hevc-service: could not find power_model node
[    1.374529] rk-vcodec ff9c0000.hevc-service: init success
[    1.383674] dma-pl330 ff250000.dma-controller: Loaded driver for PL330 DMAC-241330
[    1.391265] dma-pl330 ff250000.dma-controller:         DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[    1.401923] dma-pl330 ff600000.dma-controller: Loaded driver for PL330 DMAC-241330
[    1.409561] dma-pl330 ff600000.dma-controller:         DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10
[    1.420668] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[    1.429427] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled
[    1.436951] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 38, base_baud = 1500000) is a 16550A
[    1.446920] ff190000.serial: ttyS1 at MMIO 0xff190000 (irq = 39, base_baud = 1500000) is a 16550A
[    1.456859] ff1b0000.serial: ttyS3 at MMIO 0xff1b0000 (irq = 40, base_baud = 1500000) is a 16550A
[    1.468214] [drm] Initialized drm 1.1.0 20060810
[    1.479991] [drm] Rockchip DRM driver version: v1.0.1
[    1.485672] rockchip-drm display-subsystem: devfreq is not set
[    1.493124] rockchip-drm display-subsystem: bound ff930000.vop (ops 0xc0d664f8)
[    1.501592] rockchip-drm display-subsystem: bound ff940000.vop (ops 0xc0d664f8)
[    1.509373] i2c i2c-6: of_i2c: modalias failure on /hdmi@ff980000/ports
[    1.516064] dwhdmi-rockchip ff980000.hdmi: registered DesignWare HDMI I2C bus driver
[    1.523991] dwhdmi-rockchip ff980000.hdmi: Detected HDMI TX controller v2.01a with HDCP (DWC HDMI 2.0 TX PHY)
[    1.535534] rockchip-drm display-subsystem: bound ff980000.hdmi (ops 0xc0d5d420)
[    1.543010] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    1.549626] [drm] No driver support for vblank timestamp query.
[    1.823495] rockchip-drm display-subsystem: fb0:  frame buffer device
[    1.855216] usbcore: registered new interface driver udl
[    1.866377] mali ffa30000.gpu: Failed to get regulator
[    1.871535] mali ffa30000.gpu: Power control initialization failed
[    1.879762] brd: module loaded
[    1.893669] loop: module loaded
[    1.898030] zram: Added device: zram0
[    1.901749] lkdtm: No crash points registered, enable through debugfs
[    1.909564] rockchip-spi ff110000.spi: no high_speed pinctrl state
[    1.917713] 11wk2xxx_probe: setup mode 0, 8 bits/w, 10000000 Hz max
[    1.924186] of_get_named_gpiod_flags: parsed 'power-gpio' property of node '/spi@ff110000/spi-wk2xxx@00[0]' - status (0)
[    1.924295] of_get_named_gpiod_flags: parsed 'reset-gpio' property of node '/spi@ff110000/spi-wk2xxx@00[0]' - status (0)
[    2.094441] of_get_named_gpiod_flags: parsed 'irq-gpio' property of node '/spi@ff110000/spi-wk2xxx@00[0]' - status (0)
[    2.094547] of_get_named_gpiod_flags: parsed 'cs-gpio' property of node '/spi@ff110000/spi-wk2xxx@00[0]' - status (0)
[    2.094815] wk2xxx_serial_init()
[    2.098056] wk2xxx_request_port
[    2.101212] ttysWK0 at I/O 0x1 (irq = 82, base_baud = 460800) is a wk2xxx
[    2.108479] uart_add_one_port success for line i:= 0 with right 0
[    2.114637] wk2xxx_request_port
[    2.117797] ttysWK1 at I/O 0x2 (irq = 82, base_baud = 460800) is a wk2xxx
[    2.125047] uart_add_one_port success for line i:= 1 with right 0
[    2.131147] wk2xxx_request_port
[    2.134350] ttysWK2 at I/O 0x3 (irq = 82, base_baud = 460800) is a wk2xxx
[    2.141571] uart_add_one_port success for line i:= 2 with right 0
[    2.147718] wk2xxx_request_port
[    2.150875] ttysWK3 at I/O 0x4 (irq = 82, base_baud = 460800) is a wk2xxx
[    2.158121] uart_add_one_port success for line i:= 3 with right 0
[    2.164265] uart_add_one_port = 0x0
[    2.167815] register spi return v = :0
[    2.171676] tun: Universal TUN/TAP device driver, 1.6
[    2.176775] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    2.185512] force_sf_dma_mode is ignored if force_thresh_dma_mode is set.
[    2.192171] rk_gmac-dwmac ff290000.ethernet: phy regulator is not available yet, deferred probing
[    2.202888] PPP generic driver version 2.4.2
[    2.207654] usbcore: registered new interface driver rndis_wlan
[    2.214017] usbcore: registered new interface driver rt2800usb
[    2.219978] Rockchip WiFi SYS interface (V1.00) ...
[    2.225073] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[    2.232615] usbcore: registered new interface driver pegasus
[    2.238382] usbcore: registered new interface driver rtl8150
[    2.244185] usbcore: registered new interface driver r8152
[    2.249780] usbcore: registered new interface driver asix
[    2.255316] usbcore: registered new interface driver ax88179_178a
[    2.261499] usbcore: registered new interface driver cdc_ether
[    2.267474] usbcore: registered new interface driver dm9601
[    2.273201] usbcore: registered new interface driver smsc75xx
[    2.279066] usbcore: registered new interface driver smsc95xx
[    2.284954] usbcore: registered new interface driver net1080
[    2.290707] usbcore: registered new interface driver rndis_host
[    2.296771] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[    2.304340] usbcore: registered new interface driver cdc_ncm
[    2.310095] usbcore: registered new interface driver qmi_wwan
[    2.315979] usbcore: registered new interface driver cdc_mbim
[    2.322347] ff540000.usb supply vusb_d not found, using dummy regulator
[    2.329133] ff540000.usb supply vusb_a not found, using dummy regulator
[    2.453151] dwc2 ff540000.usb: DWC OTG Controller
[    2.457904] dwc2 ff540000.usb: new USB bus registered, assigned bus number 1
[    2.465058] dwc2 ff540000.usb: irq 46, io mem 0xff540000
[    2.470783] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.477631] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.484892] usb usb1: Product: DWC OTG Controller
[    2.489608] usb usb1: Manufacturer: Linux 4.4.194 dwc2_hsotg
[    2.495299] usb usb1: SerialNumber: ff540000.usb
[    2.500974] hub 1-0:1.0: USB hub found
[    2.504850] hub 1-0:1.0: 1 port detected
[    2.509751] ff580000.usb supply vusb_d not found, using dummy regulator
[    2.516582] ff580000.usb supply vusb_a not found, using dummy regulator
[    2.534090] dwc2 ff580000.usb: DWC OTG Controller
[    2.538845] dwc2 ff580000.usb: new USB bus registered, assigned bus number 2
[    2.546003] dwc2 ff580000.usb: irq 47, io mem 0xff580000
[    2.551686] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    2.558526] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.565790] usb usb2: Product: DWC OTG Controller
[    2.570506] usb usb2: Manufacturer: Linux 4.4.194 dwc2_hsotg
[    2.576196] usb usb2: SerialNumber: ff580000.usb
[    2.581897] hub 2-0:1.0: USB hub found
[    2.585770] hub 2-0:1.0: 1 port detected
[    2.592048] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.598651] ehci-platform: EHCI generic platform driver
[    2.604537] ehci-platform ff500000.usb: EHCI Host Controller
[    2.610588] ehci-platform ff500000.usb: new USB bus registered, assigned bus number 3
[    2.618719] ehci-platform ff500000.usb: irq 44, io mem 0xff500000
[    2.642493] ehci-platform ff500000.usb: USB 2.0 started, EHCI 1.00
[    2.649028] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    2.655875] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.663141] usb usb3: Product: EHCI Host Controller
[    2.668028] usb usb3: Manufacturer: Linux 4.4.194 ehci_hcd
[    2.673550] usb usb3: SerialNumber: ff500000.usb
[    2.679149] hub 3-0:1.0: USB hub found
[    2.683224] hub 3-0:1.0: 1 port detected
[    2.688237] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.694536] ohci-platform: OHCI generic platform driver
[    2.700169] ohci-platform ff520000.usb: Generic Platform OHCI controller
[    2.707465] ohci-platform ff520000.usb: new USB bus registered, assigned bus number 4
[    2.715568] ohci-platform ff520000.usb: irq 45, io mem 0xff520000
[    2.776795] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    2.783664] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.790897] usb usb4: Product: Generic Platform OHCI controller
[    2.796866] usb usb4: Manufacturer: Linux 4.4.194 ohci_hcd
[    2.802363] usb usb4: SerialNumber: ff520000.usb
[    2.808801] hub 4-0:1.0: USB hub found
[    2.812690] hub 4-0:1.0: 1 port detected
[    2.817742] usbcore: registered new interface driver cdc_acm
[    2.823475] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    2.831735] usbcore: registered new interface driver cdc_wdm
[    2.837663] usbcore: registered new interface driver usb-storage
[    2.843900] usbcore: registered new interface driver usbserial
[    2.849822] usbcore: registered new interface driver usbserial_generic
[    2.856452] usbserial: USB Serial support registered for generic
[    2.862608] usbcore: registered new interface driver ch341
[    2.868159] usbserial: USB Serial support registered for ch341-uart
[    2.874581] usbcore: registered new interface driver cp210x
[    2.880214] usbserial: USB Serial support registered for cp210x
[    2.886284] usb 1-1: new high-speed USB device number 2 using dwc2
[    2.892711] usbcore: registered new interface driver ftdi_sio
[    2.898536] usbserial: USB Serial support registered for FTDI USB Serial Device
[    2.906201] usbcore: registered new interface driver keyspan
[    2.911922] usbserial: USB Serial support registered for Keyspan - (without firmware)
[    2.919871] usbserial: USB Serial support registered for Keyspan 1 port adapter
[    2.927277] usbserial: USB Serial support registered for Keyspan 2 port adapter
[    2.934682] usbserial: USB Serial support registered for Keyspan 4 port adapter
[    2.942131] usbcore: registered new interface driver option
[    2.947824] usbserial: USB Serial support registered for GSM modem (1-port)
[    2.955219] usbcore: registered new interface driver oti6858
[    2.960939] usbserial: USB Serial support registered for oti6858
[    2.967098] usbcore: registered new interface driver pl2303
[    2.972798] usbserial: USB Serial support registered for pl2303
[    2.978846] usbcore: registered new interface driver qcserial
[    2.984693] usbserial: USB Serial support registered for Qualcomm USB modem
[    2.991815] usbcore: registered new interface driver sierra
[    2.997495] usbserial: USB Serial support registered for Sierra USB modem
[    3.006431] usbcore: registered new interface driver iforce
[    3.012153] usbcore: registered new interface driver xpad
[    3.017784] ==gsl_ts_init==
[    3.020667] ret=0
[    3.023148] usbcore: registered new interface driver usbtouchscreen
[    3.029803] .. rk pwm remotectl v1.1 init
[    3.034366] input: ff680000.pwm as /devices/platform/ff680000.pwm/input/input0
[    3.042538] sensor_register_slave:mma8452,id=17
[    3.047090] sensor_register_slave:lis3dh,id=7
[    3.051465] sensor_register_slave:mma7660,id=18
[    3.056126] sensor_register_slave:lsm303d,id=22
[    3.060674] sensor_register_slave:gs_mc3230,id=23
[    3.065431] [Gsensor]   gsensor_init
[    3.069067] sensor_register_slave:mpu6880_acc,id=24
[    3.074071] sensor_register_slave:mpu6500_acc,id=25
[    3.078967] sensor_register_slave:lsm330_acc,id=26
[    3.083816] sensor_register_slave:akm8975,id=30
[    3.088381] sensor_register_slave:akm8963,id=31
[    3.093024] sensor_register_slave:l3g4200d,id=45
[    3.097731] sensor_register_slave:l3g20d,id=46
[    3.102256] sensor_register_slave:ewtsa,id=47
[    3.106751] sensor_register_slave:lsm330_gyro,id=51
[    3.111714] sensor_register_slave:cm3217,id=53
[    3.111740] usb 1-1: New USB device found, idVendor=1a40, idProduct=0201
[    3.111754] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    3.111763] usb 1-1: Product: USB 2.0 Hub [MTT]
[    3.116599] hub 1-1:1.0: USB hub found
[    3.123092] hub 1-1:1.0: 7 ports detected
[    3.142673] sensor_register_slave:cm3218,id=54
[    3.148975] i2c /dev entries driver
[    3.154281] fan53555-regulator 0-0040: GPIO lookup for consumer vsel
[    3.154307] fan53555-regulator 0-0040: using device tree for GPIO lookup
[    3.154329] of_get_named_gpiod_flags: can't parse 'vsel-gpios' property of node '/i2c@ff650000/syr827@40[0]'
[    3.154349] of_get_named_gpiod_flags: can't parse 'vsel-gpio' property of node '/i2c@ff650000/syr827@40[0]'
[    3.154366] fan53555-regulator 0-0040: using lookup tables for GPIO lookup
[    3.154385] fan53555-regulator 0-0040: lookup for GPIO vsel failed
[    3.154848] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
[    3.161837] fan53555-reg: supplied by vcc_sys
[    3.169119] fan53555-regulator 0-0041: GPIO lookup for consumer vsel
[    3.169145] fan53555-regulator 0-0041: using device tree for GPIO lookup
[    3.169167] of_get_named_gpiod_flags: can't parse 'vsel-gpios' property of node '/i2c@ff650000/syr828@41[0]'
[    3.169187] of_get_named_gpiod_flags: can't parse 'vsel-gpio' property of node '/i2c@ff650000/syr828@41[0]'
[    3.169205] fan53555-regulator 0-0041: using lookup tables for GPIO lookup
[    3.169223] fan53555-regulator 0-0041: lookup for GPIO vsel failed
[    3.169683] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected!
[    3.176712] fan53555-reg: supplied by vcc_sys
[    3.187319] rtc-hym8563 0-0051: rtc core: registered hym8563 as rtc0
[    3.195298] REG1: supplied by vcc_sys
[    3.200614] REG2: supplied by vcc_sys
[    3.205734] vcc_flash: supplied by vcc_io
[    3.210065] vcc_sd: supplied by vcc_io
[    3.214166] vcc28_dvp: supplied by vcc_io
[    3.218528] dovdd_1v8: supplied by vcc28_dvp
[    3.223078] REG3: supplied by vcc_sys
[    3.228367] REG4: supplied by vcc_sys
[    3.233549] REG5: supplied by vcc_sys
[    3.238891] REG6: supplied by vcc_sys
[    3.244523] REG7: supplied by vcc_sys
[    3.249671] REG8: supplied by vcc_sys
[    3.254911] REG9: supplied by vcc_sys
[    3.260010] REG10: supplied by vcc_20
[    3.265336] REG11: supplied by vcc_20
[    3.270643] REG12: supplied by vcc_20
[    3.275993] rk3x-i2c ff650000.i2c: Initialized RK3xxx I2C bus at f120c000
[    3.284194] rk3x-i2c ff140000.i2c: Initialized RK3xxx I2C bus at f120e000
[    3.292013] rk3x-i2c ff150000.i2c: Initialized RK3xxx I2C bus at f1210000
[    3.299894] rk3x-i2c ff160000.i2c: Initialized RK3xxx I2C bus at f1212000
[    3.308188] rk3x-i2c ff660000.i2c: Initialized RK3xxx I2C bus at f1214000
[    3.317624] rkisp1 ff910000.rkisp1: rkisp1 driver version: v00.01.05
[    3.324102] rkisp1 ff910000.rkisp1: Missing rockchip,grf property
[    3.332875] rkisp1 ff910000.rkisp1: GPIO lookup for consumer vsirq
[    3.332902] rkisp1 ff910000.rkisp1: using device tree for GPIO lookup
[    3.332925] of_get_named_gpiod_flags: can't parse 'vsirq-gpios' property of node '/rkisp1@ff910000[0]'
[    3.332945] of_get_named_gpiod_flags: can't parse 'vsirq-gpio' property of node '/rkisp1@ff910000[0]'
[    3.332963] rkisp1 ff910000.rkisp1: using lookup tables for GPIO lookup
[    3.332981] rkisp1 ff910000.rkisp1: lookup for GPIO vsirq failed
[    3.333961] usbcore: registered new interface driver uvcvideo
[    3.339739] USB Video Class driver (1.1.1)
[    3.349517] Boot mode: normal
[    3.354089] rockchip-thermal ff280000.tsadc: Missing rockchip,grf property
[    3.361104] rk_tsadcv2_temp_to_code: Invalid conversion table: code=4095, temperature=2147483647
[    3.370390] rockchip-thermal ff280000.tsadc: tsadc is probed successfully!
[    3.379267] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[    3.388176] Bluetooth: Virtual HCI driver ver 1.5
[    3.393273] Bluetooth: HCI UART driver ver 2.3
[    3.397753] Bluetooth: HCI UART protocol H4 registered
[    3.402965] Bluetooth: HCI UART protocol LL registered
[    3.408123] Bluetooth: HCI UART protocol ATH3K registered
[    3.413729] usbcore: registered new interface driver bfusb
[    3.419388] usbcore: registered new interface driver btusb
[    3.422496] usb 1-1.6: new low-speed USB device number 3 using dwc2
[    3.432636] cpu cpu0: bin=1
[    3.435683] cpu cpu0: leakage=28
[    3.452406] cpu cpu0: temp=52916, pvtm=17609 (17915 + -306)
[    3.459134] rockchip_cpuclk_pre_rate_change: Invalid rate : 500000000 for cpuclk
[    3.466712] cpu cpu0: pvtm-volt-sel=3
[    3.470597] cpu cpu0: bin-scale=25
[    3.477171] cpu cpu0: avs=0
[    3.480123] cpu cpu0: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0
[    3.487198] cpu cpu0: failed to read out thermal zone (-22)
[    3.494319] cpu cpu0: failed to find power_model node
[    3.499896] sdhci: Secure Digital Host Controller Interface driver
[    3.506188] sdhci: Copyright(c) Pierre Ossman
[    3.510582] Synopsys Designware Multimedia Card Interface Driver
[    3.518183] dwmmc_rockchip ff0c0000.dwmmc: IDMAC supports 32-bit address mode.
[    3.525675] dwmmc_rockchip ff0c0000.dwmmc: Using internal DMA controller.
[    3.532499] dwmmc_rockchip ff0c0000.dwmmc: Version ID is 270a
[    3.538291] dwmmc_rockchip ff0c0000.dwmmc: DW MMC controller at irq 29,32 bit host data width,256 deep fifo
[    3.548248] dwmmc_rockchip ff0c0000.dwmmc: 'clock-freq-min-max' property was deprecated.
[    3.557599] dwmmc_rockchip ff0c0000.dwmmc: GPIO lookup for consumer cd
[    3.557643] dwmmc_rockchip ff0c0000.dwmmc: using device tree for GPIO lookup
[    3.557694] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/dwmmc@ff0c0000[0]'
[    3.557735] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/dwmmc@ff0c0000[0]'
[    3.557785] dwmmc_rockchip ff0c0000.dwmmc: using lookup tables for GPIO lookup
[    3.557825] dwmmc_rockchip ff0c0000.dwmmc: lookup for GPIO cd failed
[    3.557876] dwmmc_rockchip ff0c0000.dwmmc: GPIO lookup for consumer wp
[    3.557919] dwmmc_rockchip ff0c0000.dwmmc: using device tree for GPIO lookup
[    3.557952] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/dwmmc@ff0c0000[0]'
[    3.557993] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/dwmmc@ff0c0000[0]'
[    3.558034] dwmmc_rockchip ff0c0000.dwmmc: using lookup tables for GPIO lookup
[    3.558074] dwmmc_rockchip ff0c0000.dwmmc: lookup for GPIO wp failed
[    3.560079] usb 1-1.6: New USB device found, idVendor=046d, idProduct=c05a
[    3.566971] usb 1-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    3.574287] usb 1-1.6: Product: USB Optical Mouse
[    3.578988] usb 1-1.6: Manufacturer: Logitech
[    3.662825] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000 done
[    3.670447] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000 done
[    3.682426] usb 1-1.7: new low-speed USB device number 4 using dwc2
[    3.690488] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    3.712361] dwmmc_rockchip ff0c0000.dwmmc: 1 slots initialized
[    3.718724] dwmmc_rockchip ff0d0000.dwmmc: IDMAC supports 32-bit address mode.
[    3.726076] dwmmc_rockchip ff0d0000.dwmmc: Using internal DMA controller.
[    3.732896] dwmmc_rockchip ff0d0000.dwmmc: Version ID is 270a
[    3.738692] dwmmc_rockchip ff0d0000.dwmmc: DW MMC controller at irq 30,32 bit host data width,256 deep fifo
[    3.748465] dwmmc_rockchip ff0d0000.dwmmc: 'clock-freq-min-max' property was deprecated.
[    3.756623] dwmmc_rockchip ff0d0000.dwmmc: No vmmc regulator found
[    3.762823] dwmmc_rockchip ff0d0000.dwmmc: No vqmmc regulator found
[    3.769103] dwmmc_rockchip ff0d0000.dwmmc: GPIO lookup for consumer wp
[    3.769113] dwmmc_rockchip ff0d0000.dwmmc: using device tree for GPIO lookup
[    3.769123] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/dwmmc@ff0d0000[0]'
[    3.769132] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/dwmmc@ff0d0000[0]'
[    3.769141] dwmmc_rockchip ff0d0000.dwmmc: using lookup tables for GPIO lookup
[    3.769155] dwmmc_rockchip ff0d0000.dwmmc: lookup for GPIO wp failed
[    3.769307] platform sdio-pwrseq: GPIO lookup for consumer reset
[    3.769318] platform sdio-pwrseq: using device tree for GPIO lookup
[    3.769342] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/sdio-pwrseq[0]' - status (0)
[    3.769391] dwmmc_rockchip ff0d0000.dwmmc: allocated mmc-pwrseq
[    3.788110] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    3.808304] usb 1-1.7: New USB device found, idVendor=1c4f, idProduct=0002
[    3.809953] dwmmc_rockchip ff0d0000.dwmmc: 1 slots initialized
[    3.810363] dwmmc_rockchip ff0f0000.dwmmc: IDMAC supports 32-bit address mode.
[    3.810394] dwmmc_rockchip ff0f0000.dwmmc: Using internal DMA controller.
[    3.810407] dwmmc_rockchip ff0f0000.dwmmc: Version ID is 270a
[    3.810436] dwmmc_rockchip ff0f0000.dwmmc: DW MMC controller at irq 31,32 bit host data width,256 deep fifo
[    3.810447] dwmmc_rockchip ff0f0000.dwmmc: 'clock-freq-min-max' property was deprecated.
[    3.810474] dwmmc_rockchip ff0f0000.dwmmc: No vmmc regulator found
[    3.810477] dwmmc_rockchip ff0f0000.dwmmc: No vqmmc regulator found
[    3.810486] dwmmc_rockchip ff0f0000.dwmmc: GPIO lookup for consumer wp
[    3.810489] dwmmc_rockchip ff0f0000.dwmmc: using device tree for GPIO lookup
[    3.810494] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/dwmmc@ff0f0000[0]'
[    3.810498] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/dwmmc@ff0f0000[0]'
[    3.810501] dwmmc_rockchip ff0f0000.dwmmc: using lookup tables for GPIO lookup
[    3.810505] dwmmc_rockchip ff0f0000.dwmmc: lookup for GPIO wp failed
[    3.823159] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    3.835848] dwmmc_rockchip ff0f0000.dwmmc: 1 slots initialized
[    3.836087] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.836268] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/work[0]' - status (0)
[    3.836435] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/user[0]' - status (0)
[    3.836784] hidraw: raw HID events driver (C) Jiri Kosina
[    3.839933] input: Logitech USB Optical Mouse as /devices/platform/ff540000.usb/usb1/1-1/1-1.6/1-1.6:1.0/0003:046D:C05A.0001/input/input1
[    3.840224] hid-generic 0003:046D:C05A.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-ff540000.usb-1.6/input0
[    3.840281] usbcore: registered new interface driver usbhid
[    3.840283] usbhid: USB HID core driver
[    3.840590] ashmem: initialized
[    3.841260] rockchip-dmc dmc: unable to get devfreq-event device : dfi
[    3.842736] rknandbase v1.2 2018-05-08
[    3.842921] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[    3.843414] usbcore: registered new interface driver snd-usb-audio
[    3.844271] of_get_named_gpiod_flags: parsed 'spk-ctl-gpio' property of node '/i2c@ff660000/es8323@10[0]' - status (0)
[    3.844313] of_get_named_gpiod_flags: parsed 'hp-ctl-gpio' property of node '/i2c@ff660000/es8323@10[0]' - status (0)
[    3.844348] of_get_named_gpiod_flags: parsed 'hp-det-gpio' property of node '/i2c@ff660000/es8323@10[0]' - status (0)
[    3.844496] of_get_named_gpiod_flags: parsed 'aux-det-gpio' property of node '/i2c@ff660000/es8323@10[0]' - status (0)
[    3.844578] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    3.846416] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    3.847605] u32 classifier
[    3.847612] Netfilter messages via NETLINK v0.30.
[    3.847664] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[    3.847941] ctnetlink v0.93: registering with nfnetlink.
[    3.848051] ip_set: protocol 6
[    3.848060] IPVS: Registered protocols ()
[    3.848092] IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
[    3.848201] IPVS: Creating netns size=1104 id=0
[    3.848230] IPVS: ipvs loaded.
[    3.848530] ip_tables: (C) 2000-2006 Netfilter Core Team
[    3.848792] Initializing XFRM netlink socket
[    3.849379] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[    3.849500] NET: Registered protocol family 10
[    3.850129] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    3.850266] sit: IPv6 over IPv4 tunneling driver
[    3.850792] NET: Registered protocol family 17
[    3.850824] NET: Registered protocol family 15
[    3.850877] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    3.850905] Bridge firewalling registered
[    3.851003] Bluetooth: RFCOMM socket layer initialized
[    3.851020] Bluetooth: RFCOMM ver 1.11
[    3.851039] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    3.851046] Bluetooth: HIDP socket layer initialized
[    3.851099] 8021q: 802.1Q VLAN Support v1.8
[    3.851116] lib80211: common routines for IEEE802.11 drivers
[    3.851119] lib80211_crypt: registered algorithm 'NULL'
[    3.851125] lib80211_crypt: registered algorithm 'WEP'
[    3.851131] lib80211_crypt: registered algorithm 'CCMP'
[    3.851136] lib80211_crypt: registered algorithm 'TKIP'
[    3.851143] [WLAN_RFKILL]: Enter rfkill_wlan_init
[    3.851434] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[    3.851452] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6212
[    3.851454] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[    3.851456] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[    3.851460] of_get_named_gpiod_flags: can't parse 'WIFI,poweren_gpio' property of node '/wireless-wlan[0]'
[    3.851463] of_get_named_gpiod_flags: can't parse 'WIFI,vbat_gpio' property of node '/wireless-wlan[0]'
[    3.851466] of_get_named_gpiod_flags: can't parse 'WIFI,reset_gpio' property of node '/wireless-wlan[0]'
[    3.851490] of_get_named_gpiod_flags: parsed 'WIFI,host_wake_irq' property of node '/wireless-wlan[0]' - status (0)
[    3.851493] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 150, flags = 0.
[    3.851498] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[    3.851500] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[    3.851504] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[    3.851556] [BT_RFKILL]: Enter rfkill_rk_init
[    3.851840] of_get_named_gpiod_flags: parsed 'uart_rts_gpios' property of node '/wireless-bluetooth[0]' - status (0)
[    3.851843] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 139.
[    3.851849] of_get_named_gpiod_flags: can't parse 'BT,power_gpio' property of node '/wireless-bluetooth[0]'
[    3.851862] of_get_named_gpiod_flags: parsed 'BT,reset_gpio' property of node '/wireless-bluetooth[0]' - status (0)
[    3.851864] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 149.
[    3.851875] of_get_named_gpiod_flags: parsed 'BT,wake_gpio' property of node '/wireless-bluetooth[0]' - status (0)
[    3.851878] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 146.
[    3.851889] of_get_named_gpiod_flags: parsed 'BT,wake_host_irq' property of node '/wireless-bluetooth[0]' - status (0)
[    3.851891] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 151.
[    3.851894] [BT_RFKILL]: bluetooth_platdata_parse_dt: clk_get failed!!!.
[    3.851941] [BT_RFKILL]: Request irq for bt wakeup host
[    3.851973] [BT_RFKILL]: ** disable irq
[    3.852102] [BT_RFKILL]: bt_default device registered.
[    3.852162] Key type dns_resolver registered
[    3.852249] sensor_register_slave:mpu6880_gyro,id=50
[    3.852596] tc35874x 1-000f: driver version: 00.01.00
[    3.852675] tc35874x 1-000f: GPIO lookup for consumer reset
[    3.852678] tc35874x 1-000f: using device tree for GPIO lookup
[    3.852696] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/i2c@ff140000/tc358749@0f[0]' - status (0)
[    3.852951] mmc1: queuing unknown CIS tuple 0x81 (9 bytes)
[    3.868439] mmc_host mmc2: Bus speed (slot 0) = 99000000Hz (slot req 100000000Hz, actual 99000000HZ div = 0)
[    3.903551] rkisp1: Async subdev notifier completed
[    3.903584] mmc_host mmc1: Bus speed (slot 0) = 49500000Hz (slot req 50000000Hz, actual 49500000HZ div = 0)
[    3.928852] m00_b_tc35874x 1-000f: tc358749 found @ 0x1e (rk3x-i2c)
[    3.929288] ThumbEE CPU extension supported.
[    3.929298] Registering SWP/SWPB emulation handler
[    3.929704] Loading compiled-in X.509 certificates
[    3.930360] mali ffa30000.gpu: bin=0
[    3.930373] mali ffa30000.gpu: Failed to get leakage
[    3.930525] mali ffa30000.gpu: Failed to get pvtm
[    3.930537] mali ffa30000.gpu: bin-scale=59
[    3.930725] mali ffa30000.gpu: avs=0
[    3.930759] W : [File] : drivers/gpu/arm/midgard_for_linux/platform/rk/mali_kbase_config_rk.c; [Line] : 114; [Func] : kbase_platform_rk_init(); power-off-delay-ms not available.
[    3.930966] mali ffa30000.gpu: GPU identified as 0x0750 r1p0 status 0
[    3.931323] mali ffa30000.gpu: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0
[    3.931415] I : [File] : drivers/gpu/arm/midgard_for_linux/backend/gpu/mali_kbase_devfreq.c; [Line] : 315; [Func] : kbase_devfreq_init(); success initing power_model_simple.
[    3.931660] mali ffa30000.gpu: Probed as mali0
[    3.932451] force_sf_dma_mode is ignored if force_thresh_dma_mode is set.
[    3.932452] rk_gmac-dwmac ff290000.ethernet: clock input or output? (input).
[    3.932456] rk_gmac-dwmac ff290000.ethernet: TX delay(0x1d).
[    3.932460] rk_gmac-dwmac ff290000.ethernet: RX delay(0x16).
[    3.932470] rk_gmac-dwmac ff290000.ethernet: integrated PHY? (no).
[    3.932541] rk_gmac-dwmac ff290000.ethernet: cannot get clock clk_mac_speed
[    3.932544] rk_gmac-dwmac ff290000.ethernet: clock input from PHY
[    3.937553] rk_gmac-dwmac ff290000.ethernet: init for RGMII
[    3.937602] stmmac - user ID: 0x10, Synopsys ID: 0x35
[    3.937604]  Ring mode enabled
[    3.937606]  DMA HW capability register supported
[    3.937606]  Normal descriptors
[    3.937608]  RX Checksum Offload Engine supported (type 2)
[    3.937609]  Wake-Up On Lan supported
[    3.937631]  Enable RX Mitigation via HW Watchdog Timer
[    3.937700] of_get_named_gpiod_flags: parsed 'snps,reset-gpio' property of node '/ethernet@ff290000[0]' - status (0)
[    3.952489] devfreq ffa30000.gpu: Couldn't update frequency transition information.
[    4.059170] dwmmc_rockchip ff0f0000.dwmmc: Successfully tuned phase to 190
[    4.059225] mmc2: new HS200 MMC card at address 0001
[    4.059514] mmcblk2: mmc2:0001 AJTD4R 14.6 GiB
[    4.059647] mmcblk2boot0: mmc2:0001 AJTD4R partition 1 4.00 MiB
[    4.059769] mmcblk2boot1: mmc2:0001 AJTD4R partition 2 4.00 MiB
[    4.059880] mmcblk2rpmb: mmc2:0001 AJTD4R partition 3 4.00 MiB
[    4.061925]  mmcblk2: p1 p2 p3 p4 p5
[    4.093803] random: nonblocking pool is initialized
[    4.263189] dwmmc_rockchip ff0d0000.dwmmc: Successfully tuned phase to 125
[    4.265166] mmc1: queuing unknown CIS tuple 0x91 (3 bytes)
[    4.265184] mmc1: new ultra high speed SDR104 SDIO card at address 0001
[    4.374168] vendor storage:20190527 ret = 0
[    4.496442] usb 1-1.7: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.503751] usb 1-1.7: Product: USB Keyboard
[    4.508018] usb 1-1.7: Manufacturer: SIGMACHIP
[    4.516161] input: SIGMACHIP USB Keyboard as /devices/platform/ff540000.usb/usb1/1-1/1-1.7/1-1.7:1.0/0003:1C4F:0002.0002/input/input2
[    4.586074] hid-generic 0003:1C4F:0002.0002: input,hidraw1: USB HID v1.10 Keyboard [SIGMACHIP USB Keyboard] on usb-ff540000.usb-1.7/input0
[    4.606770] input: SIGMACHIP USB Keyboard as /devices/platform/ff540000.usb/usb1/1-1/1-1.7/1-1.7:1.1/0003:1C4F:0002.0003/input/input3
[    4.673542] hid-generic 0003:1C4F:0002.0003: input,hidraw2: USB HID v1.10 Device [SIGMACHIP USB Keyboard] on usb-ff540000.usb-1.7/input1
[    4.968954] libphy: stmmac: probed
[    4.972627] eth%d: PHY ID 001cc915 at 0 IRQ POLL (stmmac-0:00) active
[    4.979135] eth%d: PHY ID 001cc915 at 5 IRQ POLL (stmmac-0:05)
[    4.988993] input: adc-keys as /devices/platform/adc-keys/input/input4
[    5.001001] rockchip-dmc dmc: Failed to get leakage
[    5.006447] rockchip-dmc dmc: Failed to get pvtm
[    5.011840] rockchip-dmc dmc: avs=0
[    5.015439] rockchip-dmc dmc: failed to get vop bandwidth to dmc rate
[    5.021898] rockchip-dmc dmc: failed to get vop pn to msch rl
[    5.028074] rockchip-dmc dmc: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0
[    5.035796] rockchip-dmc dmc: could not find power_model node
[    5.043455] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/sound[0]'
[    5.043472] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/sound[0]'
[    5.177232] asoc-simple-card sound: ES8323 HiFi <-> ff890000.i2s mapping ok
[    5.189165] asoc-simple-card sound: i2s-hifi <-> ff890000.i2s mapping ok
[    5.196452] asoc-simple-card sound: ASoC: no sink widget found for MIC1
[    5.203110] asoc-simple-card sound: ASoC: Failed to add route Microphone Jack -> direct -> MIC1
[    5.211802] asoc-simple-card sound: ASoC: no sink widget found for MIC2
[    5.218435] asoc-simple-card sound: ASoC: Failed to add route Microphone Jack -> direct -> MIC2
[    5.227133] asoc-simple-card sound: ASoC: no source widget found for micbias1
[    5.234277] asoc-simple-card sound: ASoC: Failed to add route micbias1 -> direct -> Microphone Jack
[    5.243322] asoc-simple-card sound: ASoC: no source widget found for HPOL
[    5.250106] asoc-simple-card sound: ASoC: Failed to add route HPOL -> direct -> Headphone Jack
[    5.258721] asoc-simple-card sound: ASoC: no source widget found for HPOR
[    5.265510] asoc-simple-card sound: ASoC: Failed to add route HPOR -> direct -> Headphone Jack
[    5.276554] input: rockchip,firefly-codec Headphone Jack as /devices/platform/sound/sound/card0/input5
[    5.286174] dhd_module_init: in Dongle Host Driver, version 1.579.77.41.10 (r)

[    5.286177] =======================================================
[    5.286182] ==== Launching Wi-Fi driver! (Powered by Rockchip) ====
[    5.286191] =======================================================
[    5.286194] Realtek 8188EU USB WiFi driver (Powered by Rockchip,Ver v5.2.2.3_24783.20171030) init.
[    5.286196] [WLAN_RFKILL]: rockchip_wifi_power: 1
[    5.286199] [WLAN_RFKILL]: wifi turn on power. -1
[    5.286201] RTW: module init start
[    5.286203] RTW: rtl8188eu v5.2.2.3_24783.20171030
[    5.286205] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter
[    5.286307] usbcore: registered new interface driver rtl8188eu
[    5.286308] RTW: module init ret=0
[    5.286631] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-keys/button@0[0]' - status (0)
[    5.286668] gpio-5 (GPIO Key Power): gpiod_set_debounce: missing set() or set_debounce() operations
[    5.286838] input: gpio-keys as /devices/platform/gpio-keys/input/input6
[    5.293406] rtc-hym8563 0-0051: setting system clock to 2020-11-04 10:20:01 UTC (1604485201)
[    5.302100] vcc_sd: disabling
[    5.302271] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 417; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '14:43:21', on 'Apr  3 2020'.
[    5.302600] Mali: Mali device driver loaded
[    5.302879] ALSA device list:
[    5.302882]   #0: rockchip,firefly-codec
[    5.404411] ======== dhd_wlan_init_plat_data ========
[    5.409465] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter
[    5.415063] dhd_wlan_init_gpio: WL_HOST_WAKE=-1, oob_irq=233, oob_irq_flags=0x414
[    5.422553] dhd_wlan_init_gpio: WL_REG_ON=-1
[    5.426824] dhd_wifi_platform_load: Enter
[    5.430883] Power-up adapter 'DHD generic adapter'
[    5.435954] wifi_platform_set_power = 1
[    5.439788] ======== PULL WL_REG_ON(-1) HIGH! ========
[    5.441048] EXT4-fs (mmcblk2p5): mounted filesystem with ordered data mode. Opts: (null)
[    5.441078] VFS: Mounted root (ext4 filesystem) on device 179:5.
[    5.442249] devtmpfs: mounted
[    5.461990] [WLAN_RFKILL]: rockchip_wifi_power: 1
[    5.466695] [WLAN_RFKILL]: wifi turn on power. -1
[    5.571530] ES8323 exit line in mode
[    5.572187] Freeing unused kernel memory: 1024K
[    5.756220] cgroup: cgroup2: unknown option "nsdelegate"
[    5.772465] wifi_platform_bus_enumerate device present 1
[    5.777789] ======== Card detection to detect SDIO card! ========
[    5.777794] mmc1:mmc host rescan start!
[    5.788164] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[    5.793908] bcmsdh_register: register client driver
[    5.794104] bcmsdh_sdmmc_probe: Enter num=1
[    5.794246] bcmsdh_sdmmc_probe: Enter num=2
[    5.794250] bus num (host idx)=1, slot num (rca)=1
[    5.794254] found adapter info 'DHD generic adapter'
[    5.794345] sdioh_attach: set sd_f2_blocksize 256
[    5.794411] sdioh_attach: sd clock rate = 0
[    5.794812] dhdsdio_probe : no mutex held. set lock
[    5.794975] F1 signature read @0x18000000=0x15264345
[    5.800339] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[    5.801358] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[    5.801471] dhd_conf_set_chiprev: chip=0x4345, chiprev=6
[    5.801728] CFG80211-ERROR) wl_setup_wiphy : Registering Vendor80211
[    5.802532] CFG80211-ERROR) wl_init_prof : wl_init_prof: No profile
[    5.802758] wl_escan_attach: Enter
[    5.802796] wl_escan_init: Enter
[    5.802926] wl_create_event_handler(): thread:wl_escan_handler:8b started
[    5.802941] tsk Enter, tsk = 0xedb90170
[    5.803132] dhd_attach(): thread:dhd_watchdog_thread:8c started
[    5.803234] dhd_attach(): thread:dhd_dpc:8d started
[    5.803339] dhd_attach(): thread:dhd_rxf:8e started
[    5.803348] dhd_deferred_work_init: work queue initialized
[    5.803354] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 2
[    5.803385] dhd_bus_set_default_min_res_mask: Unhandled chip id
[    5.803683] sdioh_cis_read: func_cis_ptr[0]=0x10ac
[    5.815706] Dongle Host Driver, version 1.579.77.41.10 (r)
[    5.816242] wl_ext_iapsta_attach_netdev: ifidx=0, bssidx=0
[    5.816248] Register interface [wlan0]  MAC: cc:4b:73:76:f9:f4

[    5.816299] dhd_tcpack_suppress_set: TCP ACK Suppress mode 2 -> mode 0
[    5.816307] dhd_wl_ioctl: returning as busstate=0
[    5.816311] dhd_dbg_detach_pkt_monitor, 2204
[    5.816313] dhd_bus_devreset: == Power OFF ==
[    5.816533] bcmsdh_oob_intr_unregister: Enter
[    5.816536] bcmsdh_oob_intr_unregister: irq is not registered
[    5.816542] dhd_txglom_enable: enable 0
[    5.816544] dhd_conf_set_txglom_params: txglom_mode=copy
[    5.816547] dhd_conf_set_txglom_params: txglomsize=0, deferred_tx_len=0
[    5.816550] dhd_conf_set_txglom_params: txinrx_thres=128, dhd_txminmax=-1
[    5.816553] dhd_conf_set_txglom_params: tx_max_offset=0, txctl_tmo_fix=300
[    5.816556] dhd_bus_devreset:  WLAN OFF DONE
[    5.816596] wifi_platform_set_power = 0
[    5.816599] ======== PULL WL_REG_ON(-1) LOW! ========
[    5.816602] [WLAN_RFKILL]: rockchip_wifi_power: 0
[    5.816616] [WLAN_RFKILL]: wifi shut off power.
[    5.816619] dhdsdio_probe : the lock is released.
[    5.816676] dhd_module_init: Exit err=0
[    6.047004] systemd[1]: Detected architecture arm.
[    6.057520] systemd[1]: Set hostname to <firefly>.
[    6.166112] systemd[1]: File /lib/systemd/system/systemd-udevd.service:34 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
[    6.183078] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
[    6.412695] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    6.422043] systemd[1]: Reached target User and Group Name Lookups.
[    6.434535] systemd[1]: Reached target Swap.
[    6.444498] systemd[1]: Reached target Remote File Systems.
[    6.454851] systemd[1]: Created slice User and Session Slice.
[    6.465072] systemd[1]: Created slice System Slice.
[    6.475114] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[    6.486969] systemd[1]: Listening on Syslog Socket.
[    6.508913] systemd[1]: Reached target Slices.
[    6.513743] systemd[1]: Listening on udev Kernel Socket.
[    6.523167] systemd[1]: Created slice system-serial\x2dgetty.slice.
[    6.534230] systemd[1]: Listening on Journal Socket.
[    6.546194] systemd[1]: Starting Remount Root and Kernel File Systems...
[    6.558436] systemd[1]: Starting Load Kernel Modules...
[    6.567923] systemd[1]: Mounting Kernel Debug File System...
[    6.577411] systemd[1]: Starting Set the console keyboard layout...
[    6.588365] systemd[1]: Listening on Journal Socket (/dev/log).
[    6.598935] systemd[1]: Starting Journal Service...
[    6.609557] systemd[1]: Starting Create Static Device Nodes in /dev...
[    6.617619] systemd[1]: Listening on udev Control Socket.
[    6.629867] systemd[1]: Starting udev Coldplug all Devices...
[    6.641097] systemd[1]: Started Remount Root and Kernel File Systems.
[    6.652716] systemd[1]: Started Load Kernel Modules.
[    6.660858] systemd[1]: Mounted Kernel Debug File System.
[    6.671112] systemd[1]: Started Create Static Device Nodes in /dev.
[    6.684462] systemd[1]: Starting Apply Kernel Variables...
[    6.703406] systemd[1]: Mounting Kernel Configuration File System...
[    6.712249] systemd[1]: Mounting FUSE Control File System...
[    6.727473] systemd[1]: Starting udev Kernel Device Manager...
[    6.729523] systemd[1]: Starting Load/Save Random Seed...
[    6.738733] systemd[1]: Started Apply Kernel Variables.
[    6.743414] systemd[1]: Mounted Kernel Configuration File System.
[    6.746610] systemd[1]: Mounted FUSE Control File System.
[    6.756799] systemd[1]: Started Load/Save Random Seed.
[    6.771925] systemd[1]: Started Journal Service.
[    6.793005] systemd-journald[165]: Received request to flush runtime journal from PID 1
[    7.529395] cfg80211: World regulatory domain updated:
[    7.529407] cfg80211:  DFS Master region: unset
[    7.529413] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[    7.529421] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[    7.529428] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[    7.529434] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[    7.529441] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[    7.529447] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[    7.529453] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[    7.529458] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[    7.529463] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[    7.977234] [BT_RFKILL]: rfkill_rk_set_power: set bt wake_host high!
[    8.032494] [BT_RFKILL]: ENABLE UART_RTS
[    8.142516] [BT_RFKILL]: DISABLE UART_RTS
[    8.142573] [BT_RFKILL]: bt turn on power
[    8.142656] [BT_RFKILL]: Request irq for bt wakeup host
[    8.142697] [BT_RFKILL]: ** disable irq
[    8.217344] ttyS0 - failed to request DMA, use interrupt mode
[    8.315973] IPVS: Creating netns size=1104 id=1
[    8.583376] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[    8.583544] dhd_open: Enter edb31000
[    8.583550] dhd_open : no mutex held. set lock
[    8.583558]
               Dongle Host Driver, version 1.579.77.41.10 (r)
[    8.583565] wl_ext_iapsta_attach_netdev: ifidx=0, bssidx=0
[    8.583569] wl_android_wifi_on in 1
[    8.583574] wl_android_wifi_on in 2: g_wifi_on=0
[    8.583579] wifi_platform_set_power = 1
[    8.583583] ======== PULL WL_REG_ON(-1) HIGH! ========
[    8.583588] [WLAN_RFKILL]: rockchip_wifi_power: 1
[    8.583594] [WLAN_RFKILL]: wifi turn on power. -1
[    8.892610] sdio_reset_comm():
[    8.908425] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    8.926263] mmc_host mmc1: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0)
[    8.980278] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[    8.984432] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    8.988179] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    8.994896] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[    9.002981] mmc1: queuing unknown CIS tuple 0x81 (9 bytes)
[    9.126721] mmc_host mmc1: Bus speed (slot 0) = 49500000Hz (slot req 50000000Hz, actual 49500000HZ div = 0)
[    9.540496] dwmmc_rockchip ff0d0000.dwmmc: Successfully tuned phase to 125
[    9.540943] sdioh_start: set sd_f2_blocksize 256
[    9.543715]
               
               dhd_bus_devreset: == WLAN ON ==
[    9.545015] F1 signature read @0x18000000=0x15264345
[    9.565692] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[    9.566271] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[    9.566332] dhd_bus_set_default_min_res_mask: Unhandled chip id
[    9.567826] dhd_os_open_image: /system/etc/firmware/config.txt (205 bytes) open success
[    9.568092] dhd_conf_read_others: regrev = 0
[    9.568104] dhd_conf_read_sdio_params: dhd_doflow = 1
[    9.568114] dhd_conf_read_others: srl = 15
[    9.568123] dhd_conf_read_others: lrl = 15
[    9.568140] Final fw_path=/system/etc/firmware/fw_bcm43455c0_ag.bin
[    9.568146] Final nv_path=/system/etc/firmware/nvram_ap6255.txt
[    9.568152] Final clm_path=/system/etc/firmware/clm.blob
[    9.568158] Final conf_path=/system/etc/firmware/config.txt
[    9.568591] dhd_os_open_image: /system/etc/firmware/fw_bcm43455c0_ag.bin (483181 bytes) open success
[    9.635272] dhd_os_open_image: /system/etc/firmware/nvram_ap6255.txt (1644 bytes) open success
[    9.635645] NVRAM version: AP6255_NVRAM_V1.0_29052015
[    9.636410] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
[    9.715187] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
[    9.716112] bcmsdh_oob_intr_register: HW_OOB irq=233 flags=0x4
[    9.717265] dhd_get_memdump_info: File [/data/misc/wifi/.memdump.info] doesn't exist
[    9.717339] dhd_get_memdump_info: MEMDUMP ENABLED = 2
[    9.725040] Disable tdls_auto_op failed. -1
[    9.725129] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 1
[    9.727765] dhd_apply_default_clm: Ignore clm file /system/etc/firmware/clm.blob
[    9.734949] Firmware up: op_mode=0x0005, MAC=cc:4b:73:76:f9:f4
[    9.745347] dhd_preinit_ioctls Set scancache failed -23
[    9.752023]   Driver: 1.579.77.41.10 (r)
                 Firmware: wl0: Aug 25 2015 18:58:57 version 7.45.69 (r581703) FWID 01-24037f6e
                 CLM: 7.14.8
[    9.752255] dhd_txglom_enable: enable 1
[    9.752264] dhd_conf_set_txglom_params: txglom_mode=copy
[    9.752271] dhd_conf_set_txglom_params: txglomsize=36, deferred_tx_len=0
[    9.752279] dhd_conf_set_txglom_params: txinrx_thres=128, dhd_txminmax=-1
[    9.752286] dhd_conf_set_txglom_params: tx_max_offset=0, txctl_tmo_fix=300
[    9.752298] dhd_conf_get_disable_proptx: fw_proptx=1, disable_proptx=-1
[    9.753099] dhd_wlfc_hostreorder_init(): successful bdcv2 tlv signaling, 64
[    9.782727] rk_gmac-dwmac ff290000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[    9.791680] CFG80211-ERROR) wl_cfg80211_event : Event handler is not created
[    9.792190] rtt_do_get_ioctl: failed to send getbuf proxd iovar (CMD ID : 1), status=-23
[    9.792200] dhd_rtt_init : FTM is not supported
[    9.792209] dhd_preinit_ioctls: SensorHub diabled 0
[    9.792742] dhd_preinit_ioctls failed to set ShubHub disable
[    9.793260] dhd_ndo_get_version: failed, retcode = -23
[    9.793831] dhd_wl_ioctl_get_intiovar: get int iovar wnm_bsstrans_resp failed, ERR -23
[    9.793839] failed to get wnm_bsstrans_resp
[    9.794315] failed to set WNM capabilities
[    9.794592] dhd_conf_set_country: set country CN, revision 0
[    9.794601] CFG80211-ERROR) wl_cfg80211_event : Event handler is not created
[    9.797030] Country code: CN (CN/0)
[    9.800083] CONFIG-ERROR) dhd_conf_set_intiovar: txbf setting failed -23
[    9.807408] wl_android_wifi_on: Success
[    9.851333] CFG80211-ERROR) __wl_update_wiphybands : error reading txbf_bfe_cap (-23)
[    9.852114] CFG80211-ERROR) __wl_update_wiphybands : error reading txbf_bfr_cap (-23)
[    9.867882] dhd_open : the lock is released.
[    9.867906] dhd_open: Exit ret=0
[   10.027373] P2P interface registered
[   10.027391] wl_cfgp2p_add_p2p_disc_if: wdev: ed3d4c00, wdev->net:   (null)
[   10.043885] WLC_E_IF: NO_IF set, event Ignored
[   10.045274] P2P interface started
[   10.357358] tty_port_close_start: tty->count = 1 port count = 2.
[   12.286358] Freeing drm_logo memory: 616K
[   14.035048] IPVS: Creating netns size=1104 id=2
[   14.113806] i2s_frac p_rate(371250000) is low than rate(22579200)*20, use integer or half-div
[   19.305338] i2s_frac p_rate(371250000) is low than rate(22579200)*20, use integer or half-div
[   19.334417] i2s_frac p_rate(371250000) is low than rate(22579200)*20, use integer or half-div
[   19.339259] i2s_frac p_rate(371250000) is low than rate(22579200)*20, use integer or half-div
[   19.491090] i2s_frac p_rate(371250000) is low than rate(22579200)*20, use integer or half-div
[   19.605177] i2s_frac p_rate(371250000) is low than rate(22579200)*20, use integer or half-div
[   19.687461] i2s_frac p_rate(371250000) is low than rate(22579200)*20, use integer or half-div
[   19.697628] i2s_frac p_rate(371250000) is low than rate(22579200)*20, use integer or half-div
[   19.728125] i2s_frac p_rate(371250000) is low than rate(22579200)*20, use integer or half-div
[   19.818000] i2s_frac p_rate(371250000) is low than rate(22579200)*20, use integer or half-div
[   19.828136] i2s_frac p_rate(371250000) is low than rate(22579200)*20, use integer or half-div
[   19.915055] i2s_frac p_rate(371250000) is low than rate(22579200)*20, use integer or half-div
[   20.035300] i2s_frac p_rate(371250000) is low than rate(22579200)*20, use integer or half-div

dmesg-2.txt 和1比其实就增了2行[   38.430750] m00_b_tc35874x 1-000f: tc35874x_format_change: New format: 1920x1080p60.0 (2200x1125)[   38.516879] m00_b_tc35874x 1-000f: tc35874x_format_change: New format: 1920x1080p60.0 (2200x1125)



微信图片_20201104182804.jpg (88.22 KB, 下载次数: 193)

微信图片_20201104182804.jpg

微信图片_20201104182748.jpg (142.08 KB, 下载次数: 183)

微信图片_20201104182748.jpg

微信图片_20201104182800.jpg (115.81 KB, 下载次数: 194)

微信图片_20201104182800.jpg
回复

使用道具 举报

1306

积分

0

威望

0

贡献

中级创客

Rank: 4

积分
1306
发表于 2020-11-5 10:01:49        只看该作者  沙发
执行脚本 /usr/local/bin/test_hdmiin.sh 获取 hdmiin 输入。
回复

使用道具 举报

25

积分

0

威望

0

贡献

技术小白

积分
25
发表于 2020-11-5 10:12:06        只看该作者  板凳
[ 本帖最后由 warrior.li 于 2020-11-5 10:17 编辑 ]\n\n[ 本帖最后由 warrior.li 于 2020-11-5 10:13 编辑 ]\n\n更新一下,我看到另外一个帖子下用
/usr/local/bin
下的脚本,可以成功
但是使用的是 gst-launch-1.0 命令

我想问下如果想通过该命令推送 rtsp 视频流到 ffserver 或者rtmp到server 应该怎么写这个参数?


关于反复执行,使用ctrl+c 是OK的可以再次执行
回复

使用道具 举报

25

积分

0

威望

0

贡献

技术小白

积分
25
发表于 2020-11-5 10:35:10        只看该作者  地板
请问有没有C的DEMO能直接获取一帧图像数据的?提供的脚本封太多层了
回复

使用道具 举报

25

积分

0

威望

0

贡献

技术小白

积分
25
发表于 2020-11-5 11:05:41        只看该作者  5#
试了一下以前的一个C的demo
打开设备之后
struct v4l2_format fmt;
fmt.type = V4L2_BUF_TYPE_VIDEO_CAPTURE;

ret=xioctl(fd, VIDIOC_G_FMT, &fmt);
if(ret<0)
{
        printf("%d %s #ERR VIDIOC_G_FMT ret %d\n",\
                                __LINE__,__func__,ret);
        return -3;
}

这里就直接返回了,原来的代码是通过这个函数获得摄像头的长宽,下一步要申请buf的
这一步就已经挂了
回复

使用道具 举报

1306

积分

0

威望

0

贡献

中级创客

Rank: 4

积分
1306
发表于 2020-11-5 11:11:55        只看该作者  6#
1、gst-launch 命令可以网上找下,通常都有相关说明;
2、获取原理和摄像头是一样的,具体可以看下 `rk3288/external/camera_engine_rkisp/apps/rkisp_demo`,也可以找下摄像头的相关代码;
回复

使用道具 举报

25

积分

0

威望

0

贡献

技术小白

积分
25
发表于 2020-11-5 11:20:58        只看该作者  7#
[ 本帖最后由 warrior.li 于 2020-11-5 11:22 编辑 ]\n\n刚看到楼上的回复,我先看一下,谢谢!
=============================我使用的例子是 v4l2grabhttps://github.com/twam/v4l2grab./configuremake之后执行./v4l2grab  -d /dev/video0  -o test.jpg如果是标准摄像头可以直接获得图片
这里反正是不太行我的例子是从 v4l2grab里改出来的
想问下有没有类似的 demo
最要紧的其实还是推流,截图倒是其次
执行是这样的结果
root@firefly:/home/firefly/v4l2grab/v4l2grab-master# ./v4l2grab -d /dev/video0 -o test.jpg
Using mplane plugin for capture
Unable to set frame interval.
libv4l2: error dequeuing buf: Resource temporarily unavailable
libv4l2: error dequeuing buf: Resource temporarily unavailable
libv4l2: error dequeuing buf: Resource temporarily unavailable
libv4l2: error dequeuing buf: Resource temporarily unavailable
libv4l2: error dequeuing buf: Resource temporarily unavailable
libv4l2: error dequeuing buf: Resource temporarily unavailable
libv4l2: error dequeuing buf: Resource temporarily unavailable
libv4l2: error dequeuing buf: Resource temporarily unavailable


回复

使用道具 举报

1306

积分

0

威望

0

贡献

中级创客

Rank: 4

积分
1306
发表于 2020-11-5 13:28:45        只看该作者  8#
由于 rk 的 v4l2 不是标准接口,具体的调用细节要根据 `rk3288/external/camera_engine_rkisp/apps/rkisp_demo` 做修改
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

友情链接 : 爱板网 电子发烧友论坛 云汉电子社区 粤ICP备14022046号-2
快速回复 返回顶部 返回列表