|
|
【Linux】
Linux的固件无法引导kernel
发表于 2021-1-4 18:21:50
浏览：9340
|
回复：8
打印
只看该作者
[复制链接]
楼主
1. 编译过程：使用了官方Firefly RK3288的最新linux SDK ，所有流程都按官方的wiki走的，最后编译的大固件在/home/dev/proj/firefly-sdk/rockdev/pack/ 下 FIREFLY-RK3288-UBUNTUUBUNTU-GPT-20210104-1557.img
2. 烧写过程： 开发板上跑的是官方的GPT固件，我使用了瑞芯微开发工具v2.5.8 进入maskrom模式，烧录上述固件，烧录成功
3. 问题： 设备无法引导kernel，错误显示无法分配kernel，是不是我的操作过程有什么问题
?DDR Version 1.08 20190523
In
Channel a: DDR3 400MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 400MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Memory OK
Memory OK
OUT
Boot1 Release Time: Nov 27 2019 15:30:08, version: 2.58
ChipType = 0x8, 250
mmc2:cmd19,100
SdmmcInit=2 0
BootCapSize=2000
UserCapSize=14910MB
FwPartOffset=2000 , 2000
mmc0:cmd8,400
mmc0:cmd8,400
mmc0:cmd8,400
SdmmcInit=0 1
StorageInit ok = 27115
SecureMode = 0
SecureInit read PBA: 0x4
SecureInit read PBA: 0x404
SecureInit read PBA: 0x804
SecureInit read PBA: 0xc04
SecureInit read PBA: 0x1004
SecureInit read PBA: 0x1404
SecureInit read PBA: 0x1804
SecureInit read PBA: 0x1c04
SecureInit ret = 0, SecureMode = 0
atags_set_bootdev: ret:(0)
GPT part: 0, name: uboot, start:0x4000, size:0x2000
GPT part: 1, name: trust, start:0x6000, size:0x2000
GPT part: 2, name: misc, start:0x8000, size:0x2000
GPT part: 3, name: boot, start:0xa000, size:0x10000
GPT part: 4, name: recovery, start:0x1a000, size:0x10000
GPT part: 5, name: backup, start:0x2a000, size:0x10000
GPT part: 6, name: rootfs, start:0x5a000, size:0x3a9200
GPT part: 7, name: userdata, start:0x403200, size:0x191bddf
find part:uboot OK. first_lba:0x4000.
find part:trust OK. first_lba:0x6000.
LOADER Check OK! 0x4000, 134656
TOS Check OK! 0x6000, 171065
Enter Trust OS
INF [0x0] TEE-CORE:init_primary_helper:385: Core0 Initializing (1.1.0-432-gc99a453d #4 Mon Aug 17 09:16:49 UTC 2020 arm)
INF [0x0] TEE-CORE:init_primary_helper:386: Release version: 1.3
INF [0x0] TEE-CORE:init_primary_helper:387: Next entry point address: 0x200000
INF [0x0] TEE-CORE:init_teecore:83: teecore inits done
U-Boot 2017.09 (Jan 04 2021 - 15:56:51 +0800)
Model: Firefly-RK3288
PreSerial: 2
DRAM: 2 GiB
Sysmem: init
Relocation Offset is: 00000000
I2c speed: 400000Hz
MMC: dwmmc@ff0c0000: 1, dwmmc@ff0f0000: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Model: Firefly-RK3288
Bootdev(atags): mmc 0
volume up: read 'keyup-threshold-microvolt' failed, ret=-61
volume up: read 'keyup-threshold-microvolt' failed, ret=-61
MMC0: High Speed, 52Mhz
PartType: EFI
boot mode: None
CLK: (sync kernel. arm: enter 1000000 KHz, init 1000000 KHz, kernel 0N/A)
apll 1000000 KHz
dpll 396000 KHz
cpll 384000 KHz
gpll 594000 KHz
npll 24000 KHz
aclk_bus 297000 KHz
Net:
Warning: ethernet@ff290000 (eth0) using random MAC address - 6a:67:0f:94:23:ed
eth0: ethernet@ff290000
Hit key to stop autoboot('CTRL+C'): 0
ANDROID: reboot reason: "(none)"
Load FDT from boot part
DTB: rk-kernel.dtb
Booting ZIMAGE kernel at 0x02008000(Uncompress to 0) with fdt at 0x8300000...
ERROR: Failed to allocate 0x1188000 bytes below 0x1188000.
Sysmem Error: Failed to alloc "UNCOMPRESS-KERNEL" at 0x00000000 - 0x01188000
## Booting Android Image at 0x02007800 ...
Kernel load addr 0x02008000 size 8079 KiB
RAM disk load addr 0x0a200000 size 8675 KiB
## Flattened Device Tree blob at 08300000
Booting using the fdt blob at 0x8300000
XIP Kernel Image ... OK
'reserved-memory' dma-unusable@fe000000: addr=fe000000 size=1000000
'reserved-memory' ramoops@00000000: addr=8000000 size=f0000
Loading Ramdisk to 0f787000, end 0ffff94e ... OK
Loading Device Tree to 0f770000, end 0f786136 ... OK
Adding bank: 0x00000000 - 0x08400000 (size: 0x08400000)
Adding bank: 0x09310000 - 0x80000000 (size: 0x76cf0000)
Total: 4181.958 ms
Starting kernel ...
|
|
