|
|
发表于 2021-12-7 15:40:05
只看该作者
14#
大佬，我在自己做的板子上运行，跑不起来，启动日志如下：
DDR Version V1.11 20211103
In
ddrconfig:7
LP4 MR14:0x4d
LPDDR4, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=8192MB
tdqss: cs0 dqs0: 385ps, dqs1: 337ps, dqs2: 385ps, dqs3: 337ps,
tdqss: cs1 dqs0: 385ps, dqs1: 313ps, dqs2: 361ps, dqs3: 313ps,
change to: 324MHz
PHY drv:clk:38,ca:38,DQ:30,odt:0
vrefinner:41%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58
change to: 528MHz
PHY drv:clk:38,ca:38,DQ:30,odt:0
vrefinner:41%, vrefout:41%
dram drv:40,odt:0
clk skew:0x79
change to: 780MHz
PHY drv:clk:38,ca:38,DQ:30,odt:0
vrefinner:41%, vrefout:41%
dram drv:40,odt:0
clk skew:0x5f
change to: 1560MHz(final freq)
PHY drv:clk:38,ca:38,DQ:30,odt:60
vrefinner:16%, vrefout:29%
dram drv:40,odt:80
vref_ca:00000068
clk skew:0x18
cs 0:
the read training result:
DQS0:0x34, DQS1:0x34, DQS2:0x32, DQS3:0x34,
min : 0x6 0x5 0x9 0x2 0x5 0x6 0x5 0xd , 0x8 0xa 0x8 0x8 0x5 0x7 0xb 0x8 ,
0x6 0x2 0x8 0x4 0x3 0x5 0x6 0x2 , 0x8 0x1 0x6 0x2 0x6 0x5 0x6 0x5 ,
mid :0x20 0x1f 0x22 0x1d 0x1f 0x20 0x1f 0x25 ,0x23 0x25 0x23 0x21 0x20 0x21 0x26 0x23 ,
0x20 0x1e 0x21 0x20 0x1d 0x21 0x21 0x1e ,0x23 0x1c 0x21 0x1e 0x21 0x21 0x22 0x22 ,
max :0x3b 0x39 0x3b 0x38 0x3a 0x3b 0x39 0x3d ,0x3f 0x41 0x3f 0x3b 0x3c 0x3b 0x41 0x3f ,
0x3b 0x3b 0x3b 0x3c 0x38 0x3d 0x3d 0x3b ,0x3f 0x38 0x3c 0x3a 0x3d 0x3d 0x3f 0x3f ,
range:0x35 0x34 0x32 0x36 0x35 0x35 0x34 0x30 ,0x37 0x37 0x37 0x33 0x37 0x34 0x36 0x37 ,
0x35 0x39 0x33 0x38 0x35 0x38 0x37 0x39 ,0x37 0x37 0x36 0x38 0x37 0x38 0x39 0x3a ,
the write training result:
DQS0:0x64, DQS1:0x5b, DQS2:0x64, DQS3:0x5b,
min :0xa0 0xa0 0xa5 0xa0 0xa0 0xa2 0xa1 0xa9 0xaa ,0x9b 0x9d 0x9e 0x9d 0x9b 0x9c 0x9f 0x9d 0x97 ,
0xa0 0xa0 0xa4 0xa3 0xa1 0xa5 0xa3 0xa3 0xa4 ,0x9e 0x99 0x9c 0x9b 0x9d 0x9c 0x9e 0x9f 0x9d ,
mid :0xbc 0xbc 0xbf 0xbb 0xba 0xbc 0xbc 0xc3 0xc5 ,0xb6 0xb7 0xb7 0xb7 0xb3 0xb4 0xb9 0xb6 0xb1 ,
0xbd 0xbc 0xc1 0xc0 0xbc 0xbf 0xbe 0xbf 0xbf ,0xb9 0xb4 0xb6 0xb6 0xb8 0xb6 0xb9 0xba 0xb8 ,
max :0xd8 0xd8 0xda 0xd6 0xd5 0xd7 0xd8 0xdd 0xe0 ,0xd2 0xd1 0xd0 0xd1 0xcc 0xcd 0xd3 0xcf 0xcc ,
0xdb 0xd8 0xde 0xdd 0xd7 0xda 0xda 0xdb 0xdb ,0xd5 0xd0 0xd1 0xd1 0xd3 0xd1 0xd4 0xd5 0xd3 ,
range:0x38 0x38 0x35 0x36 0x35 0x35 0x37 0x34 0x36 ,0x37 0x34 0x32 0x34 0x31 0x31 0x34 0x32 0x35 ,
0x3b 0x38 0x3a 0x3a 0x36 0x35 0x37 0x38 0x37 ,0x37 0x37 0x35 0x36 0x36 0x35 0x36 0x36 0x36 ,
cs 1:
the read training result:
DQS0:0x38, DQS1:0x36, DQS2:0x33, DQS3:0x34,
min : 0x6 0x4 0x8 0x1 0x5 0x6 0x5 0xc , 0xa 0xa 0x8 0x6 0x5 0x5 0xa 0x8 ,
0x6 0x3 0x7 0x4 0x2 0x4 0x5 0x0 , 0x8 0x1 0x5 0x3 0x6 0x4 0x8 0x8 ,
mid :0x22 0x1f 0x22 0x1e 0x21 0x22 0x21 0x26 ,0x25 0x26 0x25 0x22 0x21 0x21 0x27 0x25 ,
0x20 0x1f 0x21 0x20 0x1d 0x20 0x21 0x1d ,0x23 0x1c 0x20 0x1e 0x21 0x20 0x22 0x23 ,
max :0x3e 0x3b 0x3d 0x3b 0x3d 0x3e 0x3d 0x40 ,0x41 0x43 0x42 0x3e 0x3d 0x3d 0x44 0x42 ,
0x3b 0x3b 0x3b 0x3d 0x38 0x3d 0x3d 0x3b ,0x3f 0x38 0x3b 0x3a 0x3d 0x3c 0x3d 0x3f ,
range:0x38 0x37 0x35 0x3a 0x38 0x38 0x38 0x34 ,0x37 0x39 0x3a 0x38 0x38 0x38 0x3a 0x3a ,
0x35 0x38 0x34 0x39 0x36 0x39 0x38 0x3b ,0x37 0x37 0x36 0x37 0x37 0x38 0x35 0x37 ,
the write training result:
DQS0:0x64, DQS1:0x5b, DQS2:0x64, DQS3:0x5b,
min :0xa1 0xa3 0xa6 0xa1 0xa2 0xa4 0xa3 0xaa 0xac ,0x97 0x99 0x9c 0x99 0x97 0x98 0x9c 0x99 0x93 ,
0xa0 0xa0 0xa3 0xa3 0xa0 0xa3 0xa2 0xa1 0xa2 ,0x9a 0x97 0x99 0x97 0x9a 0x99 0x9c 0x9c 0x99 ,
mid :0xbe 0xbe 0xc1 0xbc 0xbd 0xbf 0xbf 0xc5 0xc7 ,0xb3 0xb4 0xb5 0xb4 0xb1 0xb2 0xb7 0xb3 0xaf ,
0xbc 0xbb 0xbf 0xbf 0xba 0xbd 0xbd 0xbc 0xbd ,0xb5 0xb2 0xb3 0xb1 0xb4 0xb3 0xb6 0xb6 0xb3 ,
max :0xdb 0xd9 0xdd 0xd8 0xd8 0xda 0xdb 0xe0 0xe2 ,0xd0 0xd0 0xce 0xd0 0xcc 0xcc 0xd2 0xce 0xcb ,
0xd9 0xd6 0xdc 0xdb 0xd4 0xd8 0xd8 0xd8 0xd8 ,0xd1 0xcd 0xce 0xcc 0xce 0xce 0xd1 0xd1 0xce ,
range:0x3a 0x36 0x37 0x37 0x36 0x36 0x38 0x36 0x36 ,0x39 0x37 0x32 0x37 0x35 0x34 0x36 0x35 0x38 ,
0x39 0x36 0x39 0x38 0x34 0x35 0x36 0x37 0x36 ,0x37 0x36 0x35 0x35 0x34 0x35 0x35 0x35 0x35 ,
CA Training result:
cs:0 min :0x3e 0x2f 0x3a 0x28 0x37 0x28 0x3c ,0x4d 0x32 0x40 0x2f 0x3c 0x25 0x40 ,
cs:0 mid :0x72 0x71 0x6f 0x6b 0x6b 0x6b 0x64 ,0x83 0x75 0x76 0x6f 0x70 0x68 0x68 ,
cs:0 max :0xa7 0xb3 0xa4 0xae 0xa0 0xae 0x8c ,0xba 0xb8 0xac 0xb0 0xa5 0xac 0x91 ,
cs:0 range:0x69 0x84 0x6a 0x86 0x69 0x86 0x50 ,0x6d 0x86 0x6c 0x81 0x69 0x87 0x51 ,
cs:1 min :0x40 0x34 0x3c 0x2c 0x3a 0x2d 0x35 ,0x4a 0x32 0x41 0x2d 0x3e 0x26 0x36 ,
cs:1 mid :0x76 0x76 0x72 0x6f 0x6f 0x6e 0x6c ,0x81 0x75 0x77 0x6e 0x72 0x69 0x6a ,
cs:1 max :0xac 0xb8 0xa9 0xb2 0xa4 0xaf 0xa4 ,0xb8 0xb8 0xae 0xb0 0xa6 0xac 0x9e ,
cs:1 range:0x6c 0x84 0x6d 0x86 0x6a 0x82 0x6f ,0x6e 0x86 0x6d 0x83 0x68 0x86 0x68 ,
out
U-Boot SPL board init
U-Boot SPL 2017.09-g5961c0c398 #huangjf (Nov 23 2021 - 18:03:16)
unknown raw ID phN
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
MMC error: The cmd index is 1, ret is -110
Card did not respond to voltage select!
mmc_init: -95, time 10
spl: mmc init failed with error: -95
Trying to boot from MMC1
SPL: A/B-slot: _a, successful: 0, tries-remain: 7
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(fe4f274c06...) + OK
## Checking uboot 0x00a00000 ... sha256(0f5b5303fd...) + OK
## Checking fdt 0x00b22630 ... sha256(30938731de...) + OK
## Checking atf-2 0x00068000 ... sha256(8d44036095...) + OK
## Checking atf-3 0xfdcd0000 ... sha256(e410275b51...) + OK
## Checking atf-4 0xfdcc9000 ... sha256(990c53fc01...) + OK
## Checking atf-5 0x00066000 ... sha256(315a4195a9...) + OK
## Checking optee 0x08400000 ... sha256(5a22c90dfc...) + OK
Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00040000)
Total: 233.378 ms
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-181-gc9a647cae:cl
NOTICE: BL31: Built : 10:55:41, Oct 18 2021
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: pmu v1 is valid
INFO: dfs DDR fsp_param[0].freq_mhz= 1560MHz
INFO: dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO: dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO: dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO: Using opteed sec cpu_context!
INFO: boot cpu mask: 0
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
I/TC:
I/TC: OP-TEE version: 3.13.0-515-g7b4275734 #hisping.lin (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05)) #1 Wed Aug 4 07:11:39 UTC 2021 aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0xa00000
INFO: SPSR = 0x3c9
U-Boot 2017.09-g5961c0c398 #huangjf (Nov 23 2021 - 18:03:16 +0800)
Model: Firefly RK3568 Board
PreSerial: 2, raw, 0xfe660000
DRAM: 7.7 GiB
Sysmem: init
Relocation Offset: ed356000
Relocation fdt: eb9f8310 - eb9fece0
CR: M/C/I
Using default environment
dwmmc@fe2b0000: 1, dwmmc@fe2c0000: 2, sdhci@fe310000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
boot mode: recovery (misc)
FIT: no signed, no conf required
DTB: rk-kernel.dtb
HASH(c): OK
I2c0 speed: 100000Hz
PMIC: RK8090 (on=0x10, off=0x00)
vdd_logic init 900000 uV
vdd_gpu init 900000 uV
vdd_npu init 900000 uV
io-domain: OK
Could not find baseparameter partition
Model: Firefly RK3568-ROC-PC HDMI (Linux)
Rockchip UBOOT DRM driver version: v1.0.1
VOP have 1 active VP
vp0 have layer nr:6[0 2 4 1 3 5 ], primary plane: 4
vp1 have layer nr:0[], primary plane: 0
vp2 have layer nr:0[], primary plane: 0
hdmi@fe0a0000 disconnected
CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
apll 816000 KHz
dpll 780000 KHz
gpll 1188000 KHz
cpll 1000000 KHz
npll 1200000 KHz
vpll 24000 KHz
hpll 24000 KHz
ppll 200000 KHz
armclk 816000 KHz
aclk_bus 150000 KHz
pclk_bus 100000 KHz
aclk_top_high 500000 KHz
aclk_top_low 400000 KHz
hclk_top 150000 KHz
pclk_top 100000 KHz
aclk_perimid 300000 KHz
hclk_perimid 150000 KHz
pclk_pmu 100000 KHz
Net: eth1: ethernet@fe010000, eth0: ethernet@fe2a0000
Hit key to stop autoboot('CTRL+C'): 0
## Booting FIT Image at 0xe991a500 with size 0x01edce00
Fdt Ramdisk skip relocation
## Loading kernel from FIT Image at e991a500 ...
Using 'conf' configuration
optee api revision: 2.0
TEEC: Waring: Could not find security partition
## Verified-boot: 0
Trying 'kernel' kernel subimage
Description: unavailable
Type: Kernel Image
Compression: uncompressed
Data Start: 0xe993b300
Data Size: 25270280 Bytes = 24.1 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x00280000
Entry Point: 0x00280000
Hash algo: sha256
Hash value: 51f321c8dc1db39580086a1c29fcb926c8e1b45745c891cffea1cd02f6a30116
Verifying Hash Integrity ... sha256+ OK
## Loading ramdisk from FIT Image at e991a500 ...
Using 'conf' configuration
Trying 'ramdisk' ramdisk subimage
Description: unavailable
Type: RAMDisk Image
Compression: uncompressed
Data Start: 0xeb154d00
Data Size: 6956263 Bytes = 6.6 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x0a200000
Entry Point: unavailable
Hash algo: sha256
Hash value: 848757f81587ca00f60eeb52788b237c9cde5bb2b94663176b2393ad70038702
Verifying Hash Integrity ... sha256+ OK
Loading ramdisk from 0xeb154d00 to 0x0a200000
## Loading fdt from FIT Image at e991a500 ...
Using 'conf' configuration
Trying 'fdt' fdt subimage
Description: unavailable
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0xe991ad00
Data Size: 132152 Bytes = 129.1 KiB
Architecture: AArch64
Load Address: 0x0a100000
Hash algo: sha256
Hash value: 15d96bbfeb5389385695c4dd4412fe628c144b7bb5b54604b65ad33d04b3e07f
Verifying Hash Integrity ... sha256+ OK
Loading fdt from 0x0a100000 to 0x0a100000
Booting using the fdt blob at 0x0a100000
Loading Kernel Image from 0xe993b300 to 0x00280000 ... OK
kernel loaded at 0x00280000, end = 0x01a99808
'reserved-memory' ramoops@110000: addr=110000 size=f0000
Using Device Tree in place at 000000000a100000, end 000000000a123437
vp0, plane_mask:0x3f, primary-id:4, curser-id:-1
vp1, plane_mask:0x0, primary-id:0, curser-id:-1
vp2, plane_mask:0x0, primary-id:0, curser-id:-1
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x100000000 - 0x200000000 (size: 0x100000000)
Total: 858.250 ms
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[ 0.000000] Linux version 4.19.206 (huangjf@tchip16) ((HEAD: 95ba5fb33c06dd47252ffb104f58c3c22bb0f910) (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05), GNU ld (Linaro_Binutils-2017.05) 2.27.0.20161019) #1 SMP Tue Nov 23 11:21:25 CST 2021
[ 0.000000] Machine model: Firefly RK3568-ROC-PC HDMI (Linux)
[ 0.000000] earlycon: uart8250 at MMIO32 0x00000000fe660000 (options '')
[ 0.000000] bootconsole [uart8250] enabled
[ 0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'drm-cubic-lut@00000000': base 0x0000000000000000, size 0 MiB
[ 0.000000] cma: Reserved 16 MiB at 0x00000000ef000000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] psci: SMC Calling Convention v1.2
[ 0.000000] percpu: Embedded 24 pages/cpu s60136 r8192 d29976 u98304
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: Virtualization Host Extensions
[ 0.000000] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1995336
[ 0.000000] Kernel command line: storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal storagenode=sdhci@fe310000 ro rootwait earlycon=uart8250,mmio32,0xfe660000 console=ttyFIQ0 root=PARTLABEL=rootfs rootfstype=ext4 overlayroot=device:dev=PARTLABEL=userdata,fstype=ext4,mkfs=1 coherent_pool=1m systemd.gpt_auto=0 cgroup_enable=memory swapaccount=1
[ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: mapped [mem 0xe9f00000-0xedf00000] (64MB)
[ 0.000000] Memory: 7847052K/8108032K available (15486K kernel code, 2086K rwdata, 5376K rodata, 1664K init, 600K bss, 244596K reserved, 16384K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 56059 entries in 219 pages
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] GICv3: no VLPI support, no direct LPI support
[ 0.000000] ITS [mem 0xfd440000-0xfd45ffff]
[ 0.000000] ITS@0x00000000fd440000: allocated 8192 Devices @ee810000 (indirect, esz 8, psz 64K, shr 0)
[ 0.000000] ITS@0x00000000fd440000: allocated 32768 Interrupt Collections @ee820000 (flat, esz 2, psz 64K, shr 0)
[ 0.000000] ITS: using cache flushing for cmd queue
[ 0.000000] GIC: using LPI property table @0x00000000ee830000
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fd460000
[ 0.000000] CPU0: using LPI pending table @0x00000000ee840000
[ 0.000000] GIC: using cache flushing for LPI property table
[ 0.000000] random: random: get_random_bytes called from start_kernel+0x36c/0x514 with crng_init=0
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.002265] Console: colour dummy device 80x25
[ 0.002727] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[ 0.003681] pid_max: default: 32768 minimum: 301
[ 0.004269] Security Framework initialized
[ 0.004654] AppArmor: AppArmor disabled by boot time parameter
[ 0.005286] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.005996] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.008645] ASID allocator initialised with 32768 entries
[ 0.009363] rcu: Hierarchical SRCU implementation.
[ 0.012857] Platform MSI: interrupt-controller@fd440000 domain created
[ 0.014017] PCI/MSI: /interrupt-controller@fd400000/interrupt-controller@fd440000 domain created
[ 0.015640] smp: Bringing up secondary CPUs ...
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boot
[ 0.017645] Detected VIPT I-cache on CPU1
[ 0.017688] GICv3: CPU1: found redistributor 100 region 0:0x00000000fd480000
[ 0.017742] CPU1: using LPI pending table @0x00000000ee850000
[ 0.017799] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[ 0.019420] Detected VIPT I-cache on CPU2
[ 0.019456] GICv3: CPU2: found redistributor 200 region 0:0x00000000fd4a0000
[ 0.019513] CPU2: using LPI pending table @0x00000000ee860000
[ 0.019559] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[ 0.021137] Detected VIPT I-cache on CPU3
[ 0.021169] GICv3: CPU3: found redistributor 300 region 0:0x00000000fd4c0000
[ 0.021223] CPU3: using LPI pending table @0x00000000ee870000
[ 0.021267] CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
[ 0.021407] smp: Brought up 1 node, 4 CPUs
[ 0.028321] SMP: Total of 4 processors activated.
[ 0.028766] CPU features: detected: GIC system register CPU interface
[ 0.029364] CPU features: detected: Privileged Access Never
[ 0.029880] CPU features: detected: LSE atomic instructions
[ 0.030418] CPU features: detected: User Access Override
[ 0.030912] CPU features: detected: 32-bit EL0 Support
[ 0.031391] CPU features: detected: RAS Extension Support
[ 0.032089] CPU: All CPU(s) started at EL2
[ 0.032495] alternatives: patching kernel code
[ 0.042370] devtmpfs: initialized
[ 0.071752] Registered cp15_barrier emulation handler
[ 0.072244] Registered setend emulation handler
[ 0.073079] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 0.074001] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.075467] pinctrl core: initialized pinctrl subsystem
[ 0.077189] NET: Registered protocol family 16
[ 0.078776] audit: initializing netlink subsys (disabled)
[ 0.079588] audit: type=2000 audit(0.069:1): state=initialized audit_enabled=0 res=1
[ 0.083626] cpuidle: using governor menu
[ 0.084037] Registered FIQ tty driver
[ 0.085331] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.087539] DMA: preallocated 1024 KiB pool for atomic allocations
[ 0.092277] console [pstore-1] enabled
[ 0.092633] pstore: Registered ramoops as persistent store backend
[ 0.093245] ramoops: attached 0xf0000@0x110000, ecc: 0/0
[ 0.134566] rockchip-gpio fdd60000.gpio: probed gpio0 (fdd60000.gpio)
[ 0.135867] rockchip-gpio fe740000.gpio: probed gpio1 (fe740000.gpio)
[ 0.137186] rockchip-gpio fe750000.gpio: probed gpio2 (fe750000.gpio)
[ 0.138468] rockchip-gpio fe760000.gpio: probed gpio3 (fe760000.gpio)
[ 0.139763] rockchip-gpio fe770000.gpio: probed gpio4 (fe770000.gpio)
[ 0.140503] rockchip-pinctrl pinctrl: probed pinctrl
[ 0.159576] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.160483] cryptd: max_cpu_qlen set to 1000
[[ 0.162813] console [ttyFIQ0] enabled
0.162813] console [ttyFIQ0] enabled
[ 0.163524] bootconsole [uart8250] disabled
[ 0.163524] bootconsole [uart8250] disabled
[ 0.164198] Registered fiq debugger ttyFIQ0
[ 0.165339] vcc3v3_sys: supplied by dc_12v
[ 0.165851] vcc5v0_sys: supplied by dc_12v
[ 0.167684] vcc2v5-sys: supplied by vcc3v3_sys
[ 0.168185] pcie30_avdd0v9: supplied by vcc3v3_sys
[ 0.168704] pcie30_avdd1v8: supplied by vcc3v3_sys
[ 0.169218] vcc3v3_bu: supplied by vcc5v0_sys
[ 0.173227] rk_iommu fde4b000.iommu: version = 2
[ 0.174043] rk_iommu fdea0800.iommu: version = 2
[ 0.174582] rk_iommu fded0480.iommu: version = 2
[ 0.174978] rk_iommu fdee0800.iommu: version = 2
[ 0.175350] rk_iommu fdef0800.iommu: version = 2
[ 0.175719] rk_iommu fdf40f00.iommu: version = 2
[ 0.176152] rk_iommu fdf80800.iommu: version = 2
[ 0.176538] rk_iommu fdff1a00.iommu: version = 2
[ 0.176880] rk_iommu fe043e00.iommu: version = 2
[ 0.178061] SCSI subsystem initialized
[ 0.178463] usbcore: registered new interface driver usbfs
[ 0.178551] usbcore: registered new interface driver hub
[ 0.178637] usbcore: registered new device driver usb
[ 0.178770] media: Linux media interface: v0.10
[ 0.178838] videodev: Linux video capture interface: v2.00
[ 0.178970] pps_core: LinuxPPS API ver. 1 registered
[ 0.178996] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.179045] PTP clock support registered
[ 0.179475] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0
[ 0.182689] Advanced Linux Sound Architecture Driver Initialized.
[ 0.183402] Bluetooth: Core ver 2.22
[ 0.183510] NET: Registered protocol family 31
[ 0.183537] Bluetooth: HCI device and connection manager initialized
[ 0.183567] Bluetooth: HCI socket layer initialized
[ 0.183595] Bluetooth: L2CAP socket layer initialized
[ 0.183661] Bluetooth: SCO socket layer initialized
[ 0.184235] rockchip-cpuinfo cpuinfo: SoC : 35681000
[ 0.184267] rockchip-cpuinfo cpuinfo: Serial : 9dbb06aaa3cf6fde
[ 0.185829] clocksource: Switched to clocksource arch_sys_counter
[ 0.297588] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[ 0.298063] NET: Registered protocol family 2
[ 0.298628] IP idents hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.302788] tcp_listen_portaddr_hash hash table entries: 4096 (order: 5, 163840 bytes)
[ 0.303002] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.303624] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes)
[ 0.305637] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.305892] UDP hash table entries: 4096 (order: 6, 393216 bytes)
[ 0.306289] UDP-Lite hash table entries: 4096 (order: 6, 393216 bytes)
[ 0.306876] NET: Registered protocol family 1
[ 0.307584] RPC: Registered named UNIX socket transport module.
[ 0.307612] RPC: Registered udp transport module.
[ 0.307633] RPC: Registered tcp transport module.
[ 0.307652] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.309651] Trying to unpack rootfs image as initramfs...
[ 0.709879] Freeing initrd memory: 6792K
[ 0.711688] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 0.712616] kvm [1]: 16-bit VMID
[ 0.712661] kvm [1]: GICv3: no GICV resource entry
[ 0.712674] kvm [1]: disabling GICv2 emulation
[ 0.712686] kvm [1]: GIC system register CPU interface enabled
[ 0.712875] kvm [1]: vgic interrupt IRQ1
[ 0.713091] kvm [1]: VHE mode initialized successfully
[ 0.715595] Initialise system trusted keyrings
[ 0.715884] workingset: timestamp_bits=45 max_order=21 bucket_order=0
[ 0.725806] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.726987] NFS: Registering the id_resolver key type
[ 0.727041] Key type id_resolver registered
[ 0.727057] Key type id_legacy registered
[ 0.727109] jffs2: version 2.2. (NAND) 漏 2001-2006 Red Hat, Inc.
[ 0.727432] fuse init (API version 7.27)
[ 0.728047] SGI XFS with security attributes, no debug enabled
[ 0.732124] NET: Registered protocol family 38
[ 0.732180] Key type asymmetric registered
[ 0.732196] Asymmetric key parser 'x509' registered
[ 0.732256] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[ 0.732472] io scheduler noop registered
[ 0.732535] io scheduler deadline registered
[ 0.732742] io scheduler cfq registered (default)
[ 0.732772] io scheduler mq-deadline registered
[ 0.732795] io scheduler kyber registered
[ 0.734287] rockchip-csi2-dphy csi2-dphy0: csi2 dphy0 probe successfully!
[ 0.734506] rockchip-csi2-dphy-hw fe870000.csi2-dphy-hw: csi2 dphy hw probe successfully!
[ 0.738219] phy phy-fe8b0000.usb2-phy.0: Linked as a consumer to regulator.4
[ 0.738474] phy phy-fe8b0000.usb2-phy.1: Linked as a consumer to regulator.4
[ 0.738652] phy phy-fe8b0000.usb2-phy.1: No vbus specified for otg port
[ 0.749751] rk-pcie 3c0800000.pcie: Linked as a consumer to regulator.15
[ 0.750352] rochchip_p3phy_init: lock failed 0x6890000, check input refclk and power supply
[ 0.750390] phy phy-fe8c0000.phy.5: phy init failed --> -110
[ 0.750415] rk-pcie 3c0800000.pcie: fail to init phy, err -110
[ 0.750431] mpp_service mpp-srv: d47e486b19bd author: Yandong Lin 2021-11-04 video: rockchip: mpp: use dma-buf-cache func
[ 0.750439] mpp_service mpp-srv: probe start
[ 0.750457] rk-pcie 3c0800000.pcie: phy init failed
[ 0.751697] iommu: Adding device fdf40000.rkvenc to group 5
[ 0.751753] mpp_rkvenc fdf40000.rkvenc: Linked as a consumer to fdf40f00.iommu
[ 0.752026] mpp_rkvenc fdf40000.rkvenc: probing start
[ 0.752669] mpp_rkvenc fdf40000.rkvenc: venc regulator not ready, retry
[ 0.752700] rkvenc_init:1199: failed to add venc devfreq
[ 0.753146] mpp_rkvenc fdf40000.rkvenc: probing finish
[ 0.754704] iommu: Adding device fdea0400.vdpu to group 1
[ 0.754760] mpp_vdpu2 fdea0400.vdpu: Linked as a consumer to fdea0800.iommu
[ 0.755003] mpp_vdpu2 fdea0400.vdpu: probe device
[ 0.755799] mpp_vdpu2 fdea0400.vdpu: probing finish
[ 0.756722] iommu: Adding device fdee0000.vepu to group 3
[ 0.756779] mpp_vepu2 fdee0000.vepu: Linked as a consumer to fdee0800.iommu
[ 0.757054] mpp_vepu2 fdee0000.vepu: probe device
[ 0.757835] mpp_vepu2 fdee0000.vepu: probing finish
[ 0.758535] iommu: Adding device fdef0000.iep to group 4
[ 0.758594] mpp-iep2 fdef0000.iep: Linked as a consumer to fdef0800.iommu
[ 0.758808] mpp-iep2 fdef0000.iep: probe device
[ 0.759475] mpp-iep2 fdef0000.iep: allocate roi buffer failed
[ 0.759704] mpp-iep2 fdef0000.iep: probing finish
[ 0.760344] iommu: Adding device fded0000.jpegd to group 2
[ 0.760401] mpp_jpgdec fded0000.jpegd: Linked as a consumer to fded0480.iommu
[ 0.760598] mpp_jpgdec fded0000.jpegd: probe device
[ 0.761329] mpp_jpgdec fded0000.jpegd: probing finish
[ 0.762069] iommu: Adding device fdf80200.rkvdec to group 6
[ 0.762124] mpp_rkvdec2 fdf80200.rkvdec: Linked as a consumer to fdf80800.iommu
[ 0.762437] mpp_rkvdec2 fdf80200.rkvdec: probing start
[ 0.762702] mpp_rkvdec2 fdf80200.rkvdec: 16 task capacity link mode detected
[ 0.763174] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_a is not found!
[ 0.763205] rkvdec2_init:661: No niu aclk reset resource define
[ 0.763234] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_h is not found!
[ 0.763255] rkvdec2_init:664: No niu hclk reset resource define
[ 0.763517] mpp_rkvdec2 fdf80200.rkvdec: sram_start 0x00000000fdcc0000
[ 0.763550] mpp_rkvdec2 fdf80200.rkvdec: rcb_iova 0x0000000010000000
[ 0.763574] mpp_rkvdec2 fdf80200.rkvdec: sram_size 45056
[ 0.763589] mpp_rkvdec2 fdf80200.rkvdec: rcb_size 65536
[ 0.763608] mpp_rkvdec2 fdf80200.rkvdec: min_width 512
[ 0.763697] mpp_rkvdec2 fdf80200.rkvdec: link mode probe finish
[ 0.763802] mpp_rkvdec2 fdf80200.rkvdec: probing finish
[ 0.764264] mpp_service mpp-srv: probe success
[ 0.773246] dma-pl330 fe530000.dmac: Loaded driver for PL330 DMAC-241330
[ 0.773292] dma-pl330 fe530000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 0.776670] dma-pl330 fe550000.dmac: Loaded driver for PL330 DMAC-241330
[ 0.776715] dma-pl330 fe550000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 0.778603] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[ 0.780131] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[ 0.781299] fe670000.serial: ttyS3 at MMIO 0xfe670000 (irq = 66, base_baud = 1500000) is a 16550A
[ 0.782205] fe680000.serial: ttyS4 at MMIO 0xfe680000 (irq = 67, base_baud = 1500000) is a 16550A
[ 0.783176] fe6c0000.serial: ttyS8 at MMIO 0xfe6c0000 (irq = 68, base_baud = 1500000) is a 16550A
[ 0.787040] random: fast init done
[ 0.787392] random: crng init done
[ 0.787829] iommu: Adding device fe040000.vop to group 8
[ 0.787888] rockchip-vop2 fe040000.vop: Linked as a consumer to fe043e00.iommu
[ 0.794656] rockchip-drm display-subsystem: Linked as a consumer to fe040000.vop
[ 0.796531] rockchip-drm display-subsystem: Linked as a consumer to fe0a0000.hdmi
[ 0.799441] rockchip-drm display-subsystem: dmc is disabled
[ 0.799827] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x3f, primary plane phy id: 4
[ 0.799871] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp1 assign plane mask: 0x0, primary plane phy id: -1
[ 0.799907] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x0, primary plane phy id: -1
[ 0.800203] [drm] unsupported AFBC format[3432564e]
[ 0.800292] [drm] failed to init overlay plane Cluster0-win1
[ 0.800389] [drm] failed to init overlay plane Cluster1-win1
[ 0.800552] rockchip-drm display-subsystem: bound fe040000.vop (ops 0xffffff800908b758)
[ 0.800850] dwhdmi-rockchip fe0a0000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[ 0.801656] dwhdmi-rockchip fe0a0000.hdmi: registered DesignWare HDMI I2C bus driver
[ 0.802549] rockchip-drm display-subsystem: bound fe0a0000.hdmi (ops 0xffffff800908f270)
[ 0.802575] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 0.802588] [drm] No driver support for vblank timestamp query.
[ 0.802902] rockchip-drm display-subsystem: connector[HDMI-A-1] can't found any modes
[ 0.803003] rockchip-drm display-subsystem: can't not find any loader display
[ 0.803038] rockchip-drm display-subsystem: failed to show loader logo
[ 0.803090] [drm] Cannot find any crtc or sizes
[ 0.804211] [drm] Initialized rockchip 2.0.0 20140818 for display-subsystem on minor 0
[ 0.811932] mali fde60000.gpu: Kernel DDK version g7p1-01bet0
[ 0.812064] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.812135] mali fde60000.gpu: Device initialization Deferred
[ 0.813165] brd: module loaded
[ 0.823171] loop: module loaded
[ 0.823867] zram: Added device: zram0
[ 0.824055] lkdtm: No crash points registered, enable through debugfs
[ 0.825933] ahci fc800000.sata: forcing port_map 0x0 -> 0x1
[ 0.826018] ahci fc800000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 0.826052] ahci fc800000.sata: flags: ncq sntf pm led clo only pmp fbs pio slum part ccc apst
[ 0.826092] ahci fc800000.sata: port 0 is not capable of FBS
[ 0.827462] scsi host0: ahci
[ 0.827971] ata1: SATA max UDMA/133 mmio [mem 0xfc800000-0xfc800fff] port 0x100 irq 11
[ 0.830638] libphy: Fixed MDIO Bus: probed
[ 0.830715] CAN device driver interface
[ 0.835092] rk_gmac-dwmac fe010000.ethernet: no regulator found
[ 0.835150] rk_gmac-dwmac fe010000.ethernet: clock input or output? (input).
[ 0.835170] rk_gmac-dwmac fe010000.ethernet: TX delay(0x4f).
[ 0.835186] rk_gmac-dwmac fe010000.ethernet: RX delay(0x26).
[ 0.835206] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no).
[ 0.835291] rk_gmac-dwmac fe010000.ethernet: clock input from PHY
[ 0.840330] rk_gmac-dwmac fe010000.ethernet: init for RGMII
[ 0.840671] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ 0.840704] rk_gmac-dwmac fe010000.ethernet: DWMAC4/5
[ 0.840731] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register supported
[ 0.840755] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine supported
[ 0.840777] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported
[ 0.840802] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported
[ 0.840863] rk_gmac-dwmac fe010000.ethernet: TSO supported
[ 0.840879] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 0.840895] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled
[ 0.972537] libphy: stmmac: probed
[ 0.978550] rk_gmac-dwmac fe2a0000.ethernet: no regulator found
[ 0.978602] rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (input).
[ 0.978623] rk_gmac-dwmac fe2a0000.ethernet: TX delay(0x3c).
[ 0.978640] rk_gmac-dwmac fe2a0000.ethernet: RX delay(0x2f).
[ 0.978661] rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no).
[ 0.978741] rk_gmac-dwmac fe2a0000.ethernet: clock input from PHY
[ 0.983782] rk_gmac-dwmac fe2a0000.ethernet: init for RGMII
[ 0.984153] rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ 0.984184] rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5
[ 0.984211] rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register supported
[ 0.984236] rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine supported
[ 0.984258] rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported
[ 0.984279] rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported
[ 0.984344] rk_gmac-dwmac fe2a0000.ethernet: TSO supported
[ 0.984362] rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 0.984378] rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled
[ 1.115866] libphy: stmmac: probed
[ 1.116175] mdio_bus stmmac-0: MDIO device at address 0 is missing.
[ 1.118430] usbcore: registered new interface driver rndis_wlan
[ 1.118535] usbcore: registered new interface driver rtl8150
[ 1.118627] usbcore: registered new interface driver r8152
[ 1.118711] usbcore: registered new interface driver asix
[ 1.118790] usbcore: registered new interface driver ax88179_178a
[ 1.118873] usbcore: registered new interface driver cdc_ether
[ 1.118952] usbcore: registered new interface driver rndis_host
[ 1.119050] usbcore: registered new interface driver cdc_ncm
[ 1.119140] usbcore: registered new interface driver qmi_wwan_q
[ 1.119274] usbcore: registered new interface driver qmi_wwan
[ 1.119341] usbcore: registered new interface driver cdc_mbim
[ 1.121000] dwc3 fcc00000.dwc3: Failed to get clk 'ref': -2
[ 1.122421] dwc3 fd000000.dwc3: Failed to get clk 'ref': -2
[ 1.125618] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.125670] ehci-pci: EHCI PCI platform driver
[ 1.125774] ehci-platform: EHCI generic platform driver
[ 1.128196] ehci-platform fd800000.usb: EHCI Host Controller
[ 1.128487] ehci-platform fd800000.usb: new USB bus registered, assigned bus number 1
[ 1.129114] ehci-platform fd800000.usb: irq 12, io mem 0xfd800000
[ 1.142541] ehci-platform fd800000.usb: USB 2.0 started, EHCI 1.00
[ 1.142594] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.142888] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 1.142922] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.142948] usb usb1: Product: EHCI Host Controller
[ 1.142973] usb usb1: Manufacturer: Linux 4.19.206 ehci_hcd
[ 1.142995] usb usb1: SerialNumber: fd800000.usb
[ 1.143683] hub 1-0:1.0: USB hub found
[ 1.143759] hub 1-0:1.0: 1 port detected
[ 1.146629] ehci-platform fd880000.usb: EHCI Host Controller
[ 1.146907] ehci-platform fd880000.usb: new USB bus registered, assigned bus number 2
[ 1.147411] ehci-platform fd880000.usb: irq 14, io mem 0xfd880000
[ 1.159211] ehci-platform fd880000.usb: USB 2.0 started, EHCI 1.00
[ 1.159539] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 1.159571] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.159596] usb usb2: Product: EHCI Host Controller
[ 1.159622] usb usb2: Manufacturer: Linux 4.19.206 ehci_hcd
[ 1.159643] usb usb2: SerialNumber: fd880000.usb
[ 1.160291] hub 2-0:1.0: USB hub found
[ 1.160366] hub 2-0:1.0: 1 port detected
[ 1.161484] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.161535] ohci-platform: OHCI generic platform driver
[ 1.161879] ohci-platform fd840000.usb: Generic Platform OHCI controller
[ 1.162186] ohci-platform fd840000.usb: new USB bus registered, assigned bus number 3
[ 1.162568] ohci-platform fd840000.usb: irq 13, io mem 0xfd840000
[ 1.223457] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[ 1.223493] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.223509] usb usb3: Product: Generic Platform OHCI controller
[ 1.223524] usb usb3: Manufacturer: Linux 4.19.206 ohci_hcd
[ 1.223538] usb usb3: SerialNumber: fd840000.usb
[ 1.224235] hub 3-0:1.0: USB hub found
[ 1.224313] hub 3-0:1.0: 1 port detected
[ 1.225085] ohci-platform fd8c0000.usb: Generic Platform OHCI controller
[ 1.225373] ohci-platform fd8c0000.usb: new USB bus registered, assigned bus number 4
[ 1.225695] ohci-platform fd8c0000.usb: irq 15, io mem 0xfd8c0000
[ 1.283474] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[ 1.283506] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.283524] usb usb4: Product: Generic Platform OHCI controller
[ 1.283540] usb usb4: Manufacturer: Linux 4.19.206 ohci_hcd
[ 1.283554] usb usb4: SerialNumber: fd8c0000.usb
[ 1.284238] hub 4-0:1.0: USB hub found
[ 1.284314] hub 4-0:1.0: 1 port detected
[ 1.286600] usbcore: registered new interface driver cdc_acm
[ 1.286618] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.286698] usbcore: registered new interface driver cdc_wdm
[ 1.287039] usbcore: registered new interface driver uas
[ 1.287224] usbcore: registered new interface driver usb-storage
[ 1.287374] usbcore: registered new interface driver usbserial_generic
[ 1.287421] usbserial: USB Serial support registered for generic
[ 1.287506] usbcore: registered new interface driver cp210x
[ 1.287559] usbserial: USB Serial support registered for cp210x
[ 1.287691] usbcore: registered new interface driver ftdi_sio
[ 1.287748] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 1.288005] usbcore: registered new interface driver keyspan
[ 1.288062] usbserial: USB Serial support registered for Keyspan - (without firmware)
[ 1.288118] usbserial: USB Serial support registered for Keyspan 1 port adapter
[ 1.288177] usbserial: USB Serial support registered for Keyspan 2 port adapter
[ 1.288233] usbserial: USB Serial support registered for Keyspan 4 port adapter
[ 1.288324] usbcore: registered new interface driver option
[ 1.288379] usbserial: USB Serial support registered for GSM modem (1-port)
[ 1.288730] usbcore: registered new interface driver oti6858
[ 1.288788] usbserial: USB Serial support registered for oti6858
[ 1.288872] usbcore: registered new interface driver pl2303
[ 1.288926] usbserial: USB Serial support registered for pl2303
[ 1.289016] usbcore: registered new interface driver qcserial
[ 1.289074] usbserial: USB Serial support registered for Qualcomm USB modem
[ 1.289227] usbcore: registered new interface driver sierra
[ 1.289287] usbserial: USB Serial support registered for Sierra USB modem
[ 1.291039] usbcore: registered new interface driver usbtouchscreen
[ 1.291117] ============ himax_hx83102_init 1742 jjlook ==========
[ 1.291141] ============ himax_hx83102_probe 1725 jjlook ==========
[ 1.291238] cyttsp5_loader_init: Parade TTSP FW Loader Driver (Built TTDA.03.08.874312) rc=0
[ 1.291259] cyttsp5_device_access_init: Parade TTSP Device Access Driver (Built TTDA.03.08.874312) rc=0
[ 1.291716] .. rk pwm remotectl v2.0 init
[ 1.292090] input: fe6e0030.pwm as /devices/platform/fe6e0030.pwm/input/input0
[ 1.292682] remotectl-pwm fe6e0030.pwm: pwm version is 0x2130000
[ 1.292725] remotectl-pwm fe6e0030.pwm: cannot find PWR IRQ
[ 1.292753] remotectl-pwm fe6e0030.pwm: pwm sip wakeup config error!!
[ 1.292768] remotectl-pwm fe6e0030.pwm: Donot support ATF Wakeup
[ 1.293771] i2c /dev entries driver
[ 1.295532] fan53555-regulator 0-001c: Failed to get chip ID!
[ 1.297176] rk808 0-0020: chip id: 0x8090
[ 1.297254] rk808 0-0020: No cache defaults, reading back from HW
[ 1.321062] rk808 0-0020: source: on=0x10, off=0x00
[ 1.321102] rk808 0-0020: support dcdc3 fb mode:-22, 63
[ 1.321124] rk808 0-0020: support pmic reset mode:0,0
[ 1.327799] rk808-regulator rk808-regulator: there is no dvs0 gpio
[ 1.327867] rk808-regulator rk808-regulator: there is no dvs1 gpio
[ 1.328363] vdd_logic: supplied by vcc3v3_sys
[ 1.329278] vdd_gpu: supplied by vcc3v3_sys
[ 1.329795] vcc_ddr: supplied by vcc3v3_sys
[ 1.330305] vdd_npu: supplied by vcc3v3_sys
[ 1.331180] vcc_1v8: supplied by vcc3v3_sys
[ 1.331653] vdda0v9_image: supplied by vcc3v3_sys
[ 1.332536] vdda_0v9: supplied by vcc3v3_sys
[ 1.333026] vdda0v9_pmu: supplied by vcc3v3_sys
[ 1.333506] vccio_acodec: supplied by vcc3v3_sys
[ 1.334354] vccio_sd: supplied by vcc3v3_sys
[ 1.334851] vcc3v3_pmu: supplied by vcc3v3_sys
[ 1.335690] vcca_1v8: supplied by vcc3v3_sys
[ 1.336213] vcca1v8_pmu: supplied by vcc3v3_sys
[ 1.336708] vcca1v8_image: supplied by vcc3v3_sys
[ 1.337559] vcc_3v3: supplied by vcc3v3_sys
[ 1.338370] vcc3v3_sd: supplied by vcc3v3_sys
[ 1.339037] rk817-battery rk817-battery: Failed to find matching dt id
[ 1.339440] rk817-charger rk817-charger: Failed to find matching dt id
[ 1.342939] input: rk805 pwrkey as /devices/platform/fdd40000.i2c/i2c-0/0-0020/rk805-pwrkey/input/input1
[ 1.343626] rk808-rtc rk808-rtc: device is disabled
[ 1.343675] rk808-rtc: probe of rk808-rtc failed with error -22
[ 1.345205] fusb302 0-0022: Can't get property of role, set role to default DRP
[ 1.348967] fusb302 0-0022: port 0 probe success with role ROLE_MODE_DRP, try_role ROLE_MODE_NONE
[ 1.349226] input: Typec_Headphone as /devices/platform/fdd40000.i2c/i2c-0/0-0022/input/input2
[ 1.351083] pca953x 1-0021: 1-0021 supply vcc not found, using dummy regulator
[ 1.351204] pca953x 1-0021: Linked as a consumer to regulator.0
[ 1.351424] pca953x 1-0021: failed reading register
[ 1.351518] pca953x 1-0021: Dropping the link to regulator.0
[ 1.361189] rtc-hym8563 5-0051: rtc core: registered hym8563 as rtc0
[ 1.362272] rtc-hym8563 5-0051: setting system clock to 2021-12-07 07:45:51 UTC (1638863151)
[ 1.363940] gsensor_mc3230 5-004c: sensor_register_device: gs_mc3230, id = 27
[ 1.363979] i2c i2c-5: sensor_probe: gs_mc3230,00000000e1df7f2b
[ 1.364044] gsensor_mc3230 5-004c: sensor_chip_init:gs_mc3230:devid=0x0,ops=0x000000002d81c8ba
[ 1.392535] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 1.402703] [Gsensor] init_3230_ctl_data 457 : error: -6
[ 1.402736] gsensor_mc3230 5-004c: sensor_initial:fail to init sensor
[ 1.402752] gsensor_mc3230 5-004c: sensor_chip_init:fail to init sensor
[ 1.402767] i2c i2c-5: sensor_probe failed -2
[ 1.402767]
[ 1.405506] iommu: Adding device fdff0000.rkisp to group 7
[ 1.405566] rkisp_hw fdff0000.rkisp: Linked as a consumer to fdff1a00.iommu
[ 1.405864] rkisp_hw fdff0000.rkisp: is_thunderboot: 0
[ 1.405899] rkisp_hw fdff0000.rkisp: max input:0x0@0fps
[ 1.405947] rkisp_hw fdff0000.rkisp: can't request region for resource [mem 0xfdff0000-0xfdffffff]
[ 1.407173] rkisp rkisp-vir0: rkisp driver version: v01.07.00
[ 1.407315] rkisp rkisp-vir0: No memory-region-thunderboot specified
[ 1.407617] rkisp rkisp-vir0: Entity type for entity rkisp-isp-subdev was not initialized!
[ 1.407648] rkisp rkisp-vir0: Entity type for entity rkisp-csi-subdev was not initialized!
[ 1.410388] usbcore: registered new interface driver uvcvideo
[ 1.410419] USB Video Class driver (1.1.1)
[ 1.410817] rockchip-iodomain fdc20000.syscon:io-domains: Linked as a consumer to regulator.26
[ 1.410885] rockchip-iodomain fdc20000.syscon:io-domains: pmuio1(3300000 uV) supplied by vcc3v3_pmu
[ 1.411055] rockchip-iodomain fdc20000.syscon:io-domains: pmuio2(3300000 uV) supplied by vcc3v3_pmu
[ 1.411222] rockchip-iodomain fdc20000.syscon:io-domains: Linked as a consumer to regulator.24
[ 1.411272] rockchip-iodomain fdc20000.syscon:io-domains: vccio1(3300000 uV) supplied by vccio_acodec
[ 1.411482] rockchip-iodomain fdc20000.syscon:io-domains: Linked as a consumer to regulator.25
[ 1.411535] rockchip-iodomain fdc20000.syscon:io-domains: vccio3(3300000 uV) supplied by vccio_sd
[ 1.411693] rockchip-iodomain fdc20000.syscon:io-domains: Linked as a consumer to regulator.20
[ 1.411752] rockchip-iodomain fdc20000.syscon:io-domains: vccio4(1800000 uV) supplied by vcc_1v8
[ 1.411900] rockchip-iodomain fdc20000.syscon:io-domains: Linked as a consumer to regulator.30
[ 1.411959] rockchip-iodomain fdc20000.syscon:io-domains: vccio5(3300000 uV) supplied by vcc_3v3
[ 1.412117] rockchip-iodomain fdc20000.syscon:io-domains: vccio6(1800000 uV) supplied by vcc_1v8
[ 1.412310] rockchip-iodomain fdc20000.syscon:io-domains: vccio7(3300000 uV) supplied by vcc_3v3
[ 1.416944] rockchip-thermal fe710000.tsadc: tsadc is probed successfully!
[ 1.418486] Bluetooth: HCI UART driver ver 2.3
[ 1.418517] Bluetooth: HCI UART protocol H4 registered
[ 1.418539] Bluetooth: HCI UART protocol ATH3K registered
[ 1.418832] Bluetooth: HCI UART protocol Broadcom registered
[ 1.418951] usbcore: registered new interface driver bfusb
[ 1.419064] usbcore: registered new interface driver btusb
[ 1.419525] cpu cpu0: leakage=29
[ 1.419658] cpu cpu0: Failed to get reg
[ 1.421885] sdhci: Secure Digital Host Controller Interface driver
[ 1.421916] sdhci: Copyright(c) Pierre Ossman
[ 1.421937] Synopsys Designware Multimedia Card Interface Driver
[ 1.423484] dwmmc_rockchip fe000000.dwmmc: IDMAC supports 32-bit address mode.
[ 1.423839] dwmmc_rockchip fe000000.dwmmc: Using internal DMA controller.
[ 1.423876] dwmmc_rockchip fe000000.dwmmc: Version ID is 270a
[ 1.423961] dwmmc_rockchip fe000000.dwmmc: DW MMC controller at irq 42,32 bit host data width,256 deep fifo
[ 1.424203] dwmmc_rockchip fe000000.dwmmc: allocated mmc-pwrseq
[ 1.424237] mmc_host mmc3: card is non-removable.
[ 1.541594] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.36
[ 1.541633] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1.541649] usb 1-1: Product: USB2.0 Hub
[ 1.542741] hub 1-1:1.0: USB hub found
[ 1.543160] hub 1-1:1.0: 4 ports detected
[ 1.543180] mmc_host mmc3: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[ 1.556763] dwmmc_rockchip fe2b0000.dwmmc: IDMAC supports 32-bit address mode.
[ 1.556989] dwmmc_rockchip fe2b0000.dwmmc: Using internal DMA controller.
[ 1.557028] dwmmc_rockchip fe2b0000.dwmmc: Version ID is 270a
[ 1.557168] dwmmc_rockchip fe2b0000.dwmmc: DW MMC controller at irq 50,32 bit host data width,256 deep fifo
[ 1.557363] dwmmc_rockchip fe2b0000.dwmmc: Linked as a consumer to regulator.31
[ 1.557524] dwmmc_rockchip fe2b0000.dwmmc: Linked as a consumer to regulator.25
[ 1.569750] mmc_host mmc1: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[ 1.583026] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.585051] mmc0: Unknown controller version (5). You may experience problems.
[ 1.593258] mmc3: queuing unknown CIS tuple 0x80 (2 bytes)
[ 1.595226] mmc3: queuing unknown CIS tuple 0x80 (3 bytes)
[ 1.597376] mmc3: queuing unknown CIS tuple 0x80 (3 bytes)
[ 1.601153] mmc3: queuing unknown CIS tuple 0x80 (7 bytes)
[ 1.605609] mmc3: queuing unknown CIS tuple 0x81 (9 bytes)
[ 1.617020] mmc0: SDHCI controller on fe310000.sdhci [fe310000.sdhci] using ADMA
[ 1.619507] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.620180] usbcore: registered new interface driver usbhid
[ 1.620208] usbhid: USB HID core driver
[ 1.621074] rockchip,bus bus-npu: Linked as a consumer to regulator.16
[ 1.621122] rockchip,bus bus-npu: Failed to get leakage
[ 1.621344] rockchip,bus bus-npu: Failed to get reg
[ 1.621738] rockchip,bus bus-npu: avs=0
[ 1.625446] rockchip-saradc fe720000.saradc: Linked as a consumer to regulator.27
[ 1.626597] rksfc_base v1.1 2016-01-08
[ 1.627646] rksfc fe300000.sfc: rksfc_probe clk rate = 50000000
[ 1.627746] rkflash_dev_init enter
[ 1.627773] sfc nor id: ff ff ff
[ 1.627786] rkflash[1] is invalid
[ 1.627789] rkflash_dev_init enter
[ 1.627816] sfc_nand id: ff ff ff
[ 1.627837] rkflash[2] is invalid
[ 1.629115] usbcore: registered new interface driver snd-usb-audio
[ 1.632914] rk817-codec rk817-codec: DMA mask not set
[ 1.633948] rk817_codec_parse_dt_property: rk809 hp adc effective value of detection 976~1024
[ 1.633998] invalid rk817->hp_det_gpio: -2
[ 1.634020] invalid gpio: -2
[ 1.643215] NET: Registered protocol family 10
[ 1.644911] Segment Routing with IPv6
[ 1.645075] NET: Registered protocol family 17
[ 1.645115] can: controller area network core (rev 20170425 abi 9)
[ 1.645369] NET: Registered protocol family 29
[ 1.645456] can: raw protocol (rev 20170425)
[ 1.645477] can: broadcast manager protocol (rev 20170425 t)
[ 1.645502] can: netlink gateway (rev 20170425) max_hops=1
[ 1.646035] Bluetooth: RFCOMM socket layer initialized
[ 1.646102] Bluetooth: RFCOMM ver 1.11
[ 1.646146] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 1.646178] Bluetooth: HIDP socket layer initialized
[ 1.646293] [BT_RFKILL]: Enter rfkill_rk_init
[ 1.646320] [WLAN_RFKILL]: Enter rfkill_wlan_init
[ 1.647199] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[ 1.647286] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6275s
[ 1.647312] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[ 1.647333] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[ 1.647405] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,host_wake_irq = 124, flags = 0.
[ 1.647435] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[ 1.647456] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[ 1.647478] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 1
[ 1.647498] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[ 1.648414] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 73.
[ 1.648481] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 96.
[ 1.648521] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 97.
[ 1.648550] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 98.
[ 1.648668] [BT_RFKILL]: Request irq for bt wakeup host
[ 1.648813] [BT_RFKILL]: ** disable irq
[ 1.649055] [BT_RFKILL]: bt_default device registered.
[ 1.649380] Key type dns_resolver registered
[ 1.649820] flash vendor_init_thread!
[ 1.649847] flash vendor storage:20170308 ret = -1
[ 1.651508] mmc0: new HS200 MMC card at address 0001
[ 1.652797] mmcblk0: mmc0:0001 SPeMMC 29.0 GiB
[ 1.653588] mmcblk0boot0: mmc0:0001 SPeMMC partition 1 4.00 MiB
[ 1.654394] mmcblk0boot1: mmc0:0001 SPeMMC partition 2 4.00 MiB
[ 1.654432] Loading compiled-in X.509 certificates
[ 1.654694] mmcblk0rpmb: mmc0:0001 SPeMMC partition 3 4.00 MiB, chardev (239:0)
[ 1.655513] pstore: Using compression: deflate
[ 1.657386] rga2: Driver loaded successfully ver:3.2.63318
[ 1.658000] rga2: Module initialized.
[ 1.659460] mmcblk0: p1 p2 p3 p4 p5 p6
[ 1.669489] mmc_host mmc3: Bus speed (slot 0) = 50000000Hz (slot req 100000000Hz, actual 50000000HZ div = 0)
[ 1.681776] dwmmc_rockchip fe000000.dwmmc: Successfully tuned phase to 357
[ 1.696687] mmc3: new ultra high speed SDR104 SDIO card at address 0001
[ 1.721365] phy phy-fe8a0000.usb2-phy.6: Linked as a consumer to regulator.4
[ 1.721794] phy phy-fe8a0000.usb2-phy.7: No vbus specified for otg port
[ 1.724483] mali fde60000.gpu: Kernel DDK version g7p1-01bet0
[ 1.724544] dwc3 fcc00000.dwc3: Failed to get clk 'ref': -2
[ 1.724783] mali fde60000.gpu: Linked as a consumer to regulator.17
[ 1.725043] mali fde60000.gpu: dev_pm_opp_set_regulators: no regulator (shadercores) found: -19
[ 1.725189] mali fde60000.gpu: leakage=9
[ 1.726109] mali fde60000.gpu: avs=0
[ 1.726141] W : [File] : drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] : 112; [Func] : kbase_platform_rk_init(); power-off-delay-ms not available.
[ 1.726683] mali fde60000.gpu: GPU identified as 0x2 arch 7.4.0 r1p0 status 0
[ 1.726839] mali fde60000.gpu: No priority control manager is configured
[ 1.726873] mali fde60000.gpu: No memory group manager is configured
[ 1.727701] mali fde60000.gpu: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0 h_table=0
[ 1.728961] mali fde60000.gpu: Probed as mali0
[ 1.731293] dwc3 fd000000.dwc3: Failed to get clk 'ref': -2
[ 1.735751] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller
[ 1.736253] xhci-hcd xhci-hcd.4.auto: new USB bus registered, assigned bus number 5
[ 1.737215] xhci-hcd xhci-hcd.4.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000011002010010
[ 1.737314] xhci-hcd xhci-hcd.4.auto: irq 82, io mem 0xfd000000
[ 1.737813] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 1.737834] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.737850] usb usb5: Product: xHCI Host Controller
[ 1.737869] usb usb5: Manufacturer: Linux 4.19.206 xhci-hcd
[ 1.737894] usb usb5: SerialNumber: xhci-hcd.4.auto
[ 1.738707] hub 5-0:1.0: USB hub found
[ 1.738786] hub 5-0:1.0: 1 port detected
[ 1.739343] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller
[ 1.739720] xhci-hcd xhci-hcd.4.auto: new USB bus registered, assigned bus number 6
[ 1.739771] xhci-hcd xhci-hcd.4.auto: Host supports USB 3.0 SuperSpeed
[ 1.739904] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.740127] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.19
[ 1.740162] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.740187] usb usb6: Product: xHCI Host Controller
[ 1.740211] usb usb6: Manufacturer: Linux 4.19.206 xhci-hcd
[ 1.740233] usb usb6: SerialNumber: xhci-hcd.4.auto
[ 1.741019] hub 6-0:1.0: USB hub found
[ 1.741103] hub 6-0:1.0: 1 port detected
[ 1.742310] input: adc-keys as /devices/platform/adc-keys/input/input3
[ 1.744676] asoc-simple-card hdmi-sound: i2s-hifi <-> fe400000.i2s mapping ok
[ 1.753379] asoc-simple-card rk809-sound: rk817-hifi <-> fe410000.i2s mapping ok
[ 1.753441] asoc-simple-card rk809-sound: ASoC: no source widget found for MICBIAS1
[ 1.753459] asoc-simple-card rk809-sound: ASoC: Failed to add route MICBIAS1 -> direct -> Mic Jack
[ 1.753475] asoc-simple-card rk809-sound: ASoC: no sink widget found for IN1P
[ 1.753492] asoc-simple-card rk809-sound: ASoC: Failed to add route Mic Jack -> direct -> IN1P
[ 1.753506] asoc-simple-card rk809-sound: ASoC: no source widget found for HPOL
[ 1.753522] asoc-simple-card rk809-sound: ASoC: Failed to add route HPOL -> direct -> Headphone Jack
[ 1.753549] asoc-simple-card rk809-sound: ASoC: no source widget found for HPOR
[ 1.753573] asoc-simple-card rk809-sound: ASoC: Failed to add route HPOR -> direct -> Headphone Jack
[ 1.758191] register spi return v = :0
[ 1.758230] dhd_module_init: in Dongle Host Driver, version 100.10.545.9 (r826445-20200316-8)
[ 1.758255] ======== dhd_wlan_init_plat_data ========
[ 1.758275] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter
[ 1.758370] dhd_wlan_init_gpio: WL_HOST_WAKE=-1, oob_irq=111, oob_irq_flags=0x414
[ 1.758385] dhd_wlan_init_gpio: WL_REG_ON=-1
[ 1.758397] dhd_wifi_platform_load: Enter
[ 1.758423] Power-up adapter 'DHD generic adapter'
[ 1.759564] wifi_platform_set_power = 1, delay: 200 msec
[ 1.759590] ======== PULL WL_REG_ON(-1) HIGH! ========
[ 1.759617] [WLAN_RFKILL]: rockchip_wifi_power: 1
[ 1.759638] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
[ 1.759657] [WLAN_RFKILL]: wifi turn on power [GPIO-1-0]
[ 1.782652] vendor storage:20190527 ret = 0
[ 1.833634] devfreq fde60000.gpu: Couldn't update frequency transition information.
[ 2.065997] wifi_platform_bus_enumerate device present 1
[ 2.066032] ======== Card detection to detect SDIO card! ========
[ 2.066046] mmc3:mmc host rescan start!
[ 2.082286] bcmsdh_register: register client driver
[ 2.082549] bcmsdh_sdmmc_probe: Enter num=1
[ 2.083320] bcmsdh_sdmmc_probe: Enter num=2
[ 2.083338] bus num (host idx)=3, slot num (rca)=1
[ 2.083351] found adapter info 'DHD generic adapter'
[ 2.083453] sdioh_attach: set sd_f2_blocksize 256
[ 2.083653] sdioh_attach: sd clock rate = 0
[ 2.084404] dhdsdio_probe : no mutex held. set lock
[ 2.084882] F1 signature read @0x18000000=0x15294345
[ 2.098468] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x9 pkg:0x2
[ 2.101355] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 2.101640] [dhd] dhd_conf_set_chiprev : chip=0x4345, chiprev=9
[ 2.102932] [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 2.102964] [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 2.102979] [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 2.102993] [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 2.103006] [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 2.103344] dhd_log_dump_init: kernel log buf size = 256KB; logdump_prsrv_tailsize = 80KB; limit prsrv tail size to = 38KB
[ 2.104925] dhd_attach(): thread:dhd_watchdog_thread:6b started
[ 2.105156] dhd_attach(): thread:dhd_dpc:6c started
[ 2.105375] dhd_attach(): thread:dhd_rxf:6d started
[ 2.105410] dhd_deferred_work_init: work queue initialized
[ 2.105431] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 2
[ 2.105572] get_mem_val_from_file: File [/data/misc/wifi/.memdump.info] doesn't exist
[ 2.105607] dhd_get_memdump_info: MEMDUMP ENABLED = 3
[ 2.105638] sdioh_cis_read: func_cis_ptr[0]=0x10ac
[ 2.124268] dhdsdio_probe_init: making DHD_BUS_DOWN
[ 2.124612] Dongle Host Driver, version 100.10.545.9 (r826445-20200316-8)
[ 2.125461] Register interface [wlan0] MAC: 10:2c:6b:c8:41:97
[ 2.125461]
[ 2.125580] dhd_dbg_detach_pkt_monitor, 2100
[ 2.125603] dhd_bus_devreset: == Power OFF ==
[ 2.126093] dhd_bus_stop: making DHD_BUS_DOWN
[ 2.126174] bcmsdh_oob_intr_unregister: Enter
[ 2.126198] bcmsdh_oob_intr_unregister: irq is not registered
[ 2.126221] dhd_bus_devreset: making dhdpub up FALSE
[ 2.126253] dhd_txglom_enable: enable 0
[ 2.126273] dhd_bus_devreset: making DHD_BUS_DOWN
[ 2.126296] dhd_bus_devreset: WLAN OFF DONE
[ 2.126392] wifi_platform_set_power = 0, delay: 0 msec
[ 2.126424] ======== PULL WL_REG_ON(-1) LOW! ========
[ 2.126447] [WLAN_RFKILL]: rockchip_wifi_power: 0
[ 2.126476] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
[ 2.126499] [WLAN_RFKILL]: wifi shut off power [GPIO-1-1]
[ 2.126522] dhdsdio_probe : the lock is released.
[ 2.127872] dhd_module_init: Exit err=0
[ 2.128463] ==gsl_ts_init==
[ 2.128570] ret=0
[ 2.130148] iommu: Adding device fde40000.npu to group 0
[ 2.130211] RKNPU fde40000.npu: Linked as a consumer to fde4b000.iommu
[ 2.130895] RKNPU fde40000.npu: RKNPU: rknpu iommu is enabled, using iommu mode
[ 2.131128] RKNPU fde40000.npu: Linked as a consumer to regulator.19
[ 2.131178] RKNPU fde40000.npu: can't request region for resource [mem 0xfde40000-0xfde4ffff]
[ 2.132068] [drm] Initialized rknpu 0.4.2 20210701 for fde40000.npu on minor 1
[ 2.132552] RKNPU fde40000.npu: leakage=4
[ 2.133537] RKNPU fde40000.npu: avs=0
[ 2.134292] RKNPU fde40000.npu: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[ 2.134334] RKNPU fde40000.npu: failed to find power_model node
[ 2.134365] RKNPU fde40000.npu: RKNPU: failed to initialize power model
[ 2.134390] RKNPU fde40000.npu: RKNPU: failed to get dynamic-coefficient
[ 2.136421] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 2.143573] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 2.143773] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 2.143803] cfg80211: failed to load regulatory.db
[ 2.145741] rockchip-pm rockchip-suspend: not set pwm-regulator-config
[ 2.148257] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 417; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '11:22:35', on 'Nov 23 2021'.
[ 2.148888] Mali:
[ 2.148892] Mali device driver loaded
[ 2.148941] rkisp rkisp-vir0: clear unready subdev num: 4
[ 2.148967] rockchip-csi2-dphy0: No link between dphy and sensor
[ 2.149878] rockchip-csi2-dphy0: No link between dphy and sensor
[ 2.149907] rkisp-vir0: update sensor failed
v 2.171367]
|
|
