编译好内核下载到板子启动不出来，求大神指导~~~在线等答案

dianziit

可以开机？问题描述的清楚点，不然弄不懂你的问题是什么

小默jiang

dianziit 发表于 2017-4-11 12:16
可以开机？问题描述的清楚点，不然弄不懂你的问题是什么

大神，请教下，目前是 进不了 kernel，kernel是自编译的，不可以开机；log 只打出以下那么多
[16-43-43]U-Boot 2014.10-RK3288-10-gc28aaca-dirty (Jul 10 2017 - 16:11:05)
[16-43-43]
[16-43-43]CPU: rk3288
[16-43-43]cpu version = 0
[16-43-43]CPU's clock information:
[16-43-43]    arm pll = 600000000HZ
[16-43-43]    periph pll = 297000000HZ
[16-43-43]    ddr pll = 200000000HZ
[16-43-43]    codec pll = 384000000HZ
[16-43-43]Board:  Rockchip platform Board
[16-43-43]DRAM:  Found dram banks: 1
[16-43-43]Adding bank:0000000000000000(0000000080000000)
[16-43-43]128 MiB
[16-43-43]GIC CPU mask = 0x00000001
[16-43-43]SdmmcInit = 0 400
[16-43-43]SdmmcInit = 2 0
[16-43-43]storage init OK!
[16-43-43]Using default environment
[16-43-43]
[16-43-43]GetParam
[16-43-43]Load FDT from boot image.
[16-43-43]no key node
[16-43-44]No pmic detect.
[16-43-44]can't find dts node for pwm0
[16-43-44]Can't find dts node for fuel guage cw201x
[16-43-44]SecureBootEn = 0, SecureBootLock = 0
[16-43-44]
[16-43-44]#Boot ver: 2017-07-10#2.30
[16-43-44]empty serial no.
[16-43-44]checkKey
[16-43-44]vbus = 1
[16-43-44]no fuel gauge found
[16-43-44]no fuel gauge found
[16-43-44]read logo on state from dts [0]
[16-43-44]I2C bus error, PLS set i2c bus first!
[16-43-44]I2C bus error, PLS set i2c bus first!
[16-43-44]I2C bus error, PLS set i2c bus first!
[16-43-44]I2C bus error, PLS set i2c bus first!
[16-43-44][jxw] lcd power ldo6,ldo8,swout2 on.
[16-43-44]I2C bus error, PLS set i2c bus first!
[16-43-44]I2C bus error, PLS set i2c bus first!
[16-43-44]no fuel gauge found
[16-43-44]misc partition not found!
[16-43-45]Hit any key to stop autoboot:  0
[16-43-45]boot or recovery image sha mismatch!
[16-43-45]Unable to boot:boot
[16-43-45]try to start recovery


求教下大神，要从哪几个方面入手解决

老牛非老牛

各种问题，根本没法编译。官方又不给个标准编译环境(ubuntu版本)