|
发表于 2022-4-21 17:39:01
只看该作者
5#
使用固件:ubuntu_18.04_RK3568_ext4_v2.10-42-g50c7f0ac_20211012-0154_MINIMAL.img
报错如下:
启动过程如下:
U-Boot 2017.09(u-boot commit id: 0b07ec816470af0052545233fbdc6f33fc370bf2)(sdk version: rk356x_linux_release_20220311_v1.2.3a.xml)-g0b07ec8164-dirty #dlj (Apr 09 2022 - 20:34:30 +0800)
Model: Rockchip RK3568 Evaluation Board
PreSerial: 2, raw, 0xfe660000
DRAM: 1006 MiB
Sysmem: init
Relocation Offset: 3d34a000
Relocation fdt: 3b9f8908 - 3b9fece8
CR: M/C/I
dwmmc@fe2b0000: 1, dwmmc@fe2c0000: 2, sdhci@fe310000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
DM: v1
boot mode: None
FIT: no signed, no conf required
DTB: rk-kernel.dtb
HASH(c): OK
I2c0 speed: 100000Hz
vsel-gpios- not found! Error: -2
vdd_cpu 825000 uV
PMIC: RK8090 (on=0x10, off=0x00)
vdd_logic init 900000 uV
vdd_gpu init 900000 uV
vdd_npu init 900000 uV
io-domain: OK
Could not find baseparameter partition
Model: Firefly RK3566-ROC-PC HDMI(Linux)
## Error: Can't overwrite "ethaddr"
## Error inserting "ethaddr" variable, errno=1
## Error: Can't overwrite "eth1addr"
## Error inserting "eth1addr" variable, errno=1
## Error: Can't overwrite "serial#"
## Error inserting "serial#" variable, errno=1
Rockchip UBOOT DRM driver version: v1.0.1
VOP have 1 active VP
vp0 have layer nr:6[0 2 4 1 3 5 ], primary plane: 4
vp1 have layer nr:0[], primary plane: 0
vp2 have layer nr:0[], primary plane: 0
hdmi@fe0a0000 disconnected
CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
apll 1416000 KHz
dpll 528000 KHz
gpll 1188000 KHz
cpll 1000000 KHz
npll 1200000 KHz
vpll 24000 KHz
hpll 24000 KHz
ppll 200000 KHz
armclk 1416000 KHz
aclk_bus 150000 KHz
pclk_bus 100000 KHz
aclk_top_high 500000 KHz
aclk_top_low 400000 KHz
hclk_top 150000 KHz
pclk_top 100000 KHz
aclk_perimid 300000 KHz
hclk_perimid 150000 KHz
pclk_pmu 100000 KHz
Net: eth1: ethernet@fe010000
Hit key to stop autoboot('CTRL+C'): 0
ethernet@fe010000 Waiting for PHY auto negotiation to complete. done
Using ethernet@fe010000 device
TFTP from server 192.168.154.134; our IP address is 192.168.154.10
Filename 'boot.img'.
Load address: 0x4080000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#######
1.5 MiB/s
done
Bytes transferred = 33494016 (1ff1400 hex)
BOOTM: transferring to board FIT
DTB: rk-kernel.dtb
HASH(c): OK
## Booting FIT Image at 0x4080000 with size 0x01f93400
## Loading kernel from FIT Image at 04080000 ...
Using 'conf' configuration
optee api revision: 2.0
TEEC: Waring: Could not find security partition
## Verified-boot: 0
Trying 'kernel' kernel subimage
Description: unavailable
Type: Kernel Image
Compression: uncompressed
Data Start: 0x0409f400
Data Size: 24119304 Bytes = 23 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x00280000
Entry Point: 0x00280000
Hash algo: sha256
Hash value: 6dd0c8d639d9b928ed52aad4e52d621e07fcd3b11e8e3f33ee59c73a42ec6949
Verifying Hash Integrity ... sha256+ OK
## Loading ramdisk from FIT Image at 04080000 ...
Using 'conf' configuration
Trying 'ramdisk' ramdisk subimage
Description: unavailable
Type: RAMDisk Image
Compression: uncompressed
Data Start: 0x0579fe00
Data Size: 8860887 Bytes = 8.5 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x0a200000
Entry Point: unavailable
Hash algo: sha256
Hash value: 252b580d48d2afa60baba78b73045c9ccc36e894535d5683b9d1d2f4158db7e1
Verifying Hash Integrity ... sha256+ OK
Loading ramdisk from 0x0579fe00 to 0x0a200000
## Loading fdt from FIT Image at 04080000 ...
Using 'conf' configuration
Trying 'fdt' fdt subimage
Description: unavailable
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x04080800
Data Size: 125540 Bytes = 122.6 KiB
Architecture: AArch64
Load Address: 0x0a100000
Hash algo: sha256
Hash value: c807e745d4b73c290a4e8b4b488ab0fc32aef81d0ec00d1e32bb73cc15c95aa0
Verifying Hash Integrity ... sha256+ OK
Loading fdt from 0x0a100000 to 0x0a100000
Booting using the fdt blob at 0x0a100000
Loading Kernel Image from 0x0409f400 to 0x00280000 ... OK
kernel loaded at 0x00280000, end = 0x01980808
'reserved-memory' abc@80900000: addr=80900000 size=100000
'reserved-memory' ramoops@110000: addr=110000 size=f0000
Using Device Tree in place at 000000000a100000, end 000000000a121a63
vp0, plane_mask:0x15, primary-id:4, curser-id:-1
vp1, plane_mask:0x0, primary-id:0, curser-id:-1
vp2, plane_mask:0x0, primary-id:0, curser-id:-1
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0x40000000 (size: 0x36c00000)
Total: 28703.149 ms
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[ 0.000000] Linux version 4.19.219 (dlj@dlj-virtual-machine) (firefly: 72491ed436765c35dddc56ce27b537a4d3703107) (sdk version: rk356x_linux_release_20220311_v1.2.3a.xml) (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05), GNU ld (Linaro_Binutils-2017.05) 2.27.0.20161019) #2 SMP Mon Apr 18 19:20:31 CST 2022
[ 0.000000] Machine model: Firefly RK3566-ROC-PC HDMI(Linux)
[ 0.000000] earlycon: uart8250 at MMIO32 0x00000000fe660000 (options '')
[ 0.000000] bootconsole [uart8250] enabled
[ 0.000000] cma: Reserved 16 MiB at 0x000000003ec00000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] psci: SMC Calling Convention v1.2
[ 0.000000] percpu: Embedded 23 pages/cpu s54184 r8192 d31832 u94208
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: Virtualization Host Extensions
[ 0.000000] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 253448
[ 0.000000] Kernel command line: root=/dev/nfs rw nfsroot=192.168.154.134:/home/dlj/linux/nfs/rootfs,v3 ip=192.168.154.10:192.168.154.134:192.168.154.1:255.255.255.0::eth0:off storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal storagenode=sdhci@fe310000 rootwait earlycon=uart8250,mmio32,0xfe660000 console=ttyFIQ0 rootfstype=ext4
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 959552K/1030144K available (14718K kernel code, 1986K rwdata, 5220K rodata, 1600K init, 586K bss, 54208K reserved, 16384K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 53242 entries in 208 pages
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] GICv3: no VLPI support, no direct LPI support
[ 0.000000] ITS [mem 0xfd440000-0xfd45ffff]
[ 0.000000] ITS@0x00000000fd440000: allocated 8192 Devices @3e500000 (indirect, esz 8, psz 64K, shr 0)
[ 0.000000] ITS@0x00000000fd440000: allocated 32768 Interrupt Collections @3e510000 (flat, esz 2, psz 64K, shr 0)
[ 0.000000] ITS: using cache flushing for cmd queue
[ 0.000000] GIC: using LPI property table @0x000000003e520000
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fd460000
[ 0.000000] CPU0: using LPI pending table @0x000000003e530000
[ 0.000000] GIC: using cache flushing for LPI property table
[ 0.000000] random: random: get_random_bytes called from start_kernel+0x36c/0x510 with crng_init=0
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000004] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.001801] Console: colour dummy device 80x25
[ 0.002248] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[ 0.003206] pid_max: default: 32768 minimum: 301
[ 0.003763] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.004393] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.006336] ASID allocator initialised with 32768 entries
[ 0.006954] rcu: Hierarchical SRCU implementation.
[ 0.009603] Platform MSI: interrupt-controller@fd440000 domain created
[ 0.010598] PCI/MSI: /interrupt-controller@fd400000/interrupt-controller@fd440000 domain created
[ 0.012049] smp: Bringing up secondary CPUs ...
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boot
[ 0.013724] Detected VIPT I-cache on CPU1
[ 0.013756] GICv3: CPU1: found redistributor 100 region 0:0x00000000fd480000
[ 0.013794] CPU1: using LPI pending table @0x000000003e6b0000
[ 0.013843] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[ 0.015162] Detected VIPT I-cache on CPU2
[ 0.015188] GICv3: CPU2: found redistributor 200 region 0:0x00000000fd4a0000
[ 0.015234] CPU2: using LPI pending table @0x000000003e700000
[ 0.015270] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[ 0.016543] Detected VIPT I-cache on CPU3
[ 0.016566] GICv3: CPU3: found redistributor 300 region 0:0x00000000fd4c0000
[ 0.016610] CPU3: using LPI pending table @0x000000003e720000
[ 0.016645] CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
[ 0.016738] smp: Brought up 1 node, 4 CPUs
[ 0.023643] SMP: Total of 4 processors activated.
[ 0.024084] CPU features: detected: GIC system register CPU interface
[ 0.024681] CPU features: detected: Privileged Access Never
[ 0.025200] CPU features: detected: LSE atomic instructions
[ 0.025717] CPU features: detected: User Access Override
[ 0.026229] CPU features: detected: 32-bit EL0 Support
[ 0.026709] CPU features: detected: RAS Extension Support
[ 0.027340] CPU: All CPU(s) started at EL2
[ 0.027743] alternatives: patching kernel code
[ 0.033317] devtmpfs: initialized
[ 0.051787] Registered cp15_barrier emulation handler
[ 0.052273] Registered setend emulation handler
[ 0.052983] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 0.053900] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.055046] pinctrl core: initialized pinctrl subsystem
[ 0.056412] NET: Registered protocol family 16
[ 0.060170] cpuidle: using governor menu
[ 0.060568] Registered FIQ tty driver
[ 0.061451] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.063353] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.068014] console [pstore-1] enabled
[ 0.068370] pstore: Registered ramoops as persistent store backend
[ 0.068949] ramoops: attached 0xf0000@0x110000, ecc: 0/0
[ 0.094093] rockchip-gpio fdd60000.gpio: probed gpio0 (fdd60000.gpio)
[ 0.095172] rockchip-gpio fe740000.gpio: probed gpio1 (fe740000.gpio)
[ 0.096233] rockchip-gpio fe750000.gpio: probed gpio2 (fe750000.gpio)
[ 0.097337] rockchip-gpio fe760000.gpio: probed gpio3 (fe760000.gpio)
[ 0.098388] rockchip-gpio fe770000.gpio: probed gpio4 (fe770000.gpio)
[ 0.099068] rockchip-pinctrl pinctrl: probed pinctrl
[ 0.110938] cryptd: max_cpu_qlen set to 1000
[[ 0.112797] console [ttyFIQ0] enabled
0.112797] console [ttyFIQ0] enabled
[ 0.113475] bootconsole [ua[ 0.113475] bootconsole [uart8250] disabled
rt8250] disabled
[ 0.114417] Registered fiq debugger ttyFIQ0
[ 0.115233] vcc3v3_sys: supplied by dc_12v
[ 0.115558] vcc5v0_sys: supplied by dc_12v
[ 0.116760] vcc2v5-sys: supplied by vcc3v3_sys
[ 0.117098] vcc3v3_vga: supplied by vcc3v3_sys
[ 0.117419] pcie30_avdd0v9: supplied by vcc3v3_sys
[ 0.117733] pcie30_avdd1v8: supplied by vcc3v3_sys
[ 0.118064] vcc3v3_bu: supplied by vcc5v0_sys
[ 0.119432] rk_iommu fde4b000.iommu: version = 2
[ 0.119922] rk_iommu fdea0800.iommu: version = 2
[ 0.120262] rk_iommu fded0480.iommu: version = 2
[ 0.120639] rk_iommu fdee0800.iommu: version = 2
[ 0.120972] rk_iommu fdef0800.iommu: version = 2
[ 0.121271] rk_iommu fdf40f00.iommu: version = 2
[ 0.121642] rk_iommu fdf80800.iommu: version = 2
[ 0.121972] rk_iommu fdff1a00.iommu: version = 2
[ 0.122275] rk_iommu fe043e00.iommu: version = 2
[ 0.123083] SCSI subsystem initialized
[ 0.123311] usbcore: registered new interface driver usbfs
[ 0.123377] usbcore: registered new interface driver hub
[ 0.123431] usbcore: registered new device driver usb
[ 0.123512] media: Linux media interface: v0.10
[ 0.123554] videodev: Linux video capture interface: v2.00
[ 0.123638] pps_core: LinuxPPS API ver. 1 registered
[ 0.123655] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.123682] PTP clock support registered
[ 0.123977] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0
[ 0.126104] Advanced Linux Sound Architecture Driver Initialized.
[ 0.126537] Bluetooth: Core ver 2.22
[ 0.126583] NET: Registered protocol family 31
[ 0.126599] Bluetooth: HCI device and connection manager initialized
[ 0.126620] Bluetooth: HCI socket layer initialized
[ 0.126637] Bluetooth: L2CAP socket layer initialized
[ 0.126675] Bluetooth: SCO socket layer initialized
[ 0.127105] rockchip-cpuinfo cpuinfo: SoC : 35662000
[ 0.127117] rockchip-cpuinfo cpuinfo: Serial : 058148cbc6cefd99
[ 0.128090] clocksource: Switched to clocksource arch_sys_counter
[ 0.199939] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[ 0.200270] NET: Registered protocol family 2
[ 0.200417] IP idents hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.201140] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 20480 bytes)
[ 0.201183] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.201265] TCP bind hash table entries: 8192 (order: 6, 262144 bytes)
[ 0.201533] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.201685] UDP hash table entries: 512 (order: 3, 49152 bytes)
[ 0.201751] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes)
[ 0.201967] NET: Registered protocol family 1
[ 0.202542] RPC: Registered named UNIX socket transport module.
[ 0.202561] RPC: Registered udp transport module.
[ 0.202574] RPC: Registered tcp transport module.
[ 0.202587] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.203903] Trying to unpack rootfs image as initramfs...
[ 0.513893] Freeing initrd memory: 8652K
[ 0.515213] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 0.517224] Initialise system trusted keyrings
[ 0.517436] workingset: timestamp_bits=61 max_order=18 bucket_order=0
[ 0.523170] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.523933] NFS: Registering the id_resolver key type
[ 0.523974] Key type id_resolver registered
[ 0.523984] Key type id_legacy registered
[ 0.524017] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.524203] fuse init (API version 7.27)
[ 0.524635] SGI XFS with security attributes, no debug enabled
[ 0.527066] NET: Registered protocol family 38
[ 0.527104] Key type asymmetric registered
[ 0.527114] Asymmetric key parser 'x509' registered
[ 0.527155] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[ 0.527174] io scheduler noop registered
[ 0.527188] io scheduler deadline registered
[ 0.527301] io scheduler cfq registered (default)
[ 0.527319] io scheduler mq-deadline registered
[ 0.527333] io scheduler kyber registered
[ 0.528372] rockchip-csi2-dphy csi2-dphy0: csi2 dphy0 probe successfully!
[ 0.528530] rockchip-csi2-dphy-hw fe870000.csi2-dphy-hw: csi2 dphy hw probe successfully!
[ 0.530441] phy phy-fe8a0000.usb2-phy.0: Linked as a consumer to regulator.4
[ 0.530661] phy phy-fe8a0000.usb2-phy.1: No vbus specified for otg port
[ 0.531910] extcon extcon1: failed to create extcon usb2-phy link
[ 0.532046] phy phy-fe8b0000.usb2-phy.2: Linked as a consumer to regulator.4
[ 0.532200] phy phy-fe8b0000.usb2-phy.3: Linked as a consumer to regulator.4
[ 0.532314] phy phy-fe8b0000.usb2-phy.3: No vbus specified for otg port
[ 0.539348] rk-pcie 3c0000000.pcie: Linked as a consumer to regulator.12
[ 0.539609] rk-pcie 3c0000000.pcie: missing legacy IRQ resource
[ 0.539639] rk-pcie 3c0000000.pcie: Missing *config* reg space
[ 0.539666] rk-pcie 3c0000000.pcie: host bridge /pcie@fe260000 ranges:
[ 0.539696] rk-pcie 3c0000000.pcie: err 0x300000000..0x3007fffff -> 0x00000000
[ 0.539722] rk-pcie 3c0000000.pcie: IO 0x300800000..0x3008fffff -> 0x00800000
[ 0.539746] rk-pcie 3c0000000.pcie: MEM 0x300900000..0x33fffffff -> 0x00900000
[ 0.539804] mpp_service mpp-srv: be32fafb08b3 author: Yandong Lin 2021-11-18 video: rockchip: mpp: Fix mpp_iommu_refresh crash issue
[ 0.539826] mpp_service mpp-srv: probe start
[ 0.540641] iommu: Adding device fdf40000.rkvenc to group 5
[ 0.540669] mpp_rkvenc fdf40000.rkvenc: Linked as a consumer to fdf40f00.iommu
[ 0.540874] mpp_rkvenc fdf40000.rkvenc: probing start
[ 0.541319] mpp_rkvenc fdf40000.rkvenc: venc regulator not ready, retry
[ 0.541338] rkvenc_init:1199: failed to add venc devfreq
[ 0.541696] mpp_rkvenc fdf40000.rkvenc: probing finish
[ 0.542740] iommu: Adding device fdea0400.vdpu to group 1
[ 0.542778] mpp_vdpu2 fdea0400.vdpu: Linked as a consumer to fdea0800.iommu
[ 0.542955] mpp_vdpu2 fdea0400.vdpu: probe device
[ 0.543499] mpp_vdpu2 fdea0400.vdpu: probing finish
[ 0.543998] iommu: Adding device fdee0000.vepu to group 3
[ 0.544034] mpp_vepu2 fdee0000.vepu: Linked as a consumer to fdee0800.iommu
[ 0.544214] mpp_vepu2 fdee0000.vepu: probe device
[ 0.544728] mpp_vepu2 fdee0000.vepu: probing finish
[ 0.545251] iommu: Adding device fdef0000.iep to group 4
[ 0.545288] mpp-iep2 fdef0000.iep: Linked as a consumer to fdef0800.iommu
[ 0.545425] mpp-iep2 fdef0000.iep: probe device
[ 0.545866] mpp-iep2 fdef0000.iep: allocate roi buffer failed
[ 0.546029] mpp-iep2 fdef0000.iep: probing finish
[ 0.546501] iommu: Adding device fded0000.jpegd to group 2
[ 0.546529] mpp_jpgdec fded0000.jpegd: Linked as a consumer to fded0480.iommu
[ 0.546669] mpp_jpgdec fded0000.jpegd: probe device
[ 0.547179] mpp_jpgdec fded0000.jpegd: probing finish
[ 0.547679] iommu: Adding device fdf80200.rkvdec to group 6
[ 0.547720] mpp_rkvdec2 fdf80200.rkvdec: Linked as a consumer to fdf80800.iommu
[ 0.547947] mpp_rkvdec2 fdf80200.rkvdec: probing start
[ 0.548123] mpp_rkvdec2 fdf80200.rkvdec: 16 task capacity link mode detected
[ 0.548446] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_a is not found!
[ 0.548459] rkvdec2_init:661: No niu aclk reset resource define
[ 0.548471] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_h is not found!
[ 0.548478] rkvdec2_init:664: No niu hclk reset resource define
[ 0.548665] mpp_rkvdec2 fdf80200.rkvdec: sram_start 0x00000000fdcc0000
[ 0.548686] mpp_rkvdec2 fdf80200.rkvdec: rcb_iova 0x0000000010000000
[ 0.548701] mpp_rkvdec2 fdf80200.rkvdec: sram_size 45056
[ 0.548710] mpp_rkvdec2 fdf80200.rkvdec: rcb_size 65536
[ 0.548721] mpp_rkvdec2 fdf80200.rkvdec: min_width 512
[ 0.548783] mpp_rkvdec2 fdf80200.rkvdec: link mode probe finish
[ 0.548858] mpp_rkvdec2 fdf80200.rkvdec: probing finish
[ 0.549160] mpp_service mpp-srv: probe success
[ 0.554707] dma-pl330 fe530000.dmac: Loaded driver for PL330 DMAC-241330
[ 0.554742] dma-pl330 fe530000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 0.556946] dma-pl330 fe550000.dmac: Loaded driver for PL330 DMAC-241330
[ 0.556973] dma-pl330 fe550000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 0.558231] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[ 0.559292] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[ 0.560164] fe650000.serial: ttyS1 at MMIO 0xfe650000 (irq = 60, base_baud = 1500000) is a 16550A
[ 0.562891] random: fast init done
[ 0.563200] random: crng init done
[ 0.563273] iommu: Adding device fe040000.vop to group 8
[ 0.563315] rockchip-vop2 fe040000.vop: Linked as a consumer to fe043e00.iommu
[ 0.567620] rockchip-drm display-subsystem: Linked as a consumer to fe040000.vop
[ 0.568766] rockchip-drm display-subsystem: Linked as a consumer to fe0a0000.hdmi
[ 0.570495] rockchip-drm display-subsystem: dmc is disabled
[ 0.570784] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x15, primary plane phy id: 4
[ 0.570804] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp1 assign plane mask: 0x0, primary plane phy id: -1
[ 0.570820] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x0, primary plane phy id: -1
[ 0.570971] [drm] unsupported AFBC format[3432564e]
[ 0.571029] [drm] failed to init overlay plane Cluster0-win1
[ 0.571130] rockchip-drm display-subsystem: bound fe040000.vop (ops 0xffffff8008fba6d8)
[ 0.571350] dwhdmi-rockchip fe0a0000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[ 0.571940] dwhdmi-rockchip fe0a0000.hdmi: registered DesignWare HDMI I2C bus driver
[ 0.572516] rockchip-drm display-subsystem: bound fe0a0000.hdmi (ops 0xffffff8008fbe1f8)
[ 0.572532] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 0.572540] [drm] No driver support for vblank timestamp query.
[ 0.572771] rockchip-drm display-subsystem: connector[HDMI-A-1] can't found any modes
[ 0.572834] rockchip-drm display-subsystem: can't not find any loader display
[ 0.572857] rockchip-drm display-subsystem: failed to show loader logo
[ 0.572896] [drm] Cannot find any crtc or sizes
[ 0.573626] [drm] Initialized rockchip 2.0.0 20140818 for display-subsystem on minor 0
[ 0.578893] mali fde60000.gpu: Kernel DDK version g7p1-01bet0
[ 0.579014] mali fde60000.gpu: Device initialization Deferred
[ 0.579122] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.579842] brd: module loaded
[ 0.586653] loop: module loaded
[ 0.587097] zram: Added device: zram0
[ 0.587223] lkdtm: No crash points registered, enable through debugfs
[ 0.589952] libphy: Fixed MDIO Bus: probed
[ 0.590006] CAN device driver interface
[ 0.591595] rk_gmac-dwmac fe010000.ethernet: no regulator found
[ 0.591622] rk_gmac-dwmac fe010000.ethernet: clock input or output? (input).
[ 0.591634] rk_gmac-dwmac fe010000.ethernet: TX delay(0x4e).
[ 0.591645] rk_gmac-dwmac fe010000.ethernet: RX delay(0x2c).
[ 0.591659] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no).
[ 0.591705] rk_gmac-dwmac fe010000.ethernet: clock input from PHY
[ 0.596732] rk_gmac-dwmac fe010000.ethernet: init for RGMII
[ 0.596967] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ 0.596995] rk_gmac-dwmac fe010000.ethernet: DWMAC4/5
[ 0.597014] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register supported
[ 0.597029] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine supported
[ 0.597043] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported
[ 0.597056] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported
[ 0.597097] rk_gmac-dwmac fe010000.ethernet: TSO supported
[ 0.597114] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 0.597131] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled
[ 0.728116] libphy: stmmac: probed
[ 0.733462] usbcore: registered new interface driver rndis_wlan
[ 0.733543] usbcore: registered new interface driver rtl8150
[ 0.733599] usbcore: registered new interface driver r8152
[ 0.733656] usbcore: registered new interface driver asix
[ 0.733710] usbcore: registered new interface driver ax88179_178a
[ 0.733760] usbcore: registered new interface driver cdc_ether
[ 0.733803] usbcore: registered new interface driver rndis_host
[ 0.733865] usbcore: registered new interface driver cdc_ncm
[ 0.733923] usbcore: registered new interface driver qmi_wwan_q
[ 0.733973] usbcore: registered new interface driver qmi_wwan
[ 0.734021] usbcore: registered new interface driver cdc_mbim
[ 0.735279] dwc3 fcc00000.dwc3: Failed to get clk 'ref': -2
[ 0.740755] dwc3 fd000000.dwc3: Failed to get clk 'ref': -2
[ 0.746595] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.746632] ehci-pci: EHCI PCI platform driver
[ 0.746713] ehci-platform: EHCI generic platform driver
[ 0.748985] ehci-platform fd800000.usb: EHCI Host Controller
[ 0.749167] ehci-platform fd800000.usb: new USB bus registered, assigned bus number 1
[ 0.749466] ehci-platform fd800000.usb: irq 11, io mem 0xfd800000
[ 0.761464] ehci-platform fd800000.usb: USB 2.0 started, EHCI 1.00
[ 0.761700] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 0.761720] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.761740] usb usb1: Product: EHCI Host Controller
[ 0.761749] usb usb1: Manufacturer: Linux 4.19.219 ehci_hcd
[ 0.761758] usb usb1: SerialNumber: fd800000.usb
[ 0.762203] hub 1-0:1.0: USB hub found
[ 0.762258] hub 1-0:1.0: 1 port detected
[ 0.764777] ehci-platform fd880000.usb: EHCI Host Controller
[ 0.764987] ehci-platform fd880000.usb: new USB bus registered, assigned bus number 2
[ 0.765300] ehci-platform fd880000.usb: irq 13, io mem 0xfd880000
[ 0.778103] ehci-platform fd880000.usb: USB 2.0 started, EHCI 1.00
[ 0.778321] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 0.778342] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.778362] usb usb2: Product: EHCI Host Controller
[ 0.778376] usb usb2: Manufacturer: Linux 4.19.219 ehci_hcd
[ 0.778390] usb usb2: SerialNumber: fd880000.usb
[ 0.778796] hub 2-0:1.0: USB hub found
[ 0.778844] hub 2-0:1.0: 1 port detected
[ 0.779606] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.779629] ohci-platform: OHCI generic platform driver
[ 0.779873] ohci-platform fd840000.usb: Generic Platform OHCI controller
[ 0.780050] ohci-platform fd840000.usb: new USB bus registered, assigned bus number 3
[ 0.780278] ohci-platform fd840000.usb: irq 12, io mem 0xfd840000
[ 0.838964] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[ 0.838985] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.838996] usb usb3: Product: Generic Platform OHCI controller
[ 0.839005] usb usb3: Manufacturer: Linux 4.19.219 ohci_hcd
[ 0.839014] usb usb3: SerialNumber: fd840000.usb
[ 0.839438] hub 3-0:1.0: USB hub found
[ 0.839488] hub 3-0:1.0: 1 port detected
[ 0.839991] ohci-platform fd8c0000.usb: Generic Platform OHCI controller
[ 0.840182] ohci-platform fd8c0000.usb: new USB bus registered, assigned bus number 4
[ 0.840468] ohci-platform fd8c0000.usb: irq 14, io mem 0xfd8c0000
[ 0.898957] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[ 0.898979] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.898990] usb usb4: Product: Generic Platform OHCI controller
[ 0.898999] usb usb4: Manufacturer: Linux 4.19.219 ohci_hcd
[ 0.899008] usb usb4: SerialNumber: fd8c0000.usb
[ 0.899438] hub 4-0:1.0: USB hub found
[ 0.899489] hub 4-0:1.0: 1 port detected
[ 0.901067] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller
[ 0.901275] xhci-hcd xhci-hcd.4.auto: new USB bus registered, assigned bus number 5
[ 0.901809] xhci-hcd xhci-hcd.4.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000011002010010
[ 0.901875] xhci-hcd xhci-hcd.4.auto: irq 74, io mem 0xfd000000
[ 0.902210] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 0.902231] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.902248] usb usb5: Product: xHCI Host Controller
[ 0.902262] usb usb5: Manufacturer: Linux 4.19.219 xhci-hcd
[ 0.902275] usb usb5: SerialNumber: xhci-hcd.4.auto
[ 0.902710] hub 5-0:1.0: USB hub found
[ 0.902762] hub 5-0:1.0: 1 port detected
[ 0.903109] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller
[ 0.903277] xhci-hcd xhci-hcd.4.auto: new USB bus registered, assigned bus number 6
[ 0.903306] xhci-hcd xhci-hcd.4.auto: Host supports USB 3.0 SuperSpeed
[ 0.903389] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[ 0.903522] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.19
[ 0.903542] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.903558] usb usb6: Product: xHCI Host Controller
[ 0.903572] usb usb6: Manufacturer: Linux 4.19.219 xhci-hcd
[ 0.903586] usb usb6: SerialNumber: xhci-hcd.4.auto
[ 0.904009] hub 6-0:1.0: USB hub found
[ 0.904057] hub 6-0:1.0: 1 port detected
[ 0.904533] usbcore: registered new interface driver cdc_acm
[ 0.904551] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 0.904628] usbcore: registered new interface driver cdc_wdm
[ 0.904930] usbcore: registered new interface driver uas
[ 0.905083] usbcore: registered new interface driver usb-storage
[ 0.905197] usbcore: registered new interface driver usbserial_generic
[ 0.905237] usbserial: USB Serial support registered for generic
[ 0.905299] usbcore: registered new interface driver cp210x
[ 0.905334] usbserial: USB Serial support registered for cp210x
[ 0.905432] usbcore: registered new interface driver ftdi_sio
[ 0.905468] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 0.905705] usbcore: registered new interface driver keyspan
[ 0.905741] usbserial: USB Serial support registered for Keyspan - (without firmware)
[ 0.905775] usbserial: USB Serial support registered for Keyspan 1 port adapter
[ 0.905813] usbserial: USB Serial support registered for Keyspan 2 port adapter
[ 0.905848] usbserial: USB Serial support registered for Keyspan 4 port adapter
[ 0.905911] usbcore: registered new interface driver option
[ 0.905946] usbserial: USB Serial support registered for GSM modem (1-port)
[ 0.906273] usbcore: registered new interface driver oti6858
[ 0.906310] usbserial: USB Serial support registered for oti6858
[ 0.906361] usbcore: registered new interface driver pl2303
[ 0.906395] usbserial: USB Serial support registered for pl2303
[ 0.906467] usbcore: registered new interface driver qcserial
[ 0.906507] usbserial: USB Serial support registered for Qualcomm USB modem
[ 0.906593] usbcore: registered new interface driver sierra
[ 0.906629] usbserial: USB Serial support registered for Sierra USB modem
[ 0.908013] usbcore: registered new interface driver usbtouchscreen
[ 0.908060] ============ himax_hx83102_init 1742 jjlook ==========
[ 0.908126] ============ himax_hx83102_probe 1725 jjlook ==========
[ 0.908193] cyttsp5_loader_init: Parade TTSP FW Loader Driver (Built TTDA.03.08.874312) rc=0
[ 0.908214] cyttsp5_device_access_init: Parade TTSP Device Access Driver (Built TTDA.03.08.874312) rc=0
[ 0.908596] .. rk pwm remotectl v2.0 init
[ 0.908891] input: fe6e0030.pwm as /devices/platform/fe6e0030.pwm/input/input0
[ 0.909268] remotectl-pwm fe6e0030.pwm: pwm version is 0x2130000
[ 0.909313] remotectl-pwm fe6e0030.pwm: cannot find PWR IRQ
[ 0.909335] remotectl-pwm fe6e0030.pwm: pwm sip wakeup config error!!
[ 0.909350] remotectl-pwm fe6e0030.pwm: Donot support ATF Wakeup
[ 0.910002] i2c /dev entries driver
[ 0.911969] fan53555-regulator 0-001c: FAN53555 Option[12] Rev[15] Detected!
[ 0.913417] vdd_cpu: supplied by vcc5v0_sys
[ 0.918238] rk808 0-0020: chip id: 0x8090
[ 0.918292] rk808 0-0020: No cache defaults, reading back from HW
[ 0.942012] rk808 0-0020: source: on=0x10, off=0x00
[ 0.942038] rk808 0-0020: support dcdc3 fb mode:-22, 63
[ 0.942052] rk808 0-0020: support pmic reset mode:0,0
[ 0.947470] rk808-regulator rk808-regulator: there is no dvs0 gpio
[ 0.947515] rk808-regulator rk808-regulator: there is no dvs1 gpio
[ 0.947944] vdd_logic: supplied by vcc3v3_sys
[ 0.948705] vdd_gpu: supplied by vcc3v3_sys
[ 0.949036] vcc_ddr: supplied by vcc3v3_sys
[ 0.949357] vdd_npu: supplied by vcc3v3_sys
[ 0.950032] vcc_1v8: supplied by vcc3v3_sys
[ 0.950358] vdda0v9_image: supplied by vcc3v3_sys
[ 0.951006] vdda_0v9: supplied by vcc3v3_sys
[ 0.951301] vdda0v9_pmu: supplied by vcc3v3_sys
[ 0.951646] vccio_acodec: supplied by vcc3v3_sys
[ 0.952293] vccio_sd: supplied by vcc3v3_sys
[ 0.952611] vcc3v3_pmu: supplied by vcc3v3_sys
[ 0.953267] vcca_1v8: supplied by vcc3v3_sys
[ 0.953585] vcca1v8_pmu: supplied by vcc3v3_sys
[ 0.953899] vcca1v8_image: supplied by vcc3v3_sys
[ 0.954541] vcc_3v3: supplied by vcc3v3_sys
[ 0.955222] vcc3v3_sd: supplied by vcc3v3_sys
[ 0.955637] rk817-battery rk817-battery: Failed to find matching dt id
[ 0.955895] rk817-charger rk817-charger: Failed to find matching dt id
[ 0.959065] input: rk805 pwrkey as /devices/platform/fdd40000.i2c/i2c-0/0-0020/rk805-pwrkey/input/input1
[ 0.959523] rk808-rtc rk808-rtc: device is disabled
[ 0.959552] rk808-rtc: probe of rk808-rtc failed with error -22
[ 0.968295] rtc-hym8563 2-0051: rtc core: registered hym8563 as rtc0
[ 0.969348] rtc-hym8563 2-0051: setting system clock to 2017-01-09 15:40:23 UTC (1483976423)
[ 0.974309] iommu: Adding device fdff0000.rkisp to group 7
[ 0.974359] rkisp_hw fdff0000.rkisp: Linked as a consumer to fdff1a00.iommu
[ 0.974550] rkisp_hw fdff0000.rkisp: is_thunderboot: 0
[ 0.974573] rkisp_hw fdff0000.rkisp: max input:0x0@0fps
[ 0.974607] rkisp_hw fdff0000.rkisp: can't request region for resource [mem 0xfdff0000-0xfdffffff]
[ 0.975480] rkisp rkisp-vir0: rkisp driver version: v01.07.00
[ 0.975746] rkisp rkisp-vir0: Entity type for entity rkisp-isp-subdev was not initialized!
[ 0.975776] rkisp rkisp-vir0: Entity type for entity rkisp-csi-subdev was not initialized!
[ 0.977605] usbcore: registered new interface driver uvcvideo
[ 0.977626] USB Video Class driver (1.1.1)
[ 0.977904] rockchip-iodomain fdc20000.syscon:io-domains: Linked as a consumer to regulator.24
[ 0.977949] rockchip-iodomain fdc20000.syscon:io-domains: pmuio1(3300000 uV) supplied by vcc3v3_pmu
[ 0.978075] rockchip-iodomain fdc20000.syscon:io-domains: pmuio2(3300000 uV) supplied by vcc3v3_pmu
[ 0.978212] rockchip-iodomain fdc20000.syscon:io-domains: Linked as a consumer to regulator.22
[ 0.978252] rockchip-iodomain fdc20000.syscon:io-domains: vccio1(3300000 uV) supplied by vccio_acodec
[ 0.978383] rockchip-iodomain fdc20000.syscon:io-domains: Linked as a consumer to regulator.23
[ 0.978422] rockchip-iodomain fdc20000.syscon:io-domains: vccio3(3300000 uV) supplied by vccio_sd
[ 0.978526] rockchip-iodomain fdc20000.syscon:io-domains: Linked as a consumer to regulator.18
[ 0.978556] rockchip-iodomain fdc20000.syscon:io-domains: vccio4(1800000 uV) supplied by vcc_1v8
[ 0.978648] rockchip-iodomain fdc20000.syscon:io-domains: Linked as a consumer to regulator.28
[ 0.978688] rockchip-iodomain fdc20000.syscon:io-domains: vccio5(3300000 uV) supplied by vcc_3v3
[ 0.978785] rockchip-iodomain fdc20000.syscon:io-domains: vccio6(1800000 uV) supplied by vcc_1v8
[ 0.978909] rockchip-iodomain fdc20000.syscon:io-domains: vccio7(3300000 uV) supplied by vcc_3v3
[ 0.982135] rockchip-thermal fe710000.tsadc: tsadc is probed successfully!
[ 0.983257] Bluetooth: HCI UART driver ver 2.3
[ 0.983280] Bluetooth: HCI UART protocol H4 registered
[ 0.983295] Bluetooth: HCI UART protocol ATH3K registered
[ 0.983498] Bluetooth: HCI UART protocol Broadcom registered
[ 0.983591] usbcore: registered new interface driver bfusb
[ 0.983671] usbcore: registered new interface driver btusb
[ 0.983952] cpu cpu0: leakage=40
[ 0.984008] cpu cpu0: pvtm = 86630, from nvmem
[ 0.984033] cpu cpu0: pvtm-volt-sel=1
[ 0.984881] cpu cpu0: Linked as a consumer to regulator.13
[ 0.984940] cpu cpu0: Dropping the link to regulator.13
[ 0.985578] cpu cpu0: Linked as a consumer to regulator.13
[ 0.986288] cpu cpu0: avs=0
[ 0.986357] energy_model: pd0: hertz/watts ratio non-monotonically decreasing: em_cap_state 2 >= em_cap_state1
[ 0.986567] cpu cpu0: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[ 0.990003] cpu cpu0: failed to find power_model node
[ 0.991358] sdhci: Secure Digital Host Controller Interface driver
[ 0.991377] sdhci: Copyright(c) Pierre Ossman
[ 0.991389] Synopsys Designware Multimedia Card Interface Driver
[ 0.992495] dwmmc_rockchip fe2b0000.dwmmc: IDMAC supports 32-bit address mode.
[ 0.992695] dwmmc_rockchip fe2b0000.dwmmc: Using internal DMA controller.
[ 0.992717] dwmmc_rockchip fe2b0000.dwmmc: Version ID is 270a
[ 0.992790] dwmmc_rockchip fe2b0000.dwmmc: DW MMC controller at irq 46,32 bit host data width,256 deep fifo
[ 0.992969] dwmmc_rockchip fe2b0000.dwmmc: Linked as a consumer to regulator.23
[ 1.005295] mmc_host mmc1: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[ 1.018547] dwmmc_rockchip fe2c0000.dwmmc: IDMAC supports 32-bit address mode.
[ 1.018994] dwmmc_rockchip fe2c0000.dwmmc: Using internal DMA controller.
[ 1.019019] dwmmc_rockchip fe2c0000.dwmmc: Version ID is 270a
[ 1.019083] dwmmc_rockchip fe2c0000.dwmmc: DW MMC controller at irq 47,32 bit host data width,256 deep fifo
[ 1.019241] dwmmc_rockchip fe2c0000.dwmmc: allocated mmc-pwrseq
[ 1.019261] mmc_host mmc2: card is non-removable.
[ 1.032383] mmc_host mmc2: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[ 1.045349] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.046549] mmc0: Unknown controller version (5). You may experience problems.
[ 1.077299] mmc2: queuing unknown CIS tuple 0x80 (2 bytes)
[ 1.078153] mmc0: SDHCI controller on fe310000.sdhci [fe310000.sdhci] using ADMA
[ 1.079013] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
[ 1.079853] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.080308] usbcore: registered new interface driver usbhid
[ 1.080325] usbhid: USB HID core driver
[ 1.080734] rockchip,bus bus-npu: Linked as a consumer to regulator.14
[ 1.080763] rockchip,bus bus-npu: Failed to get leakage
[ 1.080822] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
[ 1.080846] rockchip,bus bus-npu: pvtm = 86630, from nvmem
[ 1.080870] rockchip,bus bus-npu: pvtm-volt-sel=1
[ 1.081132] rockchip,bus bus-npu: avs=0
[ 1.083629] rockchip-saradc fe720000.saradc: Linked as a consumer to regulator.25
[ 1.084074] mmc2: queuing unknown CIS tuple 0x80 (7 bytes)
[ 1.084363] rksfc_base v1.1 2016-01-08
[ 1.085254] rksfc fe300000.sfc: rksfc_probe clk rate = 50000000
[ 1.085312] rkflash_dev_init enter
[ 1.085337] sfc nor id: ef 60 18
[ 1.085357] rkflash[1] init success
[ 1.086377] sfc_nor_mtd_init register mtd succuss
[ 1.086397] rkflash_dev_init device register as mtd dev, ret= 0
[ 1.087141] usbcore: registered new interface driver snd-usb-audio
[ 1.087969] mmc2: queuing unknown CIS tuple 0x81 (9 bytes)
[ 1.089843] rk817-codec rk817-codec: DMA mask not set
[ 1.090614] rk817_codec_parse_dt_property: rk809 hp adc effective value of detection 917~965
[ 1.090645] invalid rk817->hp_det_gpio: -2
[ 1.090658] invalid gpio: -2
[ 1.096988] Initializing XFRM netlink socket
[ 1.097513] NET: Registered protocol family 10
[ 1.098272] Segment Routing with IPv6
[ 1.098370] NET: Registered protocol family 17
[ 1.098398] NET: Registered protocol family 15
[ 1.098438] can: controller area network core (rev 20170425 abi 9)
[ 1.098572] NET: Registered protocol family 29
[ 1.098590] can: raw protocol (rev 20170425)
[ 1.098620] can: broadcast manager protocol (rev 20170425 t)
[ 1.098643] can: netlink gateway (rev 20170425) max_hops=1
[ 1.098907] Bluetooth: RFCOMM socket layer initialized
[ 1.098951] Bluetooth: RFCOMM ver 1.11
[ 1.099006] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 1.099027] Bluetooth: HIDP socket layer initialized
[ 1.099070] [BT_RFKILL]: Enter rfkill_rk_init
[ 1.099079] [WLAN_RFKILL]: Enter rfkill_wlan_init
[ 1.099667] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[ 1.099734] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6356s
[ 1.099751] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[ 1.099762] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[ 1.099807] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,host_wake_irq = 74, flags = 0.
[ 1.099819] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[ 1.099834] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[ 1.099847] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 1
[ 1.099859] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[ 1.100582] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 77.
[ 1.100621] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 79.
[ 1.100644] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 80.
[ 1.100665] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 81.
[ 1.100738] [BT_RFKILL]: Request irq for bt wakeup host
[ 1.100847] [BT_RFKILL]: ** disable irq
[ 1.100978] [BT_RFKILL]: bt_default device registered.
[ 1.101133] Key type dns_resolver registered
[ 1.101411] flash vendor_init_thread!
[ 1.101469] flash vendor storage:20170308 ret = -1
[ 1.103346] Loading compiled-in X.509 certificates
[ 1.104026] pstore: Using compression: deflate
[ 1.105185] rga2: Driver loaded successfully ver:3.2.63318
[ 1.105606] rga2: Module initialized.
[ 1.110779] mmc0: new HS200 MMC card at address 0001
[ 1.112105] mmcblk0: mmc0:0001 8GTF4R 7.28 GiB
[ 1.112832] mmcblk0boot0: mmc0:0001 8GTF4R partition 1 4.00 MiB
[ 1.113555] mmcblk0boot1: mmc0:0001 8GTF4R partition 2 4.00 MiB
[ 1.113822] mmcblk0rpmb: mmc0:0001 8GTF4R partition 3 512 KiB, chardev (239:0)
[ 1.116991] mmcblk0: p1 p2 p3 p4 p5 p6 p7
[ 1.133224] mali fde60000.gpu: Kernel DDK version g7p1-01bet0
[ 1.133285] input: adc-keys as /devices/platform/adc-keys/input/input2
[ 1.133446] mali fde60000.gpu: Linked as a consumer to regulator.15
[ 1.133621] mali fde60000.gpu: dev_pm_opp_set_regulators: no regulator (shadercores) found: -19
[ 1.133740] mali fde60000.gpu: leakage=12
[ 1.133788] mali fde60000.gpu: pvtm = 86630, from nvmem
[ 1.134215] mali fde60000.gpu: avs=0
[ 1.134240] W : [File] : drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] : 112; [Func] : kbase_platform_rk_init(); power-off-delay-ms not available.
[ 1.134697] asoc-simple-card hdmi-sound: i2s-hifi <-> fe400000.i2s mapping ok
[ 1.134731] mali fde60000.gpu: GPU identified as 0x2 arch 7.4.0 r1p0 status 0
[ 1.134848] mali fde60000.gpu: No priority control manager is configured
[ 1.134860] mali fde60000.gpu: No memory group manager is configured
[ 1.135392] mali fde60000.gpu: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0 h_table=0
[ 1.135991] mali fde60000.gpu: Probed as mali0
[ 1.141009] asoc-simple-card rk809-sound: rk817-hifi <-> fe410000.i2s mapping ok
[ 1.141043] asoc-simple-card rk809-sound: ASoC: no source widget found for MICBIAS1
[ 1.141056] asoc-simple-card rk809-sound: ASoC: Failed to add route MICBIAS1 -> direct -> Mic Jack
[ 1.141064] asoc-simple-card rk809-sound: ASoC: no source widget found for Mic Jack
[ 1.141071] asoc-simple-card rk809-sound: ASoC: Failed to add route Mic Jack -> direct -> IN1P
[ 1.141079] asoc-simple-card rk809-sound: ASoC: no source widget found for HPOL
[ 1.141089] asoc-simple-card rk809-sound: ASoC: Failed to add route HPOL -> direct -> Headphone Jack
[ 1.141100] asoc-simple-card rk809-sound: ASoC: no source widget found for HPOR
[ 1.141110] asoc-simple-card rk809-sound: ASoC: Failed to add route HPOR -> direct -> Headphone Jack
[ 1.143511] register spi return v = :0
[ 1.143536] dhd_module_init: in Dongle Host Driver, version 100.10.545.9 (r826445-20200316-8)
[ 1.143547] ======== dhd_wlan_init_plat_data ========
[ 1.143557] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter
[ 1.143630] dhd_wlan_init_gpio: WL_HOST_WAKE=-1, oob_irq=102, oob_irq_flags=0x414
[ 1.143641] dhd_wlan_init_gpio: WL_REG_ON=-1
[ 1.143652] dhd_wifi_platform_load: Enter
[ 1.143664] Power-up adapter 'DHD generic adapter'
[ 1.143694] wifi_platform_set_power = 1, delay: 200 msec
[ 1.143706] ======== PULL WL_REG_ON(-1) HIGH! ========
[ 1.143716] [WLAN_RFKILL]: rockchip_wifi_power: 1
[ 1.143726] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
[ 1.143735] [WLAN_RFKILL]: wifi turn on power [GPIO-1-0]
[ 1.178942] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[ 1.180969] mmc2: new high speed SDIO card at address 0001
[ 1.223425] vendor storage:20190527 ret = 0
[ 1.275622] devfreq fde60000.gpu: Couldn't update frequency transition information.
[ 1.448321] wifi_platform_bus_enumerate device present 1
[ 1.448385] ======== Card detection to detect SDIO card! ========
[ 1.448410] mmc2:mmc host rescan start!
[ 1.464562] bcmsdh_register: register client driver
[ 1.464815] bcmsdh_sdmmc_probe: Enter num=1
[ 1.465600] bcmsdh_sdmmc_probe: Enter num=2
[ 1.465616] bus num (host idx)=2, slot num (rca)=1
[ 1.465622] found adapter info 'DHD generic adapter'
[ 1.465789] sdioh_attach: set sd_f2_blocksize 256
[ 1.465904] sdioh_attach: sd clock rate = 0
[ 1.466522] dhdsdio_probe : no mutex held. set lock
[ 1.466755] F1 signature read @0x18000000=0x1541a9a6
[ 1.472885] F1 signature OK, socitype:0x1 chip:0xa9a6 rev:0x1 pkg:0x4
[ 1.475115] DHD: dongle ram size is set to 524288(orig 524288) at 0x0
[ 1.475420] [dhd] dhd_conf_set_chiprev : chip=0xa9a6, chiprev=1
[ 1.476197] [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 1.476215] [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 1.476451] dhd_log_dump_init: kernel log buf size = 256KB; logdump_prsrv_tailsize = 80KB; limit prsrv tail size to = 38KB
[ 1.477181] dhd_attach(): thread:dhd_watchdog_thread:63 started
[ 1.477289] dhd_attach(): thread:dhd_dpc:64 started
[ 1.477405] dhd_attach(): thread:dhd_rxf:65 started
[ 1.477422] dhd_deferred_work_init: work queue initialized
[ 1.477436] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 2
[ 1.477513] get_mem_val_from_file: File [/data/misc/wifi/.memdump.info] doesn't exist
[ 1.477527] dhd_get_memdump_info: MEMDUMP ENABLED = 3
[ 1.477542] sdioh_cis_read: func_cis_ptr[0]=0x1070
[ 1.486495] dhdsdio_probe_init: making DHD_BUS_DOWN
[ 1.486656] Dongle Host Driver, version 100.10.545.9 (r826445-20200316-8)
[ 1.487139] Register interface [wlan0] MAC: 08:e9:f6:6b:0b:ce
[ 1.487139]
[ 1.487250] dhd_dbg_detach_pkt_monitor, 2100
[ 1.487265] dhd_bus_devreset: == Power OFF ==
[ 1.487473] dhd_bus_stop: making DHD_BUS_DOWN
[ 1.487514] bcmsdh_oob_intr_unregister: Enter
[ 1.487526] bcmsdh_oob_intr_unregister: irq is not registered
[ 1.487539] dhd_bus_devreset: making dhdpub up FALSE
[ 1.487550] dhd_txglom_enable: enable 0
[ 1.487559] dhd_bus_devreset: making DHD_BUS_DOWN
[ 1.487569] dhd_bus_devreset: WLAN OFF DONE
[ 1.487618] wifi_platform_set_power = 0, delay: 0 msec
[ 1.487632] ======== PULL WL_REG_ON(-1) LOW! ========
[ 1.487641] [WLAN_RFKILL]: rockchip_wifi_power: 0
[ 1.487660] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
[ 1.487670] [WLAN_RFKILL]: wifi shut off power [GPIO-1-1]
[ 1.487681] dhdsdio_probe : the lock is released.
[ 1.488402] dhd_module_init: Exit err=0
[ 1.488771] ==gsl_ts_init==
[ 1.488829] ret=0
[ 1.489617] iommu: Adding device fde40000.npu to group 0
[ 1.489641] RKNPU fde40000.npu: Linked as a consumer to fde4b000.iommu
[ 1.490093] RKNPU fde40000.npu: RKNPU: rknpu iommu is enabled, using iommu mode
[ 1.490234] RKNPU fde40000.npu: Linked as a consumer to regulator.17
[ 1.490261] RKNPU fde40000.npu: can't request region for resource [mem 0xfde40000-0xfde4ffff]
[ 1.490709] [drm] Initialized rknpu 0.4.2 20210701 for fde40000.npu on minor 1
[ 1.490981] RKNPU fde40000.npu: leakage=6
[ 1.491024] RKNPU fde40000.npu: pvtm = 86630, from nvmem
[ 1.491485] RKNPU fde40000.npu: avs=0
[ 1.492101] RKNPU fde40000.npu: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[ 1.492130] RKNPU fde40000.npu: failed to find power_model node
[ 1.492142] RKNPU fde40000.npu: RKNPU: failed to initialize power model
[ 1.492152] RKNPU fde40000.npu: RKNPU: failed to get dynamic-coefficient
[ 1.493157] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 1.498269] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 1.498917] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 1.498935] cfg80211: failed to load regulatory.db
[ 1.499736] rockchip-pm rockchip-suspend: not set pwm-regulator-config
[ 1.500366] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 417; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '19:15:57', on 'Apr 18 2022'.
[ 1.500758] Mali:
[ 1.500760] Mali device driver loaded
[ 1.501014] xc7160 4-001b: T-chip firefly camera driver version: 00.01.02
[ 1.501280] xc7160 4-001b: Failed to get power-gpios, maybe no use
[ 1.501380] xc7160 4-001b: 4-001b supply avdd not found, using dummy regulator
[ 1.501483] xc7160 4-001b: Linked as a consumer to regulator.0
[ 1.501523] xc7160 4-001b: 4-001b supply dovdd not found, using dummy regulator
[ 1.501590] xc7160 4-001b: 4-001b supply dvdd not found, using dummy regulator
[ 1.501647] xc7160 4-001b: could not get default pinstate
[ 1.501660] xc7160 4-001b: could not get sleep pinstate
[ 1.501680] xc7160 4-001b: Success to get xc7160 endpoint data lanes, dts uses 4 lanes
[ 1.501690] xc7160 4-001b: xc7160 num data lanes is 4
[ 1.517649] xc7160 4-001b: write XC7160_REG_HIGH_SELECT failed
[ 1.517923] xc7160: probe of 4-001b failed with error -5
[ 1.517997] rkisp rkisp-vir0: clear unready subdev num: 4
[ 1.518016] rockchip-csi2-dphy0: No link between dphy and sensor
[ 1.518676] rockchip-csi2-dphy0: No link between dphy and sensor
[ 1.518694] rkisp-vir0: update sensor failed
[ 1.521503] ret 1024 0
[ 1.521841] ALSA device list:
[ 1.521858] #0: rockchip,hdmi
[ 1.521865] #1: rockchip,rk809-codec
[ 1.525257] Freeing unused kernel memory: 1600K
[ 1.548359] rk-pcie 3c0000000.pcie: PCIe Linking... LTSSM is 0x3
[ 1.551793] Run /init as init process
Loading, please wait...
/dev/console is Ok
starting version 237
[ 2.000348] phy phy-fe8a0000.usb2-phy.1: charger = USB_SDP_CHARGER
[ 2.561718] rk-pcie 3c0000000.pcie: PCIe Linking... LTSSM is 0x3
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done.
Begin: Running /scripts/nfs-premount ... done.
IP-Config: eth0 hardware address f2:74:4c:53:9e:98 mtu 1500
[ 3.224998] [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 3.225064] Generic PHY stmmac-1:00: [phy_probe-1992] led_status_value = 0x2f60
[ 3.225959] Generic PHY stmmac-1:00: phy_rtl8211f_led_fixup
[ 3.247106] Generic PHY stmmac-1:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=stmmac-1:00, irq=POLL)
[ 3.259097] dwmac4: Master AXI performs any burst length
[ 3.259144] rk_gmac-dwmac fe010000.ethernet eth0: No Safety Features support found
[ 3.259169] rk_gmac-dwmac fe010000.ethernet eth0IP-Config: eth0 guessed broad:cast address 192.168.154.255
pEEE 1588-2008 Advanced TimestIP-Config: eth0 complete:am
address: 192.168.154.10 b roadcast: 192.168.154.supported255 netmask: 255.255.255.0
dns0 : 0.0.0.0
dns1 : 0.0.0.0
rootserver: 192.168.154.134 rootpath:
filename :
[ 3.259538] rk_gmac-dwmac fe010000.ethernet eth0: registered PTP clock
[ 3.260127] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3.260159] [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 3.260297] [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
no search or nameservers found in /run/net-eth0.conf /run/net-eth0.conf /run/net6-*.conf
[ 3.575033] rk-pcie 3c0000000.pcie: PCIe Linking... LTSSM is 0x3
[ 4.588376] rk-pcie 3c0000000.pcie: PCIe Linking... LTSSM is 0x3
[ 5.283815] rk_gmac-dwmac fe010000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 5.283989] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 5.284306] [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
done.
Begin: Running /scripts/nfs-bottom ... done.
Begin: Running /scripts/init-bottom ... Warning: Something odd, no /lib/modules/4.19.219 in initramfs.
done.
[ 5.601471] rk-pcie 3c0000000.pcie: PCIe Linking... LTSSM is 0x3
[ 5.962066] systemd[1]: System time before build time, advancing clock.
[ 6.007979] systemd[1]: Failed to insert module 'autofs4': No such file or directory
[ 6.035694] systemd[1]: Configuration file /etc/systemd/system.conf is marked executable. Please remove executable permission bits. Proceeding anyway.
[ 6.040422] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 6.042863] systemd[1]: Detected architecture arm64.
Welcome to Ubuntu 18.04.6 LTS!
[ 6.065321] systemd[1]: Set hostname to <firefly>.
[ 6.071579] [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 6.072082] [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 6.442551] systemd[1]: Configuration file /lib/systemd/system/system.slice is marked executable. Please remove executable permission bits. Proceeding anyway.
[ 6.446875] systemd[1]: Configuration file /lib/systemd/system/slices.target is marked executable. Please remove executable permission bits. Proceeding anyway.
[ 6.451095] systemd[1]: Configuration file /lib/systemd/system/shutdown.target is marked executable. Please remove executable permission bits. Proceeding anyway.
[ 6.457463] systemd[1]: Configuration file /lib/systemd/system/graphical.target is marked executable. Please remove executable permission bits. Proceeding anyway.
[ 6.467536] systemd[1]: Configuration file /lib/systemd/system/systemd-update-utmp-runlevel.service is marked executable. Please remove executable permission bits. Proceeding anyway.
[ 6.472692] systemd[1]: Configuration file /lib/systemd/system/systemd-journald.socket is marked executable. Please remove executable permission bits. Proceeding anyway.
[ 6.478016] systemd[1]: Configuration file /lib/systemd/system/systemd-journald.service is marked executable. Please remove executable permission bits. Proceeding anyway.
[ 6.614882] rk-pcie 3c0000000.pcie: PCIe Linking... LTSSM is 0x3
[ OK ] Started Forward Password Requests to Wall Directory Watch.
[ OK ] Created slice System Slice.
[ OK ] Listening on udev Kernel Socket.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ OK ] Listening on Syslog Socket.
[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ OK ] Listening on udev Control Socket.
[ OK ] Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Reached target Paths.
[ OK ] Listening on Journal Socket (/dev/log).
[ OK ] Created slice User and Session Slice.
[ OK ] Reached target Slices.
[ OK ] Reached target Swap.
[ OK ] Listening on Journal Socket.
Starting Load Kernel Modules...
Starting udev Coldplug all Devices...
Mounting Kernel Debug File System...
Starting Set the console keyboard layout...
[ OK ] Reached target Remote File Systems.
Starting Create Static Device Nodes in /dev...
Starting Journal Service...
Starting Remount Root and Kernel File Systems...
[ OK ] Reached target Local Encrypted Volumes.
[ 7.628148] rk-pcie 3c0000000.pcie: PCIe Linking... LTSSM is 0x3
[ OK ] Started Load Kernel Modules.
[ 7.674698] systemd-journald[264]: Configuration file /etc/systemd/journald.conf is marked executable. Please remove executable permission bits. Proceeding anyway.
[ OK ] Mounted Kernel Debug File System.
[ OK ] Started Remount Root and Kernel File Systems.
Starting Load/Save Random Seed...
Mounting FUSE Control File System...
Mounting Kernel Configuration File System...
Starting Apply Kernel Variables...
[ OK ] Mounted FUSE Control File System.
[ OK ] Started Load/Save Random Seed.
[ OK ] Mounted Kernel Configuration File System.
[ OK ] Started Create Static Device Nodes in /dev.
Starting udev Kernel Device Manager...
[ OK ] Started Apply Kernel Variables.
[ OK ] Started udev Coldplug all Devices.
[ OK ] Started Journal Service.
Starting Flush Journal to Persistent Storage...
[ OK ] Started Set the console keyboard layout.
[ OK ] Reached target Local File Systems (Pre).
[ OK ] Reached target Local File Systems.
Starting Set console font and keymap...
[ OK ] Started Flush Journal to Persistent Storage.
Starting Create Volatile Files and Directories...
[ OK ] Started udev Kernel Device Manager.
Starting Network Service...
[ OK ] Started Network Service.
[ 11.681672] rk-pcie 3c0000000.pcie: PCIe Link Fail
[ 11.681754] rk-pcie 3c0000000.pcie: failed to initialize host
|
|