| 正在用1126 点一个普通RGB屏幕，按照文档写了DTSI文件，屏幕还是无法点亮，连背光都不正常？进系统看VOP也是disabled的。是否还是需要去改驱动的源码才能实现 。麻烦大神们帮忙看看。 启动LOG如下： DDR Version V1.08 20210825 LPDDR4, 328MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS=1 Die BW=16 Size=1024MB change to: 328MHz change to: 528MHz change to: 784MHz change to: 924MHz(final freq) out U-Boot SPL board init U-Boot SPL 2017.09(u-boot commit id: 617c0aeae793895dfbcfad2e0d67ce0620736a93)(sdk version: rv1126_rv1109_linux_release_20221222_v2.2.5d.xml)-g617c0aeae7 #alientek (Feb 11 2023 - 15:21:40) unknown raw ID phN unrecognized JEDEC id bytes: 00, 00, 00 Trying to boot from MMC2 MMC: no card present mmc_init: -123, time 1 spl: mmc init failed with error: -123 Trying to boot from MMC1 SPL: A/B-slot: _a, successful: 0, tries-remain: 7 ## Verified-boot: 0 ## Checking optee 0x08400000 (gzip @0x08600000) ... sha256(0e4f759f73...) + sha256(447872e443...) + OK ## Checking uboot 0x00400000 (gzip @0x00600000) ... sha256(03c5d20fff...) + sha256(4a9de5a3d8...) + OK ## Checking fdt 0x004b6b1c ... sha256(80f00e7967...) + OK Jumping to U-Boot(0x00400000) via OP-TEE(0x08400000) Total: 148.716 ms I/TC: I/TC: cpu feature:0x0 I/TC: RV1126 SoC I/TC: cpu_st=0xe0 I/TC: Next entry point address: 0x00400000 I/TC: OP-TEE version: 3.13.0-549-gef7f159d #derrick.huang (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05)) #1 Thu Oct 28 10:52:10 CST 2021 arm I/TC: Primary CPU initializing I/TC: Primary CPU switching to normal world boot U-Boot 2017.09(u-boot commit id: 617c0aeae793895dfbcfad2e0d67ce0620736a93)(sdk version: rv1126_rv1109_linux_release_20221222_v2.2.5d.xml)-g617c0aeae7 #alientek (Feb 11 2023 - 15:21:40 +0800) Model: Rockchip RV1126 Evaluation Board PreSerial: 2, raw, 0xff570000 DRAM: 1021.7 MiB Sysmem: init Relocation Offset: 00000000 Relocation fdt: 3bbf98f0 - 3bbfedd4 CR: M/C/I Using default environment dwmmc@ffc50000: 0, dwmmc@ffc60000: 1 Bootdev(atags): mmc 0 MMC0: HS200, 200Mhz PartType: EFI boot mode: None FIT: no signed, no conf required DTB: rk-kernel.dtb HASH(c): OK I2c0 speed: 400000Hz PMIC: RK8090 (on=0x40, off=0x00) vdd_npu_vepu 800000 uV vdd_arm 800000 uV io-domain: OK Warn: can't find connect driver stdio_add_devices: Video device failed (ret=-19) Model: Firefly Core-RV1126-JD4 BE-45 Board CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A) apll 816000 KHz dpll 462000 KHz gpll 1188000 KHz cpll 500000 KHz hpll 1400000 KHz aclk_pdbus 500000 KHz hclk_pdbus 198000 KHz pclk_pdbus 99000 KHz aclk_pdphp 297000 KHz hclk_pdphp 198000 KHz hclk_pdaudio 148500 KHz hclk_pdcore 198000 KHz pclk_pdpmu 99000 KHz Net: eth0: ethernet@ffc40000 Hit key to stop autoboot('CTRL+C'): 0 ## Booting FIT Image at 0x3aa27ac0 with size 0x00fcee00 Fdt Ramdisk skip relocation ## Loading kernel from FIT Image at 3aa27ac0 ... Using 'conf' configuration optee api revision: 2.0 TEEC: Waring: Could not find security partition ## Verified-boot: 0 Trying 'kernel' kernel subimage Description: unavailable Type: Kernel Image Compression: uncompressed Data Start: 0x3aa40cc0 Data Size: 7312056 Bytes = 7 MiB Architecture: ARM OS: Linux Load Address: 0x02008000 Entry Point: 0x02008000 Hash algo: sha256 Hash value: cc37d1894f48bd6ffb1a08076b7264d499dbef05a0b8243c6160ba00fed9a3b6 Verifying Hash Integrity ... sha256+ OK ## Loading ramdisk from FIT Image at 3aa27ac0 ... Using 'conf' configuration Trying 'ramdisk' ramdisk subimage Description: unavailable Type: RAMDisk Image Compression: uncompressed Data Start: 0x3b13a0c0 Data Size: 9160505 Bytes = 8.7 MiB Architecture: ARM OS: Linux Load Address: 0x0a200000 Entry Point: unavailable Hash algo: sha256 Hash value: 34c8dbec64a0c800281419dccd445b0b6ff60dcb9c431584b823cc4088347bde Verifying Hash Integrity ... sha256+ OK Loading ramdisk from 0x3b13a0c0 to 0x0a200000 ## Loading fdt from FIT Image at 3aa27ac0 ... Using 'conf' configuration Trying 'fdt' fdt subimage Description: unavailable Type: Flat Device Tree Compression: uncompressed Data Start: 0x3aa282c0 Data Size: 100616 Bytes = 98.3 KiB Architecture: ARM Load Address: 0x08300000 Hash algo: sha256 Hash value: 6831f654d9c4801077f7157f9ad0a90a2a1225bb49836e7bb45e49ff6c7d8677 Verifying Hash Integrity ... sha256+ OK Loading fdt from 0x08300000 to 0x08300000 Booting using the fdt blob at 0x08300000 Loading Kernel Image from 0x3aa40cc0 to 0x02008000 ... OK 'reserved-memory' ramoops@8000000: addr=8000000 size=100000 Using Device Tree in place at 08300000, end 0831b907 Adding bank: 0x00000000 - 0x08400000 (size: 0x08400000) Adding bank: 0x08648000 - 0x40000000 (size: 0x379b8000) Total: 444.826 ms Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0xf00 [ 0.000000] Linux version 4.19.111 (alientek@ubuntu) (kernel commit id: 618d4940d48a66d78328cb3e57cd74ef9e49cc3e) (sdk version: rv1126_rv1109_linux_release_20221222_v2.2.5d.xml) (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05)) #1 SMP PREEMPT Wed Feb 8 16:52:46 CST 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Firefly Core-RV1126-JD4 BE-45 Board [ 0.000000] earlycon: uart8250 at MMIO32 0xff570000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'drm-logo@00000000': base 0x00000000, size 0 MiB [ 0.000000] Reserved memory: created CMA memory pool at 0x3f800000, size 8 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x2f800000, size 256 MiB [ 0.000000] OF: reserved mem: initialized node isp, compatible id shared-dma-pool [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 15 pages/cpu s32204 r8192 d21044 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 259512 [ 0.000000] Kernel command line: user_debug=31 storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal ro rootwait earlycon=uart8250,mmio32,0xff570000 console=ttyFIQ0 root=PARTLABEL=rootfs rootfstype=ext4 overlayroot=device:dev=PARTLABEL=userdata,fstype=ext4,mkfs=1 cgroup_enable=memory swapaccount=1 snd_aloop.index=7 net.ifnames=0 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 741768K/1046240K available (9216K kernel code, 423K rwdata, 2468K rodata, 1024K init, 321K bss, 34136K reserved, 270336K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xb0000000 - 0xf0000000 (1024 MB) [ 0.000000] pkmap : 0xafe00000 - 0xb0000000 ( 2 MB) [ 0.000000] modules : 0xaf000000 - 0xafe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (10208 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 424 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 322 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: random: get_random_bytes called from start_kernel+0x328/0x4ac with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000010] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000757] Switching to timer-based delay loop, resolution 41ns [ 0.002645] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000) [ 0.003608] pid_max: default: 4096 minimum: 301 [ 0.004221] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.004847] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.006295] CPU: Testing write buffer coherency: ok [ 0.007138] /cpus/cpu@f00 missing clock-frequency property [ 0.007663] /cpus/cpu@f01 missing clock-frequency property [ 0.008183] /cpus/cpu@f02 missing clock-frequency property [ 0.008704] /cpus/cpu@f03 missing clock-frequency property [ 0.009221] CPU0: thread -1, cpu 0, socket 15, mpidr 80000f00 [ 0.010539] Setting up static identity map for 0x100000 - 0x100060 [ 0.011285] rcu: Hierarchical SRCU implementation. [ 0.012371] smp: Bringing up secondary CPUs ... I/TC: Secondary CPU 1 initializing I/TC: Secondary CPU 1 switching to normal world boot I/TC: Secondary CPU 2 initializing I/TC: Secondary CPU 2 switching to normal world boot I/TC: Secondary CPU 3 initializing I/TC: Secondary CPU 3 switching to normal world boot [ 0.014431] CPU1: thread -1, cpu 1, socket 15, mpidr 80000f01 [ 0.016164] CPU2: thread -1, cpu 2, socket 15, mpidr 80000f02 [ 0.017904] CPU3: thread -1, cpu 3, socket 15, mpidr 80000f03 [ 0.018042] smp: Brought up 1 node, 4 CPUs [ 0.020045] SMP: Total of 4 processors activated (192.00 BogoMIPS). [ 0.020626] CPU: All CPU(s) started in SVC mode. [ 0.021960] devtmpfs: initialized [ 0.048771] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.048821] Unpacking initramfs... [ 0.050132] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns [ 0.051127] futex hash table entries: 16 (order: -2, 1024 bytes) [ 0.051941] pinctrl core: initialized pinctrl subsystem [ 0.053729] NET: Registered protocol family 16 [ 0.055064] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.057738] cpuidle: using governor menu [ 0.058142] Registered FIQ tty driver [ 0.059309] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.060085] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.062944] console [pstore-1] enabled [ 0.063684] pstore: Registered ramoops as persistent store backend [ 0.064268] ramoops: attached 0x100000@0x8000000, ecc: 0/0 [ 0.114386] cryptd: max_cpu_qlen set to 1000 [ 0.115837] fiq debugger fiq mode enabled [[ 0.116674] console [ttyFIQ0] enabled 0.116674] console [ttyFIQ0] enabled [ 0.117360] bootconsole [uart8250] disabled [ 0.117360] bootconsole [uart8250] disabled [ 0.118075] Registered fiq debugger ttyFIQ0 [ 0.118811] rockchip-pm rockchip-suspend: not set pwm-regulator-config [ 0.123881] rk_iommu ffb00f00.iommu: version = 1 [ 0.124665] rk_iommu ffb20800.iommu: version = 1 [ 0.125211] rk_iommu ffb60e00.iommu: version = 1 [ 0.125772] rk_iommu ffb80480.iommu: version = 1 [ 0.126191] rk_iommu ffb90800.iommu: version = 1 [ 0.126629] rk_iommu ffbb0f00.iommu: version = 1 [ 0.127627] SCSI subsystem initialized [ 0.127972] usbcore: registered new interface driver usbfs [ 0.128081] usbcore: registered new interface driver hub [ 0.128221] usbcore: registered new device driver usb [ 0.128379] media: Linux media interface: v0.10 [ 0.128471] videodev: Linux video capture interface: v2.00 [ 0.128545] pps_core: LinuxPPS API ver. 1 registered [ 0.128569] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.128617] PTP clock support registered [ 0.130168] Advanced Linux Sound Architecture Driver Initialized. [ 0.130860] Bluetooth: Core ver 2.22 [ 0.130952] NET: Registered protocol family 31 [ 0.130982] Bluetooth: HCI device and connection manager initialized [ 0.131016] Bluetooth: HCI socket layer initialized [ 0.131046] Bluetooth: L2CAP sockeyer initialized [ 0.131115] Bluetooth: SCO socket layer init86] rockchip-cpuinfo cpuinfo: SoC: 11260000 [ 0.131727] rofo: Serial : c6718f8a4b9bc3cd [ 0.132995] clocksource: Swith_sys_counter _listen_portaddr_hash hash table entries: 512 (order: 0, 6144 by TCP established hash table entries: 8192 (order: 3, 32768 bytesbind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.13es configured (established 8192 bind 8192) [ 0.137395] UDP h512 (order: 2, 16384 bytes) [ 0.137482] UDP-Lite hash table , 16384 bytes) [ 0.137753] NET: Registered protocol family 1 perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters42684] Initialise system trusted keyrings [ 0.142953] workin=29 max_order=18 bucket_order=0 [ 0.150564] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.153416] Key type asymmetric registered [ 0.153457] Asymmetric key parser 'x509' registered [ 0.153535] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 0.153564] io scheduler noop registered [ 0.153587] io scheduler deadline registered [ 0.153783] io scheduler cfq registered (default) [ 0.153815] io scheduler mq-deadline registered [ 0.153838] io scheduler kyber registered [ 0.154003] io scheduler bfq registered [ 0.158349] phy phy-ff4c0000.usb2-phy.1: Linked as a consumer to regulator.4 [ 0.160590] phy phy-ff4c8000.usb2-phy.2: Linked as a consumer to regulator.3 [ 0.164557] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 0.164717] pwm-backlight backlight: Linked as a consumer to regulator.0 [ 0.165111] mpp_service mpp-srv: 92c80ddf68f6 author: Yandong Lin 2021-08-10 video: rockchip: mpp: workaround patch for rv1126 iommu issue [ 0.165140] mpp_service mpp-srv: probe start [ 0.166178] iommu: Adding device ffb80000.rkvdec to group 3 [ 0.166240] mpp_rkvdec ffb80000.rkvdec: Linked as a consumer to ffb80480.iommu [ 0.166489] mpp_rkvdec ffb80000.rkvdec: probing start [ 0.167195] mpp_rkvdec ffb80000.rkvdec: shared_niu_a is not found! [ 0.167233] rkvdec_init:1190: No niu aclk reset resource define [ 0.167264] mpp_rkvdec ffb80000.rkvdec: shared_niu_h is not found! [ 0.167288] rkvdec_init:1193: No niu hclk reset resource define [ 0.167607] mpp_rkvdec ffb80000.rkvdec: probing finish [ 0.168461] iommu: Adding device ffbb0000.rkvenc to group 5 [ 0.168528] mpp_rkvenc ffbb0000.rkvenc: Linked as a consumer to ffbb0f00.iommu [ 0.168860] mpp_rkvenc ffbb0000.rkvenc: probing start [ 0.169512] mpp_rkvenc ffbb0000.rkvvenc regulator not ready, retry [ 0.169549] rkvenc_init:1202 devfreq [ 0.170814] iommu: Adding device ffb90400.vdpu to g] mpp_vdpu2 ffb90400.vdpu: Linked as a consumer to ffb90800.iommp_vdpu2 ffb90400.vdpu: probe device [ 0.171574] mpp_vdpu2 ffgroup->rw_sem_on=0 [ 0.171631] mpp_vdpu2 ffb90400.vdpu: rese 0.171905] mpp_vdpu2 ffb90400.vdpu: probing finish [ 0.17device ffb90000.vepu to group 4 [ 0.172646] mpp_vepu2 ffb900onsumer to ffb90800.iommu [ 0.172783] mpp_vepu2 ffb90000.vep 0.173363] mpp_vepu2 ffb90000.vepu: reset_group->rw_sem_on=0 [epu2 ffb90000.vepu: reset_group->rw_sem_on=0 [ 0.173680] mppprobing finish [ 0.174264] iommu: Adding device ffb20000.iep.174323] mpp-iep2 ffb20000.iep: Linked as a consumer to ffb208002] mpp-iep2 ffb20000.iep: probe device [ 0.175107] mpp-iep2 roi buffer failed [ 0.175338] mpp-iep2 ffb20000.iep: probin632] mpp_service mpp-srv: probe success [ 0.180927] dma-pl33oller: Loaded driver for PL330 DMAC-241330 [ 0.180972] dma-pontroller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-ockchip-system-monitor rockchip-system-monitor: system monitor p[ 0.184153] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled [ 0.185090] ff410000.serial: ttyS1 at MMIO 0xff410000 (irq = 31, base_baud = 1500000) is a 16550A [ 0.185908] ff560000.serial: ttyS0 at MMIO 0xff560000 (irq = 34, base_baud = 1500000) is a 16550A [ 0.186768] ff580000.serial: ttyS3 at MMIO 0xff580000 (irq = 35, base_baud = 1500000) is a 16550A [ 0.187512] ff590000.serial: ttyS4 at MMIO 0xff590000 (irq = 36, base_baud = 1500000) is a 16550A [ 0.189686] random: fast init done [ 0.190089] random: crng init done [ 0.190715] iommu: Adding device ffb00000.vop to group 0 [ 0.190784] rockchip-vop ffb00000.vop: Linked as a consumer to ffb00f00.iommu [ 0.194430] rockchip-drm display-subsystem: Linked as a consumer to ffb00000.vop [ 0.196905] rockchip-drm display-subsystem: devfreq is not set [ 0.197439] rockchip-drm display-subsystem: bound ffb00000.vop (ops 0xb0a3e140) [ 0.197467] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 0.197482] [drm] No driver support for vblank timestamp query. [ 0.197638] rockchip-drm display-subsystem: failed to parse loader memory [ 0.198532] [drm] Initialized rockchip 2.0.0 20140818 for display-subsystem on minor 0 [ 0.203558] panel-simple panel@0: panel@0 supply power not found, using dummy regulator [ 0.203701] panel-simple panel@0: Linked as a consumer to regulator.0 [ 0.203753] panel-simple panel@0: panel@0 supply vsp not found, using dummy regulator [ 0.203877] panel-simple panel@0: panel@0 supply vsn not found, using dummy regulator [ 0.212944] loop: module loaded [ 0.213737] zram: Added device: zram0 [ 0.216371] libphy: Fixed MDIO Bus: probed [ 0.216472] tun: Universal TUN/TAP device driver, 1.6 [ 0.218062] PPP generic driver version 2.4.2 [ 0.218331] PPP BSD Compression module registered [ 0.218352] PPP Deflate Compression module registered [ 0.218401] PPP MPPE Compression module registered [ 0.218427] NET: Registered protocol family 24 [ 0.218550] usbcore: registered new interface driver r8152 [ 0.218663] usbcore: registered new interface driver asix [ 0.218755] usbcore: registered new interface driver ax88179_178a [ 0.218831] usbcore: registered new interface driver cdc_ether [ 0.218897] usbcore: registered new interface driver net1080 [ 0.218973] usbcore: registered new interface driver cdc_subset [ 0.219045] usbcore: registered new interface driver zaurus [ 0.219157] usbcore: registered new interface driver cdc_ncm [ 0.219235] usbcore: registered new interface driver qmi_wwan [ 0.221128] dwc3 ffd00000.dwc3: Failed to get clk 'ref': -2 [ 0.227781] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.227837] ehci-platform: EHCI generic platform driver [ 0.231517] ehci-platform ffe00000.usb: EHCI Host Controller [ 0.231605] ehci-platform ffe00000.usb: new USB bus registered, assigned bus number 1 [ 0.231819] ehci-platform ffe00000.usb: irq 68, io mem 0xffe00000 [ 0.243073] ehci-platform ffe00000.usb: USB 2.0 started, EHCI 1.00 [ 0.243403] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 [ 0.243441] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.243468] usb usb1: Product: EHCI Host Controller [ 0.243494] usb usb1: Manufacturer: Linux 4.19.111 ehci_hcd [ 0.243520] usb usb1: SerialNumber: ffe00000.usb [ 0.244420] hub 1-0:1.0: USB hub found [ 0.244502] hub 1-0:1.0: 1 port detected [ 0.245295] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.245352] ohci-platform: OHCI generic platform driver [ 0.246028] ohci-platform ffe10000.usb: Generic Platform OHCI controller [ 0.246095] ohci-platform ffe10000.usb: new USB bus registered, assigned bus number 2 [ 0.246306] ohci-platform ffe10000.usb: irq 69, io mem 0xffe10000 [ 0.307358] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 [ 0.307416] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.307437] usb usb2: Product: Generic Platform OHCI controller [ 0.307496] usb usb2: Manufacturer: Linux 4.19.111 ohci_hcd [ 0.307515] usb usb2: SerialNumber: ffe10000.usb [ 0.308435] hub 2-0:1.0: USB hub found [ 0.308521] hub 2-0:1.0: 1 port detected [ 0.310373] usbcore: registered new interface driver cdc_wdm [ 0.310542] usbcore: registered new interface driver usb-storage [ 0.310713] usbcore: registered new interface driver option [ 0.310778] usbserial: USB Serial support registered for GSM modem (1-port) [ 0.311957] i2c /dev entries driver [ 0.314080] rk808 0-0020: chip id: 0x8090 [ 0.314204] rk808 0-0020: No cache defaults, reading back from HW [ 0.320644] rk808 0-0020: source: on=0x40, off=0x00 [ 0.320700] rk808 0-0020: support dcdc3 fb mode:-22, -1329981084 [ 0.320729] rk808 0-0020: support pmic reset mode:0,0 [ 0.325253] rk808-regulator rk808-regulator: there is no dvs0 gpio [ 0.325383] rk808-regulator rk808-regulator: there is no dvs1 gpio [ 0.325492] DCDC_REG1: supplied by vcc5v0_sys [ 0.326226] DCDC_REG2: supplied by vcc5v0_sys [ 0.326968] DCDC_REG3: supplied by vcc5v0_sys [ 0.327475] DCDC_REG4: supplied by vcc5v0_sys [ 0.327996] DCDC_REG5: supplied by vcc5v0_sys [ 0.328647] LDO_REG1: supplied by vcc_buck5 [ 0.329274] LDO_REG2: supplied by vcc_buck5 [ 0.329812] LDO_REG3: supplied by vcc_buck5 [ 0.330349] LDO_REG4: supplied by vcc_buck5 [ 0.330879] LDO_REG5: supplied by vcc_buck5 [ 0.331376] LDO_REG6: supplied by vcc_buck5 [ 0.331465] vcc_dvdd: Bringing 1100000uV into 1200000-1200000uV [ 0.332100] LDO_REG7: supplied by vcc5v0_sys [ 0.332636] LDO_REG8: supplied by vcc5v0_sys [ 0.333342] LDO_REG9: supplied by vcc5v0_sys [ 0.334011] SWITCH_REG1: supplied by vcc5v0_sys [ 0.334458] SWITCH_REG2: supplied by vcc3v3_sys [ 0.336898] input: rk805 pwrkey as /devices/platform/ff3f0000.i2c/i2c-0/0-0020/rk805-pwrkey/input/input0 [ 0.340057] rk808-rtc rk808-rtc: registered as rtc0 [ 0.340685] rk808-rtc rk808-rtc: setting system clock to 2017-08-04 09:00:02 UTC (1501837202) [ 0.343753] pca953x 1-0020: 1-0020 supply vcc not found, using dummy regulator [ 0.343884] pca953x 1-0020: Linked as a consumer to regulator.0 [ 0.790214] Freeing initrd memory: 8948K [ 1.359782] rk3x-i2c ff510000.i2c: timeout, ipd: 0x90, state: 1 [ 1.359840] pca953x 1-0020: failed reading register [ 1.359953] pca953x 1-0020: Dropping the link to regulator.0 [ 1.360034] pca953x: probe of 1-0020 failed with error -110 [ 1.439710] phy phy-ff4c0000.usb2-phy.1: charger = USB_SDP_CHARGER [ 2.479715] rk3x-i2c ff510000.i2c: timeout, ipd: 0x90, state: 1 [ 3.493071] rk3x-i2c ff510000.i2c: timeout, ipd: 0x90, state: 1 [ 4.506398] rk3x-i2c ff510000.i2c: timeout, ipd: 0x90, state: 1 [ 4.506493] himax_tp: probe of 1-0048 failed with error -9 [ 4.506765] rockchip-pinctrl pinctrl: pin gpio3-0 already requested by ff580000.serial; cannot claim for ff530000.i2c [ 4.506801] rockchip-pinctrl pinctrl: pin-96 (ff530000.i2c) status -22 [ 4.506832] rockchip-pinctrl pinctrl: could not request pin 96 (gpio3-0) from group i2c4m0-xfer on device rockchip-pinctrl [ 4.506858] rk3x-i2c ff530000.i2c: Error applying setting, reverse things back [ 4.506898] rk3x-i2c: probe of ff530000.i2c failed with error -22 [ 4.507888] ircut cam_ircut: driver version: 00.01.00 [ 4.508148] ircut cam_ircut: failed get pulse-width,use dafult value 100 [ 4.508227] ircut cam_ircut: Failed to get ircut-open-gpios [ 4.508300] ircut cam_ircut: Failed to get ircut-close-gpios [ 4.508428] ircut cam_ircut: probe successful! [ 4.509302] rockchip-mipi-csi2: probe success, v4l2_dev:(null)! [ 4.510779] rkcifhw ffae0000.rkcif: no iommu attached, using non-iommu buffers [ 4.510834] r0000.rkcif: assigned reserved memory node isp [ 4.510979] rk driver version: v00.01.0a [ 4.511078] rkcif rkcif_dvp: atta[ 4.511110] rkcif rkcif_dvp: rkcif wait line 0 [ 4.512258bdev_notifier: no subdev be found! [ 4.512291] rkcif_dvp: Fadev notifier(-19) [ 4.513423] rkcif rkcif_dvp: detach to cif3552] rkcif rkcif_mipi_lvds: rkcif driver version: v00.01.0a [ kcif_mipi_lvds: attach to cif hw node [ 4.513688] rkcif rkciwait line 0 [ 4.514697] rkcif rkcif_mipi_lvds: Entity type fipi-csi2 was not initialized! [ 4.514724] rockchip-mipi-csi2subdev [ 4.517197] rkisp_hw ffb50000.rkisp: is_thunderboot: kisp_hw ffb50000.rkisp: Missing rockchip,grf property [ 4.510000.rkisp: iommu is disabled, using non-iommu buffers [ 4.50000.rkisp: assigned reserved memory node isp [ 4.517953] rksp driver version: v01.06.02 [ 4.518196] rkisp rkisp-vir0: Nrboot specified [ 4.518451] rkisp rkisp-vir0: Entity type foubdev was not initialized! [ 4.518498] rkisp rkisp-vir0: Entrkisp-csi-subdev was not initialized! [ 4.518531] rkisp rkise for entity rkisp-bridge-ispp was not initialized! [ 4.5222vice ffb60000.rkispp to group 2 [ 4.522301] rkispp_hw ffb600consumer to ffb60e00.iommu [ 4.522715] rkispp_hw ffb60000.rk@0fps [ 4.522767] rkispp_hw ffb60000.rkispp: can't request rmem 0xffb60000-0xffb7ffff] [ 4.523070] rkispp_hw ffb60000.rkcru reset [ 4.523376] rkispp rkispp-vir0: rkispp driver vers4.525596] rkispp rkispp-vir2: rkispp driver version: v01.06.02 e: registered new interface driver uvcvideo [ 4.528299] USB 1) [ 4.528821] rockchip-iodomain fe020000.syscon:io-domains: fe020000.syscon:io-domains: vccio2(3300000 uV) supplied by vcci fe020000.syscon:io-domains: Linked as a consumer to regulator.1chip-iodomain fe020000.syscon:io-domains: vccio3(1800000 uV) sup4.529250] rockchip-iodomain fe020000.syscon:io-domains: vccio4(1 vcc_1v8 [ 4.529390] rockchip-iodomain fe020000.syscon:io-dosumer to regulator.22 [ 4.529451] rockchip-iodomain fe020000io5(3300000 uV) supplied by vcc_3v3 [ 4.529621] rockchip-iod:io-domains: vccio6(3300000 uV) supplied by vcc_3v3 [ 4.5298n fe020000.syscon:io-domains: vccio7(1800000 uV) supplied by vccockchip-iodomain fe020000.syscon:io-domains: Linked as a consume 4.529999] rockchip-iodomain fe020000.syscon:io-domains: pmuio0by vcc1v8_pmu [ 4.530148] rockchip-iodomain fe020000.syscon: a consumer to regulator.10 [ 4.530192] rockchip-iodomain feins: pmuio1(3300000 uV) supplied by vcc3v3_sys [ 4.533579] r0000.tsadc: tsadc trimmed value = -7 [ 4.533991] rockchip-th tsadc is probed successfully! [ 4.534480] rockchip-thermal trimmed value = -4 [ 4.534743] rockchip-thermal ff5f8000.tsccessfully! [ 4.535742] Bluetooth: HCI UART driver ver 2.3 ooth: HCI UART protocol H4 registered [ 4.536114] cpu cpu0: pu cpu0: leakage=1.500 [ 4.536385] cpu cpu0: Linked as a con[ 4.548070] cpu cpu0: temp=27800, pvtm=100744 (100344 + 400) [ 4.548187] cpu cpu0: pvtm-volt-sel=1 [ 4.548294] cpu cpu0: Dropping the link to regulator.8 [ 4.548363] cpu cpu0: bin-scale=5 [ 4.548747] cpu cpu0: Linked as a consumer to regulator.8 [ 4.548838] cpu cpu0: Dropping the link to regulator.8 [ 4.549079] cpu cpu0: Linked as a consumer to regulator.8 [ 4.550390] cpu cpu0: avs=0 [ 4.550881] cpu cpu0: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0 h_table=0 [ 4.550932] cpu cpu0: failed to read out thermal zone (-22) [ 4.551773] cpu cpu0: failed to find power_model node [ 4.551853] cpuidle: enable-method property 'psci' found operations [ 4.551953] cpuidle: enable-method property 'psci' found operations [ 4.552031] cpuidle: enable-method property 'psci' found operations [ 4.552096] cpuidle: enable-method property 'psci' found operations [ 4.552716] Synopsys Designware Multimedia Card Interface Driver [ 4.553399] dwmmc_rockchip ffc50000.dwmmc: IDMAC supports 32-bit address mode. [ 4.553448] dp ffc50000.dwmmc: Using internal DMA controller. [ 4.553467]0000.dwmmc: Version ID is 270a [ 4.553523] dwmmc_rockchip ffntroller at irq 63,32 bit host data width,256 deep fifo [ 4.: card is non-removable. [ 4.566686] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) [ 4.581310] dwmmc_rockchip ffc60000.dwmmc: IDMAC supports 32-bit address mode. [ 4.581455] dwmmc_rockchip ffc60000.dwmmc: Using internal DMA controller. [ 4.581504] dwmmc_rockchip ffc60000.dwmmc: Version ID is 270a [ 4.581663] dwmmc_rockchip ffc60000.dwmmc: DW MMC controller at irq 64,32 bit host data width,256 deep fifo [ 4.581983] dwmmc_rockchip ffc60000.dwmmc: Linked as a consumer to regulator.20 [ 4.582212] dwmmc_rockchip ffc60000.dwmmc: Linked as a consumer to regulator.19 [ 4.596069] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) [ 4.610767] dwmmc_rockchip ffc70000.dwmmc: IDMAC supports 32-bit address mode. [ 4.610900] dwmmc_rockchip ffc70000.dwmmc: Using internal DMA controller. [ 4.610943] dwmmc_rockchip ffc70000.dwmmc: Version ID is 270a [ 4.611101] dwmmc_rockchip ffc70000.dwmmc: DW MMC controller at irq 65,32 bit host data width,256 deep fifo [ 4.611520] dwmmc_rockchip ffc70000.dwmmc: allocated mmc-pwrseq [ 4.611568] mmc_host mmc1: card is non-removable. [ 4.617881] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 200000000Hz, actual 198000000HZ div = 0) [ 4.617951] dwmmc_rockchip ffc50000.dwmmc: Successfully tuned phase to 90 [ 4.618619] mmc0: new HS200 MMC card at address 0001 [ 4.620977] mmcblk0: mmc0:0001 8GTF4R 7.28 GiB [ 4.622061] mmcblk0boot0: mmc0:0001 8GTF4R partition 1 4.00 MiB [ 4.623124] mmcblk0boot1: mmc0:0001 8GTF4R partition 2 4.00 MiB [ 4.623884] mmcblk0rpmb: mmc0:0001 8GTF4R partition 3 512 KiB, chardev (241:0) [ 4.624613] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) [ 4.635344] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 [ 4.638548] usbcore: registered new interface driver usbkbd [ 4.638696] usbcore: registered new interface driver usbmouse [ 4.641560] rockchip-saradc ff5e0000.saradc: Linked as a consumer to regulator.15 [ 4.642486] rksfc_base v1.1 2016-01-08 [ 4.643148] rksfc ffc90000.sfc: rksfc_probe clk rate = 79200000 [ 4.643264] rkflash_dev_init enter [ 4.643298] sfc nor id: 0 0 0 [ 4.643413] rkflash[1] is invalid [ 4.643421] rkflash_dev_init enter [ 4.643463] sfc_nand id: 0 0 0 [ 4.643474] rkflash[2] is invalid [ 4.650756] rk817-codec rk817-codec: DMA mask not set [ 4.650922] rk817_codec_parse_dt_property: rk809 have no io-channels defined [ 4.654298] NET: Registered protocol family 17 [ 4.654370] NET: Registered protocol family 15 [ 4.654926] Bluetooth: RFCOMM TTY layer initialized [ 4.654977] Bluetooth: RFCOMM socket layer initialized [ 4.655014] Bluetooth: RFCOMM ver 1.11 [ 4.655032] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 4.655047] Bluetooth: HIDP socket layer initialized [ 4.655058] [BT_RFKILL]: Enter rfkill_rk_init [ 4.655067] [WLAN_RFKILL]: Enter rfkill_wlan_init [ 4.655375] [WLAN_RFKILL]: Enter rfkill_wlan_probe [ 4.655421] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6236 [ 4.655434] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control. [ 4.655444] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio. [ 4.655503] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,host_wake_irq = 8, flags = 0. [ 4.655537] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio [ 4.655548] [WLAN_RFKILL]: Exit rfkill_wlan_probe [ 4.655883] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 48. [ 4.655911] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,power_gpio = 7. KILL]: bluetooth_platdata_parse_dt: clk_get failed!!!.T,wake_host_irq = 5. [ 4.6quest irq for bt wakeup host [ 4.656109] [BT_RFKILL]: ** dis [BT_RFKILL]: bt shut off power [ 4.656259] [BT_RFKILL]: bt_tered. [ 4.657249] flash vendor_init_thread! [ 4.657282]170308 ret = -1 [ 4.658292] Registering SWP/SWPB emulation h] Loading compiled-in X.509 certificates [ 4.660736] rga2: Dully ver:3.2.56726 [ 4.661060] rga2: Module initialized. [ ing unknown CIS tuple 0x80 (2 bytes) [ 4.669351] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 4.671224] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 4.675078] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 4.679762] mmc1: queuing unknown CIS tuple 0x81 (9 bytes) [ 4.685611] mpp_rkvenc ffbb0000.rkvenc: probing start [ 4.686521] mpp_rkvenc ffbb0000.rkvenc: Linked as a consumer to regulator.7 [ 4.686620] mpp_rkvenc ffbb0000.rkvenc: bin=0 [ 4.686659] mpp_rkvenc ffbb0000.rkvenc: leakage=1.375 [ 4.686749] mpp_rkvenc ffbb0000.rkvenc: Failed to get pvtm [ 4.686782] mpp_rkvenc ffbb0000.rkvenc: bin-scale=37 [ 4.687178] mpp_rkvenc ffbb0000.rkvenc: avs=0 [ 4.687522] mpp_rkvenc ffbb0000.rkvenc: failed to find power_model node [ 4.687552] mpp_rkvenc ffbb0000.rkvenc: failed to initialize power model [ 4.687756] mpp_rkvenc ffbb0000.rkvenc: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0 h_table=0 [ 4.687797] mpp_rkvenc ffbb0000.rkvenc: failed to read out thermal zone (-22) [ 4.688829] mpp_rkvenc ffbb0000.rkvenc: probing finish [ 4.689305] input: adc-keys as /devices/platform/adc-keys/input/input1 [ 4.692745] asoc-simple-card rk809-sound: rk817-hifi <-> ff800000.i2s mapping ok [ 4.692785] asoc-simple-card rk809-sound: ASoC: no source widget found for MICBIAS1 [ 4.692799] asoc-simple-card rk809-sound: ASoC: Failed to add route MICBIAS1 -> direct -> Mic Jack [ 4.692801] vendor storage:20190527 ret = 0 [ 4.692821] asoc-simple-card rk809-sound: ASoC: no sink widget found for IN1P [ 4.692833] asoc-simple-card rk809-sound: ASoC: Failed to add route Mic Jack -> direct -> IN1P [ 2845] asoc-simple-card rk809-sound: ASoC: no source widget found2857] asoc-simple-card rk809-sound: ASoC: Failed to add route HPhone Jack [ 4.692868] asoc-simple-card rk809-sound: ASoC: noor HPOR [ 4.692880] asoc-simple-card rk809-sound: ASoC: Fail -> direct -> Headphone Jack [ 4.694010] input: rockchip,rk8ck as /devices/platform/rk809-sound/sound/card0/input2 [ 4.6 in Dongle Host Driver, version 1.579.77.41.22 (r-20191105-2)(20395] ======== dhd_wlan_init_plat_data ======== [ 4.696407] [hip_wifi_get_oob_irq: Enter [ 4.696468] dhd_wlan_init_gpio: 109, oob_irq_flags=0x414 [ 4.696480] dhd_wlan_init_gpio: WL_90] dhd_wifi_platform_load: Enter [ 4.696502] Power-up adaptr' [ 4.696553] wifi_platform_set_power = 1 [ 4.696566] =N(-1) HIGH! ======== [ 4.696577] [WLAN_RFKILL]: rockchip_wif96589] [WLAN_RFKILL]: wifi turn on power [GPIO-1-0] [ 4.6966[ 4.696704] ret=0 [ 4.696744] rkcif rkcif_mipi_lvds: clea1 [ 4.696760] rockchip-mipi-dphy-rx: No link between dphy an65] rockchip-mipi-dphy-rx: No link between dphy and sensor [ ds: Async subdev notifier completed [ 4.698252] cfg80211: Lo certificates for regulatory database [ 4.708270] cfg80211: forshee: 00b28ddf47aef9cea7' [ 4.708432] platform regulatory for regulatory.db failed with error -2 [ 4.708455] cfg80211atory.db [ 4.709266] rkisp rkisp-vir0: clear unready subdev 5] rockchip-mipi-dphy-rx: No link between dphy and sensor [ ipi-dphy-rx: No link between dphy and sensor [ 4.709835] rkita type [ 4.709845] rkisp0: update sensor failed [ 4.710ffc50000.dwmmc: Successfully tuned phase to 180 [ 4.710695] 00.dwmmc: Successfully tuned phase to 90 [ 4.711098] ret 102 ALSA device list: [ 4.711295] #0: rockchip,rk809-codec [Loopback 1 [ 4.712131] Freeing unused kernel memory: 1024K init as init process Loading, please wait... Couldn't get a file descriptor referring to the console [ 4.768660] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.770431] mmc1: new high speed SDIO card at address 0001 starting version 237 [ 5.003136] wifi_platform_bus_enumerate device present 1 [ 5.003168] ======== Card detection to detect SDIO card! ======== [ 5.003176] mmc1:mmc host rescan start! [ 5.019462] bcmsdh_register: register client driver [ 5.019824] bcmsdh_sdmmc_probe: Enter num=1 [ 5.020202] bcmsdh_sdmmc_probe: Enter num=2 [ 5.020225] bus num (host idx)=1, slot num (rca)=1 [ 5.020233] found adapter info 'DHD generic adapter' [ 5.020293] sdioh_attach: set sd_f2_blocksize 256 [ 5.020352] sdioh_attach: sd clock rate = 0 [ 5.020669] dhdsdio_probe : no mutex held. set lock [ 5.020794] F1 signature read @0x18000000=0x1541a9a6 [ 5.024858] F1 signature OK, socitype:0x1 chip:0xa9a6 rev:0x1 pkg:0x4 [ 5.026002] DHD: dongle ram size is set to 524288(orig 524288) at 0x0 [ 5.026224] [dhd] dhd_conf_set_chiprev : chip=0xa9a6, chiprev=1 [ 5.026617] [dhd] CFG80211-ERROR) wl_setup_wiphy : Registering Vendor80211 [ 5.027117] [dhd] CFG80211-ERROR) wl_setup_wiphy : SAE support [ 5.027624] [dhd] CFG80211-ERROR) wl_init_prof : wl_init_prof: No profile [ 5.029068] dhd_attach(): thread:dhd_watchdog_thread:7b started [ 5.029272] dhd_attach(): thread:dhd_dpc:7d started [ 5.035934] dhd_attach(): thread:dhd_rxf:7e started [ 5.035971] dhd_deferred_work_init: work queue initialized [ 5.035982] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 2 [ 5.036027] dhd_bus_set_default_min_res_mask: Unhandled chip id [ 5.036996] sdioh_cis_read: func_cis_ptr[0]=0x1070 [ 5.048839] Dongle Host Driver, version 1.579.77.41.22 (r-20191105-2)(20191120-1) [ 5.049363] Register interface [wlan0] MAC: b8:13:32:30:d9:70 [ 5.049363] [ 5.049434] dhd_tcpack_suppress_set: TCP ACK Suppress mode 2 -> mode 0 [ 5.049451] dhd_wl_ioctl: returning as busstate=0 [ 5.049459] dhd_dbg_detach_pkt_monitor, 2204 [ 5.049467] dhd_bus_devreset: == Power OFF == [ 5.050335] bcmsdh_oob_intr_unregister: Enter [ 5.050352] bcmsdh_oob_intr_unregister: irq is not registered [ 5.050365] dhd_txglom_enable: enable 0 [ 5.050375] dhd_bus_devreset: WLAN OFF DONE [ 5.050437] wifi_platform_set_power = 0 [ 5.050448] ======== PULL WL_REG_ON(-1) LOW! ======== [ 5.050456] [WLAN_RFKILL]: rockchip_wifi_power: 0 [ 5.050473] [WLAN_RFKILL]: wifi shut off power [GPIO-1-1] [ 5.050482] dhdsdio_probe : the lock is released. [ 5.050812] dhd_module_init: Exit err=0 /scripts/init-top/console_setup: line 134: can't create /dev/tty1: No such device or address /scripts/init-top/console_setup: line 1: can't open /dev/tty1: No such device or address /scripts/init-top/console_setup: line 1: can't create /dev/tty2: No such device or address /scripts/init-top/console_setup: line 1: can't open /dev/tty2: No such device or address /scripts/init-top/console_setup: line 1: can't create /dev/tty3: No such device or address /scripts/init-top/console_setup: line 1: can't open /dev/tty3: No such device or address /scripts/init-top/console_setup: line 1: can't create /dev/tty4: No such device or address /scripts/init-top/console_setup: line 1: can't open /dev/tty4: No such device or address /scripts/init-top/console_setup: line 1: can't create /dev/tty5: No such device or address /scripts/init-top/console_setup: line 1: can't open /dev/tty5: No such device or address /scripts/init-top/console_setup: line 1: can't create /dev/tty6: No such device or address /scripts/init-top/console_setup: line 1: can't open /dev/tty6: No such device or address Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Warning: fsck not present, so skipping root file system [ 7.241421] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... Warning: overlayroot: configuring overlayroot with driver=overlay mode=device opts='dev=PARTLABEL=userdata,fstype=ext4,mkfs=1' per kernel cmdline [ 7.377619] EXT4-fs (mmcblk0p8): warning: mounting unchecked fs, running e2fsck is recommended [ 7.400474] EXT4-fs (mmcblk0p8): mounted filesystem without journal. Opts: (null) [[: missing ]] ln: /root/var/lib/docker: File exists Success: overlayroot: configured root with 'device:dev=PARTLABEL=userdata,fstype=ext4,mkfs=1' using overlay per kernel cmdline Warning: Something odd, no /lib/modules/4.19.111 in initramfs. done. [ 7.787816] systemd[1]: System time before build time, advancing clock. [ 7.796570] systemd[1]: Failed to lookup module alias 'autofs4': Function not implemented [ 7.814704] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid) [ 7.815725] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 10 (buster)! [ 7.819127] systemd[1]: Set hostname to <firefly>. [ 7.987238] systemd[1]: File /lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 7.987309] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 8.294856] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 8.295854] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 8.297205] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 8.298851] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ OK ] Reached target Remote File Systems. [ OK ] Listening on initctl Compatibility Named Pipe. [ 8.299456] systemd[1]: Reached target Remote File Systems. [ OK ] Listening on Syslog Socket. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ OK ] Listening on udev Control Socket. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ OK ] Reached target Paths. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. [ OK ] Listening on Journal Socket. Starting udev Coldplug all Devices... Starting Remount Root and Kernel File Systems... Mounting Kernel Debug File System... Starting Load Kernel Modules... [ OK ] Created slice system-serial\x2dgetty.slice. Starting Journal Service... [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Mounted Kernel Debug File System. Starting Create System Users... Starting Load/Save Random Seed... [ OK ] Started Load Kernel Modules. Mounting Kernel Configuration File System... Starting Apply Kernel Variables... [ OK ] Mounted Kernel Configuration File System. [ OK ] Started Apply Kernel Variables. [ OK ] Started Create System Users. [ OK ] Started Load/Save Random Seed. Starting Create Static Device Nodes in /dev... [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. [ OK ] Started udev Kernel Device Manager. [ OK ] Started Journal Service. Starting Flush Journal to Persistent Storage... [ OK ] Started udev Coldplug all Devices. Starting Helper to synchronize boot up for ifupdown... [ OK ] Started Helper to synchronize boot up for ifupdown. [ 8.719100] systemd-journald[407]: Received request to flush runtime journal from PID 1 Starting Raise network interfaces... [ OK ] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Created slice system-systemd\x2dbacklight.slice. Starting Load/Save Screen …ness of backlight:backlight... [ OK ] Started Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Load/Save Screen B…htness of backlight:backlight. [ OK ] Found device /dev/ttyFIQ0. [ 9.157921] rockchip-mipi-dphy-rx: No link between dphy and sensor [ 9.169446] rockchip-mipi-dphy-rx: No link between dphy and sensor [ 9.171945] rockchip-mipi-dphy-rx: No link between dphy and sensor [ OK ] Started Network Time Synchronization. [ 9.180079] rockchip-mipi-dphy-rx: No link between dphy and sensor [ OK ] Started Update UTMP about System Boot/Shutdown. [ 9.216731] rockchip-mipi-dphy-rx: No link between dphy and sensor [ OK ] Started Raise network interfaces. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. [ OK ] Reached target System Time Synchronized. [ OK ] Reached target System Initialization. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Started Daily apt download activities. [ OK ] Started Daily man-db regeneration. [ OK ] Started Daily rotation of log files. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Basic System. [ OK ] Started Manage Sound Card State (restore and store). [ OK ] Started Regular background program processing daemon. Starting Restore /etc/reso… the ppp link was shut down... Starting System Logging Service... Starting Npu Init... Starting Modem Manager... Starting Adbd for linux... Starting Login Service... Starting Save/Restore Sound Card State... [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Reached target Timers. [ OK ] Started D-Bus System Message Bus. Starting WPA supplicant... [ 9.940267] galcore: loading out-of-tree module taints kernel. [ 9.948511] galcore: npu init. [ 9.957674] galcore: start npu probe. Starting Network Manager... [ 9.958392] galcore ffbc0000.npu: Linked as a consumer to regulator.7 [ OK ] Started System Logging Service. [ 9.967398] npu: platform_get_irq irq = 67 [ 9.967473] npu: platform_get_resource registerMemBase = ffbc0000, registerMemSize = 4000 [ 9.967507] Galcore version 6.4.6.5.351518 [ 9.967534] Galcore options: [ 9.967562] irqLine = 67 [ 9.967580] registerMemBase = 0xFFBC0000 [ 9.967597] registerMemSize = 0x00004000 [ 9.967616] contiguousSize = 0x00400000 [ 9.967632] contiguousBase = 0x0 [ 9.967649] externalSize = 0x00000000 [ 9.967687] externalBase = 0x0 [ 9.967707] exclusiveSize = 0x00000000 [ 9.967732] exclusiveBase = 0x0 [ 9.967751] bankSize = 0x00000000 [ 9.967780] fastClear = -1 [ 9.967800] compression = 15 [ 9.967817] powerManagement = 1 [ 9.967834] baseAddress = 0x00000000 [ 9.967862] physSize = 0x00000000 [ 9.967883] recovery = 1 [ 9.967938] stuckDump = 0 [ 9.967962] GPU smallBatch = 1 [ 9.967986] allMapInOne = 1 [ 9.968015] enableNN = 0xff [ 9.968045] userClusterMasks = [ 9.968048] ff, [ 9.968072] ff, [ 9.968089] ff, [ 9.968105] ff, [ 9.968122] ff, [ 9.968177] ff, [ 9.968200] ff, [ 9.968229] ff, [ 9.968249] [ 9.968272] irqs = [ 9.968274] 67, [ 9.968290] -1, [ 9.968307] -1, 9.968324] -1, [ 9.968339] -1, [ 9.968355] -1, [ 9.968413] -1, [ 9.968445] -1, [ 9.968470] -1, [ Started -1, [ 9.968500] [ 9mRestore pp l.968524] registerBases = 0, ink was shut down. [ 9.968549] 0x00000000, [ 9.968566] 0x00000000, [000, [ 9.968601] 0x00000000, 00, 9.968645] 0x00000000, [ 9.968723] 0x00000000, [ 9.968760] 0x00000000, 0000, [ 9.968829] 0x00000000, [ 9.968886] [ 9.968 = [ 9.968929] 0x00004000, [ 9.968955] 0x00000000, 0000, [ 9.969016] 0x00000000, [ 9.969051] 0x00000000, 000000, [ 9.969163] 0x00000000, [ 9.969199] 0x00000000x00000000, [ 9.969270] 0x00000000, [ 9.969304] 0x00000[ 9.969399] chipIDs = [ 9.969401] 0xFFFFFFFFFFFFFFF, [ 9.969438] 0xFFFFFFFF, [ 9.969457] 0xFFFFFFFFFFFFFFF, [ 9.969496] 0xFFFFFFFF, [ 9.969527] 0xFFFFFFFFFFFFF, [ 9.969605] 0xFFFFFFFF, [ 9.976594] 0xFFFFFFFFFFFFFF, [ 9.976708] [ 9.976734] core 0 internal sRA735] 0xFFFFFFFFFFFFFFFF, [ 9.976760] 0xFFFFFFFFFFFFFFFF, 9.976802] core 1 internal sRAMBases = [ 9.976803] 0xFFFFF.976822] 0xFFFFFFFFFFFFFFFF, [ 9.976839] [ 9.976861] s = [ 9.976863] 0xFFFFFFFFFFFFFFFF, [ 9.976879] 0xFFFF.976914] [ 9.976938] core 3 internal sRAMBases = [ 9FFFFF, [ 9.976959] 0xFFFFFFFFFFFFFFFF, [ 9.976975] [internal sRAMBases = [ 9.976997] 0xFFFFFFFFFFFFFFFF, [ FFFFFFF, [ 9.977029] [ 9.977049] core 5 internal sRA50] 0xFFFFFFFFFFFFFFFF, [ 9.977066] 0xFFFFFFFFFFFFFFFF, [977104] core 6 internal sRAMBases = [ 9.977106] 0xFFFFFFF OK ] Started 9.977188] mSave/Restore Sound Card State core 7 internal 977190] 0xFFFFFFFFFFFFFFFF, [ 9.977208] 0xFFFFFFFFFFFFFFFF, 9.977249] core 8 internal sRAMBases = [ 9.977251] 0xF[ 9.977271] 0xFFFFFFFFFFFFFFFF, [ 9.977289] [ 9.977l sRAMBases = [ 9.977313] 0xFFFFFFFFFFFFFFFF, [ 9.9773FF, [ 9.977346] [ 9.977384] core 10 internal sRAMBas0xFFFFFFFFFFFFFFFF, [ 9.977402] 0xFFFFFFFFFFFFFFFF, [ 977439] External sRAMBases = [ 9.977441] 0xffffffffffffff 0xffffffffffffffff, [ 9.977472] [ 9.977491] mmuPage.977507] mmuDynamicMap = 1 [ 9.977523] isrPoll 9.977540] Build options: [ 9.977556] gcdGPU_TIMEOUT 7573] gcdGPU_2D_TIMEOUT = 4000 [ 9.977589] gcdINTERRUPT_88736] Galcore Info: ContiguousBase=0x3f956000 ContiguousSize=0x22] Galcore Info: MMU mapped core 0 SRAM[0] hardware virtual addx40000 [ 9.993987] Galcore Info: MMU mapped core 0 SRAM[1] hss=0x440000 size=0x40000 [ 9.999585] galcore ffbc0000.npu: I9.999741] galcore ffbc0000.npu: bin=0 [ 9.999808] galcore ff [ 10.012272] galcore ffbc0000.npu: temp=28900, pvtm=100641 (10.012668] galcore ffbc0000.npu: pvtm-volt-sel=1 [ 10.012743]u: bin-scale=23 [ 10.013996] galcore ffbc0000.npu: avs=0 [ 10.014823] galcore ffbc0000.npu: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0 h_table=0 [ 10.014950] galcore ffbc0000.npu: failed to read out thermal zone (-22) [ 10.015109] galcore ffbc0000.npu: failed to find power_model node [ 10.015180] galcore ffbc0000.npu: failed to initialize power model Starting Load/Save RF Kill Switch Status... [ OK ] Reached target Sound Card. [ OK ] Started Npu Init. [ 10.071062] file system registered [ 10.076223] [BT_RFKILL]: bt shut off power [ OK ] Started Load/Save RF Kill Switch Status. [ OK ] Started WPA supplicant. [ OK ] Started Login Service. [ 10.127026] read descriptors [ 10.127160] read strings Starting Authorization Manager... [ OK ] Started Authorization Manager. [ OK ] Started Network Manager. [ OK ] Reached target Network. Starting Permit User Sessions... Starting OpenBSD Secure Shell server... Starting Hostname Service... [ OK ] Started Permit User Sessions. [ OK ] Started Serial Getty on ttyFIQ0. [ OK ] Reached target Login Prompts. [ OK ] Started Modem Manager. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started Hostname Service. Starting Network Manager Script Dispatcher Service... [ OK ] Started Network Manager Script Dispatcher Service. [ 10.638249] dhd_open: Enter c0d12a61 [ 10.638297] dhd_open : no mutex held. set lock [ 10.638310] [ 10.638310] Dongle Host Driver, version 1.579.77.41.22 (r-20191105-2)(20191120-1) [ 10.638326] [dhd-wlan0] wl_android_wifi_on : in g_wifi_on=0 [ 10.638334] wifi_platform_set_power = 1 [ 10.638343] ======== PULL WL_REG_ON(-1) HIGH! ======== [ 10.638351] [WLAN_RFKILL]: rockchip_wifi_power: 1 [ 10.638365] [WLAN_RFKILL]: wifi turn on power [GPIO-1-0] [ 10.943378] sdio_reset_comm(): [ 10.959190] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) [ 10.976968] mmc_host mmc1: Bus speed (slot 0) = 100000Hz (slot req 100000Hz, actual 100000HZ div = 0) [ 11.038856] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) [ 11.047391] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 11.054476] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 11.067364] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 11.081418] mmc1: queuing unknown CIS tuple 0x81 (9 bytes) [ OK ] Started Adbd for linux. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. [ 11.209918] ttyFIQ ttyFIQ0: tty_port_close_start: tty->count = 1 port count = 2 Debian GNU/Linux 10 firefly ttyFIQ0 firefly login: root (automatic login) [ 11.235729] dwc3 ffd00000.dwc3: device reset Last login: Thu Feb 14 10:12:01 UTC 2019 on ttyFIQ0 Linux firefly 4.19.111 #1 SMP PREEMPT Wed Feb 8 16:52:46 CST 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. [ 11.343580] android_work: sent uevent USB_STATE=CONNECTED [ 11.423969] configfs-gadget gadget: high-speed config #1: b [ 11.424176] android_work: sent uevent USB_STATE=CONFIGURED [ 11.434460] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 11.434590] sdioh_start: set sd_f2_blocksize 256 [ 11.434911] [ 11.434911] [ 11.434911] dhd_bus_devreset: == WLAN ON == [ 11.435065] F1 signature read @0x18000000=0x1541a9a6 [ 11.440991] F1 signature OK, socitype:0x1 chip:0xa9a6 rev:0x1 pkg:0x4 [ 11.442359] DHD: dongle ram size is set to 524288(orig 524288) at 0x0 [ 11.442520] dhd_bus_set_default_min_res_mask: Unhandled chip id [ 11.444292] [dhd] dhd_conf_read_config : Ignore config file /vendor/etc/firmware/config.txt [ 11.444333] [dhd] dhd_conf_set_path_params : Final fw_path=/vendor/etc/firmware/fw_bcm43438a1.bin [ 11.444343] [dhd] dhd_conf_set_path_params : Final nv_path=/vendor/etc/firmware/nvram_ap6212a.txt [ 11.444352] [dhd] dhd_conf_set_path_params : Final clm_path=/vendor/etc/firmware/clm_bcm43438a1.blob [ 11.444367] [dhd] dhd_conf_set_path_params : Final conf_path=/vendor/etc/firmware/config.txt [ 11.445307] dhd_os_open_image: /vendor/etc/firmware/fw_bcm43438a1.bin (414579 bytes) open success [ 11.502902] dhd_os_open_image: /vendor/etc/firmware/nvram_ap6212a.txt (1017 bytes) open success [ 11.503723] NVRAM version: AP6212A_NVRAM_V1.0.2_20191121 [ 11.504378] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded. [ 11.579786] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us) [ 11.579936] bcmsdh_oob_intr_register: HW_OOB irq=109 flags=0x4 [ 11.580266] dhd_get_memdump_info: File [/data/misc/wifi/.memdump.info] doesn't exist [ 11.580305] dhd_get_memdump_info: MEMDUMP ENABLED = 2 [ 11.581328] Disable tdls_auto_op failed. -1 [ 11.581351] dhd_tcpack_suppress_set 352: already set to 0 [ 11.581708] dhd_apply_default_clm: Ignore clm file /vendor/etc/firmware/clm_bcm43438a1.blob [ 11.584344] Firmware up: op_mode=0x0005, MAC=b8:13:32:30:d9:70 [ 11.587510] dhd_preinit_ioctls Set scancache failed -23 [ 11.598564] Driver: 1.579.77.41.22 (r-20191105-2)(20191120-1) [ 11.598564] Firmware: wl0: Jun 13 2018 13:18:38 version 7.45.96.24 (7ffe8b7@shgit) (r) FWID 01-40f9deb0 es7.c5.n4.a3 [ 11.598564] CLM: 7.11.15 (2014-05-26 10:53:55) [ 11.598812] dhd_txglom_enable: enable 1 [ 11.598826] [dhd] dhd_conf_set_txglom_params : txglom_mode=copy [ 11.598836] [dhd] dhd_conf_set_txglom_params : txglomsize=36, deferred_tx_len=0 [ 11.598843] [dhd] dhd_conf_set_txglom_params : txinrx_thres=-1, dhd_txminmax=1 [ 11.598852] [dhd] dhd_conf_set_txglom_params : tx_max_offset=0, txctl_tmo_fix=300 [ 11.598865] [dhd] dhd_conf_get_disable_proptx : fw_proptx=1, disable_proptx=-1 [ 11.600018] dhd_wlfc_hostreorder_init(): successful bdcv2 tlv signaling, 64 [ 11.601921] dhd_pno_init: Support Android Location Service [ 11.629208] [dhd] CFG80211-ERROR) wl_cfg80211_event : Event handler is not created [ 11.631520] rtt_do_get_ioctl: failed to send getbuf proxd iovar (CMD ID : 1), status=-23 [ 11.631561] dhd_rtt_init : FTM is not supported [ 11.631570] dhd_preinit_ioctls: SensorHub diabled 0 [ 11.632500] dhd_preinit_ioctls failed to set ShubHub disable [ 11.634256] dhd_wl_ioctl_get_intiovar: get int iovar wnm_bsstrans_resp failed, ERR -23 [ 11.634271] failed to get wnm_bsstrans_resp [ 11.634891] failed to set WNM capabilities [ 11.635179] [dhd] dhd_conf_set_country : set country CN, revision 0 [ 11.635202] [dhd] CFG80211-ERROR) wl_cfg80211_event : Event handler is not created [ 11.638317] [dhd] dhd_conf_set_country : Country code: CN (CN/0) [ 11.642788] [dhd] CONFIG-ERROR) dhd_conf_set_intiovar : ampdu_mpdu setting failed -29 [ 11.642822] [dhd-wlan0] wl_android_wifi_on : Success [ 11.672421] [dhd] CFG80211-ERROR) __wl_update_wiphybands : error reading vhtmode (-23) [ 11.685040] dhd_open : the lock is released. [ 11.685074] dhd_open: Exit ret=0 [ 11.804629] P2P interface registered [ 11.804677] wl_cfgp2p_add_p2p_disc_if: wdev: 49951420, wdev->net: (null) [ 11.829960] WLC_E_IF: NO_IF set, event Ignored [ 11.831977] P2P interface started DTSI增加内容如下： / { panel@0 { compatible = "simple-panel"; /delete-property/ power-supply; bus-format = <MEDIA_BUS_FMT_RGB888_1X24>; backlight = <&backlight>; enable-gpios = <&gpio0 RK_PD6 GPIO_ACTIVE_HIGH>; pinctrl-0 = <&lcd_ctl>; pinctrl-names = "default"; rgb-mode = "p888"; width-mm = <99>; height-mm = <74>; status = "okay"; display-timings { native-mode = <&HT043t_timing>; HT043t_timing: timing0 { clock-frequency = <9000000>; hactive = <480>; vactive = <272>; hback-porch = <10>; hfront-porch = <10>; vback-porch = <4>; vfront-porch = <4>; hsync-len = <2>; vsync-len = <2>; hsync-active = <0>; vsync-active = <0>; de-active = <0>; pixelclk-active = <0>; }; }; port { panel_in_rgb: endpoint { remote-endpoint = <&rgb_out_panel>; }; }; }; }; &display_subsystem { status = "okay"; }; &rgb { status = "okay"; ports { rgb_out: port@1 { reg = <1>; #address-cells = <1>; #size-cells = <0>; rgb_out_panel: endpoint@0 { reg = <0>; remote-endpoint = <&panel_in_rgb>; }; }; }; }; &route_rgb { status = "okay"; }; &vop { status = "okay"; }; &rgb_in_vop{ status = "okay"; }; |
-
-
350.01 KB, 下载次数: 3, 下载积分: 灯泡 -1 , 经验 -1
LCD
-
-
57.9 KB, 下载次数: 0, 下载积分: 灯泡 -1 , 经验 -1
