开启辅助访问

Firefly开源社区

Firefly开源社区 › 开源主板 › AIO-3288J › 硬件交流› RK3288 自己的板子，发现MASKROM下载IDB失败，复位后出 ...
发表新贴
打印 上一主题 下一主题

RK3288 自己的板子，发现MASKROM下载IDB失败，复位后出现LOADER设备，就变检验固件...

peky2018

31

积分

0

威望

0

贡献

技术小白

积分
31

RK3288 自己的板子，发现MASKROM下载IDB失败，复位后出现LOADER设备，就变检验固件...

发表于 2019-7-23 17:31:53      浏览：10869 | 回复：6        打印      只看该作者   [复制链接] 楼主
RK3288 自己的板子，发现MASKROM下载IDB失败，如图1


复位后出现LOADER设备，如图2 ，，，就变检验固件失败 ，而又可以擦除成功 ，各位路过大神又遇见过的 吗？


附上   MASKROM设备，下载IDB失败；复位后loader设备   的 log


[BEGIN] 2019/7/23 17:21:30

Connection closed.

Disconnected from remote host(新建会话 (3)) at 17:21:37.

Type `help' to learn how to use Xshell prompt.
[c:\~]$

Connecting to COM12...
Connected.

DDR Version 1.00 20160530
In
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Memory OK
Memory OK
OUT
usb boot ver:20160218
ChipType = 8
...FlashInit enter...
FtlMallocOffset = 8040 8000
FtlMallocOffset = 10040 8000
FtlMallocOffset = 11040 1000
FtlMallocOffset = 19040 8000
FtlMallocOffset = 1a040 1000
1:200 0 7f7f05 22
...NandcInit enter...
0:1200 0 7f7f05 22 200
FtlMallocOffset = 23040 9000
gNandcVer = 6
SDC_BusRequest:  CMD=8  SDC_RESP_TIMEOUT 1815
  SDC_BusRequest:  CMD=8  SDC_RESP_TIMEOUT 1815
  SDC_BusRequest:  CMD=8  SDC_RESP_TIMEOUT 1815
  SDC_BusRequest:  CMD=5  SDC_RESP_TIMEOUT 1815
  SDC_BusRequest:  CMD=5  SDC_RESP_TIMEOUT 1815
  SDC_BusRequest:  CMD=5  SDC_RESP_TIMEOUT 1815
  SDC_BusRequest:  CMD=55  SDC_RESP_TIMEOUT 1815
  SDC_BusRequest:  CMD=55  SDC_RESP_TIMEOUT 1815
  SDC_BusRequest:  CMD=55  SDC_RESP_TIMEOUT 1815
mmc Ext_csd, ret=0 ,
Ext[226]=20, bootSize=2000,
                 Ext[215]=1, Ext[214]=d1, Ext[213]=f0, Ext[212]=0,cap =1d1f000 REL=1f
SdmmcInit=2 0
BootCapSize=2000
UserCapSize=1d1f000
FwPartOffset=2000 , 2000
UsbHook 596335
powerOn 597248
DDR Version 1.00 20160530
In
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Memory OK
Memory OK
OUT
DDR Version 1.00 20160530
In
SRX
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
OUT
DDR Version 1.00 20160530
In
SRX
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
OUT


U-Boot 2014.10-RK3288-10 (Mar 18 2019 - 18:00:13)

CPU: rk3288
cpu version = 0
CPU's clock information:
    arm pll = 600000000HZ
    periph pll = 297000000HZ
    ddr pll = 200000000HZ
    codec pll = 384000000HZ
Board:        Rockchip platform Board
DRAM:  Found dram banks: 1
Adding bank:0000000000000000(0000000080000000)
128 MiB
GIC CPU mask = 0x00000001
SdmmcInit = 0 400
SdmmcInit = 2 0
storage init OK!
Using default environment

GetParam
W: Invalid Parameter's tag (0xFFFFFFFF)!
Invalid parameter
No pmic detect.
SecureBootEn = 0, SecureBootLock = 0

#Boot ver: 2019-03-18#2.30
empty serial no.
Writing env to storage...
done
checkKey
vbus = 1
rockusb key pressed.


-------------------------------------------------------------------------------------------------
附上  loader设备 校验固件 失败 的 flog


DR Version 1.00 20160530
In
SRX
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
OUT


U-Boot 2014.10-RK3288-10 (Mar 18 2019 - 18:00:13)

CPU: rk3288
cpu version = 0
CPU's clock information:
    arm pll = 600000000HZ
    periph pll = 297000000HZ
    ddr pll = 200000000HZ
    codec pll = 384000000HZ
Board:        Rockchip platform Board
DRAM:  Found dram banks: 1
Adding bank:0000000000000000(0000000080000000)
128 MiB
GIC CPU mask = 0x00000001
SdmmcInit = 0 400
SdmmcInit = 2 0
storage init OK!
Using default environment

GetParam
W: Invalid Parameter's tag (0xFFFFFFFF)!
Invalid parameter
No pmic detect.
SecureBootEn = 0, SecureBootLock = 0

#Boot ver: 2019-03-18#2.30
empty serial no.
reboot to rockusb.
DDR Version 1.00 20160530
In
SRX
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
OUT


U-Boot 2014.10-RK3288-10 (Mar 18 2019 - 18:00:13)

CPU: rk3288
cpu version = 0
CPU's clock information:
    arm pll = 600000000HZ
    periph pll = 297000000HZ
    ddr pll = 200000000HZ
    codec pll = 384000000HZ
Board:        Rockchip platform Board
DRAM:  Found dram banks: 1
Adding bank:0000000000000000(0000000080000000)
128 MiB
GIC CPU mask = 0x00000001
SdmmcInit = 0 400
SdmmcInit = 2 0
storage init OK!
Using default environment

GetParam
Load FDT from resource image.
power key: bank-0 pin-5
pmic:act8846
can't find dts node for pwm1
DCDC vdd_logic has been used, pwm regulator not init it.
Can't find dts node for fuel guage cw201x
SecureBootEn = 0, SecureBootLock = 0

#Boot ver: 2019-03-18#2.30
empty serial no.
reboot to rockusb.


如图loader设备 校验固件 失败 的 flog



--------------------------------------------------------------
擦除EMMC 成功的 FLOG

DDR Version 1.00 20160530
In
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Memory OK
Memory OK
OUT
DDR Version 1.00 20160530
In
SRX
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
OUT


U-Boot 2014.10-RK3288-10 (Mar 18 2019 - 18:00:13)

CPU: rk3288
cpu version = 0
CPU's clock information:
    arm pll = 600000000HZ
    periph pll = 297000000HZ
    ddr pll = 200000000HZ
    codec pll = 384000000HZ
Board:        Rockchip platform Board
DRAM:  Found dram banks: 1
Adding bank:0000000000000000(0000000080000000)
128 MiB
GIC CPU mask = 0x00000001
SdmmcInit = 0 400
SdmmcInit = 2 0
storage init OK!
Using default environment

GetParam
W: Invalid Parameter's tag (0xFFFFFFFF)!
Invalid parameter
No pmic detect.
SecureBootEn = 0, SecureBootLock = 0

#Boot ver: 2019-03-18#2.30
empty serial no.
Writing env to storage...
done
checkKey
vbus = 0
no fuel gauge found
no fuel gauge found
read logo on state from dts [0]
no fuel gauge found
misc partition not found!
Hit any key to stop autoboot:  0
'boot' does not seem to be a partition nor an address
Unable to boot:boot
try to start recovery
'recovery' does not seem to be a partition nor an address
Unable to boot:recovery
try to start backup
'backup' does not seem to be a partition nor an address
Unable to boot:backup
try to start rockusb
DDR Version 1.00 20160530
In
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Memory OK
Memory OK
OUT
DDR Version 1.00 20160530
In
SRX
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
OUT


U-Boot 2014.10-RK3288-10 (Mar 18 2019 - 18:00:13)

CPU: rk3288
cpu version = 0
CPU's clock information:
    arm pll = 600000000HZ
    periph pll = 297000000HZ
    ddr pll = 200000000HZ
    codec pll = 384000000HZ
Board:        Rockchip platform Board
DRAM:  Found dram banks: 1
Adding bank:0000000000000000(0000000080000000)
128 MiB
GIC CPU mask = 0x00000001
SdmmcInit = 0 400
SdmmcInit = 2 0
storage init OK!
Using default environment

GetParam
W: Invalid Parameter's tag (0xFFFFFFFF)!
Invalid parameter
No pmic detect.
SecureBootEn = 0, SecureBootLock = 0

#Boot ver: 2019-03-18#2.30
empty serial no.
checkKey
vbus = 1
no fuel gauge found
no fuel gauge found
read logo on state from dts [0]
no fuel gauge found
misc partition not found!
Hit any key to stop autoboot:  0
'boot' does not seem to be a partition nor an address
Unable to boot:boot
try to start recovery
'recovery' does not seem to be a partition nor an address
Unable to boot:recovery
try to start backup
'backup' does not seem to be a partition nor an address
Unable to boot:backup
try to start rockusb
DDR Version 1.00 20160530
In
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Memory OK
Memory OK
OUT
DDR Version 1.00 20160530
In
SRX
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
OUT


U-Boot 2014.10-RK3288-10 (Mar 18 2019 - 18:00:13)

CPU: rk3288
cpu version = 0
CPU's clock information:
    arm pll = 600000000HZ
    periph pll = 297000000HZ
    ddr pll = 200000000HZ
    codec pll = 384000000HZ
Board:        Rockchip platform Board
DRAM:  Found dram banks: 1
Adding bank:0000000000000000(0000000080000000)
128 MiB
GIC CPU mask = 0x00000001
SdmmcInit = 0 400
SdmmcInit = 2 0
storage init OK!
Using default environment

GetParam
W: Invalid Parameter's tag (0xFFFFFFFF)!
Invalid parameter
No pmic detect.
SecureBootEn = 0, SecureBootLock = 0

#Boot ver: 2019-03-18#2.30
empty serial no.
checkKey
vbus = 1
no fuel gauge found
no fuel gauge found
read logo on state from dts [0]
no fuel gauge found
misc partition not found!
Hit any key to stop autoboot:  0
'boot' does not seem to be a partition nor an address
Unable to boot:boot
try to start recovery
'recovery' does not seem to be a partition nor an address
Unable to boot:recovery
try to start backup
'backup' does not seem to be a partition nor an address
Unable to boot:backup
try to start rockusb
DDR Version 1.00 20160530
In
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Memory OK
Memory OK
OUT
DDR Version 1.00 20160530
In
SRX
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
OUT


U-Boot 2014.10-RK3288-10 (Mar 18 2019 - 18:00:13)

CPU: rk3288
cpu version = 0
CPU's clock information:
    arm pll = 600000000HZ
    periph pll = 297000000HZ
    ddr pll = 200000000HZ
    codec pll = 384000000HZ
Board:        Rockchip platform Board
DRAM:  Found dram banks: 1
Adding bank:0000000000000000(0000000080000000)
128 MiB
GIC CPU mask = 0x00000001
SdmmcInit = 0 400
SdmmcInit = 2 0
storage init OK!
Using default environment

GetParam
W: Invalid Parameter's tag (0xFFFFFFFF)!
Invalid parameter
No pmic detect.
SecureBootEn = 0, SecureBootLock = 0

#Boot ver: 2019-03-18#2.30
empty serial no.
checkKey
vbus = 1
no fuel gauge found
no fuel gauge found
read logo on state from dts [0]
no fuel gauge found
misc partition not found!
Hit any key to stop autoboot:  0
'boot' does not seem to be a partition nor an address
Unable to boot:boot
try to start recovery
'recovery' does not seem to be a partition nor an address
Unable to boot:recovery
try to start backup
'backup' does not seem to be a partition nor an address
Unable to boot:backup
try to start rockusb
DDR Version 1.00 20160530
In
SRX
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
OUT
usb boot ver:20160218
ChipType = 8
...FlashInit enter...
FtlMallocOffset = 8040 8000
FtlMallocOffset = 10040 8000
FtlMallocOffset = 11040 1000
FtlMallocOffset = 19040 8000
FtlMallocOffset = 1a040 1000
1:200 0 7f7f05 22
...NandcInit enter...
0:1200 0 7f7f05 22 200
FtlMallocOffset = 23040 9000
gNandcVer = 6
SDC_BusRequest:  CMD=8  SDC_RESP_TIMEOUT 1815
  SDC_BusRequest:  CMD=8  SDC_RESP_TIMEOUT 1815
  SDC_BusRequest:  CMD=8  SDC_RESP_TIMEOUT 1815
  SDC_BusRequest:  CMD=5  SDC_RESP_TIMEOUT 1815
  SDC_BusRequest:  CMD=5  SDC_RESP_TIMEOUT 1815
  SDC_BusRequest:  CMD=5  SDC_RESP_TIMEOUT 1815
  SDC_BusRequest:  CMD=55  SDC_RESP_TIMEOUT 1815
  SDC_BusRequest:  CMD=55  SDC_RESP_TIMEOUT 1815
  SDC_BusRequest:  CMD=55  SDC_RESP_TIMEOUT 1815
mmc Ext_csd, ret=0 ,
Ext[226]=20, bootSize=2000,
                 Ext[215]=1, Ext[214]=d1, Ext[213]=f0, Ext[212]=0,cap =1d1f000 REL=1f
SdmmcInit=2 0
BootCapSize=2000
UserCapSize=1d1f000
FwPartOffset=2000 , 2000
UsbHook 596339
powerOn 597255






分享到：QQ空间新浪微博腾讯微博人人网微信
回复

使用道具 举报

Mr.Lee

140

积分

0

威望

0

贡献

社区版主

Rank: 7Rank: 7Rank: 7

积分
140
发表于 2019-7-24 11:38:45        只看该作者  沙发
校验失败可以忽略，loader完成重启能不能启动？
回复

使用道具 举报

peky2018

31

积分

0

威望

0

贡献

技术小白

积分
31
发表于 2019-7-25 08:41:34        只看该作者  板凳
Mr.Lee 发表于 2019-7-24 11:38
校验失败可以忽略，loader完成重启能不能启动？

能够启动，但就是进不去 内核里面
回复

使用道具 举报

Demon

288

积分

0

威望

0

贡献

技术达人

Rank: 2

积分
288
发表于 2019-7-25 09:11:31        只看该作者  地板
这样的情况，首先要根据官网提示，确认工具的版本，烧写须知
然后再下载官网的固件试试，确认问题所在。

回复

使用道具 举报

dolbyyu

47

积分

0

威望

0

贡献

技术小白

积分
47
发表于 2019-7-29 13:01:13        只看该作者  5#
Mr.Lee 发表于 2019-7-24 11:38
校验失败可以忽略，loader完成重启能不能启动？

烧写时，进度直接从28%跳到71%，提示烧写成功，结果开机卡在logo界面，请问什么原因呢
回复

使用道具 举报

Mr.Lee

140

积分

0

威望

0

贡献

社区版主

Rank: 7Rank: 7Rank: 7

积分
140
发表于 2019-7-29 16:15:19        只看该作者  6#
dolbyyu 发表于 2019-7-29 13:01
烧写时，进度直接从28%跳到71%，提示烧写成功，结果开机卡在logo界面，请问什么原因呢

自己做的板？
回复

使用道具 举报

dolbyyu

47

积分

0

威望

0

贡献

技术小白

积分
47
发表于 2019-7-29 16:26:11        只看该作者  7#
Mr.Lee 发表于 2019-7-29 16:15
自己做的板？

你们的板子，你们的固件。目前就是卡在Firefly大logo上，不进入系统
回复

使用道具 举报

返回列表
高级模式
B Color Image Link Quote Code Smilies
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

  •  
Copyright © 2014 Firefly. All Rights Reserved.    
联系我们
技术支持 ： service@t-firefly.com
商务联系 ： sales@t-firefly.com
国内销售经理 ： (+86)13790717706
国内销售经理 ： (+86)16676054231
国外销售经理 ： (+86)15521814828
技术支持
综合支持  ： service@t-firefly.com
MiniPC (①群)  ： 431139193 (已满)
MiniPC (②群)  ： 586343230 (已满)
MiniPC (③群)  ： 708441069 (已满)
MiniPC (④群)  ： 902769718 (已满)
MiniPC (⑤群)  ： 680300610
友情链接 ： 爱板网 电子发烧友论坛 云汉电子社区 粤ICP备14022046号-2
快速回复 返回顶部 返回列表