无法启动Firefly RK3399板子

monica · 发表于 2021-3-2 16:00:09

我购买了Firefly-rk3399，并且试图将操作系统从Android更新为Ubuntu，但现在无法启动。通过USB-c连接或UART / USB连接在主机中看不到它。
我已在更新中附上了故障捕获信息，其中显示了与设备的最后一次通信。
要使此设备重新工作，需要采取什么步骤？
(我是美国客户，如果可以，请回复英文，谢谢)

895816513 · 发表于 2021-3-2 17:45:12

Please use this firmware.
https://drive.google.com/file/d/ ... yT/view?usp=sharing

monica · 发表于 2021-3-3 14:14:13

我的设备显示信息是如附件也是重新固件就可以了吗？

895816513 · 发表于 2021-3-3 14:42:46

monica 发表于 2021-3-3 14:14
我的设备显示信息是如附件也是重新固件就可以了吗？

你先用那个固件，进入maskrom升级模式，升级看看能不能正常启动。怀疑你之前用错固件。

895816513 · 发表于 2021-3-3 14:44:46

参考
http://wiki.t-firefly.com/en/Firefly-RK3399/02-upgrade_table.html

monica · 发表于 2021-3-4 10:11:15

The firmware suggested was already tried. After being off for a couple
of days, it showed up in Maskrom mode this morning. I tried the firmware
from the link and it fails. Here is the screen capture of the results:
Please let me know what else I can do!
Thanks!See the attached

I'm attaching the image which might not have gotten through.The log file showed:11:18:53 452 RKDevTool v[link removed] start run11:20:37 913 Layer<1-3>:Download Boot Start11:20:41 757 Layer<1-3>:Download Boot Success11:20:41 759 Layer<1-3>:Wait For Maskrom Start11:20:42 227 Layer<1-3>:Wait For Maskrom Success11:20:42 231 Layer<1-3>:Test Device Start11:20:42 234 Layer<1-3>:Test Device Success11:20:42 238 Layer<1-3>:Check Chip Start11:20:42 241 Layer<1-3>: Check Chip Success11:20:42 244 Layer<1-3>:Get FlashInfo Start11:20:42 245 <LAYER 1-3> INFO:FlashInfo: 00 00 00 00 00 04 04 00 28 00 0011:20:42 247 <LAYER 1-3> INFO:GetFlashInfo-->Emmc storage.11:20:42 252 Layer<1-3>:Get FlashInfo Success11:20:42 255 Layer<1-3>:Prepare IDB Start11:20:42 256 <LAYER 1-3> ERROR:PrepareIDB-->No Found 1st Flash CS11:20:42 259 Error:Layer<1-3>:Prepare IDB FailAnd the UART output showed:DDR Version 1.22 20190506InChannel 0: DDR3, 800MHzBus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MBChannel 1: DDR3, 800MHzBus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB256B stridech 0 ddrconfig = 0x101, ddrsize = 0x2020ch 1 ddrconfig = 0x101, ddrsize = 0x2020pmugrf_os_reg[2] = 0x3AA17AA1, stride = 0xDOUTBoot1: 2019-03-14, version: 1.19CPUId = 0x0mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000mmc: ERROR: Card did not respond to voltage select!emmc reinitmmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000mmc: ERROR: Card did not respond to voltage select!emmc reinitmmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000mmc: ERROR: Card did not respond to voltage select!SdmmcInit=2 1UsbHook 57663powerOn 57746

895816513 · 发表于 2021-3-4 10:53:06

You try to use the upgrade_tool tool to upgrade on the ubuntu system. Enter Maskrom mode, lsusb mode detects whether there is a usb device, first erase and then write the firmware program.

monica · 发表于 2021-3-5 09:47:18

I have tried the same process on Ubuntu! Also tried the rkdeveloptool to
erase it. Nothing has worked.
The documentation mentions RK3399_Android7.1_EraseIDB.7z but I cannot
find it to download. I have found a link to the Erase_IDB on the Baidu
site. But I cannot create a login and I cannot read the language. The
device will not load any firmware.
Here is the output from running the upgrade_tool on Linux:
gha@ubuntu:~/firefly-rk3399/u34/Linux_Upgrade_Tool/Linux_Upgrade_Tool$
sudo ./upgrade_tool ef FIREFLY-RK3399-UBUNTU18.04-GPT-20200714-1510.img
Program Data in /home/gha/.config/upgrade_tool
Loading loader...
Erase flash ok.
gha@ubuntu:~/firefly-rk3399/u34/Linux_Upgrade_Tool/Linux_Upgrade_Tool$
sudo ./upgrade_tool uf FIREFLY-RK3399-UBUNTU18.04-GPT-20200714-1510.img
Program Data in /home/gha/.config/upgrade_tool
Loading firmware...
Support Type:RK330C FW Ver:8.1.40 FW Time:2020-07-14 15:11:41
Loader ver:1.19 Loader Time:2020-07-14 15:10:09
Prepare IDB Fail
Here is the serial UART Debug output during the above. Note: I have to
power off/on the RK3399 after the erase (EF) in order for the UF comand
to proceed to the IDB failure.
DDR Version 1.22 20190506
In
Channel 0: DDR3, 800MHz
Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB
Channel 1: DDR3, 800MHz
Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB
256B stride
ch 0 ddrconfig = 0x101, ddrsize = 0x2020
ch 1 ddrconfig = 0x101, ddrsize = 0x2020
pmugrf_os_reg[2] = 0x3AA17AA1, stride = 0xD
OUT
Boot1: 2019-03-14, version: 1.19
CPUId = 0x0
mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000
mmc: ERROR: Card did not respond to voltage select!
emmc reinit
mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000
mmc: ERROR: Card did not respond to voltage select!
emmc reinit
mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000
mmc: ERROR: Card did not respond to voltage select!
SdmmcInit=2 1
UsbHook 57794
powerOn 57875
DDR Version 1.22 20190506
In
soft reset
DDR Version 1.22 20190506
In
Channel

895816513 · 发表于 2021-3-5 10:33:36

Have you inserted the SD card? Please pull out the SD card and try again.

monica · 发表于 2021-3-5 12:00:02

I have tried the same process on Ubuntu! Also tried the rkdeveloptool to
erase it. Nothing has worked.
The documentation mentions RK3399_Android7.1_EraseIDB.7z but I cannot
find it to download. I have found a link to the Erase_IDB on the Baidu
site

[Linux] 无法启动Firefly RK3399板子

【Linux】无法启动Firefly RK3399板子

[Linux] 无法启动Firefly RK3399板子

【Linux】 无法启动Firefly RK3399板子

【Linux】无法启动Firefly RK3399板子