QUINTIC的pwm

thong

最近准备用QUINTIC的PWM，把自带的PWM例程烧到板子里面去发现IO并没有PWM输出，不知道有没有试过PWM，所以想请教下问题在哪儿？

FireBLE_blue

hi，thong
你说的自带的pwm例程是否是 \FireBLE\Demo_driver\pwm 下编译而来？如是请看确认main 函数和如下代码一致

1. int main (void)
   
2. {
   
3.     SystemInit();
   
4. 
   
5.     pwm_init(PWM_CH0);
   
6.     pwm_io_config();
   
7.     //P2.7 will output pwm wave with period for 1000us and pulse for 400us
   
8.     pwm_config(PWM_CH0, PWM_PSCAL_DIV, PWM_COUNT_US(1000, PWM_PSCAL_DIV), PWM_COUNT_US(400, PWM_PSCAL_DIV));
   
9.     pwm_enable(PWM_CH0, MASK_ENABLE);
   
10.     pwm_config(PWM_CH0, PWM_PSCAL_DIV, PWM_COUNT_US(1000, PWM_PSCAL_DIV), PWM_COUNT_US(800, PWM_PSCAL_DIV));
    
11.     pwm_config(PWM_CH0, PWM_PSCAL_DIV, PWM_COUNT_US(1000, PWM_PSCAL_DIV), PWM_COUNT_US(1000, PWM_PSCAL_DIV));
    
12.     pwm_config(PWM_CH0, PWM_PSCAL_DIV, PWM_COUNT_US(1000, PWM_PSCAL_DIV), PWM_COUNT_US(0, PWM_PSCAL_DIV));
    
13.     pwm_config(PWM_CH0, PWM_PSCAL_DIV, PWM_COUNT_US(1000, PWM_PSCAL_DIV), PWM_COUNT_US(400, PWM_PSCAL_DIV));
    
14.     pwm_config(PWM_CH0, PWM_PSCAL_DIV, PWM_COUNT_US(1000, PWM_PSCAL_DIV), PWM_COUNT_US(800, PWM_PSCAL_DIV));
    
15.     pwm_config(PWM_CH0, PWM_PSCAL_DIV, PWM_COUNT_US(1000, PWM_PSCAL_DIV), PWM_COUNT_US(1000, PWM_PSCAL_DIV));
    
16.     pwm_config(PWM_CH0, PWM_PSCAL_DIV, PWM_COUNT_US(1000, PWM_PSCAL_DIV), PWM_COUNT_US(0, PWM_PSCAL_DIV));
    
17.     pwm_config(PWM_CH0, PWM_PSCAL_DIV, PWM_COUNT_US(1000, PWM_PSCAL_DIV), PWM_COUNT_US(800, PWM_PSCAL_DIV));
    
18.     pwm_enable(PWM_CH0, MASK_DISABLE);
    
19.     pwm_io_dis_config();
    
20. 
    
21.     pwm_init(PWM_CH1);
    
22.     pwm_io_config();
    
23.     //P2.6 will output pwm wave with period for 1500us and pulse for 1000us
    
24.     pwm_config(PWM_CH1, 119, PWM_COUNT_US(1500, 119), PWM_COUNT_US(1000, 119));
    
25.     pwm_enable(PWM_CH1, MASK_ENABLE);
    
26.     pwm_io_dis_config();
    
27. 
    
28.     while (1)                                /* Loop forever */
    
29.     {
    
30. 
    
31.     }
    
32. }

复制代码

该份代码在单步仿真的情况下能得到pwm 输出，
如果你是编译后烧录进去的话，需要对代码做些小改动，至于怎么改动，请分析源码

thong

FireBLE_blue 发表于 2015-4-20 14:41
hi，thong
你说的自带的pwm例程是否是 \FireBLE\Demo_driver\pwm 下编译而来？如是请看确认main 函数和如 ...

void pwm_io_dis_config(void)
{

    syscon_SetPMCR1(QN_SYSCON, P27_GPIO_23_PIN_CTRL         //P2.7 GPIO
                             | P26_GPIO_22_PIN_CTRL         //P2.6 GPIO
                             );
    gpio_set_direction_field(GPIO_P27|GPIO_P26, GPIO_INPUT);
}
PWM不是输出吗，为什么这个地方的IO方向会是输入呢？

FireBLE_blue

1. pwm_io_config();

复制代码

是配合pwm io 的配置

1. pwm_io_dis_config();

复制代码

是配合pwm io 的反配置，注意关键字眼dis = disable