Firefly开源社区

[Android] 请问一下,Android10.0系统启动卡在这个位置不动了,麻烦各位大佬看看

35

积分

0

威望

0

贡献

技术小白

积分
35
发表于 2021-9-14 15:49:50     
DDR Version 1.24 20191016
In
channel 0
CS = 0
MR0=0x98
MR4=0x1
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 1
CS = 0
MR0=0x98
MR4=0x1
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 0 training pass!
channel 1 training pass!
change freq to 416MHz 0,1
Channel 0: LPDDR4,416MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel 1: LPDDR4,416MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
256B stride
channel 0
CS = 0
MR0=0x98
MR4=0x1
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 1
CS = 0
MR0=0x98
MR4=0x1
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 0 training pass!
channel 1 training pass!
channel 0, cs 0, advanced training done
channel 1, cs 0, advanced training done
change freq to 856MHz 1,0
ch 0 ddrconfig = 0x101, ddrsize = 0x20
ch 1 ddrconfig = 0x101, ddrsize = 0x20
pmugrf_os_reg[2] = 0x3281F281, stride = 0x9
ddr_set_rate to 328MHZ
ddr_set_rate to 666MHZ
ddr_set_rate to 416MHZ, ctl_index 0
ddr_set_rate to 856MHZ, ctl_index 1
support 416 856 328 666 MHz, current 856MHz
OUT
Boot1 Release Time: May 29 2020 17:36:36, version: 1.26
CPUId = 0x0
ChipType = 0x10, 346
SdmmcInit=2 0
BootCapSize=100000
UserCapSize=7456MB
FwPartOffset=2000 , 100000
mmc0:cmd8,20
mmc0:cmd5,20
mmc0:cmd55,20
mmc0:cmd1,20
mmc0:cmd8,20
mmc0:cmd5,20
mmc0:cmd55,20
mmc0:cmd1,20
mmc0:cmd8,20
mmc0:cmd5,20
mmc0:cmd55,20
mmc0:cmd1,20
SdmmcInit=0 1
StorageInit ok = 69373
SecureMode = 0
SecureInit read PBA: 0x4
SecureInit read PBA: 0x404
SecureInit read PBA: 0x804
SecureInit read PBA: 0xc04
SecureInit read PBA: 0x1004
SecureInit read PBA: 0x1404
SecureInit read PBA: 0x1804
SecureInit read PBA: 0x1c04
SecureInit ret = 0, SecureMode = 0
atags_set_bootdev: ret:(0)
GPT part:  0, name:            uboot, start:0x2000, size:0x2000
GPT part:  1, name:            trust, start:0x4000, size:0x2000
GPT part:  2, name:             misc, start:0x6000, size:0x2000
GPT part:  3, name:             dtbo, start:0xc000, size:0x2000
GPT part:  4, name:           vbmeta, start:0xe000, size:0x800
GPT part:  5, name:         resource, start:0x8000, size:0x8000
GPT part:  6, name:           kernel, start:0x10000, size:0xc000
GPT part:  7, name:             boot, start:0xe800, size:0x10000
GPT part:  8, name:         recovery, start:0x1e800, size:0x30000
GPT part:  9, name:           backup, start:0x4e800, size:0x38000
GPT part: 10, name:         security, start:0x86800, size:0x2000
GPT part: 11, name:            cache, start:0x88800, size:0xc0000
GPT part: 12, name:         metadata, start:0x148800, size:0x8000
GPT part: 13, name:              frp, start:0x150800, size:0x400
GPT part: 14, name:            super, start:0x150c00, size:0x714000
GPT part: 15, name:              oem, start:0x864c00, size:0x100000
GPT part: 16, name:         userdata, start:0x964c00, size:0x52b3df
find part:uboot OK. first_lba:0x2000.
find part:trust OK. first_lba:0x4000.
Trust Addr:0x4000, 0x58334c42
No find bl30.bin
Load uboot, ReadLba = 2000
Load OK, addr=0x200000, size=0xfb1c8
RunBL31 0x40000 @ 117026 us
NOTICE:  BL31: v1.3(release):845ee93
NOTICE:  BL31: Built : 15:51:11, Jul 22 2020
NOTICE:  BL31: Rockchip release version: v1.1
INFO:    GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 0
INFO:    plat_rockchip_pmu_init(1196): pd status 3e
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
INF [0x0] TEE-CORE:init_primary_helper:337: Initializing (1.1.0-266-gee81607c #1 Mon Aug 17 09:23:30 UTC 2020 aarch64)

INF [0x0] TEE-CORE:init_primary_helper:338: Release version: 1.2

INF [0x0] TEE-CORE:init_teecore:83: teecore inits done
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


U-Boot 2017.09 (Aug 31 2021 - 17:48:37 +0800)

Model: Rockchip RK3399 Evaluation Board
PreSerial: 2
DRAM:  2 GiB
Sysmem: init
Relocation Offset: 7dbc8000, fdt: 7bdbc358
Using default environment

dwmmc@fe320000: 1, sdhci@fe330000: 0
Bootdev(atags): mmc 0
MMC0: HS400, 150Mhz
PartType: EFI
Android 10.0, Build 2020.11
boot mode: recovery (misc)
Found DTB in recovery part
DTB: rk-kernel.dtb
HASH(c): OK
ANDROID: fdt overlay OK
I2c0 speed: 400000Hz
PMIC:  RK808
vdd_center 900000 uV
vdd_cpu_l 900000 uV
vdd_log 1000000 uV
Model: ROC-RK3399-PC-PLUS HDMI+DP(Android)
Rockchip UBOOT DRM driver version: v1.0.1
CLK: (uboot. arml: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
CLK: (uboot. armb: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
  aplll 816000 KHz
  apllb 816000 KHz
  dpll 856000 KHz
  cpll 24000 KHz
  gpll 800000 KHz
  npll 600000 KHz
  vpll 24000 KHz
  aclk_perihp 133333 KHz
  hclk_perihp 66666 KHz
  pclk_perihp 33333 KHz
  aclk_perilp0 266666 KHz
  hclk_perilp0 88888 KHz
  pclk_perilp0 44444 KHz
  hclk_perilp1 100000 KHz
  pclk_perilp1 50000 KHz
Net:   eth0: ethernet@fe300000
Hit key to stop autoboot('CTRL+C'):  0
ANDROID: reboot reason: "recovery"
optee api revision: 2.0
Vboot=0, AVB images, AVB verify
read_is_device_unlocked() ops returned that device is UNLOCKED
avb_slot_verify.c:757: ERROR: vbmeta: Error verifying vbmeta image: OK_NOT_SIGNED
get image from preloaded partition...
Could not find "system" partition
Booting IMAGE kernel at 0x00280000 with fdt at 0x08300000...


Fdt Ramdisk skip relocation
## Booting Android Image at 0x0027f800 ...
Kernel load addr 0x00280000 size 25789 KiB
RAM disk load addr 0x0a200000 size 7949 KiB
## Flattened Device Tree blob at 08300000
   Booting using the fdt blob at 0x8300000
   XIP Kernel Image from 0x00280000 to 0x00280000 ... OK
  'reserved-memory' ramoops@110000: addr=110000 size=f0000
   Using Device Tree in place at 0000000008300000, end 000000000831da47
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x0a200000 - 0x80000000 (size: 0x75e00000)
Total: 753.264 ms

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 4.19.111 (le@le-desktop) (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05)) #5 SMP PREEMPT Fri Sep 10 15:18:21 CST 2021
[    0.000000] Machine model: ROC-RK3399-PC-PLUS HDMI+DP(Android)
[    0.000000] earlycon: uart8250 at MMIO32 0x00000000ff1a0000 (options '')
[    0.000000] bootconsole [uart8250] enabled
[    0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'stb-devinfo@00000000': base 0x0000000000000000, size 0 MiB
[    0.000000] cma: Reserved 16 MiB at 0x000000007f000000
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: Trusted OS migration not required
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] percpu: Embedded 23 pages/cpu s57304 r8192 d28712 u94208
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 507912
[    0.000000] Kernel command line: storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal  androidboot.dtbo_idx=0  androidboot.verifiedbootstate=orange androidboot.slot_suffix= androidboot.serialno=WUH5KZZ0G9 console=ttyFIQ0 androidboot.baseband=N/A androidboot.selinux=permissive androidboot.wificountrycode=US androidboot.veritymode=enforcing androidboot.hardware=rk30board androidboot.console=ttyFIQ0 firmware_class.path=/vendor/etc/firmware init=/init root=PARTUUID=af01642c-9b84-11e8-9b2a-234eb5e198a0 earlycon=uart8250,mmio32,0xff1a0000 swiotlb=1 coherent_pool=1m androidboot.boot_devices=fe330000.sdhci,fe320000.dwmmc
[    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 1972684K/2064384K available (14334K kernel code, 1788K rwdata, 5664K rodata, 3968K init, 2243K bss, 75316K reserved, 16384K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
[    0.000000]  Tasks RCU enabled.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[    0.000000] GICv3: Distributor has no Range Selector support
[    0.000000] GICv3: no VLPI support, no direct LPI support
[    0.000000] ITS [mem 0xfee20000-0xfee3ffff]
[    0.000000] ITS@0x00000000fee20000: allocated 65536 Devices @7b880000 (flat, esz 8, psz 64K, shr 0)
[    0.000000] ITS: using cache flushing for cmd queue
[    0.000000] GIC: using LPI property table @0x000000007b820000
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fef00000
[    0.000000] CPU0: using LPI pending table @0x000000007b830000
[    0.000000] GIC: using cache flushing for LPI property table
[    0.000000] GICv3: GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
[    0.000000] GICv3: GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
[    0.000000] random: random: get_random_bytes called from start_kernel+0x36c/0x4ec with crng_init=0
[    0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop0_frac as parent of dclk_vop0, rate changes may not work
[    0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop1_frac as parent of dclk_vop1, rate changes may not work
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.002034] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=24000)
[    0.003019] pid_max: default: 32768 minimum: 301
[    0.003583] Security Framework initialized
[    0.003977] SELinux:  Initializing.
[    0.004439] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.005083] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.007327] ASID allocator initialised with 32768 entries
[    0.007952] rcu: Hierarchical SRCU implementation.
[    0.008822] Platform MSI: interrupt-controller@fee20000 domain created
[    0.009965] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[    0.011619] smp: Bringing up secondary CPUs ...
[    0.012684] Detected VIPT I-cache on CPU1
[    0.012720] GICv3: CPU1: found redistributor 1 region 0:0x00000000fef20000
[    0.012758] CPU1: using LPI pending table @0x000000007ba10000
[    0.012803] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.013691] Detected VIPT I-cache on CPU2
[    0.013726] GICv3: CPU2: found redistributor 2 region 0:0x00000000fef40000
[    0.013764] CPU2: using LPI pending table @0x000000007ba70000
[    0.013808] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.014629] Detected VIPT I-cache on CPU3
[    0.014662] GICv3: CPU3: found redistributor 3 region 0:0x00000000fef60000
[    0.014700] CPU3: using LPI pending table @0x000000007ba80000
[    0.014743] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.015603] ARM_SMCCC_ARCH_WORKAROUND_1 missing from firmware
[    0.015609] CPU features: enabling workaround for EL2 vector hardening
[    0.015618] Detected PIPT I-cache on CPU4
[    0.015643] GICv3: CPU4: found redistributor 100 region 0:0x00000000fef80000
[    0.015693] CPU4: using LPI pending table @0x000000007bae0000
[    0.015722] CPU4: Booted secondary processor 0x0000000100 [0x410fd082]
[    0.016439] Detected PIPT I-cache on CPU5
[    0.016466] GICv3: CPU5: found redistributor 101 region 0:0x00000000fefa0000
[    0.016517] CPU5: using LPI pending table @0x000000007baf0000
[    0.016546] CPU5: Booted secondary processor 0x0000000101 [0x410fd082]
[    0.016655] smp: Brought up 1 node, 6 CPUs
[    0.029265] SMP: Total of 6 processors activated.
[    0.029715] CPU features: detected: GIC system register CPU interface
[    0.030339] CPU features: detected: 32-bit EL0 Support
[    0.037015] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[    0.037821] CPU: All CPU(s) started at EL2
[    0.038255] alternatives: patching kernel code
[    0.040173] devtmpfs: initialized
[    0.054591] Trying to unpack rootfs image as initramfs...
[    0.055108] Registered cp15_barrier emulation handler
[    0.055122] Registered setend emulation handler
[    0.055477] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[    0.056939] futex hash table entries: 2048 (order: 5, 131072 bytes)
[    0.057923] pinctrl core: initialized pinctrl subsystem
[    0.059030] NET: Registered protocol family 16
[    0.060162] schedtune: configured to support 6 boost groups
[    0.060917] audit: initializing netlink subsys (disabled)
[    0.062125] audit: type=2000 audit(0.055:1): state=initialized audit_enabled=0 res=1
[    0.062885] cpuidle: using governor menu
[    0.063272] Registered FIQ tty driver
[    0.064070] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.072800] DMA: preallocated 1024 KiB pool for atomic allocations
[    0.075194] console [pstore-1] enabled
[    0.075673] pstore: Registered ramoops as persistent store backend
[    0.076266] ramoops: attached 0xf0000@0x110000, ecc: 0/0
[    0.106694] cryptd: max_cpu_qlen set to 1000
[    0.107864] fiq debugger fiq mode enabled
[[    0.108459] console [ttyFIQ0] enabled
    0.108459] console [ttyFIQ0] enabled
[    0.109149] bootconsole [uart8250] disabled
[    0.109149] bootconsole [uart8250] disabled
[    0.109756] Registered fiq debugger ttyFIQ0
[    0.111062] vcc_sys: supplied by dc_12v
[    0.113352] rk_iommu ff650800.iommu: version = 1
[    0.113786] rk_iommu ff660480.iommu: version = 1
[    0.114050] rk_iommu ff670800.iommu: version = 1
[    0.114344] rk_iommu ff8f3f00.iommu: version = 1
[    0.114580] rk_iommu ff903f00.iommu: version = 1
[    0.114820] rk_iommu ff914000.iommu: version = 1
[    0.115071] rk_iommu ff924000.iommu: version = 1
[    0.115603] SCSI subsystem initialized
[    0.115956] usbcore: registered new interface driver usbfs
[    0.116019] usbcore: registered new interface driver hub
[    0.116104] usbcore: registered new device driver usb
[    0.116363] media: Linux media interface: v0.10
[    0.116397] videodev: Linux video capture interface: v2.00
[    0.116451] pps_core: LinuxPPS API ver. 1 registered
[    0.116465] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.116485] PTP clock support registered
[    0.118213] Advanced Linux Sound Architecture Driver Initialized.
[    0.118544] Bluetooth: Core ver 2.22
[    0.118583] NET: Registered protocol family 31
[    0.118618] Bluetooth: HCI device and connection manager initialized
[    0.118637] Bluetooth: HCI socket layer initialized
[    0.118650] Bluetooth: L2CAP socket layer initialized
[    0.118681] Bluetooth: SCO socket layer initialized
[    0.119046] rockchip-cpuinfo cpuinfo: SoC            : 0
[    0.119065] rockchip-cpuinfo cpuinfo: Serial         : 7d9418e5de243167
[    0.119588] clocksource: Switched to clocksource arch_sys_counter
[    0.173980] VFS: Disk quotas dquot_6.6.0
[    0.174056] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.175203] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[    0.183749] NET: Registered protocol family 2
[    0.184190] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes)
[    0.184235] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.184373] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[    0.184645] TCP: Hash tables configured (established 16384 bind 16384)
[    0.184762] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[    0.184820] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[    0.184974] NET: Registered protocol family 1
[    0.187045] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[    0.187320] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
[    0.188797] Initialise system trusted keyrings
[    0.188969] workingset: timestamp_bits=45 max_order=19 bucket_order=0
[    0.192749] Registering sdcardfs 0.1
[    0.193643] fuse init (API version 7.27)
[    0.194803]
[    0.194803] TEE Core Framework initialization (ver 1:0.1)
[    0.194831] TEE armv7 Driver initialization
[    0.195197] tz_tee_probe: name="armv7sec", id=0, pdev_name="armv7sec.0"
[    0.195214] TEE core: Alloc the misc device "opteearmtz00" (id=0)
[    0.195383] TEE Core: Register the misc device "opteearmtz00" (id=0,minor=62)
[    0.196502] Key type asymmetric registered
[    0.196518] Asymmetric key parser 'x509' registered
[    0.196554] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[    0.196564] io scheduler noop registered
[    0.196679] io scheduler cfq registered (default)
[    0.196692] io scheduler mq-deadline registered
[    0.196700] io scheduler kyber registered
[    0.196775] io scheduler bfq registered
[    0.198445] phy phy-ff770000.syscon:usb2-phy@e460.1: Linked as a consumer to regulator.4
[    0.198850] phy phy-ff770000.syscon:usb2-phy@e460.2: Failed to get VBUS supply regulator
[    0.200190] rockchip-mipi-dphy-rx ff770000.syscon:mipi-dphy-rx0: invalid resource
[    0.203352] rockchip-pcie f8000000.pcie: missing "memory-region" property
[    0.203484] rockchip-pcie f8000000.pcie: no vpcie12v regulator found
[    0.203554] rockchip-pcie f8000000.pcie: Linked as a consumer to regulator.8
[    0.203597] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found
[    0.203619] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found
[    0.203654] rockchip-pcie f8000000.pcie: host bridge /pcie@f8000000 ranges:
[    0.203679] rockchip-pcie f8000000.pcie:   MEM 0xfa000000..0xfbdfffff -> 0xfa000000
[    0.203697] rockchip-pcie f8000000.pcie:    IO 0xfbe00000..0xfbefffff -> 0xfbe00000
[    0.415108] Freeing initrd memory: 7948K
[    1.215595] phy phy-ff770000.syscon:pcie-phy.3: pll lock timeout!
[    1.215616] phy phy-ff770000.syscon:pcie-phy.3: phy poweron failed --> -22
[    1.215630] rockchip-pcie f8000000.pcie: power on phy0 err -22
[    1.215647] rockchip-pcie f8000000.pcie: deferred probe failed
[    1.215762] rockchip-pcie f8000000.pcie: Dropping the link to regulator.8
[    1.215858] rockchip-pcie: probe of f8000000.pcie failed with error -22
[    1.216440] iommu: Adding device ff670000.iep to group 2
[    1.216462] iep ff670000.iep: Linked as a consumer to ff670800.iommu
[    1.216677] iep: failed to find iep power down clock source.
[    1.217062] iep: IEP Power ON
[    1.217102] iep: IEP Power OFF
[    1.217121] iep: IEP Driver loaded succesfully
[    1.217267] iep: Module initialized.
[    1.217389] mpp_service mpp-srv: probe start
[    1.217766] iommu: Adding device ff660000.rkvdec to group 1
[    1.217788] mpp_rkvdec ff660000.rkvdec: Linked as a consumer to ff660480.iommu
[    1.217961] mpp_rkvdec ff660000.rkvdec: probing start
[    1.218301] rkvdec_init:1178: failed on clk_get clk_hevc_cabac
[    1.218366] mpp_rkvdec ff660000.rkvdec: shared_video_hevc_cabac is not found!
[    1.218374] rkvdec_init:1206: No hevc cabac reset resource define
[    1.218565] mpp_rkvdec ff660000.rkvdec: probing finish
[    1.219389] iommu: Adding device ff650400.vdpu to group 0
[    1.219423] mpp_vdpu2 ff650400.vdpu: Linked as a consumer to ff650800.iommu
[    1.219610] mpp_vdpu2 ff650400.vdpu: probe device
[    1.219935] mpp_vdpu2 ff650400.vdpu: reset_group->rw_sem_on=0
[    1.219960] mpp_vdpu2 ff650400.vdpu: reset_group->rw_sem_on=0
[    1.220127] mpp_vdpu2 ff650400.vdpu: probing finish
[    1.220484] iommu: Adding device ff650000.vepu to group 0
[    1.220513] mpp_vepu2 ff650000.vepu: Linked as a consumer to ff650800.iommu
[    1.220558] mpp_vepu2 ff650000.vepu: probe device
[    1.220903] mpp_vepu2 ff650000.vepu: reset_group->rw_sem_on=0
[    1.220932] mpp_vepu2 ff650000.vepu: reset_group->rw_sem_on=0
[    1.221081] mpp_vepu2 ff650000.vepu: probing finish
[    1.221263] mpp_service mpp-srv: probe success
[    1.223796] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    1.223820] dma-pl330 ff6d0000.dma-controller:       DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
[    1.224849] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    1.224870] dma-pl330 ff6e0000.dma-controller:       DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[    1.225932] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[    1.226312] pwm-regulator: supplied by regulator-dummy
[    1.226852] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[    1.227336] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 37, base_baud = 1500000) is a 16550A
[    1.229007] random: fast init done
[    1.229153] iommu: Adding device ff8f0000.vop to group 3
[    1.229183] rockchip-vop ff8f0000.vop: Linked as a consumer to ff8f3f00.iommu
[    1.229323] random: crng init done
[    1.229519] iommu: Adding device ff900000.vop to group 4
[    1.229547] rockchip-vop ff900000.vop: Linked as a consumer to ff903f00.iommu
[    1.232605] rockchip-drm display-subsystem: Linked as a consumer to ff8f0000.vop
[    1.232642] rockchip-drm display-subsystem: Linked as a consumer to ff900000.vop
[    1.233254] rockchip-drm display-subsystem: Linked as a consumer to fec00000.dp
[    1.233561] rockchip-drm display-subsystem: Linked as a consumer to ff940000.hdmi
[    1.237607] mali ff9a0000.gpu: Failed to get regulator
[    1.237623] mali ff9a0000.gpu: Power control initialization failed
[    1.237898] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    1.243277] brd: module loaded
[    1.255448] loop: module loaded
[    1.255809] zram: Added device: zram0
[    1.256375] SCSI Media Changer driver v0.25
[    1.257451] rockchip-spi ff1d0000.spi: Failed to request TX DMA channel
[    1.257471] rockchip-spi ff1d0000.spi: Failed to request RX DMA channel
[    1.257482] rockchip-spi ff1d0000.spi: no high_speed pinctrl state
[    1.257830] rockchip-spi ff1d0000.spi: chipselect 0 already in use
[    1.257847] spi_master spi0: spi_device register error /spi@ff1d0000/spi_wk2xxx@00
[    1.257862] spi_master spi0: Failed to create SPI device for /spi@ff1d0000/spi_wk2xxx@00
[    1.258309] register firefly_spi_init spi return v = :0
[    1.258502] libphy: Fixed MDIO Bus: probed
[    1.258533] tun: Universal TUN/TAP device driver, 1.6
[    1.259128] force_sf_dma_mode is ignored if force_thresh_dma_mode is set.
[    1.259154] rk_gmac-dwmac fe300000.ethernet: PTP uses main clock
[    1.259233] rk_gmac-dwmac fe300000.ethernet: Linked as a consumer to regulator.6
[    1.259251] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
[    1.259269] rk_gmac-dwmac fe300000.ethernet: TX delay(0x2e).
[    1.259280] rk_gmac-dwmac fe300000.ethernet: RX delay(0x23).
[    1.259294] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
[    1.259340] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
[    1.259352] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
[    1.264398] rk_gmac-dwmac fe300000.ethernet: init for RGMII
[    1.264584] rk_gmac-dwmac fe300000.ethernet: User ID: 0x10, Synopsys ID: 0x35
[    1.264601] rk_gmac-dwmac fe300000.ethernet:         DWMAC1000
[    1.264611] rk_gmac-dwmac fe300000.ethernet: DMA HW capability register supported
[    1.264623] rk_gmac-dwmac fe300000.ethernet: RX Checksum Offload Engine supported
[    1.264632] rk_gmac-dwmac fe300000.ethernet: COE Type 2
[    1.264643] rk_gmac-dwmac fe300000.ethernet: Wake-Up On Lan supported
[    1.264672] rk_gmac-dwmac fe300000.ethernet: Normal descriptors
[    1.264684] rk_gmac-dwmac fe300000.ethernet: Ring mode enabled
[    1.264693] rk_gmac-dwmac fe300000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    1.336146] libphy: stmmac: probed
[    1.336168] mdio_bus stmmac-0:00: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[    1.336178] mdio_bus stmmac-0:01: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
[    1.337054] PPP generic driver version 2.4.2
[    1.337192] PPP BSD Compression module registered
[    1.337208] PPP Deflate Compression module registered
[    1.337242] PPP MPPE Compression module registered
[    1.337256] NET: Registered protocol family 24
[    1.337278] PPTP driver version 0.8.5
[    1.337551] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[    1.337564] CSLIP: code copyright 1989 Regents of the University of California.
[    1.337646] usbcore: registered new interface driver catc
[    1.337691] usbcore: registered new interface driver kaweth
[    1.337705] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[    1.337738] usbcore: registered new interface driver pegasus
[    1.337774] usbcore: registered new interface driver rtl8150
[    1.337815] usbcore: registered new interface driver r8152
[    1.337828] hso: drivers/net/usb/hso.c: Option Wireless
[    1.337880] usbcore: registered new interface driver hso
[    1.337913] usbcore: registered new interface driver asix
[    1.337949] usbcore: registered new interface driver ax88179_178a
[    1.337984] usbcore: registered new interface driver cdc_ether
[    1.338018] usbcore: registered new interface driver cdc_eem
[    1.338056] usbcore: registered new interface driver dm9601
[    1.338097] usbcore: registered new interface driver smsc75xx
[    1.338132] usbcore: registered new interface driver smsc95xx
[    1.338166] usbcore: registered new interface driver gl620a
[    1.338203] usbcore: registered new interface driver net1080
[    1.338238] usbcore: registered new interface driver plusb
[    1.338272] usbcore: registered new interface driver rndis_host
[    1.338307] usbcore: registered new interface driver cdc_subset
[    1.338342] usbcore: registered new interface driver zaurus
[    1.338374] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[    1.338412] usbcore: registered new interface driver int51x1
[    1.338449] usbcore: registered new interface driver kalmia
[    1.338483] usbcore: registered new interface driver ipheth
[    1.338521] usbcore: registered new interface driver sierra_net
[    1.338557] usbcore: registered new interface driver cx82310_eth
[    1.338612] usbcore: registered new interface driver cdc_ncm
[    1.338649] usbcore: registered new interface driver qmi_wwan
[    1.338683] usbcore: registered new interface driver cdc_mbim
[    1.339631] dwc3 fe900000.dwc3: Failed to get clk 'ref': -2
[    1.344186] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.344203] ehci-pci: EHCI PCI platform driver
[    1.344255] ehci-platform: EHCI generic platform driver
[    1.346556] ehci-platform fe3c0000.usb: EHCI Host Controller
[    1.346704] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 1
[    1.346963] ehci-platform fe3c0000.usb: irq 33, io mem 0xfe3c0000
[    1.353590] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
[    1.353723] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[    1.353740] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.353754] usb usb1: Product: EHCI Host Controller
[    1.353766] usb usb1: Manufacturer: Linux 4.19.111 ehci_hcd
[    1.353778] usb usb1: SerialNumber: fe3c0000.usb
[    1.354134] hub 1-0:1.0: USB hub found
[    1.354173] hub 1-0:1.0: 1 port detected
[    1.354708] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.354728] ohci-platform: OHCI generic platform driver
[    1.355003] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
[    1.355138] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 2
[    1.355364] ohci-platform fe3e0000.usb: irq 34, io mem 0xfe3e0000
[    1.410728] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[    1.410746] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.410756] usb usb2: Product: Generic Platform OHCI controller
[    1.410765] usb usb2: Manufacturer: Linux 4.19.111 ohci_hcd
[    1.410774] usb usb2: SerialNumber: fe3e0000.usb
[    1.411122] hub 2-0:1.0: USB hub found
[    1.411161] hub 2-0:1.0: 1 port detected
[    1.412184] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    1.412339] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 3
[    1.412781] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000005002030010
[    1.412827] xhci-hcd xhci-hcd.0.auto: irq 72, io mem 0xfe900000
[    1.413086] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[    1.413102] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.413115] usb usb3: Product: xHCI Host Controller
[    1.413127] usb usb3: Manufacturer: Linux 4.19.111 xhci-hcd
[    1.413139] usb usb3: SerialNumber: xhci-hcd.0.auto
[    1.413487] hub 3-0:1.0: USB hub found
[    1.413528] hub 3-0:1.0: 1 port detected
[    1.413784] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    1.413920] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 4
[    1.413936] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[    1.413995] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    1.414091] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.19
[    1.414106] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.414118] usb usb4: Product: xHCI Host Controller
[    1.414129] usb usb4: Manufacturer: Linux 4.19.111 xhci-hcd
[    1.414141] usb usb4: SerialNumber: xhci-hcd.0.auto
[    1.414461] hub 4-0:1.0: USB hub found
[    1.414500] hub 4-0:1.0: 1 port detected
[    1.414838] usbcore: registered new interface driver cdc_acm
[    1.414853] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.414901] usbcore: registered new interface driver usblp
[    1.414941] usbcore: registered new interface driver cdc_wdm
[    1.414984] usbcore: registered new interface driver uas
[    1.415060] usbcore: registered new interface driver usb-storage
[    1.415100] usbcore: registered new interface driver ums-alauda
[    1.415138] usbcore: registered new interface driver ums-cypress
[    1.415176] usbcore: registered new interface driver ums-datafab
[    1.415211] usbcore: registered new interface driver ums_eneub6250
[    1.415248] usbcore: registered new interface driver ums-freecom
[    1.415285] usbcore: registered new interface driver ums-isd200
[    1.415323] usbcore: registered new interface driver ums-jumpshot
[    1.415360] usbcore: registered new interface driver ums-karma
[    1.415392] usbcore: registered new interface driver ums-onetouch
[    1.415429] usbcore: registered new interface driver ums-sddr09
[    1.415466] usbcore: registered new interface driver ums-sddr55
[    1.415502] usbcore: registered new interface driver ums-usbat
[    1.415591] usbcore: registered new interface driver usbserial_generic
[    1.415613] usbserial: USB Serial support registered for generic
[    1.415651] usbcore: registered new interface driver option
[    1.415676] usbserial: USB Serial support registered for GSM modem (1-port)
[    1.415816] usbcore: registered new interface driver trancevibrator
[    1.416159] usbcore: registered new interface driver xpad
[    1.416203] usbcore: registered new interface driver usb_acecad
[    1.416244] usbcore: registered new interface driver aiptek
[    1.416284] usbcore: registered new interface driver gtco
[    1.416323] usbcore: registered new interface driver hanwang
[    1.416361] usbcore: registered new interface driver kbtab
[    1.416927] .. rk pwm remotectl v1.1 init
[    1.417115] input: ff420030.pwm as /devices/platform/ff420030.pwm/input/input0
[    1.417497] sensor_register_slave:kxtj9,id=11
[    1.417513] sensor_register_slave:mma8452,id=17
[    1.417524] sensor_register_slave:lis3dh,id=7
[    1.417535] sensor_register_slave:mma7660,id=18
[    1.417543] sensor_register_slave:gs_mxc6655xa,id=24
[    1.417550] sensor_register_slave:lsm303d,id=26
[    1.417558] sensor_register_slave:gs_mc3230,id=27
[    1.417586] [Gsensor]   gsensor_init
[    1.417599] sensor_register_slave:mpu6880_acc,id=28
[    1.417611] sensor_register_slave:mpu6500_acc,id=29
[    1.417622] sensor_register_slave:lsm330_acc,id=30
[    1.417632] sensor_register_slave:bma2xx_acc,id=31
[    1.417644] sensor_register_slave:akm8975,id=35
[    1.417654] sensor_register_slave:akm8963,id=36
[    1.417665] sensor_register_slave:l3g4200d,id=50
[    1.417676] sensor_register_slave:l3g20d,id=51
[    1.417687] sensor_register_slave:ewtsa,id=52
[    1.417699] sensor_register_slave:lsm330_gyro,id=56
[    1.417710] sensor_register_slave:cm3217,id=58
[    1.417721] sensor_register_slave:cm3218,id=59
[    1.417732] sensor_register_slave:ls_stk3410,id=67
[    1.417743] sensor_register_slave:ps_stk3410,id=72
[    1.418312] i2c /dev entries driver
[    1.419385] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
[    1.419414] fan53555-reg: supplied by vcc_sys
[    1.421063] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected!
[    1.421089] fan53555-reg: supplied by vcc5v0_sys
[    1.422678] rk808 0-001b: chip id: 0x0
[    1.426139] rk808-regulator rk808-regulator: there is no dvs0 gpio
[    1.426198] rk808-regulator rk808-regulator: there is no dvs1 gpio
[    1.426249] DCDC_REG1: supplied by vcc3v3_sys
[    1.427130] DCDC_REG2: supplied by vcc3v3_sys
[    1.427727] DCDC_REG3: supplied by vcc3v3_sys
[    1.427966] DCDC_REG4: supplied by vcc3v3_sys
[    1.428450] LDO_REG1: supplied by vcc3v3_sys
[    1.429186] LDO_REG2: supplied by vcc3v3_sys
[    1.429680] LDO_REG3: supplied by vcc3v3_sys
[    1.430287] LDO_REG4: supplied by vcc3v3_sys
[    1.430904] LDO_REG5: supplied by vcc3v3_sys
[    1.431391] LDO_REG6: supplied by vcc3v3_sys
[    1.431998] LDO_REG7: supplied by vcc3v3_sys
[    1.432480] LDO_REG8: supplied by vcc3v3_sys
[    1.433092] SWITCH_REG1: supplied by vcc3v3_sys
[    1.433419] SWITCH_REG2: supplied by vcc3v3_sys
[    1.433891] rk808-rtc rk808-rtc: device is disabled
[    1.433915] rk808-rtc: probe of rk808-rtc failed with error -22
[    1.434155] rtc-hym8563 0-0051: could not init device, -6
[    1.435385] usbcore: registered new interface driver uvcvideo
[    1.435402] USB Video Class driver (1.1.1)
[    1.435719] rockchip-iodomain ff320000.syscon:io-domains: Linked as a consumer to regulator.26
[    1.435933] rockchip-iodomain ff770000.syscon:io-domains: Linked as a consumer to regulator.26
[    1.435997] rockchip-iodomain ff770000.syscon:io-domains: Linked as a consumer to regulator.25
[    1.436059] rockchip-iodomain ff770000.syscon:io-domains: Linked as a consumer to regulator.22
[    1.436876] __power_supply_register: Expected proper parent device for 'test_ac'
[    1.437005] __power_supply_register: Expected proper parent device for 'test_battery'
[    1.437185] thermal thermal_zone2: power_allocator: sustainable_power will be estimated
[    1.437257] __power_supply_register: Expected proper parent device for 'test_usb'
[    1.438813] rockchip-thermal ff260000.tsadc: tsadc is probed successfully!
[    1.439320] device-mapper: uevent: version 1.0.3
[    1.439546] device-mapper: ioctl: 4.39.0-ioctl (2018-04-03) initialised: dm-devel@redhat.com
[    1.439744] device-mapper: verity-avb: AVB error handler initialized with vbmeta device:
[    1.439760] Bluetooth: HCI UART driver ver 2.3
[    1.439773] Bluetooth: HCI UART protocol H4 registered
[    1.439785] rtk_btusb: RTKBT_RELEASE_NAME: 20200330_BT_ANDROID_10.0
[    1.439795] rtk_btusb: Realtek Bluetooth USB driver module init, version 5.2.1
[    1.439805] rtk_btusb: Register usb char device interface for BT driver
[    1.439987] usbcore: registered new interface driver rtk_btusb
[    1.440202] cpu cpu0: bin=1
[    1.440235] cpu cpu0: leakage=28
[    1.440316] cpu cpu0: Linked as a consumer to regulator.16
[    1.452103] cpu cpu0: temp=34444, pvtm=151537 (152342 + -805)
[    1.452281] cpu cpu0: pvtm-volt-sel=2
[    1.452331] cpu cpu0: Dropping the link to regulator.16
[    1.452356] cpu cpu0: bin-scale=34
[    1.452407] cpu cpu4: bin=1
[    1.452436] cpu cpu4: leakage=50
[    1.452524] cpu cpu4: Linked as a consumer to regulator.13
[    1.464470] cpu cpu4: temp=33888, pvtm=155597 (156165 + -568)
[    1.464565] cpu cpu4: pvtm-volt-sel=2
[    1.464621] cpu cpu4: Dropping the link to regulator.13
[    1.464649] cpu cpu4: bin-scale=17
[    1.464879] cpu cpu0: Linked as a consumer to regulator.16
[    1.464921] cpu cpu0: Dropping the link to regulator.16
[    1.465031] cpu cpu0: Linked as a consumer to regulator.16
[    1.465531] cpu cpu0: avs=0
[    1.465756] cpu cpu0: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[    1.466316] cpu cpu0: failed to find power_model node
[    1.466454] cpu cpu4: Linked as a consumer to regulator.13
[    1.467140] cpu cpu4: avs=0
[    1.467187] energy_model: pd4: hertz/watts ratio non-monotonically decreasing: em_cap_state 2 >= em_cap_state1
[    1.467383] cpu cpu4: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[    1.469120] cpu cpu4: failed to find power_model node
[    1.470350] sdhci: Secure Digital Host Controller Interface driver
[    1.470370] sdhci: Copyright(c) Pierre Ossman
[    1.470381] Synopsys Designware Multimedia Card Interface Driver
[    1.471048] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
[    1.471257] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
[    1.471285] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
[    1.471342] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 28,32 bit host data width,256 deep fifo
[    1.471486] dwmmc_rockchip fe310000.dwmmc: allocated mmc-pwrseq
[    1.471505] mmc_host mmc0: card is non-removable.
[    1.484702] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    1.498178] dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode.
[    1.498748] dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller.
[    1.498780] dwmmc_rockchip fe320000.dwmmc: Version ID is 270a
[    1.498831] dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 29,32 bit host data width,256 deep fifo
[    1.498931] dwmmc_rockchip fe320000.dwmmc: Linked as a consumer to regulator.9
[    1.498994] dwmmc_rockchip fe320000.dwmmc: Linked as a consumer to regulator.22
[    1.512486] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    1.520000] mmc0: queuing unknown CIS tuple 0x80 (2 bytes)
[    1.522676] mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
[    1.525675] mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
[    1.526374] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.530105] mmc0: queuing unknown CIS tuple 0x80 (7 bytes)
[    1.553678] mmc2: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA
[    1.554953] hidraw: raw HID events driver (C) Jiri Kosina
[    1.557653] usbcore: registered new interface driver usbhid
[    1.557677] usbhid: USB HID core driver
[    1.558500] ashmem: initialized
[    1.561382] rockchip-saradc ff100000.saradc: Linked as a consumer to regulator.7
[    1.562146] optee: probing for conduit method from DT.
[    1.562172] optee: revision 1.1
[    1.562518] optee: initialized driver
[    1.562535] rknandbase v1.2 2018-05-08
[    1.562977] usbcore: registered new interface driver snd-usb-audio
[    1.568364] netem: version 1.3
[    1.568391] u32 classifier
[    1.568401]     Actions configured
[    1.569239] xt_time: kernel timezone is -0000
[    1.569388] gre: GRE over IPv4 demultiplexor driver
[    1.569399] IPv4 over IPsec tunneling driver
[    1.570284] Initializing XFRM netlink socket
[    1.570321] IPsec XFRM device driver
[    1.570748] NET: Registered protocol family 10
[    1.571828] Segment Routing with IPv6
[    1.571933] mip6: Mobile IPv6
[    1.572714] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    1.573602] NET: Registered protocol family 17
[    1.573633] NET: Registered protocol family 15
[    1.573695] Bridge firewalling registered
[    1.574032] Bluetooth: RFCOMM TTY layer initialized
[    1.574054] Bluetooth: RFCOMM socket layer initialized
[    1.574092] Bluetooth: RFCOMM ver 1.11
[    1.574113] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    1.574126] Bluetooth: BNEP filters: protocol multicast
[    1.574141] Bluetooth: BNEP socket layer initialized
[    1.574151] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    1.574164] Bluetooth: HIDP socket layer initialized
[    1.574211] l2tp_core: L2TP core driver, V2.0
[    1.574230] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[    1.574242] [BT_RFKILL]: Enter rfkill_rk_init
[    1.574252] [WLAN_RFKILL]: Enter rfkill_wlan_init
[    1.574653] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[    1.574676] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = rtl8723du
[    1.574689] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[    1.574701] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[    1.574771] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[    1.574783] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[    1.574796] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[    1.575254] sensor_register_slave:mpu6500_gyro,id=54
[    1.575269] sensor_register_slave:mpu6880_gyro,id=55
[    1.576903] registered taskstats version 1
[    1.576920] Loading compiled-in X.509 certificates
[    1.577181] Key type ._fscrypt registered
[    1.577201] Key type .fscrypt registered
[    1.577217] Key type fscrypt-provisioning registered
[    1.577531] pstore: Using compression: deflate
[    1.578464] rga2: Driver loaded successfully ver:3.02
[    1.578737] rga2: Module initialized.
[    1.590754] mmc2: new HS400 MMC card at address 0001
[    1.592062] mmcblk2: mmc2:0001 MMC8GB 7.28 GiB
[    1.592844] mmcblk2boot0: mmc2:0001 MMC8GB partition 1 4.00 MiB
[    1.593621] mmcblk2boot1: mmc2:0001 MMC8GB partition 2 4.00 MiB
[    1.593954] mmcblk2rpmb: mmc2:0001 MMC8GB partition 3 4.00 MiB, chardev (237:0)
[    1.599899]  mmcblk2: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17
[    1.618510] mali ff9a0000.gpu: Linked as a consumer to regulator.14
[    1.618614] mali ff9a0000.gpu: leakage=40
[    1.633160] mali ff9a0000.gpu: temp=33333, pvtm=127995 (128363 + -368)
[    1.634740] mali ff9a0000.gpu: pvtm-volt-sel=2
[    1.635321] mali ff9a0000.gpu: avs=0
[    1.636209] mali ff9a0000.gpu: GPU identified as 0x0860 r2p0 status 0
[    1.636610] mali ff9a0000.gpu: Protected mode not available
[    1.637056] mali ff9a0000.gpu: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[    1.637168] mali ff9a0000.gpu: Using configured power model mali-simple-power-model, and fallback mali-simple-power-model
[    1.637292] I : [File] : drivers/gpu/arm/midgard/backend/gpu/mali_kbase_devfreq.c; [Line] : 417; [Func] : kbase_devfreq_init(); success initing power_model_simple.
[    1.638143] mali ff9a0000.gpu: Probed as mali0
[    1.639383] rockchip-dmc dmc: Linked as a consumer to regulator.15
[    1.639499] rockchip-dmc dmc: Failed to get leakage
[    1.639547] rockchip-dmc dmc: Failed to get pvtm
[    1.639980] rockchip-dmc dmc: avs=0
[    1.640178] rockchip-dmc dmc: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0 h_table=0
[    1.640210] rockchip-dmc dmc: could not find power_model node
[    1.646510] hctosys: unable to open rtc device (rtc0)
[    1.647471] It doesn't contain Rogue gpu
[    1.647964] rockchip_headset rk-headset: Can not read property hook_gpio
[    1.647993] rockchip_headset rk-headset: headset have hook adc mode
[    1.648242] input: rk-headset as /devices/platform/rk-headset/input/input1
[    1.652022] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    1.654011] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    1.654642] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 417; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '15:32:09', on 'Sep  9 2021'.
[    1.655054] Mali:
[    1.655056] Mali device driver loaded
[    1.655435] input: rk29-keypad as /devices/platform/rockchip-key/input/input2
[    1.655702] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    1.655721] cfg80211: failed to load regulatory.db
uρ  1.667553]
[    1.667908] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[    1.674796] mmc0: new high speed SDIO card at address 0001
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

友情链接 : 爱板网 电子发烧友论坛 云汉电子社区 粤ICP备14022046号-2
快速回复 返回顶部 返回列表