Firefly开源社区

求助 : Firefly-RK3288 mipi chip is not found 問題

114

积分

0

威望

0

贡献

技术小白

积分
114
发表于 2022-2-18 11:28:28     
本帖最后由 EdgeHH 于 2022-2-23 14:21 编辑

目前設置MIPI 點屏時發現MIPI DSI CHIP IS NOT FOUND (串口資料記錄如下)



Use mipi_lc d as ext end screen


[     0.61382 9] rk32-dsi


[     0.613950] rk32_mipi_dsi_probe: 1840:dsi ->host.irq =51


[    0.6 13968] mipi dsi  chip is  not found, read  id:ffffffff, but 3133302 a is correct


[    0.613981] rk32-mipi ff960000.mipi: rk  mipi_dsi probe fail!


[     0.61 3993] rk32-mipi  ff960000 .mipi: rockchip mipi_dsi  v1.1 2014-06-17


[    0 .614022]  rk32-mipi: probe of ff960000.mipi failed with error -1


程式架構(有補丁)是基於雙屏運用,eDP+lvds 可以正常點屏,但eDP+MIPI or LVDS+MIPI, 此時MIPI沒有輸出 (mipi dsi chip is not found),
論壇大神們有遇過此問題嗎?這樣的問題應該朝什麼方向來處理or 修改程式呢? 麻煩各位大神指導指導~ 謝謝!
各位論壇大神可否提供 可以正常作動(雙屏) for mipi 屏的LCD-Dual-xxx.dtsi 和 rk32_mipi_dsi.c 讓我參考比對 (我的設定檔如附檔),是否我的設定有問題

rk32_mipi_dsi.zip

10.56 KB, 下载次数: 0, 下载积分: 灯泡 -1 , 经验 -1

lcd-dual-KD070D57-mipi-600x1024.zip

1.63 KB, 下载次数: 0, 下载积分: 灯泡 -1 , 经验 -1

回复

使用道具 举报

114

积分

0

威望

0

贡献

技术小白

积分
114
发表于 2022-2-23 10:49:41     
請教各位大神,mipi dsi  chip is  not found

這是指找不到MIPI 屏的controller ??  還是Firefly-RK3288  ff960000 ??

目前一直卡在這裡,可否那位前輩指點指點一下迷津~~ 謝謝!
回复

使用道具 举报

114

积分

0

威望

0

贡献

技术小白

积分
114
发表于 2022-2-23 10:54:01     
以下是我的 設定 lcd-dual-KD070D57-mipi-600x1024.dtsi

// /{
  /* about mipi */
  //----------MIPI DSI port signal initializtion----------------------------
  //disp_mipi_init: mipi_dsi_init{
            mipi_dsi_init{
                          compatible = "rockchip,mipi_dsi_init";
                          rockchip,screen_init        = <1>;//0: no init;1:have init
                          rockchip,dsi_lane                = <4>;
                          rockchip,dsi_hs_clk                = <389>;  
                          rockchip,mipi_dsi_num        = <1>;
  };
  
  //disp_mipi_power_ctr: mipi_power_ctr {
            mipi_power_ctr {
                                        compatible = "rockchip,mipi_power_ctr";
                                        mipi_lcd_rst:mipi_lcd_rst{
                                                        compatible = "rockchip,lcd_rst";

                                                        rockchip,gpios = <&gpio7 GPIO_B1 GPIO_ACTIVE_HIGH>; // hi lo hi //Header_B pin15
                                                        rockchip,delay = <300>;//10
                                        };
                        /*                mipi_lcd_en:mipi_lcd_en {
                                                        compatible = "rockchip,lcd_en";
                                                        rockchip,gpios = <&gpio7 GPIO_A3 GPIO_ACTIVE_HIGH>;
                                                        rockchip,delay = <100>;//10
                                        };*/

                };

//  ///## 屏初始化序列////////////////////////////
  //disp_mipi_init_cmds: screen-on-cmds {
            screen-on-cmds {
          //  rockchip,cmd_debug = <0>;
                          compatible = "rockchip,screen-on-cmds";
                          rockchip,cmd_debug = <1>;



//sleep out                       

          rockchip,on-cmds1 {
                        compatible = "rockchip,on-cmds";
                        rockchip,cmd_type =  <LPDT>;// <HSDT>;//命令是在 low power(LPDT)还是 high speed(HSDT)下发送
                        rockchip,dsi_id = <0>;//0:0  1:1  2:0&1
                        //rockchip,cmd = <0x05 0x11>;
                        rockchip,cmd = <0x05 dcs_exit_sleep_mode>; //drivers/video/rockchip/transmitter/mipi_dsi.h
                        rockchip,cmd_delay = <150>;  //150
        };

//display on
          rockchip,on-cmds2 {
                compatible = "rockchip,on-cmds";
                        rockchip,cmd_type = <LPDT>;
                        rockchip,dsi_id = <0>;
                        //rockchip,cmd = <0x05 0x29>;
                        rockchip,cmd = <0x05 dcs_set_display_on>;  //drivers/video/rockchip/transmitter/mipi_dsi.h
                        rockchip,cmd_delay = <10>;//100  10ms
        };
////////////////////////////               
  };

   //-----------timing setting for LCM MIPI T-CON ----------------
  //disp_timings: display-timings {
         display-timings {
          native-mode = <&KD070D57>;
//           native-mode = <&timing0>;
          compatible = "rockchip,display-timings";
          KD070D57: timing0 {
//          timing0: timing0 {
                screen-type = <SCREEN_MIPI >;//1:<SCREEN_MIPI>;2:<SCREEN_DUAL_MIPI>
                lvds-format = <LVDS_8BIT_2>;//don't care
                          out-face    = <OUT_P888>;
                //color-mode = <COLOR_RGB>;
                          // OUT_P888:24bit //配置颜色,可为OUT_P888(24位)、OUT_P666(18位)或者OUT_P565(16位)
                           clock-frequency = <144717300>;
                          hactive = <600>;                                                  
                          hsync-len = <1>;//16  10             <12
                          hback-porch = <60>; //16 35   =hfp
                          hfront-porch = <80>;//32 210   = hsw +hbp    l shift
                         
                          vactive = <1024>;///1280
                          vsync-len = <1>; //4
                          vback-porch = <25>;//8 ok6
                          vfront-porch = <35>;//16 ok
                         
                          hsync-active = <0>;//hync 极性控制 置 1 反转极性
                          vsync-active = <0>;
                          de-active = <0>;
                          pixelclk-active = <0>;
                          swap-rb = <0>;
                          swap-rg = <0>;
                          swap-gb = <0>;
  
                                };
                };
               

               
//};
回复

使用道具 举报

114

积分

0

威望

0

贡献

技术小白

积分
114
发表于 2022-2-23 14:27:14     
本帖最后由 EdgeHH 于 2022-2-23 14:34 编辑

開機時完整的串口記錄:

[  233.3 42078] c pufreq: cpufreq:  reboot  set core rate=12 00000000 , volt=1 100000

[  233.342101] m ali_reboot_notifier_even t enter

[  233. 342109] mali_reb oot_notifier_eve nt exit

[  233.342288] mmcblk m mc0:0001: Unbalanced pm_ runtime_ enable!

[  233.9 57375] Chenzy--- ----hkw- ------es8323_i2c _shutdown

[  234.0 61978] dwc_otg_d river_shutdown:  disconnect USB d evice mode

[  234.0 71756] Restartin g system  with command 'l oader'.
DR Vers ion 1.00 2015031 8

In

SRX

Chan nel a: DDR3  200MHz

Bus Widt h=32 Col=10 Bank=8 Row=1 5 CS=1 Die Bus-W idth=16 Size=102 4MB

Channel b:  DDR3 200MHz

Bus Widt h=32 Col =10 Bank=8 Row=1 5 CS=1 D ie Bus-W idth=16 Size=102 4MB

OUT





U-Bo ot 2014.10-RK328 8-10-g65 679f1 (J ul 20 20 15 - 10: 28:11)



CPU: r k3288

CPU's clock infor mation:

    arm  pll = 6 00000000HZ

     periph pll = 300 000000HZ

    dd r pll =  200000000HZ

     codec p ll = 594000000HZ

Board:         Rockchi p platform Board

DRAM:   Found dram bank s:1

Add ing bank:0000000 00000000 0(00000000800000 00)

128  MiB

remotectl v0.1

storage  init OK!

Using  default  environm ent



G etParam

check p arameter  success

failed t o prepar e fdt fr om boot!

power ke y: bank- 0 pin-5

can't fi nd dts node for  ricoh619

pmic:act 8846

Can't fi nd dts node for  fuel guage cw201 x

Secur eBootEn = 0, Sec ureBootLock = 0



#Boot  ver: 2015-07-20#2.19

empty ser ial no.

reboot to rocku sb.

DDR Vers ion 1.00  2015031 8

In

S RX

Chan nel a: D DR3  200MHz

Bus Widt h=32 Col =10 Bank =8 Row=1 5 CS=1 D ie Bus-W idth=16  Size=102 4MB

Cha nnel b:  DDR3  200MHz

Bus Widt h=32 Col =10 Bank =8 Row=1 5 CS=1 D ie Bus-W idth=16  Size=102 4MB

OUT





U-Bo ot 2014. 10-RK328 8-10-g65 679f1 (J ul 20 20 15 - 10: 28:11)



CPU: r k3288

CPU's clo ck infor mation:

    arm  pll = 6 00000000HZ

     periph p ll = 300 000000HZ

    dd r pll =  200000000HZ

     codec p ll = 594000000HZ

Board:         Rockchi p platform Board

DRAM:   Found dram bank s:1

Add ing bank:0000000 00000000 0(00000000800000 00)

128  MiB

remotect l v0.1

storage  init OK!

Using  default  environm ent



G etParam

check p arameter  success

failed t o prepar e fdt fr om boot!

power ke y: bank-0 pin-5

can't fi nd dts node for  ricoh619

pmic:act 8846

Can't fi nd dts node for  fuel guage cw201 x

SecureBootEn  = 0, SecureBootL ock = 0



#Boot ver: 20 15-07-20#2.19

empty ser ial no.

reboot to rocku sb.

DDR Vers ion 1.00 20150318

In

S RX

Channel a: DDR3  200MHz

Bus Width=32 Col =10 Bank=8 Row=15 CS=1 Die Bus-W idth=16 Size=1024MB

Cha nnel b: DDR3 200MHz

Bus Widt h=32 Col=10 Bank=8 Row=15 CS=1 D ie Bus-Width=16 Size=102 4MB

OUT





U-Bo ot 2014.10-RK3288-10-g65679f1 (Jul 20 2015 - 10: 28:11)



CPU: r k3288

CPU's clock information:

    arm pll = 6 00000000HZ

    periph pll = 300 000000HZ

    ddr pll = 200000000HZ

    codec p ll = 594000000HZ

Board:        Rockchip platfo rm Board

DRAM:  Found dram banks:1

Adding bank:0000000 000000000(0000000080000000)

128  MiB

remotect l v0.1

storage  init OK!

Using  default environment



GetParam

check parameter success

failed to prepar e fdt from boot!

power ke y: bank-0 pin-5

can't fi nd dts node for ricoh619

pmic:act 8846

Can't fi nd dts node for fuel gua ge cw201x

SecureBootEn  = 0, SecureBootLock = 0



#Boot  ver: 2015-07-20#2.19

empty serial no.

checkKe y

vbus = 1

board_fbt_key_pressed: ir_k eycode = 0x0, frt = 0

no fuel gauge fou nd

no fuel gauge found

read log o_on switch from  dts [0]

no fue l gauge found

checkKey

vbus =  1

board_fbt_key_pressed: ir_keycode = 0 x0, frt = 0

got recovery cmd from misc.

load fdt  from resouce.

ERROR: [get_entry_ram]:  Cannot f ind logo_kernel. bmp!

Secure B oot state: 0

kernel   @  0x02000000 (0x006a6e80)

ramdisk  @ 0x05bf0000  (0x002c6ad4)

bootrk: do_bootm_l inux...

   Loading Devi ce Tree to 05600000, end  0561c8c5 ...  OK

Add bank :000000000000000 0, 0000000080000 000



Starti ng kernel ...



[    0.0 00000] Booting Linux on  physical CPU 0x5 00

[    0.00000 0] Initializing cgroup subsys cp u

[    0.000000] Initia lizing cgroup subsys cpuacct

[     0.000000] Linux version 3.10.0 (user@ ubuntu) (gcc version 4.6.x-googl e 20120106 (prerelease)  (GCC) ) #925 SMP PREEMPT  Thu Jan 20 15:59:08 CST 2022

[    0.000000] CP U: ARMv7 Processor [410fc0d1] re vision 1 (ARMv7), cr=10c 5387d

[     0.000000] CPU: PIPT  / VIPT nonaliasi ng data  cache, V IPT aliasing ins truction  cache

[    0.0 00000] Machine: Rockchip  RK3288  (Flattened Devic e Tree),  model:  rockchip,rk3288

[    0. 000000] rockchip_uboot_l ogo_setup: mem:  0x020000 00@0x7dc00000, o ffset:0x 00000000

[    0.000000]  hdmi in it vic is -1

[     0.000000] rockchip_ub oot_mem_ reserve:  reserve 0x02000 000@0x7d c00000 for uboot  logo

[     0.000000] ro ckchip_i on_reserve

[     0.000000] ion h eap(drm): base(0 ) size(0 ) align(0)

[     0.00000 0] ion heap(cma) : base(0 ) size(28000000)  align(0 )

[     0.000000] ion heap(vmall oc): base(0) siz e(0) ali gn(0)

[    0.00 0000] cm a: CMA: reserved  640 MiB  at 55c0 0000

[    0.000 000] ion_reserve: cma re served b ase 55c00000 siz e 671088 640

[    0.0000 00] cma:  CMA: re served 16 MiB at  1f00000 0

[    0.000000 ] Memory  policy: ECC dis abled, D ata cach e writealloc

[     0.000000] Boot mode:  RECOVERY  (2) flag: RECOV ER (0xc3 524203)

[    0. 000000]  PERCPU: Embedded  9 pages /cpu @c1 f1f000 s13376 r8 192 d152 96 u36864

[     0.000000 ] Built 1 zoneli sts in Z one orde r, mobility grou ping on.   Total pages: 5 23264

[     0.000000] Ke rnel com mand line: vmall oc=496M  console= ttyS2 androidboo t.selinu x=permissive and roidboot .hardware=rk30bo ard andr oidboot.console= ttyS2 in it=/init   mtdparts=rk29x xnand:0x 00002000@0x00000 000(para meter),0x0000200 0@0x0000 2000(uboot),0x00 002000@0 x0000400 0(misc),0x000080 00@0x000 06000(resource), 0x000080 00@0x0000e000(ke rnel),0x 00010000@0x00016 000(boot ),0x0001 0000@0x00026000( recovery ),0x0001a000@0x0 0036000( backup),0x000400 00@0x000 50000(ca che),0x00002000@ 0x000900 00(kpanic),0x003 00000@0x 00092000(system) ,0x00008 000@0x00392000(m etadata) ,0x00002 000@0x0039A000(b aseparam er),0x00200000@0 x0039C00 0(userdata),0x00 020000@0 x0059C000(radica l_update ),-@0x00 5BC000(user) sto ragemedi a=emmc uboot_log o=0x0200 0000@0x7dc00000  loader.t imestamp=2015-07 -20_10:2 8:11 hdm i.vic=-1

[    0 .000000]  PID hash table  entries:  2048 (order: 1,  8192 by tes)

[    0.000 000] Den try cach e hash table ent ries: 65 536 (order: 6, 2 62144 by tes)

[    0.000 000] Ino de-cache  hash table entr ies: 327 68 (order: 5, 13 1072 byt es)

[    0.0000 00] allo cated 4194304 by tes of p age_cgro up

[    0.00000 0] pleas e try 'cgroup_di sable=me mory' option if  you don' t want memory cg roups

[     0.00 0000] Memory: 20 48MB = 2 048MB total

[     0.0000 00] Memory: 1353 140k/135 3140k available,  744012k  reserve d, 884736K highm em

[     0.000000] Virtu al kerne l memory layout:

[    0 .000000]     vector  : 0 xffff000 0 - 0xffff1000    (   4 k B)

[    0.000000]     f ixmap  : 0xfff00 000 - 0x fffe0000   ( 896  kB)

[     0.000000]     vmalloc  : 0xe08 00000 - 0xff0000 00   ( 488 MB)

[    0.0 00000]      lowmem  : 0xc 0000000  - 0xe000 0000   ( 512 MB)

[    0 .000000]     pkm ap   : 0 xbfe00000 - 0xc0 000000    (   2 MB)

[    0.00000 0]     m odules : 0xbf000 000 - 0x bfe00000   (  14 MB)

[     0.000000]        .text  : 0xc00 08000 - 0xc0bb5c 70   (11960 kB)

[    0. 000000]        .init : 0x c0bb6000  - 0xc0c0f440    ( 358 kB)

[     0.000000]        .data :  0xc0c10000 - 0xc 0da21c0    (1609 kB)

[    0.0000 00]        .bss  : 0xc0da 21c0 - 0 xc0ec387c   (115 8 kB)

[    0.000000] SL UB: HWal ign=64, Order=0- 3, MinOb jects=0, CPUs=4,  Nodes=1

[    0 .000000] Preempt ible hie rarchical RCU im plementa tion.

[    0.00 0000]         RCU dyntick-idle  grace-pe riod acceleration is ena bled.

[     0.000000] NR_IRQS:16  nr_irqs:16 16

[    0.000000] r k_clk_tree_init  start!

[    0.000000] r kclk: _r kclk_add_provider: fail  to get ehci1phy_ 12m_div

[    0.000000] rkclk: r kclk_cache_parents: ehci 1phy_12m _div clk_get error

[     0.000000] rk_ge t_uboot_display_flag: uboot_logo _on = 0

[    0.000000]  rkclk_in it_clks: cnt_parent = 7

[    0.000000]  rkclk_init_clks:  cnt_rate = 29

[    0.0 00000] rk3288 se t GPLL BW 20 for HDMI!

[    0.000000] Architect ed cp15  timer(s)  running at 24.00MHz (ph ys).

[    0.000 000] Switching to timer- based de lay loop

[    0 .000000] sched_c lock: ARM arch t imer >56  bits at 24000kH z, resolution 41ns

[     0.00000 0] process version: 0

[     0.00 0000] channel:0,  lkg:18

[    0.000000]  target-t emp:80

[    0.000000] c hannel:2 , lkg:0

[    0. 000000] channel:0, lkg:1 8

[     0.000000] channel:1, lkg :12

[    0.0000 00] sched_clock:  32 bits at 100  Hz, reso lution 10000000n s, wraps every 429496728 6ms

[     0.345053] Calibrating  delay lo op (skipped), va lue calc ulated using tim er frequ ency.. 48.00 BogoMIPS (l pj=240000)

[     0.345068] pid_m ax: default: 327 68 minim um: 301

[    0.345183]  Security Framewo rk initi alized

[    0.3 45200] SELinux:   Initializing.

[    0.3 45272] Mount-cac he hash  table entries: 5 12

[     0.345913] Initializing  cgroup s ubsys debug

[     0.3459 27] Initializing  cgroup  subsys memory

[     0.345952] In itializing cgrou p subsys  freezer

[    0 .345980]  CPU: Testing wr ite buff er coherency: ok

[    0 .346293] /cpus/cpu@0 mis sing clo ck-frequency pro perty

[     0.346306] /c pus/cpu@ 1 missing clock- frequenc y proper ty

[    0.34631 5] /cpus/cpu@2 missing c lock-fre quency property

[    0. 346325] /cpus/cpu@3 miss ing cloc k-frequency prop erty

[     0.346380] CPU0: threa d -1, cpu 0, soc ket 5, m pidr 80000500

[     0.346430] Se tting up static  identity  map for 0xc086b db0 - 0x c086be08

[    0 .349553] last_lo g: 0x1e900000 ma p to 0xe 0804000 and copy  to 0xe0 886000, size 0x8 0000 ear ly 0x1879 (versi on 3.1)

[    0. 423189] CPU1: Bo oted sec ondary processor

[    0 .423222] CPU1: thread -1 , cpu 1, socket  5, mpidr  8000050 1

[    0.442860 ] CPU2: Booted secondary  process or

[    0.44288 4] CPU2:  thread -1, cpu 2, socke t 5, mpi dr 80000502

[     0.4625 68] CPU3: Booted  seconda ry processor

[     0.462591] CPU3: threa d -1, cp u 3, soc ket 5, mpidr 800 00503

[     0.462693] Brought up  4 CPUs

[    0. 462722]  SMP: Total of 4  processo rs activ ated (192.00 Bog oMIPS).

[    0.462731]  CPU: All  CPU(s) started  in SVC m ode.

[     0.463461] devtmpfs: i nitialized

[     0.46772 8] VFP support v 0.3: imp lementor 41 arch itecture  3 part  30 variant d rev  0

[    0.468826] pinct rl core:  initialized pin ctrl sub system

[    0.4 69073] regulator -dummy: no param eters

[     0.493628] NE T: Regis tered protocol f amily 16

[    0.495492]  DMA: pr eallocat ed 256 KiB pool  for atom ic coherent allo cations

[    0.495815]  ion_snap shot: 0x1ea98000  map to  0xe09070 00 and copy to 0 xc0e9eb4 c (version 0.1)

[    0.496041] Register ed FIQ tty driver

[     0.496435] fiq-de bugger is disabl ed in de vice tree

[     0.497131] rockchip_get_b ank_data :name=ba se start=0xff750 000,end= 0xff7500ff

[     0.497153] rockchip_get_ bank_dat a:name=mux_bank0  start=0 xff73008 4,end=0xff73008f

[    0 .497171] rockchip_get_ba nk_data:name=pul l_bank0  start=0xff730064 ,end=0xf f73006f

[    0.497187] rockchip _get_bank_data:n ame=drv_ bank0 start=0xff 730070,e nd=0xff73007b

[    0.49 7282] ro ckchip_get_bank_ data:nam e=/pinctrl@ff770 000/gpio 1@ff780000 start =0xff780000,end=0xff7800 ff

[     0.497350] rockchip_get_ bank_dat a:name=/pinctrl@ ff770000 /gpio2@ff790000  start=0x ff790000,end=0xf f7900ff

[    0. 497413] rockchip _get_ban k_data:name=/pinctrl@ff7 70000/gpio3@ff7a 0000 sta rt=0xff7 a0000,end=0xff7a 00ff

[    0.497477] roc kchip_ge t_bank_data:name =/pinctr l@ff770000/gpio4@ff7b000 0 start= 0xff7b0000,end=0 xff7b00f f

[    0.497539] rockch ip_get_bank_data :name=/p inctrl@ff770000/ gpio5@ff 7c0000 start=0xff7c0000, end=0xff 7c00ff

[    0.4 97602] rockchip_get_bank _data:na me=/pinctrl@ff77 0000/gpi o6@ff7d0000 start=0xff7d 0000,end =0xff7d00ff

[     0.4976 65] rockchip_get_bank_da ta:name=/pinctrl @ff77000 0/gpio7@ ff7e0000 start=0 xff7e000 0,end=0xff7e00ff

[    0.497728] rockchi p_get_ba nk_data:name=/pi nctrl@ff 770000/g pio8@ff7f0000 start=0xff 7f0000,end=0xff7 f00ff

[    0.497798] ro ckchip_g et_bank_ data:name=/pinctrl@ff770 000/gpio15@ff7f2 000 star t=0xff7f2000,end =0xff7f2 0ff

[    0.497863] rock chip_pin ctrl_probe:name= RK3288-G PIO,type=3

[     0.497877] rockchip_pinc trl_prob e:name=base star t=0xff77 0000,end =0xff77013f

[     0.497889] rockchip_pin ctrl_pro be:name=pull sta rt=0xff7 70140,end=0xff77 01bf

[     0.497 906] rockchip_pi nctrl_pr obe:name=drv sta rt=0xff7 701c0,end=0xff77023f

[    0.498525] rockchip_interrupts_register:bank_num=7

[    0.500443] of_get_gpio_init_config:gpio[0] = 2 e = 0

[     0.500463] of _get_gpi o_init_c onfig:gp io[1] =  136, value = 0

[    0.500527] rockchip_ pinctrl_ probe:in it ok

[    0.50 7205] rk_iommu ff900800. iep_mmu:  (iep) Enter

[     0.507 293] rk_iommu ff 900800.iep_mmu:  IOVMM: Created 0 x3ffff00 0 B IOVMM from 0 x1000000 0.

[    0.50730 6] rk_iommu ff900800.iep _mmu: (i ep) Init ialized

[    0. 507477] rk_iommu ff95080 0.vip_mm u: (vip) Enter

[    0.5 07548] r k_iommu ff950800 .vip_mmu : IOVMM: Created  0x3ffff000 B IOVMM from  0x10000 000.

[    0.507 560] rk_ iommu ff 950800.vip_mmu:  (vip) Initialized

[     0.507725 ] rk_iommu ff930 300.vopb _mmu: (vopb) Ent er

[     0.507794] rk_iommu ff93 0300.vop b_mmu: IOVMM: Cr eated 0x 3ffff000 B IOVMM  from 0x 10000000.

[     0.507806] rk_iom mu ff930300.vopb _mmu: (vopb) Initialized

[    0 .507975] rk_iomm u ff940300.vopl_mmu: (vo pl) Ente r

[     0.508047] rk_iom mu ff940 300.vopl_mmu: IO VMM: Cre ated 0x3ffff000 B IOVMM  from 0x10000000.

[    0 .508059]  rk_iommu ff9403 00.vopl_mmu: (vopl) Init ialized

[    0.508228]  rk_iommu ff9c044 0.hevc_mmu: (hev c) Enter

[    0.508301]  rk_iomm u ff9c0440.hevc_mmu: IOV MM: Created 0x3f fff000 B  IOVMM f rom 0x10000000.

[    0.508313] rk_iommu  ff9c044 0.hevc_mmu: (hev c) Initi alized

[    0.508484] r k_iommu  ff9a0800.vpu_mmu : (vpu)  Enter

[    0.50 8555] rk_iommu ff9a0800. vpu_mmu:  IOVMM: Created  0x3ffff0 00 B IOV MM from 0x100000 00.

[     0.508568] rk_iommu ff9 a0800.vpu_mmu: ( vpu) Ini tialized

[    0 .508737] rk_iomm u ff914000.isp_m mu: (isp _mmu) Enter

[     0.5088 12] rk_iommu ff9 14000.is p_mmu: IOVMM: Cr eated 0x 3ffff000 B IOVMM from 0x 10000000 .

[    0.508825 ] rk_iom mu ff914000.isp_ mmu: (is p_mmu) I nitialized

[     0.510718] hw-breakpoint : found  5 (+1 reserved)  breakpoi nt and 4 watchpo int regi sters.

[    0.510731] hw-breakp oint: maximum wa tchpoint  size is 4 bytes .

[     0.511324] rk3368_init_ro ckchip_p mu_ops: could no t find p mu dt node

[     0.51134 7] DDR DEBUG: ve rsion 1.00 20150126

[     0.511 373] DDR  DEBUG: Channel  a:

[     0.511382] DDR DEBUG: D DR3 Device

[     0.51139 5] DDR DEBUG: Bus Width= 32 Col=1 0 Bank=8 Row=15  CS=1 Tot al Capability=10 24MB

[     0.511404] DDR DEBUG:  Channel b:

[     0.5114 11] DDR  DEBUG: DDR3 Devi ce

[    0.511423] DDR D EBUG: Bu s Width=32 Col=1 0 Bank=8  Row=15  CS=1 Total Capab ility=10 24MB

[    0.511 432] DDR DEBUG: addr=0xd ac000

[     0.511442] DD R DEBUG:  stride=9, size=256, hal fcap=400 00000

[    0.51 1450] DD R DEBUG: socAddr [0]=0xda c000, socAddr[1] =0xdac10 0

[     0.511460] DDR DEBUG: chA ddr[0]=0xdac000,  chAddr[ 1]=0xdac000

[     0.511471] DDR DEBUG: d tar[0]=0 x401b500 0, dtar[1]=0x401 b5000

[     0.511560] DD R DEBUG:  init success!!!  freq=20 0MHz

[    0.511 569] DDR DEBUG:  Channel a:

[     0.5115 81] DDR DEBUG: D TONE=0x1, DTERR=0x0, DTI ERR=0x0,  DTPASS=4,0, DGS L=1,0 ex tra cloc k, DGPS=180,270

[    0.511594] DDR DEBU G: DTONE =0x1, DTERR=0x0, DTIERR= 0x0, DTP ASS=4,0, DGSL=1, 0 extra  clock, DGPS=180, 270

[     0.511606] DDR DEBUG: D TONE=0x1, DTERR= 0x0, DTI ERR=0x0,  DTPASS=4,0, DGS L=1,0 ex tra clock, DGPS= 180,270

[    0.511619] DDR DEBU G: DTONE=0x1, DTERR=0x0,  DTIERR= 0x0, DTPASS=4,0,  DGSL=1, 0 extra clock, D GPS=180, 270

[    0.511631] DDR  DEBUG: ZERR=0, Z DONE=0,  ZPD=0x0,  ZPU=0x0, OPD=0x 0, OPU=0 x0

[    0.51164 0] DDR DEBUG: DRV Pull-U p=0x19,  DRV Pull-Dwn=0x1 9

[     0.511649 ] DDR DEBUG: ODT  Pull-Up=0x2, ODT Pull-D wn=0x2

[    0.511656] DDR DEBUG : Channel b:

[     0.51 1668] DD R DEBUG: DTONE=0 x1, DTER R=0x0, DTIERR=0x 0, DTPAS S=4,0, DGSL=1,0  extra cl ock, DGP S=180,270

[     0.511680] DDR DEBUG: DTO NE=0x1,  DTERR=0x0, DTIER R=0x0, D TPASS=4,0, DGSL= 1,0 extr a clock,  DGPS=180,270

[     0.511692] DDR DEBUG:  DTONE=0 x1, DTERR=0x0, D TIERR=0x 0, DTPASS=4,0, D GSL=1,0  extra cl ock, DGPS=180,27 0

[    0.511705] DDR DE BUG: DTO NE=0x1, DTERR=0x 0, DTIER R=0x0, DTPASS=4, 0, DGSL= 1,0 extr a clock, DGPS=180,270

[     0.511716] DD R DEBUG:  ZERR=0, ZDONE=0 , ZPD=0x 0, ZPU=0x0, OPD= 0x0, OPU =0x0

[     0.511725] DDR DEBUG:  DRV Pull-Up=0x19 , DRV Pu ll-Dwn=0x19

[     0.511733] DDR DEBUG: O DT Pull- Up=0x2,  ODT Pull-Dwn=0x2

[    0 .536417] bio: create sla b <bio-0> at 0

[    0.5 36903] R ockchip hdmi dri ver vers ion 2.0

[    0. 536903] .

[    0.538061 ] SCSI s ubsystem initial ized

[     0.538222] usbcore: re gistered  new interface d river us bfs

[    0.5382 68] usbc ore: registered  new inte rface dr iver hub

[    0 .538351] usbcore: regist ered new  device driver u sb

[     0.540996] rockc hip_i2c  ff650000 .i2c: i2c-0: Roc kchip I2 C adapter

[     0.541565] rockchip_i2c f f140000. i2c: i2c-1: Rock chip I2C  adapter

[    0.542024]  rockchip_i2c ff660000.i 2c: i2c- 2: Rockchip I2C  adapter

[    0.542275]  rockchip_i2c ff1 50000.i2c: i2c-3: Rockch ip I2C adapter

[    0.5 42400] media: Li nux medi a interface: v0. 10

[     0.542442] Linux video c apture i nterface: v2.00

[    0.542503] pps_core : LinuxP PS API v er. 1 registered

[    0 .542513] pps_core: Softw are ver. 5.3.6 -  Copyrig ht 2005-2007 Rod olfo Gio metti <g iometti@linux.it >

[    0.542533] PTP cl ock supp ort registered

[    0.542586] i2c-core:  driver  [bq24296 ] using legacy s uspend m ethod

[    0.54 2596] i2c-core: driver [ bq24296]  using legacy re sume met hod

[     0.543282] ion_drm_heap _create: 0@0

[     0.543 405] Rockchip io n module  is successfully  loaded  (v1.1)

[    0.543571] Advanced  Linux Sound Arch itecture  Driver Initiali zed.

[     0.543973] Blu etooth: Core ver  2.16

[    0.54 4027] NE T: Registered pr otocol f amily 31

[    0 .544038]  Bluetoo th: HCI device a nd conne ction manager in itialize d

[    0.544053 ] Blueto oth: HCI socket  layer in itialize d

[    0.544067 ] Blueto oth: L2CAP socke t layer  initialized

[     0.5440 92] Bluetooth: S CO socke t layer  initialized

[     0.5443 22] cfg80211: Ca lling CR DA to update wor ld regul atory domain

[     0.545 059] --- rk_mipi_screen_p robe--

[    0.545071] r k_mipi_s creen_init_dt: 3 05

[     0.545232] rk_m ipi_scre en_init_ dt: lcd->screen_ init = 1 .

[    0.545243 ] rk_mip i_screen_init_dt : mipi_l cd->dsi_ lane = 4.

[     0.545254 ] rk_mipi_screen _init_dt : lcd->screen->h s_tx_clk  = 389000000.

[     0.54 5264] rk _mipi_screen_ini t_dt: lc d->screen.mipi_d si_num =  1.

[    0.5453 26] rk_m ipi_screen_init_ dt: lcd- >screen- >lcd_rst_delay =  100.

[     0.545358] lc d->lcd_r st_gpio=233,dsi- >lcd_rst _atv_val=1

[     0.54536 8] rk_mi pi_screen_init_d t: Can n ot read property : mipi_l cd_en.

[    0.5 45376] r k_mipi_screen_in it_dt: 4 28

[     0.545442]

[     0.545 442]  childnode- >name =r ockchip,on-cmds1 :length= 2

[    0.545456 ] cmd[1] =05 cmd[ 2]=11 dcs_cmd->d cs_cmd.c md_len=2

[    0 .545476]  

[    0.545476 ]  child node->name =rock chip,on- cmds2:le ngth=2

[    0.5 45489] cmd[1]=05 cmd[2]= 29 dcs_c md->dcs_cmd.cmd_ len=2

[     0.54 5507]

[    0.5 45507]  dcs_name:rockchi p,on-cmd s1,dcs_type:1,si de_id:0, cmd_len:2,delay: 150

[     0.5455 07]

[    0.545 524] [1]=05,[2]=11,

[     0.5455 24]  dcs_name:ro ckchip,o n-cmds2,dcs_type :1,side_ id:0,cmd _len:2,delay:10

[    0.545524]

[    0 .545543] [1]=05,[2]=29,- --rk_mip i_screen_probe-- end

[     0.5456 45] act8846_i2c_ probe,li ne=898

[    0.5 46622] act8846_parse_dt, line=746

[    0.547098]  act8846 _i2c_pro be: act8846_pmic _hold=1

[    0.547118] act8846_ i2c_probe: act88 46_pmic_ sleep=1

[    0.547132] act8846_ i2c_probe: act8846_pmic_ cpu_det_gpio=1

[    0.5 47146] act8846_i 2c_probe : act884 6_pmic_usb_hub_r eset_gpi o=1

[    0.549209] act_ dcdc1: 1200 mV

[    0. 552185] vccio: 3300 mV

[    0. 554064] vdd_logic: 700 < --> 1500 mV at 1 125 mV

[    0.557039]  act_dcdc4: 2000 mV

[     0.5582 57] vcci o_sd: 1800 <-->  3300 mV  at 3300 mV

[     0.5605 67] act_ldo2: 10 50 mV

[    0.562880] act_ldo3:  2800 mV  

[    0.565185 ] act_ld o4: 3300 mV

[     0.567481] act_ldo5: 3 300 mV

[    0.569805]  act_ldo6: 1100 m V

[    0.57211 3] vcc_1 8: 1800 mV

[     0.574411] act_ldo8: 18 50 mV

[    0.5 79176] vdd_arm:  712 <-->  1500 mV at 1100  mV

[     0.583878] vdd_gpu: 71 2 <--> 1500 mV a t 900 mV  

[     0.584626] rk808_ i2c_prob e,line=1355

[     0.585962] The device i s not rk 808 -11

[    0. 586047]  rk808: p robe of 0-001b f ailed wi th error -11

[     0.586114] i2c-core: d river [r k818] using lega cy suspe nd metho d

[    0.586123 ] i2c-co re: driver [rk81 8] using  legacy resume m ethod

[     0.587827] Switching  to clock source arch_sys_ counter

[    0.611305]  rga: Module initialized.

[    0 .612000] rga2 ff 920000.r ga: rga  ion client creat e succes s!

[    0.61217 1] rga: Driver loaded su ccesfull y

[    0.612368 ] fb dis p policy  is sdk

[    0. 612410] rk-fb rockchip-f b: rk fb  ion client crea te succe ss!

[    0.612422] rk-f b rockch ip-fb: rockchip  framebuf fer driver probe

[    0 .612684] prmry screen ti ming par se success

[     0.61270 0] rk-screen rk_ screen.8 : can't find pow er_ctr n ode for lcdc0

[    0.61 2709] pr mry screen power  ctrl pa rse failed

[     0.612775] extend screen  timing  parse success

[     0.61 2822] pw r_ctr_name:lcd_e n

[     0.612822] pwr_type:gpio

[    0.612822]  gpio:227

[    0.612822]  atv_val :1

[     0.612822] delay:10

[     0.612822]

[     0.612853] extend scre en power  ctrl pa rse success

[     0.6128 65] rk-screen rk _screen. 8: rockchip scre en probe  success

[    0 .613318]  Use EDP  as prmry screen

[    0 .613474] rk32-edp rk32-e dp: failed to ge t reset

[    0.613487]  rk32-edp rk32-ed p: failed to get  reset

[    0.613629] r k32-edp  rk32-edp: 1829 r k32 edp  driver probe suc cess

[     0.613818] Use mipi_lc d as ext end screen

[     0.61382 9] rk32-dsi

[     0.613950] rk32_mipi_ds i_probe: 1840:dsi ->host.irq =51

[    0.6 13968] mipi dsi  chip is  not found, read  id:fffff fff, but 3133302 a is cor rect

[    0.613981] rk3 2-mipi f f960000.mipi: rk  mipi_ds i probe fail!

[     0.61 3993] rk32-mipi  ff960000 .mipi: r ockchip mipi_dsi  v1.1 2014-06-17

[    0 .614022]  rk32-mipi: prob e of ff9 60000.mi pi failed with e rror -1


[    0.614750] graphics  fb0: rockchip framebuff er registerd:fb0

[    0 .615057] graphics fb1: r ockchip  framebuffer regi sterd:fb 1

[    0.615232 ] graphi cs fb2: rockchip  framebu ffer reg isterd:fb2

[     0.615399] graphics fb3:  rockchi p framebuffer re gisterd: fb3

[    0.6160 11] rk32 88-lcdc lcdc0: lcdc0: dc lk:13260 0000>>fps:51

[     0.61 6221] rk32-edp r k32-edp:  edp pll locked

[    0.639453]  rk_battery_charg er_detec t_cb , battery_c harger_d etect 1

[    0. 674148] rk32-edp rk32-ed p: 955 m ax link  rate:0.0Gps max  number o f lanes:0

[     0.674163] rk32-edp rk32- edp: Rx  Mx Link  Rate is abnormal :0!defau lt link rate:1.6 2Gps

[     0.674176] rk32-edp rk 32-edp: Rx Max L ane coun t is abn ormal :0 !use de fault la nes:4

[    0.68 0111] rk32-edp rk32-edp:  hw lt e rr:1

[    0.680 122] rk3 2-edp rk32-edp: link tra in faile d!

[    0.74128 2] rk32- edp rk32-edp: 12 20 EDID_ ADDR50 rom_addr  0 LENGTH 80

[     5.426318] rk3 2-edp rk 32-edp: EDID Rea d failed !

[    5.426332 ] rk3288-lcdc lcdc0: wak eup from  standby !

[    5.451366 ] alloc_buffer:ion_phy_a ddr=0x55 c00000

[    5.4 63946] f b0:phy:55c00000> >vir:e0991000>>l en:0x1800000

[     5.463 963] rk3288-lcdc  lcdc0: lcdc0 probe ok,  iommu di sabled

[    5.464401] g raphics fb4: rockchip fr amebuffe r registerd:fb4

[    5. 464732] graphics fb5: ro ckchip f ramebuffer registerd:fb5

[    5.464907]  graphics fb6: rockchip  framebuf fer registerd:fb 6

[     5.465073] graphics fb7:  rockchip  framebuffer reg isterd:f b7

[    5.47524 7] rk3288-lcdc lcdc1: lc dc1: dcl k:176800 000>>fps:220

[     5.475262] rk3288-lcd c lcdc1:  wakeup from sta ndby!

[     5.475274] fb 4:phy:55c00000>> vir:e0991000>>le n:0x1800 000

[    5.4753 02] rk3288-lcdc lcdc1: l cdc1 pro be ok, iommu dis abled

[     5.47 6192] rockchip_s et_mux:w arning ignore ba nk num 1 5

[    5.476321 ] rockchip_set_m ux:warning ignor e bank n um 15

[    5.47 6443] rockchip_set_mux:w arning i gnore bank num 1 5

[     5.476561 ] rockchip_set_m ux:warni ng ignore bank n um 15

[     5.476679] rockchip_s et_mux:warning i gnore ba nk num 1 5

[    5.476792 ] rockchip_set_mux:warni ng ignor e bank num 15

[     5.47 7361] rockchip_s et_mux:w arning i gnore bank num 1 5

[     5.477515] rockchip_set_m ux:warning ignor e bank n um 15

[    5.47 8057] rockchip_s et_mux:warning i gnore ba nk num 15

[     5.478212 ] rockchip_set_m ux:warning ignore bank n um 15

[     5.47 8756] rockchip_s et_mux:w arning ignore ba nk num 1 5

[    5.478904 ] rockchip_set_m ux:warning ignor e bank n um 15

[    5.47 9455] rockchip_set_mux:w arning i gnore bank num 1 5

[     5.479604 ] rockchip_set_m ux:warni ng ignore bank n um 15

[    5.481141] NE T: Registered protocol f amily 2

[    5. 481806] TCP established  hash table entri es: 4096  (order: 3, 3276 8 bytes)

[    5.481881]  TCP bind hash t able entries: 40 96 (orde r: 3, 32768 byte s)

[     5.481954] TCP: Hash tab les configured ( establis hed 4096  bind 4096)

[     5.482018] TCP: reno re gistered

[    5.482034]  UDP has h table entries:  256 (or der: 1,  8192 bytes)

[     5.482058] UDP-Lite has h table  entries: 256 (or der: 1,  8192 byt es)

[    5.4822 52] NET: Registered prot ocol fam ily 1

[    5.48 2860] Un packing initramf s...

[    5.621 489] Freeing ini trd memo ry: 2840K (c5bf0 000 - c5 eb6000)

[    5. 622323] hw perfevents: e nabled w ith ARMv 7 Cortex-A12 PMU  driver,  7 counters avai lable

[     5.622888] vcodec_ser vice: probe devi ce ff9a0 000.vpu_ service

[    5. 623104]  vcodec_service: No reset  resource define

[    5 .623293] vcodec_ service:  ff9a000 0.vpu_service: p ower on

[    5.623383] vcodec_s ervice: probe de vice ff9a0000.vpu_servic e

[     5.623398 ] vcodec_service : checki ng hw id 4831

[     5.624442] vcodec_ser vice: ff 9a0000.v pu_service: powe r off...

[    5.624487]  vcodec_service: done

[     5.62 4496] vcodec_ser vice: in it succe ss

[    5.624568] vcode c_service: probe  device  ff9c0000.hevc_se rvice

[     5.624925] vcodec_ser vice: ff 9c0000.hevc_serv ice: pow er on

[    5.624989] vc odec_service: pr obe devi ce ff9c0000.hevc _service

[    5 .625004] vcodec_service:  checking hw id  6867

[     5.625562] vcodec_serv ice: ff9c0000.he vc_servi ce: powe r off...

[    5 .625604]  vcodec_service:  done

[    5.625612] vc odec_ser vice: init succe ss

[     5.625752] rknandbase v1 .0 2014- 03-31

[    5.62 5886] rk nand: probe of f f400000. nandc fa iled with error  -1

[     5.626030] rknand_driver :ret = 0

[     5.627177 ] audit: initial izing ne tlink so cket (disabled)

[    5.627223] type=200 0 audit( 5.360:1): initia lized

[    5.628068] bo unce poo l size:  64 pages

[    5 .632648] fuse init (API  version  7.22)

[    5.63 3025] ms gmni has been se t to 952

[    5 .634801] Block layer SCS I generic (bsg)  driver v ersion 0.4 loade d (major  246)

[    5.63 4816] io schedul er noop register ed

[     5.634826] io sc heduler  deadline registe red

[     5.634922] io scheduler  cfq reg istered (default )

[     5.636613] IEP Driver loa ded succesfully

[    5. 636705]  Module initializ ed.

[     5.637485] dma-pl330 ff b20000.pdma: Loa ded driv er for PL330 DMA C-236420 8

[     5.637501] dma-pl330 ffb2 0000.pdma:         DBUF F-64x8by tes Num_Chans-5 Num_Peri -6 Num_Events-10

[    5.638838] dma-pl330 ff250 000.pdma : Loaded driver for PL33 0 DMAC-2364208

[    5.638855] dma-pl330  ff25000 0.pdma:         DBUFF-128x8byte s Num_Chans-8 Num_Peri-2 0 Num_Ev ents-16

[    5.639133]  pwm-voltage-regulator pwm_regula tor.22: unable t o request PWM, trying le gacy API

[    5.639147] pwm-vol tage-regulator pwm_regul ator.22:  unable to request legac y PWM

[    5.639156] pw m_regulator_probe:error

[    5. 639178] platform pwm_reg ulator.22: Driver pwm-vo ltage-regulator  requests probe deferral

[    5.639386]  rk_serial.c v1.8 2014-03 -04

[    5.6396 10] ff180000.serial: tty S0 at MMIO 0xff180000 (i rq = 87)  is a rk29_serial.0

[     5.639796] serial ff180 000.serial: membase e219 2000

[     5.639945] ff690000.se rial: ttyS2 at MMIO 0xff 690000 ( irq = 89) is a rk29_seri al.2

[    5.640 039] 2, baud is:115200

[    5.641747] c onsole [ttyS2] enabled

[    5.641935] serial ff 690000.serial: m embase fed60000

[    5. 644767] loop: mo dule loaded

[     5.645160] zram: Create d 1 device(s) ...

[     5.645242] i2c-co re: driver [mpu6 050B1] using legacy susp end method

[    5.64525 5] i2c-core: driver [mpu 6050B1]  using legacy resume meth od

[    5.645272] mpu_i nit: Probe name mpu6050B 1

[     5.645427] ak8963_mod_ini t: Probe name ak8963_mod

[    5 .646178] SCSI Media Chan ger driver v0.25

[     5.646436] dws->r egs: e21be000

[     5.647678] ro ckchip_spi_probe:num_cs= 2,bus_num=0,irq=76,freq= 45692308  ok

[    5.647982] tun:  Univers al TUN/TAP devic e driver , 1.6

[     5.64 7996] tu n: (C) 1 999-2004 Max Kra snyansky  <maxk@q ualcomm.com>

[     5.648 119] vmac_init.

[    5.648686]  stmmac_probe_con fig_dt:  Can not read pro perty: pmu_regulator.

[     5.64 8703] stmmac_pro be_confi g_dt: cl ock input/output? (input ).

[    5.64871 6] stmma c_probe_config_d t: TX de lay(0x30).

[     5.648728] stmma c_probe_config_d t: RX de lay(0x20).

[     5.64877 7] stmmac_probe_ config_d t: is rockchip,r k3288-gm ac

[     5.648788] stmmc_pltfr_i nit:

[    5.648 798] stm mc_pltfr_init: E RROR: Ge t power-gpio fai led.

[     5.648 830] gmac_phy_re set: ERR OR: Request pin  stmmc_pl tfr_init failed.

[    5 .648842] stmmc_p ltfr_ini t: init  for RGMII

[     5.648853 ] tx delay=0x30

[    5. 648853] rx delay =0x20

[     5.64 8869] tx delay=0 x30

[     5.648869] rx d elay=0x2 0

[    5.649341 ] stmmac  - user ID: 0x10 , Synops ys ID: 0 x35

[    5.6493 54]  Nor mal descriptors

[    5. 649363]  Ring mo de enabl ed

[    5.64937 4]  DMA  HW capab ility register s upported

[    5.649386]   RX Che cksum Offload En gine sup ported (type 2)

[    5. 649396]   TX Checksum ins ertion s upported

[    5 .649405]   Wake-Up On Lan  support ed

[    5.64944 4]  Enab le RX Mi tigation via HW  Watchdog  Timer

[    5.6 49900] P PP generic drive r versio n 2.4.2

[    5. 650049]  PPP BSD  Compression modu le regis tered

[    5.65 0063] PP P Deflate Compre ssion mo dule reg istered

[    5. 650085]  PPP MPPE Compres sion mod ule registered

[    5.6 50099] NET: Regi stered p rotocol  family 24

[     5.650137 ] SLIP: version  0.8.4-NE T3.019-NEWTTY (d ynamic c hannels, max=256 ) (6 bit  encapsu lation enabled).

[    5 .650151] CSLIP: code cop yright 1989 Rege nts of t he University of  Califor nia.

[     5.650165] Roc kchip Wi Fi SYS interface  (V1.00)  ...

[    5.65 0198] esp_mem_init enter  date Ma r 20 201 7 00:37:10

[     5.65021 0] esp_mem_init VERSION  [V2.5]

[    5.6 50254] e sp_mem_i nit complete

[     5.650340] usbcore: r egistere d new interface  driver c atc

[    5.6503 79] usbc ore: reg istered new inte rface driver kaweth

[     5.6503 92] pegasus: v0. 9.3 (201 3/04/25), Pegasu s/Pegasu s II USB  Ethernet driver

[    5 .650437] usbcore: regist ered new interfa ce drive r pegasus

[     5.650476] usbcor e: registered ne w interf ace driver rtl81 50

[     5.650514] usbco re: regi stered new inter face driver r815 2

[    5.650526 ] hso: d rivers/net/usb/h so.c: Op tion Wireless

[    5.65 0597] usbcore: r egistere d new in terface driver hso

[     5.650641] usbcore: regi stered new inter face dri ver asix

[    5 .650681] usbcore : registered new  interfa ce driver ax8817 9_178a

[    5.650725] u sbcore:  register ed new interface driver  cdc_ether

[     5.650764 ] usbcore: regis tered ne w interface driv er cdc_e em

[     5.650802] usbcore: regi stered new inter face dri ver dm9601

[     5.65083 9] usbcore: regi stered n ew interface driver dm96 20

[     5.650886] usbco re: regi stered new inter face dri ver smsc75xx

[     5.650931] usb core: registered  new int erface driver sm sc95xx

[    5.650976] usbcore:  registered new i nterface  driver  gl620a

[    5.6 51016] u sbcore: register ed new i nterface driver  net1080
回复

使用道具 举报

114

积分

0

威望

0

贡献

技术小白

积分
114
发表于 2022-3-23 14:03:16     
Firefly-RK3288 mipi chip is not found 問題

-->這問題可以將rockchip, uboot-logo-on = <0> 改成 <1>

且在uboot 階段也增加LCM相對應timing 就可以正常點亮7'' MIPI屏
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

友情链接 : 爱板网 电子发烧友论坛 云汉电子社区 粤ICP备14022046号-2
快速回复 返回顶部 返回列表