| Version V2.06 20211109 CHIP ID = 0x0003308C In 589MHz DDR3 Col=10 Bank=3 Row=13 Size=128MB OUT: sdram_init finish. DDR Version V2.06 20211109 CHIP ID = 0x0003308C In 589MHz DDR3 Col=10 Bank=3 Row=13 Size=128MB OUT: sdram_init finish. Boot1 Release Time: Oct 28 2021 16:52:39, version: 1.33 0xff0000a4:a14a ROM VER:0x30303356, 25 chip_id:330800,0 ChipType = 0x19, 646 DPLL = 1300 MHz ...nandc_flash_init enter... No.1 FLASH ID:ff ff ff ff ff ff DPLL = 1300 MHz sfc nor id: ff c8 52 DPLL = 1300 MHz sfc_nand id: c8 52 c8 SFTL version: 5.0.56 20210329 SdmmcInit=0 NOT PRESENT StorageInit ok = 135967 SecureMode = 0 Secure read PBA: 0x4 Secure read PBA: 0x104 Secure read PBA: 0x204 Secure read PBA: 0x304 Secure read PBA: 0x404 SecureInit ret = 0, SecureMode = 0 atags_set_bootdev: ret:(0) GPT part: 0, name: uboot, start:0x2000, size:0x1000 GPT part: 1, name: trust, start:0x3000, size:0x1000 GPT part: 2, name: misc, start:0x4000, size:0x800 GPT part: 3, name: recovery, start:0x4800, size:0xa000 GPT part: 4, name: boot, start:0xe800, size:0xa000 GPT part: 5, name: rootfs, start:0x18800, size:0x40000 GPT part: 6, name: oem, start:0x98800, size:0x20000 GPT part: 7, name: userdata, start:0xb8800, size:0xfffba7df find part:uboot OK. first_lba:0x2000. find part:trust OK. first_lba:0x3000. LoadTrust Addr:0x3000 No find bl30.bin No find bl32.bin Load uboot, ReadLba = 2000 Load OK, addr=0x600000, size=0xa85dc RunBL31 0x40000 @ 286932 us INFO: Preloader serial: 2 NOTICE: BL31: v1.3(release):d5a5a89b7 NOTICE: BL31: Built : 03:20:20, Oct 18 2021 INFO: Lastlog: last=0x100000, realtime=0x102000, size=0x2000 INFO: ARM GICv2 driver initialized INFO: Using opteed sec cpu_context! INFO: boot cpu mask: 1 INFO: plat_rockchip_pmu_init: pd status 0xe bs INFO: BL31: Initializing runtime services WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK ERROR: Error initializing runtime service opteed_fast INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x600000 INFO: SPSR = 0x3c9 U-Boot 2017.09(u-boot commit id: 8e1ac1bfcbb69968910ba413b31cbc317b77b262)(sdk version: rk3308_linux_release_20220304_v1.5.0a.xml)-g8e1ac1bfcb-dirty (Sep 22 2022 - 15:17:52 +0800) Model: Rockchip RK3308 EVB PreSerial: 2 DRAM: 126 MiB Sysmem: init Relocation Offset is: 0790a000 Using default environment __________here board_init __________here boot_devtype_init 101 sfc nor id: ff c8 52 ret -1 _____________here sfc_nand_init _____________here sfc_nand_init sfc_nand id: c8 52 c8 sfc_nand id: c8 52 c8 _____________here get spi_nand_info SFTL version: 5.0.51 20191028 Bootdev(atags): spinand 0 PartType: EFI boot mode: recovery (misc) Found DTB in recovery part DTB: rk-kernel.dtb Error binding driver 'fixed regulator': -22 Some drivers failed to bind vdd_core init 1015000 uV DVFS: cpu: low=0.0'c, high=55.0'c, Vmax=1200000uV, tz_temp=55.0'c, h_repeat=0, l_repeat=0 DVFS: 33.700'c Model: Firefly ROC-RK3308B-CC-PLUS analog mic board __________here setup_boot_mode __________here boot_devtype_init 101 __________here:setup_boot_mode,1 CLK: (uboot. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A) apll 816000 KHz dpll 1300000 KHz vpll0 1177823 KHz vpll1 901583 KHz aclk_bus 185714 KHz hclk_bus 100000 KHz pclk_bus 100000 KHz aclk_peri 185714 KHz hclk_peri 100000 KHz pclk_peri 100000 KHz hclk_audio 98151 KHz pclk_audio 98151 KHz Net: Error: ethernet@ff4e0000 address not set. No ethernet found. DVFS: cpu 33.700'c, 816000000 Hz, 1015000 uV Hit key to stop autoboot('CTRL+C'): 0 ANDROID: reboot reason: "recovery" Fdt Ramdisk skip relocation Booting LZ4 kernel at 0x02480000(Uncompress to 0x00280000) with fdt at 0x1f00000... ## Booting Android Image at 0x0247f800 ... Kernel load addr 0x00280000 size 6588 KiB RAM disk load addr 0x04000000 size 6086 KiB ## Flattened Device Tree blob at 01f00000 Booting using the fdt blob at 0x1f00000 Uncompressing Kernel Image ... OK Using Device Tree in place at 0000000001f00000, end 0000000001f18a41 Adding bank: 0x00200000 - 0x08000000 (size: 0x07e00000) Total: 1365.721 ms Starting kernel ... 日志如上，把DDR和flash按照瑞芯微的支持列表更换了更换了，4G的EMMC改为SPINandFlash，DDR由512MB改为256MB，在uboot最后启动kernel的时候启动失败，请问更换DDR和FLASH后SDK中应该如何更改 |
-
-
2.09 KB, 下载次数: 0, 下载积分: 灯泡 -1 , 经验 -1
