Firefly开源社区

打印 上一主题 下一主题

[技术讨论] 3588核心板 启动失败问题

8

积分

0

威望

0

贡献

吃瓜的群众

积分
8

3588核心板 启动失败问题

发表于 2023-4-17 15:56:59      浏览:5430 | 回复:3        打印      只看该作者   [复制链接] 楼主

我司购买的你们的 3588 核心板   装在我们自己设计的底板上,使用你们提供的sdk无法启动 。







INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-444-g1450d21e8:derrick.huang
NOTICE:  BL31: Built : 16:25:50, Oct 12 2022
INFO:    spec: 0x1
INFO:    ext 32k is not valid
INFO:    ddr: stride-en 4CH
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    valid_cpu_msk=0xff bcore0_rst = 0x0, bcore1_rst = 0x0
INFO:    system boots from cpu-hwid-0
INFO:    idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO:    dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO:    dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO:    dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO:    dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO:    BL31: Initialising Exception Handling Framework
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
INFO:    hdmirx_handler: dma not on, ret
I/TC:
I/TC: OP-TEE version: 3.13.0-652-g4542e1efd #derrick.huang (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #5 2022年 09月 20日 星期二 09:41:09 CST aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


U-Boot 2017.09(u-boot commit id: e8b5ef0c39)(sdk version: rk3588_linux_release_20221117_v1.0.4b)-ge8b5ef0c39 #lvsx (Nov 25 2Model: Rockchip RK3588 Evaluation Board
PreSerial: 2, raw, 0xfeb50000
DRAM:  7.7 GiB
Sysmem: init
Relocation Offset: eda1c000
Relocation fdt: eb9f9fb8 - eb9fecc0
CR: M/C/I
Using default environment

mmc@fe2c0000: 1, mmc@fe2e0000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
DM: v2
boot mode: recovery (misc)
FIT: no signed, no conf required
=================begin===================
165145 bytes read in 7 ms (22.5 MiB/s)
DTB(Distro): rk-kernel.dtb
I2c0 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big0_s0 800000 uV
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big1_s0 800000 uV
I2c1 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_npu_s0 800000 uV
spi2: RK806: 2
ON=0x00, OFF=0x00
vdd_gpu_s0 750000 uV
vdd_cpu_lit_s0 750000 uV
vdd_log_s0 750000 uV
vdd_vdenc_s0 init 750000 uV
vdd_ddr_s0 850000 uV
I2c6 speed: 400000Hz
Error reading output register
Error reading output register
Error reading output register
Error reading output register
Error reading output register
Error reading output register
Error reading output register
Error reading output register
Error reading output register
rockchip_panel_probe: Cannot get enable GPIO: -110
Error reading output register
rockchip_panel_probe: Cannot get enable GPIO: -110
get vp0 plane mask:0x5, primary id:2, cursor_plane:-1, from dts
get vp1 plane mask:0xa, primary id:3, cursor_plane:-1, from dts
get vp2 plane mask:0x140, primary id:8, cursor_plane:-1, from dts
get vp3 plane mask:0x280, primary id:9, cursor_plane:-1, from dts
Could not find baseparameter partition
pre init conn error
Model: Firefly ITX-3588J MIPI101(Android)
Rockchip UBOOT DRM driver version: v1.0.1
vp0 have layer nr:2[0 2 ], primary plane: 2
vp1 have layer nr:2[1 3 ], primary planee: 8
vp3 have layer nr:2[7 9 ], primary plane: 9
hdmi@fde80000 disconnected
edid base block is 0, get edid failed
can't get edid block:0
failed to get edid
Could not find baseparameter partition
color_format:0
hdmi_select_link_config use tmds mode
mode:1920x1080 bus_format:0x100a
hdmi@fdea0000:  detailed mode clock 148500 kHz, flags[5]
    H: 1920 2008 2052 2200
    V: 1080 1084 1089 1125
bus_format: 100a
VOP update mode to: 1920x1080p60, type: HDMI1 for VP1
dclk:148500,if_pixclk_div;2,if_dclk_div:4
hdptx_ropll_cmn_config bus_width:16a8c8 rate:1485000
hdptx phy pll locked!
VP1 set crtc_clock to 1485KHz
VOP VP1 enable Esmart1[500x501->500x501@710x289] fmt[2] addr[0xedf20000]
CEA mode used vic=16
mtmdsclock:148500000
hdptx_ropll_cmn_config bus_width:16a8c8 rate:1485000
hdptx phy pll locked!
dw_hdmi_setup HDMI mode
don't use dsc mode
dw hdmi qp use tmds mode
bus_width:0x16a8c8,bit_rate:1485000
hdptx phy lane locked!
CLK: (uboot. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A)
  b0pll 24000 KHz
  b1pll 00 KHz
  v0pll 24000 KHz
  aupll 786431 KHz
  cpll 1500000 KHz
  gpll 1188000 KHz
  npll 850000 KHz
  ppll 1100000 KHz
  aclk_center_root 702000 KHz
  pclk_center_root 100000 KHz
  hclk_center_root 396000 KHz
  aclk_center_low_root 500000 KHz
  aclk_top_root 594000 KHz
  pclk_top_root 100000 KHz
  aclk_low_top_root 396000 KHz
Net:   eth0: ethernet@fe1b0000, eth1: ethernet@fe1c0000
Hit key to stop autoboot('CTRL+C'):  0
ANDROID: reboot reason: "recovery"
optee api revision: 2.0
TEEC: Waring: Could not find security partition
Not AVB images, AVB skip
No valid android hdr
Android image load failed
Android boot failed, error -1.
## Booting FIT Image at 0xe6cc5980 with size 0x04b33600
Fdt Ramdisk skip relocation
## Loading kernel from FIT Image at e6cc5980 ...
   Using 'conf' configuration
## Verified-boot: 0
   Trying 'kernel' kernel subimage
     Description:  unavailable
     Type:         Kernel Image
     Compression:  uncompressed
     Data Start:   0xe6cee780
     Data Size:    41753088 Bytes = 39.8 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x00400000
     Entry Point:  0x00400000
     Hash algo:    sha256
     Hash value:   32702911fc993c38188c0210e7ac59b843d701d06320456a6c9f493c2b1cedec
   Verifying Hash Integrity ... sha256+ OK
## Loading ramdisk from FIT Image at e6cc5980 ...
   Using 'conf' configuration
   Trying 'ramdisk' ramdisk subimage
     Description:  unavailable
     Type:         RAMDisk Image
     Compression:  uncompressed
     Data Start:   0xe94c0180
     Data Size:    36932945 Bytes = 35.2 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x0a200000
     Entry Point:  unavailable
     Hash algo:    sha256
     Hash value:   993174280a559715c65c49c171ee705cba9c0043aa3dcea430d4bae4a474bb1e
   Verifying Hash Integrity ... sha256+ OK
   Loading ramdisk from 0xe94c0180 to 0x0a200000
## Loading fdt from FIT Image at e6cc5980 ...
   Using 'conf' configuration
   Trying 'fdt' fd
     Description:  unavailable
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0xe6cc6180
     Data Size:    165145 Bytes = 161.3 KiB
     Architecture: AArch64
     Load Address: 0x08300000
     Hash algo:    sha256
     Hash value:   cfcd08da4812577ac619e78b7c0de9edae86c25328d503499df7bf7762d866b0
   Verifying Hash Integrity ... sha256+ OK
   Loading fdt from 0x08300000 to 0x08300000
   Booting using the fdt blob at 0x08300000
   Loading Kernel Image from 0xe6cee780 to 0x00400000 ... OK
   kernel loaded at 0x00400000, end = 0x02bd1a00
  'reserved-memory' cma: addr=10000000 size=10000000
  'reserved-memory' ramoops@110000: addr=110000 size=f0000
   Using Device Tree in place at 0000000008300000, end 000000000832b518
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x100000000 - 0x200000000 (size: 0x100000000)
Total: 4725.58 ms

Starting kernel ...

[    4.852376] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[    4.852399] Linux version 5.10.110 (lvsx@tchip14) (ke 4a55b55733a0) (sdk version: rk3588_linux_release_20221117_v1.0.4b) (aarch64-none-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 10.3.1 20210621, GNU ld -profile Architecture 10.3-2021.07 (arm-10.29)) 2.36.1.20210621) #4 SMP Thu Nov 24 10:42:13 CST 2022
[    4.859541] Machine model: Firefly ITX-3588J MIPI101(Android)
[    4.859619] earlycon: uart8250 at MMIO32 0x00000000feb50000 (options '')
[    4.864397] printk: bootconsole [uart8250] enabled
[    4.866513] efi: UEFI not found.
[    4.870645] OF: fdt: Reserved memory: failed to reserve memory for node 'drm-cubic-lut@00000000': base 0x0000000000000000, size 0 MiB
[    4.871790] Reserved memory: created CMA memory pool at 0x0000000010000000, size 256 MiB
[    4.872528] OF: reserved mem: initialized node cma, compatible id shared-dma-pool
[    4.981049] Zone ranges:
[    4.981292]   DMA      [mem 0x0000000000200000-0x00000000ffffffff]
[    4.981863]   DMA32    em4.982129]   Normal   [mem 0x000000000000-0x00000001ffffffff]
[    4.982695] Movable zone start for each node
[    4.983085] Early memory node ranges
[    4.983413]   node   0: [mem 0x0000000000200000-0x00000000083fffff]
[    4.983986]   node   0: [mem 0x0000000009400000-0x00000000efffffff]
[    4.984560]   node   0: [mem 0x0000000100000000-0x00000001ffffffff]
[    4.985134] Initmem setup node 0 [mem 0x0000000000200000-0x00000001ffffffff]
[    5.029563] psci: probing for conduit method from DT.
[    5.030031] psci: PSCIv1.1 detected in firmware.
[    5.030453] psci: Using standard PSCI v0.2 function IDs
[    5.030933] psci: Trusted OS migration not required
[    5.031381] psci: SMC Calling Convention v1.2
[    5.032148] percpu: Embedded 32 pages/cpu s93160 r8192 d29720 u131072
[    5.032937] Detected VIPT I-cache on CPU0
[    5.033336] CPU features: detected: GIC system register CPU interface
[    5.033925] CPU features: detected: Virtualization Host Extensions
[    5.034494] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[    5.035137] alternatives: patching kernel code
[    5.037531] Built 1 zonelists, mobility grouping on.  Total pages: 1995336
[    5.038165] Kernel command line: storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal  storagenode=/mmc@fe2e0000 androidboot.verifiedbootstate=orange ro rootwait earlycon=uart8250,mmio32,0xfeb50000 console=ttyFIQ0 irqchip.gicv3_pseudo_nmi=0 root=PARTLABEL=rootfs rootfstype=ext4 overlayroot=device:dev=PARTLABEL=userdata,fstype=ext4,mkfs=1 coherent_pool=1m systemd.gpt_auto=0 cgroup_enable=memory swapaccount=1
[    5.042591] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[    5.043689] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    5.044406] mem auto-init: stack:off, heap alloc:off, heap free:off
[    5.050856] software IO TLB: mapped [mem 0x00000000e9f00000-0x00000000edf00000] (64MB)
[    5.110138] Memory: 7544012K/8108032K available (22336K kernel code, 3782K rwdata, 6888K rodata, 7616K init, 656K bss, 301876K reserved, 262144K cma-reserved)
[    5.111542] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    5.112166] ftrace: allocating 67395 entries in 264 pages
[    5.205046] ftrace: allocated 264 pages with 2 groups
[    5.205753] rcu: Hierarchical RCU implementation.
[    5.206188] rcu:     RCU event tracing is enabled.
[    5.206603]  Rude variant of Tasks RCU enabled.
[    5.207018]  Tracing variant of Tasks RCU enabled.
[    5.207456] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[    5.212857] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    5.215194] GICv3: GIC: Using split EOI/Deactivate mode
[    5.215676] GICv3: 480 SPIs implemented
[    5.216027] GICv3: 0 Extended SPIs implemented
[    5.216456] GICv3: Distributor has no Range Selector support
[    5.216978] GICv3: 16 PPIs implemented
[    5.217361] GICv3: CPU0: found redistributor 0 region 0:0x00000000fe680000
[    5.218085] ITS [mem 0xfe640000-0xfe65ffff]
[    5.218508] ITS@0x00000000fe640000: allocated 8192 Devices @100220000 (indirect, esz 8, psz 64K, shr 0)
[    5.219381] ITS@0x00000000fe640000: allocated 32768 Interrupt Collections @100230000 (flat, esz 2, psz 64K, shr 0)
[    5.220328] ITS: using cache flushing for cmd queue
[    5.220800] ITS [mem 0xfe660000-0xfe67ffff]
[    5.221218] ITS@0x00000000fe660000: allocated 8192 Devices @100250000 (indirect, esz 8, psz 64K, shr 0)
[    5.222092] ITS@0x00000000fe660000: allocated 32768 Interrupt Collections @100260000 (flat, esz 2, psz 64K, shr 0)
[    5.223038] ITS: using cache flushing for cmd queue
[    5.223608] GICv3: using LPI property table @0x0000000100270000
[    5.224253] GIC: using cache flushing for LPI property table
[    5.224774] GICv3: CPU0: using allocated LPI pending table @0x0000000100280000
[    5.225574] random: get_random_bytes called from start_kernel+0x3f0/0x65c with crng_init=0
[    5.333866] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    5.335188] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    5.336183] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    5.337777] Console: colour dummy device 80x25
[    5.338211] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[    5.339159] pid_max: default: 32768 minimum: 301
[    5.339664] LSM: Security Framework initializing
[    5.340146] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    5.340856] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    5.343001] rcu: Hierarchical SRCU implementation.
[    5.344175] Platform MSI: msi-controller@fe640000 domain created
[    5.344740] Platform MSI: msi-controller@fe660000 domain created
[    5.345544] PCI/MSI: /interrupt-controller@fe600000/msi-controller@fe640000 domain created
[    5.346318] PCI/MSI: /interrupt-controller@fe600000/msi-controller@fe660000 domain created
[    5.347172] EFI services will not be available.
[    5.347844] smp: Bringing up secondary CPUs ...
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boot
I/TC: Secondary CPU 4 initializing
I/TC: Secondary CPU 4 switching to normal world boot
I/TC: Secondary CPU 5 initializing
I/TC: Secondary CPU 5 switching to normal world boot
I/TC: Secondary CPU 6 initializing
I/TC: Secondary CPU 6 switching to normal world boot
I/TC: Secondary CPU 7 initializing
I/TC: Secondary CPU 7 switching to normal world boot
[    5.349376] Detected VIPT I-cache on CPU1
[    5.349402] GICv3: CPU1: found redistributor 100 region 0:0x00000000fe6a0000
[    5.349416] GICv3: CPU1: using allocated LPI pending table @0x0000000100290000
[    5.349456] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[    5.350618] Detected VIPT I-cache on CPU2
[    5.350639] GICv3: CPU2: found redistributor 200 region 0:0x00000000fe6c0000
[    5.350653] GICv3: CPU2: using allocated LPI pending table @0x00000001002a0000
[    5.350689] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[    5.351822] Detected VIPT I-cache on CPU3
[    5.351841] GICv3: CPU3: found redistributor 300 region 0:0x00000000fe6e0000
[    5.351853] GICv3: CPU3: using allocated LPI pending table @0x00000001002b0000
[    5.351886] CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
[    5.353047] CPU features: detected: Spectre-v4
[    5.353049] CPU features: detected: Spectre-BHB
[    5.353051] Detected PIPT I-cache on CPU4
[    5.353062] GICv3: CPU4: found redistributor 400 region 0:0x00000000fe700000
[    5.353070] GICv3: CPU4: using allocated LPI pending table @0x00000001002c0000
[    5.353092] CPU4: Booted secondary processor 0x0000000400 [0x414fd0b0]
[    5.354186] Detected PIPT I-cache on CPU5
[    5.354197] GICv3: CPU5: found redistributor 500 region 0:0x00000000fe720000
[    5.354205] GICv3: CPU5: using allocated LPI pending table @0x00000001002d0000
[    5.354227] CPU5: Booted secondary processor 0x0000000500 [0x414fd0b0]
[    5.355331] Detected PIPT I-cache on CPU6
[    5.355342] GICv3: CPU6: found redistributor 600 region 0:0x00000000fe740000
[    5.355349] GICv3: CPU6: using allocated LPI pending table @0x00000001002e0000
[    5.355371] CPU6: Booted secondary processor 0x0000000600 [0x414fd0b0]
[    5.356461] Detected PIPT I-cache on CPU7
[    5.356471] GICv3: CPU7: found redistributor 700 region 0:0x00000000fe760000
[    5.356479] GICv3: CPU7: using allocated LPI pending table @0x00000001002f0000
[    5.356501] CPU7: Booted secondary processor 0x0000000700 [0x414fd0b0]
[    5.356553] smp: Brought up 1 node, 8 CPUs
[    5.373684] SMP: Total of 8 processors activated.
[    5.374124] CPU features: detected: Privileged Access Never
[    5.374637] CPU features: detected: User Access Override
[    5.375126] CPU features: detected: 32-bit EL0 Support
[    5.375600] CPU features: detected: Common not Private translations
[    5.376177] CPU features: detected: RAS Extension Support
[    5.376674] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[    5.377471] CPU features: detected: CRC32 instructions
[    5.377944] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[    5.378587] CPU features: detected: RCpc load-acquire (LDAPR)
[    5.379183] CPU: All CPU(s) started at EL2
[    5.381520] devtmpfs: initialized
[    5.389414] Registered cp15_barrier emulation handler
[    5.389882] Registered setend emulation handler
[    5.390363] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    5.391259] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[    5.391994] pinctrl core: initialized pinctrl subsystem
[    5.392667] DMI not present or invalid.
[    5.393111] NET: Registered protocol family 16
[    5.393927] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
[    5.394646] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    5.395372] audit: initializing netlink subsys (disabled)
[    5.395912] audit: type=2000 audit(0.056:1): state=initialized audit_enabled=0 res=1
[    5.396308] thermal_sys: Registered thermal governor 'fair_share'
[    5.396625] thermal_sys: Registered thermal governor 'step_wise'
[    5.397188] thermal_sys: Registered thermal governor 'user_space'
[    5.397739] thermal_sys: Registered thermal governor 'power_allocator'
[    5.398394] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[    5.399744] thermal thermal_zone2: power_allocator: sustainable_power will be estimated
[    5.400495] thermal thermal_zone3: power_allocator: sustainable_power will be estimated
[    5.401250] thermal thermal_zone4: power_allocator: sustainable_power will be estimated
[    5.402003] thermal thermal_zone5: power_allocator: sustainable_power will be estimated
[    5.402756] thermal thermal_zone6: power_allocator: sustainable_power will be estimated
[    5.403500] cpuidle: using governor menu
[    5.403863] Registered FIQ tty driver
[    5.404299] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    5.405010] ASID allocator initialised with 65536 entries
[    5.406422] ramoops: dmesg-0 0x20000@0x0000000000110000
[    5.406910] ramoops: console 0x80000@0x0000000000130000
[    5.407396] ramoops: pmsg    0x50000@0x00000000001b0000
[    5.408069] printk: console [ramoops-1] enabled
[    5.408490] pstore: Registered ramoops as persistent store backend
[    5.409056] ramoops: using 0xf0000@0x110000, ecc: 0
[    5.440862] rockchip-gpio fd8a0000.gpio: probed /pinctrl/gpio@fd8a0000
[    5.441631] rockchip-gpio fec20000.gpio: probed /pnctrl/gpio@fec20000
[    5.442398] rockchip-gpio fec30000.gpio: probed /pinctrl/gpio@fec30000
[    5.443178] rockchip-gpio fec40000.gpio: probed /pinctrl/gpio@fec40000
[    5.443945] rockchip-gpio fec50000.gpio: probed /pinctrl/gpio@fec50000
[    5.444564] rockchip-pinctrl pinctrl: probed pinctrl
[    5.452797] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    5.453412] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[    5.454026] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    5.454640] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[    5.514290] raid6: neonx8   gen()  5934 MB/s
[    5.571011] raid6: neonx8   xor()  4688 MB/s
[    5.627733] raid6: neonx4   gen()  5832 MB/s
[    5.684453] raid6: neonx4   xor()  4985 MB/s
[    5.741176] raid6: neonx2   gen()  5590 MB/s
[    5.797897] raid6: neonx2   xor()  4425 MB/s
[    5.854620] raid6: neonx1   gen()  4621 MB/s
[    5.911339] raid6: neonx1   xor()  3836 MB/s
[    5.968065] raid6: int64x8  gen()  2779 MB/s
[    6.024786] raid6: int64x8  xor()  1646 MB/s
[    6.081508] raid6: int64x4  gen()  3135 MB/s
[    6.138229] raid6: int64x4  xor()  1654 MB/s
[    6.194951] raid6: int64x2  gen()  2655 MB/s
[    6.251669] raid6: int64x2  xor()  1431 MB/s
[    6.308393] raid6: int64x1  gen()  2176 MB/s
[    6.365114] raid6: int64x1  xor()  1143 MB/s
[    6.365506] raid6: using algorithm neonx8 gen() 5934 MB/s
[    6.366003] raid6: .... xor() 4688 MB/s, rmw enabled
[    6.366458] raid6: using neon recovery algorithm
[    6.367297] fiq_debugger fiq_debugger.0: IRQ fiq not found
[    6.367803] fiq_debugger fiq_debugger.0: IRQ wakeup not found
[    6.368332] fiq_debugger_probe: could not install nmi irq handltk: console [ttyFIQ0] enabled
   6.368929] printk: console [ttyFIQ0] enabled
[    6.369713] printk: bootconsole [uart8250] disabled
[    6.369713] printk: bootconsole [uart8250] disabled
[    6.370229] Registered fiq debugger ttyFIQ0
[    6.370505] vcc5v0_sys: supplied by vcc12v_dcin
[    6.370590] vcc5v0_usbdcin: supplied by vcc12v_dcin
[    6.370669] vcc5v0_usb: supplied by vcc12v_dcin
[    6.370748] vcc_1v1_nldo_s3: supplied by vcc5v0_sys
[    6.370881] vcc3v3_pcie30: supplied by vcc12v_dcin
[    6.371097] iommu: Default domain type: Passthrough
[    6.371154] rk_iommu fdab9000.iommu: version = 2
[    6.371423] rk_iommu fdb50800.iommu: version = 2
[    6.371614] rk_iommu fdb60f00.iommu: version = 2
[    6.371751] rk_iommu fdb70f00.iommu: version = 2
[    6.371880] rk_iommu fdb90480.iommu: version = 2
[    6.372025] rk_iommu fdba0800.iommu: version = 2
[    6.372176] rk_iommu fdba4800.iommu: version = 2
[    6.372321] rk_iommu fdba8800.iommu: version = 2
[    6.372468] rk_iommu fdbac800.iommu: version = 2
[    6.372613] rk_iommu fdbb0800.iommu: version = 2
[    6.372755] rk_iommu fdbdf000.iommu: version = 2
[    6.372962] rk_iommu fdbef000.iommu: version = 2
[    6.373192] rk_iommu fdc38700.iommu: version = 2
[    6.373421] rk_iommu fdc48700.iommu: version = 2
[    6.373585] rk_iommu fdce0800.iommu: version = 2
[    6.373670] rk_iommu fdd97e00.iommu: version = 2
[    6.373903] usbcore: registered new interface driver usbfs
[    6.373915] usbcore: registered new interface driver hub
[    6.373927] usbcore: registered new device driver usb
[    6.373953] mc: Linux media interface: v0.10
[    6.373962] videodev: Linux video capture interface: v2.00
[    6.373983] pps_core: LinuxPPS API ver. 1 registered
[    6.373987] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    6.373992] PTP clock support registered
[    6.374187] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
[    6.374215] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0
[    6.375028] Advanced Linux Sound Architecture Driver Initialized.
[    6.375183] Bluetooth: Core ver 2.22
[    6.375194] NET: Registered protocol family 31
[    6.375196] Bluetooth: HCI device and connection manager initialized
[    6.375201] Bluetooth: HCI socket layer initialized
[    6.375205] Bluetooth: L2CAP socket layer initialized
[    6.375211] Bluetooth: SCO socket layer initialized
[    6.376459] rockchip-cpuinfo cpuinfo: SoC            : 35881000
[    6.376464] rockchip-cpuinfo cpuinfo: Serial         : 3a688a2fa1912ae4
[    6.376690] clocksource: Switched to clocksource arch_sys_counter
[    6.623491] NET: Registered protocol family 2
[    6.623584] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    6.625391] tcp_listen_portaddr_hash hash table entries: 4096 (order: 5, 163840 bytes, linear)
[    6.625465] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    6.625782] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear)
[    6.626505] TCP: Hash tables configured (established 65536 bind 65536)
[    6.626549] UDP hash table entries: 4096 (order: 6, 393216 bytes, linear)
[    6.626697] UDP-Lite hash table entries: 4096 (order: 6, 393216 bytes, linear)
[    6.626879] NET: Registered protocol family 1
[    6.627110] RPC: Registered named UNIX socket transport module.
[    6.627114] RPC: Registered udp transport module.
[    6.627117] RPC: Registered tcp transport module.
[    6.627119] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    6.627420] PCI: CLS 0 bytes, default 64
[    6.627640] Trying to unpack rootfs image as initramfs...
[    7.150481] Freeing initrd memory: 36064K
[    7.151023] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    7.151491] kvm [1]: IPA Size Limit: 40 bits
[    7.151502] kvm [1]: GICv3: no GICV resource entry
[    7.151505] kvm [1]: disabling GICv2 emulation
[    7.151508] kvm [1]: GIC system register CPU interface enabled
[    7.151604] kvm [1]: vgic interrupt IRQ9
[    7.151725] kvm [1]: VHE mode initialized successfully
[    7.153789] Initialise system trusted keyrings
[    7.153869] workingset: timestamp_bits=46 max_order=21 bucket_order=0
[    7.155676] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    7.155908] NFS: Registering the id_resolver key type
[    7.155918] Key type id_resolver registered
[    7.155920] Key type id_legacy registered
[    7.155926] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    7.156480] Key type cifs.spnego registered
[    7.156485] Key type cifs.idmap registered
[    7.156490] ntfs: driver 2.1.32 [Flags: R/O].
[    7.156536] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    7.156612] fuse: init (API version 7.32)
[    7.156728] SGI XFS with security attributes, no debug enabled
[    7.176453] NET: Registered protocol family 38
[    7.176460] xor: measuring software checksum speed
[    7.177795]    8regs           :  7425 MB/sec
[    7.178905]    32regs          :  8902 MB/sec
[    7.179737]    arm64_neon      : 11888 MB/sec
[    7.179741] xor: using function: arm64_neon (11888 MB/sec)
[    7.179747] Key type asymmetric registered
[    7.179750] Asymmetric key parser 'x509' registered
[    7.179765] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242)
[    7.179839] io scheduler mq-deadline registered
[    7.179844] io scheduler kyber registered
[    7.180285] rockchip-csi2-dphy-hw fedc0000.csi2-dphy0-hw: csi2 dphy hw probe successfully!
[    7.180512] rockchip-csi2-dphy csi2-dphy0: csi2 dphy0 probe successfully!
[    7.182297] rockchip-usb2phy fd5d8000.syscon:usb2-phy@8000: failed to create phy
[    7.182637] rockchip-usb2phy fd5dc000.syscon:usb2-phy@c000: failed to create phy
[    7.183107] rockchip-usb2phy fd5d4000.syscon:usb2-phy@4000: failed to create phy
[    7.185022] rockchip-hdptx-phy-hdmi fed60000.hdmiphy: hdptx phy init success
[    7.185604] rockchip-hdptx-phy-hdmi fed70000.hdmiphy: hdptx phy init success
[    7.186583] Firefly gpio driver init!
[    7.186663] Firefly gpio driver register return : 0
[    7.187598] rk-pcie fe150000.pcie: invalid prsnt-gpios property in node
[    7.187719] rk-pcie fe170000.pcie: invalid prsnt-gpios property in node
[    7.187730] rk-pcie fe170000.pcie: no vpcie3v3 regulator found
[    7.187848] pwm-backlight backlight: supply power not found, using dummy regulator
[    7.187864] rk-pcie fe170000.pcie: missing legacy IRQ resource
[    7.187873] rk-pcie fe170000.pcie: IRQ msi not found
[    7.187876] rk-pcie fe170000.pcie: use outband MSI support
[    7.187880] rk-pcie fe170000.pcie: Missing *config* reg space
[    7.187886] rk-pcie fe170000.pcie: host bridge /pcie@fe170000 ranges:
[    7.187897] rk-pcie fe170000.pcie:      err 0x00f2000000..0x00f20fffff -> 0x00f2000000
[    7.187929] rk-pcie fe170000.pcie:       IO 0x00f2100000..0x00f21fffff -> 0x00f2100000
[    7.187935] rk-pcie fe170000.pcie:      MEM 0x00f2200000..0x00f2ffffff -> 0x00f2200000
[    7.187939] rk-pcie fe170000.pcie:      MEM 0x0980000000..0x09bfffffff -> 0x0980000000
[    7.187960] rk-pcie fe170000.pcie: Missing *config* reg space
[    7.187981] rk-pcie fe170000.pcie: invalid resource
[    7.188077] iep: Module initialized.
[    7.188103] mpp_service mpp-srv: 75e32fd43421 author: daijh 2022-11-02 Merge branch 'rk3588/rockchip' into rk3588/firefly
[    7.188107] mpp_service mpp-srv: probe start
[    7.189374] mpp_vdpu2 fdb50400.vdpu: Adding to iommu group 1
[    7.189392] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA
[    7.189562] mpp_vdpu2 fdb50400.vdpu: probe device
[    7.189646] mpp_vdpu2 fdb50400.vdpu: reset_group->rw_sem_on=0
[    7.189652] mpp_vdpu2 fdb50400.vdpu: reset_group->rw_sem_on=0
[    7.189748] mpp_vdpu2 fdb50400.vdpu: probing finish
[    7.189912] mpp_vepu2 jpege-ccu: probing start
[    7.189917] mpp_vepu2 jpege-ccu: probing finish
[    7.189995] mpp_vepu2 fdba0000.jpege-core: Adding to iommu group 5
[    7.190006] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA
[    7.190136] mpp_vepu2 fdba0000.jpege-core: probing start
[    7.190219] mpp_vepu2 fdba0000.jpege-core: attach ccu success
[    7.190304] mpp_vepu2 fdba0000.jpege-core: probing finish
[    7.190377] mpp_vepu2 fdba4000.jpege-core: Adding to iommu group 6
[    7.190386] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA
[    7.190503] mpp_vepu2 fdba4000.jpege-core: probing start
[    7.190577] mpp_vepu2 fdba4000.jpege-core: attach ccu success
[    7.190661] mpp_vepu2 fdba4000.jpege-core: probing finish
[    7.190743] mpp_vepu2 fdba8000.jpege-core: Adding to iommu group 7
[    7.190752] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA
[    7.190880] mpp_vepu2 fdba8000.jpege-core: probing start
[    7.190955] mpp_vepu2 fdba8000.jpege-core: attach ccu success
[    7.191048] mpp_vepu2 fdba8000.jpege-core: probing finish
[    7.191120] mpp_vepu2 fdbac000.jpege-core: Adding to iommu group 8
[    7.191129] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA
[    7.191239] mpp_vepu2 fdbac000.jpege-core: probing start
[    7.191310] mpp_vepu2 fdbac000.jpege-core: attach ccu success
[    7.191392] mpp_vepu2 fdbac000.jpege-core: probing finish
[    7.191614] mpp-iep2 fdbb0000.iep: Adding to iommu group 9
[    7.191623] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA
[    7.191734] mpp-iep2 fdbb0000.iep: probe device
[    7.191825] mpp-iep2 fdbb0000.iep: allocate roi buffer failed
[    7.191906] mpp-iep2 fdbb0000.iep: probing finish
[    7.192076] mpp_jpgdec fdb90000.jpegd: Adding to iommu group 4
[    7.192085] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA
[    7.192252] mpp_jpgdec fdb90000.jpegd: probe device
[    7.192414] mpp_jpgdec fdb90000.jpegd: probing finish
[    7.192692] mpp_rkvdec2 fdc30000.rkvdec-ccu: rkvdec-ccu, probing start
[    7.192734] mpp_rkvdec2 fdc30000.rkvdec-ccu: probing finish
[    7.192798] mpp_rkvdec2 fdc38100.rkvdec-core: Adding to iommu group 12
[    7.192807] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA
[    7.394458] rk-pcie fe170000.pci


image.jpg (80.95 KB, 下载次数: 433)

image.jpg

image.jpg (80.95 KB, 下载次数: 399)

image.jpg

image.jpg (80.95 KB, 下载次数: 398)

image.jpg

370.pdf

1.1 MB, 下载次数: 0, 下载积分: 灯泡 -1 , 经验 -1

sch

回复

使用道具 举报

1万

积分

14

威望

13

贡献

管理员

Rank: 9Rank: 9Rank: 9

积分
11194

优秀版主

发表于 2023-4-18 10:01:45        只看该作者  沙发
PCIE3.0 需要 100Mclk 的外置时钟芯片,如果没有系统就会卡死在 pcie 初始化,如果你自己做的底板没有 pcie3.0 接口请关闭 pcie 3.0 接口,另外最好把自己底板没有的接口功能全部都关闭
回复

使用道具 举报

8

积分

0

威望

0

贡献

吃瓜的群众

积分
8
发表于 2023-4-19 13:55:15        只看该作者  板凳
板蓝根 发表于 2023-4-18 10:01
PCIE3.0 需要 100Mclk 的外置时钟芯片,如果没有系统就会卡死在 pcie 初始化,如果你自己做的底板没有 pcie ...

好的,我试试。
回复

使用道具 举报

8

积分

0

威望

0

贡献

吃瓜的群众

积分
8
发表于 2024-3-18 21:42:01        只看该作者  地板
板蓝根 发表于 2023-4-18 10:01
PCIE3.0 需要 100Mclk 的外置时钟芯片,如果没有系统就会卡死在 pcie 初始化,如果你自己做的底板没有 pcie ...

你好,我也遇到了相似的问题,我想请问下怎么关闭不用的接口功能
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

友情链接 : 爱板网 电子发烧友论坛 云汉电子社区 粤ICP备14022046号-2
快速回复 返回顶部 返回列表