|
|
哪位大神帮分析下Android系统无法启动的原因
发表于 2017-9-21 11:41:43
浏览：9177
|
回复：5
打印
只看该作者
[复制链接]
楼主
平台：rk3288
系统：
Android：6.0.1
Linux:3.10.0
下面是系统启动日志
DDR Version 1.00 20160217
In
SRX
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
OUT
U-Boot 2014.10-RK3288-10 (Sep 20 2017 - 12:22:52)
CPU: rk3288
cpu version = 0
CPU's clock information:
arm pll = 600000000HZ
periph pll = 297000000HZ
ddr pll = 200000000HZ
codec pll = 384000000HZ
Board: Rockchip platform Board
DRAM: Found dram banks: 1
Adding bank:0000000000000000(0000000080000000)
128 MiB
GIC CPU mask = 0x00000001
SdmmcInit = 0 400
SdmmcInit = 2 0
storage init OK!
Using default environment
GetParam
Load FDT from boot image.
power key: bank-0 pin-5
pmic:act8846
can't find dts node for pwm1
DCDC vdd_logic has been used, pwm regulator not init it.
Can't find dts node for fuel guage cw201x
SecureBootEn = 0, SecureBootLock = 0
#Boot ver: 2017-09-20#2.30
empty serial no.
checkKey
vbus = 1
no fuel gauge found
no fuel gauge found
read logo on state from dts [1]
pll_src = 0, dclk_hz = 205000000, dclk_div = 2
edp pll locked
Aux Transaction fail!
Aux Transaction fail!
Aux Transaction fail!
Aux Transaction fail!
Aux Transaction fail!
Aux Transaction fail!
Aux Transaction fail!
Aux Transaction fail!
Aux Transaction fail!
Aux Transaction fail!
Aux Transaction fail!
Aux Transaction fail!
Aux Transaction fail!
Aux Transaction fail!
Aux Transaction fail!
Aux Transaction fail!
Aux Transaction fail!
Aux Transaction fail!
Aux Transaction fail!
Aux Transaction fail!
hw lt err:1
link train failed!
unable to config video
no fuel gauge found
got recovery cmd from misc.
Secure Boot state: 0
kernel @ 0x02000000 (0x006e95cc)
ramdisk @ 0x05bf0000 (0x00235914)
bootrk: do_bootm_linux...
Loading Device Tree to 05600000, end 0563c303 ... OK
Add bank:0000000000000000, 0000000080000000
Starting kernel ...
<hit enter to activate fiq debugger>
[ 0.000000] Booting Linux on physical CPU 0x500
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.10.0 (guoys@qzlsv) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #8 SMP PREEMPT Wed Sep 20 19:48:58 CST 2017
[ 0.000000] CPU: ARMv7 Processor [410fc0d1] revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Rockchip RK3288 (Flattened Device Tree), model: rockchip,rk3288
[ 0.000000] rockchip_uboot_logo_setup: mem: 0x02000000@0x7dc00000, offset:0x01000000
[ 0.000000] rockchip_uboot_mem_reserve: reserve 0x02000000@0x7dc00000 for uboot logo
[ 0.000000] rockchip_ion_reserve
[ 0.000000] ion heap(drm): base(0) size(0) align(0)
[ 0.000000] ion heap(cma): base(0) size(28000000) align(0)
[ 0.000000] ion heap(vmalloc): base(0) size(0) align(0)
[ 0.000000] cma: CMA: reserved 640 MiB at 55c00000
[ 0.000000] ion_reserve: cma reserved base 55c00000 size 671088640
[ 0.000000] cma: CMA: reserved 16 MiB at 1e000000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] Boot mode: RECOVERY (2) flag: RECOVER (0xc3524203)
[ 0.000000] PERCPU: Embedded 9 pages/cpu @c1f17000 s13440 r8192 d15232 u36864
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 523296
[ 0.000000] Kernel command line: vmalloc=512M console=ttyS2 androidboot.selinux=permissive androidboot.hardware=rk30board androidboot.console=ttyS2 init=/init mtdparts=rk29xxnand:0x00002000@0x00000000(parameter),0x00002000@0x00002000(uboot),0x00002000@0x00004000(misc),0x00008000@0x00006000(resource),0x00008000@0x0000e000(kernel),0x00010000@0x00016000(boot),0x00010000@0x00026000(recovery),0x0001a000@0x00036000(backup),0x00040000@0x00050000(cache),0x00002000@0x00090000(kpanic),0x00300000@0x00092000(system),0x00008000@0x00392000(metadata),0x00002000@0x0039A000(baseparamer),0x00200000@0x0039C000(userdata),0x00020000@0x0059C000(radical_update),-@0x005BC000(user) storagemedia=emmc uboot_logo=0x02000000@0x7dc00000:0x01000000 loader.timestamp=2017-09-20_12:22:52
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] allocated 4194304 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 2048MB = 2048MB total
[ 0.000000] Memory: 1353624k/1353624k available, 743528k reserved, 901120K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0c23e7c (12400 kB)
[ 0.000000] .init : 0xc0c24000 - 0xc0c7f480 ( 366 kB)
[ 0.000000] .data : 0xc0c80000 - 0xc0d9ba58 (1135 kB)
[ 0.000000] .bss : 0xc0d9ba58 - 0xc0ebf5dc (1167 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] rk_clk_tree_init start!
[ 0.000000] rkclk: _rkclk_add_provider: fail to get ehci1phy_12m_div
[ 0.000000] rkclk: rkclk_cache_parents: ehci1phy_12m_div clk_get error
[ 0.000000] rk_get_uboot_display_flag: uboot_logo_on = 1
[ 0.000000] rkclk_init_clks: cnt_parent = 7
[ 0.000000] rkclk_init_clks: cnt_rate = 28
[ 0.000000] rk3288 set GPLL BW 20 for HDMI!
[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] Switching to timer-based delay loop
[ 0.000000] sched_clock: ARM arch timer >56 bits at 24000kHz, resolution 41ns
[ 0.000000] process version: 3
[ 0.000000] channel:0, lkg:18
[ 0.000000] target-temp:80
[ 0.000000] channel:2, lkg:0
[ 0.000000] channel:0, lkg:18
[ 0.000000] channel:1, lkg:16
[ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
[ 0.347697] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.347712] pid_max: default: 32768 minimum: 301
[ 0.347827] Security Framework initialized
[ 0.347844] SELinux: Initializing.
[ 0.347918] Mount-cache hash table entries: 512
[ 0.348542] Initializing cgroup subsys debug
[ 0.348555] Initializing cgroup subsys memory
[ 0.348581] Initializing cgroup subsys freezer
[ 0.348609] CPU: Testing write buffer coherency: ok
[ 0.348918] /cpus/cpu@0 missing clock-frequency property
[ 0.348931] /cpus/cpu@1 missing clock-frequency property
[ 0.348941] /cpus/cpu@2 missing clock-frequency property
[ 0.348950] /cpus/cpu@3 missing clock-frequency property
[ 0.349000] CPU0: thread -1, cpu 0, socket 5, mpidr 80000500
[ 0.349052] Setting up static identity map for 0xc08be930 - 0xc08be988
[ 0.351364] last_log: 0x1d900000 map to 0xdf804000 and copy to 0xdf886000, size 0x80000 early 0x184f (version 3.1)
[ 0.425887] CPU1: Booted secondary processor
[ 0.425919] CPU1: thread -1, cpu 1, socket 5, mpidr 80000501
[ 0.445558] CPU2: Booted secondary processor
[ 0.445581] CPU2: thread -1, cpu 2, socket 5, mpidr 80000502
[ 0.465264] CPU3: Booted secondary processor
[ 0.465287] CPU3: thread -1, cpu 3, socket 5, mpidr 80000503
[ 0.465387] Brought up 4 CPUs
[ 0.465416] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[ 0.465425] CPU: All CPU(s) started in SVC mode.
[ 0.466147] devtmpfs: initialized
[ 0.470415] VFP support v0.3: implementor 41 architecture 3 part 30 variant d rev 0
[ 0.471498] pinctrl core: initialized pinctrl subsystem
[ 0.471743] regulator-dummy: no parameters
[ 0.495829] NET: Registered protocol family 16
[ 0.497627] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.497962] ion_snapshot: 0x1da90000 map to 0xdf907000 and copy to 0xc0e9808c (version 0.1)
[ 0.498239] Registered FIQ tty driver
[ 0.499553] console [ttyFIQ0] enabled
[ 0.499788] Registered fiq debugger ttyFIQ0
[ 0.500400] rockchip_get_bank_data:name=base start=0xff750000,end=0xff7500ff
[ 0.500424] rockchip_get_bank_data:name=mux_bank0 start=0xff730084,end=0xff73008f
[ 0.500444] rockchip_get_bank_data:name=pull_bank0 start=0xff730064,end=0xff73006f
[ 0.500462] rockchip_get_bank_data:name=drv_bank0 start=0xff730070,end=0xff73007b
[ 0.500552] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio1@ff780000 start=0xff780000,end=0xff7800ff
[ 0.500618] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio2@ff790000 start=0xff790000,end=0xff7900ff
[ 0.500682] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio3@ff7a0000 start=0xff7a0000,end=0xff7a00ff
[ 0.500746] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio4@ff7b0000 start=0xff7b0000,end=0xff7b00ff
[ 0.500811] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio5@ff7c0000 start=0xff7c0000,end=0xff7c00ff
[ 0.500875] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio6@ff7d0000 start=0xff7d0000,end=0xff7d00ff
[ 0.500939] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio7@ff7e0000 start=0xff7e0000,end=0xff7e00ff
[ 0.501003] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio8@ff7f0000 start=0xff7f0000,end=0xff7f00ff
[ 0.501075] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio15@ff7f2000 start=0xff7f2000,end=0xff7f20ff
[ 0.501144] rockchip_pinctrl_probe:name=RK3288-GPIO,type=3
[ 0.501160] rockchip_pinctrl_probe:name=base start=0xff770000,end=0xff77013f
[ 0.501174] rockchip_pinctrl_probe:name=pull start=0xff770140,end=0xff7701bf
[ 0.501188] rockchip_pinctrl_probe:name=drv start=0xff7701c0,end=0xff77023f
[ 0.501808] rockchip_interrupts_register:bank_num=7
[ 0.503724] of_get_gpio_init_config:gpio[0] = 6, value = 0
[ 0.503781] rockchip_pinctrl_probe:init ok
[ 0.509829] rk_iommu ff900800.iep_mmu: (iep) Enter
[ 0.509916] rk_iommu ff900800.iep_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.509933] rk_iommu ff900800.iep_mmu: (iep) Initialized
[ 0.510104] rk_iommu ff950800.vip_mmu: (vip) Enter
[ 0.510180] rk_iommu ff950800.vip_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.510196] rk_iommu ff950800.vip_mmu: (vip) Initialized
[ 0.510368] rk_iommu ff930300.vopb_mmu: (vopb) Enter
[ 0.510440] rk_iommu ff930300.vopb_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.510456] rk_iommu ff930300.vopb_mmu: (vopb) Initialized
[ 0.510623] rk_iommu ff940300.vopl_mmu: (vopl) Enter
[ 0.510701] rk_iommu ff940300.vopl_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.510717] rk_iommu ff940300.vopl_mmu: (vopl) Initialized
[ 0.510897] rk_iommu ff9c0440.hevc_mmu: (hevc) Enter
[ 0.510973] rk_iommu ff9c0440.hevc_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.510989] rk_iommu ff9c0440.hevc_mmu: (hevc) Initialized
[ 0.511157] rk_iommu ff9a0800.vpu_mmu: (vpu) Enter
[ 0.511231] rk_iommu ff9a0800.vpu_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.511247] rk_iommu ff9a0800.vpu_mmu: (vpu) Initialized
[ 0.511428] rk_iommu ff914000.isp_mmu: (isp_mmu) Enter
[ 0.511504] rk_iommu ff914000.isp_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 0.511520] rk_iommu ff914000.isp_mmu: (isp_mmu) Initialized
[ 0.513158] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.513174] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.513763] rk3368_init_rockchip_pmu_ops: could not find pmu dt node
[ 0.513788] DDR DEBUG: version 1.00 20150126
[ 0.513818] DDR DEBUG: Channel a:
[ 0.513827] DDR DEBUG: DDR3 Device
[ 0.513842] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Total Capability=1024MB
[ 0.513854] DDR DEBUG: Channel b:
[ 0.513863] DDR DEBUG: DDR3 Device
[ 0.513876] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Total Capability=1024MB
[ 0.513888] DDR DEBUG: addr=0xda5000
[ 0.513899] DDR DEBUG: stride=9, size=256, halfcap=40000000
[ 0.513910] DDR DEBUG: socAddr[0]=0xda5000, socAddr[1]=0xda5100
[ 0.513922] DDR DEBUG: chAddr[0]=0xda5000, chAddr[1]=0xda5000
[ 0.513936] DDR DEBUG: dtar[0]=0x501b4000, dtar[1]=0x501b4000
[ 0.513993] DDR DEBUG: init success!!! freq=200MHz
[ 0.514003] DDR DEBUG: Channel a:
[ 0.514017] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,0 extra clock, DGPS=180,270
[ 0.514032] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,0 extra clock, DGPS=180,270
[ 0.514048] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,0 extra clock, DGPS=180,270
[ 0.514063] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,0 extra clock, DGPS=180,270
[ 0.514078] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0
[ 0.514090] DDR DEBUG: DRV Pull-Up=0x19, DRV Pull-Dwn=0x19
[ 0.514100] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2
[ 0.514110] DDR DEBUG: Channel b:
[ 0.514122] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,0 extra clock, DGPS=180,270
[ 0.514137] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,0 extra clock, DGPS=180,270
[ 0.514153] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,0 extra clock, DGPS=180,270
[ 0.514168] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,0 extra clock, DGPS=180,270
[ 0.514182] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0
[ 0.514193] DDR DEBUG: DRV Pull-Up=0x19, DRV Pull-Dwn=0x19
[ 0.514237] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2
[ 0.540535] bio: create slab <bio-0> at 0
[ 0.541084] Rockchip hdmi driver version 2.0
.
[ 0.541484] SCSI subsystem initialized
[ 0.541642] usbcore: registered new interface driver usbfs
[ 0.541690] usbcore: registered new interface driver hub
[ 0.541782] usbcore: registered new device driver usb
[ 0.544387] rockchip_i2c ff650000.i2c: i2c-0: Rockchip I2C adapter
[ 0.545058] rockchip_i2c ff140000.i2c: i2c-1: Rockchip I2C adapter
[ 0.545512] rockchip_i2c ff660000.i2c: i2c-2: Rockchip I2C adapter
[ 0.545768] rockchip_i2c ff150000.i2c: i2c-3: Rockchip I2C adapter
[ 0.545879] media: Linux media interface: v0.10
[ 0.545926] Linux video capture interface: v2.00
[ 0.546039] pps_core: LinuxPPS API ver. 1 registered
[ 0.546051] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.546075] PTP clock support registered
[ 0.546555] ion_drm_heap_create: 0@0
[ 0.546690] Rockchip ion module is successfully loaded (v1.1)
[ 0.546854] Advanced Linux Sound Architecture Driver Initialized.
[ 0.547251] Bluetooth: Core ver 2.16
[ 0.547290] NET: Registered protocol family 31
[ 0.547303] Bluetooth: HCI device and connection manager initialized
[ 0.547321] Bluetooth: HCI socket layer initialized
[ 0.547336] Bluetooth: L2CAP socket layer initialized
[ 0.547364] Bluetooth: SCO socket layer initialized
[ 0.547619] cfg80211: Calling CRDA to update world regulatory domain
[ 0.548230] act8846_i2c_probe,line=880
[ 0.549251] act8846_parse_dt,line=744
[ 0.549688] act8846_i2c_probe: act8846_pmic_hold=1
[ 0.549713] act8846_i2c_probe: act8846_pmic_sleep=1
[ 0.551789] act_dcdc1: 1200 mV
[ 0.554779] vccio: 3300 mV
[ 0.556660] vdd_logic: 700 <--> 1500 mV at 1100 mV
[ 0.559620] act_dcdc4: 2000 mV
[ 0.560882] vccio_sd: 1800 <--> 3300 mV at 3300 mV
[ 0.563199] act_ldo2: 1000 mV
[ 0.565554] act_ldo3: 3300 mV
[ 0.567874] act_ldo4: 3300 mV
[ 0.570200] act_ldo5: 3300 mV
[ 0.572517] act_ldo6: 1000 mV
[ 0.574878] vcc_18: 1800 mV
[ 0.577199] act_ldo8: 1800 mV
[ 0.582004] vdd_arm: 712 <--> 1500 mV at 1000 mV
[ 0.586746] vdd_gpu: 712 <--> 1500 mV at 1000 mV
[ 0.588441] Switching to clocksource arch_sys_counter
[ 0.613110] rga: Module initialized.
[ 0.613827] rga2 ff920000.rga: rga ion client create success!
[ 0.614051] rga: Driver loaded succesfully
[ 0.614238] uboot-logo-on:1
[ 0.614271] rk-fb rockchip-fb: rk fb ion client create success!
[ 0.614286] rk-fb rockchip-fb: rockchip framebuffer driver probe
[ 0.614591] rk-screen rk_screen.9: rockchip screen probe success
[ 0.614745] rk32-lvds ff96c000.lvds: screen is not lvds/rgb!
[ 0.614768] rk32-lvds: probe of ff96c000.lvds failed with error -22
[ 0.615256] rk32-edp rk32-edp: failed to get reset
[ 0.615272] rk32-edp rk32-edp: failed to get reset
[ 0.615371] rk32-edp rk32-edp: rk32 edp driver probe success
[ 0.616105] graphics fb0: rockchip framebuffer registerd:fb0
[ 0.616427] graphics fb1: rockchip framebuffer registerd:fb1
[ 0.616593] graphics fb2: rockchip framebuffer registerd:fb2
[ 0.616764] graphics fb3: rockchip framebuffer registerd:fb3
[ 0.616992] rk3288-lcdc lcdc0: lcdc0: dclk:205000000>>fps:61
[ 0.640037] rk_battery_charger_detect_cb , battery_charger_detect 1
[ 0.641668] rk3288-lcdc lcdc0: wakeup from standby!
[ 0.692654] alloc_buffer:ion_phy_addr=0x55c00000
[ 0.712163] fb0:phy:55c00000>>vir:df991000>>len:0x2500000
[ 0.718316] rk3288-lcdc lcdc0: lcdc0 probe ok, iommu disabled
[ 0.718521] rk3288-lcdc lcdc1: can't find power_ctr node for lcdc1
[ 0.718537] rk_fb_trsm_ops_get: unsupported transmitter: 0!
[ 0.718799] graphics fb4: rockchip framebuffer registerd:fb4
[ 0.719139] graphics fb5: rockchip framebuffer registerd:fb5
[ 0.719316] graphics fb6: rockchip framebuffer registerd:fb6
[ 0.719478] graphics fb7: rockchip framebuffer registerd:fb7
[ 0.719748] unknow screen type: 0
[ 0.719814] rk3288-lcdc lcdc1: lcdc1: dclk:205000000>>fps:1991
[ 0.744437] rk3288-lcdc lcdc1: wakeup from standby!
[ 0.744453] fb4:phy:55c00000>>vir:df991000>>len:0x2500000
[ 0.744467] rk3288-lcdc lcdc1: lcdc1 probe ok, iommu disabled
[ 0.745227] rockchip_set_mux:warning ignore bank num 15
[ 0.745364] rockchip_set_mux:warning ignore bank num 15
[ 0.745487] rockchip_set_mux:warning ignore bank num 15
[ 0.745604] rockchip_set_mux:warning ignore bank num 15
[ 0.745724] rockchip_set_mux:warning ignore bank num 15
[ 0.745835] rockchip_set_mux:warning ignore bank num 15
[ 0.746430] rockchip_set_mux:warning ignore bank num 15
[ 0.746594] rockchip_set_mux:warning ignore bank num 15
[ 0.747170] rockchip_set_mux:warning ignore bank num 15
[ 0.747316] rockchip_set_mux:warning ignore bank num 15
[ 0.747889] rockchip_set_mux:warning ignore bank num 15
[ 0.748054] rockchip_set_mux:warning ignore bank num 15
[ 0.748605] rockchip_set_mux:warning ignore bank num 15
[ 0.748770] rockchip_set_mux:warning ignore bank num 15
[ 0.750205] NET: Registered protocol family 2
[ 0.750897] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.750981] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.751057] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.751119] TCP: reno registered
[ 0.751136] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.751161] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.751352] NET: Registered protocol family 1
[ 0.751641] RPC: Registered named UNIX socket transport module.
[ 0.751656] RPC: Registered udp transport module.
[ 0.751667] RPC: Registered tcp transport module.
[ 0.751678] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.751900] Unpacking initramfs...
[ 0.862575] Freeing initrd memory: 2260K (c5bf0000 - c5e25000)
[ 0.863305] hw perfevents: enabled with ARMv7 Cortex-A12 PMU driver, 7 counters available
[ 0.865275] vcodec_service: No core reset resource define
[ 0.865497] vcodec_service: probe device ff9a0000.vpu_service
[ 0.865535] vcodec_service: checking hw id 4831
[ 0.865934] vcodec_service: init success
[ 0.866323] vcodec_service: probe device ff9c0000.hevc_service
[ 0.866356] vcodec_service: checking hw id 6867
[ 0.866610] vcodec_service: init success
[ 0.866761] rknandbase v1.0 2014-03-31
[ 0.866889] rknand: probe of ff400000.nandc0 failed with error -1
[ 0.866995] rknand_driver:ret = 0
[ 0.868163] audit: initializing netlink socket (disabled)
[ 0.868229] type=2000 audit(0.520:1): initialized
[ 0.869055] bounce pool size: 64 pages
[ 0.873692] NFS: Registering the id_resolver key type
[ 0.873759] Key type id_resolver registered
[ 0.873771] Key type id_legacy registered
[ 0.874154] fuse init (API version 7.22)
[ 0.874528] msgmni has been set to 920
[ 0.874916]
[ 0.874916] TEE Core Framework initialization (ver 1:0.1)
[ 0.874949] TEE armv7 Driver initialization
[ 0.875275] tz_tee_probe: name="armv7sec", id=0, pdev_name="armv7sec.0"
[ 0.875294] TEE core: Alloc the misc device "opteearmtz00" (id=0)
[ 0.875466] TEE Core: Register the misc device "opteearmtz00" (id=0,minor=60)
[ 0.877125] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 0.877143] io scheduler noop registered
[ 0.877154] io scheduler deadline registered
[ 0.877242] io scheduler cfq registered (default)
[ 0.878447] hdmi phy_table not exist
[ 0.878867] reset hdmi
[ 0.879001] rockchip-hdmiv2 ff980000.hdmi: rockchip hdmiv2 probe sucess.
[ 0.879695] iep ion client create success!
[ 0.879710] IEP Driver loaded succesfully
[ 0.879793] Module initialized.
[ 0.880775] dma-pl330 ffb20000.pdma: Loaded driver for PL330 DMAC-2364208
[ 0.880796] dma-pl330 ffb20000.pdma: DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10
[ 0.882142] dma-pl330 ff250000.pdma: Loaded driver for PL330 DMAC-2364208
[ 0.882163] dma-pl330 ff250000.pdma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[ 0.882486] rk_serial.c v1.8 2014-03-04
[ 0.882715] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 87) is a rk29_serial.0
[ 0.882917] serial ff180000.serial: membase df97e000
[ 0.883158] arm_release_ver of this mali_ko is 'r6p0-02rel0', rk_ko_ver is '13', built at '14:16:43', on 'Sep 20 2017'.
[ 0.883225] mali ffa30000.gpu: Continuing without Mali clock control
[ 0.883263] mali pd enabled
[ 0.883278] clk enabled
[ 0.883291] DVFS ERR: dvfs_target: clk_gpu is disable, set rate error
[ 0.883305] MALI_DVFS_STEP = 5, div_dvfs = 7
[ 0.883318] mali_dvfs_infotbl[0].clock=100000,min_threshold=0,max_threshold=70
[ 0.883332] mali_dvfs_infotbl[1].clock=200000,min_threshold=65,max_threshold=77
[ 0.883346] mali_dvfs_infotbl[2].clock=300000,min_threshold=75,max_threshold=84
[ 0.883359] mali_dvfs_infotbl[3].clock=420000,min_threshold=82,max_threshold=91
[ 0.883372] mali_dvfs_infotbl[4].clock=500000,min_threshold=93,max_threshold=100
[ 0.883480] turn on mali power
[ 0.883494] kbase_platform_rk_init,register_reboot_notifier
[ 0.883561] DVFS ERR: dvfs_target: clk_gpu is disable, set rate error
[ 0.883569] hrtimer: interrupt took 27125 ns
[ 0.883729] mali ffa30000.gpu: GPU identified as 0x0750 r0p0 status 1
[ 0.884453] DVFS ERR: dvfs_target: clk_gpu is disable, set rate error
[ 0.884762] mali ffa30000.gpu: Probed as mali0
[ 0.884867] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 389; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '-c5a435b', rk_ko_ver is '5', built at '14:16:30', on 'Sep 20 2017'.
[ 0.885110] Mali: Mali device driver loaded
[ 0.887761] loop: module loaded
[ 0.888122] zram: Created 1 device(s) ...
[ 0.888289] i2c i2c-1: mpu_probe: 0
[ 0.888401] 6mldl_cfg:Reset MPU6050 B1
[ 0.889381] drivers/misc/inv_mpu/mlsl-kernel.c|inv_i2c_write|48 returning -11
[ 0.889398] drivers/misc/inv_mpu/mldl_cfg.c|mpu60xx_pwr_mgmt|563 returning -11
[ 0.889413] drivers/misc/inv_mpu/mldl_cfg.c|inv_mpu_open|1461 returning -11
[ 0.889429] i2c i2c-1: Unable to open mpu6050B1 -11
[ 0.889444] i2c i2c-1: mpu_probe failed -19
[ 0.889503] i2c-core: driver [mpu6050B1] using legacy suspend method
[ 0.889516] i2c-core: driver [mpu6050B1] using legacy resume method
[ 0.889533] mpu_init: Probe name mpu6050B1
[ 0.889715] bus=0,adapt_num=0,addr=d
[ 0.889727] 1 0 0 0 1 0 0 0 -1
[ 0.889756] i2c i2c-1: ak8963_mod_probe: (null)
[ 0.889767] yemk:ak8963_mod_probe
[ 0.889781] i2c i2c-1: inv_mpu_register_slave: Null mpu_private_data
[ 0.889793] invensense: in ak8963_mod_probe, result is -22
[ 0.889807] i2c i2c-1: Slave registration failed: (null), -22
[ 0.889821] i2c i2c-1: ak8963_mod_probe failed -22
[ 0.889837] ak8963_mod: probe of 1-000d failed with error -22
[ 0.889869] ak8963_mod_init: Probe name ak8963_mod
[ 0.890533] SCSI Media Changer driver v0.25
[ 0.890854] tun: Universal TUN/TAP device driver, 1.6
[ 0.890868] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.891006] vmac_init.
[ 0.891325] PPP generic driver version 2.4.2
[ 0.891490] PPP BSD Compression module registered
[ 0.891503] PPP Deflate Compression module registered
[ 0.891533] PPP MPPE Compression module registered
[ 0.891547] NET: Registered protocol family 24
[ 0.891586] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[ 0.891599] CSLIP: code copyright 1989 Regents of the University of California.
[ 0.891619] Rockchip WiFi SYS interface (V1.00) ...
[ 0.891657] esp_mem_init enter date Sep 20 2017 14:16:52
[ 0.891668] esp_mem_init VERSION [V2.5]
[ 0.891713] esp_mem_init complete
[ 0.891800] usbcore: registered new interface driver catc
[ 0.891840] usbcore: registered new interface driver kaweth
[ 0.891853] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[ 0.891893] usbcore: registered new interface driver pegasus
[ 0.891945] usbcore: registered new interface driver rtl8150
[ 0.892000] usbcore: registered new interface driver r8152
[ 0.892012] hso: drivers/net/usb/hso.c: Option Wireless
[ 0.892085] usbcore: registered new interface driver hso
[ 0.892131] usbcore: registered new interface driver asix
[ 0.892171] usbcore: registered new interface driver ax88179_178a
[ 0.892210] usbcore: registered new interface driver cdc_ether
[ 0.892257] usbcore: registered new interface driver cdc_eem
[ 0.892297] usbcore: registered new interface driver dm9601
[ 0.892335] usbcore: registered new interface driver dm9620
[ 0.892383] usbcore: registered new interface driver smsc75xx
[ 0.892432] usbcore: registered new interface driver smsc95xx
[ 0.892487] usbcore: registered new interface driver gl620a
[ 0.892536] usbcore: registered new interface driver net1080
[ 0.892576] usbcore: registered new interface driver plusb
[ 0.892616] usbcore: registered new interface driver rndis_host
[ 0.892655] usbcore: registered new interface driver cdc_subset
[ 0.892693] usbcore: registered new interface driver zaurus
[ 0.892733] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[ 0.892795] usbcore: registered new interface driver int51x1
[ 0.892835] usbcore: registered new interface driver kalmia
[ 0.892883] usbcore: registered new interface driver ipheth
[ 0.892926] usbcore: registered new interface driver sierra_net
[ 0.892972] usbcore: registered new interface driver cx82310_eth
[ 0.893022] usbcore: registered new interface driver cdc_ncm
[ 0.893062] usbcore: registered new interface driver qmi_wwan
[ 0.893102] usbcore: registered new interface driver cdc_mbim
[ 0.893114] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.893127] ehci-platform: EHCI generic platform driver
[ 0.895771] EHCI: ehci_rk_probe e2f40000 e2f40010
[ 0.895790] rockchip_ehci_host ff500000.usb: EHCI Host Controller
[ 0.895821] rockchip_ehci_host ff500000.usb: new USB bus registered, assigned bus number 1
[ 0.896191] rockchip_ehci_host ff500000.usb: irq 56, io mem 0xff500000
[ 0.904125] DVFS ERR: dvfs_target: clk_gpu is disable, set rate error
[ 0.913238] rockchip_ehci_host ff500000.usb: USB 2.0 started, EHCI 1.00
[ 0.913325] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.913342] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.913358] usb usb1: Product: EHCI Host Controller
[ 0.913370] usb usb1: Manufacturer: Linux 3.10.0 ehci_hcd
[ 0.913384] usb usb1: SerialNumber: ff500000.usb
[ 0.913869] hub 1-0:1.0: USB hub found
[ 0.913902] hub 1-0:1.0: 1 port detected
[ 0.914060] EHCI: ehci_rk_probe ok
[ 0.914152] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.914296] ohci-platform: OHCI generic platform driver
[ 0.914467] usbcore: registered new interface driver cdc_acm
[ 0.914479] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 0.914531] usbcore: registered new interface driver usblp
[ 0.914571] usbcore: registered new interface driver cdc_wdm
[ 0.914634] usbcore: registered new interface driver usb-storage
[ 0.914679] usbcore: registered new interface driver ums-alauda
[ 0.914718] usbcore: registered new interface driver ums-cypress
[ 0.914755] usbcore: registered new interface driver ums-datafab
[ 0.914791] usbcore: registered new interface driver ums_eneub6250
[ 0.914827] usbcore: registered new interface driver ums-freecom
[ 0.914863] usbcore: registered new interface driver ums-isd200
[ 0.914900] usbcore: registered new interface driver ums-jumpshot
[ 0.914936] usbcore: registered new interface driver ums-karma
[ 0.914972] usbcore: registered new interface driver ums-onetouch
[ 0.915011] usbcore: registered new interface driver ums-sddr09
[ 0.915048] usbcore: registered new interface driver ums-sddr55
[ 0.915091] usbcore: registered new interface driver ums-usbat
[ 0.915178] usbcore: registered new interface driver usbserial
[ 0.915220] usbcore: registered new interface driver usbserial_generic
[ 0.915252] usbserial: USB Serial support registered for generic
[ 0.915291] usbcore: registered new interface driver option
[ 0.915321] usbserial: USB Serial support registered for GSM modem (1-port)
[ 0.915414] usbcore: registered new interface driver trancevibrator
[ 0.915427] usb20_otg: version 3.10a 21-DEC-2012
[ 0.915853] e2f80040
[ 0.915867] Core Release: 3.10a
[ 0.915878] Setting default values for core params
[ 0.916003] Using Buffer DMA mode
[ 0.916015] Periodic Transfer Interrupt Enhancement - disabled
[ 0.916027] Multiprocessor Interrupt Enhancement - disabled
[ 0.916039] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 0.916049] ^^^^^^^^^^^^^^^^^Device Mode
[ 0.916064] Dedicated Tx FIFOs mode
[ 0.916083] pcd_init otg_dev = dcf4e080
[ 0.916244] usb20_otg ff580000.usb: DWC OTG Controller
[ 0.916273] usb20_otg ff580000.usb: new USB bus registered, assigned bus number 2
[ 0.916305] usb20_otg ff580000.usb: irq 55, io mem 0x00000000
[ 0.916364] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.916380] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.916394] usb usb2: Product: DWC OTG Controller
[ 0.916407] usb usb2: Manufacturer: Linux 3.10.0 dwc_otg_hcd
[ 0.916420] usb usb2: SerialNumber: ff580000.usb
[ 0.916826] hub 2-0:1.0: USB hub found
[ 0.916850] hub 2-0:1.0: 1 port detected
[ 0.917151] usb20_host: version 3.10a 21-DEC-2012
[ 0.919643] e3000040
[ 0.919657] Core Release: 3.10a
[ 0.919667] Setting default values for core params
[ 0.919790] Using Buffer DMA mode
[ 0.919802] Periodic Transfer Interrupt Enhancement - disabled
[ 0.919812] Multiprocessor Interrupt Enhancement - disabled
[ 0.919824] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 0.919833] ^^^^^^^^^^^^^^^^^^Host Mode
[ 0.919862] usb20_host ff540000.usb: DWC OTG Controller
[ 0.919888] usb20_host ff540000.usb: new USB bus registered, assigned bus number 3
[ 0.919920] usb20_host ff540000.usb: irq 57, io mem 0x00000000
[ 0.920012] Init: Power Port (0)
[ 0.920069] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.920086] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.920101] usb usb3: Product: DWC OTG Controller
[ 0.920119] usb usb3: Manufacturer: Linux 3.10.0 dwc_otg_hcd
[ 0.920145] usb usb3: SerialNumber: ff540000.usb
[ 0.920542] hub 3-0:1.0: USB hub found
[ 0.920564] hub 3-0:1.0: 1 port detected
[ 0.921257] usbcore: registered new interface driver xpad
[ 0.921315] usbcore: registered new interface driver usb_acecad
[ 0.921361] usbcore: registered new interface driver aiptek
[ 0.921405] usbcore: registered new interface driver gtco
[ 0.921456] usbcore: registered new interface driver hanwang
[ 0.921501] usbcore: registered new interface driver kbtab
[ 0.921553] usbcore: registered new interface driver wacom
[ 0.921940] sensor_register_slave:mma8452,id=17
[ 0.921955] sensor_register_slave:mma7660,id=18
[ 0.921967] sensor_register_slave:gs_mc3230,id=23
[ 0.921977] gsensor_init
[ 0.921987] sensor_register_slave:mpu6880_acc,id=24
[ 0.921999] sensor_register_slave:mpu6500_acc,id=25
[ 0.922010] sensor_register_slave:cm3217,id=48
[ 0.922021] sensor_register_slave:cm3218,id=49
[ 0.923822] DVFS ERR: dvfs_target: clk_gpu is disable, set rate error
[ 0.926932] rtc_hym8563 0-0051: rtc core: registered hym8563 as rtc0
[ 0.926979] i2c /dev entries driver
[ 0.927596] IR NEC protocol handler initialized
[ 0.927610] IR RC5(x) protocol handler initialized
[ 0.927620] IR RC6 protocol handler initialized
[ 0.927631] IR JVC protocol handler initialized
[ 0.927640] IR Sony protocol handler initialized
[ 0.927650] IR RC5 (streamzap) protocol handler initialized
[ 0.927660] IR SANYO protocol handler initialized
[ 0.927671] IR MCE Keyboard/mouse protocol handler initialized
[ 0.927824] usbcore: registered new interface driver uvcvideo
[ 0.927836] USB Video Class driver (1.1.1)
[ 0.927848] CamSys driver version: v0.33.0, CamSys head file version: v0.11.0
[ 0.928847] D1:camsys_mipiphy_probe_cb(115): compatible is rockchip,rk3288
[ 0.928847]
[ 0.928926] D1:camsys_mipiphy_probe_cb(186): ff910000.isp mipi phy0 probe success(reg_phy: 0x0 reg_vir: 0x0 size: 0x0)
[ 0.929097] D1:camsys_mipiphy_probe_cb(183): ff910000.isp mipi phy1 probe success(reg_phy: 0xff968000 reg_vir: 0xe2ef8000 size: 0x4000)
[ 0.929770] D1:camsys_platform_probe(1394): ff910000.isp memory:
[ 0.929789] D1:camsys_platform_probe(1404): Register memory (phy: 0xff910000 vir: 0xe2f20000 size: 0x10000)
[ 0.929805] D1:camsys_platform_probe(1399): I2c memory (phy: 0x5801000 vir: 0xc5801000 size: 0x1000)
[ 0.929820] D1:camsys_init_ext_fsh_module(20): init external flash module
[ 0.929832] D1:camsys_platform_probe(1419): Probe ff910000.isp device success
[ 0.930182] not find test_power_init dev node
[ 0.930706] rockchip_temp_probe,line=375
[ 0.931020] tsadc ff280000.tsadc: Missing tsadc_low_temp in the DT.
[ 0.932956] DVFS ERR: dvfs_target: clk_gpu is disable, set rate error
[ 0.982110] tsadc ff280000.tsadc: initialized
[ 0.982541] device-mapper: uevent: version 1.0.3
[ 0.982795] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[ 0.983021] Bluetooth: HCI UART driver ver 2.2
[ 0.983036] Bluetooth: HCI H4 protocol initialized
[ 0.983048] Bluetooth: HCILL protocol initialized
[ 0.983060] rtk_btusb: Realtek Bluetooth USB driver module init, version 3.0
[ 0.983072] rtk_btusb: Register usb char device interface for BT driver
[ 0.983245] usbcore: registered new interface driver rtk_btusb
[ 0.986621] cpufreq version 1.0, suspend freq 1200 MHz
[ 0.987170] cpuidle: using governor ladder
[ 0.987186] cpuidle: using governor menu
[ 0.987224] Synopsys Designware Multimedia Card Interface Driver
[ 0.987236] MHSC version = Ver 2.00 2015-06-10
[ 0.987540] dwmmc_rockchip ff0f0000.rksdmmc: Version ID is 270a
[ 0.987625] dwmmc_rockchip ff0f0000.rksdmmc: failed to get hpclk_mmc
[ 0.987917] dwmmc_rockchip ff0f0000.rksdmmc: Using internal DMA controller.
[ 0.988082] dwmmc_rockchip ff0f0000.rksdmmc: dw_mci_init_slot: fmin=400000, fmax=100000000 [mmc0]
[ 0.988227] dwmmc_rockchip ff0f0000.rksdmmc: dw_mci_set_ios: no card. [mmc0]
[ 1.001802] dwmmc_rockchip ff0f0000.rksdmmc: dw_mci_set_ios: no card. [mmc0]
[ 1.011709] dwc_otg_hcd_suspend, usb device mode
[ 1.021575] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out 800000Hz for init[mmc0]
[ 1.021589] dwmmc_rockchip ff0f0000.rksdmmc: DW MMC controller at irq 67, 32 bit host data width, 256 deep fifo
[ 1.021599] dwmmc_rockchip ff0f0000.rksdmmc: 1 slots initialized
[ 1.021961] dwmmc_rockchip ff0c0000.rksdmmc: Version ID is 270a
[ 1.022096] dwmmc_rockchip ff0c0000.rksdmmc: failed to get hpclk_mmc
[ 1.022779] dwmmc_rockchip ff0c0000.rksdmmc: Using internal DMA controller.
[ 1.023216] dwmmc_rockchip ff0c0000.rksdmmc: dw_mci_init_slot: fmin=400000, fmax=50000000 [mmc1]
[ 1.023633] dwmmc_rockchip ff0c0000.rksdmmc: mmc1: No udbg pinctrl found!
[ 1.023700] dwmmc_rockchip ff0c0000.rksdmmc: dw_mci_set_ios: no card. [mmc1]
[ 1.041161] dwmmc_rockchip ff0c0000.rksdmmc: dw_mci_set_ios: no card. [mmc1]
[ 1.053615] mmc0: BKOPS_EN bit is not set
[ 1.055505] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 52000000Hz, actual 50000000HZ div = 1)
[ 1.055528] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out normal clock [mmc0]
[ 1.055581] rk_sdmmc: BOOT Bus speed=50000000Hz,Bus width=8bits.[mmc0]
[ 1.055690] mmc0: new high speed MMC card at address 0001
[ 1.055957] mmcblk0: mmc0:0001 8WPD3R 7.28 GiB
[ 1.056076] mmcblk0rpmb: mmc0:0001 8WPD3R partition 3 512 KiB
[ 1.056386] parameter: 0x000000000 -- 0x000400000 (4 MB)
[ 1.056397] uboot: 0x000400000 -- 0x000800000 (4 MB)
[ 1.056407] misc: 0x000800000 -- 0x000c00000 (4 MB)
[ 1.056416] resource: 0x000c00000 -- 0x001c00000 (16 MB)
[ 1.056424] kernel: 0x001c00000 -- 0x002c00000 (16 MB)
[ 1.056433] boot: 0x002c00000 -- 0x004c00000 (32 MB)
[ 1.056441] recovery: 0x004c00000 -- 0x006c00000 (32 MB)
[ 1.056450] backup: 0x006c00000 -- 0x00a000000 (52 MB)
[ 1.056458] cache: 0x00a000000 -- 0x012000000 (128 MB)
[ 1.056466] kpanic: 0x012000000 -- 0x012400000 (4 MB)
[ 1.056475] system: 0x012400000 -- 0x072400000 (1536 MB)
[ 1.056483] metadata: 0x072400000 -- 0x073400000 (16 MB)
[ 1.056492] baseparamer: 0x073400000 -- 0x073800000 (4 MB)
[ 1.056500] userdata: 0x073800000 -- 0x0b3800000 (1024 MB)
[ 1.056509] radical_update: 0x0b3800000 -- 0x0b7800000 (64 MB)
[ 1.056532] user: 0x0b7800000 -- 0x1d1c00000 (4516 MB)
[ 1.056564] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16
[ 1.060874] dwmmc_rockchip ff0c0000.rksdmmc: dw_mci_set_ios: no card. [mmc1]
[ 1.060882] dwmmc_rockchip ff0c0000.rksdmmc: DW MMC controller at irq 64, 32 bit host data width, 256 deep fifo
[ 1.060889] dwmmc_rockchip ff0c0000.rksdmmc: 1 slots initialized
[ 1.061194] dwmmc_rockchip ff0d0000.rksdmmc: Version ID is 270a
[ 1.061286] dwmmc_rockchip ff0d0000.rksdmmc: failed to get hpclk_mmc
[ 1.061479] dwmmc_rockchip ff0d0000.rksdmmc: Using internal DMA controller.
[ 1.061611] dwmmc_rockchip ff0d0000.rksdmmc: dw_mci_init_slot: fmin=200000, fmax=50000000 [mmc2]
[ 1.061865] dwmmc_rockchip ff0d0000.rksdmmc: dw_mci_set_ios: no card. [mmc2]
[ 1.080522] dwmmc_rockchip ff0d0000.rksdmmc: dw_mci_set_ios: no card. [mmc2]
[ 1.100206] dwmmc_rockchip ff0d0000.rksdmmc: dw_mci_set_ios: no card. [mmc2]
[ 1.100224] dwmmc_rockchip ff0d0000.rksdmmc: DW MMC controller at irq 65, 32 bit host data width, 256 deep fifo
[ 1.100237] dwmmc_rockchip ff0d0000.rksdmmc: 1 slots initialized
[ 1.100598] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.102051] usbcore: registered new interface driver usbhid
[ 1.102061] usbhid: USB HID core driver
[ 1.102169] ashmem: initialized
[ 1.102282] logger: created 256K log 'log_main'
[ 1.102387] logger: created 256K log 'log_events'
[ 1.102491] logger: created 256K log 'log_radio'
[ 1.102583] logger: created 256K log 'log_system'
[ 1.103628] input: rk29-keypad as /devices/ff100000.adc/key.31/input/input0
[ 1.105245] es8323 probe error
[ 1.105265] ES8323: probe of 2-0010 failed with error -11
[ 1.107825] rockchip-hdmi-i2s rockchip-hdmi-i2s.27: rk-hdmi-i2s-hifi <-> ff890000.rockchip-i2s mapping ok
[ 1.108366] u32 classifier
[ 1.108375] Actions configured
[ 1.108386] Netfilter messages via NETLINK v0.30.
[ 1.108445] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 1.108776] ctnetlink v0.93: registering with nfnetlink.
[ 1.108843] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 1.108852] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 1.109115] xt_time: kernel timezone is -0000
[ 1.109319] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.109451] arp_tables: (C) 2002 David S. Miller
[ 1.109489] TCP: cubic registered
[ 1.109496] Initializing XFRM netlink socket
[ 1.109718] NET: Registered protocol family 10
[ 1.110248] mip6: Mobile IPv6
[ 1.110279] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 1.110397] sit: IPv6 over IPv4 tunneling driver
[ 1.110745] NET: Registered protocol family 17
[ 1.110773] NET: Registered protocol family 15
[ 1.110827] Bridge firewalling registered
[ 1.110840] Ebtables v2.0 registered
[ 1.110991] Bluetooth: RFCOMM TTY layer initialized
[ 1.111020] Bluetooth: RFCOMM socket layer initialized
[ 1.111028] Bluetooth: RFCOMM ver 1.11
[ 1.111037] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 1.111044] Bluetooth: BNEP filters: protocol multicast
[ 1.111057] Bluetooth: BNEP socket layer initialized
[ 1.111065] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 1.111076] Bluetooth: HIDP socket layer initialized
[ 1.111133] l2tp_core: L2TP core driver, V2.0
[ 1.111152] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 1.111160] [WLAN_RFKILL]: Enter rfkill_wlan_init
[ 1.111380] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[ 1.111392] [WLAN_RFKILL]: can't find rockchip,grf property
[ 1.111402] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = rtl8723bs
[ 1.111411] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[ 1.111421] [WLAN_RFKILL]: wlan_platdata_parse_dt: disable wifi io reference voltage control.
[ 1.111431] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[ 1.111455] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,poweren_gpio = 148, flags = 0.
[ 1.111478] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 150, flags = 0.
[ 1.111487] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[ 1.111514] [WLAN_RFKILL]: rockchip_wifi_voltage_select: wifi & sdio reference voltage: 1.8V
[ 1.111523] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[ 1.111566] [BT_RFKILL]: Enter rfkill_rk_init
[ 1.111707] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 139.
[ 1.111726] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,power_gpio = 147.
[ 1.111741] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 149.
[ 1.111756] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 146.
[ 1.111772] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 151.
[ 1.111825] [BT_RFKILL]: Request irq for bt wakeup host
[ 1.111922] [BT_RFKILL]: ** disable irq
[ 1.112006] [BT_RFKILL]: bt_default device registered.
[ 1.112065] Key type dns_resolver registered
[ 1.112811] rk3288_init_suspend
[ 1.112825] rk3288_suspend_init enter
[ 1.113033] rk3288_suspend_init: pm_ctrbits =200007
[ 1.113073] gpio_get_dts_info suspend:4
[ 1.113081] gpio_get_dts_info resume:4
[ 1.113089] rockchip,pmic-suspend_gpios:14007a10 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
[ 1.113122] rockchip,pmic-resume_gpios:2007a11 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
[ 1.113283] clks_gating_suspend_init:clkgt info ok
[ 1.113376] Registering SWP/SWPB emulation handler
[ 1.113390] rockchip_uboot_mem_late_init: Freeing uboot logo memory: 0x02000000@0x7dc00000
[ 1.116674] ddrfreq: verion 1.2 20140526
[ 1.116689] ddrfreq: normal 396MHz video_1080p 240MHz video_4k 396MHz dualview 396MHz idle 0MHz suspend 200MHz reboot 396MHz
[ 1.116699] ddrfreq: auto-freq=1
[ 1.116706] ddrfreq: auto-freq-table[0] 240MHz
[ 1.116713] ddrfreq: auto-freq-table[1] 324MHz
[ 1.116719] ddrfreq: auto-freq-table[2] 396MHz
[ 1.116725] ddrfreq: auto-freq-table[3] 528MHz
[ 1.122759] regulator-dummy: disabling
[ 1.122843]
[ 1.122849] =======================================================
[ 1.122855] ==== Launching Wi-Fi driver! (Powered by Rockchip) ====
[ 1.122860] =======================================================
[ 1.122866] Realtek 8723BS SDIO WiFi driver (Powered by Rockchip) init.
[ 1.122873] [WLAN_RFKILL]: rockchip_wifi_power: 1
[ 1.122879] [WLAN_RFKILL]: rockchip_wifi_ref_voltage: 1
[ 1.122885] [WLAN_RFKILL]: rockchip_wifi_ref_voltage: wifi io reference voltage control is disabled.
[ 1.228119] [WLAN_RFKILL]: wifi turn on power. 148
[ 1.228128] mmc2:mmc host rescan start!
[ 1.228138] RTL871X: module init start
[ 1.228144] RTL871X: rtl8723bs v4.3.16_13854.20150410_BTCOEX20150119-5844
[ 1.228149] RTL871X: build time: Sep 20 2017 19:46:05
[ 1.228155] RTL871X: rtl8723bs BT-Coex version = BTCOEX20150119-5844
[ 1.228199] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter
[ 1.228221] rtw_android_wifictrl_func_add: rockchip_wifi_get_oob_irq :196
[ 1.228227] RTL871X: module init ret=0
[ 1.228290] pcd_pullup, is_on 0
[ 1.228326] file system registered
[ 1.228879] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 1.228887] android_usb gadget: Number of LUNs=2
[ 1.228895] lun0: LUN: removable file: (no medium)
[ 1.228901] lun1: LUN: removable file: (no medium)
[ 1.229066] android_usb gadget: android_usb ready
[ 1.229130] sensor_init: Probe name sensors
[ 1.229148] sensor-dev.c v1.4 add angle calculation support between two gsensors 2013-09-01
[ 1.229678] rtc_hym8563 0-0051: setting system clock to 2011-01-04 09:43:30 UTC (1294134210)
[ 1.234912] rockchip_headset_probe() headset have hook adc mode
[ 1.235060] input: rockchip_headset.30 as /devices/ff100000.adc/rockchip_headset.30/input/input1
[ 1.235675] usbcore: registered new interface driver snd-usb-audio
[ 1.235684] ALSA device list:
[ 1.235689] #0: RK-HDMI-I2S
[ 1.235942] Freeing unused kernel memory: 364K (c0c24000 - c0c7f000)
[ 1.236634] init: error to open scaling_available_frequencies
[ 1.444593] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out 800000Hz for init[mmc2]
[ 1.479846] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[ 1.479867] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out normal clock [mmc2]
[ 1.479914] rk_sdmmc: BOOT Bus speed=50000000Hz,Bus width=4bits.[mmc2]
[ 1.480549] mmc2: new high speed SDIO card at address 0001
[ 1.512164] [WLAN_RFKILL]: rockchip_wifi_mac_addr: enter.
[ 1.512182] [WLAN_RFKILL]: falsh wifi_custom_mac_addr=[00:00:00:00:00:00]
[ 1.512197] [WLAN_RFKILL]: This mac address is not valid, ignored...
[ 1.512833] RTL871X: rtw_ndev_init(wlan0)
[ 1.513287] RTL871X: rtw_ndev_init(p2p0)
[ 1.536284] type=1403 audit(1294134210.800:2): policy loaded auid=4294967295 ses=4294967295
[ 1.541564] init: property_set("ro.hardware", "rk30board") failed
[ 1.563742] init: waitpid failed: No child processes
[ 1.564767] init: property_set("ro.kernel.android.checkjni", "1") failed
[ 1.565254] init: /init.rc: 10: invalid command 'setcon'
[ 1.565302] init: /init.rc: 68: invalid command 'load_all_props'
[ 1.565398] init: could not import file '/init.recovery.rk30board.rc' from '/init.rc'
[ 1.565483] type=1400 audit(1294134210.830:3): avc: denied { setcheckreqprot } for pid=1 comm="init" scontext=u:r:init:s0 tcontext=u:object_r:kernel:s0 tclass=security permissive=1
[ 1.566444] ueventd: ueventd started!
[ 1.566776] type=1400 audit(1294134210.830:4): avc: denied { write } for pid=140 comm="healthd" name="/" dev="tmpfs" ino=2131 scontext=u:r:healthd:s0 tcontext=u:object_r:device:s0 tclass=dir permissive=1
[ 1.566802] type=1400 audit(1294134210.830:5): avc: denied { mknod } for pid=140 comm="healthd" capability=27 scontext=u:r:healthd:s0 tcontext=u:r:healthd:s0 tclass=capability permissive=1
[ 1.566821] type=1400 audit(1294134210.830:6): avc: denied { add_name } for pid=140 comm="healthd" name="__kmsg__" scontext=u:r:healthd:s0 tcontext=u:object_r:device:s0 tclass=dir permissive=1
[ 1.566836] ueventd: invalid gid 'trace'
[ 1.566852] type=1400 audit(1294134210.830:7): avc: denied { create } for pid=140 comm="healthd" name="__kmsg__" scontext=u:r:healthd:s0 tcontext=u:object_r:device:s0 tclass=chr_file permissive=1
[ 1.566889] type=1400 audit(1294134210.830:8): avc: denied { write } for pid=140 comm="healthd" name="__kmsg__" dev="tmpfs" ino=8399 scontext=u:r:healthd:s0 tcontext=u:object_r:device:s0 tclass=chr_file permissive=1
[ 1.566914] type=1400 audit(1294134210.830:9): avc: denied { open } for pid=140 comm="healthd" path="/dev/__kmsg__" dev="tmpfs" ino=8399 scontext=u:r:healthd:s0 tcontext=u:object_r:device:s0 tclass=chr_file permissive=1
[ 1.566943] type=1400 audit(1294134210.830:10): avc: denied { remove_name } for pid=140 comm="healthd" name="__kmsg__" dev="tmpfs" ino=8399 scontext=u:r:healthd:s0 tcontext=u:object_r:device:s0 tclass=dir permissive=1
[ 1.566968] bat_cap: oldcap path is /sys/devices/ff100000.adc
[ 1.567004] bat_cap: oldcap_path no exist
[ 1.567135] healthd: No charger supplies found
[ 1.567146] healthd: No battery devices found
[ 1.658196] ueventd: Coldboot took 0.09s.
[ 1.665081] init: /dev/hw_random not found
[ 1.666150] init: /dev/hw_random not found
[ 1.666716] android_usb: already disabled
[ 1.666845] init: property 'ro.serialno' doesn't exist while expanding '${ro.serialno}'
[ 1.666863] init: cannot expand '${ro.serialno}' while writing to '/sys/class/android_usb/android0/iSerial'
[ 2.891072] dwc_otg_hcd_enable, enable host controller
[ 2.891078] EHCI: rk_ehci_hcd_enable, disable host controller
[ 2.994442] Using Buffer DMA mode
[ 2.994449] Periodic Transfer Interrupt Enhancement - disabled
[ 2.994455] Multiprocessor Interrupt Enhancement - disabled
[ 2.994461] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 2.994467] ^^^^^^^^^^^^^^^^^^Host Mode
[ 3.038734] Init: Power Port (0)
[ 3.038771] ff540000.usb resume, HPRT0:0x21401
[ 3.176452] Indeed it is in host mode hprt0 = 00021501
[ 3.353555] usb 3-1: new high-speed USB device number 2 using usb20_host
[ 3.353627] Indeed it is in host mode hprt0 = 00001101
[ 3.550558] usb 3-1: New USB device found, idVendor=1a40, idProduct=0101
[ 3.550568] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 3.550575] usb 3-1: Product: USB 2.0 Hub
[ 3.550964] hub 3-1:1.0: USB hub found
[ 3.551024] hub 3-1:1.0: 4 ports detected
[ 3.648942] dwc_otg_hc_halt: hcchar.b.chen 1, ep_type 3
[ 3.668432] ff540000.usb suspend, HPRT0:0x1485
[ 3.835721] yemk:mpu6050_load_cablic
[ 3.835728] mpu6050_load_cablic: open file /dev/mtd/mtd6
[ 6.591388] drmboot: module license 'unspecified' taints kernel.
[ 6.591410] Disabling lock debugging due to kernel taint
[ 6.591868] drm init, 20140910
[ 6.592447] drm init ok
[ 6.593047] init: service 'recovery' requires console
[ 6.593106] android_usb: already disabled
[ 6.593238] init: using deprecated syntax for specifying property 'ro.product.manufacturer', use ${name} instead
[ 6.593286] init: using deprecated syntax for specifying property 'ro.product.model', use ${name} instead
[ 6.593329] init: using deprecated syntax for specifying property 'ro.serialno', use ${name} instead
[ 6.593345] init: property 'ro.serialno' doesn't exist while expanding '$ro.serialno'
[ 6.593357] init: cannot expand '$ro.serialno' while writing to '/sys/class/android_usb/android0/iSerial'
[ 6.593371] init: service 'console' requires console
[ 8.785222] [otg id chg] last id -1 current id 1
[ 8.785242] PortPower off
[ 8.785249] rk_battery_charger_detect_cb , battery_charger_detect 6
[ 8.884672] Using Buffer DMA mode
[ 8.884683] Periodic Transfer Interrupt Enhancement - disabled
[ 8.884689] Multiprocessor Interrupt Enhancement - disabled
[ 8.884696] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 8.884702] ^^^^^^^^^^^^^^^^^Device Mode
[ 8.884714] dwc_otg_hcd_resume, usb device mode
[ 8.991896] dwc_otg_hcd_suspend, usb device mode
[ 9.375626] ***************vbus detect*****************
[ 9.377810] rk_battery_charger_detect_cb , battery_charger_detect 1
[ 16.635456] read descriptors
[ 16.635473] read descriptors
[ 16.635481] read strings
[ 16.635516] pcd_pullup, is_on 1
[ 17.247626] **************soft reconnect**************
[ 17.426869] Using Buffer DMA mode
[ 17.426882] Periodic Transfer Interrupt Enhancement - disabled
[ 17.426889] Multiprocessor Interrupt Enhancement - disabled
[ 17.426896] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 17.426902] ^^^^^^^^^^^^^^^^^Device Mode
[ 17.426942] *******************soft connect!!!*******************
[ 17.532914] USB RESET
[ 17.689058] android_work: sent uevent USB_STATE=CONNECTED
[ 17.692636] USB RESET
[ 17.917499] android_usb gadget: high-speed config #1: android
[ 17.917572] android_work: sent uevent USB_STATE=CONFIGURED
[ 60.150141] pcd_pullup, is_on 0
[ 60.150242] android_work: sent uevent USB_STATE=DISCONNECTED
[ 60.607246] healthd: battery l=100 v=0 t=42.4 h=2 st=2 chg=a 2011-01-04 09:44:30.842916112 UTC
[ 70.191824] read descriptors
[ 70.191839] read descriptors
[ 70.191846] read strings
[ 70.191870] pcd_pullup, is_on 1
[ 70.383623] **************soft reconnect**************
[ 70.562865] Using Buffer DMA mode
[ 70.562879] Periodic Transfer Interrupt Enhancement - disabled
[ 70.562885] Multiprocessor Interrupt Enhancement - disabled
[ 70.562892] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 70.562898] ^^^^^^^^^^^^^^^^^Device Mode
[ 70.562936] *******************soft connect!!!*******************
[ 70.669366] USB RESET
[ 70.825622] android_work: sent uevent USB_STATE=CONNECTED
[ 70.829205] USB RESET
[ 71.038707] android_usb gadget: high-speed config #1: android
[ 71.038739] WARN::do_gadget_setup:1320: do_gadget_setup warning: pcd->lock locked without unlock
[ 71.038739]
[ 71.038787] android_work: sent uevent USB_STATE=CONFIGURED
[ 3630.493788] pcd_pullup, is_on 0
[ 3630.493853] android_work: sent uevent USB_STATE=DISCONNECTED
[ 3640.535396] read descriptors
[ 3640.535413] read descriptors
[ 3640.535421] read strings
[ 3640.535444] pcd_pullup, is_on 1
[ 3641.319618] **************soft reconnect**************
[ 3641.498855] Using Buffer DMA mode
[ 3641.498868] Periodic Transfer Interrupt Enhancement - disabled
[ 3641.498874] Multiprocessor Interrupt Enhancement - disabled
[ 3641.498881] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 3641.498887] ^^^^^^^^^^^^^^^^^Device Mode
[ 3641.498926] *******************soft connect!!!*******************
[ 3641.605673] USB RESET
[ 3641.761891] android_work: sent uevent USB_STATE=CONNECTED
[ 3641.765594] USB RESET
[ 3641.974099] android_usb gadget: high-speed config #1: android
[ 3641.974161] android_work: sent uevent USB_STATE=CONFIGURED
|
|
